Re: [PATCH v4 11/26] staging: iio: tsl2583: change newlines to improve readability

[Jonathan Cameron <jic23@kernel.org>]

On 12/11/16 18:19, Brian Masney wrote:
> Add and remove newlines to improve code readability in preparation for
> moving the driver out of staging.
> 
> Signed-off-by: Brian Masney <masneyb@onstation.org>
Applied
> ---
>  drivers/staging/iio/light/tsl2583.c | 14 ++++++++++++--
>  1 file changed, 12 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/staging/iio/light/tsl2583.c b/drivers/staging/iio/light/tsl2583.c
> index be3cbae..8303753 100644
> --- a/drivers/staging/iio/light/tsl2583.c
> +++ b/drivers/staging/iio/light/tsl2583.c
> @@ -202,7 +202,6 @@ static int tsl2583_get_lux(struct iio_dev *indio_dev)
>  	ret = i2c_smbus_write_byte(chip->client,
>  				   (TSL2583_CMD_REG | TSL2583_CMD_SPL_FN |
>  				    TSL2583_CMD_ALS_INT_CLR));
> -
>  	if (ret < 0) {
>  		dev_err(&chip->client->dev, "%s: failed to clear the interrupt bit\n",
>  			__func__);
> @@ -225,8 +224,10 @@ static int tsl2583_get_lux(struct iio_dev *indio_dev)
>  		chip->als_cur_info.lux = 0;
>  		goto done;
>  	}
> +
>  	/* calculate ratio */
>  	ratio = (ch1 << 15) / ch0;
> +
>  	/* convert to unscaled lux using the pointer to the table */
>  	for (p = (struct tsl2583_lux *)tsl2583_device_lux;
>  	     p->ratio != 0 && p->ratio < ratio; p++)
> @@ -273,6 +274,7 @@ static int tsl2583_get_lux(struct iio_dev *indio_dev)
>  	lux64 >>= 13;
>  	lux = lux64;
>  	lux = (lux + 500) / 1000;
> +
>  	if (lux > TSL2583_LUX_CALC_OVER_FLOW) { /* check for overflow */
>  return_max:
>  		lux = TSL2583_LUX_CALC_OVER_FLOW;
> @@ -319,21 +321,23 @@ static int tsl2583_als_calibrate(struct iio_dev *indio_dev)
>  			__func__);
>  		return -ENODATA;
>  	}
> +
>  	lux_val = tsl2583_get_lux(indio_dev);
>  	if (lux_val < 0) {
>  		dev_err(&chip->client->dev, "%s: failed to get lux\n",
>  			__func__);
>  		return lux_val;
>  	}
> +
>  	gain_trim_val = (unsigned int)(((chip->als_settings.als_cal_target)
>  			* chip->als_settings.als_gain_trim) / lux_val);
> -
>  	if ((gain_trim_val < 250) || (gain_trim_val > 4000)) {
>  		dev_err(&chip->client->dev,
>  			"%s: trim_val of %d is not within the range [250, 4000]\n",
>  			__func__, gain_trim_val);
>  		return -ENODATA;
>  	}
> +
>  	chip->als_settings.als_gain_trim = (int)gain_trim_val;
>  
>  	return (int)gain_trim_val;
> @@ -529,6 +533,7 @@ static ssize_t in_illuminance_lux_table_show(struct device *dev,
>  	}
>  
>  	offset += sprintf(buf + offset, "\n");
> +
>  	return offset;
>  }
>  
> @@ -776,6 +781,7 @@ static int tsl2583_probe(struct i2c_client *clientp,
>  	indio_dev = devm_iio_device_alloc(&clientp->dev, sizeof(*chip));
>  	if (!indio_dev)
>  		return -ENOMEM;
> +
>  	chip = iio_priv(indio_dev);
>  	chip->client = clientp;
>  	i2c_set_clientdata(clientp, indio_dev);
> @@ -803,6 +809,7 @@ static int tsl2583_probe(struct i2c_client *clientp,
>  	indio_dev->dev.parent = &clientp->dev;
>  	indio_dev->modes = INDIO_DIRECT_MODE;
>  	indio_dev->name = chip->client->name;
> +
>  	ret = devm_iio_device_register(indio_dev->dev.parent, indio_dev);
>  	if (ret) {
>  		dev_err(&clientp->dev, "%s: iio registration failed\n",
> @@ -819,6 +826,7 @@ static int tsl2583_probe(struct i2c_client *clientp,
>  		return ret;
>  
>  	dev_info(&clientp->dev, "Light sensor found.\n");
> +
>  	return 0;
>  }
>  
> @@ -834,6 +842,7 @@ static int __maybe_unused tsl2583_suspend(struct device *dev)
>  	chip->suspended = true;
>  
>  	mutex_unlock(&chip->als_mutex);
> +
>  	return ret;
>  }
>  
> @@ -848,6 +857,7 @@ static int __maybe_unused tsl2583_resume(struct device *dev)
>  	ret = tsl2583_chip_init_and_power_on(indio_dev);
>  
>  	mutex_unlock(&chip->als_mutex);
> +
>  	return ret;
>  }
>  
>