[PATCH v2 0/3] MT8173 HDMI 4K support

[PATCH v2 0/3] MT8173 HDMI 4K support

[Bibby Hsieh]

This is MT8173 HDMI 4K support PATCH v2, based on 4.7-rc1.

In order to support HDMI 4K on MT8173,
we have to make some modifications.
1) Make sure that mtk_hdmi_send_infoframe is sent successfully.
2) Enhance the HDMI driving current to improve performance.
3) Make sure that pixel clock is 297MHz when resolution is 4K.

Changes since v1:
 - According to the suggestion from philipp, We use the new
   dpi0_sel rate set method.
 - calls clk_set_rate to set the dpi0_sel according to the
   pixel clock.
 - Remove the direct access to all the intermediate clock part.
 - Remove the intermediate tvdpll_d* clocks in dts.
 - According to suggestion from CK, we rename the clock parse
   function and remove it from mtk_dpi_conf struct.
 - Merges the hdmi Pll set rate for pixel clock greater than
   165MHz and smaller parts.

The PATCH depends on the following patch:
https://patchwork.kernel.org/patch/9249445/ (arm64: dts: mt8173: add mmsel clocks for 4K support)

Thank you.
Bibby Hsieh

Junzhi Zhao (3):
  drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable
  drm/mediatek: enhance the HDMI driving current
  drm/mediatek: fix the wrong pixel clock when resolution is 4K

 drivers/gpu/drm/mediatek/mtk_dpi.c             |  149 +++++++++++++++---------
 drivers/gpu/drm/mediatek/mtk_hdmi.c            |   19 +--
 drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++--
 3 files changed, 138 insertions(+), 72 deletions(-)

-- 
1.7.9.5

[PATCH v2 0/3] MT8173 HDMI 4K support

[Bibby Hsieh]

This is MT8173 HDMI 4K support PATCH v2, based on 4.7-rc1.

In order to support HDMI 4K on MT8173,
we have to make some modifications.
1) Make sure that mtk_hdmi_send_infoframe is sent successfully.
2) Enhance the HDMI driving current to improve performance.
3) Make sure that pixel clock is 297MHz when resolution is 4K.

Changes since v1:
 - According to the suggestion from philipp, We use the new
   dpi0_sel rate set method.
 - calls clk_set_rate to set the dpi0_sel according to the
   pixel clock.
 - Remove the direct access to all the intermediate clock part.
 - Remove the intermediate tvdpll_d* clocks in dts.
 - According to suggestion from CK, we rename the clock parse
   function and remove it from mtk_dpi_conf struct.
 - Merges the hdmi Pll set rate for pixel clock greater than
   165MHz and smaller parts.

The PATCH depends on the following patch:
https://patchwork.kernel.org/patch/9249445/ (arm64: dts: mt8173: add mmsel clocks for 4K support)

Thank you.
Bibby Hsieh

Junzhi Zhao (3):
  drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable
  drm/mediatek: enhance the HDMI driving current
  drm/mediatek: fix the wrong pixel clock when resolution is 4K

 drivers/gpu/drm/mediatek/mtk_dpi.c             |  149 +++++++++++++++---------
 drivers/gpu/drm/mediatek/mtk_hdmi.c            |   19 +--
 drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++--
 3 files changed, 138 insertions(+), 72 deletions(-)

-- 
1.7.9.5

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 0/3] MT8173 HDMI 4K support

[Bibby Hsieh]

This is MT8173 HDMI 4K support PATCH v2, based on 4.7-rc1.

In order to support HDMI 4K on MT8173,
we have to make some modifications.
1) Make sure that mtk_hdmi_send_infoframe is sent successfully.
2) Enhance the HDMI driving current to improve performance.
3) Make sure that pixel clock is 297MHz when resolution is 4K.

Changes since v1:
 - According to the suggestion from philipp, We use the new
   dpi0_sel rate set method.
 - calls clk_set_rate to set the dpi0_sel according to the
   pixel clock.
 - Remove the direct access to all the intermediate clock part.
 - Remove the intermediate tvdpll_d* clocks in dts.
 - According to suggestion from CK, we rename the clock parse
   function and remove it from mtk_dpi_conf struct.
 - Merges the hdmi Pll set rate for pixel clock greater than
   165MHz and smaller parts.

The PATCH depends on the following patch:
https://patchwork.kernel.org/patch/9249445/ (arm64: dts: mt8173: add mmsel clocks for 4K support)

Thank you.
Bibby Hsieh

Junzhi Zhao (3):
  drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable
  drm/mediatek: enhance the HDMI driving current
  drm/mediatek: fix the wrong pixel clock when resolution is 4K

 drivers/gpu/drm/mediatek/mtk_dpi.c             |  149 +++++++++++++++---------
 drivers/gpu/drm/mediatek/mtk_hdmi.c            |   19 +--
 drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++--
 3 files changed, 138 insertions(+), 72 deletions(-)

-- 
1.7.9.5

[PATCH v2 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

The mtk_hdmi_send_infoframe have to
be run after PLL and PIXEL clock of HDMI enable.
Make sure that HDMI inforframes can be sent
successfully.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_hdmi.c |   19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
index ba812ef..d8609f5 100644
--- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
+++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
@@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
 	phy_power_on(hdmi->phy);
 	mtk_hdmi_aud_output_config(hdmi, mode);
 
-	mtk_hdmi_setup_audio_infoframe(hdmi);
-	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
-	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
-	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
-		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
-
 	mtk_hdmi_hw_vid_black(hdmi, false);
 	mtk_hdmi_hw_aud_unmute(hdmi);
 	mtk_hdmi_hw_send_av_unmute(hdmi);
@@ -1401,14 +1395,25 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
 	hdmi->powered = true;
 }
 
+static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
+				    struct drm_display_mode *mode)
+{
+	mtk_hdmi_setup_audio_infoframe(hdmi);
+	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
+	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
+	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
+		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
+}
+
 static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
 {
 	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
 
+	phy_power_on(hdmi->phy);
 	mtk_hdmi_output_set_display_mode(hdmi, &hdmi->mode);
 	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
 	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
-	phy_power_on(hdmi->phy);
+	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
 
 	hdmi->enabled = true;
 }
-- 
1.7.9.5

[PATCH v2 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

The mtk_hdmi_send_infoframe have to
be run after PLL and PIXEL clock of HDMI enable.
Make sure that HDMI inforframes can be sent
successfully.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_hdmi.c |   19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
index ba812ef..d8609f5 100644
--- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
+++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
@@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
 	phy_power_on(hdmi->phy);
 	mtk_hdmi_aud_output_config(hdmi, mode);
 
-	mtk_hdmi_setup_audio_infoframe(hdmi);
-	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
-	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
-	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
-		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
-
 	mtk_hdmi_hw_vid_black(hdmi, false);
 	mtk_hdmi_hw_aud_unmute(hdmi);
 	mtk_hdmi_hw_send_av_unmute(hdmi);
@@ -1401,14 +1395,25 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
 	hdmi->powered = true;
 }
 
+static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
+				    struct drm_display_mode *mode)
+{
+	mtk_hdmi_setup_audio_infoframe(hdmi);
+	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
+	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
+	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
+		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
+}
+
 static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
 {
 	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
 
+	phy_power_on(hdmi->phy);
 	mtk_hdmi_output_set_display_mode(hdmi, &hdmi->mode);
 	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
 	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
-	phy_power_on(hdmi->phy);
+	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
 
 	hdmi->enabled = true;
 }
-- 
1.7.9.5

[PATCH v2 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

The mtk_hdmi_send_infoframe have to
be run after PLL and PIXEL clock of HDMI enable.
Make sure that HDMI inforframes can be sent
successfully.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_hdmi.c |   19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
index ba812ef..d8609f5 100644
--- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
+++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
@@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
 	phy_power_on(hdmi->phy);
 	mtk_hdmi_aud_output_config(hdmi, mode);
 
-	mtk_hdmi_setup_audio_infoframe(hdmi);
-	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
-	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
-	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
-		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
-
 	mtk_hdmi_hw_vid_black(hdmi, false);
 	mtk_hdmi_hw_aud_unmute(hdmi);
 	mtk_hdmi_hw_send_av_unmute(hdmi);
@@ -1401,14 +1395,25 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
 	hdmi->powered = true;
 }
 
+static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
+				    struct drm_display_mode *mode)
+{
+	mtk_hdmi_setup_audio_infoframe(hdmi);
+	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
+	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
+	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
+		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
+}
+
 static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
 {
 	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
 
+	phy_power_on(hdmi->phy);
 	mtk_hdmi_output_set_display_mode(hdmi, &hdmi->mode);
 	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
 	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
-	phy_power_on(hdmi->phy);
+	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
 
 	hdmi->enabled = true;
 }
-- 
1.7.9.5

[PATCH v2 2/3] drm/mediatek: enhance the HDMI driving current

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

In order to improve 4K resolution performance,
we have to enhance the HDMI driving currend
when clock rate is greater than 165MHz.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++++++++++++++-------
 1 file changed, 30 insertions(+), 12 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
index 8a24754..51cb9cf 100644
--- a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
+++ b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
@@ -265,6 +265,9 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 	struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
 	unsigned int pre_div;
 	unsigned int div;
+	unsigned int pre_ibias;
+	unsigned int hdmi_ibias;
+	unsigned int imp_en;
 
 	dev_dbg(hdmi_phy->dev, "%s: %lu Hz, parent: %lu Hz\n", __func__,
 		rate, parent_rate);
@@ -298,18 +301,31 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 			  (0x1 << PLL_BR_SHIFT),
 			  RG_HDMITX_PLL_BP | RG_HDMITX_PLL_BC |
 			  RG_HDMITX_PLL_BR);
-	mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3, RG_HDMITX_PRD_IMP_EN);
+	if (rate < 165000000) {
+		mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3,
+					RG_HDMITX_PRD_IMP_EN);
+		pre_ibias = 0x3;
+		imp_en = 0x0;
+		hdmi_ibias = hdmi_phy->ibias;
+	} else {
+		mtk_hdmi_phy_set_bits(hdmi_phy, HDMI_CON3,
+				      RG_HDMITX_PRD_IMP_EN);
+		pre_ibias = 0x6;
+		imp_en = 0xf;
+		hdmi_ibias = hdmi_phy->ibias_up;
+	}
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON4,
-			  (0x3 << PRD_IBIAS_CLK_SHIFT) |
-			  (0x3 << PRD_IBIAS_D2_SHIFT) |
-			  (0x3 << PRD_IBIAS_D1_SHIFT) |
-			  (0x3 << PRD_IBIAS_D0_SHIFT),
+			  (pre_ibias << PRD_IBIAS_CLK_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D2_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D1_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D0_SHIFT),
 			  RG_HDMITX_PRD_IBIAS_CLK |
 			  RG_HDMITX_PRD_IBIAS_D2 |
 			  RG_HDMITX_PRD_IBIAS_D1 |
 			  RG_HDMITX_PRD_IBIAS_D0);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON3,
-			  (0x0 << DRV_IMP_EN_SHIFT), RG_HDMITX_DRV_IMP_EN);
+			  (imp_en << DRV_IMP_EN_SHIFT),
+			  RG_HDMITX_DRV_IMP_EN);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON6,
 			  (hdmi_phy->drv_imp_clk << DRV_IMP_CLK_SHIFT) |
 			  (hdmi_phy->drv_imp_d2 << DRV_IMP_D2_SHIFT) |
@@ -318,12 +334,14 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 			  RG_HDMITX_DRV_IMP_CLK | RG_HDMITX_DRV_IMP_D2 |
 			  RG_HDMITX_DRV_IMP_D1 | RG_HDMITX_DRV_IMP_D0);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON5,
-			  (hdmi_phy->ibias << DRV_IBIAS_CLK_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D2_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D1_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D0_SHIFT),
-			  RG_HDMITX_DRV_IBIAS_CLK | RG_HDMITX_DRV_IBIAS_D2 |
-			  RG_HDMITX_DRV_IBIAS_D1 | RG_HDMITX_DRV_IBIAS_D0);
+			  (hdmi_ibias << DRV_IBIAS_CLK_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D2_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D1_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D0_SHIFT),
+			  RG_HDMITX_DRV_IBIAS_CLK |
+			  RG_HDMITX_DRV_IBIAS_D2 |
+			  RG_HDMITX_DRV_IBIAS_D1 |
+			  RG_HDMITX_DRV_IBIAS_D0);
 	return 0;
 }
 
-- 
1.7.9.5

[PATCH v2 2/3] drm/mediatek: enhance the HDMI driving current

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

In order to improve 4K resolution performance,
we have to enhance the HDMI driving currend
when clock rate is greater than 165MHz.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++++++++++++++-------
 1 file changed, 30 insertions(+), 12 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
index 8a24754..51cb9cf 100644
--- a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
+++ b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
@@ -265,6 +265,9 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 	struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
 	unsigned int pre_div;
 	unsigned int div;
+	unsigned int pre_ibias;
+	unsigned int hdmi_ibias;
+	unsigned int imp_en;
 
 	dev_dbg(hdmi_phy->dev, "%s: %lu Hz, parent: %lu Hz\n", __func__,
 		rate, parent_rate);
@@ -298,18 +301,31 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 			  (0x1 << PLL_BR_SHIFT),
 			  RG_HDMITX_PLL_BP | RG_HDMITX_PLL_BC |
 			  RG_HDMITX_PLL_BR);
-	mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3, RG_HDMITX_PRD_IMP_EN);
+	if (rate < 165000000) {
+		mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3,
+					RG_HDMITX_PRD_IMP_EN);
+		pre_ibias = 0x3;
+		imp_en = 0x0;
+		hdmi_ibias = hdmi_phy->ibias;
+	} else {
+		mtk_hdmi_phy_set_bits(hdmi_phy, HDMI_CON3,
+				      RG_HDMITX_PRD_IMP_EN);
+		pre_ibias = 0x6;
+		imp_en = 0xf;
+		hdmi_ibias = hdmi_phy->ibias_up;
+	}
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON4,
-			  (0x3 << PRD_IBIAS_CLK_SHIFT) |
-			  (0x3 << PRD_IBIAS_D2_SHIFT) |
-			  (0x3 << PRD_IBIAS_D1_SHIFT) |
-			  (0x3 << PRD_IBIAS_D0_SHIFT),
+			  (pre_ibias << PRD_IBIAS_CLK_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D2_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D1_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D0_SHIFT),
 			  RG_HDMITX_PRD_IBIAS_CLK |
 			  RG_HDMITX_PRD_IBIAS_D2 |
 			  RG_HDMITX_PRD_IBIAS_D1 |
 			  RG_HDMITX_PRD_IBIAS_D0);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON3,
-			  (0x0 << DRV_IMP_EN_SHIFT), RG_HDMITX_DRV_IMP_EN);
+			  (imp_en << DRV_IMP_EN_SHIFT),
+			  RG_HDMITX_DRV_IMP_EN);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON6,
 			  (hdmi_phy->drv_imp_clk << DRV_IMP_CLK_SHIFT) |
 			  (hdmi_phy->drv_imp_d2 << DRV_IMP_D2_SHIFT) |
@@ -318,12 +334,14 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 			  RG_HDMITX_DRV_IMP_CLK | RG_HDMITX_DRV_IMP_D2 |
 			  RG_HDMITX_DRV_IMP_D1 | RG_HDMITX_DRV_IMP_D0);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON5,
-			  (hdmi_phy->ibias << DRV_IBIAS_CLK_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D2_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D1_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D0_SHIFT),
-			  RG_HDMITX_DRV_IBIAS_CLK | RG_HDMITX_DRV_IBIAS_D2 |
-			  RG_HDMITX_DRV_IBIAS_D1 | RG_HDMITX_DRV_IBIAS_D0);
+			  (hdmi_ibias << DRV_IBIAS_CLK_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D2_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D1_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D0_SHIFT),
+			  RG_HDMITX_DRV_IBIAS_CLK |
+			  RG_HDMITX_DRV_IBIAS_D2 |
+			  RG_HDMITX_DRV_IBIAS_D1 |
+			  RG_HDMITX_DRV_IBIAS_D0);
 	return 0;
 }
 
-- 
1.7.9.5

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 2/3] drm/mediatek: enhance the HDMI driving current

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

In order to improve 4K resolution performance,
we have to enhance the HDMI driving currend
when clock rate is greater than 165MHz.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++++++++++++++-------
 1 file changed, 30 insertions(+), 12 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
index 8a24754..51cb9cf 100644
--- a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
+++ b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
@@ -265,6 +265,9 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 	struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
 	unsigned int pre_div;
 	unsigned int div;
+	unsigned int pre_ibias;
+	unsigned int hdmi_ibias;
+	unsigned int imp_en;
 
 	dev_dbg(hdmi_phy->dev, "%s: %lu Hz, parent: %lu Hz\n", __func__,
 		rate, parent_rate);
@@ -298,18 +301,31 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 			  (0x1 << PLL_BR_SHIFT),
 			  RG_HDMITX_PLL_BP | RG_HDMITX_PLL_BC |
 			  RG_HDMITX_PLL_BR);
-	mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3, RG_HDMITX_PRD_IMP_EN);
+	if (rate < 165000000) {
+		mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3,
+					RG_HDMITX_PRD_IMP_EN);
+		pre_ibias = 0x3;
+		imp_en = 0x0;
+		hdmi_ibias = hdmi_phy->ibias;
+	} else {
+		mtk_hdmi_phy_set_bits(hdmi_phy, HDMI_CON3,
+				      RG_HDMITX_PRD_IMP_EN);
+		pre_ibias = 0x6;
+		imp_en = 0xf;
+		hdmi_ibias = hdmi_phy->ibias_up;
+	}
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON4,
-			  (0x3 << PRD_IBIAS_CLK_SHIFT) |
-			  (0x3 << PRD_IBIAS_D2_SHIFT) |
-			  (0x3 << PRD_IBIAS_D1_SHIFT) |
-			  (0x3 << PRD_IBIAS_D0_SHIFT),
+			  (pre_ibias << PRD_IBIAS_CLK_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D2_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D1_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D0_SHIFT),
 			  RG_HDMITX_PRD_IBIAS_CLK |
 			  RG_HDMITX_PRD_IBIAS_D2 |
 			  RG_HDMITX_PRD_IBIAS_D1 |
 			  RG_HDMITX_PRD_IBIAS_D0);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON3,
-			  (0x0 << DRV_IMP_EN_SHIFT), RG_HDMITX_DRV_IMP_EN);
+			  (imp_en << DRV_IMP_EN_SHIFT),
+			  RG_HDMITX_DRV_IMP_EN);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON6,
 			  (hdmi_phy->drv_imp_clk << DRV_IMP_CLK_SHIFT) |
 			  (hdmi_phy->drv_imp_d2 << DRV_IMP_D2_SHIFT) |
@@ -318,12 +334,14 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 			  RG_HDMITX_DRV_IMP_CLK | RG_HDMITX_DRV_IMP_D2 |
 			  RG_HDMITX_DRV_IMP_D1 | RG_HDMITX_DRV_IMP_D0);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON5,
-			  (hdmi_phy->ibias << DRV_IBIAS_CLK_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D2_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D1_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D0_SHIFT),
-			  RG_HDMITX_DRV_IBIAS_CLK | RG_HDMITX_DRV_IBIAS_D2 |
-			  RG_HDMITX_DRV_IBIAS_D1 | RG_HDMITX_DRV_IBIAS_D0);
+			  (hdmi_ibias << DRV_IBIAS_CLK_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D2_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D1_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D0_SHIFT),
+			  RG_HDMITX_DRV_IBIAS_CLK |
+			  RG_HDMITX_DRV_IBIAS_D2 |
+			  RG_HDMITX_DRV_IBIAS_D1 |
+			  RG_HDMITX_DRV_IBIAS_D0);
 	return 0;
 }
 
