From: Vladimir Oltean <olteanv@gmail.com>
To: andrew@lunn.ch, f.fainelli@gmail.com, vivien.didelot@gmail.com,
davem@davemloft.net, jakub.kicinski@netronome.com
Cc: murali.policharla@broadcom.com, stephen@networkplumber.org,
jiri@resnulli.us, idosch@idosch.org, kuba@kernel.org,
nikolay@cumulusnetworks.com, netdev@vger.kernel.org
Subject: [PATCH v2 net-next 07/10] net: dsa: sja1105: Implement the port MTU callbacks
Date: Wed, 25 Mar 2020 17:22:06 +0200 [thread overview]
Message-ID: <20200325152209.3428-8-olteanv@gmail.com> (raw)
In-Reply-To: <20200325152209.3428-1-olteanv@gmail.com>
From: Vladimir Oltean <vladimir.oltean@nxp.com>
On this switch, the frame length enforcements are performed by the
ingress policers. There are 2 types of those: regular L2 (also called
best-effort) and Virtual Link policers (an ARINC664/AFDX concept for
defining L2 streams with certain QoS abilities). To avoid future
confusion, I prefer to call the reset reason "Best-effort policers",
even though the VL policers are not yet supported.
We also need to change the setup of the initial static config, such that
DSA calls to .change_mtu (which are expensive) become no-ops and don't
reset the switch 5 times.
A driver-level decision is to unconditionally allow single VLAN-tagged
traffic on all ports. The CPU port must accept an additional VLAN header
for the DSA tag, which is again a driver-level decision.
The policers actually count bytes not only from the SDU, but also from
the Ethernet header and FCS, so those need to be accounted for as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
drivers/net/dsa/sja1105/sja1105.h | 1 +
drivers/net/dsa/sja1105/sja1105_main.c | 48 +++++++++++++++++++++++---
2 files changed, 45 insertions(+), 4 deletions(-)
diff --git a/drivers/net/dsa/sja1105/sja1105.h b/drivers/net/dsa/sja1105/sja1105.h
index a358fc89a6db..0e5b739b2fe8 100644
--- a/drivers/net/dsa/sja1105/sja1105.h
+++ b/drivers/net/dsa/sja1105/sja1105.h
@@ -126,6 +126,7 @@ enum sja1105_reset_reason {
SJA1105_RX_HWTSTAMPING,
SJA1105_AGEING_TIME,
SJA1105_SCHEDULING,
+ SJA1105_BEST_EFFORT_POLICING,
};
int sja1105_static_config_reload(struct sja1105_private *priv,
diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index e0c99bb63cdf..5f3392e5678b 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -519,12 +519,12 @@ static int sja1105_init_avb_params(struct sja1105_private *priv)
#define SJA1105_RATE_MBPS(speed) (((speed) * 64000) / 1000)
static void sja1105_setup_policer(struct sja1105_l2_policing_entry *policing,
- int index)
+ int index, int mtu)
{
policing[index].sharindx = index;
policing[index].smax = 65535; /* Burst size in bytes */
policing[index].rate = SJA1105_RATE_MBPS(1000);
- policing[index].maxlen = ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN;
+ policing[index].maxlen = mtu;
policing[index].partition = 0;
}
@@ -556,12 +556,16 @@ static int sja1105_init_l2_policing(struct sja1105_private *priv)
*/
for (i = 0, k = 0; i < SJA1105_NUM_PORTS; i++) {
int bcast = (SJA1105_NUM_PORTS * SJA1105_NUM_TC) + i;
+ int mtu = VLAN_ETH_FRAME_LEN + ETH_FCS_LEN;
+
+ if (dsa_is_cpu_port(priv->ds, i))
+ mtu += VLAN_HLEN;
for (j = 0; j < SJA1105_NUM_TC; j++, k++)
- sja1105_setup_policer(policing, k);
+ sja1105_setup_policer(policing, k, mtu);
/* Set up this port's policer for broadcast traffic */
- sja1105_setup_policer(policing, bcast);
+ sja1105_setup_policer(policing, bcast, mtu);
}
return 0;
}
@@ -1544,6 +1548,7 @@ static const char * const sja1105_reset_reasons[] = {
[SJA1105_RX_HWTSTAMPING] = "RX timestamping",
[SJA1105_AGEING_TIME] = "Ageing time",
[SJA1105_SCHEDULING] = "Time-aware scheduling",
+ [SJA1105_BEST_EFFORT_POLICING] = "Best-effort policing",
};
/* For situations where we need to change a setting at runtime that is only
@@ -2120,6 +2125,39 @@ static int sja1105_set_ageing_time(struct dsa_switch *ds,
return sja1105_static_config_reload(priv, SJA1105_AGEING_TIME);
}
+static int sja1105_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
+{
+ int bcast = (SJA1105_NUM_PORTS * SJA1105_NUM_TC) + port;
+ struct sja1105_l2_policing_entry *policing;
+ struct sja1105_private *priv = ds->priv;
+ int tc;
+
+ new_mtu += VLAN_ETH_HLEN + ETH_FCS_LEN;
+
+ if (dsa_is_cpu_port(ds, port))
+ new_mtu += VLAN_HLEN;
+
+ policing = priv->static_config.tables[BLK_IDX_L2_POLICING].entries;
+
+ /* We set all 9 port policers to the same value, so just checking the
+ * broadcast one is fine.
