From: "Kumar, Anil" <anilkumar.v@ti.com>
To: Tushar Behera <tushar.behera@linaro.org>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>,
"linux-samsung-soc@vger.kernel.org"
<linux-samsung-soc@vger.kernel.org>,
"devicetree-discuss@lists.ozlabs.org"
<devicetree-discuss@lists.ozlabs.org>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>,
"kgene.kim@samsung.com" <kgene.kim@samsung.com>,
"patches@linaro.org" <patches@linaro.org>
Subject: RE: [PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry
Date: Thu, 7 Feb 2013 05:49:39 +0000 [thread overview]
Message-ID: <F3DBB1B3EF102E4994C89758CFCA32412C4DE1@DBDE01.ent.ti.com> (raw)
In-Reply-To: <1360214129-4096-2-git-send-email-tushar.behera@linaro.org>
On Thu, Feb 07, 2013 at 10:45:26, Tushar Behera wrote:
> From: Amit Daniel Kachhap <amit.daniel@samsung.com>
>
> Added S5M8767 PMIC DT nodes to Arndale board.
>
> Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
> ---
> arch/arm/boot/dts/exynos5250-arndale.dts | 213 +++++++++++++++++++++++++++++-
> 1 files changed, 212 insertions(+), 1 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
> index 9ce40df..b40a02f 100644
> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
> @@ -25,7 +25,218 @@
> };
>
> i2c@12C60000 {
> - status = "disabled";
> + status = "okay";
Is there any need to change status "okay" here as in dtsi file it is
by default okay ?
> + samsung,i2c-sda-delay = <100>;
> + samsung,i2c-max-bus-freq = <20000>;
> + samsung,i2c-slave-addr = <0x66>;
> + gpios = <&gpb3 0 2 3 0>,
> + <&gpb3 1 2 3 0>;
> +
> + s5m8767_pmic@66 {
> + compatible = "samsung,s5m8767-pmic";
> + reg = <0x66>;
> +
> + s5m8767,pmic-buck2-dvs-voltage = <1300000>;
> + s5m8767,pmic-buck3-dvs-voltage = <1100000>;
> + s5m8767,pmic-buck4-dvs-voltage = <1200000>;
> + s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1 0 0>,
> + <&gpd1 1 1 0 0>,
> + <&gpd1 2 1 0 0>;
> + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>,
> + <&gpx2 4 1 0 0>,
> + <&gpx2 5 1 0 0>;
> + regulators {
> + ldo1_reg: LDO1 {
> + regulator-name = "VDD_ALIVE_1.0V";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + regulator-boot-on;
> + op_mode = <1>;
> + };
> +
> + ldo2_reg: LDO2 {
> + regulator-name = "VDD_28IO_DP_1.35V";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo3_reg: LDO3 {
> + regulator-name = "VDD_COMMON1_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo4_reg: LDO4 {
> + regulator-name = "VDD_IOPERI_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo5_reg: LDO5 {
> + regulator-name = "VDD_EXT_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo6_reg: LDO6 {
> + regulator-name = "VDD_MPLL_1.1V";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo7_reg: LDO7 {
> + regulator-name = "VDD_XPLL_1.1V";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo8_reg: LDO8 {
> + regulator-name = "VDD_COMMON2_1.0V";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo9_reg: LDO9 {
> + regulator-name = "VDD_33ON_3.0V";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo10_reg: LDO10 {
> + regulator-name = "VDD_COMMON3_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo11_reg: LDO11 {
> + regulator-name = "VDD_ABB2_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo12_reg: LDO12 {
> + regulator-name = "VDD_USB_3.0V";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo13_reg: LDO13 {
> + regulator-name = "VDDQ_C2C_W_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo14_reg: LDO14 {
> + regulator-name = "VDD18_ABB0_3_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo15_reg: LDO15 {
> + regulator-name = "VDD10_COMMON4_1.0V";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo16_reg: LDO16 {
> + regulator-name = "VDD18_HSIC_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo17_reg: LDO17 {
> + regulator-name = "VDDQ_MMC2_3_2.8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo18_reg: LDO18 {