-- 
1.7.9.5

[PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

Pixel clock should be 297MHz when resolution is 4K.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
 1 file changed, 96 insertions(+), 53 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index d05ca79..fa390e0 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
 	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
 };
 
+enum mtk_dpi_clk_id {
+	MTK_DPI_CLK_DPI_ENGINE,
+	MTK_DPI_CLK_DPI_PIXEL,
+	MTK_DPI_CLK_TVD_PLL,
+	MTK_DPI_CLK_COUNT,
+};
+
+static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
+	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
+	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
+	[MTK_DPI_CLK_TVD_PLL] = "pll",
+};
+
 struct mtk_dpi {
 	struct mtk_ddp_comp ddp_comp;
 	struct drm_encoder encoder;
 	void __iomem *regs;
 	struct device *dev;
-	struct clk *engine_clk;
-	struct clk *pixel_clk;
-	struct clk *tvd_clk;
+	struct clk *clk[MTK_DPI_CLK_COUNT];
 	int irq;
 	struct drm_display_mode mode;
 	enum mtk_dpi_out_color_format color_format;
@@ -76,6 +87,7 @@ struct mtk_dpi {
 	enum mtk_dpi_out_channel_swap channel_swap;
 	bool power_sta;
 	u8 power_ctl;
+	void *data;
 };
 
 static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
@@ -114,6 +126,10 @@ struct mtk_dpi_yc_limit {
 	u16 c_bottom;
 };
 
+struct mtk_dpi_conf {
+	int (*clk_config)(struct mtk_dpi *dpi, struct drm_display_mode *mode);
+};
+
 static void mtk_dpi_mask(struct mtk_dpi *dpi, u32 offset, u32 val, u32 mask)
 {
 	u32 tmp = readl(dpi->regs + offset) & ~mask;
@@ -377,8 +393,8 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
 		return;
 
 	mtk_dpi_disable(dpi);
-	clk_disable_unprepare(dpi->pixel_clk);
-	clk_disable_unprepare(dpi->engine_clk);
+	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
+	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
 	dpi->power_sta = false;
 }
 
@@ -395,13 +411,13 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
 	if (dpi->power_sta)
 		return 0;
 
-	ret = clk_prepare_enable(dpi->engine_clk);
+	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
 	if (ret) {
 		dev_err(dpi->dev, "Failed to enable engine clock: %d\n", ret);
 		goto err_eng;
 	}
 
-	ret = clk_prepare_enable(dpi->pixel_clk);
+	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
 	if (ret) {
 		dev_err(dpi->dev, "Failed to enable pixel clock: %d\n", ret);
 		goto err_pixel;
@@ -412,7 +428,7 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
 	return 0;
 
 err_pixel:
-	clk_disable_unprepare(dpi->engine_clk);
+	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
 err_eng:
 	dpi->power_ctl &= ~pctl;
 	return ret;
@@ -428,34 +444,18 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	struct mtk_dpi_sync_param vsync_leven = { 0 };
 	struct mtk_dpi_sync_param vsync_rodd = { 0 };
 	struct mtk_dpi_sync_param vsync_reven = { 0 };
-	unsigned long pix_rate;
-	unsigned long pll_rate;
-	unsigned int factor;
+	struct mtk_dpi_conf *conf;
+	int ret;
 
 	if (!dpi) {
 		dev_err(dpi->dev, "invalid argument\n");
 		return -EINVAL;
 	}
 
-	pix_rate = 1000UL * mode->clock;
-	if (mode->clock <= 74000)
-		factor = 8 * 3;
-	else
-		factor = 4 * 3;
-	pll_rate = pix_rate * factor;
-
-	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
-		pll_rate, pix_rate);
-
-	clk_set_rate(dpi->tvd_clk, pll_rate);
-	pll_rate = clk_get_rate(dpi->tvd_clk);
-
-	pix_rate = pll_rate / factor;
-	clk_set_rate(dpi->pixel_clk, pix_rate);
-	pix_rate = clk_get_rate(dpi->pixel_clk);
-
-	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
-		pll_rate, pix_rate);
+	conf = (struct mtk_dpi_conf *)dpi->data;
+	ret = conf->clk_config(dpi, mode);
+	if (ret)
+		dev_err(dpi->dev, "dpi clk set fail\n");
 
 	limit.c_bottom = 0x0010;
 	limit.c_top = 0x0FE0;
@@ -656,20 +656,83 @@ static const struct component_ops mtk_dpi_component_ops = {
 	.unbind = mtk_dpi_unbind,
 };
 
+static int mtk_dpi_parse_clk_from_dt(struct mtk_dpi *dpi,
+				     struct device_node *np)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(mtk_dpi_clk_names); i++) {
+		dpi->clk[i] = of_clk_get_by_name(np,
+						  mtk_dpi_clk_names[i]);
+		if (IS_ERR(dpi->clk[i]))
+			return PTR_ERR(dpi->clk[i]);
+	}
+	return 0;
+}
+
+static int mt8173_clk_config(struct mtk_dpi *dpi, struct drm_display_mode *mode)
+{
+	unsigned long pix_rate;
+	unsigned long pll_rate;
+	unsigned int factor;
+
+	pix_rate = 1000UL * mode->clock;
+	if (mode->clock <= 27000)
+		factor = 16 * 3;
+	else if (mode->clock <= 74250)
+		factor = 8 * 3;
+	else if (mode->clock <= 167000)
+		factor = 4 * 3;
+	else
+		factor = 2 * 3;
+	pll_rate = pix_rate * factor;
+
+	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
+		pll_rate, pix_rate);
+
+	pll_rate = clk_get_rate(dpi->clk[MTK_DPI_CLK_TVD_PLL]);
+	pix_rate = pll_rate / factor;
+	clk_set_rate(dpi->clk[MTK_DPI_CLK_DPI_PIXEL], pix_rate);
+	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
+		pll_rate, pix_rate);
+
+	return 0;
+}
+
+static const struct mtk_dpi_conf mt8173_conf = {
+	.clk_config = mt8173_clk_config,
+};
+
+static const struct of_device_id mtk_dpi_of_ids[] = {
+	{ .compatible = "mediatek,mt8173-dpi",
+		.data = &mt8173_conf,
+	},
+	{}
+};
+
 static int mtk_dpi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct mtk_dpi *dpi;
 	struct resource *mem;
+	struct device_node *np = dev->of_node;
 	struct device_node *ep, *bridge_node = NULL;
 	int comp_id;
+	const struct of_device_id *match;
+	struct mtk_dpi_conf *conf;
 	int ret;
 
+	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
+	if (!match)
+		return -ENODEV;
+
 	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
 	if (!dpi)
 		return -ENOMEM;
 
 	dpi->dev = dev;
+	dpi->data = (void *)match->data;
+	conf = (struct mtk_dpi_conf *)match->data;
 
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dpi->regs = devm_ioremap_resource(dev, mem);
@@ -679,24 +742,9 @@ static int mtk_dpi_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	dpi->engine_clk = devm_clk_get(dev, "engine");
-	if (IS_ERR(dpi->engine_clk)) {
-		ret = PTR_ERR(dpi->engine_clk);
-		dev_err(dev, "Failed to get engine clock: %d\n", ret);
-		return ret;
-	}
-
-	dpi->pixel_clk = devm_clk_get(dev, "pixel");
-	if (IS_ERR(dpi->pixel_clk)) {
-		ret = PTR_ERR(dpi->pixel_clk);
-		dev_err(dev, "Failed to get pixel clock: %d\n", ret);
-		return ret;
-	}
-
-	dpi->tvd_clk = devm_clk_get(dev, "pll");
-	if (IS_ERR(dpi->tvd_clk)) {
-		ret = PTR_ERR(dpi->tvd_clk);
-		dev_err(dev, "Failed to get tvdpll clock: %d\n", ret);
+	ret = mtk_dpi_parse_clk_from_dt(dpi, np);
+	if (ret) {
+		dev_err(dev, "parse tvd div clk failed!");
 		return ret;
 	}
 
@@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
 	return 0;
 }
 
-static const struct of_device_id mtk_dpi_of_ids[] = {
-	{ .compatible = "mediatek,mt8173-dpi", },
-	{}
-};
-
 struct platform_driver mtk_dpi_driver = {
 	.probe = mtk_dpi_probe,
 	.remove = mtk_dpi_remove,
-- 
1.7.9.5

[PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

Pixel clock should be 297MHz when resolution is 4K.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
 1 file changed, 96 insertions(+), 53 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index d05ca79..fa390e0 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
 	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
 };
 
+enum mtk_dpi_clk_id {
+	MTK_DPI_CLK_DPI_ENGINE,
+	MTK_DPI_CLK_DPI_PIXEL,
+	MTK_DPI_CLK_TVD_PLL,
+	MTK_DPI_CLK_COUNT,
+};
+
+static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
+	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
+	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
+	[MTK_DPI_CLK_TVD_PLL] = "pll",
+};
+
 struct mtk_dpi {
 	struct mtk_ddp_comp ddp_comp;
 	struct drm_encoder encoder;
 	void __iomem *regs;
 	struct device *dev;
-	struct clk *engine_clk;
-	struct clk *pixel_clk;
-	struct clk *tvd_clk;
+	struct clk *clk[MTK_DPI_CLK_COUNT];
 	int irq;
 	struct drm_display_mode mode;
 	enum mtk_dpi_out_color_format color_format;
@@ -76,6 +87,7 @@ struct mtk_dpi {
 	enum mtk_dpi_out_channel_swap channel_swap;
 	bool power_sta;
 	u8 power_ctl;
+	void *data;
 };
 
 static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
@@ -114,6 +126,10 @@ struct mtk_dpi_yc_limit {
 	u16 c_bottom;
 };
 
+struct mtk_dpi_conf {
+	int (*clk_config)(struct mtk_dpi *dpi, struct drm_display_mode *mode);
+};
+
 static void mtk_dpi_mask(struct mtk_dpi *dpi, u32 offset, u32 val, u32 mask)
 {
 	u32 tmp = readl(dpi->regs + offset) & ~mask;
@@ -377,8 +393,8 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
 		return;
 
 	mtk_dpi_disable(dpi);
-	clk_disable_unprepare(dpi->pixel_clk);
-	clk_disable_unprepare(dpi->engine_clk);
+	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
+	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
 	dpi->power_sta = false;
 }
 
@@ -395,13 +411,13 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
 	if (dpi->power_sta)
 		return 0;
 
-	ret = clk_prepare_enable(dpi->engine_clk);
+	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
 	if (ret) {
 		dev_err(dpi->dev, "Failed to enable engine clock: %d\n", ret);
 		goto err_eng;
 	}
 
-	ret = clk_prepare_enable(dpi->pixel_clk);
+	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
 	if (ret) {
 		dev_err(dpi->dev, "Failed to enable pixel clock: %d\n", ret);
 		goto err_pixel;
@@ -412,7 +428,7 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
 	return 0;
 
 err_pixel:
-	clk_disable_unprepare(dpi->engine_clk);
+	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
 err_eng:
 	dpi->power_ctl &= ~pctl;
 	return ret;
@@ -428,34 +444,18 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	struct mtk_dpi_sync_param vsync_leven = { 0 };
 	struct mtk_dpi_sync_param vsync_rodd = { 0 };
 	struct mtk_dpi_sync_param vsync_reven = { 0 };
-	unsigned long pix_rate;
-	unsigned long pll_rate;
-	unsigned int factor;
+	struct mtk_dpi_conf *conf;
+	int ret;
 
 	if (!dpi) {
 		dev_err(dpi->dev, "invalid argument\n");
 		return -EINVAL;
 	}
 
-	pix_rate = 1000UL * mode->clock;
-	if (mode->clock <= 74000)
-		factor = 8 * 3;
-	else
-		factor = 4 * 3;
-	pll_rate = pix_rate * factor;
-
-	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
-		pll_rate, pix_rate);
-
-	clk_set_rate(dpi->tvd_clk, pll_rate);
-	pll_rate = clk_get_rate(dpi->tvd_clk);
-
-	pix_rate = pll_rate / factor;
-	clk_set_rate(dpi->pixel_clk, pix_rate);
-	pix_rate = clk_get_rate(dpi->pixel_clk);
-
-	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
-		pll_rate, pix_rate);
+	conf = (struct mtk_dpi_conf *)dpi->data;
+	ret = conf->clk_config(dpi, mode);
+	if (ret)
+		dev_err(dpi->dev, "dpi clk set fail\n");
 
 	limit.c_bottom = 0x0010;
 	limit.c_top = 0x0FE0;
@@ -656,20 +656,83 @@ static const struct component_ops mtk_dpi_component_ops = {
 	.unbind = mtk_dpi_unbind,
 };
 
+static int mtk_dpi_parse_clk_from_dt(struct mtk_dpi *dpi,
+				     struct device_node *np)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(mtk_dpi_clk_names); i++) {
+		dpi->clk[i] = of_clk_get_by_name(np,
+						  mtk_dpi_clk_names[i]);
+		if (IS_ERR(dpi->clk[i]))
+			return PTR_ERR(dpi->clk[i]);
+	}
+	return 0;
+}
+
+static int mt8173_clk_config(struct mtk_dpi *dpi, struct drm_display_mode *mode)
+{
+	unsigned long pix_rate;
+	unsigned long pll_rate;
+	unsigned int factor;
+
+	pix_rate = 1000UL * mode->clock;
+	if (mode->clock <= 27000)
+		factor = 16 * 3;
+	else if (mode->clock <= 74250)
+		factor = 8 * 3;
+	else if (mode->clock <= 167000)
+		factor = 4 * 3;
+	else
+		factor = 2 * 3;
+	pll_rate = pix_rate * factor;
+
+	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
+		pll_rate, pix_rate);
+
+	pll_rate = clk_get_rate(dpi->clk[MTK_DPI_CLK_TVD_PLL]);
+	pix_rate = pll_rate / factor;
+	clk_set_rate(dpi->clk[MTK_DPI_CLK_DPI_PIXEL], pix_rate);
+	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
+		pll_rate, pix_rate);
+
+	return 0;
+}
+
+static const struct mtk_dpi_conf mt8173_conf = {
+	.clk_config = mt8173_clk_config,
+};
+
+static const struct of_device_id mtk_dpi_of_ids[] = {
+	{ .compatible = "mediatek,mt8173-dpi",
+		.data = &mt8173_conf,
+	},
+	{}
+};
+
 static int mtk_dpi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct mtk_dpi *dpi;
 	struct resource *mem;
+	struct device_node *np = dev->of_node;
 	struct device_node *ep, *bridge_node = NULL;
 	int comp_id;
+	const struct of_device_id *match;
+	struct mtk_dpi_conf *conf;
 	int ret;
 
+	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
+	if (!match)
+		return -ENODEV;
+
 	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
 	if (!dpi)
 		return -ENOMEM;
 
 	dpi->dev = dev;
+	dpi->data = (void *)match->data;
+	conf = (struct mtk_dpi_conf *)match->data;
 
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dpi->regs = devm_ioremap_resource(dev, mem);
@@ -679,24 +742,9 @@ static int mtk_dpi_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	dpi->engine_clk = devm_clk_get(dev, "engine");
-	if (IS_ERR(dpi->engine_clk)) {
-		ret = PTR_ERR(dpi->engine_clk);
-		dev_err(dev, "Failed to get engine clock: %d\n", ret);
-		return ret;
-	}
-
-	dpi->pixel_clk = devm_clk_get(dev, "pixel");
-	if (IS_ERR(dpi->pixel_clk)) {
-		ret = PTR_ERR(dpi->pixel_clk);
-		dev_err(dev, "Failed to get pixel clock: %d\n", ret);
-		return ret;
-	}
-
-	dpi->tvd_clk = devm_clk_get(dev, "pll");
-	if (IS_ERR(dpi->tvd_clk)) {
-		ret = PTR_ERR(dpi->tvd_clk);
-		dev_err(dev, "Failed to get tvdpll clock: %d\n", ret);
+	ret = mtk_dpi_parse_clk_from_dt(dpi, np);
+	if (ret) {
+		dev_err(dev, "parse tvd div clk failed!");
 		return ret;
 	}
 
@@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
 	return 0;
 }
 
-static const struct of_device_id mtk_dpi_of_ids[] = {
-	{ .compatible = "mediatek,mt8173-dpi", },
-	{}
-};
-
 struct platform_driver mtk_dpi_driver = {
 	.probe = mtk_dpi_probe,
 	.remove = mtk_dpi_remove,
-- 
1.7.9.5

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

Pixel clock should be 297MHz when resolution is 4K.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
 1 file changed, 96 insertions(+), 53 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index d05ca79..fa390e0 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
 	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
 };
 
+enum mtk_dpi_clk_id {
+	MTK_DPI_CLK_DPI_ENGINE,
+	MTK_DPI_CLK_DPI_PIXEL,
+	MTK_DPI_CLK_TVD_PLL,
+	MTK_DPI_CLK_COUNT,
+};
+
+static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
+	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
+	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
+	[MTK_DPI_CLK_TVD_PLL] = "pll",
+};
+
 struct mtk_dpi {
 	struct mtk_ddp_comp ddp_comp;
 	struct drm_encoder encoder;
 	void __iomem *regs;
 	struct device *dev;
-	struct clk *engine_clk;
-	struct clk *pixel_clk;
-	struct clk *tvd_clk;
+	struct clk *clk[MTK_DPI_CLK_COUNT];
 	int irq;
 	struct drm_display_mode mode;
 	enum mtk_dpi_out_color_format color_format;
@@ -76,6 +87,7 @@ struct mtk_dpi {
 	enum mtk_dpi_out_channel_swap channel_swap;
 	bool power_sta;
 	u8 power_ctl;
+	void *data;
 };
 
 static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
@@ -114,6 +126,10 @@ struct mtk_dpi_yc_limit {
 	u16 c_bottom;
 };
 
+struct mtk_dpi_conf {
+	int (*clk_config)(struct mtk_dpi *dpi, struct drm_display_mode *mode);
+};
+
 static void mtk_dpi_mask(struct mtk_dpi *dpi, u32 offset, u32 val, u32 mask)
 {
 	u32 tmp = readl(dpi->regs + offset) & ~mask;
@@ -377,8 +393,8 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
 		return;
 
 	mtk_dpi_disable(dpi);
-	clk_disable_unprepare(dpi->pixel_clk);
-	clk_disable_unprepare(dpi->engine_clk);
+	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
+	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
 	dpi->power_sta = false;
 }
 
@@ -395,13 +411,13 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
 	if (dpi->power_sta)
 		return 0;
 
-	ret = clk_prepare_enable(dpi->engine_clk);
+	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
 	if (ret) {
 		dev_err(dpi->dev, "Failed to enable engine clock: %d\n", ret);
 		goto err_eng;
 	}
 
