[PATCH v8 0/3] da8xx USB PHY platform devices and clocks

[PATCH v8 0/3] da8xx USB PHY platform devices and clocks

[David Lechner]

I reworked the "[PATCH v6 4/5] ARM: DTS: da850: Add cfgchip syscon node" and
"[PATCH v6 5/5] ARM: DTS: da850: Add usb phy node" patches that were dropped
from linux-davinci into the new "ARM: dts: da850: Add cfgchip syscon node"
patch. This should be OK unless it is decided that the BayLibre guys should
rework it so that the entire SYSCFG0 is a single syscon device. I don't see
any compelling reason to do that though.

v8 changes:
* Dropped v7 patches that have been accepted into linux-davinci already
* New patch for CFGCHIP syscon/USB PHY DT node
* Rebased other patches

v7 changes:
* Dropped v6 patches that have been accepted into linux-davinci already
* New patch for adding device names to clock lookup tables
* Picked up related patch from Axel Haslam for registering USB PHY clocks on
  device tree boards and added error checking to to that patch
* Rebased on latest linux-davinci + linux-next
* Added devices instead of NULL in clk_get() where appropriate usb-da8xx.c
* Re-ordered patches so that they apply/build cleanly

v6 changes:

* Combine "ARM: davinci: da8xx: Enable the usb20 "per" clk on phy_clk_enable"
  from the "[PATCH/RFT v2 00/17] Add DT support for ohci-da8xx" series with
  the "ARM: davinci: da8xx: add usb phy clocks" patch in this series.
* Change the syscon and da8xx-usb-phy device ids to -1.

v5 changes: renamed "usbphy" to "usb_phy" or "usb-phy" as appropriate

v4 changes: fix strict checkpatch complaint

v3 changes:

* Fixed the davinci device tree declarations to use the preferred DT address
  convention so that the items I have added can be correct too.
* Moved that davinci clock init so that we don't have to call ioremap in the
  clock mux functions.
* Added a new "syscon" device for the CFGCHIP registers. This is used by the
  USB PHY driver and will be used in the future in common clock framework
  drivers.
* USB clocks are moved to a common file instead of having duplicated code.
* PHY driver uses syscon for CFGCHIP registers instead of using them directly.

Axel Haslam (1):
  ARM: davinci: da8xx: register USB PHY clocks in the DT file

David Lechner (2):
  ARM: dts: da850: Add cfgchip syscon node
  ARM: davinci: da8xx: add usb phy clocks

 arch/arm/boot/dts/da850.dtsi                |  10 ++
 arch/arm/mach-davinci/board-da830-evm.c     |  31 +---
 arch/arm/mach-davinci/board-omapl138-hawk.c |  15 +-
 arch/arm/mach-davinci/da8xx-dt.c            |  12 ++
 arch/arm/mach-davinci/include/mach/da8xx.h  |   3 +
 arch/arm/mach-davinci/usb-da8xx.c           | 267 ++++++++++++++++++++++++++--
 6 files changed, 296 insertions(+), 42 deletions(-)

-- 
2.7.4

[PATCH v8 0/3] da8xx USB PHY platform devices and clocks

[David Lechner]

I reworked the "[PATCH v6 4/5] ARM: DTS: da850: Add cfgchip syscon node" and
"[PATCH v6 5/5] ARM: DTS: da850: Add usb phy node" patches that were dropped
from linux-davinci into the new "ARM: dts: da850: Add cfgchip syscon node"
patch. This should be OK unless it is decided that the BayLibre guys should
rework it so that the entire SYSCFG0 is a single syscon device. I don't see
any compelling reason to do that though.

v8 changes:
* Dropped v7 patches that have been accepted into linux-davinci already
* New patch for CFGCHIP syscon/USB PHY DT node
* Rebased other patches

v7 changes:
* Dropped v6 patches that have been accepted into linux-davinci already
* New patch for adding device names to clock lookup tables
* Picked up related patch from Axel Haslam for registering USB PHY clocks on
  device tree boards and added error checking to to that patch
* Rebased on latest linux-davinci + linux-next
* Added devices instead of NULL in clk_get() where appropriate usb-da8xx.c
* Re-ordered patches so that they apply/build cleanly

v6 changes:

