[PATCH AUTOSEL 4.19 02/12] net: mscc: ocelot: fix fields offset in SG_CONFIG_REG_3

[PATCH AUTOSEL 4.19 02/12] net: mscc: ocelot: fix fields offset in SG_CONFIG_REG_3

[Sasha Levin]

From: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>

[ Upstream commit 4ab810a4e04ab6c851007033d39c13e6d3f55110 ]

INIT_IPS and GATE_ENABLE fields have a wrong offset in SG_CONFIG_REG_3.
This register is used by stream gate control of PSFP, and it has not
been used before, because PSFP is not implemented in ocelot driver.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/mscc/ocelot_ana.h | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/mscc/ocelot_ana.h b/drivers/net/ethernet/mscc/ocelot_ana.h
index 841c6ec22b641..1669481d97794 100644
--- a/drivers/net/ethernet/mscc/ocelot_ana.h
+++ b/drivers/net/ethernet/mscc/ocelot_ana.h
@@ -252,10 +252,10 @@
 #define ANA_SG_CONFIG_REG_3_LIST_LENGTH_M                 GENMASK(18, 16)
 #define ANA_SG_CONFIG_REG_3_LIST_LENGTH_X(x)              (((x) & GENMASK(18, 16)) >> 16)
 #define ANA_SG_CONFIG_REG_3_GATE_ENABLE                   BIT(20)
-#define ANA_SG_CONFIG_REG_3_INIT_IPS(x)                   (((x) << 24) & GENMASK(27, 24))
-#define ANA_SG_CONFIG_REG_3_INIT_IPS_M                    GENMASK(27, 24)
-#define ANA_SG_CONFIG_REG_3_INIT_IPS_X(x)                 (((x) & GENMASK(27, 24)) >> 24)
-#define ANA_SG_CONFIG_REG_3_INIT_GATE_STATE               BIT(28)
+#define ANA_SG_CONFIG_REG_3_INIT_IPS(x)                   (((x) << 21) & GENMASK(24, 21))
+#define ANA_SG_CONFIG_REG_3_INIT_IPS_M                    GENMASK(24, 21)
+#define ANA_SG_CONFIG_REG_3_INIT_IPS_X(x)                 (((x) & GENMASK(24, 21)) >> 21)
+#define ANA_SG_CONFIG_REG_3_INIT_GATE_STATE               BIT(25)
 
 #define ANA_SG_GCL_GS_CONFIG_RSZ                          0x4
 
-- 
2.25.1

[PATCH AUTOSEL 4.19 03/12] net/fsl: quieten expected MDIO access failures

[Sasha Levin]

From: Jamie Iles <jamie@nuviainc.com>

[ Upstream commit 1ec8e74855588cecb2620b28b877c08f45765374 ]

MDIO reads can happen during PHY probing, and printing an error with
dev_err can result in a large number of error messages during device
probe.  On a platform with a serial console this can result in
excessively long boot times in a way that looks like an infinite loop
when multiple busses are present.  Since 0f183fd151c (net/fsl: enable
extended scanning in xgmac_mdio) we perform more scanning so there are
potentially more failures.

Reduce the logging level to dev_dbg which is consistent with the
Freescale enetc driver.

Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/freescale/xgmac_mdio.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/freescale/xgmac_mdio.c b/drivers/net/ethernet/freescale/xgmac_mdio.c
index c82c85ef5fb34..61cb4ba0005bd 100644
--- a/drivers/net/ethernet/freescale/xgmac_mdio.c
+++ b/drivers/net/ethernet/freescale/xgmac_mdio.c
@@ -229,7 +229,7 @@ static int xgmac_mdio_read(struct mii_bus *bus, int phy_id, int regnum)
 	/* Return all Fs if nothing was there */
 	if ((xgmac_read32(&regs->mdio_stat, endian) & MDIO_STAT_RD_ER) &&
 	    !priv->has_a011043) {
-		dev_err(&bus->dev,
+		dev_dbg(&bus->dev,
 			"Error while reading PHY%d reg at %d.%hhu\n",
 			phy_id, dev_addr, regnum);
 		return 0xffff;
-- 
2.25.1

[PATCH AUTOSEL 4.19 04/12] net: usb: ax88179_178a: add Toshiba usb 3.0 adapter

[Sasha Levin]

From: Wilken Gottwalt <wilken.gottwalt@mailbox.org>

[ Upstream commit e42d72fea91f8f2e82b65808739ca04b7a8cd7a8 ]

Adds the driver_info and usb ids of the AX88179 based Toshiba USB 3.0
ethernet adapter.

Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/ax88179_178a.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/drivers/net/usb/ax88179_178a.c b/drivers/net/usb/ax88179_178a.c
index 8455f72007b9e..ba6c6f834c508 100644
--- a/drivers/net/usb/ax88179_178a.c
+++ b/drivers/net/usb/ax88179_178a.c
@@ -1740,6 +1740,19 @@ static const struct driver_info belkin_info = {
 	.tx_fixup = ax88179_tx_fixup,
 };
 
+static const struct driver_info toshiba_info = {
+	.description = "Toshiba USB Ethernet Adapter",
+	.bind	= ax88179_bind,
+	.unbind = ax88179_unbind,
+	.status = ax88179_status,
+	.link_reset = ax88179_link_reset,
+	.reset	= ax88179_reset,
+	.stop = ax88179_stop,
+	.flags	= FLAG_ETHER | FLAG_FRAMING_AX,
+	.rx_fixup = ax88179_rx_fixup,
+	.tx_fixup = ax88179_tx_fixup,
+};
+
 static const struct usb_device_id products[] = {
 {
 	/* ASIX AX88179 10/100/1000 */
@@ -1773,6 +1786,10 @@ static const struct usb_device_id products[] = {
 	/* Belkin B2B128 USB 3.0 Hub + Gigabit Ethernet Adapter */
 	USB_DEVICE(0x050d, 0x0128),
 	.driver_info = (unsigned long)&belkin_info,
+}, {
+	/* Toshiba USB 3.0 GBit Ethernet Adapter */
+	USB_DEVICE(0x0930, 0x0a13),
+	.driver_info = (unsigned long)&toshiba_info,
 },
 	{ },
 };
-- 
2.25.1

[PATCH AUTOSEL 4.19 05/12] net: usb: ax88179_178a: add MCT usb 3.0 adapter

[Sasha Levin]

From: Wilken Gottwalt <wilken.gottwalt@mailbox.org>

[ Upstream commit c92a79829c7c169139874aa1d4bf6da32d10c38a ]

Adds the driver_info and usb ids of the AX88179 based MCT U3-A9003 USB
3.0 ethernet adapter.

Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/ax88179_178a.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/drivers/net/usb/ax88179_178a.c b/drivers/net/usb/ax88179_178a.c
index ba6c6f834c508..25308a793231c 100644
--- a/drivers/net/usb/ax88179_178a.c
+++ b/drivers/net/usb/ax88179_178a.c
@@ -1753,6 +1753,19 @@ static const struct driver_info toshiba_info = {
 	.tx_fixup = ax88179_tx_fixup,
 };
 
+static const struct driver_info mct_info = {
+	.description = "MCT USB 3.0 Gigabit Ethernet Adapter",
+	.bind	= ax88179_bind,
+	.unbind	= ax88179_unbind,
+	.status	= ax88179_status,
+	.link_reset = ax88179_link_reset,
+	.reset	= ax88179_reset,
+	.stop	= ax88179_stop,
+	.flags	= FLAG_ETHER | FLAG_FRAMING_AX,
+	.rx_fixup = ax88179_rx_fixup,
+	.tx_fixup = ax88179_tx_fixup,
+};
+
 static const struct usb_device_id products[] = {
 {
 	/* ASIX AX88179 10/100/1000 */
@@ -1790,6 +1803,10 @@ static const struct usb_device_id products[] = {
 	/* Toshiba USB 3.0 GBit Ethernet Adapter */
 	USB_DEVICE(0x0930, 0x0a13),
 	.driver_info = (unsigned long)&toshiba_info,
+}, {
+	/* Magic Control Technology U3-A9003 USB 3.0 Gigabit Ethernet Adapter */
+	USB_DEVICE(0x0711, 0x0179),
+	.driver_info = (unsigned long)&mct_info,
 },
 	{ },
 };
-- 
2.25.1

[PATCH AUTOSEL 4.19 06/12] via-rhine: Fix for the hardware having a reset failure after resume

[Sasha Levin]

From: Kevin Brace <kevinbrace@bracecomputerlab.com>

[ Upstream commit d120c9a81e32c43cba8017dec873b6a414898716 ]

In rhine_resume() and rhine_suspend(), the code calls netif_running()
to see if the network interface is down or not.  If it is down (i.e.,
netif_running() returning false), they will skip any housekeeping work
within the function relating to the hardware.  This becomes a problem
when the hardware resumes from a standby since it is counting on
rhine_resume() to map its MMIO and power up rest of the hardware.
Not getting its MMIO remapped and rest of the hardware powered
up lead to a soft reset failure and hardware disappearance.  The
solution is to map its MMIO and power up rest of the hardware inside
rhine_open() before soft reset is to be performed.  This solution was
verified on ASUS P5V800-VM mainboard's integrated Rhine-II Ethernet
MAC inside VIA Technologies VT8251 South Bridge.

