From: Grygorii Strashko <grygorii.strashko@ti.com>
To: Ilias Apalodimas <ilias.apalodimas@linaro.org>,
<netdev@vger.kernel.org>, <ivan.khoronzhuk@linaro.org>,
<nsekhar@ti.com>, <jiri@resnulli.us>, <ivecera@redhat.com>
Cc: <francois.ozog@linaro.org>, <yogeshs@ti.com>, <spatton@ti.com>
Subject: Re: [PATCH 0/4] RFC CPSW switchdev mode
Date: Fri, 1 Jun 2018 16:29:08 -0500 [thread overview]
Message-ID: <4277c55c-bea2-1061-35e9-62d1d0f60d28@ti.com> (raw)
In-Reply-To: <1527144984-31236-1-git-send-email-ilias.apalodimas@linaro.org>
Hi Ilias,
On 05/24/2018 01:56 AM, Ilias Apalodimas wrote:
> Hello,
>
> This is adding a new mode on the cpsw driver based around switchdev.
> In order to enable this you need to enable CONFIG_NET_SWITCHDEV,
> CONFIG_BRIDGE_VLAN_FILTERING, CONFIG_TI_CPSW_SWITCHDEV
> and add to udev config:
>
> SUBSYSTEM=="net", ACTION=="add", ATTR{phys_switch_id}=="0f011900", \
> ATTR{phys_port_name}!="", NAME="sw0$attr{phys_port_name}"
> Since the phys_switch_id is based on cpsw version, users with different
> version will need to do 'ip -d link show dev sw0p0 | grep switchid' and
> replace with the correct value.
>
> This patch creates 3 ports, sw0p0, sw0p1 and sw0p2.
> sw0p1 and sw0p2 are the netdev interfaces connected to PHY devices
> while sw0p0 is the switch 'cpu facing port'.
> sw0p0 will be unable to receive and transmit traffic and it's not 100% within
> switchdev scope but, it's used to configure switch cpu port individually as
> this is needed for various switch features and configuration scenarios.
First, sorry for delayed reply it was very tough week (new SoC).
Second, Thanks a lot for your great work. I'm still testing it with different
use cases and trying to consolidate my reply for all questions.
All, thanks for your comments.
--
regards,
-grygorii
next prev parent reply other threads:[~2018-06-01 21:29 UTC|newest]
Thread overview: 53+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-24 6:56 [PATCH 0/4] RFC CPSW switchdev mode Ilias Apalodimas
2018-05-24 6:56 ` [PATCH 1/4] cpsw: move common headers definitions to cpsw_priv.h Ilias Apalodimas
2018-05-24 6:56 ` [PATCH 2/4] cpsw_ale: add support functions for switchdev Ilias Apalodimas
2018-05-24 6:56 ` [PATCH 3/4] cpsw_switchdev: add switchdev support files Ilias Apalodimas
2018-05-24 10:00 ` Maxim Uvarov
2018-05-27 4:39 ` kbuild test robot
2018-05-24 6:56 ` [PATCH 4/4] cpsw: add switchdev support Ilias Apalodimas
2018-05-24 13:12 ` Andrew Lunn
2018-05-24 13:32 ` Ilias Apalodimas
2018-05-24 16:39 ` Andrew Lunn
2018-05-25 4:56 ` Ilias Apalodimas
2018-06-01 21:48 ` Florian Fainelli
2018-06-02 10:34 ` Ilias Apalodimas
2018-06-02 16:10 ` Florian Fainelli
2018-06-02 16:52 ` Ilias Apalodimas
2018-06-05 21:03 ` Grygorii Strashko
2018-06-05 21:37 ` Florian Fainelli
2018-05-24 8:05 ` [PATCH 0/4] RFC CPSW switchdev mode Jiri Pirko
2018-05-24 8:48 ` Ilias Apalodimas
2018-05-24 12:54 ` Andrew Lunn
2018-05-24 13:44 ` Ivan Vecera
2018-05-24 14:08 ` Ilias Apalodimas
2018-05-24 14:54 ` Andrew Lunn
2018-05-24 15:07 ` Ilias Apalodimas
2018-05-24 15:25 ` Andrew Lunn
2018-05-24 16:02 ` Ilias Apalodimas
2018-05-24 16:33 ` Andrew Lunn
2018-05-25 6:29 ` Ilias Apalodimas
2018-05-25 10:28 ` Ilias Apalodimas
2018-05-25 11:59 ` Andrew Lunn
2018-05-25 12:09 ` Andrew Lunn
2018-05-31 15:27 ` Ilias Apalodimas
2018-06-02 23:28 ` Grygorii Strashko
2018-06-03 0:08 ` Andrew Lunn
2018-06-05 21:18 ` Grygorii Strashko
2018-06-05 21:28 ` Andrew Lunn
2018-06-05 21:42 ` Grygorii Strashko
2018-06-05 21:55 ` Andrew Lunn
2018-06-03 0:26 ` Andrew Lunn
2018-06-05 23:23 ` Grygorii Strashko
2018-06-05 23:49 ` Andrew Lunn
2018-06-06 8:23 ` Ivan Khoronzhuk
2018-06-03 0:37 ` Andrew Lunn
2018-06-05 21:31 ` Grygorii Strashko
2018-06-05 21:37 ` Andrew Lunn
2018-06-03 0:49 ` Andrew Lunn
2018-06-05 22:45 ` Grygorii Strashko
2018-06-05 23:40 ` Andrew Lunn
2018-06-01 21:29 ` Grygorii Strashko [this message]
2018-06-02 14:08 ` Andrew Lunn
2018-06-05 22:59 ` Grygorii Strashko
2018-06-05 23:53 ` Andrew Lunn
2018-06-06 6:42 ` Ilias Apalodimas
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4277c55c-bea2-1061-35e9-62d1d0f60d28@ti.com \
--to=grygorii.strashko@ti.com \
--cc=francois.ozog@linaro.org \
--cc=ilias.apalodimas@linaro.org \
--cc=ivan.khoronzhuk@linaro.org \
--cc=ivecera@redhat.com \
--cc=jiri@resnulli.us \
--cc=netdev@vger.kernel.org \
--cc=nsekhar@ti.com \
--cc=spatton@ti.com \
--cc=yogeshs@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).