* Combine "ARM: davinci: da8xx: Enable the usb20 "per" clk on phy_clk_enable"
  from the "[PATCH/RFT v2 00/17] Add DT support for ohci-da8xx" series with
  the "ARM: davinci: da8xx: add usb phy clocks" patch in this series.
* Change the syscon and da8xx-usb-phy device ids to -1.

v5 changes: renamed "usbphy" to "usb_phy" or "usb-phy" as appropriate

v4 changes: fix strict checkpatch complaint

v3 changes:

* Fixed the davinci device tree declarations to use the preferred DT address
  convention so that the items I have added can be correct too.
* Moved that davinci clock init so that we don't have to call ioremap in the
  clock mux functions.
* Added a new "syscon" device for the CFGCHIP registers. This is used by the
  USB PHY driver and will be used in the future in common clock framework
  drivers.
* USB clocks are moved to a common file instead of having duplicated code.
* PHY driver uses syscon for CFGCHIP registers instead of using them directly.

Axel Haslam (1):
  ARM: davinci: da8xx: register USB PHY clocks in the DT file

David Lechner (2):
  ARM: dts: da850: Add cfgchip syscon node
  ARM: davinci: da8xx: add usb phy clocks

 arch/arm/boot/dts/da850.dtsi                |  10 ++
 arch/arm/mach-davinci/board-da830-evm.c     |  31 +---
 arch/arm/mach-davinci/board-omapl138-hawk.c |  15 +-
 arch/arm/mach-davinci/da8xx-dt.c            |  12 ++
 arch/arm/mach-davinci/include/mach/da8xx.h  |   3 +
 arch/arm/mach-davinci/usb-da8xx.c           | 267 ++++++++++++++++++++++++++--
 6 files changed, 296 insertions(+), 42 deletions(-)

-- 
2.7.4

[PATCH v8 1/3] ARM: dts: da850: Add cfgchip syscon node

[David Lechner]

Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
for the USB PHY that is part of this range of registers.

Also have to add OF_DEV_AUXDATA() entry so that clock lookup will work for
the the USB PHY driver.

Signed-off-by: David Lechner <david@lechnology.com>
---
 arch/arm/boot/dts/da850.dtsi     | 10 ++++++++++
 arch/arm/mach-davinci/da8xx-dt.c |  1 +
 2 files changed, 11 insertions(+)

diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index 4c83613..2534aab 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -209,6 +209,16 @@
 			};
 
 		};
+		cfgchip: chip-controller@1417c {
+			compatible = "ti,da830-cfgchip", "syscon", "simple-mfd";
+			reg = <0x1417c 0x14>;
+
+			usb_phy: usb-phy {
+				compatible = "ti,da830-usb-phy";
+				#phy-cells = <1>;
+				status = "disabled";
+			};
+		};
 		edma0: edma@0 {
 			compatible = "ti,edma3-tpcc";
 			/* eDMA3 CC0: 0x01c0 0000 - 0x01c0 7fff */
diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
index aec569f9..20fa842 100644
--- a/arch/arm/mach-davinci/da8xx-dt.c
+++ b/arch/arm/mach-davinci/da8xx-dt.c
@@ -41,6 +41,7 @@ static struct of_dev_auxdata da850_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("ti,da850-tilcdc", 0x01e13000, "da8xx_lcdc.0", NULL),
 	OF_DEV_AUXDATA("ti,da830-ohci", 0x01e25000, "ohci", NULL),
 	OF_DEV_AUXDATA("ti,da830-musb", 0x01e00000, "musb-da8xx", NULL),
+	OF_DEV_AUXDATA("ti,da830-usb-phy", 0x01c1417c, "da8xx-usb-phy", NULL),
 	{}
 };
 
-- 
2.7.4

[PATCH v8 1/3] ARM: dts: da850: Add cfgchip syscon node

[David Lechner]

Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
for the USB PHY that is part of this range of registers.

Also have to add OF_DEV_AUXDATA() entry so that clock lookup will work for
the the USB PHY driver.

