From: Miquel Raynal <miquel.raynal@bootlin.com> To: Mark Brown <broonie@kernel.org>, Michal Simek <michal.simek@xilinx.com>, Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com>, Tudor Ambarus <Tudor.Ambarus@microchip.com>, linux-arm-kernel@lists.infradead.org, Thomas Petazzoni <thomas.petazzoni@bootlin.com>, linux-spi@vger.kernel.org Subject: [PATCH v2 2/7] spi: zynq-qspi: Keep the naming consistent across the driver Date: Fri, 8 Nov 2019 15:07:39 +0100 [thread overview] Message-ID: <20191108140744.1734-3-miquel.raynal@bootlin.com> (raw) In-Reply-To: <20191108140744.1734-1-miquel.raynal@bootlin.com> In this driver (and also in a lot of other drivers in drivers/spi/), the spi_controller structure is sometimes referred as 'ctlr' and sometimes as 'ctrl'. Grepping there shows that 'ctlr' seems to be more common so keep the naming consistent in this driver and s/ctrl/ctlr/. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> --- drivers/spi/spi-zynq-qspi.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/drivers/spi/spi-zynq-qspi.c b/drivers/spi/spi-zynq-qspi.c index 713f9a03a40a..641691f5dedf 100644 --- a/drivers/spi/spi-zynq-qspi.c +++ b/drivers/spi/spi-zynq-qspi.c @@ -284,8 +284,8 @@ static void zynq_qspi_txfifo_op(struct zynq_qspi *xqspi, unsigned int size) */ static void zynq_qspi_chipselect(struct spi_device *spi, bool assert) { - struct spi_controller *ctrl = spi->master; - struct zynq_qspi *xqspi = spi_controller_get_devdata(ctrl); + struct spi_controller *ctlr = spi->master; + struct zynq_qspi *xqspi = spi_controller_get_devdata(ctlr); u32 config_reg; config_reg = zynq_qspi_read(xqspi, ZYNQ_QSPI_CONFIG_OFFSET); @@ -365,10 +365,10 @@ static int zynq_qspi_config_op(struct zynq_qspi *xqspi, struct spi_device *spi) */ static int zynq_qspi_setup_op(struct spi_device *spi) { - struct spi_controller *ctrl = spi->master; - struct zynq_qspi *qspi = spi_controller_get_devdata(ctrl); + struct spi_controller *ctlr = spi->master; + struct zynq_qspi *qspi = spi_controller_get_devdata(ctlr); - if (ctrl->busy) + if (ctlr->busy) return -EBUSY; clk_enable(qspi->refclk); -- 2.20.1
WARNING: multiple messages have this Message-ID (diff)
From: Miquel Raynal <miquel.raynal@bootlin.com> To: Mark Brown <broonie@kernel.org>, Michal Simek <michal.simek@xilinx.com>, Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com>, Tudor Ambarus <Tudor.Ambarus@microchip.com>, linux-arm-kernel@lists.infradead.org, Thomas Petazzoni <thomas.petazzoni@bootlin.com>, linux-spi@vger.kernel.org Subject: [PATCH v2 2/7] spi: zynq-qspi: Keep the naming consistent across the driver Date: Fri, 8 Nov 2019 15:07:39 +0100 [thread overview] Message-ID: <20191108140744.1734-3-miquel.raynal@bootlin.com> (raw) In-Reply-To: <20191108140744.1734-1-miquel.raynal@bootlin.com> In this driver (and also in a lot of other drivers in drivers/spi/), the spi_controller structure is sometimes referred as 'ctlr' and sometimes as 'ctrl'. Grepping there shows that 'ctlr' seems to be more common so keep the naming consistent in this driver and s/ctrl/ctlr/. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> --- drivers/spi/spi-zynq-qspi.