* [PATCH v3 0/2] Add UFS PHY support for SM6115/4250
@ 2021-08-21 15:56 Iskren Chernev
2021-08-21 15:56 ` [PATCH v3 1/2] dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings Iskren Chernev
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Iskren Chernev @ 2021-08-21 15:56 UTC (permalink / raw)
To: Bjorn Andersson, Vinod Koul
Cc: Andy Gross, Kishon Vijay Abraham I, Rob Herring, devicetree,
linux-arm-msm, linux-kernel, linux-phy, phone-devel,
~postmarketos/upstreaming, Iskren Chernev
The UFS PHY found on SM6115/4250 has a lot of common registers with ufs phy v2,
even though in downstream it is named v3-660. Due to register similarity with
v2, the few extra registers that are needed are added as v2 registers.
The register values/sequences are taken from OnePlus repo [1].
[1] https://github.com/OnePlusOSS/android_kernel_oneplus_sm4250
v1: https://lkml.org/lkml/2021/8/5/235
v2: https://lkml.org/lkml/2021/8/13/889
Changes from v2:
- Suggested by Vinod
- the 6115 registers had a lot in common with v2 registers (and not v3, as
was initially assumed), so those were reused whenever possible, and new
regs were added along other v2 registers.
Changes from v1:
- Suggested by Vinod
- removed v3-660 constants for regs with same name and value as v3 regs
Iskren Chernev (2):
dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings
phy: qcom-qmp: Add support for SM6115 UFS phy
.../devicetree/bindings/phy/qcom,qmp-phy.yaml | 1 +
drivers/phy/qualcomm/phy-qcom-qmp.c | 124 ++++++++++++++++++
drivers/phy/qualcomm/phy-qcom-qmp.h | 18 +++
3 files changed, 143 insertions(+)
base-commit: 86ed57fd8c93fdfaabb4f58e78455180fa7d8a84
--
2.32.0
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v3 1/2] dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings
2021-08-21 15:56 [PATCH v3 0/2] Add UFS PHY support for SM6115/4250 Iskren Chernev
@ 2021-08-21 15:56 ` Iskren Chernev
2021-08-21 15:56 ` [PATCH v3 2/2] phy: qcom-qmp: Add support for SM6115 UFS phy Iskren Chernev
2021-08-23 5:43 ` [PATCH v3 0/2] Add UFS PHY support for SM6115/4250 Vinod Koul
2 siblings, 0 replies; 4+ messages in thread
From: Iskren Chernev @ 2021-08-21 15:56 UTC (permalink / raw)
To: Bjorn Andersson, Vinod Koul
Cc: Andy Gross, Kishon Vijay Abraham I, Rob Herring, devicetree,
linux-arm-msm, linux-kernel, linux-phy, phone-devel,
~postmarketos/upstreaming, Iskren Chernev, Rob Herring,
Manu Gautam
Add the compatible strings for the UFS PHY found on SM4250/6115 SoC.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
index 47d99001d2dd..75be5650a198 100644
--- a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
@@ -36,6 +36,7 @@ properties:
- qcom,sdm845-qmp-ufs-phy
- qcom,sdm845-qmp-usb3-phy
- qcom,sdm845-qmp-usb3-uni-phy
+ - qcom,sm6115-qmp-ufs-phy
- qcom,sm8150-qmp-ufs-phy
- qcom,sm8150-qmp-usb3-phy
- qcom,sm8150-qmp-usb3-uni-phy
--
2.32.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v3 2/2] phy: qcom-qmp: Add support for SM6115 UFS phy
2021-08-21 15:56 [PATCH v3 0/2] Add UFS PHY support for SM6115/4250 Iskren Chernev
2021-08-21 15:56 ` [PATCH v3 1/2] dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings Iskren Chernev
@ 2021-08-21 15:56 ` Iskren Chernev
2021-08-23 5:43 ` [PATCH v3 0/2] Add UFS PHY support for SM6115/4250 Vinod Koul
2 siblings, 0 replies; 4+ messages in thread
From: Iskren Chernev @ 2021-08-21 15:56 UTC (permalink / raw)
To: Bjorn Andersson, Vinod Koul
Cc: Andy Gross, Kishon Vijay Abraham I, Rob Herring, devicetree,
linux-arm-msm, linux-kernel, linux-phy, phone-devel,
~postmarketos/upstreaming, Iskren Chernev
Add the tables and constants for init sequences for UFS QMP phy found in
SM4250/6115 SoC. The phy is a variation of the v2 phy, but is mistakenly
labeled as v3-660 in downstream sources.