Signed-off-by: David Lechner <david@lechnology.com>
---
 arch/arm/boot/dts/da850.dtsi     | 10 ++++++++++
 arch/arm/mach-davinci/da8xx-dt.c |  1 +
 2 files changed, 11 insertions(+)

diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index 4c83613..2534aab 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -209,6 +209,16 @@
 			};
 
 		};
+		cfgchip: chip-controller at 1417c {
+			compatible = "ti,da830-cfgchip", "syscon", "simple-mfd";
+			reg = <0x1417c 0x14>;
+
+			usb_phy: usb-phy {
+				compatible = "ti,da830-usb-phy";
+				#phy-cells = <1>;
+				status = "disabled";
+			};
+		};
 		edma0: edma at 0 {
 			compatible = "ti,edma3-tpcc";
 			/* eDMA3 CC0: 0x01c0 0000 - 0x01c0 7fff */
diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
index aec569f9..20fa842 100644
--- a/arch/arm/mach-davinci/da8xx-dt.c
+++ b/arch/arm/mach-davinci/da8xx-dt.c
@@ -41,6 +41,7 @@ static struct of_dev_auxdata da850_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("ti,da850-tilcdc", 0x01e13000, "da8xx_lcdc.0", NULL),
 	OF_DEV_AUXDATA("ti,da830-ohci", 0x01e25000, "ohci", NULL),
 	OF_DEV_AUXDATA("ti,da830-musb", 0x01e00000, "musb-da8xx", NULL),
+	OF_DEV_AUXDATA("ti,da830-usb-phy", 0x01c1417c, "da8xx-usb-phy", NULL),
 	{}
 };
 
-- 
2.7.4

[PATCH v8 1/3] ARM: dts: da850: Add cfgchip syscon node

[David Lechner]

Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
for the USB PHY that is part of this range of registers.

Also have to add OF_DEV_AUXDATA() entry so that clock lookup will work for
the the USB PHY driver.

Signed-off-by: David Lechner <david-nq/r/kbU++upp/zk7JDF2g@public.gmane.org>
---
 arch/arm/boot/dts/da850.dtsi     | 10 ++++++++++
 arch/arm/mach-davinci/da8xx-dt.c |  1 +
 2 files changed, 11 insertions(+)

diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index 4c83613..2534aab 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -209,6 +209,16 @@
 			};
 
 		};
+		cfgchip: chip-controller@1417c {
+			compatible = "ti,da830-cfgchip", "syscon", "simple-mfd";
+			reg = <0x1417c 0x14>;
+
+			usb_phy: usb-phy {
+				compatible = "ti,da830-usb-phy";
+				#phy-cells = <1>;
+				status = "disabled";
+			};
+		};
 		edma0: edma@0 {
 			compatible = "ti,edma3-tpcc";
 			/* eDMA3 CC0: 0x01c0 0000 - 0x01c0 7fff */
diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
index aec569f9..20fa842 100644
--- a/arch/arm/mach-davinci/da8xx-dt.c
+++ b/arch/arm/mach-davinci/da8xx-dt.c
@@ -41,6 +41,7 @@ static struct of_dev_auxdata da850_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("ti,da850-tilcdc", 0x01e13000, "da8xx_lcdc.0", NULL),
 	OF_DEV_AUXDATA("ti,da830-ohci", 0x01e25000, "ohci", NULL),
 	OF_DEV_AUXDATA("ti,da830-musb", 0x01e00000, "musb-da8xx", NULL),
+	OF_DEV_AUXDATA("ti,da830-usb-phy", 0x01c1417c, "da8xx-usb-phy", NULL),
 	{}
 };
 
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v8 1/3] ARM: dts: da850: Add cfgchip syscon node

[Sekhar Nori]

Hi David,

On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
> Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
> for the USB PHY that is part of this range of registers.
> 
> Also have to add OF_DEV_AUXDATA() entry so that clock lookup will work for
> the the USB PHY driver.
> 
> Signed-off-by: David Lechner <david@lechnology.com>

For future, please do not combine device-tree addition and other C code into a 
single patch. I have applied this patch while splitting it into two as 
attached.

Thanks,
Sekhar

---8<---
From: David Lechner <david@lechnology.com>
Date: Mon, 31 Oct 2016 15:47:19 -0500
Subject: [PATCH] ARM: dts: da850: Add cfgchip syscon node

Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
for the USB PHY that is part of this range of registers.

Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: drop OF_DEV_AUXDATA() addition]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
---
 arch/arm/boot/dts/da850.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index 4c836133a183..2534aab851e1 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -209,6 +209,16 @@
 			};
 
 		};
+		cfgchip: chip-controller@1417c {
+			compatible = "ti,da830-cfgchip", "syscon", "simple-mfd";
+			reg = <0x1417c 0x14>;
+
+			usb_phy: usb-phy {
+				compatible = "ti,da830-usb-phy";
+				#phy-cells = <1>;
+				status = "disabled";
+			};
+		};
 		edma0: edma@0 {
 			compatible = "ti,edma3-tpcc";
 			/* eDMA3 CC0: 0x01c0 0000 - 0x01c0 7fff */
-- 
2.9.0

---8<---
From: David Lechner <david@lechnology.com>
Date: Mon, 31 Oct 2016 15:47:19 -0500
Subject: [PATCH] ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for USB phy

Add OF_DEV_AUXDATA() entry for USB phy. This is required for
so that clock lookup will work for the USB PHY driver.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
---
 arch/arm/mach-davinci/da8xx-dt.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
index 0e45cbd57273..5e67618180a7 100644
--- a/arch/arm/mach-davinci/da8xx-dt.c
+++ b/arch/arm/mach-davinci/da8xx-dt.c
@@ -41,6 +41,7 @@ static struct of_dev_auxdata da850_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("ti,da850-tilcdc", 0x01e13000, "da8xx_lcdc.0", NULL),
 	OF_DEV_AUXDATA("ti,da830-ohci", 0x01e25000, "ohci", NULL),
 	OF_DEV_AUXDATA("ti,da830-musb", 0x01e00000, "musb-da8xx", NULL),
+	OF_DEV_AUXDATA("ti,da830-usb-phy", 0x01c1417c, "da8xx-usb-phy", NULL),
 	{}
 };
 
-- 
2.9.0

[PATCH v8 1/3] ARM: dts: da850: Add cfgchip syscon node

[Sekhar Nori]

Hi David,

On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
> Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
> for the USB PHY that is part of this range of registers.
> 
> Also have to add OF_DEV_AUXDATA() entry so that clock lookup will work for
> the the USB PHY driver.
> 
> Signed-off-by: David Lechner <david@lechnology.com>

For future, please do not combine device-tree addition and other C code into a 
single patch. I have applied this patch while splitting it into two as 
attached.

Thanks,
Sekhar

---8<---
From: David Lechner <david@lechnology.com>
Date: Mon, 31 Oct 2016 15:47:19 -0500
Subject: [PATCH] ARM: dts: da850: Add cfgchip syscon node

Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
for the USB PHY that is part of this range of registers.

Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar at ti.com: drop OF_DEV_AUXDATA() addition]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
---
 arch/arm/boot/dts/da850.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index 4c836133a183..2534aab851e1 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -209,6 +209,16 @@
 			};
 
 		};
+		cfgchip: chip-controller at 1417c {
+			compatible = "ti,da830-cfgchip", "syscon", "simple-mfd";
+			reg = <0x1417c 0x14>;
+
+			usb_phy: usb-phy {
+				compatible = "ti,da830-usb-phy";
+				#phy-cells = <1>;
+				status = "disabled";
+			};
+		};
 		edma0: edma at 0 {
 			compatible = "ti,edma3-tpcc";
 			/* eDMA3 CC0: 0x01c0 0000 - 0x01c0 7fff */
-- 
2.9.0

---8<---
From: David Lechner <david@lechnology.com>
Date: Mon, 31 Oct 2016 15:47:19 -0500
Subject: [PATCH] ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for USB phy

Add OF_DEV_AUXDATA() entry for USB phy. This is required for
so that clock lookup will work for the USB PHY driver.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
---
 arch/arm/mach-davinci/da8xx-dt.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
index 0e45cbd57273..5e67618180a7 100644
--- a/arch/arm/mach-davinci/da8xx-dt.c
+++ b/arch/arm/mach-davinci/da8xx-dt.c
@@ -41,6 +41,7 @@ static struct of_dev_auxdata da850_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("ti,da850-tilcdc", 0x01e13000, "da8xx_lcdc.0", NULL),
 	OF_DEV_AUXDATA("ti,da830-ohci", 0x01e25000, "ohci", NULL),
 	OF_DEV_AUXDATA("ti,da830-musb", 0x01e00000, "musb-da8xx", NULL),
+	OF_DEV_AUXDATA("ti,da830-usb-phy", 0x01c1417c, "da8xx-usb-phy", NULL),
 	{}
 };
 
-- 
2.9.0

Re: [PATCH v8 1/3] ARM: dts: da850: Add cfgchip syscon node

[Sekhar Nori]

Hi David,

On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
> Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
> for the USB PHY that is part of this range of registers.
> 
> Also have to add OF_DEV_AUXDATA() entry so that clock lookup will work for
> the the USB PHY driver.
> 
> Signed-off-by: David Lechner <david@lechnology.com>

For future, please do not combine device-tree addition and other C code into a 
single patch. I have applied this patch while splitting it into two as 
attached.

