* [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform
@ 2021-09-09 12:37 AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 2/7] arm64: dts: qcom: msm8998-xperia: Add RMI4 touchscreen support AngeloGioacchino Del Regno
` (6 more replies)
0 siblings, 7 replies; 8+ messages in thread
From: AngeloGioacchino Del Regno @ 2021-09-09 12:37 UTC (permalink / raw)
To: bjorn.andersson
Cc: agross, robh+dt, linux-arm-msm, devicetree, linux-kernel,
konrad.dybcio, marijn.suijten, martin.botka,
~postmarketos/upstreaming, phone-devel, paul.bouchara,
AngeloGioacchino Del Regno
This commit introduces support for the Sony Yoshino platform, using
the MSM8998 SoC, including:
- Sony Xperia XZ1 (codename Poplar),
- Sony Xperia XZ1 Compact (codename Lilac),
- Sony Xperia XZ Premium (codename Maple).
All of the three aforementioned smartphones are sharing a 99%
equal board configuration, with very small differences between
each other, which is the reason for the introduction of a common
msm8998-sony-xperia-yoshino DT.
This base configuration includes regulators and project-wide pin
configurations and it's made to boot to a serial console.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/Makefile | 3 +
.../msm8998-sony-xperia-yoshino-lilac.dts | 19 +
.../msm8998-sony-xperia-yoshino-maple.dts | 43 ++
.../msm8998-sony-xperia-yoshino-poplar.dts | 24 +
.../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 475 ++++++++++++++++++
5 files changed, 564 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 70516508be56..8a0b558c3065 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -39,6 +39,9 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-lenovo-miix-630.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-cheeseburger.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-lilac.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
new file mode 100644
index 000000000000..550de79e0151
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "msm8998-sony-xperia-yoshino.dtsi"
+
+/ {
+ model = "Sony Xperia XZ1 Compact";
+ compatible = "sony,xperia-lilac", "qcom,msm8998";
+};
+
+&vreg_l22a_2p85 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
new file mode 100644
index 000000000000..35a6cdb55aec
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "msm8998-sony-xperia-yoshino.dtsi"
+
+/ {
+ model = "Sony Xperia XZ Premium";
+ compatible = "sony,xperia-maple", "qcom,msm8998";
+
+ disp_dvdd_vreg: disp-dvdd-vreg {
+ compatible = "regulator-fixed";
+ regulator-name = "disp_dvdd_en";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ startup-delay-us = <0>;
+ enable-active-high;
+ gpio = <&pmi8998_gpio 10 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&disp_dvdd_en>;
+ };
+};
+
+&pmi8998_gpio {
+ disp_dvdd_en: disp-dvdd-en-active {
+ pins = "gpio10";
+ function = "normal";
+ bias-disable;
+ drive-push-pull;
+ output-high;
+ power-source = <0>;
+ qcom,drive-strength = <1>;
+ };
+};
+
+&vreg_l22a_2p85 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
new file mode 100644
index 000000000000..6255004b9a09
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "msm8998-sony-xperia-yoshino.dtsi"
+
+/ {
+ model = "Sony Xperia XZ1";
+ compatible = "sony,xperia-poplar", "qcom,msm8998";
+};
+
+&vreg_l18a_2p85 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+};
+
+&vreg_l22a_2p85 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
new file mode 100644
index 000000000000..98d23f8b93ac
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -0,0 +1,475 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@somainline.org>
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include "msm8998.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+
+/ {
+ /* required for bootloader to select correct board */
+ qcom,msm-id = <0x124 0x20000>, <0x124 0x20001>; /* 8998v2, v2.1 */
+ qcom,board-id = <8 0>;
+
+ board_vbat: vbat-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VBAT";
+
+ regulator-min-microvolt = <4000000>;
+ regulator-max-microvolt = <4000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ input-name = "gpio-keys";
