* [PATCH] ath10k: snoc: enable threaded napi on WCN3990 @ 2022-12-20 7:55 Abhishek Kumar 2022-12-20 12:14 ` Manikanta Pubbisetty 2022-12-20 15:10 ` Dave Taht 0 siblings, 2 replies; 9+ messages in thread From: Abhishek Kumar @ 2022-12-20 7:55 UTC (permalink / raw) To: kvalo Cc: ath10k, linux-wireless, kuabhs, linux-kernel, netdev, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni NAPI poll can be done in threaded context along with soft irq context. Threaded context can be scheduled efficiently, thus creating less of bottleneck during Rx processing. This patch is to enable threaded NAPI on ath10k driver. Based on testing, it was observed that on WCN3990, the CPU0 reaches 100% utilization when napi runs in softirq context. At the same time the other CPUs are at low consumption percentage. This does not allow device to reach its maximum throughput potential. After enabling threaded napi, CPU load is balanced across all CPUs and following improvments were observed: - UDP_RX increase by ~22-25% - TCP_RX increase by ~15% Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00696-QCAHLSWMTPL-1 Signed-off-by: Abhishek Kumar <kuabhs@chromium.org> --- drivers/net/wireless/ath/ath10k/core.c | 16 ++++++++++++++++ drivers/net/wireless/ath/ath10k/hw.h | 2 ++ drivers/net/wireless/ath/ath10k/snoc.c | 3 +++ 3 files changed, 21 insertions(+) diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c index 5eb131ab916fd..ee4b6ba508c81 100644 --- a/drivers/net/wireless/ath/ath10k/core.c +++ b/drivers/net/wireless/ath/ath10k/core.c @@ -100,6 +100,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA988X_HW_2_0_VERSION, @@ -140,6 +141,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA9887_HW_1_0_VERSION, @@ -181,6 +183,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA6174_HW_3_2_VERSION, @@ -217,6 +220,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA6174_HW_2_1_VERSION, @@ -257,6 +261,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA6174_HW_2_1_VERSION, @@ -297,6 +302,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA6174_HW_3_0_VERSION, @@ -337,6 +343,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA6174_HW_3_2_VERSION, @@ -381,6 +388,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA99X0_HW_2_0_DEV_VERSION, @@ -427,6 +435,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA9984_HW_1_0_DEV_VERSION, @@ -480,6 +489,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA9888_HW_2_0_DEV_VERSION, @@ -530,6 +540,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA9377_HW_1_0_DEV_VERSION, @@ -570,6 +581,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA9377_HW_1_1_DEV_VERSION, @@ -612,6 +624,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA9377_HW_1_1_DEV_VERSION, @@ -645,6 +658,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = QCA4019_HW_1_0_DEV_VERSION, @@ -692,6 +706,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = false, .use_fw_tx_credits = true, .delay_unmap_buffer = false, + .enable_threaded_napi = false, }, { .id = WCN3990_HW_1_0_DEV_VERSION, @@ -725,6 +740,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .hw_restart_disconnect = true, .use_fw_tx_credits = false, .delay_unmap_buffer = true, + .enable_threaded_napi = true, }, }; diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h index 9643031a4427a..adf3076b96503 100644 --- a/drivers/net/wireless/ath/ath10k/hw.h +++ b/drivers/net/wireless/ath/ath10k/hw.h @@ -639,6 +639,8 @@ struct ath10k_hw_params { bool use_fw_tx_credits; bool delay_unmap_buffer; + + bool enable_threaded_napi; }; struct htt_resp; diff --git a/drivers/net/wireless/ath/ath10k/snoc.c b/drivers/net/wireless/ath/ath10k/snoc.c index cfcb759a87dea..b94150fb6ef06 100644 --- a/drivers/net/wireless/ath/ath10k/snoc.c +++ b/drivers/net/wireless/ath/ath10k/snoc.c @@ -927,6 +927,9 @@ static int ath10k_snoc_hif_start(struct ath10k *ar) bitmap_clear(ar_snoc->pending_ce_irqs, 0, CE_COUNT_MAX); + if (ar->hw_params.enable_threaded_napi) + dev_set_threaded(&ar->napi_dev, true); + ath10k_core_napi_enable(ar); ath10k_snoc_irq_enable(ar); ath10k_snoc_rx_post(ar); -- 2.39.0.314.g84b9a713c41-goog ^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH] ath10k: snoc: enable threaded napi on WCN3990 2022-12-20 7:55 [PATCH] ath10k: snoc: enable threaded napi on WCN3990 Abhishek Kumar @ 2022-12-20 12:14 ` Manikanta Pubbisetty 2022-12-29 0:01 ` Abhishek Kumar 2022-12-20 15:10 ` Dave Taht 1 sibling, 1 reply; 9+ messages in thread From: Manikanta Pubbisetty @ 2022-12-20 12:14 UTC (permalink / raw) To: Abhishek Kumar, kvalo Cc: ath10k, linux-wireless, linux-kernel, netdev, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni On 12/20/2022 1:25 PM, Abhishek Kumar wrote: > NAPI poll can be done in threaded context along with soft irq > context. Threaded context can be scheduled efficiently, thus > creating less of bottleneck during Rx processing. This patch is > to enable threaded NAPI on ath10k driver. > > Based on testing, it was observed that on WCN3990, the CPU0 reaches > 100% utilization when napi runs in softirq context. At the same > time the other CPUs are at low consumption percentage. This > does not allow device to reach its maximum throughput potential. > After enabling threaded napi, CPU load is balanced across all CPUs > and following improvments were observed: > - UDP_RX increase by ~22-25% > - TCP_RX increase by ~15% > > Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00696-QCAHLSWMTPL-1 > Signed-off-by: Abhishek Kumar <kuabhs@chromium.org> > --- > > drivers/net/wireless/ath/ath10k/core.c | 16 ++++++++++++++++ > drivers/net/wireless/ath/ath10k/hw.h | 2 ++ > drivers/net/wireless/ath/ath10k/snoc.c | 3 +++ > 3 files changed, 21 insertions(+) > > diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c > index 5eb131ab916fd..ee4b6ba508c81 100644 > --- a/drivers/net/wireless/ath/ath10k/core.c > +++ b/drivers/net/wireless/ath/ath10k/core.c > @@ -100,6 +100,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA988X_HW_2_0_VERSION, > @@ -140,6 +141,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9887_HW_1_0_VERSION, > @@ -181,6 +183,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA6174_HW_3_2_VERSION, > @@ -217,6 +220,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA6174_HW_2_1_VERSION, > @@ -257,6 +261,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA6174_HW_2_1_VERSION, > @@ -297,6 +302,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA6174_HW_3_0_VERSION, > @@ -337,6 +343,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA6174_HW_3_2_VERSION, > @@ -381,6 +388,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA99X0_HW_2_0_DEV_VERSION, > @@ -427,6 +435,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9984_HW_1_0_DEV_VERSION, > @@ -480,6 +489,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9888_HW_2_0_DEV_VERSION, > @@ -530,6 +540,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9377_HW_1_0_DEV_VERSION, > @@ -570,6 +581,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9377_HW_1_1_DEV_VERSION, > @@ -612,6 +624,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9377_HW_1_1_DEV_VERSION, > @@ -645,6 +658,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA4019_HW_1_0_DEV_VERSION, > @@ -692,6 +706,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = WCN3990_HW_1_0_DEV_VERSION, > @@ -725,6 +740,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = true, > .use_fw_tx_credits = false, > .delay_unmap_buffer = true, > + .enable_threaded_napi = true, > }, > }; > > diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h > index 9643031a4427a..adf3076b96503 100644 > --- a/drivers/net/wireless/ath/ath10k/hw.h > +++ b/drivers/net/wireless/ath/ath10k/hw.h > @@ -639,6 +639,8 @@ struct ath10k_hw_params { > bool use_fw_tx_credits; > > bool delay_unmap_buffer; > + > + bool enable_threaded_napi; > }; > > struct htt_resp; > diff --git a/drivers/net/wireless/ath/ath10k/snoc.c b/drivers/net/wireless/ath/ath10k/snoc.c > index cfcb759a87dea..b94150fb6ef06 100644 > --- a/drivers/net/wireless/ath/ath10k/snoc.c > +++ b/drivers/net/wireless/ath/ath10k/snoc.c > @@ -927,6 +927,9 @@ static int ath10k_snoc_hif_start(struct ath10k *ar) > > bitmap_clear(ar_snoc->pending_ce_irqs, 0, CE_COUNT_MAX); > > + if (ar->hw_params.enable_threaded_napi) > + dev_set_threaded(&ar->napi_dev, true); > + Since this is done in the API specific to WCN3990, we do not need hw_param for this. Thanks, Manikanta ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ath10k: snoc: enable threaded napi on WCN3990 2022-12-20 12:14 ` Manikanta Pubbisetty @ 2022-12-29 0:01 ` Abhishek Kumar 2023-01-12 10:15 ` Kalle Valo 0 siblings, 1 reply; 9+ messages in thread From: Abhishek Kumar @ 2022-12-29 0:01 UTC (permalink / raw) To: Manikanta Pubbisetty Cc: kvalo, ath10k, linux-wireless, linux-kernel, netdev, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni Apologies for the late reply. Please see my response inline. On Tue, Dec 20, 2022 at 4:14 AM Manikanta Pubbisetty <quic_mpubbise@quicinc.com> wrote: > > On 12/20/2022 1:25 PM, Abhishek Kumar wrote: > > NAPI poll can be done in threaded context along with soft irq > > context. Threaded context can be scheduled efficiently, thus > > creating less of bottleneck during Rx processing. This patch is > > to enable threaded NAPI on ath10k driver. > > > > Based on testing, it was observed that on WCN3990, the CPU0 reaches > > 100% utilization when napi runs in softirq context. At the same > > time the other CPUs are at low consumption percentage. This > > does not allow device to reach its maximum throughput potential. > > After enabling threaded napi, CPU load is balanced across all CPUs > > and following improvments were observed: > > - UDP_RX increase by ~22-25% > > - TCP_RX increase by ~15% > > > > Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00696-QCAHLSWMTPL-1 > > Signed-off-by: Abhishek Kumar <kuabhs@chromium.org> > > --- > > > > drivers/net/wireless/ath/ath10k/core.c | 16 ++++++++++++++++ > > drivers/net/wireless/ath/ath10k/hw.h | 2 ++ > > drivers/net/wireless/ath/ath10k/snoc.c | 3 +++ > > 3 files changed, 21 insertions(+) > > > > diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c > > index 5eb131ab916fd..ee4b6ba508c81 100644 > > --- a/drivers/net/wireless/ath/ath10k/core.c > > +++ b/drivers/net/wireless/ath/ath10k/core.c > > @@ -100,6 +100,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA988X_HW_2_0_VERSION, > > @@ -140,6 +141,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9887_HW_1_0_VERSION, > > @@ -181,6 +183,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA6174_HW_3_2_VERSION, > > @@ -217,6 +220,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA6174_HW_2_1_VERSION, > > @@ -257,6 +261,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA6174_HW_2_1_VERSION, > > @@ -297,6 +302,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA6174_HW_3_0_VERSION, > > @@ -337,6 +343,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA6174_HW_3_2_VERSION, > > @@ -381,6 +388,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA99X0_HW_2_0_DEV_VERSION, > > @@ -427,6 +435,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9984_HW_1_0_DEV_VERSION, > > @@ -480,6 +489,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9888_HW_2_0_DEV_VERSION, > > @@ -530,6 +540,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9377_HW_1_0_DEV_VERSION, > > @@ -570,6 +581,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9377_HW_1_1_DEV_VERSION, > > @@ -612,6 +624,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9377_HW_1_1_DEV_VERSION, > > @@ -645,6 +658,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA4019_HW_1_0_DEV_VERSION, > > @@ -692,6 +706,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = WCN3990_HW_1_0_DEV_VERSION, > > @@ -725,6 +740,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = true, > > .use_fw_tx_credits = false, > > .delay_unmap_buffer = true, > > + .enable_threaded_napi = true, > > }, > > }; > > > > diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h > > index 9643031a4427a..adf3076b96503 100644 > > --- a/drivers/net/wireless/ath/ath10k/hw.h > > +++ b/drivers/net/wireless/ath/ath10k/hw.h > > @@ -639,6 +639,8 @@ struct ath10k_hw_params { > > bool use_fw_tx_credits; > > > > bool delay_unmap_buffer; > > + > > + bool enable_threaded_napi; > > }; > > > > struct htt_resp; > > diff --git a/drivers/net/wireless/ath/ath10k/snoc.c b/drivers/net/wireless/ath/ath10k/snoc.c > > index cfcb759a87dea..b94150fb6ef06 100644 > > --- a/drivers/net/wireless/ath/ath10k/snoc.c > > +++ b/drivers/net/wireless/ath/ath10k/snoc.c > > @@ -927,6 +927,9 @@ static int ath10k_snoc_hif_start(struct ath10k *ar) > > > > bitmap_clear(ar_snoc->pending_ce_irqs, 0, CE_COUNT_MAX); > > > > + if (ar->hw_params.enable_threaded_napi) > > + dev_set_threaded(&ar->napi_dev, true); > > + > > Since this is done in the API specific to WCN3990, we do not need > hw_param for this. Just so that I am clear, are you suggesting to enable this by default in snoc.c, similar to what you did in https://lore.kernel.org/all/20220905071805.31625-2-quic_mpubbise@quicinc.com/ . If my understanding is correct and there is no objection, I can remove hw_param and enable it by default on snoc.c . I used hw_param because, as I see it, threaded NAPI can have some adverse effect on the cache utilization and power. Thanks Abhishek > > Thanks, > Manikanta ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ath10k: snoc: enable threaded napi on WCN3990 2022-12-29 0:01 ` Abhishek Kumar @ 2023-01-12 10:15 ` Kalle Valo 2023-01-27 22:08 ` Abhishek Kumar 0 siblings, 1 reply; 9+ messages in thread From: Kalle Valo @ 2023-01-12 10:15 UTC (permalink / raw) To: Abhishek Kumar Cc: Manikanta Pubbisetty, ath10k, linux-wireless, linux-kernel, netdev, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni Abhishek Kumar <kuabhs@chromium.org> writes: >> > --- a/drivers/net/wireless/ath/ath10k/snoc.c >> > +++ b/drivers/net/wireless/ath/ath10k/snoc.c >> > @@ -927,6 +927,9 @@ static int ath10k_snoc_hif_start(struct ath10k *ar) >> > >> > bitmap_clear(ar_snoc->pending_ce_irqs, 0, CE_COUNT_MAX); >> > >> > + if (ar->hw_params.enable_threaded_napi) >> > + dev_set_threaded(&ar->napi_dev, true); >> > + >> >> Since this is done in the API specific to WCN3990, we do not need >> hw_param for this. > > Just so that I am clear, are you suggesting to enable this by default > in snoc.c, similar to what you did in > > https://lore.kernel.org/all/20220905071805.31625-2-quic_mpubbise@quicinc.com/ > > If my understanding is correct and there is no objection, I can remove > hw_param and enable it by default on snoc.c . I used hw_param because, > as I see it, threaded NAPI can have some adverse effect on the cache > utilization and power. WCN3990 is the only device using SNOC bus so the hw_param is not needed. It's safe to call dev_set_threaded() in ath10k_snoc_hif_start() unconditionally as it only affects WCN3990. -- https://patchwork.kernel.org/project/linux-wireless/list/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ath10k: snoc: enable threaded napi on WCN3990 2023-01-12 10:15 ` Kalle Valo @ 2023-01-27 22:08 ` Abhishek Kumar 0 siblings, 0 replies; 9+ messages in thread From: Abhishek Kumar @ 2023-01-27 22:08 UTC (permalink / raw) To: Kalle Valo Cc: Manikanta Pubbisetty, ath10k, linux-wireless, linux-kernel, netdev, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni Thanks for all the comments. I will call dev_set_threaded() directly without HW params and rollout a v2 soon. On Thu, Jan 12, 2023 at 2:15 AM Kalle Valo <kvalo@kernel.org> wrote: > > Abhishek Kumar <kuabhs@chromium.org> writes: > > >> > --- a/drivers/net/wireless/ath/ath10k/snoc.c > >> > +++ b/drivers/net/wireless/ath/ath10k/snoc.c > >> > @@ -927,6 +927,9 @@ static int ath10k_snoc_hif_start(struct ath10k *ar) > >> > > >> > bitmap_clear(ar_snoc->pending_ce_irqs, 0, CE_COUNT_MAX); > >> > > >> > + if (ar->hw_params.enable_threaded_napi) > >> > + dev_set_threaded(&ar->napi_dev, true); > >> > + > >> > >> Since this is done in the API specific to WCN3990, we do not need > >> hw_param for this. > > > > Just so that I am clear, are you suggesting to enable this by default > > in snoc.c, similar to what you did in > > > > https://lore.kernel.org/all/20220905071805.31625-2-quic_mpubbise@quicinc.com/ > > > > If my understanding is correct and there is no objection, I can remove > > hw_param and enable it by default on snoc.c . I used hw_param because, > > as I see it, threaded NAPI can have some adverse effect on the cache > > utilization and power. > > WCN3990 is the only device using SNOC bus so the hw_param is not needed. > It's safe to call dev_set_threaded() in ath10k_snoc_hif_start() > unconditionally as it only affects WCN3990. > > -- > https://patchwork.kernel.org/project/linux-wireless/list/ > > https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ath10k: snoc: enable threaded napi on WCN3990 2022-12-20 7:55 [PATCH] ath10k: snoc: enable threaded napi on WCN3990 Abhishek Kumar 2022-12-20 12:14 ` Manikanta Pubbisetty @ 2022-12-20 15:10 ` Dave Taht 2022-12-28 23:53 ` Abhishek Kumar 1 sibling, 1 reply; 9+ messages in thread From: Dave Taht @ 2022-12-20 15:10 UTC (permalink / raw) To: Abhishek Kumar Cc: kvalo, ath10k, linux-wireless, linux-kernel, netdev, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni, Make-Wifi-fast I am always interested in flent.org tcp_nup, tcp_ndown, and rrul_be tests on wifi hardware. In AP mode, especially, against a few clients in rtt_fair on the "ending the anomaly" test suite at the bottom of this link: https://www.cs.kau.se/tohojo/airtime-fairness/ . Of these, it's trying to optimize bandwidth more fairly and keep latencies low when 4 or more stations are trying to transmit (in a world with 16 or more stations online), that increasingly bothers me the most. I'm seeing 5+ seconds on some rtt_fair-like tests nowadays. I was also seeing huge simultaneous upload vs download disparities on the latest kernels, on various threads over here: https://forum.openwrt.org/t/aql-and-the-ath10k-is-lovely/59002 and more recently here: https://forum.openwrt.org/t/reducing-multiplexing-latencies-still-further-in-wifi/133605 I don't understand why napi with the default budget (64) is even needed on the ath10k, as a single txop takes a minimum of ~200us, but perhaps your patch will help. Still, measuring the TCP statistics in-band would be nice to see. Some new tools are appearing that can do this, Apple's goresponsiveness, crusader... that are simpler to use than flent. On Tue, Dec 20, 2022 at 12:17 AM Abhishek Kumar <kuabhs@chromium.org> wrote: > > NAPI poll can be done in threaded context along with soft irq > context. Threaded context can be scheduled efficiently, thus > creating less of bottleneck during Rx processing. This patch is > to enable threaded NAPI on ath10k driver. > > Based on testing, it was observed that on WCN3990, the CPU0 reaches > 100% utilization when napi runs in softirq context. At the same > time the other CPUs are at low consumption percentage. This > does not allow device to reach its maximum throughput potential. > After enabling threaded napi, CPU load is balanced across all CPUs > and following improvments were observed: > - UDP_RX increase by ~22-25% > - TCP_RX increase by ~15% > > Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00696-QCAHLSWMTPL-1 > Signed-off-by: Abhishek Kumar <kuabhs@chromium.org> > --- > > drivers/net/wireless/ath/ath10k/core.c | 16 ++++++++++++++++ > drivers/net/wireless/ath/ath10k/hw.h | 2 ++ > drivers/net/wireless/ath/ath10k/snoc.c | 3 +++ > 3 files changed, 21 insertions(+) > > diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c > index 5eb131ab916fd..ee4b6ba508c81 100644 > --- a/drivers/net/wireless/ath/ath10k/core.c > +++ b/drivers/net/wireless/ath/ath10k/core.c > @@ -100,6 +100,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA988X_HW_2_0_VERSION, > @@ -140,6 +141,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9887_HW_1_0_VERSION, > @@ -181,6 +183,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA6174_HW_3_2_VERSION, > @@ -217,6 +220,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA6174_HW_2_1_VERSION, > @@ -257,6 +261,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA6174_HW_2_1_VERSION, > @@ -297,6 +302,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA6174_HW_3_0_VERSION, > @@ -337,6 +343,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA6174_HW_3_2_VERSION, > @@ -381,6 +388,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA99X0_HW_2_0_DEV_VERSION, > @@ -427,6 +435,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9984_HW_1_0_DEV_VERSION, > @@ -480,6 +489,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9888_HW_2_0_DEV_VERSION, > @@ -530,6 +540,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9377_HW_1_0_DEV_VERSION, > @@ -570,6 +581,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9377_HW_1_1_DEV_VERSION, > @@ -612,6 +624,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA9377_HW_1_1_DEV_VERSION, > @@ -645,6 +658,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = QCA4019_HW_1_0_DEV_VERSION, > @@ -692,6 +706,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = false, > .use_fw_tx_credits = true, > .delay_unmap_buffer = false, > + .enable_threaded_napi = false, > }, > { > .id = WCN3990_HW_1_0_DEV_VERSION, > @@ -725,6 +740,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > .hw_restart_disconnect = true, > .use_fw_tx_credits = false, > .delay_unmap_buffer = true, > + .enable_threaded_napi = true, > }, > }; > > diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h > index 9643031a4427a..adf3076b96503 100644 > --- a/drivers/net/wireless/ath/ath10k/hw.h > +++ b/drivers/net/wireless/ath/ath10k/hw.h > @@ -639,6 +639,8 @@ struct ath10k_hw_params { > bool use_fw_tx_credits; > > bool delay_unmap_buffer; > + > + bool enable_threaded_napi; > }; > > struct htt_resp; > diff --git a/drivers/net/wireless/ath/ath10k/snoc.c b/drivers/net/wireless/ath/ath10k/snoc.c > index cfcb759a87dea..b94150fb6ef06 100644 > --- a/drivers/net/wireless/ath/ath10k/snoc.c > +++ b/drivers/net/wireless/ath/ath10k/snoc.c > @@ -927,6 +927,9 @@ static int ath10k_snoc_hif_start(struct ath10k *ar) > > bitmap_clear(ar_snoc->pending_ce_irqs, 0, CE_COUNT_MAX); > > + if (ar->hw_params.enable_threaded_napi) > + dev_set_threaded(&ar->napi_dev, true); > + > ath10k_core_napi_enable(ar); > ath10k_snoc_irq_enable(ar); > ath10k_snoc_rx_post(ar); > -- > 2.39.0.314.g84b9a713c41-goog > -- This song goes out to all the folk that thought Stadia would work: https://www.linkedin.com/posts/dtaht_the-mushroom-song-activity-6981366665607352320-FXtz Dave Täht CEO, TekLibre, LLC ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ath10k: snoc: enable threaded napi on WCN3990 2022-12-20 15:10 ` Dave Taht @ 2022-12-28 23:53 ` Abhishek Kumar 2022-12-29 0:49 ` Dave Taht 0 siblings, 1 reply; 9+ messages in thread From: Abhishek Kumar @ 2022-12-28 23:53 UTC (permalink / raw) To: Dave Taht Cc: kvalo, ath10k, linux-wireless, linux-kernel, netdev, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni, Make-Wifi-fast Apologies for the late reply, Thanks Dave for your comment. My answer is inline. On Tue, Dec 20, 2022 at 7:10 AM Dave Taht <dave.taht@gmail.com> wrote: > > I am always interested in flent.org tcp_nup, tcp_ndown, and rrul_be > tests on wifi hardware. In AP mode, especially, against a few clients > in rtt_fair on the "ending the anomaly" test suite at the bottom of > this link: https://www.cs.kau.se/tohojo/airtime-fairness/ . Of these, > it's trying to optimize bandwidth more fairly and keep latencies low > when 4 or more stations are trying to transmit (in a world with 16 or > more stations online), that increasingly bothers me the most. I'm > seeing 5+ seconds on some rtt_fair-like tests nowadays. I used testing using iperf and conductive setup and fetched the throughput data(mentioned below). > > I was also seeing huge simultaneous upload vs download disparities on > the latest kernels, on various threads over here: > https://forum.openwrt.org/t/aql-and-the-ath10k-is-lovely/59002 and > more recently here: > https://forum.openwrt.org/t/reducing-multiplexing-latencies-still-further-in-wifi/133605 Interesting, thanks for the pointer and probably the Qualcomm team is aware of it. > > I don't understand why napi with the default budget (64) is even > needed on the ath10k, as a single txop takes a minimum of ~200us, but > perhaps your patch will help. Still, measuring the TCP statistics > in-band would be nice to see. Some new tools are appearing that can do > this, Apple's goresponsiveness, crusader... that are simpler to use > than flent. Here are some of the additional raw data with and without threaded napi: ================================================== udp_rx(Without threaded NAPI) 435.98+-5.16 : Channel 44 439.06+-0.66 : Channel 157 udp_rx(With threaded NAPI) 509.73+-41.03 : Channel 44 549.97+-7.62 : Channel 157 =================================================== udp_tx(Without threaded NAPI) 461.31+-0.69 : Channel 44 461.46+-0.78 : Channel 157 udp_tx(With threaded NAPI) 459.20+-0.77 : Channel 44 459.78+-1.08 : Channel 157 =================================================== tcp_rx(Without threaded NAPI) 472.63+-2.35 : Channel 44 469.29+-6.31 : Channel 157 tcp_rx(With threaded NAPI) 498.49+-2.44 : Channel 44 541.14+-40.65 : Channel 157 =================================================== tcp_tx(Without threaded NAPI) 317.34+-2.37 : Channel 44 317.01+-2.56 : Channel 157 tcp_tx(With threaded NAPI) 371.34+-2.36 : Channel 44 376.95+-9.40 : Channel 157 ==================================================== > > On Tue, Dec 20, 2022 at 12:17 AM Abhishek Kumar <kuabhs@chromium.org> wrote: > > > > NAPI poll can be done in threaded context along with soft irq > > context. Threaded context can be scheduled efficiently, thus > > creating less of bottleneck during Rx processing. This patch is > > to enable threaded NAPI on ath10k driver. > > > > Based on testing, it was observed that on WCN3990, the CPU0 reaches > > 100% utilization when napi runs in softirq context. At the same > > time the other CPUs are at low consumption percentage. This > > does not allow device to reach its maximum throughput potential. > > After enabling threaded napi, CPU load is balanced across all CPUs > > and following improvments were observed: > > - UDP_RX increase by ~22-25% > > - TCP_RX increase by ~15% > > > > Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00696-QCAHLSWMTPL-1 > > Signed-off-by: Abhishek Kumar <kuabhs@chromium.org> > > --- > > > > drivers/net/wireless/ath/ath10k/core.c | 16 ++++++++++++++++ > > drivers/net/wireless/ath/ath10k/hw.h | 2 ++ > > drivers/net/wireless/ath/ath10k/snoc.c | 3 +++ > > 3 files changed, 21 