QSERDES COM, RX, TX registers match fully existing v2 registers, with
a few additions. PCS registers don't have much in common, but there are
no clashes with existing ones so new registers were added to existing v2
PCS pack.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 124 ++++++++++++++++++++++++++++
drivers/phy/qualcomm/phy-qcom-qmp.h | 18 ++++
2 files changed, 142 insertions(+)
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index a8c4368f984b..f14032170b1c 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -234,6 +234,11 @@ static const unsigned int sdm845_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
[QPHY_PCS_READY_STATUS] = 0x160,
};
+static const unsigned int sm6115_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
+ [QPHY_START_CTRL] = 0x00,
+ [QPHY_PCS_READY_STATUS] = 0x168,
+};
+
static const unsigned int sm8250_pcie_regs_layout[QPHY_LAYOUT_SIZE] = {
[QPHY_SW_RESET] = 0x00,
[QPHY_START_CTRL] = 0x44,
@@ -1329,6 +1334,97 @@ static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_pcs_tbl[] = {
QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG2, 0x60),
};
+static const struct qmp_phy_init_tbl sm6115_ufsphy_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x0e),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x30),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV_MODE1, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_EN, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_CTRL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_RESETSM_CNTRL, 0x20),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_CFG, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER1, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER2, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x05),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE1_MODE0, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE2_MODE0, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE1, 0x98),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE1, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE1, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE1, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE1, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE1_MODE1, 0xd6),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE2_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE1, 0x32),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE1, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_INITVAL1, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_INITVAL2, 0x00),
+
+ /* Rate B */
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x44),
+};
+
+static const struct qmp_phy_init_tbl sm6115_ufsphy_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
+ QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06),
+};
+
+static const struct qmp_phy_init_tbl sm6115_ufsphy_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x24),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_CNTRL, 0x0F),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_INTERFACE_MODE, 0x40),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x1E),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0B),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_TERM_BW, 0x5B),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_GAIN1_LSB, 0xFF),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_GAIN1_MSB, 0x3F),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_GAIN2_LSB, 0xFF),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_GAIN2_MSB, 0x3F),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0D),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SVS_SO_GAIN_HALF, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SVS_SO_GAIN_QUARTER, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SVS_SO_GAIN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x5B),