+ label = "Side buttons";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vol_down_pin_a>, <&cam_focus_pin_a>,
+ <&cam_snapshot_pin_a>;
+ vol-down {
+ label = "Volume Down";
+ gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_KEY>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ gpio-key,wakeup;
+ debounce-interval = <15>;
+ };
+
+ camera-snapshot {
+ label = "Camera Snapshot";
+ gpios = <&pm8998_gpio 7 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_KEY>;
+ linux,code = <KEY_CAMERA>;
+ debounce-interval = <15>;
+ };
+
+ camera-focus {
+ label = "Camera Focus";
+ gpios = <&pm8998_gpio 8 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_KEY>;
+ linux,code = <KEY_CAMERA_FOCUS>;
+ debounce-interval = <15>;
+ };
+ };
+
+ gpio-hall-sensor {
+ compatible = "gpio-keys";
+ input-name = "hall-sensors";
+ label = "Hall sensors";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hall_sensor0_default>;
+
+ hall-sensor0 {
+ label = "Cover Hall Sensor";
+ gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ gpio-key,wakeup;
+ debounce-interval = <30>;
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ hyp_mem: memory@85800000 {
+ reg = <0x0 0x85800000 0x0 0x3700000>;
+ no-map;
+ };
+
+ cont_splash_mem: memory@9d400000 {
+ reg = <0x0 0x9d400000 0x0 0x2400000>;
+ no-map;
+ };
+
+ zap_shader_region: memory@f6400000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0xf6400000 0x0 0x2000>;
+ no-map;
+ };
+
+ adsp_region: memory@fe000000 {
+ reg = <0x0 0xfe000000 0x0 0x800000>;
+ no-map;
+ };
+
+ qseecom_region: memory@fe800000 {
+ reg = <0x0 0xfe800000 0x0 0x1400000>;
+ no-map;
+ };
+
+ ramoops@ffc00000 {
+ compatible = "ramoops";
+ reg = <0x0 0xffc00000 0x0 0x100000>;
+ record-size = <0x10000>;
+ console-size = <0x60000>;
+ ftrace-size = <0x10000>;
+ pmsg-size = <0x20000>;
+ ecc-size = <16>;
+ };
+ };
+};
+
+&blsp2_uart1 {
+ status = "okay";
+};
+
+&mmcc {
+ status = "ok";
+};
+
+&mmss_smmu {
+ status = "ok";
+};
+
+&pm8005_lsid1 {
+ pm8005-regulators {
+ compatible = "qcom,pm8005-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+
+ /* VDD_GFX supply */
+ pm8005_s1: s1 {
+ regulator-min-microvolt = <524000>;
+ regulator-max-microvolt = <1088000>;
+ regulator-enable-ramp-delay = <500>;
+ regulator-always-on;
+ };
+ };
+};
+
+&pm8998_gpio {
+ vol_down_pin_a: vol-down-active {
+ pins = "gpio5";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ bias-pull-up;
+ input-enable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+
+ cam_focus_pin_a: cam-focus-btn-active {
+ pins = "gpio7";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ bias-pull-up;
+ input-enable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+
+ cam_snapshot_pin_a: cam-snapshot-btn-active {
+ pins = "gpio8";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ bias-pull-up;
+ input-enable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+};
+
+&pm8998_pon {
+ resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+};
+
+&qusb2phy {
+ status = "okay";
+
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&rpm_requests {
+ pm8998-regulators {
+ compatible = "qcom,rpm-pm8998-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+ vdd_s2-supply = <&vph_pwr>;
+ vdd_s3-supply = <&vph_pwr>;
+ vdd_s4-supply = <&vph_pwr>;
+ vdd_s5-supply = <&vph_pwr>;
+ vdd_s6-supply = <&vph_pwr>;
+ vdd_s7-supply = <&vph_pwr>;
+ vdd_s8-supply = <&vph_pwr>;
+ vdd_s9-supply = <&vph_pwr>;
+ vdd_s10-supply = <&vph_pwr>;
+ vdd_s11-supply = <&vph_pwr>;
+ vdd_s12-supply = <&vph_pwr>;
+ vdd_s13-supply = <&vph_pwr>;
+ vdd_l1_l27-supply = <&vreg_s7a_1p025>;
+ vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
+ vdd_l3_l11-supply = <&vreg_s7a_1p025>;
+ vdd_l4_l5-supply = <&vreg_s7a_1p025>;
+ vdd_l6-supply = <&vreg_s5a_2p04>;
+ vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
+ vdd_l9-supply = <&vreg_bob>;
+ vdd_l10_l23_l25-supply = <&vreg_bob>;
+ vdd_l13_l19_l21-supply = <&vreg_bob>;
+ vdd_l16_l28-supply = <&vreg_bob>;
+ vdd_l18_l22-supply = <&vreg_bob>;
+ vdd_l20_l24-supply = <&vreg_bob>;
+ vdd_l26-supply = <&vreg_s3a_1p35>;
+ vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+ vreg_s3a_1p35: s3 {