-	ret = clk_prepare_enable(dpi->pixel_clk);
+	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
 	if (ret) {
 		dev_err(dpi->dev, "Failed to enable pixel clock: %d\n", ret);
 		goto err_pixel;
@@ -412,7 +428,7 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
 	return 0;
 
 err_pixel:
-	clk_disable_unprepare(dpi->engine_clk);
+	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
 err_eng:
 	dpi->power_ctl &= ~pctl;
 	return ret;
@@ -428,34 +444,18 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	struct mtk_dpi_sync_param vsync_leven = { 0 };
 	struct mtk_dpi_sync_param vsync_rodd = { 0 };
 	struct mtk_dpi_sync_param vsync_reven = { 0 };
-	unsigned long pix_rate;
-	unsigned long pll_rate;
-	unsigned int factor;
+	struct mtk_dpi_conf *conf;
+	int ret;
 
 	if (!dpi) {
 		dev_err(dpi->dev, "invalid argument\n");
 		return -EINVAL;
 	}
 
-	pix_rate = 1000UL * mode->clock;
-	if (mode->clock <= 74000)
-		factor = 8 * 3;
-	else
-		factor = 4 * 3;
-	pll_rate = pix_rate * factor;
-
-	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
-		pll_rate, pix_rate);
-
-	clk_set_rate(dpi->tvd_clk, pll_rate);
-	pll_rate = clk_get_rate(dpi->tvd_clk);
-
-	pix_rate = pll_rate / factor;
-	clk_set_rate(dpi->pixel_clk, pix_rate);
-	pix_rate = clk_get_rate(dpi->pixel_clk);
-
-	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
-		pll_rate, pix_rate);
+	conf = (struct mtk_dpi_conf *)dpi->data;
+	ret = conf->clk_config(dpi, mode);
+	if (ret)
+		dev_err(dpi->dev, "dpi clk set fail\n");
 
 	limit.c_bottom = 0x0010;
 	limit.c_top = 0x0FE0;
@@ -656,20 +656,83 @@ static const struct component_ops mtk_dpi_component_ops = {
 	.unbind = mtk_dpi_unbind,
 };
 
+static int mtk_dpi_parse_clk_from_dt(struct mtk_dpi *dpi,
+				     struct device_node *np)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(mtk_dpi_clk_names); i++) {
+		dpi->clk[i] = of_clk_get_by_name(np,
+						  mtk_dpi_clk_names[i]);
+		if (IS_ERR(dpi->clk[i]))
+			return PTR_ERR(dpi->clk[i]);
+	}
+	return 0;
+}
+
+static int mt8173_clk_config(struct mtk_dpi *dpi, struct drm_display_mode *mode)
+{
+	unsigned long pix_rate;
+	unsigned long pll_rate;
+	unsigned int factor;
+
+	pix_rate = 1000UL * mode->clock;
+	if (mode->clock <= 27000)
+		factor = 16 * 3;
+	else if (mode->clock <= 74250)
+		factor = 8 * 3;
+	else if (mode->clock <= 167000)
+		factor = 4 * 3;
+	else
+		factor = 2 * 3;
+	pll_rate = pix_rate * factor;
+
+	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
+		pll_rate, pix_rate);
+
+	pll_rate = clk_get_rate(dpi->clk[MTK_DPI_CLK_TVD_PLL]);
+	pix_rate = pll_rate / factor;
+	clk_set_rate(dpi->clk[MTK_DPI_CLK_DPI_PIXEL], pix_rate);
+	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
+		pll_rate, pix_rate);
+
+	return 0;
+}
+
+static const struct mtk_dpi_conf mt8173_conf = {
+	.clk_config = mt8173_clk_config,
+};
+
+static const struct of_device_id mtk_dpi_of_ids[] = {
+	{ .compatible = "mediatek,mt8173-dpi",
+		.data = &mt8173_conf,
+	},
+	{}
+};
+
 static int mtk_dpi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct mtk_dpi *dpi;
 	struct resource *mem;
+	struct device_node *np = dev->of_node;
 	struct device_node *ep, *bridge_node = NULL;
 	int comp_id;
+	const struct of_device_id *match;
+	struct mtk_dpi_conf *conf;
 	int ret;
 
+	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
+	if (!match)
+		return -ENODEV;
+
 	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
 	if (!dpi)
 		return -ENOMEM;
 
 	dpi->dev = dev;
+	dpi->data = (void *)match->data;
+	conf = (struct mtk_dpi_conf *)match->data;
 
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dpi->regs = devm_ioremap_resource(dev, mem);
@@ -679,24 +742,9 @@ static int mtk_dpi_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	dpi->engine_clk = devm_clk_get(dev, "engine");
-	if (IS_ERR(dpi->engine_clk)) {
-		ret = PTR_ERR(dpi->engine_clk);
-		dev_err(dev, "Failed to get engine clock: %d\n", ret);
-		return ret;
-	}
-
-	dpi->pixel_clk = devm_clk_get(dev, "pixel");
-	if (IS_ERR(dpi->pixel_clk)) {
-		ret = PTR_ERR(dpi->pixel_clk);
-		dev_err(dev, "Failed to get pixel clock: %d\n", ret);
-		return ret;
-	}
-
-	dpi->tvd_clk = devm_clk_get(dev, "pll");
-	if (IS_ERR(dpi->tvd_clk)) {
-		ret = PTR_ERR(dpi->tvd_clk);
-		dev_err(dev, "Failed to get tvdpll clock: %d\n", ret);
+	ret = mtk_dpi_parse_clk_from_dt(dpi, np);
+	if (ret) {
+		dev_err(dev, "parse tvd div clk failed!");
 		return ret;
 	}
 
@@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
 	return 0;
 }
 
-static const struct of_device_id mtk_dpi_of_ids[] = {
-	{ .compatible = "mediatek,mt8173-dpi", },
-	{}
-};
-
 struct platform_driver mtk_dpi_driver = {
 	.probe = mtk_dpi_probe,
 	.remove = mtk_dpi_remove,
-- 
1.7.9.5

Re: [PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Philipp Zabel]

Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> Pixel clock should be 297MHz when resolution is 4K.

This patch does two different things, please don't conflate them.

First, it adds support for 16*3 and 2*3 factors between PLL and pixel
clock. This should be a separate patch and does what this patch
description says.

The second part moves the clocks into an array and adds an indirection
to clock registration depending on of_match_node. This should be a
separate patch. I suppose this change is in preparation for mt2701
support, but I'm not sure yet if it is needed at all.

regards
Philipp

> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
>  1 file changed, 96 insertions(+), 53 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index d05ca79..fa390e0 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
>  	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
>  };
>  
> +enum mtk_dpi_clk_id {
> +	MTK_DPI_CLK_DPI_ENGINE,
> +	MTK_DPI_CLK_DPI_PIXEL,
> +	MTK_DPI_CLK_TVD_PLL,
> +	MTK_DPI_CLK_COUNT,
> +};
> +
> +static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
> +	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
> +	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
> +	[MTK_DPI_CLK_TVD_PLL] = "pll",
> +};
> +
>  struct mtk_dpi {
>  	struct mtk_ddp_comp ddp_comp;
>  	struct drm_encoder encoder;
>  	void __iomem *regs;
>  	struct device *dev;
> -	struct clk *engine_clk;
> -	struct clk *pixel_clk;
> -	struct clk *tvd_clk;
> +	struct clk *clk[MTK_DPI_CLK_COUNT];
>  	int irq;
>  	struct drm_display_mode mode;
>  	enum mtk_dpi_out_color_format color_format;
> @@ -76,6 +87,7 @@ struct mtk_dpi {
>  	enum mtk_dpi_out_channel_swap channel_swap;
>  	bool power_sta;
>  	u8 power_ctl;
> +	void *data;
>  };
>  
>  static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
> @@ -114,6 +126,10 @@ struct mtk_dpi_yc_limit {
>  	u16 c_bottom;
>  };
>  
> +struct mtk_dpi_conf {
> +	int (*clk_config)(struct mtk_dpi *dpi, struct drm_display_mode *mode);
> +};
> +
>  static void mtk_dpi_mask(struct mtk_dpi *dpi, u32 offset, u32 val, u32 mask)
>  {
>  	u32 tmp = readl(dpi->regs + offset) & ~mask;
> @@ -377,8 +393,8 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
>  		return;
>  
>  	mtk_dpi_disable(dpi);
> -	clk_disable_unprepare(dpi->pixel_clk);
> -	clk_disable_unprepare(dpi->engine_clk);
> +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
> +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
>  	dpi->power_sta = false;
>  }
>  
> @@ -395,13 +411,13 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
>  	if (dpi->power_sta)
>  		return 0;
>  
> -	ret = clk_prepare_enable(dpi->engine_clk);
> +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
>  	if (ret) {
>  		dev_err(dpi->dev, "Failed to enable engine clock: %d\n", ret);
>  		goto err_eng;
>  	}
>  
> -	ret = clk_prepare_enable(dpi->pixel_clk);
> +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
>  	if (ret) {
>  		dev_err(dpi->dev, "Failed to enable pixel clock: %d\n", ret);
>  		goto err_pixel;
> @@ -412,7 +428,7 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
>  	return 0;
>  
>  err_pixel:
> -	clk_disable_unprepare(dpi->engine_clk);
> +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
>  err_eng:
>  	dpi->power_ctl &= ~pctl;
>  	return ret;
> @@ -428,34 +444,18 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
>  	struct mtk_dpi_sync_param vsync_leven = { 0 };
>  	struct mtk_dpi_sync_param vsync_rodd = { 0 };
>  	struct mtk_dpi_sync_param vsync_reven = { 0 };
> -	unsigned long pix_rate;
> -	unsigned long pll_rate;
> -	unsigned int factor;
> +	struct mtk_dpi_conf *conf;
> +	int ret;
>  
>  	if (!dpi) {
>  		dev_err(dpi->dev, "invalid argument\n");
>  		return -EINVAL;
>  	}
>  
> -	pix_rate = 1000UL * mode->clock;
> -	if (mode->clock <= 74000)
> -		factor = 8 * 3;
> -	else
> -		factor = 4 * 3;
> -	pll_rate = pix_rate * factor;
> -
> -	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> -		pll_rate, pix_rate);
> -
> -	clk_set_rate(dpi->tvd_clk, pll_rate);
> -	pll_rate = clk_get_rate(dpi->tvd_clk);
> -
> -	pix_rate = pll_rate / factor;
> -	clk_set_rate(dpi->pixel_clk, pix_rate);
> -	pix_rate = clk_get_rate(dpi->pixel_clk);
> -
> -	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> -		pll_rate, pix_rate);
> +	conf = (struct mtk_dpi_conf *)dpi->data;
> +	ret = conf->clk_config(dpi, mode);
> +	if (ret)
> +		dev_err(dpi->dev, "dpi clk set fail\n");
>  
>  	limit.c_bottom = 0x0010;
>  	limit.c_top = 0x0FE0;
> @@ -656,20 +656,83 @@ static const struct component_ops mtk_dpi_component_ops = {
>  	.unbind = mtk_dpi_unbind,
>  };
>  
> +static int mtk_dpi_parse_clk_from_dt(struct mtk_dpi *dpi,
> +				     struct device_node *np)
> +{
> +	int i;
> +
> +	for (i = 0; i < ARRAY_SIZE(mtk_dpi_clk_names); i++) {
> +		dpi->clk[i] = of_clk_get_by_name(np,
> +						  mtk_dpi_clk_names[i]);
> +		if (IS_ERR(dpi->clk[i]))
> +			return PTR_ERR(dpi->clk[i]);
> +	}
> +	return 0;
> +}
> +
> +static int mt8173_clk_config(struct mtk_dpi *dpi, struct drm_display_mode *mode)
> +{
> +	unsigned long pix_rate;
> +	unsigned long pll_rate;
> +	unsigned int factor;
> +
> +	pix_rate = 1000UL * mode->clock;
> +	if (mode->clock <= 27000)
> +		factor = 16 * 3;
> +	else if (mode->clock <= 74250)
> +		factor = 8 * 3;
> +	else if (mode->clock <= 167000)
> +		factor = 4 * 3;
> +	else
> +		factor = 2 * 3;
> +	pll_rate = pix_rate * factor;
> +
> +	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> +		pll_rate, pix_rate);
> +
> +	pll_rate = clk_get_rate(dpi->clk[MTK_DPI_CLK_TVD_PLL]);
> +	pix_rate = pll_rate / factor;
> +	clk_set_rate(dpi->clk[MTK_DPI_CLK_DPI_PIXEL], pix_rate);
> +	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> +		pll_rate, pix_rate);
> +
> +	return 0;
> +}
> +
> +static const struct mtk_dpi_conf mt8173_conf = {
> +	.clk_config = mt8173_clk_config,
> +};
> +
> +static const struct of_device_id mtk_dpi_of_ids[] = {
> +	{ .compatible = "mediatek,mt8173-dpi",
> +		.data = &mt8173_conf,
> +	},
> +	{}
> +};
> +
>  static int mtk_dpi_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct mtk_dpi *dpi;
>  	struct resource *mem;
> +	struct device_node *np = dev->of_node;
>  	struct device_node *ep, *bridge_node = NULL;
>  	int comp_id;
> +	const struct of_device_id *match;
> +	struct mtk_dpi_conf *conf;
>  	int ret;
>  
> +	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
> +	if (!match)
> +		return -ENODEV;
> +
>  	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
>  	if (!dpi)
>  		return -ENOMEM;
>  
>  	dpi->dev = dev;
> +	dpi->data = (void *)match->data;
> +	conf = (struct mtk_dpi_conf *)match->data;
>  
>  	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>  	dpi->regs = devm_ioremap_resource(dev, mem);
> @@ -679,24 +742,9 @@ static int mtk_dpi_probe(struct platform_device *pdev)
>  		return ret;
>  	}
>  
> -	dpi->engine_clk = devm_clk_get(dev, "engine");
> -	if (IS_ERR(dpi->engine_clk)) {
> -		ret = PTR_ERR(dpi->engine_clk);
> -		dev_err(dev, "Failed to get engine clock: %d\n", ret);
> -		return ret;
> -	}
> -
> -	dpi->pixel_clk = devm_clk_get(dev, "pixel");
> -	if (IS_ERR(dpi->pixel_clk)) {
> -		ret = PTR_ERR(dpi->pixel_clk);
> -		dev_err(dev, "Failed to get pixel clock: %d\n", ret);
> -		return ret;
> -	}
> -
> -	dpi->tvd_clk = devm_clk_get(dev, "pll");
> -	if (IS_ERR(dpi->tvd_clk)) {
> -		ret = PTR_ERR(dpi->tvd_clk);
> -		dev_err(dev, "Failed to get tvdpll clock: %d\n", ret);
> +	ret = mtk_dpi_parse_clk_from_dt(dpi, np);
> +	if (ret) {
> +		dev_err(dev, "parse tvd div clk failed!");
>  		return ret;
>  	}
>  
> @@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
>  	return 0;
>  }
>  
> -static const struct of_device_id mtk_dpi_of_ids[] = {
> -	{ .compatible = "mediatek,mt8173-dpi", },
> -	{}
> -};
> -
>  struct platform_driver mtk_dpi_driver = {
>  	.probe = mtk_dpi_probe,
>  	.remove = mtk_dpi_remove,

Re: [PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Philipp Zabel]

Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> Pixel clock should be 297MHz when resolution is 4K.

This patch does two different things, please don't conflate them.

First, it adds support for 16*3 and 2*3 factors between PLL and pixel
clock. This should be a separate patch and does what this patch
description says.

The second part moves the clocks into an array and adds an indirection
to clock registration depending on of_match_node. This should be a
separate patch. I suppose this change is in preparation for mt2701
support, but I'm not sure yet if it is needed at all.