+ */
+ if (policing[bcast].maxlen == new_mtu)
+ return 0;
+
+ for (tc = 0; tc < SJA1105_NUM_TC; tc++)
+ policing[port * SJA1105_NUM_TC + tc].maxlen = new_mtu;
+
+ policing[bcast].maxlen = new_mtu;
+
+ return sja1105_static_config_reload(priv, SJA1105_BEST_EFFORT_POLICING);
+}
+
+static int sja1105_get_max_mtu(struct dsa_switch *ds, int port)
+{
+ return 2043 - VLAN_ETH_HLEN - ETH_FCS_LEN;
+}
+
static int sja1105_port_setup_tc(struct dsa_switch *ds, int port,
enum tc_setup_type type,
void *type_data)
@@ -2215,6 +2253,8 @@ static const struct dsa_switch_ops sja1105_switch_ops = {
.setup = sja1105_setup,
.teardown = sja1105_teardown,
.set_ageing_time = sja1105_set_ageing_time,
+ .port_change_mtu = sja1105_change_mtu,
+ .port_max_mtu = sja1105_get_max_mtu,
.phylink_validate = sja1105_phylink_validate,
.phylink_mac_link_state = sja1105_mac_pcs_get_state,
.phylink_mac_config = sja1105_mac_config,
--
2.17.1
next prev parent reply other threads:[~2020-03-25 15:22 UTC|newest]
Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-25 15:21 [PATCH v2 net-next 00/10] Configure the MTU on DSA switches Vladimir Oltean
2020-03-25 15:22 ` [PATCH v2 net-next 01/10] net: dsa: configure the MTU for switch ports Vladimir Oltean
2020-03-25 15:22 ` [PATCH v2 net-next 02/10] net: phy: bcm7xx: Add jumbo frame configuration to PHY Vladimir Oltean
2020-03-25 15:44 ` Heiner Kallweit
2020-03-25 22:45 ` Vladimir Oltean
2020-03-25 23:02 ` Florian Fainelli
2020-03-25 23:21 ` Heiner Kallweit
2020-03-25 15:22 ` [PATCH v2 net-next 03/10] bgmac: Add support for Jumbo frames Vladimir Oltean
2020-03-25 15:22 ` [PATCH v2 net-next 04/10] bgmac: Add MTU configuration support to the driver Vladimir Oltean
2020-03-25 15:22 ` [PATCH v2 net-next 05/10] bgmac: Add DMA support to handle frames beyond 8192 bytes Vladimir Oltean
2020-03-25 23:07 ` Florian Fainelli
2020-03-25 15:22 ` [PATCH v2 net-next 06/10] net: dsa: b53: Add MTU configuration support Vladimir Oltean
2020-03-25 23:21 ` Florian Fainelli
2020-03-26 0:48 ` Vladimir Oltean
2020-03-25 15:22 ` Vladimir Oltean [this message]
2020-03-25 23:08 ` [PATCH v2 net-next 07/10] net: dsa: sja1105: Implement the port MTU callbacks Florian Fainelli
2020-03-25 15:22 ` [PATCH v2 net-next 08/10] net: dsa: vsc73xx: Make the MTU configurable Vladimir Oltean
2020-03-25 23:09 ` Florian Fainelli
2020-03-25 15:22 ` [PATCH v2 net-next 09/10] net: dsa: felix: support changing the MTU Vladimir Oltean
2020-03-25 23:10 ` Florian Fainelli
2020-03-25 15:22 ` [PATCH v2 net-next 10/10] net: bridge: implement auto-normalization of MTU for hardware datapath Vladimir Oltean
2020-03-25 23:17 ` Florian Fainelli
2020-03-26 0:30 ` Vladimir Oltean
2020-03-26 10:17 ` Ido Schimmel
2020-03-26 10:25 ` Vladimir Oltean
2020-03-26 11:35 ` Ido Schimmel
2020-03-26 11:44 ` Vladimir Oltean
2020-03-26 11:54 ` Ido Schimmel
2020-03-26 12:34 ` Vladimir Oltean
2020-03-26 12:59 ` Ido Schimmel
2020-03-26 12:06 ` Nikolay Aleksandrov
2020-03-26 12:18 ` Vladimir Oltean
2020-03-26 12:19 ` Nikolay Aleksandrov
2020-03-26 12:25 ` Vladimir Oltean
2020-03-26 12:38 ` Nikolay Aleksandrov
2020-03-26 18:49 ` Jakub Kicinski
2020-03-26 19:41 ` Nikolay Aleksandrov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200325152209.3428-8-olteanv@gmail.com \
--to=olteanv@gmail.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=idosch@idosch.org \
--cc=jakub.kicinski@netronome.com \
--cc=jiri@resnulli.us \
--cc=kuba@kernel.org \
--cc=murali.policharla@broadcom.com \
--cc=netdev@vger.kernel.org \
--cc=nikolay@cumulusnetworks.com \
--cc=stephen@networkplumber.org \
--cc=vivien.didelot@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).