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+ vreg_s4a_1p8: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-system-load = <100000>;
+ regulator-allow-set-load;
+ };
+ vreg_s5a_2p04: s5 {
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2032000>;
+ };
+ vreg_s7a_1p025: s7 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1028000>;
+ };
+ vreg_l1a_0p875: l1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-system-load = <73400>;
+ regulator-allow-set-load;
+ };
+ vreg_l2a_1p2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-system-load = <12560>;
+ regulator-allow-set-load;
+ };
+ vreg_l3a_1p0: l3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+ vreg_l5a_0p8: l5 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ };
+ vreg_l6a_1p8: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l7a_1p8: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l8a_1p2: l8 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+ vreg_l9a_1p8: l9 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ };
+ vreg_l10a_1p8: l10 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ };
+ vreg_l11a_1p0: l11 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+ vreg_l12a_1p8: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l13a_2p95: l13 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-allow-set-load;
+ };
+ vreg_l14a_1p85: l14 {
+ regulator-min-microvolt = <1848000>;
+ regulator-max-microvolt = <1856000>;
+ regulator-system-load = <32000>;
+ regulator-allow-set-load;
+ };
+ vreg_l15a_1p8: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l16a_2p7: l16 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+ };
+ vreg_l17a_1p3: l17 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ };
+ vreg_l18a_2p85: l18 {};
+ vreg_l19a_2p7: l19 {
+ regulator-min-microvolt = <2696000>;
+ regulator-max-microvolt = <2704000>;
+ };
+ vreg_l20a_2p95: l20 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-system-load = <10000>;
+ regulator-allow-set-load;
+ };
+ vreg_l21a_2p95: l21 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-system-load = <800000>;
+ regulator-allow-set-load;
+ };
+ vreg_l22a_2p85: l22 { };
+ vreg_l23a_3p3: l23 {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3312000>;
+ };
+ vreg_l24a_3p075: l24 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3088000>;
+ };
+ vreg_l25a_3p3: l25 {
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3312000>;
+ };
+ vreg_l26a_1p2: l26 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-allow-set-load;
+ };
+ vreg_l28_3p0: l28 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+ vreg_lvs1a_1p8: lvs1 { };
+ vreg_lvs2a_1p8: lvs2 { };
+ };
+
+ pmi8998-regulators {
+ compatible = "qcom,rpm-pmi8998-regulators";
+
+ vdd_bob-supply = <&vph_pwr>;
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3600000>;
+ };
+ };
+};
+
+&sdhc2 {
+ status = "okay";
+ cd-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
+
+ vmmc-supply = <&vreg_l21a_2p95>;
+ vqmmc-supply = <&vreg_l13a_2p95>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ mdp_vsync_n: mdp-vsync-n {
+ pins = "gpio10";
+ function = "mdp_vsync_a";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ nfc_ven: nfc-ven {
+ pins = "gpio12";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ output-low;
+ };
+
+ msm_mclk0_default: msm-mclk0-active {
+ pins = "gpio13";
+ function = "cam_mclk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ msm_mclk1_default: msm-mclk1-active {
+ pins = "gpio14";
+ function = "cam_mclk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ cci0_default: cci0-default {
+ pins = "gpio18", "gpio19";
+ function = "cci_i2c";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cci1_default: cci1-default {
+ pins = "gpio19", "gpio20";
+ function = "cci_i2c";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ hall_sensor0_default: acc-cover-open {
+ pins = "gpio124";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ input-enable;
+ };
+};
+
+/*
+ * WARNING:
+ * Disable UFS until card quirks are in to avoid unrecoverable hard-brick
+ * that would happen as soon as the UFS card gets probed as, without the
+ * required quirks, the bootloader will be erased right after card probe.