regards
Philipp

> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
>  1 file changed, 96 insertions(+), 53 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index d05ca79..fa390e0 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
>  	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
>  };
>  
> +enum mtk_dpi_clk_id {
> +	MTK_DPI_CLK_DPI_ENGINE,
> +	MTK_DPI_CLK_DPI_PIXEL,
> +	MTK_DPI_CLK_TVD_PLL,
> +	MTK_DPI_CLK_COUNT,
> +};
> +
> +static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
> +	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
> +	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
> +	[MTK_DPI_CLK_TVD_PLL] = "pll",
> +};
> +
>  struct mtk_dpi {
>  	struct mtk_ddp_comp ddp_comp;
>  	struct drm_encoder encoder;
>  	void __iomem *regs;
>  	struct device *dev;
> -	struct clk *engine_clk;
> -	struct clk *pixel_clk;
> -	struct clk *tvd_clk;
> +	struct clk *clk[MTK_DPI_CLK_COUNT];
>  	int irq;
>  	struct drm_display_mode mode;
>  	enum mtk_dpi_out_color_format color_format;
> @@ -76,6 +87,7 @@ struct mtk_dpi {
>  	enum mtk_dpi_out_channel_swap channel_swap;
>  	bool power_sta;
>  	u8 power_ctl;
> +	void *data;
>  };
>  
>  static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
> @@ -114,6 +126,10 @@ struct mtk_dpi_yc_limit {
>  	u16 c_bottom;
>  };
>  
> +struct mtk_dpi_conf {
> +	int (*clk_config)(struct mtk_dpi *dpi, struct drm_display_mode *mode);
> +};
> +
>  static void mtk_dpi_mask(struct mtk_dpi *dpi, u32 offset, u32 val, u32 mask)
>  {
>  	u32 tmp = readl(dpi->regs + offset) & ~mask;
> @@ -377,8 +393,8 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
>  		return;
>  
>  	mtk_dpi_disable(dpi);
> -	clk_disable_unprepare(dpi->pixel_clk);
> -	clk_disable_unprepare(dpi->engine_clk);
> +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
> +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
>  	dpi->power_sta = false;
>  }
>  
> @@ -395,13 +411,13 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
>  	if (dpi->power_sta)
>  		return 0;
>  
> -	ret = clk_prepare_enable(dpi->engine_clk);
> +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
>  	if (ret) {
>  		dev_err(dpi->dev, "Failed to enable engine clock: %d\n", ret);
>  		goto err_eng;
>  	}
>  
> -	ret = clk_prepare_enable(dpi->pixel_clk);
> +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
>  	if (ret) {
>  		dev_err(dpi->dev, "Failed to enable pixel clock: %d\n", ret);
>  		goto err_pixel;
> @@ -412,7 +428,7 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
>  	return 0;
>  
>  err_pixel:
> -	clk_disable_unprepare(dpi->engine_clk);
> +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
>  err_eng:
>  	dpi->power_ctl &= ~pctl;
>  	return ret;
> @@ -428,34 +444,18 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
>  	struct mtk_dpi_sync_param vsync_leven = { 0 };
>  	struct mtk_dpi_sync_param vsync_rodd = { 0 };
>  	struct mtk_dpi_sync_param vsync_reven = { 0 };
> -	unsigned long pix_rate;
> -	unsigned long pll_rate;
> -	unsigned int factor;
> +	struct mtk_dpi_conf *conf;
> +	int ret;
>  
>  	if (!dpi) {
>  		dev_err(dpi->dev, "invalid argument\n");
>  		return -EINVAL;
>  	}
>  
> -	pix_rate = 1000UL * mode->clock;
> -	if (mode->clock <= 74000)
> -		factor = 8 * 3;
> -	else
> -		factor = 4 * 3;
> -	pll_rate = pix_rate * factor;
> -
> -	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> -		pll_rate, pix_rate);
> -
> -	clk_set_rate(dpi->tvd_clk, pll_rate);
> -	pll_rate = clk_get_rate(dpi->tvd_clk);
> -
> -	pix_rate = pll_rate / factor;
> -	clk_set_rate(dpi->pixel_clk, pix_rate);
> -	pix_rate = clk_get_rate(dpi->pixel_clk);
> -
> -	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> -		pll_rate, pix_rate);
> +	conf = (struct mtk_dpi_conf *)dpi->data;
> +	ret = conf->clk_config(dpi, mode);
> +	if (ret)
> +		dev_err(dpi->dev, "dpi clk set fail\n");
>  
>  	limit.c_bottom = 0x0010;
>  	limit.c_top = 0x0FE0;
> @@ -656,20 +656,83 @@ static const struct component_ops mtk_dpi_component_ops = {
>  	.unbind = mtk_dpi_unbind,
>  };
>  
> +static int mtk_dpi_parse_clk_from_dt(struct mtk_dpi *dpi,
> +				     struct device_node *np)
> +{
> +	int i;
> +
> +	for (i = 0; i < ARRAY_SIZE(mtk_dpi_clk_names); i++) {
> +		dpi->clk[i] = of_clk_get_by_name(np,
> +						  mtk_dpi_clk_names[i]);
> +		if (IS_ERR(dpi->clk[i]))
> +			return PTR_ERR(dpi->clk[i]);
> +	}
> +	return 0;
> +}
> +
> +static int mt8173_clk_config(struct mtk_dpi *dpi, struct drm_display_mode *mode)
> +{
> +	unsigned long pix_rate;
> +	unsigned long pll_rate;
> +	unsigned int factor;
> +
> +	pix_rate = 1000UL * mode->clock;
> +	if (mode->clock <= 27000)
> +		factor = 16 * 3;
> +	else if (mode->clock <= 74250)
> +		factor = 8 * 3;
> +	else if (mode->clock <= 167000)
> +		factor = 4 * 3;
> +	else
> +		factor = 2 * 3;
> +	pll_rate = pix_rate * factor;
> +
> +	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> +		pll_rate, pix_rate);
> +
> +	pll_rate = clk_get_rate(dpi->clk[MTK_DPI_CLK_TVD_PLL]);
> +	pix_rate = pll_rate / factor;
> +	clk_set_rate(dpi->clk[MTK_DPI_CLK_DPI_PIXEL], pix_rate);
> +	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> +		pll_rate, pix_rate);
> +
> +	return 0;
> +}
> +
> +static const struct mtk_dpi_conf mt8173_conf = {
> +	.clk_config = mt8173_clk_config,
> +};
> +
> +static const struct of_device_id mtk_dpi_of_ids[] = {
> +	{ .compatible = "mediatek,mt8173-dpi",
> +		.data = &mt8173_conf,
> +	},
> +	{}
> +};
> +
>  static int mtk_dpi_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct mtk_dpi *dpi;
>  	struct resource *mem;
> +	struct device_node *np = dev->of_node;
>  	struct device_node *ep, *bridge_node = NULL;
>  	int comp_id;
> +	const struct of_device_id *match;
> +	struct mtk_dpi_conf *conf;
>  	int ret;
>  
> +	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
> +	if (!match)
> +		return -ENODEV;
> +
>  	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
>  	if (!dpi)
>  		return -ENOMEM;
>  
>  	dpi->dev = dev;
> +	dpi->data = (void *)match->data;
> +	conf = (struct mtk_dpi_conf *)match->data;
>  
>  	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>  	dpi->regs = devm_ioremap_resource(dev, mem);
> @@ -679,24 +742,9 @@ static int mtk_dpi_probe(struct platform_device *pdev)
>  		return ret;
>  	}
>  
> -	dpi->engine_clk = devm_clk_get(dev, "engine");
> -	if (IS_ERR(dpi->engine_clk)) {
> -		ret = PTR_ERR(dpi->engine_clk);
> -		dev_err(dev, "Failed to get engine clock: %d\n", ret);
> -		return ret;
> -	}
> -
> -	dpi->pixel_clk = devm_clk_get(dev, "pixel");
> -	if (IS_ERR(dpi->pixel_clk)) {
> -		ret = PTR_ERR(dpi->pixel_clk);
> -		dev_err(dev, "Failed to get pixel clock: %d\n", ret);
> -		return ret;
> -	}
> -
> -	dpi->tvd_clk = devm_clk_get(dev, "pll");
> -	if (IS_ERR(dpi->tvd_clk)) {
> -		ret = PTR_ERR(dpi->tvd_clk);
> -		dev_err(dev, "Failed to get tvdpll clock: %d\n", ret);
> +	ret = mtk_dpi_parse_clk_from_dt(dpi, np);
> +	if (ret) {
> +		dev_err(dev, "parse tvd div clk failed!");
>  		return ret;
>  	}
>  
> @@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
>  	return 0;
>  }
>  
> -static const struct of_device_id mtk_dpi_of_ids[] = {
> -	{ .compatible = "mediatek,mt8173-dpi", },
> -	{}
> -};
> -
>  struct platform_driver mtk_dpi_driver = {
>  	.probe = mtk_dpi_probe,
>  	.remove = mtk_dpi_remove,


_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Philipp Zabel]

Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> Pixel clock should be 297MHz when resolution is 4K.

This patch does two different things, please don't conflate them.

First, it adds support for 16*3 and 2*3 factors between PLL and pixel
clock. This should be a separate patch and does what this patch
description says.

The second part moves the clocks into an array and adds an indirection
to clock registration depending on of_match_node. This should be a
separate patch. I suppose this change is in preparation for mt2701
support, but I'm not sure yet if it is needed at all.

regards
Philipp

> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
>  1 file changed, 96 insertions(+), 53 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index d05ca79..fa390e0 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
>  	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
>  };
>  
> +enum mtk_dpi_clk_id {
> +	MTK_DPI_CLK_DPI_ENGINE,
> +	MTK_DPI_CLK_DPI_PIXEL,
> +	MTK_DPI_CLK_TVD_PLL,
> +	MTK_DPI_CLK_COUNT,
> +};
> +
> +static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
> +	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
> +	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
> +	[MTK_DPI_CLK_TVD_PLL] = "pll",
> +};
> +
>  struct mtk_dpi {
>  	struct mtk_ddp_comp ddp_comp;
>  	struct drm_encoder encoder;
>  	void __iomem *regs;
>  	struct device *dev;
> -	struct clk *engine_clk;
> -	struct clk *pixel_clk;
> -	struct clk *tvd_clk;
> +	struct clk *clk[MTK_DPI_CLK_COUNT];
>  	int irq;
>  	struct drm_display_mode mode;
>  	enum mtk_dpi_out_color_format color_format;
> @@ -76,6 +87,7 @@ struct mtk_dpi {
>  	enum mtk_dpi_out_channel_swap channel_swap;
>  	bool power_sta;
>  	u8 power_ctl;
> +	void *data;
>  };
>  
>  static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
> @@ -114,6 +126,10 @@ struct mtk_dpi_yc_limit {
>  	u16 c_bottom;
>  };
>  
> +struct mtk_dpi_conf {
> +	int (*clk_config)(struct mtk_dpi *dpi, struct drm_display_mode *mode);
> +};
> +
>  static void mtk_dpi_mask(struct mtk_dpi *dpi, u32 offset, u32 val, u32 mask)
>  {
>  	u32 tmp = readl(dpi->regs + offset) & ~mask;
> @@ -377,8 +393,8 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
>  		return;
>  
>  	mtk_dpi_disable(dpi);
> -	clk_disable_unprepare(dpi->pixel_clk);
> -	clk_disable_unprepare(dpi->engine_clk);
> +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
> +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
>  	dpi->power_sta = false;
>  }
>  
> @@ -395,13 +411,13 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
>  	if (dpi->power_sta)
>  		return 0;
>  
> -	ret = clk_prepare_enable(dpi->engine_clk);
> +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
>  	if (ret) {
>  		dev_err(dpi->dev, "Failed to enable engine clock: %d\n", ret);
>  		goto err_eng;
>  	}
>  
> -	ret = clk_prepare_enable(dpi->pixel_clk);
> +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
>  	if (ret) {
>  		dev_err(dpi->dev, "Failed to enable pixel clock: %d\n", ret);
>  		goto err_pixel;
> @@ -412,7 +428,7 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
>  	return 0;
>  
>  err_pixel:
> -	clk_disable_unprepare(dpi->engine_clk);
> +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
>  err_eng:
>  	dpi->power_ctl &= ~pctl;
>  	return ret;
> @@ -428,34 +444,18 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
>  	struct mtk_dpi_sync_param vsync_leven = { 0 };
>  	struct mtk_dpi_sync_param vsync_rodd = { 0 };
>  	struct mtk_dpi_sync_param vsync_reven = { 0 };
> -	unsigned long pix_rate;
> -	unsigned long pll_rate;
> -	unsigned int factor;
> +	struct mtk_dpi_conf *conf;
> +	int ret;
>  
>  	if (!dpi) {
>  		dev_err(dpi->dev, "invalid argument\n");
>  		return -EINVAL;
>  	}
>  
> -	pix_rate = 1000UL * mode->clock;
> -	if (mode->clock <= 74000)
> -		factor = 8 * 3;
> -	else
> -		factor = 4 * 3;
> -	pll_rate = pix_rate * factor;
> -
> -	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> -		pll_rate, pix_rate);
> -
> -	clk_set_rate(dpi->tvd_clk, pll_rate);
> -	pll_rate = clk_get_rate(dpi->tvd_clk);
> -
> -	pix_rate = pll_rate / factor;
> -	clk_set_rate(dpi->pixel_clk, pix_rate);
> -	pix_rate = clk_get_rate(dpi->pixel_clk);
> -
> -	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> -		pll_rate, pix_rate);
> +	conf = (struct mtk_dpi_conf *)dpi->data;
> +	ret = conf->clk_config(dpi, mode);
> +	if (ret)
> +		dev_err(dpi->dev, "dpi clk set fail\n");
>  
>  	limit.c_bottom = 0x0010;
>  	limit.c_top = 0x0FE0;
> @@ -656,20 +656,83 @@ static const struct component_ops mtk_dpi_component_ops = {
>  	.unbind = mtk_dpi_unbind,
>  };
>  
> +static int mtk_dpi_parse_clk_from_dt(struct mtk_dpi *dpi,
> +				     struct device_node *np)
> +{
> +	int i;
> +
> +	for (i = 0; i < ARRAY_SIZE(mtk_dpi_clk_names); i++) {
> +		dpi->clk[i] = of_clk_get_by_name(np,
> +						  mtk_dpi_clk_names[i]);
> +		if (IS_ERR(dpi->clk[i]))
> +			return PTR_ERR(dpi->clk[i]);
> +	}
> +	return 0;
> +}
> +
> +static int mt8173_clk_config(struct mtk_dpi *dpi, struct drm_display_mode *mode)
> +{
> +	unsigned long pix_rate;
> +	unsigned long pll_rate;
> +	unsigned int factor;
> +
> +	pix_rate = 1000UL * mode->clock;
> +	if (mode->clock <= 27000)
> +		factor = 16 * 3;
> +	else if (mode->clock <= 74250)
> +		factor = 8 * 3;
> +	else if (mode->clock <= 167000)
> +		factor = 4 * 3;
> +	else
> +		factor = 2 * 3;
> +	pll_rate = pix_rate * factor;
> +
> +	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> +		pll_rate, pix_rate);
> +
> +	pll_rate = clk_get_rate(dpi->clk[MTK_DPI_CLK_TVD_PLL]);
> +	pix_rate = pll_rate / factor;
> +	clk_set_rate(dpi->clk[MTK_DPI_CLK_DPI_PIXEL], pix_rate);
> +	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> +		pll_rate, pix_rate);
> +
> +	return 0;
> +}
> +
> +static const struct mtk_dpi_conf mt8173_conf = {
> +	.clk_config = mt8173_clk_config,
> +};
> +
> +static const struct of_device_id mtk_dpi_of_ids[] = {
> +	{ .compatible = "mediatek,mt8173-dpi",
> +		.data = &mt8173_conf,
> +	},
> +	{}
> +};
> +
>  static int mtk_dpi_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct mtk_dpi *dpi;
>  	struct resource *mem;
> +	struct device_node *np = dev->of_node;
>  	struct device_node *ep, *bridge_node = NULL;
>  	int comp_id;
> +	const struct of_device_id *match;
> +	struct mtk_dpi_conf *conf;
>  	int ret;
>  
> +	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
> +	if (!match)
> +		return -ENODEV;
> +
>  	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
>  	if (!dpi)
>  		return -ENOMEM;
>  
>  	dpi->dev = dev;
> +	dpi->data = (void *)match->data;
> +	conf = (struct mtk_dpi_conf *)match->data;
>  
>  	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>  	dpi->regs = devm_ioremap_resource(dev, mem);
> @@ -679,24 +742,9 @@ static int mtk_dpi_probe(struct platform_device *pdev)
>  		return ret;
>  	}
>  
> -	dpi->engine_clk = devm_clk_get(dev, "engine");
> -	if (IS_ERR(dpi->engine_clk)) {
> -		ret = PTR_ERR(dpi->engine_clk);
> -		dev_err(dev, "Failed to get engine clock: %d\n", ret);
> -		return ret;
> -	}
> -
> -	dpi->pixel_clk = devm_clk_get(dev, "pixel");
> -	if (IS_ERR(dpi->pixel_clk)) {
> -		ret = PTR_ERR(dpi->pixel_clk);
> -		dev_err(dev, "Failed to get pixel clock: %d\n", ret);
> -		return ret;
> -	}
> -
> -	dpi->tvd_clk = devm_clk_get(dev, "pll");
> -	if (IS_ERR(dpi->tvd_clk)) {
> -		ret = PTR_ERR(dpi->tvd_clk);
> -		dev_err(dev, "Failed to get tvdpll clock: %d\n", ret);
> +	ret = mtk_dpi_parse_clk_from_dt(dpi, np);
> +	if (ret) {
> +		dev_err(dev, "parse tvd div clk failed!");
>  		return ret;
>  	}
>  
> @@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
>  	return 0;
>  }
>  
> -static const struct of_device_id mtk_dpi_of_ids[] = {
> -	{ .compatible = "mediatek,mt8173-dpi", },
> -	{}
> -};
> -
>  struct platform_driver mtk_dpi_driver = {
>  	.probe = mtk_dpi_probe,
>  	.remove = mtk_dpi_remove,

Re: [PATCH v2 2/3] drm/mediatek: enhance the HDMI driving current

[Philipp Zabel]

Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> In order to improve 4K resolution performance,
> we have to enhance the HDMI driving currend
                                           ^
Typo, s/currend/current/

Besides that, this patch looks good to me.

regards
Philipp

> when clock rate is greater than 165MHz.
> 
> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++++++++++++++-------
>  1 file changed, 30 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> index 8a24754..51cb9cf 100644
> --- a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> +++ b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> @@ -265,6 +265,9 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>  	struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
>  	unsigned int pre_div;
>  	unsigned int div;
> +	unsigned int pre_ibias;
> +	unsigned int hdmi_ibias;
> +	unsigned int imp_en;
>  
>  	dev_dbg(hdmi_phy->dev, "%s: %lu Hz, parent: %lu Hz\n", __func__,
>  		rate, parent_rate);
> @@ -298,18 +301,31 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>  			  (0x1 << PLL_BR_SHIFT),
>  			  RG_HDMITX_PLL_BP | RG_HDMITX_PLL_BC |
>  			  RG_HDMITX_PLL_BR);
> -	mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3, RG_HDMITX_PRD_IMP_EN);
> +	if (rate < 165000000) {
> +		mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3,
> +					RG_HDMITX_PRD_IMP_EN);
> +		pre_ibias = 0x3;
> +		imp_en = 0x0;
> +		hdmi_ibias = hdmi_phy->ibias;
> +	} else {
> +		mtk_hdmi_phy_set_bits(hdmi_phy, HDMI_CON3,
> +				      RG_HDMITX_PRD_IMP_EN);
> +		pre_ibias = 0x6;
> +		imp_en = 0xf;
> +		hdmi_ibias = hdmi_phy->ibias_up;
> +	}
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON4,
> -			  (0x3 << PRD_IBIAS_CLK_SHIFT) |
> -			  (0x3 << PRD_IBIAS_D2_SHIFT) |
> -			  (0x3 << PRD_IBIAS_D1_SHIFT) |
> -			  (0x3 << PRD_IBIAS_D0_SHIFT),
> +			  (pre_ibias << PRD_IBIAS_CLK_SHIFT) |
> +			  (pre_ibias << PRD_IBIAS_D2_SHIFT) |
> +			  (pre_ibias << PRD_IBIAS_D1_SHIFT) |
> +			  (pre_ibias << PRD_IBIAS_D0_SHIFT),
>  			  RG_HDMITX_PRD_IBIAS_CLK |
>  			  RG_HDMITX_PRD_IBIAS_D2 |
>  			  RG_HDMITX_PRD_IBIAS_D1 |
>  			  RG_HDMITX_PRD_IBIAS_D0);
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON3,
> -			  (0x0 << DRV_IMP_EN_SHIFT), RG_HDMITX_DRV_IMP_EN);
> +			  (imp_en << DRV_IMP_EN_SHIFT),
> +			  RG_HDMITX_DRV_IMP_EN);
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON6,
>  			  (hdmi_phy->drv_imp_clk << DRV_IMP_CLK_SHIFT) |
>  			  (hdmi_phy->drv_imp_d2 << DRV_IMP_D2_SHIFT) |
> @@ -318,12 +334,14 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>  			  RG_HDMITX_DRV_IMP_CLK | RG_HDMITX_DRV_IMP_D2 |
>  			  RG_HDMITX_DRV_IMP_D1 | RG_HDMITX_DRV_IMP_D0);
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON5,
> -			  (hdmi_phy->ibias << DRV_IBIAS_CLK_SHIFT) |
> -			  (hdmi_phy->ibias << DRV_IBIAS_D2_SHIFT) |
> -			  (hdmi_phy->ibias << DRV_IBIAS_D1_SHIFT) |
> -			  (hdmi_phy->ibias << DRV_IBIAS_D0_SHIFT),
> -			  RG_HDMITX_DRV_IBIAS_CLK | RG_HDMITX_DRV_IBIAS_D2 |
> -			  RG_HDMITX_DRV_IBIAS_D1 | RG_HDMITX_DRV_IBIAS_D0);
> +			  (hdmi_ibias << DRV_IBIAS_CLK_SHIFT) |
> +			  (hdmi_ibias << DRV_IBIAS_D2_SHIFT) |
> +			  (hdmi_ibias << DRV_IBIAS_D1_SHIFT) |
> +			  (hdmi_ibias << DRV_IBIAS_D0_SHIFT),
> +			  RG_HDMITX_DRV_IBIAS_CLK |
> +			  RG_HDMITX_DRV_IBIAS_D2 |
> +			  RG_HDMITX_DRV_IBIAS_D1 |
> +			  RG_HDMITX_DRV_IBIAS_D0);
>  	return 0;
>  }
>  

Re: [PATCH v2 2/3] drm/mediatek: enhance the HDMI driving current

[Philipp Zabel]

Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> In order to improve 4K resolution performance,
> we have to enhance the HDMI driving currend
                                           ^
Typo, s/currend/current/