insertions(+) > > > > diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c > > index 5eb131ab916fd..ee4b6ba508c81 100644 > > --- a/drivers/net/wireless/ath/ath10k/core.c > > +++ b/drivers/net/wireless/ath/ath10k/core.c > > @@ -100,6 +100,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA988X_HW_2_0_VERSION, > > @@ -140,6 +141,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9887_HW_1_0_VERSION, > > @@ -181,6 +183,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA6174_HW_3_2_VERSION, > > @@ -217,6 +220,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA6174_HW_2_1_VERSION, > > @@ -257,6 +261,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA6174_HW_2_1_VERSION, > > @@ -297,6 +302,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA6174_HW_3_0_VERSION, > > @@ -337,6 +343,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA6174_HW_3_2_VERSION, > > @@ -381,6 +388,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA99X0_HW_2_0_DEV_VERSION, > > @@ -427,6 +435,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9984_HW_1_0_DEV_VERSION, > > @@ -480,6 +489,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9888_HW_2_0_DEV_VERSION, > > @@ -530,6 +540,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9377_HW_1_0_DEV_VERSION, > > @@ -570,6 +581,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9377_HW_1_1_DEV_VERSION, > > @@ -612,6 +624,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA9377_HW_1_1_DEV_VERSION, > > @@ -645,6 +658,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = QCA4019_HW_1_0_DEV_VERSION, > > @@ -692,6 +706,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = false, > > .use_fw_tx_credits = true, > > .delay_unmap_buffer = false, > > + .enable_threaded_napi = false, > > }, > > { > > .id = WCN3990_HW_1_0_DEV_VERSION, > > @@ -725,6 +740,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > .hw_restart_disconnect = true, > > .use_fw_tx_credits = false, > > .delay_unmap_buffer = true, > > + .enable_threaded_napi = true, > > }, > > }; > > > > diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h > > index 9643031a4427a..adf3076b96503 100644 > > --- a/drivers/net/wireless/ath/ath10k/hw.h > > +++ b/drivers/net/wireless/ath/ath10k/hw.h > > @@ -639,6 +639,8 @@ struct ath10k_hw_params { > > bool use_fw_tx_credits; > > > > bool delay_unmap_buffer; > > + > > + bool enable_threaded_napi; > > }; > > > > struct htt_resp; > > diff --git a/drivers/net/wireless/ath/ath10k/snoc.c b/drivers/net/wireless/ath/ath10k/snoc.c > > index cfcb759a87dea..b94150fb6ef06 100644 > > --- a/drivers/net/wireless/ath/ath10k/snoc.c > > +++ b/drivers/net/wireless/ath/ath10k/snoc.c > > @@ -927,6 +927,9 @@ static int ath10k_snoc_hif_start(struct ath10k *ar) > > > > bitmap_clear(ar_snoc->pending_ce_irqs, 0, CE_COUNT_MAX); > > > > + if (ar->hw_params.enable_threaded_napi) > > + dev_set_threaded(&ar->napi_dev, true); > > + > > ath10k_core_napi_enable(ar); > > ath10k_snoc_irq_enable(ar); > > ath10k_snoc_rx_post(ar); > > -- > > 2.39.0.314.g84b9a713c41-goog > > > > > -- > This song goes out to all the folk that thought Stadia would work: > https://www.linkedin.com/posts/dtaht_the-mushroom-song-activity-6981366665607352320-FXtz > Dave Täht CEO, TekLibre, LLC ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] ath10k: snoc: enable threaded napi on WCN3990 2022-12-28 23:53 ` Abhishek Kumar @ 2022-12-29 0:49 ` Dave Taht [not found] ` <CAHb6Lvpta1fJef-M1LasR5zzzudJ2+CNyWwrSo3DU9OoeiFfzA@mail.gmail.com> 0 siblings, 1 reply; 9+ messages in thread From: Dave Taht @ 2022-12-29 0:49 UTC (permalink / raw) To: Abhishek Kumar Cc: kvalo, ath10k, linux-wireless, linux-kernel, netdev, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni, Make-Wifi-fast On Wed, Dec 28, 2022 at 3:53 PM Abhishek Kumar <kuabhs@chromium.org> wrote: > > Apologies for the late reply, Thanks Dave for your comment. My answer is inline. > > On Tue, Dec 20, 2022 at 7:10 AM Dave Taht <dave.taht@gmail.com> wrote: > > > > I am always interested in flent.org tcp_nup, tcp_ndown, and rrul_be > > tests on wifi hardware. In AP mode, especially, against a few clients > > in rtt_fair on the "ending the anomaly" test suite at the bottom of > > this link: https://www.cs.kau.se/tohojo/airtime-fairness/ . Of these, > > it's trying to optimize bandwidth more fairly and keep latencies low > > when 4 or more stations are trying to transmit (in a world with 16 or > > more stations online), that increasingly bothers me the most. I'm > > seeing 5+ seconds on some rtt_fair-like tests nowadays. > I used testing using iperf and conductive setup and fetched the > throughput data(mentioned below). > > > > I was also seeing huge simultaneous upload vs download disparities on > > the latest kernels, on various threads over here: > > https://forum.openwrt.org/t/aql-and-the-ath10k-is-lovely/59002 and > > more recently here: > > https://forum.openwrt.org/t/reducing-multiplexing-latencies-still-further-in-wifi/133605 > Interesting, thanks for the pointer and probably the Qualcomm team is > aware of it. > > > > I don't understand why napi with the default budget (64) is even > > needed on the ath10k, as a single txop takes a minimum of ~200us, but > > perhaps your patch will help. Still, measuring the TCP statistics > > in-band would be nice to see. Some new tools are appearing that can do > > this, Apple's goresponsiveness, crusader... that are simpler to use > > than flent. > Here are some of the additional raw data with and without threaded napi: > ================================================== > udp_rx(Without threaded NAPI) > 435.98+-5.16 : Channel 44 > 439.06+-0.66 : Channel 157 > > udp_rx(With threaded NAPI) > 509.73+-41.03 : Channel 44 > 549.97+-7.62 : Channel 157 > =================================================== > udp_tx(Without threaded NAPI) > 461.31+-0.69 : Channel 44 > 461.46+-0.78 : Channel 157 > > udp_tx(With threaded NAPI) > 459.20+-0.77 : Channel 44 > 459.78+-1.08 : Channel 157 > =================================================== > tcp_rx(Without threaded NAPI) > 472.63+-2.35 : Channel 44 > 469.29+-6.31 : Channel 157 > > tcp_rx(With threaded NAPI) > 498.49+-2.44 : Channel 44 > 541.14+-40.65 : Channel 157 > =================================================== > tcp_tx(Without threaded NAPI) > 317.34+-2.37 : Channel 44 > 317.01+-2.56 : Channel 157 > > tcp_tx(With threaded NAPI) > 371.34+-2.36 : Channel 44 > 376.95+-9.40 : Channel 157 My concern is primarily with the induced tcp latency on this test. A way to check that is to run wireshark on your test client driving the test, capture the iperf traffic, and then plot the "Statistics->TCP stream statistics for both throughput and rtt. Would it be possible for you to do that and put