[U-Boot] [PATCH v3 03/11] arm: rpi: Bring in kernel device tree files

[Simon Glass <sjg@chromium.org>]

Bring in the device tree files from Linux v4.1.

Signed-off-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2: None

 arch/arm/dts/Makefile                 |   2 +
 arch/arm/dts/bcm2835-rpi-b.dts        |  23 ++++
 arch/arm/dts/bcm2835-rpi.dtsi         |  51 +++++++++
 arch/arm/dts/bcm2835.dtsi             | 192 ++++++++++++++++++++++++++++++++++
 include/dt-bindings/pinctrl/bcm2835.h |  27 +++++
 5 files changed, 295 insertions(+)
 create mode 100644 arch/arm/dts/bcm2835-rpi-b.dts
 create mode 100644 arch/arm/dts/bcm2835-rpi.dtsi
 create mode 100644 arch/arm/dts/bcm2835.dtsi
 create mode 100644 include/dt-bindings/pinctrl/bcm2835.h

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 2df957c..949048c 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -52,6 +52,8 @@ dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
 	zynq-zc770-xm013.dtb
 dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb
 
+dtb-$(CONFIG_ARCH_BCM283X) += bcm2835-rpi-b.dtb
+
 dtb-$(CONFIG_ARCH_SOCFPGA) +=				\
 	socfpga_arria5_socdk.dtb			\
 	socfpga_cyclone5_socdk.dtb			\
diff --git a/arch/arm/dts/bcm2835-rpi-b.dts b/arch/arm/dts/bcm2835-rpi-b.dts
new file mode 100644
index 0000000..ee89b79
--- /dev/null
+++ b/arch/arm/dts/bcm2835-rpi-b.dts
@@ -0,0 +1,23 @@
+/dts-v1/;
+#include "bcm2835-rpi.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b", "brcm,bcm2835";
+	model = "Raspberry Pi Model B";
+
+	leds {
+		act {
+			gpios = <&gpio 16 1>;
+		};
+	};
+};
+
+&gpio {
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
+
+	/* I2S interface */
+	i2s_alt2: i2s_alt2 {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <BCM2835_FSEL_ALT2>;
+	};
+};
diff --git a/arch/arm/dts/bcm2835-rpi.dtsi b/arch/arm/dts/bcm2835-rpi.dtsi
new file mode 100644
index 0000000..46780bb
--- /dev/null
+++ b/arch/arm/dts/bcm2835-rpi.dtsi
@@ -0,0 +1,51 @@
+#include "bcm2835.dtsi"
+
+/ {
+	memory {
+		reg = <0 0x10000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		act {
+			label = "ACT";
+			default-state = "keep";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&gpio {
+	pinctrl-names = "default";
+
+	gpioout: gpioout {
+		brcm,pins = <6>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	alt0: alt0 {
+		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 14 15 40 45>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+
+	alt3: alt3 {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&sdhci {
+	status = "okay";
+	bus-width = <4>;
+};
diff --git a/arch/arm/dts/bcm2835.dtsi b/arch/arm/dts/bcm2835.dtsi
new file mode 100644
index 0000000..301c73f
--- /dev/null
+++ b/arch/arm/dts/bcm2835.dtsi
@@ -0,0 +1,192 @@
+#include <dt-bindings/pinctrl/bcm2835.h>
+#include "skeleton.dtsi"
+
+/ {
+	compatible = "brcm,bcm2835";
+	model = "BCM2835";
+	interrupt-parent = <&intc>;
+
+	chosen {
+		bootargs = "earlyprintk console=ttyAMA0";
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x7e000000 0x20000000 0x02000000>;
+		dma-ranges = <0x40000000 0x00000000 0x20000000>;
+
+		timer at 7e003000 {
+			compatible = "brcm,bcm2835-system-timer";
+			reg = <0x7e003000 0x1000>;
+			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
+			clock-frequency = <1000000>;
+		};
+
+		dma: dma at 7e007000 {
+			compatible = "brcm,bcm2835-dma";
+			reg = <0x7e007000 0xf00>;
+			interrupts = <1 16>,
+				     <1 17>,
+				     <1 18>,
+				     <1 19>,
+				     <1 20>,
+				     <1 21>,
+				     <1 22>,
+				     <1 23>,
+				     <1 24>,
+				     <1 25>,
+				     <1 26>,
+				     <1 27>,
+				     <1 28>;
+
+			#dma-cells = <1>;
+			brcm,dma-channel-mask = <0x7f35>;
+		};
+
+		intc: interrupt-controller at 7e00b200 {
+			compatible = "brcm,bcm2835-armctrl-ic";