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/drivers/spi/spi-zynq-qspi.c b/drivers/spi/spi-zynq-qspi.c index 713f9a03a40a..641691f5dedf 100644 --- a/drivers/spi/spi-zynq-qspi.c +++ b/drivers/spi/spi-zynq-qspi.c @@ -284,8 +284,8 @@ static void zynq_qspi_txfifo_op(struct zynq_qspi *xqspi, unsigned int size) */ static void zynq_qspi_chipselect(struct spi_device *spi, bool assert) { - struct spi_controller *ctrl = spi->master; - struct zynq_qspi *xqspi = spi_controller_get_devdata(ctrl); + struct spi_controller *ctlr = spi->master; + struct zynq_qspi *xqspi = spi_controller_get_devdata(ctlr); u32 config_reg; config_reg = zynq_qspi_read(xqspi, ZYNQ_QSPI_CONFIG_OFFSET); @@ -365,10 +365,10 @@ static int zynq_qspi_config_op(struct zynq_qspi *xqspi, struct spi_device *spi) */ static int zynq_qspi_setup_op(struct spi_device *spi) { - struct spi_controller *ctrl = spi->master; - struct zynq_qspi *qspi = spi_controller_get_devdata(ctrl); + struct spi_controller *ctlr = spi->master; + struct zynq_qspi *qspi = spi_controller_get_devdata(ctlr); - if (ctrl->busy) + if (ctlr->busy) return -EBUSY; clk_enable(qspi->refclk); -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-11-08 14:07 UTC|newest] Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-11-08 14:07 [PATCH v2 0/7] spi: zynq-qspi: Clarify and fix the chip selection Miquel Raynal 2019-11-08 14:07 ` [PATCH v2 1/7] spi: zynq-qspi: Anything else than CS0 is not supported yet Miquel Raynal 2019-11-08 14:07 ` Miquel Raynal 2019-11-08 17:45 ` Applied "spi: zynq-qspi: Anything else than CS0 is not supported yet" to the spi tree Mark Brown 2019-11-08 17:45 ` Mark Brown 2019-11-08 14:07 ` Miquel Raynal [this message] 2019-11-08 14:07 ` [PATCH v2 2/7] spi: zynq-qspi: Keep the naming consistent across the driver Miquel Raynal 2019-11-08 14:07 ` [PATCH v2 3/7] spi: zynq-qspi: Keep the bitfields naming consistent Miquel Raynal 2019-11-08 14:07 ` Miquel Raynal 2019-11-08 17:45 ` Applied "spi: zynq-qspi: Keep the bitfields naming consistent" to the spi tree Mark Brown 2019-11-08 17:45 ` Mark Brown 2019-11-08 14:07 ` [PATCH v2 4/7] spi: zynq-qspi: Enhance the Linear CFG bit definitions Miquel Raynal 2019-11-08 14:07 ` Miquel Raynal 2019-11-08 17:45 ` Applied "spi: zynq-qspi: Enhance the Linear CFG bit definitions" to the spi tree Mark Brown 2019-11-08 17:45 ` Mark Brown 2019-11-08 14:07 ` [PATCH v2 5/7] spi: zynq-qspi: Clarify the select chip function Miquel Raynal 2019-11-08 14:07 ` Miquel Raynal 2019-11-08 17:45 ` Applied "spi: zynq-qspi: Clarify the select chip function" to the spi tree Mark Brown 2019-11-08 17:45 ` Mark Brown 2019-11-08 14:07 ` [PATCH v2 6/7] spi: zynq-qspi: Do the actual hardware initialization later in the probe Miquel Raynal 2019-11-08 14:07 ` Miquel Raynal 2019-11-08 17:45 ` Applied "spi: zynq-qspi: Do the actual hardware initialization later in the probe" to the spi tree Mark Brown 2019-11-08 17:45 ` Mark Brown 2019-11-08 14:07 ` [PATCH v2 7/7] spi: zynq-qspi: Support two chip selects Miquel Raynal 2019-11-08 14:07 ` Miquel Raynal 2019-11-08 17:45 ` Applied "spi: zynq-qspi: Support two chip selects" to the spi tree Mark Brown 2019-11-08 17:45 ` Mark Brown
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20191108140744.1734-3-miquel.raynal@bootlin.com \ --to=miquel.raynal@bootlin.com \ --cc=Tudor.Ambarus@microchip.com \ --cc=broonie@kernel.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-spi@vger.kernel.org \ --cc=michal.simek@xilinx.com \ --cc=naga.sureshkumar.relli@xilinx.com \ --cc=thomas.petazzoni@bootlin.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.