All of lore.kernel.org
 help / color / mirror / Atom feed
From: Amjad Ouled-Ameur <aouledameur@baylibre.com>
To: balbi@kernel.org
Cc: Amjad Ouled-Ameur <aouledameur@baylibre.com>,
	p.zabel@pengutronix.de, khilman@baylibre.com,
	jbrunet@baylibre.com, linux-amlogic@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-usb@vger.kernel.org
Subject: [PATCH v3 2/3] usb: dwc3: meson-g12a: fix shared reset control use
Date: Fri, 12 Nov 2021 17:28:26 +0100	[thread overview]
Message-ID: <20211112162827.128319-3-aouledameur@baylibre.com> (raw)
In-Reply-To: <20211112162827.128319-1-aouledameur@baylibre.com>


reset_control_(de)assert() calls are called on a shared reset line when
reset_control_reset has been used. This is not allowed by the reset
framework.

Use reset_control_rearm() call in suspend() and remove() as a way to state
that the resource is no longer used, hence the shared reset line
may be triggered again by other devices. Use reset_control_rearm() also in
case probe fails after reset() has been called.

reset_control_rearm() keeps use of triggered_count sane in the reset
framework, use of reset_control_reset() on shared reset line should be
balanced with reset_control_rearm().

Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
---
 drivers/usb/dwc3/dwc3-meson-g12a.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c b/drivers/usb/dwc3/dwc3-meson-g12a.c
index d0f9b7c296b0..bd814df3bf8b 100644
--- a/drivers/usb/dwc3/dwc3-meson-g12a.c
+++ b/drivers/usb/dwc3/dwc3-meson-g12a.c
@@ -755,16 +755,16 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
 
 	ret = dwc3_meson_g12a_get_phys(priv);
 	if (ret)
-		goto err_disable_clks;
+		goto err_rearm;
 
 	ret = priv->drvdata->setup_regmaps(priv, base);
 	if (ret)
-		goto err_disable_clks;
+		goto err_rearm;
 
 	if (priv->vbus) {
 		ret = regulator_enable(priv->vbus);
 		if (ret)
-			goto err_disable_clks;
+			goto err_rearm;
 	}
 
 	/* Get dr_mode */
@@ -825,6 +825,9 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
 	if (priv->vbus)
 		regulator_disable(priv->vbus);
 
+err_rearm:
+	reset_control_rearm(priv->reset);
+
 err_disable_clks:
 	clk_bulk_disable_unprepare(priv->drvdata->num_clks,
 				   priv->drvdata->clks);
@@ -852,6 +855,8 @@ static int dwc3_meson_g12a_remove(struct platform_device *pdev)
 	pm_runtime_put_noidle(dev);
 	pm_runtime_set_suspended(dev);
 
+	reset_control_rearm(priv->reset);
+
 	clk_bulk_disable_unprepare(priv->drvdata->num_clks,
 				   priv->drvdata->clks);
 
@@ -892,7 +897,7 @@ static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
 		phy_exit(priv->phys[i]);
 	}
 
-	reset_control_assert(priv->reset);
+	reset_control_rearm(priv->reset);
 
 	return 0;
 }
@@ -902,7 +907,9 @@ static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
 	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
 	int i, ret;
 
-	reset_control_deassert(priv->reset);
+	ret = reset_control_reset(priv->reset);
+	if (ret)
+		return ret;
 
 	ret = priv->drvdata->usb_init(priv);
 	if (ret)
-- 
2.25.1


WARNING: multiple messages have this Message-ID (diff)
From: Amjad Ouled-Ameur <aouledameur@baylibre.com>
To: balbi@kernel.org
Cc: Amjad Ouled-Ameur <aouledameur@baylibre.com>,
	p.zabel@pengutronix.de, khilman@baylibre.com,
	jbrunet@baylibre.com, linux-amlogic@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-usb@vger.kernel.org
Subject: [PATCH v3 2/3] usb: dwc3: meson-g12a: fix shared reset control use
Date: Fri, 12 Nov 2021 17:28:26 +0100	[thread overview]
Message-ID: <20211112162827.128319-3-aouledameur@baylibre.com> (raw)
In-Reply-To: <20211112162827.128319-1-aouledameur@baylibre.com>


reset_control_(de)assert() calls are called on a shared reset line when
reset_control_reset has been used. This is not allowed by the reset
framework.

Use reset_control_rearm() call in suspend() and remove() as a way to state
that the resource is no longer used, hence the shared reset line
may be triggered again by other devices. Use reset_control_rearm() also in
case probe fails after reset() has been called.

reset_control_rearm() keeps use of triggered_count sane in the reset
framework, use of reset_control_reset() on shared reset line should be
balanced with reset_control_rearm().

Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
---
 drivers/usb/dwc3/dwc3-meson-g12a.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c b/drivers/usb/dwc3/dwc3-meson-g12a.c
index d0f9b7c296b0..bd814df3bf8b 100644
--- a/drivers/usb/dwc3/dwc3-meson-g12a.c
+++ b/drivers/usb/dwc3/dwc3-meson-g12a.c
@@ -755,16 +755,16 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
 
 	ret = dwc3_meson_g12a_get_phys(priv);
 	if (ret)
-		goto err_disable_clks;
+		goto err_rearm;
 
 	ret = priv->drvdata->setup_regmaps(priv, base);
 	if (ret)
-		goto err_disable_clks;
+		goto err_rearm;
 
 	if (priv->vbus) {
 		ret = regulator_enable(priv->vbus);
 		if (ret)
-			goto err_disable_clks;
+			goto err_rearm;
 	}
 
 	/* Get dr_mode */
@@ -825,6 +825,9 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
 	if (priv->vbus)
 		regulator_disable(priv->vbus);
 
+err_rearm:
+	reset_control_rearm(priv->reset);
+
 err_disable_clks:
 	clk_bulk_disable_unprepare(priv->drvdata->num_clks,
 				   priv->drvdata->clks);
@@ -852,6 +855,8 @@ static int dwc3_meson_g12a_remove(struct platform_device *pdev)
 	pm_runtime_put_noidle(dev);
 	pm_runtime_set_suspended(dev);
 
+	reset_control_rearm(priv->reset);
+
 	clk_bulk_disable_unprepare(priv->drvdata->num_clks,
 				   priv->drvdata->clks);
 
@@ -892,7 +897,7 @@ static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
 		phy_exit(priv->phys[i]);
 	}
 
-	reset_control_assert(priv->reset);
+	reset_control_rearm(priv->reset);
 
 	return 0;
 }
@@ -902,7 +907,9 @@ static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
 	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
 	int i, ret;
 
-	reset_control_deassert(priv->reset);
+	ret = reset_control_reset(priv->reset);
+	if (ret)
+		return ret;
 
 	ret = priv->drvdata->usb_init(priv);
 	if (ret)
-- 
2.25.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

  parent reply	other threads:[~2021-11-12 16:32 UTC|newest]

Thread overview: 24+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-11-12 16:28 [PATCH v3 0/3] usb: meson: fix shared reset control use Amjad Ouled-Ameur
2021-11-12 16:28 ` Amjad Ouled-Ameur
2021-11-12 16:28 ` [PATCH v3 1/3] phy: amlogic: phy-meson-gxl-usb2: fix shared reset controller use Amjad Ouled-Ameur
2021-11-12 16:28   ` Amjad Ouled-Ameur
2021-11-20 23:39   ` Martin Blumenstingl
2021-11-20 23:39     ` Martin Blumenstingl
2021-11-22  9:03   ` Philipp Zabel
2021-11-22  9:03     ` Philipp Zabel
2021-12-05 21:13     ` Amjad Ouled-Ameur
2021-12-05 21:13       ` Amjad Ouled-Ameur
2021-11-12 16:28 ` Amjad Ouled-Ameur [this message]
2021-11-12 16:28   ` [PATCH v3 2/3] usb: dwc3: meson-g12a: fix shared reset control use Amjad Ouled-Ameur
2021-11-20 23:51   ` Martin Blumenstingl
2021-11-20 23:51     ` Martin Blumenstingl
2021-11-22  9:04     ` Anand Moon
2021-11-22  9:04       ` Anand Moon
2021-11-12 16:28 ` [PATCH v3 3/3] phy: amlogic: meson8b-usb2: " Amjad Ouled-Ameur
2021-11-12 16:28   ` Amjad Ouled-Ameur
2021-11-20 23:57   ` Martin Blumenstingl
2021-11-20 23:57     ` Martin Blumenstingl
2021-12-05 21:35     ` Amjad Ouled-Ameur
2021-12-05 21:35       ` Amjad Ouled-Ameur
2021-11-19 19:27 ` [PATCH v3 0/3] usb: meson: " Kevin Hilman
2021-11-19 19:27   ` Kevin Hilman

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20211112162827.128319-3-aouledameur@baylibre.com \
    --to=aouledameur@baylibre.com \
    --cc=balbi@kernel.org \
    --cc=jbrunet@baylibre.com \
    --cc=khilman@baylibre.com \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=p.zabel@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.