+			reg = <0x7e00b200 0x200>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		watchdog at 7e100000 {
+			compatible = "brcm,bcm2835-pm-wdt";
+			reg = <0x7e100000 0x28>;
+		};
+
+		rng at 7e104000 {
+			compatible = "brcm,bcm2835-rng";
+			reg = <0x7e104000 0x10>;
+		};
+
+		mailbox: mailbox at 7e00b800 {
+			compatible = "brcm,bcm2835-mbox";
+			reg = <0x7e00b880 0x40>;
+			interrupts = <0 1>;
+			#mbox-cells = <0>;
+		};
+
+		gpio: gpio at 7e200000 {
+			compatible = "brcm,bcm2835-gpio";
+			reg = <0x7e200000 0xb4>;
+			/*
+			 * The GPIO IP block is designed for 3 banks of GPIOs.
+			 * Each bank has a GPIO interrupt for itself.
+			 * There is an overall "any bank" interrupt.
+			 * In order, these are GIC interrupts 17, 18, 19, 20.
+			 * Since the BCM2835 only has 2 banks, the 2nd bank
+			 * interrupt output appears to be mirrored onto the
+			 * 3rd bank's interrupt signal.
+			 * So, a bank0 interrupt shows up on 17, 20, and
+			 * a bank1 interrupt shows up on 18, 19, 20!
+			 */
+			interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		uart at 7e201000 {
+			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
+			reg = <0x7e201000 0x1000>;
+			interrupts = <2 25>;
+			clock-frequency = <3000000>;
+			arm,primecell-periphid = <0x00241011>;
+		};
+
+		i2s: i2s at 7e203000 {
+			compatible = "brcm,bcm2835-i2s";
+			reg = <0x7e203000 0x20>,
+			      <0x7e101098 0x02>;
+
+			dmas = <&dma 2>,
+			       <&dma 3>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		spi: spi at 7e204000 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204000 0x1000>;
+			interrupts = <2 22>;
+			clocks = <&clk_spi>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c0: i2c at 7e205000 {
+			compatible = "brcm,bcm2835-i2c";
+			reg = <0x7e205000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clk_i2c>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		sdhci: sdhci at 7e300000 {
+			compatible = "brcm,bcm2835-sdhci";
+			reg = <0x7e300000 0x100>;
+			interrupts = <2 30>;
+			clocks = <&clk_mmc>;
+			status = "disabled";
+		};
+
+		i2c1: i2c at 7e804000 {
+			compatible = "brcm,bcm2835-i2c";
+			reg = <0x7e804000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clk_i2c>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		usb at 7e980000 {
+			compatible = "brcm,bcm2835-usb";
+			reg = <0x7e980000 0x10000>;
+			interrupts = <1 9>;
+		};
+
+		arm-pmu {
+			compatible = "arm,arm1176-pmu";
+		};
+	};
+
+	clocks {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		clk_mmc: clock at 0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			#clock-cells = <0>;
+			clock-output-names = "mmc";
+			clock-frequency = <100000000>;
+		};
+
+		clk_i2c: clock at 1 {
+			compatible = "fixed-clock";
+			reg = <1>;
+			#clock-cells = <0>;
+			clock-output-names = "i2c";
+			clock-frequency = <250000000>;
+		};
+
+		clk_spi: clock at 2 {
+			compatible = "fixed-clock";
+			reg = <2>;
+			#clock-cells = <0>;
+			clock-output-names = "spi";
+			clock-frequency = <250000000>;
+		};
+	};
+};
diff --git a/include/dt-bindings/pinctrl/bcm2835.h b/include/dt-bindings/pinctrl/bcm2835.h
new file mode 100644
index 0000000..6f0bc37
--- /dev/null
+++ b/include/dt-bindings/pinctrl/bcm2835.h
@@ -0,0 +1,27 @@
+/*
+ * Header providing constants for bcm2835 pinctrl bindings.
+ *
+ * Copyright (C) 2015 Stefan Wahren <stefan.wahren@i2se.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __DT_BINDINGS_PINCTRL_BCM2835_H__
+#define __DT_BINDINGS_PINCTRL_BCM2835_H__
+
+/* brcm,function property */
+#define BCM2835_FSEL_GPIO_IN	0
+#define BCM2835_FSEL_GPIO_OUT	1
+#define BCM2835_FSEL_ALT5	2
+#define BCM2835_FSEL_ALT4	3
+#define BCM2835_FSEL_ALT0	4
+#define BCM2835_FSEL_ALT1	5
+#define BCM2835_FSEL_ALT2	6
+#define BCM2835_FSEL_ALT3	7
+
+#endif /* __DT_BINDINGS_PINCTRL_BCM2835_H__ */
-- 
2.5.0.rc2.392.g76e840b