+};
+
+static const struct qmp_phy_init_tbl sm6115_ufsphy_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_RX_PWM_GEAR_BAND, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_RX_SIGDET_CTRL2, 0x6d),
+ QMP_PHY_INIT_CFG(QPHY_TX_LARGE_AMP_DRV_LVL, 0x0f),
+ QMP_PHY_INIT_CFG(QPHY_TX_SMALL_AMP_DRV_LVL, 0x02),
+ QMP_PHY_INIT_CFG(QPHY_RX_MIN_STALL_NOCONFIG_TIME_CAP, 0x28),
+ QMP_PHY_INIT_CFG(QPHY_RX_SYM_RESYNC_CTRL, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_TX_LARGE_AMP_POST_EMP_LVL, 0x12),
+ QMP_PHY_INIT_CFG(QPHY_TX_SMALL_AMP_POST_EMP_LVL, 0x0f),
+ QMP_PHY_INIT_CFG(QPHY_RX_MIN_HIBERN8_TIME, 0x9a), /* 8 us */
+};
+
static const struct qmp_phy_init_tbl sdm845_ufsphy_serdes_tbl[] = {
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x04),
@@ -3396,6 +3492,31 @@ static const struct qmp_phy_cfg sdm845_ufsphy_cfg = {
.no_pcs_sw_reset = true,
};
+static const struct qmp_phy_cfg sm6115_ufsphy_cfg = {
+ .type = PHY_TYPE_UFS,
+ .nlanes = 1,
+
+ .serdes_tbl = sm6115_ufsphy_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(sm6115_ufsphy_serdes_tbl),
+ .tx_tbl = sm6115_ufsphy_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(sm6115_ufsphy_tx_tbl),
+ .rx_tbl = sm6115_ufsphy_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(sm6115_ufsphy_rx_tbl),
+ .pcs_tbl = sm6115_ufsphy_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(sm6115_ufsphy_pcs_tbl),
+ .clk_list = sdm845_ufs_phy_clk_l,
+ .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
+ .regs = sm6115_ufsphy_regs_layout,
+
+ .start_ctrl = SERDES_START,
+ .pwrdn_ctrl = SW_PWRDN,
+
+ .is_dual_lane_phy = false,
+ .no_pcs_sw_reset = true,
+};
+
static const struct qmp_phy_cfg msm8998_pciephy_cfg = {
.type = PHY_TYPE_PCIE,
.nlanes = 1,
@@ -5444,6 +5565,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
}, {
.compatible = "qcom,msm8998-qmp-usb3-phy",
.data = &msm8998_usb3phy_cfg,
+ }, {
+ .compatible = "qcom,sm6115-qmp-ufs-phy",
+ .data = &sm6115_ufsphy_cfg,
}, {
.compatible = "qcom,sm8150-qmp-ufs-phy",
.data = &sm8150_ufsphy_cfg,
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index 6592b58b13f6..bebeac2c091c 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -191,6 +191,8 @@
#define QSERDES_COM_VCO_TUNE2_MODE0 0x130
#define QSERDES_COM_VCO_TUNE1_MODE1 0x134
#define QSERDES_COM_VCO_TUNE2_MODE1 0x138
+#define QSERDES_COM_VCO_TUNE_INITVAL1 0x13c
+#define QSERDES_COM_VCO_TUNE_INITVAL2 0x140
#define QSERDES_COM_VCO_TUNE_TIMER1 0x144
#define QSERDES_COM_VCO_TUNE_TIMER2 0x148
#define QSERDES_COM_BG_CTRL 0x170
@@ -220,6 +222,10 @@
/* Only for QMP V2 PHY - RX registers */
#define QSERDES_RX_UCDR_SO_GAIN_HALF 0x010
#define QSERDES_RX_UCDR_SO_GAIN 0x01c
+#define QSERDES_RX_UCDR_SVS_SO_GAIN_HALF 0x030
+#define QSERDES_RX_UCDR_SVS_SO_GAIN_QUARTER 0x034
+#define QSERDES_RX_UCDR_SVS_SO_GAIN_EIGHTH 0x038
+#define QSERDES_RX_UCDR_SVS_SO_GAIN 0x03c
#define QSERDES_RX_UCDR_FASTLOCK_FO_GAIN 0x040