Besides that, this patch looks good to me.

regards
Philipp

> when clock rate is greater than 165MHz.
> 
> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++++++++++++++-------
>  1 file changed, 30 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> index 8a24754..51cb9cf 100644
> --- a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> +++ b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> @@ -265,6 +265,9 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>  	struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
>  	unsigned int pre_div;
>  	unsigned int div;
> +	unsigned int pre_ibias;
> +	unsigned int hdmi_ibias;
> +	unsigned int imp_en;
>  
>  	dev_dbg(hdmi_phy->dev, "%s: %lu Hz, parent: %lu Hz\n", __func__,
>  		rate, parent_rate);
> @@ -298,18 +301,31 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>  			  (0x1 << PLL_BR_SHIFT),
>  			  RG_HDMITX_PLL_BP | RG_HDMITX_PLL_BC |
>  			  RG_HDMITX_PLL_BR);
> -	mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3, RG_HDMITX_PRD_IMP_EN);
> +	if (rate < 165000000) {
> +		mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3,
> +					RG_HDMITX_PRD_IMP_EN);
> +		pre_ibias = 0x3;
> +		imp_en = 0x0;
> +		hdmi_ibias = hdmi_phy->ibias;
> +	} else {
> +		mtk_hdmi_phy_set_bits(hdmi_phy, HDMI_CON3,
> +				      RG_HDMITX_PRD_IMP_EN);
> +		pre_ibias = 0x6;
> +		imp_en = 0xf;
> +		hdmi_ibias = hdmi_phy->ibias_up;
> +	}
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON4,
> -			  (0x3 << PRD_IBIAS_CLK_SHIFT) |
> -			  (0x3 << PRD_IBIAS_D2_SHIFT) |
> -			  (0x3 << PRD_IBIAS_D1_SHIFT) |
> -			  (0x3 << PRD_IBIAS_D0_SHIFT),
> +			  (pre_ibias << PRD_IBIAS_CLK_SHIFT) |
> +			  (pre_ibias << PRD_IBIAS_D2_SHIFT) |
> +			  (pre_ibias << PRD_IBIAS_D1_SHIFT) |
> +			  (pre_ibias << PRD_IBIAS_D0_SHIFT),
>  			  RG_HDMITX_PRD_IBIAS_CLK |
>  			  RG_HDMITX_PRD_IBIAS_D2 |
>  			  RG_HDMITX_PRD_IBIAS_D1 |
>  			  RG_HDMITX_PRD_IBIAS_D0);
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON3,
> -			  (0x0 << DRV_IMP_EN_SHIFT), RG_HDMITX_DRV_IMP_EN);
> +			  (imp_en << DRV_IMP_EN_SHIFT),
> +			  RG_HDMITX_DRV_IMP_EN);
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON6,
>  			  (hdmi_phy->drv_imp_clk << DRV_IMP_CLK_SHIFT) |
>  			  (hdmi_phy->drv_imp_d2 << DRV_IMP_D2_SHIFT) |
> @@ -318,12 +334,14 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>  			  RG_HDMITX_DRV_IMP_CLK | RG_HDMITX_DRV_IMP_D2 |
>  			  RG_HDMITX_DRV_IMP_D1 | RG_HDMITX_DRV_IMP_D0);
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON5,
> -			  (hdmi_phy->ibias << DRV_IBIAS_CLK_SHIFT) |
> -			  (hdmi_phy->ibias << DRV_IBIAS_D2_SHIFT) |
> -			  (hdmi_phy->ibias << DRV_IBIAS_D1_SHIFT) |
> -			  (hdmi_phy->ibias << DRV_IBIAS_D0_SHIFT),
> -			  RG_HDMITX_DRV_IBIAS_CLK | RG_HDMITX_DRV_IBIAS_D2 |
> -			  RG_HDMITX_DRV_IBIAS_D1 | RG_HDMITX_DRV_IBIAS_D0);
> +			  (hdmi_ibias << DRV_IBIAS_CLK_SHIFT) |
> +			  (hdmi_ibias << DRV_IBIAS_D2_SHIFT) |
> +			  (hdmi_ibias << DRV_IBIAS_D1_SHIFT) |
> +			  (hdmi_ibias << DRV_IBIAS_D0_SHIFT),
> +			  RG_HDMITX_DRV_IBIAS_CLK |
> +			  RG_HDMITX_DRV_IBIAS_D2 |
> +			  RG_HDMITX_DRV_IBIAS_D1 |
> +			  RG_HDMITX_DRV_IBIAS_D0);
>  	return 0;
>  }
>  


_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 2/3] drm/mediatek: enhance the HDMI driving current

[Philipp Zabel]

Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> In order to improve 4K resolution performance,
> we have to enhance the HDMI driving currend
                                           ^
Typo, s/currend/current/

Besides that, this patch looks good to me.

regards
Philipp

> when clock rate is greater than 165MHz.
> 
> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++++++++++++++-------
>  1 file changed, 30 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> index 8a24754..51cb9cf 100644
> --- a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> +++ b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> @@ -265,6 +265,9 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>  	struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
>  	unsigned int pre_div;
>  	unsigned int div;
> +	unsigned int pre_ibias;
> +	unsigned int hdmi_ibias;
> +	unsigned int imp_en;
>  
>  	dev_dbg(hdmi_phy->dev, "%s: %lu Hz, parent: %lu Hz\n", __func__,
>  		rate, parent_rate);
> @@ -298,18 +301,31 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>  			  (0x1 << PLL_BR_SHIFT),
>  			  RG_HDMITX_PLL_BP | RG_HDMITX_PLL_BC |
>  			  RG_HDMITX_PLL_BR);
> -	mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3, RG_HDMITX_PRD_IMP_EN);
> +	if (rate < 165000000) {
> +		mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3,
> +					RG_HDMITX_PRD_IMP_EN);
> +		pre_ibias = 0x3;
> +		imp_en = 0x0;
> +		hdmi_ibias = hdmi_phy->ibias;
> +	} else {
> +		mtk_hdmi_phy_set_bits(hdmi_phy, HDMI_CON3,
> +				      RG_HDMITX_PRD_IMP_EN);
> +		pre_ibias = 0x6;
> +		imp_en = 0xf;
> +		hdmi_ibias = hdmi_phy->ibias_up;
> +	}
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON4,
> -			  (0x3 << PRD_IBIAS_CLK_SHIFT) |
> -			  (0x3 << PRD_IBIAS_D2_SHIFT) |
> -			  (0x3 << PRD_IBIAS_D1_SHIFT) |
> -			  (0x3 << PRD_IBIAS_D0_SHIFT),
> +			  (pre_ibias << PRD_IBIAS_CLK_SHIFT) |
> +			  (pre_ibias << PRD_IBIAS_D2_SHIFT) |
> +			  (pre_ibias << PRD_IBIAS_D1_SHIFT) |
> +			  (pre_ibias << PRD_IBIAS_D0_SHIFT),
>  			  RG_HDMITX_PRD_IBIAS_CLK |
>  			  RG_HDMITX_PRD_IBIAS_D2 |
>  			  RG_HDMITX_PRD_IBIAS_D1 |
>  			  RG_HDMITX_PRD_IBIAS_D0);
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON3,
> -			  (0x0 << DRV_IMP_EN_SHIFT), RG_HDMITX_DRV_IMP_EN);
> +			  (imp_en << DRV_IMP_EN_SHIFT),
> +			  RG_HDMITX_DRV_IMP_EN);
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON6,
>  			  (hdmi_phy->drv_imp_clk << DRV_IMP_CLK_SHIFT) |
>  			  (hdmi_phy->drv_imp_d2 << DRV_IMP_D2_SHIFT) |
> @@ -318,12 +334,14 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>  			  RG_HDMITX_DRV_IMP_CLK | RG_HDMITX_DRV_IMP_D2 |
>  			  RG_HDMITX_DRV_IMP_D1 | RG_HDMITX_DRV_IMP_D0);
>  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON5,
> -			  (hdmi_phy->ibias << DRV_IBIAS_CLK_SHIFT) |
> -			  (hdmi_phy->ibias << DRV_IBIAS_D2_SHIFT) |
> -			  (hdmi_phy->ibias << DRV_IBIAS_D1_SHIFT) |
> -			  (hdmi_phy->ibias << DRV_IBIAS_D0_SHIFT),
> -			  RG_HDMITX_DRV_IBIAS_CLK | RG_HDMITX_DRV_IBIAS_D2 |
> -			  RG_HDMITX_DRV_IBIAS_D1 | RG_HDMITX_DRV_IBIAS_D0);
> +			  (hdmi_ibias << DRV_IBIAS_CLK_SHIFT) |
> +			  (hdmi_ibias << DRV_IBIAS_D2_SHIFT) |
> +			  (hdmi_ibias << DRV_IBIAS_D1_SHIFT) |
> +			  (hdmi_ibias << DRV_IBIAS_D0_SHIFT),
> +			  RG_HDMITX_DRV_IBIAS_CLK |
> +			  RG_HDMITX_DRV_IBIAS_D2 |
> +			  RG_HDMITX_DRV_IBIAS_D1 |
> +			  RG_HDMITX_DRV_IBIAS_D0);
>  	return 0;
>  }
>  

Re: [PATCH v2 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[Philipp Zabel]

Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> The mtk_hdmi_send_infoframe have to
> be run after PLL and PIXEL clock of HDMI enable.
> Make sure that HDMI inforframes can be sent
> successfully.
> 
> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_hdmi.c |   19 ++++++++++++-------
>  1 file changed, 12 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> index ba812ef..d8609f5 100644
> --- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> @@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
>  	phy_power_on(hdmi->phy);
>  	mtk_hdmi_aud_output_config(hdmi, mode);
>  
> -	mtk_hdmi_setup_audio_infoframe(hdmi);
> -	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> -	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> -	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> -		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> -
>  	mtk_hdmi_hw_vid_black(hdmi, false);
>  	mtk_hdmi_hw_aud_unmute(hdmi);
>  	mtk_hdmi_hw_send_av_unmute(hdmi);
> @@ -1401,14 +1395,25 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
>  	hdmi->powered = true;
>  }
>  
> +static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
> +				    struct drm_display_mode *mode)
> +{
> +	mtk_hdmi_setup_audio_infoframe(hdmi);
> +	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> +	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> +	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> +		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> +}
> +
>  static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
>  {
>  	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
>  
> +	phy_power_on(hdmi->phy);
>  	mtk_hdmi_output_set_display_mode(hdmi, &hdmi->mode);
>  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
>  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
> -	phy_power_on(hdmi->phy);

This change is not described in the patch description. Why is the phy
power on moved after the pixel clock enable?

> +	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
>  
>  	hdmi->enabled = true;
>  }

regards
Philipp

Re: [PATCH v2 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[Philipp Zabel]

Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> The mtk_hdmi_send_infoframe have to
> be run after PLL and PIXEL clock of HDMI enable.
> Make sure that HDMI inforframes can be sent
> successfully.
> 
> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_hdmi.c |   19 ++++++++++++-------
>  1 file changed, 12 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> index ba812ef..d8609f5 100644
> --- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> @@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
>  	phy_power_on(hdmi->phy);
>  	mtk_hdmi_aud_output_config(hdmi, mode);
>  
> -	mtk_hdmi_setup_audio_infoframe(hdmi);
> -	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> -	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> -	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> -		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> -
>  	mtk_hdmi_hw_vid_black(hdmi, false);
>  	mtk_hdmi_hw_aud_unmute(hdmi);
>  	mtk_hdmi_hw_send_av_unmute(hdmi);
> @@ -1401,14 +1395,25 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
>  	hdmi->powered = true;
>  }
>  
> +static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
> +				    struct drm_display_mode *mode)
> +{
> +	mtk_hdmi_setup_audio_infoframe(hdmi);
> +	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> +	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> +	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> +		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> +}
> +
>  static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
>  {
>  	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
>  
> +	phy_power_on(hdmi->phy);
>  	mtk_hdmi_output_set_display_mode(hdmi, &hdmi->mode);
>  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
>  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
> -	phy_power_on(hdmi->phy);

This change is not described in the patch description. Why is the phy
power on moved after the pixel clock enable?

> +	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
>  
>  	hdmi->enabled = true;
>  }

regards
Philipp

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[Philipp Zabel]

Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> The mtk_hdmi_send_infoframe have to
> be run after PLL and PIXEL clock of HDMI enable.
> Make sure that HDMI inforframes can be sent
> successfully.
> 
> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_hdmi.c |   19 ++++++++++++-------
>  1 file changed, 12 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> index ba812ef..d8609f5 100644
> --- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> @@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
>  	phy_power_on(hdmi->phy);
>  	mtk_hdmi_aud_output_config(hdmi, mode);
>  
> -	mtk_hdmi_setup_audio_infoframe(hdmi);
> -	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> -	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> -	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> -		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> -
>  	mtk_hdmi_hw_vid_black(hdmi, false);
>  	mtk_hdmi_hw_aud_unmute(hdmi);
>  	mtk_hdmi_hw_send_av_unmute(hdmi);
> @@ -1401,14 +1395,25 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
>  	hdmi->powered = true;
>  }
>  
> +static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
> +				    struct drm_display_mode *mode)
> +{
> +	mtk_hdmi_setup_audio_infoframe(hdmi);
> +	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> +	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> +	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> +		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> +}
> +
>  static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
>  {
>  	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
>  
> +	phy_power_on(hdmi->phy);
>  	mtk_hdmi_output_set_display_mode(hdmi, &hdmi->mode);
>  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
>  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
> -	phy_power_on(hdmi->phy);

This change is not described in the patch description. Why is the phy
power on moved after the pixel clock enable?

> +	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
>  
>  	hdmi->enabled = true;
>  }

regards
Philipp

Re: [PATCH v2 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[Bibby Hsieh]

Hi, Philipp,

Thanks for your review.

On Wed, 2016-07-27 at 11:27 +0200, Philipp Zabel wrote:
> Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> > From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > 
> > The mtk_hdmi_send_infoframe have to
> > be run after PLL and PIXEL clock of HDMI enable.
> > Make sure that HDMI inforframes can be sent
> > successfully.
> > 
> > Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_hdmi.c |   19 ++++++++++++-------
> >  1 file changed, 12 insertions(+), 7 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > index ba812ef..d8609f5 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > @@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
> >  	phy_power_on(hdmi->phy);
> >  	mtk_hdmi_aud_output_config(hdmi, mode);
> >  
> > -	mtk_hdmi_setup_audio_infoframe(hdmi);
> > -	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> > -	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> > -	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> > -		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> > -
> >  	mtk_hdmi_hw_vid_black(hdmi, false);
> >  	mtk_hdmi_hw_aud_unmute(hdmi);
> >  	mtk_hdmi_hw_send_av_unmute(hdmi);
> > @@ -1401,14 +1395,25 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
> >  	hdmi->powered = true;
> >  }
> >  
> > +static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
> > +				    struct drm_display_mode *mode)
> > +{
> > +	mtk_hdmi_setup_audio_infoframe(hdmi);
> > +	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> > +	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> > +	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> > +		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> > +}
> > +
> >  static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
> >  {
> >  	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
> >  
> > +	phy_power_on(hdmi->phy);
> >  	mtk_hdmi_output_set_display_mode(hdmi, &hdmi->mode);
> >  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
> >  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
> > -	phy_power_on(hdmi->phy);
> 
> This change is not described in the patch description. Why is the phy
> power on moved after the pixel clock enable?
> 
Ok, will rollback it.
> > +	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
> >  
> >  	hdmi->enabled = true;
> >  }
> 
> regards
> Philipp
> 

-- 
Bibby

Re: [PATCH v2 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[Bibby Hsieh]

Hi, Philipp,

Thanks for your review.

On Wed, 2016-07-27 at 11:27 +0200, Philipp Zabel wrote:
> Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> > From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > 
> > The mtk_hdmi_send_infoframe have to
> > be run after PLL and PIXEL clock of HDMI enable.
> > Make sure that HDMI inforframes can be sent
> > successfully.
> > 
> > Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_hdmi.c |   19 ++++++++++++-------
> >  1 file changed, 12 insertions(+), 7 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > index ba812ef..d8609f5 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > @@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
> >  	phy_power_on(hdmi->phy);
> >  	mtk_hdmi_aud_output_config(hdmi, mode);
> >  
> > -	mtk_hdmi_setup_audio_infoframe(hdmi);
> > -	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> > -	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> > -	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> > -		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> > -
> >  	mtk_hdmi_hw_vid_black(hdmi, false);
> >  	mtk_hdmi_hw_aud_unmute(hdmi);
> >  	mtk_hdmi_hw_send_av_unmute(hdmi);
> > @@ -1401,14 +1395,25 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
> >  	hdmi->powered = true;
> >  }
> >  
> > +static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
> > +				    struct drm_display_mode *mode)
> > +{
> > +	mtk_hdmi_setup_audio_infoframe(hdmi);
> > +	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> > +	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> > +	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> > +		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> > +}
> > +
> >  static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
> >  {
> >  	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
> >  
> > +	phy_power_on(hdmi->phy);
> >  	mtk_hdmi_output_set_display_mode(hdmi, &hdmi->mode);
> >  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
> >  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
> > -	phy_power_on(hdmi->phy);
> 
> This change is not described in the patch description. Why is the phy
> power on moved after the pixel clock enable?
> 
Ok, will rollback it.
> > +	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
> >  
> >  	hdmi->enabled = true;
> >  }
> 
> regards
> Philipp
> 

-- 
Bibby

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[Bibby Hsieh]

Hi, Philipp,

Thanks for your review.

On Wed, 2016-07-27 at 11:27 +0200, Philipp Zabel wrote:
> Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> > From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > 
> > The mtk_hdmi_send_infoframe have to
> > be run after PLL and PIXEL clock of HDMI enable.
> > Make sure that HDMI inforframes can be sent
> > successfully.
> > 
> > Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_hdmi.c |   19 ++++++++++++-------
> >  1 file changed, 12 insertions(+), 7 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > index ba812ef..d8609f5 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > @@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
> >  	phy_power_on(hdmi->phy);
> >  	mtk_hdmi_aud_output_config(hdmi, mode);
> >  
> > -	mtk_hdmi_setup_audio_infoframe(hdmi);
> > -	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> > -	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> > -	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> > -		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> > -
> >  	mtk_hdmi_hw_vid_black(hdmi, false);
> >  	mtk_hdmi_hw_aud_unmute(hdmi);
> >  	mtk_hdmi_hw_send_av_unmute(hdmi);
> > @@ -1401,14 +1395,25 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
> >  	hdmi->powered = true;
> >  }
> >  
> > +static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
> > +				    struct drm_display_mode *mode)
> > +{
> > +	mtk_hdmi_setup_audio_infoframe(hdmi);
> > +	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> > +	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> > +	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> > +		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> > +}
> > +
> >  static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
> >  {
> >  	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
> >  
> > +	phy_power_on(hdmi->phy);
> >  	mtk_hdmi_output_set_display_mode(hdmi, &hdmi->mode);
> >  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
> >  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
> > -	phy_power_on(hdmi->phy);
> 
> This change is not described in the patch description. Why is the phy
> power on moved after the pixel clock enable?
> 
Ok, will rollback it.
> > +	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
> >  
> >  	hdmi->enabled = true;
> >  }
> 
> regards
> Philipp
> 

-- 
Bibby

Re: [PATCH v2 2/3] drm/mediatek: enhance the HDMI driving current

[Bibby Hsieh]

Hi, Philipp,

Thanks for your review.