+ */
+&ufshc {
+ status = "disabled";
+};
+
+&ufsphy {
+ status = "disabled";
+};
+
+&usb3 {
+ status = "okay";
+};
+
+&usb3_dwc3 {
+ /* Force to peripheral until we have Type-C hooked up */
+ dr_mode = "peripheral";
+};
+
+&usb3phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l2a_1p2>;
+};
--
2.32.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 2/7] arm64: dts: qcom: msm8998-xperia: Add RMI4 touchscreen support
2021-09-09 12:37 [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform AngeloGioacchino Del Regno
@ 2021-09-09 12:37 ` AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 3/7] arm64: dts: qcom: msm8998-xperia: Add support for wcn3990 Bluetooth AngeloGioacchino Del Regno
` (5 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: AngeloGioacchino Del Regno @ 2021-09-09 12:37 UTC (permalink / raw)
To: bjorn.andersson
Cc: agross, robh+dt, linux-arm-msm, devicetree, linux-kernel,
konrad.dybcio, marijn.suijten, martin.botka,
~postmarketos/upstreaming, phone-devel, paul.bouchara,
AngeloGioacchino Del Regno
All of the devices in the Sony Yoshino platform are using a Synaptics
RMI4-compatible touch IC with identical pins and supplies: enable the
I2C-5 bus and add the rmi4-i2c node along with the required pin
configurations.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
---
.../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 60 +++++++++++++++++++
1 file changed, 60 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index 98d23f8b93ac..8bbff6e80b7f 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -30,6 +30,15 @@ board_vbat: vbat-regulator {
regulator-boot-on;
};
+ touch_vddio_vreg: touch-vddio-vreg {
+ compatible = "regulator-fixed";
+ regulator-name = "touch_vddio_vreg";
+ startup-delay-us = <10000>;
+ gpio = <&tlmm 133 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_vddio_en>;
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -130,6 +139,42 @@ ramoops@ffc00000 {
};
};
+&blsp1_i2c5 {
+ status = "okay";
+ clock-frequency = <355000>;
+
+ touchscreen@2c {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x2c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_int_n>;
+
+ vdd-supply = <&vreg_l28_3p0>;
+ vio-supply = <&touch_vddio_vreg>;
+
+ syna,reset-delay-ms = <220>;
+ syna,startup-delay-ms = <1000>;
+
+ rmi4-f01@1 {
+ reg = <0x01>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f11@11 {
+ reg = <0x11>;
+ syna,sensor-type = <1>;
+ };
+ };
+};
+
+&blsp1_i2c5_sleep {
+ bias-disable;
+};
+
&blsp2_uart1 {
status = "okay";
};
@@ -442,6 +487,21 @@ hall_sensor0_default: acc-cover-open {
drive-strength = <2>;
input-enable;
};
+
+ ts_int_n: ts-int-n {
+ pins = "gpio125";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ ts_vddio_en: ts-vddio-en-default {
+ pins = "gpio133";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ output-low;
+ };
};
/*
--
2.32.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 3/7] arm64: dts: qcom: msm8998-xperia: Add support for wcn3990 Bluetooth
2021-09-09 12:37 [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 2/7] arm64: dts: qcom: msm8998-xperia: Add RMI4 touchscreen support AngeloGioacchino Del Regno
@ 2021-09-09 12:37 ` AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 4/7] arm64: dts: qcom: msm8998-xperia: Add support for gpio vibrator AngeloGioacchino Del Regno
` (4 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: AngeloGioacchino Del Regno @ 2021-09-09 12:37 UTC (permalink / raw)
To: bjorn.andersson
Cc: agross, robh+dt, linux-arm-msm, devicetree, linux-kernel,
konrad.dybcio, marijn.suijten, martin.botka,
~postmarketos/upstreaming, phone-devel, paul.bouchara,
