linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Frank Lee <frank@allwinnertech.com>
To: robh+dt@kernel.org, mripard@kernel.org, wens@csie.org,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org
Cc: tiny.windzz@gmail.com, huangshuosheng@allwinnertech.com,
	liyong@allwinnertech.com, Yangtao Li <frank@allwinnertech.com>
Subject: [PATCH v4 14/16] arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
Date: Tue, 14 Jul 2020 15:20:29 +0800	[thread overview]
Message-ID: <f7f86c648bad6e72f8fc8117b96065bf5326a273.1594708864.git.frank@allwinnertech.com> (raw)
In-Reply-To: <cover.1594708863.git.frank@allwinnertech.com>

From: Yangtao Li <frank@allwinnertech.com>

Allwinner A100 is a new SoC with Cortex-A53 cores, this commit adds
the basical DTSI file of it, including the clock, i2c, pins, sid, ths,
nmi, and UART support.

Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
 .../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 364 ++++++++++++++++++
 1 file changed, 364 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
new file mode 100644
index 000000000000..3fb2443f2121
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun50i-a100-ccu.h>
+#include <dt-bindings/clock/sun50i-a100-r-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-r-ccu.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,armv8";
+			device_type = "cpu";
+			reg = <0x0>;
+			enable-method = "psci";
+		};
+
+		cpu@1 {
+			compatible = "arm,armv8";
+			device_type = "cpu";
+			reg = <0x1>;
+			enable-method = "psci";
+		};
+
+		cpu@2 {
+			compatible = "arm,armv8";
+			device_type = "cpu";
+			reg = <0x2>;
+			enable-method = "psci";
+		};
+
+		cpu@3 {
+			compatible = "arm,armv8";
+			device_type = "cpu";
+			reg = <0x3>;
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	dcxo24M: dcxo24M-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "dcxo24M";
+		#clock-cells = <0>;
+	};
+
+	iosc: internal-osc-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <16000000>;
+		clock-accuracy = <300000000>;
+		clock-output-names = "iosc";
+		#clock-cells = <0>;
+	};
+
+	osc32k: osc32k-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		clock-output-names = "osc32k";
+		#clock-cells = <0>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0x3fffffff>;
+
+		ccu: clock@3001000 {
+			compatible = "allwinner,sun50i-a100-ccu";
+			reg = <0x03001000 0x1000>;
+			clocks = <&dcxo24M>, <&osc32k>, <&iosc>;
+			clock-names = "hosc", "losc", "iosc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		gic: interrupt-controller@3021000 {
+			compatible = "arm,gic-400";
+			reg = <0x03021000 0x1000>, <0x03022000 0x2000>,
+			      <0x03024000 0x2000>, <0x03026000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
+						 IRQ_TYPE_LEVEL_HIGH)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		sid@3006000 {
+			compatible = "allwinner,sun50i-a100-sid",
+				     "allwinner,sun50i-a64-sid";
+			reg = <0x03006000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ths_calibration: calib@14 {
+				reg = <0x14 8>;
+			};
+		};
+
+		pio: pinctrl@300b000 {
+			compatible = "allwinner,sun50i-a100-pinctrl";
+			reg = <0x0300b000 0x400>;
+			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_APB1>, <&dcxo24M>, <&osc32k>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			uart0_pb_pins: uart0-pb-pins {
+				pins = "PB9", "PB10";
+				function = "uart0";
+			};
+		};
+
+		uart0: serial@5000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@5000400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@5000800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
+			status = "disabled";
+		};
+
+		uart3: serial@5000c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART3>;
+			resets = <&ccu RST_BUS_UART3>;
+			status = "disabled";
+		};
+
+		uart4: serial@5001000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001000 0x400>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART4>;
+			resets = <&ccu RST_BUS_UART4>;
+			status = "disabled";
+		};
+
+		i2c0: i2c@5002000 {
+			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002000 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@5002400 {
+			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002400 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@5002800 {
+			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002800 0x400>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c3: i2c@5002c00 {
+			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002c00 0x400>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C3>;
+			resets = <&ccu RST_BUS_I2C3>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		ths: thermal-sensor@5070400 {
+			compatible = "allwinner,sun50i-a100-ths";
+			reg = <0x05070400 0x100>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_THS>;
+			clock-names = "bus";
+			resets = <&ccu RST_BUS_THS>;
+			nvmem-cells = <&ths_calibration>;
+			nvmem-cell-names = "calibration";
+			#thermal-sensor-cells = <1>;
+		};
+
+		r_ccu: clock@7010000 {
+			compatible = "allwinner,sun50i-a100-r-ccu";
+			reg = <0x07010000 0x300>;
+			clocks = <&dcxo24M>, <&osc32k>, <&iosc>,
+				 <&ccu CLK_PLL_PERIPH0>;
+			clock-names = "hosc", "losc", "iosc", "pll-periph";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		r_intc: interrupt-controller@7010320 {
+			compatible = "allwinner,sun50i-a100-nmi",
+				     "allwinner,sun9i-a80-nmi";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x07010320 0xc>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		r_pio: pinctrl@7022000 {
+			compatible = "allwinner,sun50i-a100-r-pinctrl";
+			reg = <0x07022000 0x400>;
+			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB1>, <&dcxo24M>, <&osc32k>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			r_i2c0_pins: r-i2c0-pins {
+				pins = "PL0", "PL1";
+				function = "s_i2c0";
+			};
+
+			r_i2c1_pins: r-i2c1-pins {
+				pins = "PL8", "PL9";
+				function = "s_i2c1";
+			};
+		};
+
+		r_uart: serial@7080000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x07080000 0x400>;
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&r_ccu CLK_R_APB2_UART>;
+			resets = <&r_ccu RST_R_APB2_UART>;
+			status = "disabled";
+		};
+
+		r_i2c0: i2c@7081400 {
+			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x07081400 0x400>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_I2C0>;
+			resets = <&r_ccu RST_R_APB2_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_i2c0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		r_i2c1: i2c@7081800 {
+			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x07081800 0x400>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_I2C1>;
+			resets = <&r_ccu RST_R_APB2_I2C1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_i2c1_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	thermal-zones {
+		cpu-thermal-zone {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths 0>;
+		};
+
+		gpu-thermal-zone {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths 1>;
+		};
+
+		ddr-thermal-zone {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths 2>;
+		};
+	};
+};
-- 
2.24.0