On Wed, 2016-07-27 at 11:25 +0200, Philipp Zabel wrote:
> Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> > From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > 
> > In order to improve 4K resolution performance,
> > we have to enhance the HDMI driving currend
>                                            ^
> Typo, s/currend/current/
> 
> Besides that, this patch looks good to me.
> 
Ok, I will fix that, thanks.
> regards
> Philipp
> 
> > when clock rate is greater than 165MHz.
> > 
> > Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++++++++++++++-------
> >  1 file changed, 30 insertions(+), 12 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> > index 8a24754..51cb9cf 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> > @@ -265,6 +265,9 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> >  	struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
> >  	unsigned int pre_div;
> >  	unsigned int div;
> > +	unsigned int pre_ibias;
> > +	unsigned int hdmi_ibias;
> > +	unsigned int imp_en;
> >  
> >  	dev_dbg(hdmi_phy->dev, "%s: %lu Hz, parent: %lu Hz\n", __func__,
> >  		rate, parent_rate);
> > @@ -298,18 +301,31 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> >  			  (0x1 << PLL_BR_SHIFT),
> >  			  RG_HDMITX_PLL_BP | RG_HDMITX_PLL_BC |
> >  			  RG_HDMITX_PLL_BR);
> > -	mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3, RG_HDMITX_PRD_IMP_EN);
> > +	if (rate < 165000000) {
> > +		mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3,
> > +					RG_HDMITX_PRD_IMP_EN);
> > +		pre_ibias = 0x3;
> > +		imp_en = 0x0;
> > +		hdmi_ibias = hdmi_phy->ibias;
> > +	} else {
> > +		mtk_hdmi_phy_set_bits(hdmi_phy, HDMI_CON3,
> > +				      RG_HDMITX_PRD_IMP_EN);
> > +		pre_ibias = 0x6;
> > +		imp_en = 0xf;
> > +		hdmi_ibias = hdmi_phy->ibias_up;
> > +	}
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON4,
> > -			  (0x3 << PRD_IBIAS_CLK_SHIFT) |
> > -			  (0x3 << PRD_IBIAS_D2_SHIFT) |
> > -			  (0x3 << PRD_IBIAS_D1_SHIFT) |
> > -			  (0x3 << PRD_IBIAS_D0_SHIFT),
> > +			  (pre_ibias << PRD_IBIAS_CLK_SHIFT) |
> > +			  (pre_ibias << PRD_IBIAS_D2_SHIFT) |
> > +			  (pre_ibias << PRD_IBIAS_D1_SHIFT) |
> > +			  (pre_ibias << PRD_IBIAS_D0_SHIFT),
> >  			  RG_HDMITX_PRD_IBIAS_CLK |
> >  			  RG_HDMITX_PRD_IBIAS_D2 |
> >  			  RG_HDMITX_PRD_IBIAS_D1 |
> >  			  RG_HDMITX_PRD_IBIAS_D0);
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON3,
> > -			  (0x0 << DRV_IMP_EN_SHIFT), RG_HDMITX_DRV_IMP_EN);
> > +			  (imp_en << DRV_IMP_EN_SHIFT),
> > +			  RG_HDMITX_DRV_IMP_EN);
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON6,
> >  			  (hdmi_phy->drv_imp_clk << DRV_IMP_CLK_SHIFT) |
> >  			  (hdmi_phy->drv_imp_d2 << DRV_IMP_D2_SHIFT) |
> > @@ -318,12 +334,14 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> >  			  RG_HDMITX_DRV_IMP_CLK | RG_HDMITX_DRV_IMP_D2 |
> >  			  RG_HDMITX_DRV_IMP_D1 | RG_HDMITX_DRV_IMP_D0);
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON5,
> > -			  (hdmi_phy->ibias << DRV_IBIAS_CLK_SHIFT) |
> > -			  (hdmi_phy->ibias << DRV_IBIAS_D2_SHIFT) |
> > -			  (hdmi_phy->ibias << DRV_IBIAS_D1_SHIFT) |
> > -			  (hdmi_phy->ibias << DRV_IBIAS_D0_SHIFT),
> > -			  RG_HDMITX_DRV_IBIAS_CLK | RG_HDMITX_DRV_IBIAS_D2 |
> > -			  RG_HDMITX_DRV_IBIAS_D1 | RG_HDMITX_DRV_IBIAS_D0);
> > +			  (hdmi_ibias << DRV_IBIAS_CLK_SHIFT) |
> > +			  (hdmi_ibias << DRV_IBIAS_D2_SHIFT) |
> > +			  (hdmi_ibias << DRV_IBIAS_D1_SHIFT) |
> > +			  (hdmi_ibias << DRV_IBIAS_D0_SHIFT),
> > +			  RG_HDMITX_DRV_IBIAS_CLK |
> > +			  RG_HDMITX_DRV_IBIAS_D2 |
> > +			  RG_HDMITX_DRV_IBIAS_D1 |
> > +			  RG_HDMITX_DRV_IBIAS_D0);
> >  	return 0;
> >  }
> >  
> 
> 

-- 
Bibby

Re: [PATCH v2 2/3] drm/mediatek: enhance the HDMI driving current

[Bibby Hsieh]

Hi, Philipp,

Thanks for your review.

On Wed, 2016-07-27 at 11:25 +0200, Philipp Zabel wrote:
> Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> > From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > 
> > In order to improve 4K resolution performance,
> > we have to enhance the HDMI driving currend
>                                            ^
> Typo, s/currend/current/
> 
> Besides that, this patch looks good to me.
> 
Ok, I will fix that, thanks.
> regards
> Philipp
> 
> > when clock rate is greater than 165MHz.
> > 
> > Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++++++++++++++-------
> >  1 file changed, 30 insertions(+), 12 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> > index 8a24754..51cb9cf 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> > @@ -265,6 +265,9 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> >  	struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
> >  	unsigned int pre_div;
> >  	unsigned int div;
> > +	unsigned int pre_ibias;
> > +	unsigned int hdmi_ibias;
> > +	unsigned int imp_en;
> >  
> >  	dev_dbg(hdmi_phy->dev, "%s: %lu Hz, parent: %lu Hz\n", __func__,
> >  		rate, parent_rate);
> > @@ -298,18 +301,31 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> >  			  (0x1 << PLL_BR_SHIFT),
> >  			  RG_HDMITX_PLL_BP | RG_HDMITX_PLL_BC |
> >  			  RG_HDMITX_PLL_BR);
> > -	mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3, RG_HDMITX_PRD_IMP_EN);
> > +	if (rate < 165000000) {
> > +		mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3,
> > +					RG_HDMITX_PRD_IMP_EN);
> > +		pre_ibias = 0x3;
> > +		imp_en = 0x0;
> > +		hdmi_ibias = hdmi_phy->ibias;
> > +	} else {
> > +		mtk_hdmi_phy_set_bits(hdmi_phy, HDMI_CON3,
> > +				      RG_HDMITX_PRD_IMP_EN);
> > +		pre_ibias = 0x6;
> > +		imp_en = 0xf;
> > +		hdmi_ibias = hdmi_phy->ibias_up;
> > +	}
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON4,
> > -			  (0x3 << PRD_IBIAS_CLK_SHIFT) |
> > -			  (0x3 << PRD_IBIAS_D2_SHIFT) |
> > -			  (0x3 << PRD_IBIAS_D1_SHIFT) |
> > -			  (0x3 << PRD_IBIAS_D0_SHIFT),
> > +			  (pre_ibias << PRD_IBIAS_CLK_SHIFT) |
> > +			  (pre_ibias << PRD_IBIAS_D2_SHIFT) |
> > +			  (pre_ibias << PRD_IBIAS_D1_SHIFT) |
> > +			  (pre_ibias << PRD_IBIAS_D0_SHIFT),
> >  			  RG_HDMITX_PRD_IBIAS_CLK |
> >  			  RG_HDMITX_PRD_IBIAS_D2 |
> >  			  RG_HDMITX_PRD_IBIAS_D1 |
> >  			  RG_HDMITX_PRD_IBIAS_D0);
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON3,
> > -			  (0x0 << DRV_IMP_EN_SHIFT), RG_HDMITX_DRV_IMP_EN);
> > +			  (imp_en << DRV_IMP_EN_SHIFT),
> > +			  RG_HDMITX_DRV_IMP_EN);
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON6,
> >  			  (hdmi_phy->drv_imp_clk << DRV_IMP_CLK_SHIFT) |
> >  			  (hdmi_phy->drv_imp_d2 << DRV_IMP_D2_SHIFT) |
> > @@ -318,12 +334,14 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> >  			  RG_HDMITX_DRV_IMP_CLK | RG_HDMITX_DRV_IMP_D2 |
> >  			  RG_HDMITX_DRV_IMP_D1 | RG_HDMITX_DRV_IMP_D0);
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON5,
> > -			  (hdmi_phy->ibias << DRV_IBIAS_CLK_SHIFT) |
> > -			  (hdmi_phy->ibias << DRV_IBIAS_D2_SHIFT) |
> > -			  (hdmi_phy->ibias << DRV_IBIAS_D1_SHIFT) |
> > -			  (hdmi_phy->ibias << DRV_IBIAS_D0_SHIFT),
> > -			  RG_HDMITX_DRV_IBIAS_CLK | RG_HDMITX_DRV_IBIAS_D2 |
> > -			  RG_HDMITX_DRV_IBIAS_D1 | RG_HDMITX_DRV_IBIAS_D0);
> > +			  (hdmi_ibias << DRV_IBIAS_CLK_SHIFT) |
> > +			  (hdmi_ibias << DRV_IBIAS_D2_SHIFT) |
> > +			  (hdmi_ibias << DRV_IBIAS_D1_SHIFT) |
> > +			  (hdmi_ibias << DRV_IBIAS_D0_SHIFT),
> > +			  RG_HDMITX_DRV_IBIAS_CLK |
> > +			  RG_HDMITX_DRV_IBIAS_D2 |
> > +			  RG_HDMITX_DRV_IBIAS_D1 |
> > +			  RG_HDMITX_DRV_IBIAS_D0);
> >  	return 0;
> >  }
> >  
> 
> 

-- 
Bibby

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 2/3] drm/mediatek: enhance the HDMI driving current

[Bibby Hsieh]

Hi, Philipp,

Thanks for your review.

On Wed, 2016-07-27 at 11:25 +0200, Philipp Zabel wrote:
> Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> > From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > 
> > In order to improve 4K resolution performance,
> > we have to enhance the HDMI driving currend
>                                            ^
> Typo, s/currend/current/
> 
> Besides that, this patch looks good to me.
> 
Ok, I will fix that, thanks.
> regards
> Philipp
> 
> > when clock rate is greater than 165MHz.
> > 
> > Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++++++++++++++-------
> >  1 file changed, 30 insertions(+), 12 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> > index 8a24754..51cb9cf 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> > @@ -265,6 +265,9 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> >  	struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
> >  	unsigned int pre_div;
> >  	unsigned int div;
> > +	unsigned int pre_ibias;
> > +	unsigned int hdmi_ibias;
> > +	unsigned int imp_en;
> >  
> >  	dev_dbg(hdmi_phy->dev, "%s: %lu Hz, parent: %lu Hz\n", __func__,
> >  		rate, parent_rate);
> > @@ -298,18 +301,31 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> >  			  (0x1 << PLL_BR_SHIFT),
> >  			  RG_HDMITX_PLL_BP | RG_HDMITX_PLL_BC |
> >  			  RG_HDMITX_PLL_BR);
> > -	mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3, RG_HDMITX_PRD_IMP_EN);
> > +	if (rate < 165000000) {
> > +		mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3,
> > +					RG_HDMITX_PRD_IMP_EN);
> > +		pre_ibias = 0x3;
> > +		imp_en = 0x0;
> > +		hdmi_ibias = hdmi_phy->ibias;
> > +	} else {
> > +		mtk_hdmi_phy_set_bits(hdmi_phy, HDMI_CON3,
> > +				      RG_HDMITX_PRD_IMP_EN);
> > +		pre_ibias = 0x6;
> > +		imp_en = 0xf;
> > +		hdmi_ibias = hdmi_phy->ibias_up;
> > +	}
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON4,
> > -			  (0x3 << PRD_IBIAS_CLK_SHIFT) |
> > -			  (0x3 << PRD_IBIAS_D2_SHIFT) |
> > -			  (0x3 << PRD_IBIAS_D1_SHIFT) |
> > -			  (0x3 << PRD_IBIAS_D0_SHIFT),
> > +			  (pre_ibias << PRD_IBIAS_CLK_SHIFT) |
> > +			  (pre_ibias << PRD_IBIAS_D2_SHIFT) |
> > +			  (pre_ibias << PRD_IBIAS_D1_SHIFT) |
> > +			  (pre_ibias << PRD_IBIAS_D0_SHIFT),
> >  			  RG_HDMITX_PRD_IBIAS_CLK |
> >  			  RG_HDMITX_PRD_IBIAS_D2 |
> >  			  RG_HDMITX_PRD_IBIAS_D1 |
> >  			  RG_HDMITX_PRD_IBIAS_D0);
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON3,
> > -			  (0x0 << DRV_IMP_EN_SHIFT), RG_HDMITX_DRV_IMP_EN);
> > +			  (imp_en << DRV_IMP_EN_SHIFT),
> > +			  RG_HDMITX_DRV_IMP_EN);
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON6,
> >  			  (hdmi_phy->drv_imp_clk << DRV_IMP_CLK_SHIFT) |
> >  			  (hdmi_phy->drv_imp_d2 << DRV_IMP_D2_SHIFT) |
> > @@ -318,12 +334,14 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> >  			  RG_HDMITX_DRV_IMP_CLK | RG_HDMITX_DRV_IMP_D2 |
> >  			  RG_HDMITX_DRV_IMP_D1 | RG_HDMITX_DRV_IMP_D0);
> >  	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON5,
> > -			  (hdmi_phy->ibias << DRV_IBIAS_CLK_SHIFT) |
> > -			  (hdmi_phy->ibias << DRV_IBIAS_D2_SHIFT) |
> > -			  (hdmi_phy->ibias << DRV_IBIAS_D1_SHIFT) |
> > -			  (hdmi_phy->ibias << DRV_IBIAS_D0_SHIFT),
> > -			  RG_HDMITX_DRV_IBIAS_CLK | RG_HDMITX_DRV_IBIAS_D2 |
> > -			  RG_HDMITX_DRV_IBIAS_D1 | RG_HDMITX_DRV_IBIAS_D0);
> > +			  (hdmi_ibias << DRV_IBIAS_CLK_SHIFT) |
> > +			  (hdmi_ibias << DRV_IBIAS_D2_SHIFT) |
> > +			  (hdmi_ibias << DRV_IBIAS_D1_SHIFT) |
> > +			  (hdmi_ibias << DRV_IBIAS_D0_SHIFT),
> > +			  RG_HDMITX_DRV_IBIAS_CLK |
> > +			  RG_HDMITX_DRV_IBIAS_D2 |
> > +			  RG_HDMITX_DRV_IBIAS_D1 |
> > +			  RG_HDMITX_DRV_IBIAS_D0);
> >  	return 0;
> >  }
> >  
> 
> 

-- 
Bibby

Re: [PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Bibby Hsieh]

Hi, Philipp,

Thanks for your comments.

On Wed, 2016-07-27 at 11:23 +0200, Philipp Zabel wrote:
> Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> > From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > 
> > Pixel clock should be 297MHz when resolution is 4K.
> 
> This patch does two different things, please don't conflate them.
> 
> First, it adds support for 16*3 and 2*3 factors between PLL and pixel
> clock. This should be a separate patch and does what this patch
> description says.
> 
> The second part moves the clocks into an array and adds an indirection
> to clock registration depending on of_match_node. This should be a
> separate patch. I suppose this change is in preparation for mt2701
> support, but I'm not sure yet if it is needed at all.
> 

Ok, I will move the change for mt2701 to another patch and send it until
mt2701 start upstream.