AngeloGioacchino Del Regno
This platform uses the WCN3990 Bluetooth chip, reachable on UART-3.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
---
.../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index 8bbff6e80b7f..cfd61c399b02 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -175,6 +175,22 @@ &blsp1_i2c5_sleep {
bias-disable;
};
+&blsp1_uart3 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3990-bt";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l17a_1p3>;
+ vddch0-supply = <&vreg_l25a_3p3>;
+ max-speed = <3200000>;
+
+ clocks = <&rpmcc RPM_SMD_RF_CLK2_PIN>;
+ };
+};
+
&blsp2_uart1 {
status = "okay";
};
--
2.32.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 4/7] arm64: dts: qcom: msm8998-xperia: Add support for gpio vibrator
2021-09-09 12:37 [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 2/7] arm64: dts: qcom: msm8998-xperia: Add RMI4 touchscreen support AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 3/7] arm64: dts: qcom: msm8998-xperia: Add support for wcn3990 Bluetooth AngeloGioacchino Del Regno
@ 2021-09-09 12:37 ` AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 5/7] arm64: dts: qcom: msm8998-xperia: Configure display boost regulators AngeloGioacchino Del Regno
` (3 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: AngeloGioacchino Del Regno @ 2021-09-09 12:37 UTC (permalink / raw)
To: bjorn.andersson
Cc: agross, robh+dt, linux-arm-msm, devicetree, linux-kernel,
konrad.dybcio, marijn.suijten, martin.botka,
~postmarketos/upstreaming, phone-devel, paul.bouchara,
AngeloGioacchino Del Regno
All smartphones in the Sony Yoshino platforms have got a simple
vibrator hooked to a GPIO: add support for that and add its own
pin configuration.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
---
.../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index cfd61c399b02..798f2d8a8237 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -137,6 +137,13 @@ ramoops@ffc00000 {
ecc-size = <16>;
};
};
+
+ vibrator {
+ compatible = "gpio-vibrator";
+ enable-gpios = <&pmi8998_gpio 5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vib_default>;
+ };
};
&blsp1_i2c5 {
@@ -245,6 +252,18 @@ cam_snapshot_pin_a: cam-snapshot-btn-active {
};
};
+&pmi8998_gpio {
+ vib_default: vib-en {
+ pins = "gpio5";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ bias-disable;
+ drive-push-pull;
+ output-low;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <0>;
+ };
+};
+
&pm8998_pon {
resin {
compatible = "qcom,pm8941-resin";
--
2.32.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 5/7] arm64: dts: qcom: msm8998-xperia: Configure display boost regulators
2021-09-09 12:37 [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform AngeloGioacchino Del Regno
` (2 preceding siblings ...)
2021-09-09 12:37 ` [PATCH v2 4/7] arm64: dts: qcom: msm8998-xperia: Add support for gpio vibrator AngeloGioacchino Del Regno
@ 2021-09-09 12:37 ` AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 6/7] arm64: dts: qcom: msm8998-xperia: Add camera regulators AngeloGioacchino Del Regno
` (2 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: AngeloGioacchino Del Regno @ 2021-09-09 12:37 UTC (permalink / raw)
To: bjorn.andersson
Cc: agross, robh+dt, linux-arm-msm, devicetree, linux-kernel,
konrad.dybcio, marijn.suijten, martin.botka,
~postmarketos/upstreaming, phone-devel, paul.bouchara,
AngeloGioacchino Del Regno
Add configuration for the LAB and IBB regulators (in boost mode):
this platform has smartphones with three different display sizes,
hence different displays requiring different voltage.