> + regulator-name = "VDD_33ON_2.8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + buck1_reg: BUCK1 {
> + regulator-name = "VDD_MIF_1.2V";
> + regulator-min-microvolt = <950000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + regulator-boot-on;
> + op_mode = <1>;
> + };
> +
> + buck2_reg: BUCK2 {
> + regulator-name = "vdd_arm";
> + regulator-min-microvolt = <925000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + op_mode = <1>;
> + };
> +
> + buck3_reg: BUCK3 {
> + regulator-name = "VDD_INT_1.0V";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + regulator-boot-on;
> + op_mode = <1>;
> + };
> +
> + buck4_reg: BUCK4 {
> + regulator-name = "VDD_G3D_1.0V";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + buck5_reg: BUCK5 {
> + regulator-name = "VDD_MEM_1.35V";
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1355000>;
> + regulator-always-on;
> + regulator-boot-on;
> + op_mode = <1>;
> + };
> +
> + };
> + };
> };
>
> i2c@12C70000 {
> --
> 1.7.4.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
WARNING: multiple messages have this Message-ID (diff)
From: anilkumar.v@ti.com (Kumar, Anil)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry
Date: Thu, 7 Feb 2013 05:49:39 +0000 [thread overview]
Message-ID: <F3DBB1B3EF102E4994C89758CFCA32412C4DE1@DBDE01.ent.ti.com> (raw)
In-Reply-To: <1360214129-4096-2-git-send-email-tushar.behera@linaro.org>
On Thu, Feb 07, 2013 at 10:45:26, Tushar Behera wrote:
> From: Amit Daniel Kachhap <amit.daniel@samsung.com>
>
> Added S5M8767 PMIC DT nodes to Arndale board.
>
> Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
> ---
> arch/arm/boot/dts/exynos5250-arndale.dts | 213 +++++++++++++++++++++++++++++-
> 1 files changed, 212 insertions(+), 1 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
> index 9ce40df..b40a02f 100644
> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
> @@ -25,7 +25,218 @@
> };
>
> i2c at 12C60000 {
> - status = "disabled";
> + status = "okay";
Is there any need to change status "okay" here as in dtsi file it is
by default okay ?
> + samsung,i2c-sda-delay = <100>;
> + samsung,i2c-max-bus-freq = <20000>;
> + samsung,i2c-slave-addr = <0x66>;
> + gpios = <&gpb3 0 2 3 0>,
> + <&gpb3 1 2 3 0>;
> +
> + s5m8767_pmic at 66 {
> + compatible = "samsung,s5m8767-pmic";
> + reg = <0x66>;
> +
> + s5m8767,pmic-buck2-dvs-voltage = <1300000>;
> + s5m8767,pmic-buck3-dvs-voltage = <1100000>;
> + s5m8767,pmic-buck4-dvs-voltage = <1200000>;
> + s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1 0 0>,
> + <&gpd1 1 1 0 0>,
> + <&gpd1 2 1 0 0>;
> + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>,
> + <&gpx2 4 1 0 0>,
> + <&gpx2 5 1 0 0>;
> + regulators {
> + ldo1_reg: LDO1 {
> + regulator-name = "VDD_ALIVE_1.0V";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + regulator-boot-on;
> + op_mode = <1>;
> + };
> +
> + ldo2_reg: LDO2 {
> + regulator-name = "VDD_28IO_DP_1.35V";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo3_reg: LDO3 {
> + regulator-name = "VDD_COMMON1_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo4_reg: LDO4 {
> + regulator-name = "VDD_IOPERI_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo5_reg: LDO5 {
> + regulator-name = "VDD_EXT_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo6_reg: LDO6 {
> + regulator-name = "VDD_MPLL_1.1V";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo7_reg: LDO7 {
> + regulator-name = "VDD_XPLL_1.1V";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo8_reg: LDO8 {
> + regulator-name = "VDD_COMMON2_1.0V";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo9_reg: LDO9 {
> + regulator-name = "VDD_33ON_3.0V";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo10_reg: LDO10 {
> + regulator-name = "VDD_COMMON3_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo11_reg: LDO11 {
> + regulator-name = "VDD_ABB2_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo12_reg: LDO12 {