> regards
> Philipp
> 
> > Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
> >  1 file changed, 96 insertions(+), 53 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> > index d05ca79..fa390e0 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> > @@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
> >  	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
> >  };
> >  
> > +enum mtk_dpi_clk_id {
> > +	MTK_DPI_CLK_DPI_ENGINE,
> > +	MTK_DPI_CLK_DPI_PIXEL,
> > +	MTK_DPI_CLK_TVD_PLL,
> > +	MTK_DPI_CLK_COUNT,
> > +};
> > +
> > +static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
> > +	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
> > +	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
> > +	[MTK_DPI_CLK_TVD_PLL] = "pll",
> > +};
> > +
> >  struct mtk_dpi {
> >  	struct mtk_ddp_comp ddp_comp;
> >  	struct drm_encoder encoder;
> >  	void __iomem *regs;
> >  	struct device *dev;
> > -	struct clk *engine_clk;
> > -	struct clk *pixel_clk;
> > -	struct clk *tvd_clk;
> > +	struct clk *clk[MTK_DPI_CLK_COUNT];
> >  	int irq;
> >  	struct drm_display_mode mode;
> >  	enum mtk_dpi_out_color_format color_format;
> > @@ -76,6 +87,7 @@ struct mtk_dpi {
> >  	enum mtk_dpi_out_channel_swap channel_swap;
> >  	bool power_sta;
> >  	u8 power_ctl;
> > +	void *data;
> >  };
> >  
> >  static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
> > @@ -114,6 +126,10 @@ struct mtk_dpi_yc_limit {
> >  	u16 c_bottom;
> >  };
> >  
> > +struct mtk_dpi_conf {
> > +	int (*clk_config)(struct mtk_dpi *dpi, struct drm_display_mode *mode);
> > +};
> > +
> >  static void mtk_dpi_mask(struct mtk_dpi *dpi, u32 offset, u32 val, u32 mask)
> >  {
> >  	u32 tmp = readl(dpi->regs + offset) & ~mask;
> > @@ -377,8 +393,8 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
> >  		return;
> >  
> >  	mtk_dpi_disable(dpi);
> > -	clk_disable_unprepare(dpi->pixel_clk);
> > -	clk_disable_unprepare(dpi->engine_clk);
> > +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
> > +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
> >  	dpi->power_sta = false;
> >  }
> >  
> > @@ -395,13 +411,13 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
> >  	if (dpi->power_sta)
> >  		return 0;
> >  
> > -	ret = clk_prepare_enable(dpi->engine_clk);
> > +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
> >  	if (ret) {
> >  		dev_err(dpi->dev, "Failed to enable engine clock: %d\n", ret);
> >  		goto err_eng;
> >  	}
> >  
> > -	ret = clk_prepare_enable(dpi->pixel_clk);
> > +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
> >  	if (ret) {
> >  		dev_err(dpi->dev, "Failed to enable pixel clock: %d\n", ret);
> >  		goto err_pixel;
> > @@ -412,7 +428,7 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
> >  	return 0;
> >  
> >  err_pixel:
> > -	clk_disable_unprepare(dpi->engine_clk);
> > +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
> >  err_eng:
> >  	dpi->power_ctl &= ~pctl;
> >  	return ret;
> > @@ -428,34 +444,18 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
> >  	struct mtk_dpi_sync_param vsync_leven = { 0 };
> >  	struct mtk_dpi_sync_param vsync_rodd = { 0 };
> >  	struct mtk_dpi_sync_param vsync_reven = { 0 };
> > -	unsigned long pix_rate;
> > -	unsigned long pll_rate;
> > -	unsigned int factor;
> > +	struct mtk_dpi_conf *conf;
> > +	int ret;
> >  
> >  	if (!dpi) {
> >  		dev_err(dpi->dev, "invalid argument\n");
> >  		return -EINVAL;
> >  	}
> >  
> > -	pix_rate = 1000UL * mode->clock;
> > -	if (mode->clock <= 74000)
> > -		factor = 8 * 3;
> > -	else
> > -		factor = 4 * 3;
> > -	pll_rate = pix_rate * factor;
> > -
> > -	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> > -		pll_rate, pix_rate);
> > -
> > -	clk_set_rate(dpi->tvd_clk, pll_rate);
> > -	pll_rate = clk_get_rate(dpi->tvd_clk);
> > -
> > -	pix_rate = pll_rate / factor;
> > -	clk_set_rate(dpi->pixel_clk, pix_rate);
> > -	pix_rate = clk_get_rate(dpi->pixel_clk);
> > -
> > -	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> > -		pll_rate, pix_rate);
> > +	conf = (struct mtk_dpi_conf *)dpi->data;
> > +	ret = conf->clk_config(dpi, mode);
> > +	if (ret)
> > +		dev_err(dpi->dev, "dpi clk set fail\n");
> >  
> >  	limit.c_bottom = 0x0010;
> >  	limit.c_top = 0x0FE0;
> > @@ -656,20 +656,83 @@ static const struct component_ops mtk_dpi_component_ops = {
> >  	.unbind = mtk_dpi_unbind,
> >  };
> >  
> > +static int mtk_dpi_parse_clk_from_dt(struct mtk_dpi *dpi,
> > +				     struct device_node *np)
> > +{
> > +	int i;
> > +
> > +	for (i = 0; i < ARRAY_SIZE(mtk_dpi_clk_names); i++) {
> > +		dpi->clk[i] = of_clk_get_by_name(np,
> > +						  mtk_dpi_clk_names[i]);
> > +		if (IS_ERR(dpi->clk[i]))
> > +			return PTR_ERR(dpi->clk[i]);
> > +	}
> > +	return 0;
> > +}
> > +
> > +static int mt8173_clk_config(struct mtk_dpi *dpi, struct drm_display_mode *mode)
> > +{
> > +	unsigned long pix_rate;
> > +	unsigned long pll_rate;
> > +	unsigned int factor;
> > +
> > +	pix_rate = 1000UL * mode->clock;
> > +	if (mode->clock <= 27000)
> > +		factor = 16 * 3;
> > +	else if (mode->clock <= 74250)
> > +		factor = 8 * 3;
> > +	else if (mode->clock <= 167000)
> > +		factor = 4 * 3;
> > +	else
> > +		factor = 2 * 3;
> > +	pll_rate = pix_rate * factor;
> > +
> > +	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> > +		pll_rate, pix_rate);
> > +
> > +	pll_rate = clk_get_rate(dpi->clk[MTK_DPI_CLK_TVD_PLL]);
> > +	pix_rate = pll_rate / factor;
> > +	clk_set_rate(dpi->clk[MTK_DPI_CLK_DPI_PIXEL], pix_rate);
> > +	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> > +		pll_rate, pix_rate);
> > +
> > +	return 0;
> > +}
> > +
> > +static const struct mtk_dpi_conf mt8173_conf = {
> > +	.clk_config = mt8173_clk_config,
> > +};
> > +
> > +static const struct of_device_id mtk_dpi_of_ids[] = {
> > +	{ .compatible = "mediatek,mt8173-dpi",
> > +		.data = &mt8173_conf,
> > +	},
> > +	{}
> > +};
> > +
> >  static int mtk_dpi_probe(struct platform_device *pdev)
> >  {
> >  	struct device *dev = &pdev->dev;
> >  	struct mtk_dpi *dpi;
> >  	struct resource *mem;
> > +	struct device_node *np = dev->of_node;
> >  	struct device_node *ep, *bridge_node = NULL;
> >  	int comp_id;
> > +	const struct of_device_id *match;
> > +	struct mtk_dpi_conf *conf;
> >  	int ret;
> >  
> > +	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
> > +	if (!match)
> > +		return -ENODEV;
> > +
> >  	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
> >  	if (!dpi)
> >  		return -ENOMEM;
> >  
> >  	dpi->dev = dev;
> > +	dpi->data = (void *)match->data;
> > +	conf = (struct mtk_dpi_conf *)match->data;
> >  
> >  	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> >  	dpi->regs = devm_ioremap_resource(dev, mem);
> > @@ -679,24 +742,9 @@ static int mtk_dpi_probe(struct platform_device *pdev)
> >  		return ret;
> >  	}
> >  
> > -	dpi->engine_clk = devm_clk_get(dev, "engine");
> > -	if (IS_ERR(dpi->engine_clk)) {
> > -		ret = PTR_ERR(dpi->engine_clk);
> > -		dev_err(dev, "Failed to get engine clock: %d\n", ret);
> > -		return ret;
> > -	}
> > -
> > -	dpi->pixel_clk = devm_clk_get(dev, "pixel");
> > -	if (IS_ERR(dpi->pixel_clk)) {
> > -		ret = PTR_ERR(dpi->pixel_clk);
> > -		dev_err(dev, "Failed to get pixel clock: %d\n", ret);
> > -		return ret;
> > -	}
> > -
> > -	dpi->tvd_clk = devm_clk_get(dev, "pll");
> > -	if (IS_ERR(dpi->tvd_clk)) {
> > -		ret = PTR_ERR(dpi->tvd_clk);
> > -		dev_err(dev, "Failed to get tvdpll clock: %d\n", ret);
> > +	ret = mtk_dpi_parse_clk_from_dt(dpi, np);
> > +	if (ret) {
> > +		dev_err(dev, "parse tvd div clk failed!");
> >  		return ret;
> >  	}
> >  
> > @@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
> >  	return 0;
> >  }
> >  
> > -static const struct of_device_id mtk_dpi_of_ids[] = {
> > -	{ .compatible = "mediatek,mt8173-dpi", },
> > -	{}
> > -};
> > -
> >  struct platform_driver mtk_dpi_driver = {
> >  	.probe = mtk_dpi_probe,
> >  	.remove = mtk_dpi_remove,
> 
> 

-- 
Bibby

Re: [PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Bibby Hsieh]

Hi, Philipp,

Thanks for your comments.

On Wed, 2016-07-27 at 11:23 +0200, Philipp Zabel wrote:
> Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> > From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > 
> > Pixel clock should be 297MHz when resolution is 4K.
> 
> This patch does two different things, please don't conflate them.
> 
> First, it adds support for 16*3 and 2*3 factors between PLL and pixel
> clock. This should be a separate patch and does what this patch
> description says.
> 
> The second part moves the clocks into an array and adds an indirection
> to clock registration depending on of_match_node. This should be a
> separate patch. I suppose this change is in preparation for mt2701
> support, but I'm not sure yet if it is needed at all.
> 

Ok, I will move the change for mt2701 to another patch and send it until
mt2701 start upstream.

> regards
> Philipp
> 
> > Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
> >  1 file changed, 96 insertions(+), 53 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> > index d05ca79..fa390e0 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> > @@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
> >  	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
> >  };
> >  
> > +enum mtk_dpi_clk_id {
> > +	MTK_DPI_CLK_DPI_ENGINE,
> > +	MTK_DPI_CLK_DPI_PIXEL,
> > +	MTK_DPI_CLK_TVD_PLL,
> > +	MTK_DPI_CLK_COUNT,
> > +};
> > +
> > +static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
> > +	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
> > +	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
> > +	[MTK_DPI_CLK_TVD_PLL] = "pll",
> > +};
> > +
> >  struct mtk_dpi {
> >  	struct mtk_ddp_comp ddp_comp;
> >  	struct drm_encoder encoder;
> >  	void __iomem *regs;
> >  	struct device *dev;
> > -	struct clk *engine_clk;
> > -	struct clk *pixel_clk;
> > -	struct clk *tvd_clk;
> > +	struct clk *clk[MTK_DPI_CLK_COUNT];
> >  	int irq;
> >  	struct drm_display_mode mode;
> >  	enum mtk_dpi_out_color_format color_format;
> > @@ -76,6 +87,7 @@ struct mtk_dpi {
> >  	enum mtk_dpi_out_channel_swap channel_swap;
> >  	bool power_sta;
> >  	u8 power_ctl;
> > +	void *data;
> >  };
> >  
> >  static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
> > @@ -114,6 +126,10 @@ struct mtk_dpi_yc_limit {
> >  	u16 c_bottom;
> >  };
> >  
> > +struct mtk_dpi_conf {
> > +	int (*clk_config)(struct mtk_dpi *dpi, struct drm_display_mode *mode);
> > +};
> > +
> >  static void mtk_dpi_mask(struct mtk_dpi *dpi, u32 offset, u32 val, u32 mask)
> >  {
> >  	u32 tmp = readl(dpi->regs + offset) & ~mask;
> > @@ -377,8 +393,8 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
> >  		return;
> >  
> >  	mtk_dpi_disable(dpi);
> > -	clk_disable_unprepare(dpi->pixel_clk);
> > -	clk_disable_unprepare(dpi->engine_clk);
> > +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
> > +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
> >  	dpi->power_sta = false;
> >  }
> >  
> > @@ -395,13 +411,13 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
> >  	if (dpi->power_sta)
> >  		return 0;
> >  
> > -	ret = clk_prepare_enable(dpi->engine_clk);
> > +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
> >  	if (ret) {
> >  		dev_err(dpi->dev, "Failed to enable engine clock: %d\n", ret);
> >  		goto err_eng;
> >  	}
> >  
> > -	ret = clk_prepare_enable(dpi->pixel_clk);
> > +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
> >  	if (ret) {
> >  		dev_err(dpi->dev, "Failed to enable pixel clock: %d\n", ret);
> >  		goto err_pixel;
> > @@ -412,7 +428,7 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
> >  	return 0;
> >  
> >  err_pixel:
> > -	clk_disable_unprepare(dpi->engine_clk);
> > +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
> >  err_eng:
> >  	dpi->power_ctl &= ~pctl;
> >  	return ret;
> > @@ -428,34 +444,18 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
> >  	struct mtk_dpi_sync_param vsync_leven = { 0 };
> >  	struct mtk_dpi_sync_param vsync_rodd = { 0 };
> >  	struct mtk_dpi_sync_param vsync_reven = { 0 };
> > -	unsigned long pix_rate;
> > -	unsigned long pll_rate;
> > -	unsigned int factor;
> > +	struct mtk_dpi_conf *conf;
> > +	int ret;
> >  
> >  	if (!dpi) {
> >  		dev_err(dpi->dev, "invalid argument\n");
> >  		return -EINVAL;
> >  	}
> >  
> > -	pix_rate = 1000UL * mode->clock;
> > -	if (mode->clock <= 74000)
> > -		factor = 8 * 3;
> > -	else
> > -		factor = 4 * 3;
> > -	pll_rate = pix_rate * factor;
> > -
> > -	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> > -		pll_rate, pix_rate);
> > -
> > -	clk_set_rate(dpi->tvd_clk, pll_rate);
> > -	pll_rate = clk_get_rate(dpi->tvd_clk);
> > -
> > -	pix_rate = pll_rate / factor;
> > -	clk_set_rate(dpi->pixel_clk, pix_rate);
> > -	pix_rate = clk_get_rate(dpi->pixel_clk);
> > -
> > -	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> > -		pll_rate, pix_rate);
> > +	conf = (struct mtk_dpi_conf *)dpi->data;
> > +	ret = conf->clk_config(dpi, mode);
> > +	if (ret)
> > +		dev_err(dpi->dev, "dpi clk set fail\n");
> >  
> >  	limit.c_bottom = 0x0010;
> >  	limit.c_top = 0x0FE0;
> > @@ -656,20 +656,83 @@ static const struct component_ops mtk_dpi_component_ops = {
> >  	.unbind = mtk_dpi_unbind,
> >  };
> >  
> > +static int mtk_dpi_parse_clk_from_dt(struct mtk_dpi *dpi,
> > +				     struct device_node *np)
> > +{
> > +	int i;
> > +
> > +	for (i = 0; i < ARRAY_SIZE(mtk_dpi_clk_names); i++) {
> > +		dpi->clk[i] = of_clk_get_by_name(np,
> > +						  mtk_dpi_clk_names[i]);
> > +		if (IS_ERR(dpi->clk[i]))
> > +			return PTR_ERR(dpi->clk[i]);
> > +	}
> > +	return 0;
> > +}
> > +
> > +static int mt8173_clk_config(struct mtk_dpi *dpi, struct drm_display_mode *mode)
> > +{
> > +	unsigned long pix_rate;
> > +	unsigned long pll_rate;
> > +	unsigned int factor;
> > +
> > +	pix_rate = 1000UL * mode->clock;
> > +	if (mode->clock <= 27000)
> > +		factor = 16 * 3;
> > +	else if (mode->clock <= 74250)
> > +		factor = 8 * 3;
> > +	else if (mode->clock <= 167000)
> > +		factor = 4 * 3;
> > +	else
> > +		factor = 2 * 3;
> > +	pll_rate = pix_rate * factor;
> > +
> > +	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> > +		pll_rate, pix_rate);
> > +
> > +	pll_rate = clk_get_rate(dpi->clk[MTK_DPI_CLK_TVD_PLL]);
> > +	pix_rate = pll_rate / factor;
> > +	clk_set_rate(dpi->clk[MTK_DPI_CLK_DPI_PIXEL], pix_rate);
> > +	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> > +		pll_rate, pix_rate);
> > +
> > +	return 0;
> > +}
> > +
> > +static const struct mtk_dpi_conf mt8173_conf = {
> > +	.clk_config = mt8173_clk_config,
> > +};
> > +
> > +static const struct of_device_id mtk_dpi_of_ids[] = {
> > +	{ .compatible = "mediatek,mt8173-dpi",
> > +		.data = &mt8173_conf,
> > +	},
> > +	{}
> > +};
> > +
> >  static int mtk_dpi_probe(struct platform_device *pdev)
> >  {
> >  	struct device *dev = &pdev->dev;
> >  	struct mtk_dpi *dpi;
> >  	struct resource *mem;
> > +	struct device_node *np = dev->of_node;
> >  	struct device_node *ep, *bridge_node = NULL;
> >  	int comp_id;
> > +	const struct of_device_id *match;
> > +	struct mtk_dpi_conf *conf;
> >  	int ret;
> >  
> > +	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
> > +	if (!match)
> > +		return -ENODEV;
> > +
> >  	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
> >  	if (!dpi)
> >  		return -ENOMEM;
> >  
> >  	dpi->dev = dev;
> > +	dpi->data = (void *)match->data;
> > +	conf = (struct mtk_dpi_conf *)match->data;
> >  
> >  	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> >  	dpi->regs = devm_ioremap_resource(dev, mem);
> > @@ -679,24 +742,9 @@ static int mtk_dpi_probe(struct platform_device *pdev)
> >  		return ret;
> >  	}
> >  
> > -	dpi->engine_clk = devm_clk_get(dev, "engine");
> > -	if (IS_ERR(dpi->engine_clk)) {
> > -		ret = PTR_ERR(dpi->engine_clk);
> > -		dev_err(dev, "Failed to get engine clock: %d\n", ret);
> > -		return ret;
> > -	}
> > -
> > -	dpi->pixel_clk = devm_clk_get(dev, "pixel");
> > -	if (IS_ERR(dpi->pixel_clk)) {
> > -		ret = PTR_ERR(dpi->pixel_clk);
> > -		dev_err(dev, "Failed to get pixel clock: %d\n", ret);
> > -		return ret;
> > -	}
> > -
> > -	dpi->tvd_clk = devm_clk_get(dev, "pll");
> > -	if (IS_ERR(dpi->tvd_clk)) {
> > -		ret = PTR_ERR(dpi->tvd_clk);
> > -		dev_err(dev, "Failed to get tvdpll clock: %d\n", ret);
> > +	ret = mtk_dpi_parse_clk_from_dt(dpi, np);
> > +	if (ret) {
> > +		dev_err(dev, "parse tvd div clk failed!");
> >  		return ret;
> >  	}
> >  
> > @@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
> >  	return 0;
> >  }
> >  
> > -static const struct of_device_id mtk_dpi_of_ids[] = {
> > -	{ .compatible = "mediatek,mt8173-dpi", },
> > -	{}
> > -};
> > -
> >  struct platform_driver mtk_dpi_driver = {
> >  	.probe = mtk_dpi_probe,
> >  	.remove = mtk_dpi_remove,
> 
> 

-- 
Bibby

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Bibby Hsieh]

Hi, Philipp,

Thanks for your comments.

On Wed, 2016-07-27 at 11:23 +0200, Philipp Zabel wrote:
> Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> > From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > 
> > Pixel clock should be 297MHz when resolution is 4K.
> 
> This patch does two different things, please don't conflate them.
> 
> First, it adds support for 16*3 and 2*3 factors between PLL and pixel
> clock. This should be a separate patch and does what this patch
> description says.
> 
> The second part moves the clocks into an array and adds an indirection
> to clock registration depending on of_match_node. This should be a
> separate patch. I suppose this change is in preparation for mt2701
> support, but I'm not sure yet if it is needed at all.
> 

Ok, I will move the change for mt2701 to another patch and send it until
mt2701 start upstream.