The common configuration parameters have been put in the common
device-tree, while specific voltage specs and soft-start-us are
variant specific, so they have been put into the machine specific
dts file.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
---
.../msm8998-sony-xperia-yoshino-lilac.dts | 11 ++++++++
.../msm8998-sony-xperia-yoshino-maple.dts | 11 ++++++++
.../msm8998-sony-xperia-yoshino-poplar.dts | 11 ++++++++
.../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 25 +++++++++++++++++++
4 files changed, 58 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
index 550de79e0151..0de919357de4 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
@@ -13,6 +13,17 @@ / {
compatible = "sony,xperia-lilac", "qcom,msm8998";
};
+&ibb {
+ regulator-min-microvolt = <5500000>;
+ regulator-max-microvolt = <5500000>;
+};
+
+&lab {
+ regulator-min-microvolt = <5500000>;
+ regulator-max-microvolt = <5500000>;
+ qcom,soft-start-us = <800>;
+};
+
&vreg_l22a_2p85 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
index 35a6cdb55aec..87115d648cef 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
@@ -25,6 +25,17 @@ disp_dvdd_vreg: disp-dvdd-vreg {
};
};
+&ibb {
+ regulator-min-microvolt = <5600000>;
+ regulator-max-microvolt = <5600000>;
+};
+
+&lab {
+ regulator-min-microvolt = <5800000>;
+ regulator-max-microvolt = <5800000>;
+ qcom,soft-start-us = <200>;
+};
+
&pmi8998_gpio {
disp_dvdd_en: disp-dvdd-en-active {
pins = "gpio10";
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
index 6255004b9a09..9fa3583c951b 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
@@ -13,6 +13,17 @@ / {
compatible = "sony,xperia-poplar", "qcom,msm8998";
};
+&ibb {
+ regulator-min-microvolt = <5600000>;
+ regulator-max-microvolt = <5600000>;
+};
+
+&lab {
+ regulator-min-microvolt = <5600000>;
+ regulator-max-microvolt = <5600000>;
+ qcom,soft-start-us = <800>;
+};
+
&vreg_l18a_2p85 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index 798f2d8a8237..e2cccc8314be 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -202,6 +202,31 @@ &blsp2_uart1 {
status = "okay";
};
+&ibb {
+ regulator-min-microamp = <800000>;
+ regulator-max-microamp = <800000>;
+ regulator-enable-ramp-delay = <200>;
+ regulator-over-current-protection;
+ regulator-pull-down;
+ regulator-ramp-delay = <1>;
+ regulator-settling-time-up-us = <600>;
+ regulator-settling-time-down-us = <1000>;
+ regulator-soft-start;
+ qcom,discharge-resistor-kohms = <300>;
+};
+
+&lab {
+ regulator-min-microamp = <200000>;
+ regulator-max-microamp = <200000>;
+ regulator-enable-ramp-delay = <500>;
+ regulator-over-current-protection;
+ regulator-pull-down;
+ regulator-ramp-delay = <1>;
+ regulator-settling-time-up-us = <50000>;
+ regulator-settling-time-down-us = <3000>;
+ regulator-soft-start;
+};
+
&mmcc {
status = "ok";
};
--
2.32.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 6/7] arm64: dts: qcom: msm8998-xperia: Add camera regulators
2021-09-09 12:37 [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform AngeloGioacchino Del Regno
` (3 preceding siblings ...)