up those plots somewhere? The worst case test is a tcp bidirectional test which I don't know if older iperfs can do. (iperf2 has new bounceback and bidir tests) Ideally stuff going in either direction, would not look as horrible, as it did, back in 2016, documented in this linuxplumbers presentation here: https://blog.linuxplumbersconf.org/2016/ocw/system/presentations/3963/original/linuxplumbers_wifi_latency-3Nov.pdf and discussed on lwn, here: https://lwn.net/Articles/705884/ I worry about folk achieving slightly better tcp throughput at the expense of clobbering in-tcp-stream latency. Back then we were shooting for no more than 40ms extra latency under load on this chip, down from (unusable) seconds. Presently elsewhere, on other chips, we're getting 8ms with stuff that's not in tree for the ath10k, there is a slight cost in single stream throughput but when multiple streams are in use, on multiple stations, things like web pages fly, irrespective of load. > ==================================================== > > > > > On Tue, Dec 20, 2022 at 12:17 AM Abhishek Kumar <kuabhs@chromium.org> wrote: > > > > > > NAPI poll can be done in threaded context along with soft irq > > > context. Threaded context can be scheduled efficiently, thus > > > creating less of bottleneck during Rx processing. This patch is > > > to enable threaded NAPI on ath10k driver. > > > > > > Based on testing, it was observed that on WCN3990, the CPU0 reaches > > > 100% utilization when napi runs in softirq context. At the same > > > time the other CPUs are at low consumption percentage. This > > > does not allow device to reach its maximum throughput potential. > > > After enabling threaded napi, CPU load is balanced across all CPUs > > > and following improvments were observed: > > > - UDP_RX increase by ~22-25% > > > - TCP_RX increase by ~15% > > > > > > Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00696-QCAHLSWMTPL-1 > > > Signed-off-by: Abhishek Kumar <kuabhs@chromium.org> > > > --- > > > > > > drivers/net/wireless/ath/ath10k/core.c | 16 ++++++++++++++++ > > > drivers/net/wireless/ath/ath10k/hw.h | 2 ++ > > > drivers/net/wireless/ath/ath10k/snoc.c | 3 +++ > > > 3 files changed, 21 insertions(+) > > > > > > diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c > > > index 5eb131ab916fd..ee4b6ba508c81 100644 > > > --- a/drivers/net/wireless/ath/ath10k/core.c > > > +++ b/drivers/net/wireless/ath/ath10k/core.c > > > @@ -100,6 +100,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA988X_HW_2_0_VERSION, > > > @@ -140,6 +141,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA9887_HW_1_0_VERSION, > > > @@ -181,6 +183,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA6174_HW_3_2_VERSION, > > > @@ -217,6 +220,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA6174_HW_2_1_VERSION, > > > @@ -257,6 +261,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA6174_HW_2_1_VERSION, > > > @@ -297,6 +302,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA6174_HW_3_0_VERSION, > > > @@ -337,6 +343,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA6174_HW_3_2_VERSION, > > > @@ -381,6 +388,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA99X0_HW_2_0_DEV_VERSION, > > > @@ -427,6 +435,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA9984_HW_1_0_DEV_VERSION, > > > @@ -480,6 +489,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA9888_HW_2_0_DEV_VERSION, > > > @@ -530,6 +540,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA9377_HW_1_0_DEV_VERSION, > > > @@ -570,6 +581,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA9377_HW_1_1_DEV_VERSION, > > > @@ -612,6 +624,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA9377_HW_1_1_DEV_VERSION, > > > @@ -645,6 +658,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = QCA4019_HW_1_0_DEV_VERSION, > > > @@ -692,6 +706,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = false, > > > .use_fw_tx_credits = true, > > > .delay_unmap_buffer = false, > > > + .enable_threaded_napi = false, > > > }, > > > { > > > .id = WCN3990_HW_1_0_DEV_VERSION, > > > @@ -725,6 +740,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { > > > .hw_restart_disconnect = true, > > > .use_fw_tx_credits = false, > > > .delay_unmap_buffer = true, > > > + .enable_threaded_napi = true, > > > }, > > > }; > > > > > > diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h > > > index 9643031a4427a..adf3076b96503 100644 > > > --- a/drivers/net/wireless/ath/ath10k/hw.h > > > +++ b/drivers/net/wireless/ath/ath10k/hw.h > > > @@ -639,6 +639,8 @@ struct ath10k_hw_params { > > > bool use_fw_tx_credits; > > > > > > bool delay_unmap_buffer; > > > + > > > + bool enable_threaded_napi; > > > }; > > > > > > struct htt_resp; > > > diff --git a/drivers/net/wireless/ath/ath10k/snoc.c b/drivers/net/wireless/ath/ath10k/snoc.c > > > index cfcb759a87dea..b94150fb6ef06 100644 > > > --- a/drivers/net/wireless/ath/ath10k/snoc.c > > > +++ b/drivers/net/wireless/ath/ath10k/snoc.c > > > @@ -927,6 +927,9 @@ static int ath10k_snoc_hif_start(struct ath10k *ar) > > > > > > bitmap_clear(ar_snoc->pending_ce_irqs, 0, CE_COUNT_MAX); > > > > > > + if (ar->hw_params.enable_threaded_napi) > > > + dev_set_threaded(&ar->napi_dev, true); > > > + > > > ath10k_core_napi_enable(ar); > > > ath10k_snoc_irq_enable(ar); > > > ath10k_snoc_rx_post(ar); > > > -- > > > 2.39.0.314.g84b9a713c41-goog > > > > > > > > > -- > > This song goes out to all the folk that thought Stadia would work: > > https://www.linkedin.com/posts/dtaht_the-mushroom-song-activity-6981366665607352320-FXtz > > Dave Täht CEO, TekLibre, LLC -- This song goes out to all the folk that thought Stadia would work: https://www.linkedin.com/posts/dtaht_the-mushroom-song-activity-6981366665607352320-FXtz Dave Täht CEO, TekLibre, LLC ^ permalink raw reply [flat|nested] 9+ messages in thread
[parent not found: <CAHb6Lvpta1fJef-M1LasR5zzzudJ2+CNyWwrSo3DU9OoeiFfzA@mail.gmail.com>]