Thanks,
Sekhar

---8<---
From: David Lechner <david@lechnology.com>
Date: Mon, 31 Oct 2016 15:47:19 -0500
Subject: [PATCH] ARM: dts: da850: Add cfgchip syscon node

Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
for the USB PHY that is part of this range of registers.

Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: drop OF_DEV_AUXDATA() addition]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
---
 arch/arm/boot/dts/da850.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index 4c836133a183..2534aab851e1 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -209,6 +209,16 @@
 			};
 
 		};
+		cfgchip: chip-controller@1417c {
+			compatible = "ti,da830-cfgchip", "syscon", "simple-mfd";
+			reg = <0x1417c 0x14>;
+
+			usb_phy: usb-phy {
+				compatible = "ti,da830-usb-phy";
+				#phy-cells = <1>;
+				status = "disabled";
+			};
+		};
 		edma0: edma@0 {
 			compatible = "ti,edma3-tpcc";
 			/* eDMA3 CC0: 0x01c0 0000 - 0x01c0 7fff */
-- 
2.9.0

---8<---
From: David Lechner <david@lechnology.com>
Date: Mon, 31 Oct 2016 15:47:19 -0500
Subject: [PATCH] ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for USB phy

Add OF_DEV_AUXDATA() entry for USB phy. This is required for
so that clock lookup will work for the USB PHY driver.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
---
 arch/arm/mach-davinci/da8xx-dt.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
index 0e45cbd57273..5e67618180a7 100644
--- a/arch/arm/mach-davinci/da8xx-dt.c
+++ b/arch/arm/mach-davinci/da8xx-dt.c
@@ -41,6 +41,7 @@ static struct of_dev_auxdata da850_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("ti,da850-tilcdc", 0x01e13000, "da8xx_lcdc.0", NULL),
 	OF_DEV_AUXDATA("ti,da830-ohci", 0x01e25000, "ohci", NULL),
 	OF_DEV_AUXDATA("ti,da830-musb", 0x01e00000, "musb-da8xx", NULL),
+	OF_DEV_AUXDATA("ti,da830-usb-phy", 0x01c1417c, "da8xx-usb-phy", NULL),
 	{}
 };
 
-- 
2.9.0

Re: [PATCH v8 1/3] ARM: dts: da850: Add cfgchip syscon node

[David Lechner]

On 11/01/2016 04:53 AM, Sekhar Nori wrote:
> Hi David,
>
> On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
>> Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
>> for the USB PHY that is part of this range of registers.
>>
>> Also have to add OF_DEV_AUXDATA() entry so that clock lookup will work for
>> the the USB PHY driver.
>>
>> Signed-off-by: David Lechner <david@lechnology.com>
>
> For future, please do not combine device-tree addition and other C code into a
> single patch. I have applied this patch while splitting it into two as
> attached.
>

Sorry. I should know that by now. :-/

Thank you for fixing it for me.

[PATCH v8 1/3] ARM: dts: da850: Add cfgchip syscon node

[David Lechner]

On 11/01/2016 04:53 AM, Sekhar Nori wrote:
> Hi David,
>
> On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
>> Add a syscon node for the SoC CFGCHIPn registers. It includes a child node
>> for the USB PHY that is part of this range of registers.
>>
>> Also have to add OF_DEV_AUXDATA() entry so that clock lookup will work for
>> the the USB PHY driver.
>>
>> Signed-off-by: David Lechner <david@lechnology.com>
>
> For future, please do not combine device-tree addition and other C code into a
> single patch. I have applied this patch while splitting it into two as
> attached.
>

Sorry. I should know that by now. :-/

Thank you for fixing it for me.

[PATCH v8 2/3] ARM: davinci: da8xx: add usb phy clocks

[David Lechner]

Up to this point, the USB phy clock configuration was handled manually in
the board files and in the usb drivers. This adds proper clocks so that
the usb drivers can use clk_get and clk_enable and not have to worry about
the details. Also, the related code is removed from the board files and
replaced with the new clock registration functions.