> + regulator-name = "VDD_USB_3.0V";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo13_reg: LDO13 {
> + regulator-name = "VDDQ_C2C_W_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo14_reg: LDO14 {
> + regulator-name = "VDD18_ABB0_3_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo15_reg: LDO15 {
> + regulator-name = "VDD10_COMMON4_1.0V";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo16_reg: LDO16 {
> + regulator-name = "VDD18_HSIC_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo17_reg: LDO17 {
> + regulator-name = "VDDQ_MMC2_3_2.8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + ldo18_reg: LDO18 {
> + regulator-name = "VDD_33ON_2.8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + buck1_reg: BUCK1 {
> + regulator-name = "VDD_MIF_1.2V";
> + regulator-min-microvolt = <950000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + regulator-boot-on;
> + op_mode = <1>;
> + };
> +
> + buck2_reg: BUCK2 {
> + regulator-name = "vdd_arm";
> + regulator-min-microvolt = <925000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + op_mode = <1>;
> + };
> +
> + buck3_reg: BUCK3 {
> + regulator-name = "VDD_INT_1.0V";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + regulator-boot-on;
> + op_mode = <1>;
> + };
> +
> + buck4_reg: BUCK4 {
> + regulator-name = "VDD_G3D_1.0V";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + op_mode = <1>;
> + };
> +
> + buck5_reg: BUCK5 {
> + regulator-name = "VDD_MEM_1.35V";
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1355000>;
> + regulator-always-on;
> + regulator-boot-on;
> + op_mode = <1>;
> + };
> +
> + };
> + };
> };
>
> i2c at 12C70000 {
> --
> 1.7.4.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
next prev parent reply other threads:[~2013-02-07 5:49 UTC|newest]
Thread overview: 38+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-02-07 5:15 [PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons Tushar Behera
2013-02-07 5:15 ` Tushar Behera
2013-02-07 5:15 ` [PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry Tushar Behera
2013-02-07 5:15 ` Tushar Behera
2013-02-07 5:49 ` Kumar, Anil [this message]
2013-02-07 5:49 ` Kumar, Anil
2013-02-07 5:56 ` Tushar Behera
2013-02-07 5:56 ` Tushar Behera
2013-02-11 0:38 ` amit daniel kachhap
2013-02-11 0:38 ` amit daniel kachhap
2013-03-11 2:05 ` Kukjin Kim
2013-03-11 2:05 ` Kukjin Kim
2013-02-07 5:15 ` [PATCH 3/5] ARM: dts: exynos5250-arndale: Add vmmc regulator support Tushar Behera
2013-02-07 5:15 ` Tushar Behera
2013-02-07 5:15 ` [PATCH 4/5] ARM: dts: exynos5250-arndale: Add MFC codec support Tushar Behera
2013-02-07 5:15 ` Tushar Behera
2013-02-07 5:15 ` [PATCH 5/5] ARM: dts: exynos5250-arndale: Add HDMI HPD and regulator node Tushar Behera
2013-02-07 5:15 ` Tushar Behera
2013-02-07 6:17 ` [PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons Kumar, Anil
2013-02-07 6:17 ` Kumar, Anil
2013-02-07 6:26 ` Tushar Behera
2013-02-07 6:26 ` Tushar Behera
2013-02-07 6:36 ` Manish Badarkhe
2013-02-07 6:36 ` Manish Badarkhe
2013-02-07 6:56 ` Tushar Behera
2013-02-07 6:56 ` Tushar Behera
2013-02-07 7:43 ` Girish KS
2013-02-07 7:43 ` Girish KS
2013-02-07 9:40 ` Tushar Behera
2013-02-07 9:40 ` Tushar Behera
2013-02-07 11:25 ` Tomasz Figa
2013-02-07 11:25 ` Tomasz Figa
2013-02-07 10:30 ` Tomasz Figa
2013-02-07 10:30 ` Tomasz Figa
2013-03-11 2:05 ` Kukjin Kim
2013-03-11 2:05 ` Kukjin Kim
2013-03-11 9:44 ` Tushar Behera
2013-03-11 9:44 ` Tushar Behera
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=F3DBB1B3EF102E4994C89758CFCA32412C4DE1@DBDE01.ent.ti.com \
--to=anilkumar.v@ti.com \
--cc=amit.daniel@samsung.com \
--cc=devicetree-discuss@lists.ozlabs.org \
--cc=kgene.kim@samsung.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=patches@linaro.org \
--cc=tushar.behera@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.