  parent reply	other threads:[~2020-07-14  7:20 UTC|newest]

Thread overview: 34+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-07-14  6:55 [PATCH v4 00/16] Allwinner A100 Initial support Frank Lee
2020-07-14  6:59 ` [PATCH v4 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU Frank Lee
2020-07-14  7:02 ` [PATCH v4 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee
2020-07-14  7:03 ` [PATCH v4 03/16] dt-bindings: pinctrl: sunxi: Get rid of continual nesting Frank Lee
2020-07-14 20:50   ` Rob Herring
2020-07-14  7:06 ` [PATCH v4 04/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings Frank Lee
2020-07-14 20:51   ` Rob Herring
2020-07-14  7:07 ` [PATCH v4 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller Frank Lee
2020-07-14  7:08 ` [PATCH v4 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller Frank Lee
2020-07-14 20:51   ` Rob Herring
2020-07-20  9:23   ` Srinivas Kandagatla
2020-07-14  7:11 ` [PATCH v4 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller Frank Lee
2020-07-14  7:13 ` [PATCH v4 08/16] thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate Frank Lee
2020-07-17  4:26   ` Daniel Lezcano
2020-07-17  7:35     ` Frank Lee
2020-07-17  7:56       ` Daniel Lezcano
2020-07-20  9:27         ` Frank Lee
2020-07-20 10:38           ` Daniel Lezcano
2020-07-23 16:56             ` Maxime Ripard
2020-07-14  7:14 ` [PATCH v4 09/16] thermal: sun8i: Add A100's THS controller support Frank Lee
2020-07-14  7:15 ` [PATCH v4 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C Frank Lee
2020-07-14 11:54   ` Chen-Yu Tsai
2020-07-14  7:16 ` [PATCH v4 11/16] dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi Frank Lee
2020-07-14  7:17 ` [PATCH v4 12/16] dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller Frank Lee
2020-07-14  7:18 ` [PATCH v4 13/16] dt-bindings: i2c: mv64xxx: Add compatible for the A100 i2c node Frank Lee
2020-07-22 10:55   ` Wolfram Sang
2020-07-14  7:20 ` Frank Lee [this message]
2020-07-23 16:54   ` [PATCH v4 14/16] arm64: allwinner: A100: add the basical Allwinner A100 DTSI file Maxime Ripard
2020-07-24  6:25     ` Frank Lee
2020-07-24  8:12       ` Maxime Ripard
2020-07-14  7:21 ` [PATCH v4 15/16] dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings Frank Lee
2020-07-14  7:22 ` [PATCH v4 16/16] arm64: allwinner: A100: add support for Allwinner Perf1 board Frank Lee
2020-07-17  4:28 ` [PATCH v4 00/16] Allwinner A100 Initial support Daniel Lezcano
2020-07-17  7:38   ` Frank Lee

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=f7f86c648bad6e72f8fc8117b96065bf5326a273.1594708864.git.frank@allwinnertech.com \
    --to=frank@allwinnertech.com \
    --cc=devicetree@vger.kernel.org \
    --cc=huangshuosheng@allwinnertech.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=liyong@allwinnertech.com \
    --cc=mripard@kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=tiny.windzz@gmail.com \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).