2021-09-09 12:37 ` [PATCH v2 5/7] arm64: dts: qcom: msm8998-xperia: Configure display boost regulators AngeloGioacchino Del Regno
@ 2021-09-09 12:37 ` AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 7/7] arm64: dts: qcom: msm8998-xperia: Add audio clock and its pin AngeloGioacchino Del Regno
2021-09-24 23:26 ` [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform Bjorn Andersson
6 siblings, 0 replies; 8+ messages in thread
From: AngeloGioacchino Del Regno @ 2021-09-09 12:37 UTC (permalink / raw)
To: bjorn.andersson
Cc: agross, robh+dt, linux-arm-msm, devicetree, linux-kernel,
konrad.dybcio, marijn.suijten, martin.botka,
~postmarketos/upstreaming, phone-devel, paul.bouchara,
AngeloGioacchino Del Regno
All of the machines of the Sony Yoshino platform are equipped with
two cameras, sharing the same regulators configuration.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
---
.../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 56 +++++++++++++++++++
1 file changed, 56 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index e2cccc8314be..2c609e2cfc4a 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -30,6 +30,38 @@ board_vbat: vbat-regulator {
regulator-boot-on;
};
+ cam0_vdig_vreg: cam0-vdig {
+ compatible = "regulator-fixed";
+ regulator-name = "cam0_vdig";
+ startup-delay-us = <0>;
+ enable-active-high;
+ gpio = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cam0_vdig_default>;
+ };
+
+ cam1_vdig_vreg: cam1-vdig {
+ compatible = "regulator-fixed";
+ regulator-name = "cam1_vdig";
+ startup-delay-us = <0>;
+ enable-active-high;
+ gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cam1_vdig_default>;
+ vin-supply = <&vreg_s3a_1p35>;
+ };
+
+ cam_vio_vreg: cam-vio-vreg {
+ compatible = "regulator-fixed";
+ regulator-name = "cam_vio_vreg";
+ startup-delay-us = <0>;
+ enable-active-high;
+ gpio = <&pmi8998_gpio 1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cam_vio_default>;
+ vin-supply = <&vreg_lvs1a_1p8>;
+ };
+
touch_vddio_vreg: touch-vddio-vreg {
compatible = "regulator-fixed";
regulator-name = "touch_vddio_vreg";
@@ -278,6 +310,16 @@ cam_snapshot_pin_a: cam-snapshot-btn-active {
};
&pmi8998_gpio {
+ cam_vio_default: cam-vio-active {
+ pins = "gpio1";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ bias-disable;
+ drive-push-pull;
+ output-low;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
+ power-source = <1>;
+ };
+
vib_default: vib-en {
pins = "gpio5";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -540,6 +582,20 @@ cci1_default: cci1-default {
drive-strength = <2>;
};
+ cam0_vdig_default: cam0-vdig-default {
+ pins = "gpio21";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cam1_vdig_default: cam1-vdig-default {
+ pins = "gpio25";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
hall_sensor0_default: acc-cover-open {
pins = "gpio124";
function = "gpio";
--
2.32.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 7/7] arm64: dts: qcom: msm8998-xperia: Add audio clock and its pin
2021-09-09 12:37 [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform AngeloGioacchino Del Regno
` (4 preceding siblings ...)
2021-09-09 12:37 ` [PATCH v2 6/7] arm64: dts: qcom: msm8998-xperia: Add camera regulators AngeloGioacchino Del Regno
@ 2021-09-09 12:37 ` AngeloGioacchino Del Regno
2021-09-24 23:26 ` [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform Bjorn Andersson
6 siblings, 0 replies; 8+ messages in thread
From: AngeloGioacchino Del Regno @ 2021-09-09 12:37 UTC (permalink / raw)
To: bjorn.andersson
Cc: agross, robh+dt, linux-arm-msm, devicetree, linux-kernel,
konrad.dybcio, marijn.suijten, martin.botka,
~postmarketos/upstreaming, phone-devel, paul.bouchara,
AngeloGioacchino Del Regno
All smartphones of this platform are equipped with a WCD9335 audio
codec, getting its MCLK from PM8998 gpio13: add this clock to DT.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
---
.../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index 2c609e2cfc4a..91e391282181 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -20,6 +20,19 @@ / {
qcom,msm-id = <0x124 0x20000>, <0x124 0x20001>; /* 8998v2, v2.1 */
qcom,board-id = <8 0>;
+ clocks {
+ compatible = "simple-bus";
+
+ div1_mclk: divclk1 {
+ compatible = "gpio-gate-clock";
+ pinctrl-0 = <&audio_mclk_pin>;
+ pinctrl-names = "default";
+ clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
+ #clock-cells = <0>;
+ enable-gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
board_vbat: vbat-regulator {
compatible = "regulator-fixed";
regulator-name = "VBAT";
@@ -307,6 +320,12 @@ cam_snapshot_pin_a: cam-snapshot-btn-active {
input-enable;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
+
+ audio_mclk_pin: audio-mclk-pin-active {
+ pins = "gpio13";
+ function = "func2";
+ power-source = <0>;
+ };
};
&pmi8998_gpio {
--
2.32.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform
2021-09-09 12:37 [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform AngeloGioacchino Del Regno
` (5 preceding siblings ...)