Signed-off-by: Kevin Brace <kevinbrace@bracecomputerlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/via/via-rhine.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/via/via-rhine.c b/drivers/net/ethernet/via/via-rhine.c
index 33949248c829e..b38ab17e9b132 100644
--- a/drivers/net/ethernet/via/via-rhine.c
+++ b/drivers/net/ethernet/via/via-rhine.c
@@ -1710,6 +1710,8 @@ static int rhine_open(struct net_device *dev)
 		goto out_free_ring;
 
 	alloc_tbufs(dev);
+	enable_mmio(rp->pioaddr, rp->quirks);
+	rhine_power_init(dev);
 	rhine_chip_reset(dev);
 	rhine_task_enable(rp);
 	init_registers(dev);
-- 
2.25.1

[PATCH AUTOSEL 4.19 07/12] via-rhine: VTunknown1 device is really VT8251 South Bridge

[Sasha Levin]

From: Kevin Brace <kevinbrace@bracecomputerlab.com>

[ Upstream commit aa15190cf2cf25ec7e6c6d7373ae3ca563d48601 ]

The VIA Technologies VT8251 South Bridge's integrated Rhine-II
Ethernet MAC comes has a PCI revision value of 0x7c.  This was
verified on ASUS P5V800-VM mainboard.

Signed-off-by: Kevin Brace <kevinbrace@bracecomputerlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/via/via-rhine.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/via/via-rhine.c b/drivers/net/ethernet/via/via-rhine.c
index b38ab17e9b132..c62a4ea54df00 100644
--- a/drivers/net/ethernet/via/via-rhine.c
+++ b/drivers/net/ethernet/via/via-rhine.c
@@ -243,7 +243,7 @@ enum rhine_revs {
 	VT8233		= 0x60,	/* Integrated MAC */
 	VT8235		= 0x74,	/* Integrated MAC */
 	VT8237		= 0x78,	/* Integrated MAC */
-	VTunknown1	= 0x7C,
+	VT8251		= 0x7C,	/* Integrated MAC */
 	VT6105		= 0x80,
 	VT6105_B0	= 0x83,
 	VT6105L		= 0x8A,
-- 
2.25.1

[PATCH AUTOSEL 4.19 08/12] net: usb: pegasus: Proper error handing when setting pegasus' MAC address

[Sasha Levin]

From: Petko Manolov <petko.manolov@konsulko.com>

[ Upstream commit f30e25a9d1b25ac8d40071c4dc2679ad0fcdc55a ]

v2:

If reading the MAC address from eeprom fail don't throw an error, use randomly
generated MAC instead.  Either way the adapter will soldier on and the return
type of set_ethernet_addr() can be reverted to void.

v1:

Fix a bug in set_ethernet_addr() which does not take into account possible
errors (or partial reads) returned by its helpers.  This can potentially lead to
writing random data into device's MAC address registers.

Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/pegasus.c | 35 +++++++++++++++++++++++++++--------
 1 file changed, 27 insertions(+), 8 deletions(-)

diff --git a/drivers/net/usb/pegasus.c b/drivers/net/usb/pegasus.c
index b7a0df95d4b0f..17c4f516ddb33 100644
--- a/drivers/net/usb/pegasus.c
+++ b/drivers/net/usb/pegasus.c
@@ -362,28 +362,47 @@ fail:
 }
 #endif				/* PEGASUS_WRITE_EEPROM */
 
-static inline void get_node_id(pegasus_t *pegasus, __u8 *id)
+static inline int get_node_id(pegasus_t *pegasus, u8 *id)
 {
-	int i;
-	__u16 w16;
+	int i, ret;
+	u16 w16;
 
 	for (i = 0; i < 3; i++) {
-		read_eprom_word(pegasus, i, &w16);
+		ret = read_eprom_word(pegasus, i, &w16);
+		if (ret < 0)
+			return ret;
 		((__le16 *) id)[i] = cpu_to_le16(w16);
 	}
+
+	return 0;
 }
 
 static void set_ethernet_addr(pegasus_t *pegasus)
 {
-	__u8 node_id[6];
+	int ret;
+	u8 node_id[6];
 
