From: Quan Nguyen <quan@os.amperecomputing.com>
To: Joel Stanley <joel@jms.id.au>
Cc: devicetree <devicetree@vger.kernel.org>,
linux-aspeed <linux-aspeed@lists.ozlabs.org>,
Andrew Jeffery <andrew@aj.id.au>,
OpenBMC Maillist <openbmc@lists.ozlabs.org>,
"Thang Q . Nguyen" <thang@os.amperecomputing.com>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Phong Vo <phong@os.amperecomputing.com>,
Rob Herring <robh+dt@kernel.org>,
Open Source Submission <patches@amperecomputing.com>,
Linux ARM <linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH v2 1/3] ARM: dts: aspeed: mtjade: Add some gpios
Date: Mon, 1 Nov 2021 16:25:38 +0700 [thread overview]
Message-ID: <4eb31178-cf05-24cd-6a75-6628689cef25@os.amperecomputing.com> (raw)
In-Reply-To: <87d82a93-cdc2-d95a-4ab9-085ff31c4387@os.amperecomputing.com>
Dear Joel,
I found this patch appears in linux-next tree as in [1], can we expect
the remain two patches in this patchset ([2] and [3]) will be merged soon?
[1]
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?h=next-20211029&id=0b32c1b4071c482f2cf98b717cfc7380423ec619
[2] https://www.spinics.net/lists/kernel/msg4115571.html
[3] https://www.spinics.net/lists/kernel/msg4115572.html
Thanks,
- Quan
On 25/10/2021 11:44, Quan Nguyen wrote:
> On 19/10/2021 13:46, Joel Stanley wrote:
>> On Tue, 19 Oct 2021 at 06:02, Quan Nguyen
>> <quan@os.amperecomputing.com> wrote:
>>>
>>> Add S0_SCP_AUTH_FAIL, S1_SCP_AUTH_FAIL gpios to indicates firmware
>>> authentication fail on each socket.
>>
>> These use the gpio-keys API to expose the GPIOs. I think OpenBMC is
>> moving away from this abstraction, and instead reading the GPIOs with
>> the gpio chardev interface.
>>
> Thanks Joel for the review,
> Yes, will switch to use gpio chardev interface and will remove these
> gpio-keys defined in next version
>
>>>
>>> Add gpio RTC_BAT_SEN_EN to enable RTC battery adc sensor.
>>>
>>> Add BMC_I2C4_O_EN gpio to go high at boot to enable access to I2C4 bus.
>>
>> OpenBMC has started a process to document GPIOs that are exposed to
>> userspace, initially so a common userspace can be used across
>> machines. I like doing it for the additional reason that it provides
>> consistency in the naming.
>>
>> https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md
>>
>>
>> If you could take a look at that document and add your GPIOs where
>> possible, and then update the device tree.
>>
>
> There is on-going discussion about naming of the RTC voltage sensing
> enable gpio pin in [1], So I'd like to address this change later in
> separate patch when this is settled. Hence, I will remove this changes
> in next version.
>
> [1] https://gerrit.openbmc-project.xyz/c/openbmc/docs/+/48018
>
> About the BMC_I2C4_O_EN, this is needed as gpio-hog to make the i2c bus
> accessible at boot time so I will keep this in next version.
> In fact, I'm still a bit of confuse if this pin needs a common name as
> it is just to enable the bus access and does not serve for any
> particular common purpose.