2021-09-09 12:37 ` [PATCH v2 7/7] arm64: dts: qcom: msm8998-xperia: Add audio clock and its pin AngeloGioacchino Del Regno
@ 2021-09-24 23:26 ` Bjorn Andersson
6 siblings, 0 replies; 8+ messages in thread
From: Bjorn Andersson @ 2021-09-24 23:26 UTC (permalink / raw)
To: AngeloGioacchino Del Regno
Cc: linux-kernel, konrad.dybcio, robh+dt, phone-devel,
marijn.suijten, paul.bouchara, devicetree, agross, linux-arm-msm,
martin.botka, ~postmarketos/upstreaming
On Thu, 9 Sep 2021 14:37:27 +0200, AngeloGioacchino Del Regno wrote:
> This commit introduces support for the Sony Yoshino platform, using
> the MSM8998 SoC, including:
> - Sony Xperia XZ1 (codename Poplar),
> - Sony Xperia XZ1 Compact (codename Lilac),
> - Sony Xperia XZ Premium (codename Maple).
>
> All of the three aforementioned smartphones are sharing a 99%
> equal board configuration, with very small differences between
> each other, which is the reason for the introduction of a common
> msm8998-sony-xperia-yoshino DT.
>
> [...]
Applied, thanks!
[1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform
commit: 390883af89d2ed653c3f7eefc06368241d422a38
[2/7] arm64: dts: qcom: msm8998-xperia: Add RMI4 touchscreen support
commit: ebe0932e4fe5a5a0eb197f1de50442a2bf2d7b08
[3/7] arm64: dts: qcom: msm8998-xperia: Add support for wcn3990 Bluetooth
commit: 58ba4efabc150f85ba3c80a31c37e03adebd5135
[4/7] arm64: dts: qcom: msm8998-xperia: Add support for gpio vibrator
commit: 4de9700d0332f21d12ffec7ba67733ea9a6581a5
[5/7] arm64: dts: qcom: msm8998-xperia: Configure display boost regulators
commit: 67372ee2c0bca8bfb1e16e961e9f3969d434f978
[6/7] arm64: dts: qcom: msm8998-xperia: Add camera regulators
commit: a5fde059398b5d985a3fcfea06f75cce2a88081f
[7/7] arm64: dts: qcom: msm8998-xperia: Add audio clock and its pin
commit: 6cadaa14f290a0b7c2f3b2b7afd3192c5b49473f
Best regards,
--
Bjorn Andersson <bjorn.andersson@linaro.org>
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2021-09-24 23:26 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-09-09 12:37 [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 2/7] arm64: dts: qcom: msm8998-xperia: Add RMI4 touchscreen support AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 3/7] arm64: dts: qcom: msm8998-xperia: Add support for wcn3990 Bluetooth AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 4/7] arm64: dts: qcom: msm8998-xperia: Add support for gpio vibrator AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 5/7] arm64: dts: qcom: msm8998-xperia: Configure display boost regulators AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 6/7] arm64: dts: qcom: msm8998-xperia: Add camera regulators AngeloGioacchino Del Regno
2021-09-09 12:37 ` [PATCH v2 7/7] arm64: dts: qcom: msm8998-xperia: Add audio clock and its pin AngeloGioacchino Del Regno
2021-09-24 23:26 ` [PATCH v2 1/7] arm64: dts: qcom: Introduce support for MSM8998 Sony Yoshino platform Bjorn Andersson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).