* Re: [Make-wifi-fast] [PATCH] ath10k: snoc: enable threaded napi on WCN3990 [not found] ` <CAHb6Lvpta1fJef-M1LasR5zzzudJ2+CNyWwrSo3DU9OoeiFfzA@mail.gmail.com> @ 2022-12-30 3:44 ` Dave Taht 0 siblings, 0 replies; 9+ messages in thread From: Dave Taht @ 2022-12-30 3:44 UTC (permalink / raw) To: Bob McMahon Cc: Abhishek Kumar, netdev, kvalo, linux-wireless, linux-kernel, ath10k, Eric Dumazet, Make-Wifi-fast, Jakub Kicinski, Paolo Abeni, David S. Miller thx for leaning in bob! (for those of you that don't know, he's the iperf2 maintainer, and if you haven't updated your distro/os/test environment to 2.1.8 that came out in august, yet there's all kinds of nifty new stuff in there: https://sourceforge.net/projects/iperf2 - too much to list, and the -i 1 -e option is just the start of it.... Iperf2's principal flaw is that people think iperf3 is the successor to it, and no, they are very different codebases, with very different features. iperf = iperf2, for most, but not all. On Wed, Dec 28, 2022 at 9:54 PM Bob McMahon <bob.mcmahon@broadcom.com> wrote: > > A bit of a tangent but iperf 2's enhanced option provides sampled RTT and CWND in the interval output. I requires -e. It also provide the connect time, the icwnd, irtt and the mss per the connect. > > [rjmcmahon@rjm-nas ~]$ iperf -c 192.168.1.85 -i 1 -e > ------------------------------------------------------------ > Client connecting to 192.168.1.85, TCP port 5001 with pid 20041 (1 flows) > Write buffer size: 131072 Byte > TOS set to 0x0 (Nagle on) > TCP window size: 16.0 KByte (default) > ------------------------------------------------------------ > [ 1] local 192.168.1.73%eno1 port 38822 connected with 192.168.1.85 port 5001 (sock=3) (icwnd/mss/irtt=14/1448/246) (ct=0.32 ms) on 2022-12-28 21:51:13 (PST) > [ ID] Interval Transfer Bandwidth Write/Err Rtry Cwnd/RTT(var) NetPwr > [ 1] 0.00-1.00 sec 114 MBytes 952 Mbits/sec 908/0 3 353K/1901(59) us 62606 > [ 1] 1.00-2.00 sec 111 MBytes 932 Mbits/sec 889/0 0 354K/2029(115) us 57429 > [ 1] 2.00-3.00 sec 112 MBytes 937 Mbits/sec 894/0 3 354K/2061(84) us 56855 > [ 1] 3.00-4.00 sec 112 MBytes 938 Mbits/sec 895/0 3 354K/2027(115) us 57873 > [ 1] 4.00-5.00 sec 112 MBytes 938 Mbits/sec 895/0 6 354K/2046(68) us 57336 > [ 1] 5.00-6.00 sec 112 MBytes 937 Mbits/sec 894/0 0 374K/2160(109) us 54249 > [ 1] 6.00-7.00 sec 111 MBytes 933 Mbits/sec 890/0 2 374K/2155(115) us 54132 > [ 1] 7.00-8.00 sec 111 MBytes 934 Mbits/sec 891/0 2 374K/2139(120) us 54598 > [ 1] 8.00-9.00 sec 112 MBytes 938 Mbits/sec 895/0 0 374K/2129(126) us 55101 > [ 1] 9.00-10.00 sec 112 MBytes 935 Mbits/sec 892/0 1 374K/2200(102) us 53144 > [ 1] 0.00-10.03 sec 1.09 GBytes 935 Mbits/sec 8944/0 20 374K/4082(4010) us 28632 This is a wonderful new feature, much simpler than relying on packet captures. However! this test result above is on a decent, ethernet, network, where on wifi, or anything bufferbloated, you would see the cwnd and rtt inflate and/or bounce around horribly. > > > Bob > > On Wed, Dec 28, 2022 at 4:49 PM Dave Taht via Make-wifi-fast <make-wifi-fast@lists.bufferbloat.net> wrote: >> >> On Wed, Dec 28, 2022 at 3:53 PM Abhishek Kumar <kuabhs@chromium.org> wrote: >> > >> > Apologies for the late reply, Thanks Dave for your comment. My answer is inline. >> > >> > On Tue, Dec 20, 2022 at 7:10 AM Dave Taht <dave.taht@gmail.com> wrote: >> > > >> > > I am always interested in flent.org tcp_nup, tcp_ndown, and rrul_be >> > > tests on wifi hardware. In AP mode, especially, against a few clients >> > > in rtt_fair on the "ending the anomaly" test suite at the bottom of >> > > this link: https://www.cs.kau.se/tohojo/airtime-fairness/ . Of these, >> > > it's trying to optimize bandwidth more fairly and keep latencies low >> > > when 4 or more stations are trying to transmit (in a world with 16 or >> > > more stations online), that increasingly bothers me the most. I'm >> > > seeing 5+ seconds on some rtt_fair-like tests nowadays. >> > I used testing using iperf and conductive setup and fetched the >> > throughput data(mentioned below). >> > > >> > > I was also seeing huge simultaneous upload vs download disparities on >> > > the latest kernels, on various threads over here: >> > > https://forum.openwrt.org/t/aql-and-the-ath10k-is-lovely/59002 and >> > > more recently here: >> > > https://forum.openwrt.org/t/reducing-multiplexing-latencies-still-further-in-wifi/133605 >> > Interesting, thanks for the pointer and probably the Qualcomm team is >> > aware of it. >> > > >> > > I don't understand why napi with the default budget (64) is even >> > > needed on the ath10k, as a single txop takes a minimum of ~200us, but >> > > perhaps your patch will help. Still, measuring the TCP statistics >> > > in-band would be nice to see. Some new tools are appearing that can do >> > > this, Apple's goresponsiveness, crusader... that are simpler to use >> > > than flent. >> > Here are some of the additional raw data with and without threaded napi: >> > ================================================== >> > udp_rx(Without threaded NAPI) >> > 435.98+-5.16 : Channel 44 >> > 439.06+-0.66 : Channel 157 >> > >> > udp_rx(With threaded NAPI) >> > 509.73+-41.03 : Channel 44 >> > 549.97+-7.62 : Channel 157 >> > =================================================== >> > udp_tx(Without threaded NAPI) >> > 461.31+-0.69 : Channel 44 >> > 461.46+-0.78 : Channel 157 >> > >> > udp_tx(With threaded NAPI) >> > 459.20+-0.77 : Channel 44 >> > 459.78+-1.08 : Channel 157 >> > =================================================== >> > tcp_rx(Without threaded NAPI) >> > 472.63+-2.35 : Channel 44 >> > 469.29+-6.31 : Channel 157 >> > >> > tcp_rx(With threaded NAPI) >> > 498.49+-2.44 : Channel 44 >> > 541.14+-40.65 : Channel 157 >> > =================================================== >> > tcp_tx(Without threaded NAPI) >> > 317.34+-2.37 : Channel 44 >> > 317.01+-2.56 : Channel 157 >> > >> > tcp_tx(With threaded NAPI) >> > 371.34+-2.36 : Channel 44 >> > 376.95+-9.40 : Channel 157 >> >> My concern is primarily with the induced tcp latency on this test. A >> way to check that is to run wireshark on your test client driving the >> test, capture the iperf traffic, and then plot the "Statistics->TCP >> stream statistics for both throughput and rtt. Would it be possible >> for you to do that and put up those plots somewhere? >> >> The worst case test is a tcp bidirectional test which I don't know if >> older iperfs can do. (iperf2 has new bounceback and bidir tests) >> >> Ideally stuff going in either direction, would not look as horrible, >> as it did, back in 2016, documented in this linuxplumbers presentation >> here: https://blog.linuxplumbersconf.org/2016/ocw/system/presentations/3963/original/linuxplumbers_wifi_latency-3Nov.pdf >> and discussed on lwn, here: https://lwn.net/Articles/705884/ >> >> I worry about folk achieving slightly better tcp throughput at the >> expense of clobbering in-tcp-stream latency. Back then we were >> shooting for no more than 40ms extra latency under load on this chip, >> down from (unusable) seconds. Presently elsewhere, on other chips, >> we're getting 8ms with stuff that's not in tree for the ath10k, there >> is a slight cost in single stream throughput but when multiple streams >> are in use, on multiple stations, things like web pages fly, >> irrespective of load. >> >> >> > ==================================================== >> > >> > > >> > > On Tue, Dec 20, 2022 at 12:17 AM Abhishek Kumar <kuabhs@chromium.org> wrote: >> > > > >> > > > NAPI poll can be done in threaded context along with soft irq >> > > > context. Threaded context can be scheduled efficiently, thus >> > > > creating less of bottleneck during Rx processing. This patch is >> > > > to enable threaded NAPI on ath10k driver. >> > > > >> > > > Based on testing, it was observed that on WCN3990, the CPU0 reaches >> > > > 100% utilization when napi runs in softirq context. At the same >> > > > time the other CPUs are at low consumption percentage. This >> > > > does not allow device to reach its maximum throughput potential. >> > > > After enabling threaded napi, CPU load is balanced across all CPUs >> > > > and following improvments were observed: >> > > > - UDP_RX increase by ~22-25% >> > > > - TCP_RX increase by ~15% >> > > > >> > > > Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00696-QCAHLSWMTPL-1 >> > > > Signed-off-by: Abhishek Kumar <kuabhs@chromium.org> >> > > > --- >> > > > >> > > > drivers/net/wireless/ath/ath10k/core.c | 16 ++++++++++++++++ >> > > > drivers/net/wireless/ath/ath10k/hw.h | 2 ++ >> > > > drivers/net/wireless/ath/ath10k/snoc.c | 3 +++ >> > > > 3 files changed, 21 insertions(+) >> > > > >> > > > diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c >> > > > index 5eb131ab916fd..ee4b6ba508c81 100644 >> > > > --- a/drivers/net/wireless/ath/ath10k/core.c >> > > > +++ b/drivers/net/wireless/ath/ath10k/core.c >> > > > @@ -100,6 +100,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA988X_HW_2_0_VERSION, >> > > > @@ -140,6 +141,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA9887_HW_1_0_VERSION, >> > > > @@ -181,6 +183,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA6174_HW_3_2_VERSION, >> > > > @@ -217,6 +220,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA6174_HW_2_1_VERSION, >> > > > @@ -257,6 +261,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA6174_HW_2_1_VERSION, >> > > > @@ -297,6 +302,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA6174_HW_3_0_VERSION, >> > > > @@ -337,6 +343,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA6174_HW_3_2_VERSION, >> > > > @@ -381,6 +388,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA99X0_HW_2_0_DEV_VERSION, >> > > > @@ -427,6 +435,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA9984_HW_1_0_DEV_VERSION, >> > > > @@ -480,6 +489,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA9888_HW_2_0_DEV_VERSION, >> > > > @@ -530,6 +540,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA9377_HW_1_0_DEV_VERSION, >> > > > @@ -570,6 +581,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA9377_HW_1_1_DEV_VERSION, >> > > > @@ -612,6 +624,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA9377_HW_1_1_DEV_VERSION, >> > > > @@ -645,6 +658,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = QCA4019_HW_1_0_DEV_VERSION, >> > > > @@ -692,6 +706,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = false, >> > > > .use_fw_tx_credits = true, >> > > > .delay_unmap_buffer = false, >> > > > + .enable_threaded_napi = false, >> > > > }, >> > > > { >> > > > .id = WCN3990_HW_1_0_DEV_VERSION, >> > > > @@ -725,6 +740,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { >> > > > .hw_restart_disconnect = true, >> > > > .use_fw_tx_credits = false, >> > > > .delay_unmap_buffer = true, >> > > > + .enable_threaded_napi = true, >> > > > }, >> > > > }; >> > > > >> > > > diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h >> > > > index 9643031a4427a..adf3076b96503 100644 >> > > > --- a/drivers/net/wireless/ath/ath10k/hw.h >> > > > +++ b/drivers/net/wireless/ath/ath10k/hw.h >> > > > @@ -639,6 +639,8 @@ struct ath10k_hw_params { >> > > > bool use_fw_tx_credits; >> > > > >> > > > bool delay_unmap_buffer; >> > > > + >> > > > + bool enable_threaded_napi; >> > > > }; >> > > > >> > > > struct htt_resp; >> > > > diff --git a/drivers/net/wireless/ath/ath10k/snoc.c b/drivers/net/wireless/ath/ath10k/snoc.c >> > > > index cfcb759a87dea..b94150fb6ef06 100644 >> > > > --- a/drivers/net/wireless/ath/ath10k/snoc.c >> > > > +++ b/drivers/net/wireless/ath/ath10k/snoc.c >> > > > @@ -927,6 +927,9 @@ static int ath10k_snoc_hif_start(struct ath10k *ar) >> > > > >> > > > bitmap_clear(ar_snoc->pending_ce_irqs, 0, CE_COUNT_MAX); >> > > > >> > > > + if (ar->hw_params.enable_threaded_napi) >> > > > + dev_set_threaded(&ar->napi_dev, true); >> > > > + >> > > > ath10k_core_napi_enable(ar); >> > > > ath10k_snoc_irq_enable(ar); >> > > > ath10k_snoc_rx_post(ar); >> > > > -- >> > > > 2.39.0.314.g84b9a713c41-goog >> > > > >> > > >> > > >> > > -- >> > > This song goes out to all the folk that thought Stadia would work: >> > > https://www.linkedin.com/posts/dtaht_the-mushroom-song-activity-6981366665607352320-FXtz >> > > Dave Täht CEO, TekLibre, LLC >> >> >> >> -- >> This song goes out to all the folk that thought Stadia would work: >> https://www.linkedin.com/posts/dtaht_the-mushroom-song-activity-6981366665607352320-FXtz >> Dave Täht CEO, TekLibre, LLC >> _______________________________________________ >> Make-wifi-fast mailing list >> Make-wifi-fast@lists.bufferbloat.net >> https://lists.bufferbloat.net/listinfo/make-wifi-fast > > > This electronic communication and the information and any files transmitted with it, or attached to it, are confidential and are intended solely for the use of the individual or entity to whom it is addressed and may contain information that is confidential, legally privileged, protected by privacy laws, or otherwise restricted from disclosure to anyone else. If you are not the intended recipient or the person responsible for delivering the e-mail to the intended recipient, you are hereby notified that any use, copying, distributing, dissemination, forwarding, printing, or copying of this e-mail is strictly prohibited. If you received this e-mail in error, please return the e-mail to the sender, delete it from your computer, and destroy any printed copy of it. -- This song goes out to all the folk that thought Stadia would work: https://www.linkedin.com/posts/dtaht_the-mushroom-song-activity-6981366665607352320-FXtz Dave Täht CEO, TekLibre, LLC ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2023-01-27 22:08 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-12-20 7:55 [PATCH] ath10k: snoc: enable threaded napi on WCN3990 Abhishek Kumar
2022-12-20 12:14 ` Manikanta Pubbisetty
2022-12-29 0:01 ` Abhishek Kumar
2023-01-12 10:15 ` Kalle Valo
2023-01-27 22:08 ` Abhishek Kumar
2022-12-20 15:10 ` Dave Taht
2022-12-28 23:53 ` Abhishek Kumar
2022-12-29 0:49 ` Dave Taht
[not found] ` <CAHb6Lvpta1fJef-M1LasR5zzzudJ2+CNyWwrSo3DU9OoeiFfzA@mail.gmail.com>
2022-12-30 3:44 ` [Make-wifi-fast] " Dave Taht
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).