>
> Thanks,
> - Quan
>
>>>
>>> Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
>>> Signed-off-by: Thang Nguyen <thang@os.amperecomputing.com>
>>> ---
>>> v2:
>>> - None
>>>
>>> .../arm/boot/dts/aspeed-bmc-ampere-mtjade.dts | 21 ++++++++++++++++++-
>>> 1 file changed, 20 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
>>> b/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
>>> index 57b0c45a2298..3515d55bd312 100644
>>> --- a/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
>>> +++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
>>> @@ -86,6 +86,18 @@ S0_cpu_fault {
>>> linux,code = <ASPEED_GPIO(J, 1)>;
>>> };
>>>
>>> + S0_scp_auth_fail {
>>> + label = "S0_SCP_AUTH_FAIL";
>>> + gpios = <&gpio ASPEED_GPIO(J, 2)
>>> GPIO_ACTIVE_LOW>;
>>> + linux,code = <ASPEED_GPIO(J, 2)>;
>>> + };
>>> +
>>> + S1_scp_auth_fail {
>>> + label = "S1_SCP_AUTH_FAIL";
>>> + gpios = <&gpio ASPEED_GPIO(Z, 5)
>>> GPIO_ACTIVE_LOW>;
>>> + linux,code = <ASPEED_GPIO(Z, 5)>;
>>> + };
>>> +
>>> S1_overtemp {
>>> label = "S1_OVERTEMP";
>>> gpios = <&gpio ASPEED_GPIO(Z, 6)
>>> GPIO_ACTIVE_LOW>;
>>> @@ -590,7 +602,7 @@ &gpio {
>>> /*Q0-Q7*/ "","","","","","UID_BUTTON","","",
>>> /*R0-R7*/ "","","BMC_EXT_HIGHTEMP_L","OCP_AUX_PWREN",
>>> "OCP_MAIN_PWREN","RESET_BUTTON","","",
>>> - /*S0-S7*/ "","","","","","","","",
>>> + /*S0-S7*/ "","","","","RTC_BAT_SEN_EN","","","",
>>
>> I suggest you create a proposal to call this one
>> battery-voltage-read-enable. I know that some of the IBM machines
>> intend to have this same GPIO.
>>
>>> /*T0-T7*/ "","","","","","","","",
>>> /*U0-U7*/ "","","","","","","","",
>>> /*V0-V7*/ "","","","","","","","",
>>> @@ -604,4 +616,11 @@ &gpio {
>>> "S1_BMC_DDR_ADR","","","","",
>>> /*AC0-AC7*/
>>> "SYS_PWR_GD","","","","","BMC_READY","SLAVE_PRESENT_L",
>>> "BMC_OCP_PG";
>>> +
>>> + i2c4_o_en {
>>> + gpio-hog;
>>> + gpios = <ASPEED_GPIO(Y, 2) GPIO_ACTIVE_HIGH>;
>>> + output-high;
>>> + line-name = "BMC_I2C4_O_EN";
>>> + };
>>> };
>>> --
>>> 2.28.0
>>>
>
next prev parent reply other threads:[~2021-11-01 9:27 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-19 6:01 [PATCH v2 0/3] Update gpios, nvme i2c busses and uefi partition Quan Nguyen
2021-10-19 6:01 ` [PATCH v2 1/3] ARM: dts: aspeed: mtjade: Add some gpios Quan Nguyen
2021-10-19 6:46 ` Joel Stanley
2021-10-19 10:37 ` Thang Nguyen
2021-10-25 4:44 ` Quan Nguyen
2021-11-01 9:25 ` Quan Nguyen [this message]
2021-11-16 5:24 ` Joel Stanley
2021-10-19 6:01 ` [PATCH v2 2/3] ARM: dts: aspeed: mtjade: Add I2C buses for NVMe devices Quan Nguyen
2021-10-19 6:46 ` Joel Stanley
2021-10-19 6:01 ` [PATCH v2 3/3] ARM: dts: aspeed: mtjade: Add uefi partition Quan Nguyen
2021-10-19 6:46 ` Joel Stanley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4eb31178-cf05-24cd-6a75-6628689cef25@os.amperecomputing.com \
--to=quan@os.amperecomputing.com \
--cc=andrew@aj.id.au \
--cc=devicetree@vger.kernel.org \
--cc=joel@jms.id.au \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=linux-kernel@vger.kernel.org \
--cc=openbmc@lists.ozlabs.org \
--cc=patches@amperecomputing.com \
--cc=phong@os.amperecomputing.com \
--cc=robh+dt@kernel.org \
--cc=thang@os.amperecomputing.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).