> regards
> Philipp
> 
> > Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> > Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
> >  1 file changed, 96 insertions(+), 53 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> > index d05ca79..fa390e0 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> > @@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
> >  	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
> >  };
> >  
> > +enum mtk_dpi_clk_id {
> > +	MTK_DPI_CLK_DPI_ENGINE,
> > +	MTK_DPI_CLK_DPI_PIXEL,
> > +	MTK_DPI_CLK_TVD_PLL,
> > +	MTK_DPI_CLK_COUNT,
> > +};
> > +
> > +static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
> > +	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
> > +	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
> > +	[MTK_DPI_CLK_TVD_PLL] = "pll",
> > +};
> > +
> >  struct mtk_dpi {
> >  	struct mtk_ddp_comp ddp_comp;
> >  	struct drm_encoder encoder;
> >  	void __iomem *regs;
> >  	struct device *dev;
> > -	struct clk *engine_clk;
> > -	struct clk *pixel_clk;
> > -	struct clk *tvd_clk;
> > +	struct clk *clk[MTK_DPI_CLK_COUNT];
> >  	int irq;
> >  	struct drm_display_mode mode;
> >  	enum mtk_dpi_out_color_format color_format;
> > @@ -76,6 +87,7 @@ struct mtk_dpi {
> >  	enum mtk_dpi_out_channel_swap channel_swap;
> >  	bool power_sta;
> >  	u8 power_ctl;
> > +	void *data;
> >  };
> >  
> >  static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
> > @@ -114,6 +126,10 @@ struct mtk_dpi_yc_limit {
> >  	u16 c_bottom;
> >  };
> >  
> > +struct mtk_dpi_conf {
> > +	int (*clk_config)(struct mtk_dpi *dpi, struct drm_display_mode *mode);
> > +};
> > +
> >  static void mtk_dpi_mask(struct mtk_dpi *dpi, u32 offset, u32 val, u32 mask)
> >  {
> >  	u32 tmp = readl(dpi->regs + offset) & ~mask;
> > @@ -377,8 +393,8 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
> >  		return;
> >  
> >  	mtk_dpi_disable(dpi);
> > -	clk_disable_unprepare(dpi->pixel_clk);
> > -	clk_disable_unprepare(dpi->engine_clk);
> > +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
> > +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
> >  	dpi->power_sta = false;
> >  }
> >  
> > @@ -395,13 +411,13 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
> >  	if (dpi->power_sta)
> >  		return 0;
> >  
> > -	ret = clk_prepare_enable(dpi->engine_clk);
> > +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
> >  	if (ret) {
> >  		dev_err(dpi->dev, "Failed to enable engine clock: %d\n", ret);
> >  		goto err_eng;
> >  	}
> >  
> > -	ret = clk_prepare_enable(dpi->pixel_clk);
> > +	ret = clk_prepare_enable(dpi->clk[MTK_DPI_CLK_DPI_PIXEL]);
> >  	if (ret) {
> >  		dev_err(dpi->dev, "Failed to enable pixel clock: %d\n", ret);
> >  		goto err_pixel;
> > @@ -412,7 +428,7 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi, enum mtk_dpi_power_ctl pctl)
> >  	return 0;
> >  
> >  err_pixel:
> > -	clk_disable_unprepare(dpi->engine_clk);
> > +	clk_disable_unprepare(dpi->clk[MTK_DPI_CLK_DPI_ENGINE]);
> >  err_eng:
> >  	dpi->power_ctl &= ~pctl;
> >  	return ret;
> > @@ -428,34 +444,18 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
> >  	struct mtk_dpi_sync_param vsync_leven = { 0 };
> >  	struct mtk_dpi_sync_param vsync_rodd = { 0 };
> >  	struct mtk_dpi_sync_param vsync_reven = { 0 };
> > -	unsigned long pix_rate;
> > -	unsigned long pll_rate;
> > -	unsigned int factor;
> > +	struct mtk_dpi_conf *conf;
> > +	int ret;
> >  
> >  	if (!dpi) {
> >  		dev_err(dpi->dev, "invalid argument\n");
> >  		return -EINVAL;
> >  	}
> >  
> > -	pix_rate = 1000UL * mode->clock;
> > -	if (mode->clock <= 74000)
> > -		factor = 8 * 3;
> > -	else
> > -		factor = 4 * 3;
> > -	pll_rate = pix_rate * factor;
> > -
> > -	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> > -		pll_rate, pix_rate);
> > -
> > -	clk_set_rate(dpi->tvd_clk, pll_rate);
> > -	pll_rate = clk_get_rate(dpi->tvd_clk);
> > -
> > -	pix_rate = pll_rate / factor;
> > -	clk_set_rate(dpi->pixel_clk, pix_rate);
> > -	pix_rate = clk_get_rate(dpi->pixel_clk);
> > -
> > -	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> > -		pll_rate, pix_rate);
> > +	conf = (struct mtk_dpi_conf *)dpi->data;
> > +	ret = conf->clk_config(dpi, mode);
> > +	if (ret)
> > +		dev_err(dpi->dev, "dpi clk set fail\n");
> >  
> >  	limit.c_bottom = 0x0010;
> >  	limit.c_top = 0x0FE0;
> > @@ -656,20 +656,83 @@ static const struct component_ops mtk_dpi_component_ops = {
> >  	.unbind = mtk_dpi_unbind,
> >  };
> >  
> > +static int mtk_dpi_parse_clk_from_dt(struct mtk_dpi *dpi,
> > +				     struct device_node *np)
> > +{
> > +	int i;
> > +
> > +	for (i = 0; i < ARRAY_SIZE(mtk_dpi_clk_names); i++) {
> > +		dpi->clk[i] = of_clk_get_by_name(np,
> > +						  mtk_dpi_clk_names[i]);
> > +		if (IS_ERR(dpi->clk[i]))
> > +			return PTR_ERR(dpi->clk[i]);
> > +	}
> > +	return 0;
> > +}
> > +
> > +static int mt8173_clk_config(struct mtk_dpi *dpi, struct drm_display_mode *mode)
> > +{
> > +	unsigned long pix_rate;
> > +	unsigned long pll_rate;
> > +	unsigned int factor;
> > +
> > +	pix_rate = 1000UL * mode->clock;
> > +	if (mode->clock <= 27000)
> > +		factor = 16 * 3;
> > +	else if (mode->clock <= 74250)
> > +		factor = 8 * 3;
> > +	else if (mode->clock <= 167000)
> > +		factor = 4 * 3;
> > +	else
> > +		factor = 2 * 3;
> > +	pll_rate = pix_rate * factor;
> > +
> > +	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
> > +		pll_rate, pix_rate);
> > +
> > +	pll_rate = clk_get_rate(dpi->clk[MTK_DPI_CLK_TVD_PLL]);
> > +	pix_rate = pll_rate / factor;
> > +	clk_set_rate(dpi->clk[MTK_DPI_CLK_DPI_PIXEL], pix_rate);
> > +	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> > +		pll_rate, pix_rate);
> > +
> > +	return 0;
> > +}
> > +
> > +static const struct mtk_dpi_conf mt8173_conf = {
> > +	.clk_config = mt8173_clk_config,
> > +};
> > +
> > +static const struct of_device_id mtk_dpi_of_ids[] = {
> > +	{ .compatible = "mediatek,mt8173-dpi",
> > +		.data = &mt8173_conf,
> > +	},
> > +	{}
> > +};
> > +
> >  static int mtk_dpi_probe(struct platform_device *pdev)
> >  {
> >  	struct device *dev = &pdev->dev;
> >  	struct mtk_dpi *dpi;
> >  	struct resource *mem;
> > +	struct device_node *np = dev->of_node;
> >  	struct device_node *ep, *bridge_node = NULL;
> >  	int comp_id;
> > +	const struct of_device_id *match;
> > +	struct mtk_dpi_conf *conf;
> >  	int ret;
> >  
> > +	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
> > +	if (!match)
> > +		return -ENODEV;
> > +
> >  	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
> >  	if (!dpi)
> >  		return -ENOMEM;
> >  
> >  	dpi->dev = dev;
> > +	dpi->data = (void *)match->data;
> > +	conf = (struct mtk_dpi_conf *)match->data;
> >  
> >  	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> >  	dpi->regs = devm_ioremap_resource(dev, mem);
> > @@ -679,24 +742,9 @@ static int mtk_dpi_probe(struct platform_device *pdev)
> >  		return ret;
> >  	}
> >  
> > -	dpi->engine_clk = devm_clk_get(dev, "engine");
> > -	if (IS_ERR(dpi->engine_clk)) {
> > -		ret = PTR_ERR(dpi->engine_clk);
> > -		dev_err(dev, "Failed to get engine clock: %d\n", ret);
> > -		return ret;
> > -	}
> > -
> > -	dpi->pixel_clk = devm_clk_get(dev, "pixel");
> > -	if (IS_ERR(dpi->pixel_clk)) {
> > -		ret = PTR_ERR(dpi->pixel_clk);
> > -		dev_err(dev, "Failed to get pixel clock: %d\n", ret);
> > -		return ret;
> > -	}
> > -
> > -	dpi->tvd_clk = devm_clk_get(dev, "pll");
> > -	if (IS_ERR(dpi->tvd_clk)) {
> > -		ret = PTR_ERR(dpi->tvd_clk);
> > -		dev_err(dev, "Failed to get tvdpll clock: %d\n", ret);
> > +	ret = mtk_dpi_parse_clk_from_dt(dpi, np);
> > +	if (ret) {
> > +		dev_err(dev, "parse tvd div clk failed!");
> >  		return ret;
> >  	}
> >  
> > @@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
> >  	return 0;
> >  }
> >  
> > -static const struct of_device_id mtk_dpi_of_ids[] = {
> > -	{ .compatible = "mediatek,mt8173-dpi", },
> > -	{}
> > -};
> > -
> >  struct platform_driver mtk_dpi_driver = {
> >  	.probe = mtk_dpi_probe,
> >  	.remove = mtk_dpi_remove,
> 
> 

-- 
Bibby

Re: [PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 4010 bytes --]

On Wed, Jul 27, 2016 at 04:31:32PM +0800, Bibby Hsieh wrote:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> Pixel clock should be 297MHz when resolution is 4K.
> 
> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
>  1 file changed, 96 insertions(+), 53 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index d05ca79..fa390e0 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
>  	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
>  };
>  
> +enum mtk_dpi_clk_id {
> +	MTK_DPI_CLK_DPI_ENGINE,
> +	MTK_DPI_CLK_DPI_PIXEL,
> +	MTK_DPI_CLK_TVD_PLL,
> +	MTK_DPI_CLK_COUNT,
> +};
> +
> +static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
> +	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
> +	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
> +	[MTK_DPI_CLK_TVD_PLL] = "pll",
> +};
> +
>  struct mtk_dpi {
>  	struct mtk_ddp_comp ddp_comp;
>  	struct drm_encoder encoder;
>  	void __iomem *regs;
>  	struct device *dev;
> -	struct clk *engine_clk;
> -	struct clk *pixel_clk;
> -	struct clk *tvd_clk;
> +	struct clk *clk[MTK_DPI_CLK_COUNT];

This looks to me like a step backwards. All accesses to these clocks are
now very clumsy and I don't see any advantage in using this array rather
than individually named clocks.

Also, that change seems completely unrelated to the description in the
commit message.

>  	int irq;
>  	struct drm_display_mode mode;
>  	enum mtk_dpi_out_color_format color_format;
> @@ -76,6 +87,7 @@ struct mtk_dpi {
>  	enum mtk_dpi_out_channel_swap channel_swap;
>  	bool power_sta;
>  	u8 power_ctl;
> +	void *data;

This should probably be const. It's a bad idea to cast away the const
from the of_device_id.data that this is assigned from.

> +static const struct of_device_id mtk_dpi_of_ids[] = {
> +	{ .compatible = "mediatek,mt8173-dpi",
> +		.data = &mt8173_conf,
> +	},

Please align this in some standard way. It all fits on one line, so the
most obvious choice would've been:

	{ .compatible = "mediatek,mt8173-dpi", .data = &mt8173_conf },

> +	{}
> +};
> +
>  static int mtk_dpi_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct mtk_dpi *dpi;
>  	struct resource *mem;
> +	struct device_node *np = dev->of_node;
>  	struct device_node *ep, *bridge_node = NULL;
>  	int comp_id;
> +	const struct of_device_id *match;
> +	struct mtk_dpi_conf *conf;
>  	int ret;
>  
> +	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
> +	if (!match)
> +		return -ENODEV;

You introduce a variable np = dev->of_node above, but then you add code
that uses dev->of_node directly?

That said, you should use of_device_get_match_data() anyway, so that you
can omit...

> +
>  	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
>  	if (!dpi)
>  		return -ENOMEM;
>  
>  	dpi->dev = dev;
> +	dpi->data = (void *)match->data;
> +	conf = (struct mtk_dpi_conf *)match->data;

... the dereferences here. Also, like I said before you should make
dpi->data and conf both const to avoid casting away the constness of the
data. If you do that you can even drop the casts because you'd be
casting from a const void * to a const foo *, which gets casted
automatically.

> @@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
>  	return 0;
>  }
>  
> -static const struct of_device_id mtk_dpi_of_ids[] = {
> -	{ .compatible = "mediatek,mt8173-dpi", },
> -	{}
> -};

Another advantage of using of_device_get_match_data() is that it doesn't
need direct access to the of_device_id table (it'll obtain it via an
indirect dev->driver->of_match_table), so you don't have to move this
around and make this patch overall less churn.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Thierry Reding]

[-- Attachment #1.1: Type: text/plain, Size: 4010 bytes --]

On Wed, Jul 27, 2016 at 04:31:32PM +0800, Bibby Hsieh wrote:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> Pixel clock should be 297MHz when resolution is 4K.
> 
> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
>  1 file changed, 96 insertions(+), 53 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index d05ca79..fa390e0 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
>  	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
>  };
>  
> +enum mtk_dpi_clk_id {
> +	MTK_DPI_CLK_DPI_ENGINE,
> +	MTK_DPI_CLK_DPI_PIXEL,
> +	MTK_DPI_CLK_TVD_PLL,
> +	MTK_DPI_CLK_COUNT,
> +};
> +
> +static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
> +	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
> +	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
> +	[MTK_DPI_CLK_TVD_PLL] = "pll",
> +};
> +
>  struct mtk_dpi {
>  	struct mtk_ddp_comp ddp_comp;
>  	struct drm_encoder encoder;
>  	void __iomem *regs;
>  	struct device *dev;
> -	struct clk *engine_clk;
> -	struct clk *pixel_clk;
> -	struct clk *tvd_clk;
> +	struct clk *clk[MTK_DPI_CLK_COUNT];

This looks to me like a step backwards. All accesses to these clocks are
now very clumsy and I don't see any advantage in using this array rather
than individually named clocks.

Also, that change seems completely unrelated to the description in the
commit message.

>  	int irq;
>  	struct drm_display_mode mode;
>  	enum mtk_dpi_out_color_format color_format;
> @@ -76,6 +87,7 @@ struct mtk_dpi {
>  	enum mtk_dpi_out_channel_swap channel_swap;
>  	bool power_sta;
>  	u8 power_ctl;
> +	void *data;

This should probably be const. It's a bad idea to cast away the const
from the of_device_id.data that this is assigned from.

> +static const struct of_device_id mtk_dpi_of_ids[] = {
> +	{ .compatible = "mediatek,mt8173-dpi",
> +		.data = &mt8173_conf,
> +	},

Please align this in some standard way. It all fits on one line, so the
most obvious choice would've been:

	{ .compatible = "mediatek,mt8173-dpi", .data = &mt8173_conf },

> +	{}
> +};
> +
>  static int mtk_dpi_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct mtk_dpi *dpi;
>  	struct resource *mem;
> +	struct device_node *np = dev->of_node;
>  	struct device_node *ep, *bridge_node = NULL;
>  	int comp_id;
> +	const struct of_device_id *match;
> +	struct mtk_dpi_conf *conf;
>  	int ret;
>  
> +	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
> +	if (!match)
> +		return -ENODEV;

You introduce a variable np = dev->of_node above, but then you add code
that uses dev->of_node directly?

That said, you should use of_device_get_match_data() anyway, so that you
can omit...

> +
>  	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
>  	if (!dpi)
>  		return -ENOMEM;
>  
>  	dpi->dev = dev;
> +	dpi->data = (void *)match->data;
> +	conf = (struct mtk_dpi_conf *)match->data;

... the dereferences here. Also, like I said before you should make
dpi->data and conf both const to avoid casting away the constness of the
data. If you do that you can even drop the casts because you'd be
casting from a const void * to a const foo *, which gets casted
automatically.

> @@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
>  	return 0;
>  }
>  
> -static const struct of_device_id mtk_dpi_of_ids[] = {
> -	{ .compatible = "mediatek,mt8173-dpi", },
> -	{}
> -};

Another advantage of using of_device_get_match_data() is that it doesn't
need direct access to the of_device_id table (it'll obtain it via an
indirect dev->driver->of_match_table), so you don't have to move this
around and make this patch overall less churn.

Thierry

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[-- Attachment #2: Type: text/plain, Size: 160 bytes --]

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Thierry Reding]

On Wed, Jul 27, 2016 at 04:31:32PM +0800, Bibby Hsieh wrote:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> Pixel clock should be 297MHz when resolution is 4K.
> 
> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c |  149 +++++++++++++++++++++++-------------
>  1 file changed, 96 insertions(+), 53 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index d05ca79..fa390e0 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -60,14 +60,25 @@ enum mtk_dpi_out_color_format {
>  	MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL
>  };
>  
> +enum mtk_dpi_clk_id {
> +	MTK_DPI_CLK_DPI_ENGINE,
> +	MTK_DPI_CLK_DPI_PIXEL,
> +	MTK_DPI_CLK_TVD_PLL,
> +	MTK_DPI_CLK_COUNT,
> +};
> +
> +static const char * const mtk_dpi_clk_names[MTK_DPI_CLK_COUNT] = {
> +	[MTK_DPI_CLK_DPI_ENGINE] = "engine",
> +	[MTK_DPI_CLK_DPI_PIXEL] = "pixel",
> +	[MTK_DPI_CLK_TVD_PLL] = "pll",
> +};
> +
>  struct mtk_dpi {
>  	struct mtk_ddp_comp ddp_comp;
>  	struct drm_encoder encoder;
>  	void __iomem *regs;
>  	struct device *dev;
> -	struct clk *engine_clk;
> -	struct clk *pixel_clk;
> -	struct clk *tvd_clk;
> +	struct clk *clk[MTK_DPI_CLK_COUNT];

This looks to me like a step backwards. All accesses to these clocks are
now very clumsy and I don't see any advantage in using this array rather
than individually named clocks.

Also, that change seems completely unrelated to the description in the
commit message.

>  	int irq;
>  	struct drm_display_mode mode;
>  	enum mtk_dpi_out_color_format color_format;
> @@ -76,6 +87,7 @@ struct mtk_dpi {
>  	enum mtk_dpi_out_channel_swap channel_swap;
>  	bool power_sta;
>  	u8 power_ctl;
> +	void *data;

This should probably be const. It's a bad idea to cast away the const
from the of_device_id.data that this is assigned from.

> +static const struct of_device_id mtk_dpi_of_ids[] = {
> +	{ .compatible = "mediatek,mt8173-dpi",
> +		.data = &mt8173_conf,
> +	},

Please align this in some standard way. It all fits on one line, so the
most obvious choice would've been:

	{ .compatible = "mediatek,mt8173-dpi", .data = &mt8173_conf },

> +	{}
> +};
> +
>  static int mtk_dpi_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct mtk_dpi *dpi;
>  	struct resource *mem;
> +	struct device_node *np = dev->of_node;
>  	struct device_node *ep, *bridge_node = NULL;
>  	int comp_id;
> +	const struct of_device_id *match;
> +	struct mtk_dpi_conf *conf;
>  	int ret;
>  
> +	match = of_match_node(mtk_dpi_of_ids, dev->of_node);
> +	if (!match)
> +		return -ENODEV;

You introduce a variable np = dev->of_node above, but then you add code
that uses dev->of_node directly?

That said, you should use of_device_get_match_data() anyway, so that you
can omit...

> +
>  	dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
>  	if (!dpi)
>  		return -ENOMEM;
>  
>  	dpi->dev = dev;
> +	dpi->data = (void *)match->data;
> +	conf = (struct mtk_dpi_conf *)match->data;

... the dereferences here. Also, like I said before you should make
dpi->data and conf both const to avoid casting away the constness of the
data. If you do that you can even drop the casts because you'd be
casting from a const void * to a const foo *, which gets casted
automatically.

> @@ -754,11 +802,6 @@ static int mtk_dpi_remove(struct platform_device *pdev)
>  	return 0;
>  }
>  
> -static const struct of_device_id mtk_dpi_of_ids[] = {
> -	{ .compatible = "mediatek,mt8173-dpi", },
> -	{}
> -};

Another advantage of using of_device_get_match_data() is that it doesn't
need direct access to the of_device_id table (it'll obtain it via an
indirect dev->driver->of_match_table), so you don't have to move this
around and make this patch overall less churn.

Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160729/de5bab71/attachment.sig>