#define QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE 0x048
#define QSERDES_RX_RX_TERM_BW 0x090
@@ -243,6 +249,10 @@
#define QPHY_POWER_DOWN_CONTROL 0x04
#define QPHY_TXDEEMPH_M6DB_V0 0x24
#define QPHY_TXDEEMPH_M3P5DB_V0 0x28
+#define QPHY_TX_LARGE_AMP_DRV_LVL 0x34
+#define QPHY_TX_LARGE_AMP_POST_EMP_LVL 0x38
+#define QPHY_TX_SMALL_AMP_DRV_LVL 0x3c
+#define QPHY_TX_SMALL_AMP_POST_EMP_LVL 0x40
#define QPHY_ENDPOINT_REFCLK_DRIVE 0x54
#define QPHY_RX_IDLE_DTCT_CNTRL 0x58
#define QPHY_POWER_STATE_CONFIG1 0x60
@@ -253,6 +263,11 @@
#define QPHY_LOCK_DETECT_CONFIG3 0x88
#define QPHY_PWRUP_RESET_DLY_TIME_AUXCLK 0xa0
#define QPHY_LP_WAKEUP_DLY_TIME_AUXCLK 0xa4
+#define QPHY_RX_MIN_STALL_NOCONFIG_TIME_CAP 0xcc
+#define QPHY_RX_SYM_RESYNC_CTRL 0x13c
+#define QPHY_RX_MIN_HIBERN8_TIME 0x140
+#define QPHY_RX_SIGDET_CTRL2 0x148
+#define QPHY_RX_PWM_GEAR_BAND 0x154
#define QPHY_PLL_LOCK_CHK_DLY_TIME_AUXCLK_LSB 0x1A8
#define QPHY_OSC_DTCT_ACTIONS 0x1AC
#define QPHY_RX_SIGDET_LVL 0x1D8
@@ -280,6 +295,8 @@
#define QSERDES_V3_COM_SSC_PER2 0x020
#define QSERDES_V3_COM_SSC_STEP_SIZE1 0x024
#define QSERDES_V3_COM_SSC_STEP_SIZE2 0x028
+#define QSERDES_V3_COM_POST_DIV 0x02c
+#define QSERDES_V3_COM_POST_DIV_MUX 0x030
#define QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN 0x034
# define QSERDES_V3_COM_BIAS_EN 0x0001
# define QSERDES_V3_COM_BIAS_EN_MUX 0x0002
@@ -291,6 +308,7 @@
#define QSERDES_V3_COM_CLK_ENABLE1 0x038
#define QSERDES_V3_COM_SYS_CLK_CTRL 0x03c
#define QSERDES_V3_COM_SYSCLK_BUF_ENABLE 0x040
+#define QSERDES_V3_COM_PLL_EN 0x044
#define QSERDES_V3_COM_PLL_IVCO 0x048
#define QSERDES_V3_COM_LOCK_CMP1_MODE0 0x098
#define QSERDES_V3_COM_LOCK_CMP2_MODE0 0x09c
--
2.32.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH v3 0/2] Add UFS PHY support for SM6115/4250
2021-08-21 15:56 [PATCH v3 0/2] Add UFS PHY support for SM6115/4250 Iskren Chernev
2021-08-21 15:56 ` [PATCH v3 1/2] dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings Iskren Chernev
2021-08-21 15:56 ` [PATCH v3 2/2] phy: qcom-qmp: Add support for SM6115 UFS phy Iskren Chernev
@ 2021-08-23 5:43 ` Vinod Koul
2 siblings, 0 replies; 4+ messages in thread
From: Vinod Koul @ 2021-08-23 5:43 UTC (permalink / raw)
To: Iskren Chernev
Cc: Bjorn Andersson, Andy Gross, Kishon Vijay Abraham I, Rob Herring,
devicetree, linux-arm-msm, linux-kernel, linux-phy, phone-devel,
~postmarketos/upstreaming
On 21-08-21, 18:56, Iskren Chernev wrote:
> The UFS PHY found on SM6115/4250 has a lot of common registers with ufs phy v2,
> even though in downstream it is named v3-660. Due to register similarity with
> v2, the few extra registers that are needed are added as v2 registers.
>
> The register values/sequences are taken from OnePlus repo [1].
This looks very good, thanks for cleaning it up
Applied now
--
~Vinod
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2021-08-23 5:43 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-08-21 15:56 [PATCH v3 0/2] Add UFS PHY support for SM6115/4250 Iskren Chernev
2021-08-21 15:56 ` [PATCH v3 1/2] dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings Iskren Chernev
2021-08-21 15:56 ` [PATCH v3 2/2] phy: qcom-qmp: Add support for SM6115 UFS phy Iskren Chernev
2021-08-23 5:43 ` [PATCH v3 0/2] Add UFS PHY support for SM6115/4250 Vinod Koul
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).