 	if (pegasus->features & PEGASUS_II) {
-		get_registers(pegasus, 0x10, sizeof(node_id), node_id);
+		ret = get_registers(pegasus, 0x10, sizeof(node_id), node_id);
+		if (ret < 0)
+			goto err;
 	} else {
-		get_node_id(pegasus, node_id);
-		set_registers(pegasus, EthID, sizeof(node_id), node_id);
+		ret = get_node_id(pegasus, node_id);
+		if (ret < 0)
+			goto err;
+		ret = set_registers(pegasus, EthID, sizeof(node_id), node_id);
+		if (ret < 0)
+			goto err;
 	}
+
 	memcpy(pegasus->net->dev_addr, node_id, sizeof(node_id));
+
+	return;
+err:
+	eth_hw_addr_random(pegasus->net);
+	dev_info(&pegasus->intf->dev, "software assigned MAC address.\n");
+
+	return;
 }
 
 static inline int reset_mac(pegasus_t *pegasus)
-- 
2.25.1

[PATCH AUTOSEL 4.19 09/12] net: usb: rtl8150: set random MAC address when set_ethernet_addr() fails

[Sasha Levin]

From: Anant Thazhemadam <anant.thazhemadam@gmail.com>

[ Upstream commit f45a4248ea4cc13ed50618ff066849f9587226b2 ]

When get_registers() fails in set_ethernet_addr(),the uninitialized
value of node_id gets copied over as the address.
So, check the return value of get_registers().

If get_registers() executed successfully (i.e., it returns
sizeof(node_id)), copy over the MAC address using ether_addr_copy()
(instead of using memcpy()).

Else, if get_registers() failed instead, a randomly generated MAC
address is set as the MAC address instead.

Reported-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Tested-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/rtl8150.c | 16 ++++++++++++----
 1 file changed, 12 insertions(+), 4 deletions(-)

diff --git a/drivers/net/usb/rtl8150.c b/drivers/net/usb/rtl8150.c
index 80373a9171dd2..933d1a74bcdb3 100644
--- a/drivers/net/usb/rtl8150.c
+++ b/drivers/net/usb/rtl8150.c
@@ -277,12 +277,20 @@ static int write_mii_word(rtl8150_t * dev, u8 phy, __u8 indx, u16 reg)
 		return 1;
 }
 
-static inline void set_ethernet_addr(rtl8150_t * dev)
+static void set_ethernet_addr(rtl8150_t *dev)
 {
-	u8 node_id[6];
+	u8 node_id[ETH_ALEN];
+	int ret;
+
+	ret = get_registers(dev, IDR, sizeof(node_id), node_id);
 
-	get_registers(dev, IDR, sizeof(node_id), node_id);
-	memcpy(dev->netdev->dev_addr, node_id, sizeof(node_id));
+	if (ret == sizeof(node_id)) {
+		ether_addr_copy(dev->netdev->dev_addr, node_id);
+	} else {
+		eth_hw_addr_random(dev->netdev);
+		netdev_notice(dev->netdev, "Assigned a random MAC address: %pM\n",
+			      dev->netdev->dev_addr);
+	}
 }
 
 static int rtl8150_set_mac_address(struct net_device *netdev, void *p)
-- 
2.25.1

[PATCH AUTOSEL 4.19 12/12] net: usb: qmi_wwan: add Cellient MPL200 card

[Sasha Levin]

From: Wilken Gottwalt <wilken.gottwalt@mailbox.org>

[ Upstream commit 28802e7c0c9954218d1830f7507edc9d49b03a00 ]

Add usb ids of the Cellient MPL200 card.

Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/qmi_wwan.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/usb/qmi_wwan.c b/drivers/net/usb/qmi_wwan.c
index af58bf54aa9b6..d2612b69257ea 100644
--- a/drivers/net/usb/qmi_wwan.c
+++ b/drivers/net/usb/qmi_wwan.c
@@ -1312,6 +1312,7 @@ static const struct usb_device_id products[] = {
 	{QMI_QUIRK_SET_DTR(0x2cb7, 0x0104, 4)},	/* Fibocom NL678 series */
 	{QMI_FIXED_INTF(0x0489, 0xe0b4, 0)},	/* Foxconn T77W968 LTE */
 	{QMI_FIXED_INTF(0x0489, 0xe0b5, 0)},	/* Foxconn T77W968 LTE with eSIM support*/
+	{QMI_FIXED_INTF(0x2692, 0x9025, 4)},    /* Cellient MPL200 (rebranded Qualcomm 05c6:9025) */
 
 	/* 4. Gobi 1000 devices */
 	{QMI_GOBI1K_DEVICE(0x05c6, 0x9212)},	/* Acer Gobi Modem Device */
-- 
2.25.1