This also removes the #if IS_ENABLED(CONFIG_USB_MUSB_HDRC) around the musb
declaration and renames the musb platform device so that we can reference
it from the usb20 clock even if the musb device is not used.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
---
 arch/arm/mach-davinci/board-da830-evm.c     |  31 +---
 arch/arm/mach-davinci/board-omapl138-hawk.c |  15 +-
 arch/arm/mach-davinci/include/mach/da8xx.h  |   3 +
 arch/arm/mach-davinci/usb-da8xx.c           | 267 ++++++++++++++++++++++++++--
 4 files changed, 274 insertions(+), 42 deletions(-)

diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c
index 53172ad..5db0901 100644
--- a/arch/arm/mach-davinci/board-da830-evm.c
+++ b/arch/arm/mach-davinci/board-da830-evm.c
@@ -18,7 +18,6 @@
 #include <linux/i2c.h>
 #include <linux/i2c/pcf857x.h>
 #include <linux/platform_data/at24.h>
-#include <linux/mfd/da8xx-cfgchip.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/spi/spi.h>
@@ -108,30 +107,18 @@ static irqreturn_t da830_evm_usb_ocic_irq(int irq, void *dev_id)
 
 static __init void da830_evm_usb_init(void)
 {
-	u32 cfgchip2;
 	int ret;
 
-	/*
-	 * Set up USB clock in the CFGCHIP2 register.
-	 * FYI:  CFGCHIP2 is 0x0000ef00 initially.
-	 */
-	cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
-	/* USB2.0 PHY reference clock is 24 MHz */
-	cfgchip2 &= ~CFGCHIP2_REFFREQ_MASK;
-	cfgchip2 |=  CFGCHIP2_REFFREQ_24MHZ;
-
-	/*
-	 * Select internal reference clock for USB 2.0 PHY
-	 * and use it as a clock source for USB 1.1 PHY
-	 * (this is the default setting anyway).
-	 */
-	cfgchip2 &= ~CFGCHIP2_USB1PHYCLKMUX;
-	cfgchip2 |=  CFGCHIP2_USB2PHYCLKMUX;
-
-	__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
 	/* USB_REFCLKIN is not used. */
+	ret = da8xx_register_usb20_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 2.0 PHY CLK registration failed: %d\n",
+			__func__, ret);
+
+	ret = da8xx_register_usb11_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 1.1 PHY CLK registration failed: %d\n",
+			__func__, ret);
 
 	ret = da8xx_register_usb_phy();
 	if (ret)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
index 67477ca..a4e8726 100644
--- a/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -13,7 +13,6 @@
 #include <linux/init.h>
 #include <linux/console.h>
 #include <linux/gpio.h>
-#include <linux/mfd/da8xx-cfgchip.h>
 #include <linux/platform_data/gpio-davinci.h>
 #include <linux/regulator/machine.h>
 
@@ -245,7 +244,6 @@ static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id)
 static __init void omapl138_hawk_usb_init(void)
 {
 	int ret;
-	u32 cfgchip2;
 
 	ret = davinci_cfg_reg_list(da850_hawk_usb11_pins);
 	if (ret) {
@@ -253,12 +251,15 @@ static __init void omapl138_hawk_usb_init(void)
 		return;
 	}
 
-	/* Setup the Ref. clock frequency for the HAWK at 24 MHz. */
+	ret = da8xx_register_usb20_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 2.0 PHY CLK registration failed: %d\n",
+			__func__, ret);
 
-	cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-	cfgchip2 &= ~CFGCHIP2_REFFREQ_MASK;
-	cfgchip2 |=  CFGCHIP2_REFFREQ_24MHZ;
-	__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+	ret = da8xx_register_usb11_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 1.1 PHY CLK registration failed: %d\n",
+			__func__, ret);
 
 	ret = da8xx_register_usb_phy();
 	if (ret)
diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h
index 5e07d06..43322be 100644
--- a/arch/arm/mach-davinci/include/mach/da8xx.h
+++ b/arch/arm/mach-davinci/include/mach/da8xx.h
@@ -92,6 +92,9 @@ int da8xx_register_watchdog(void);
 int da8xx_register_usb_phy(void);
 int da8xx_register_usb20(unsigned mA, unsigned potpgt);
 int da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata);
+int da8xx_register_usb_refclkin(int rate);
+int da8xx_register_usb20_phy_clk(bool use_usb_refclkin);
+int da8xx_register_usb11_phy_clk(bool use_usb_refclkin);
 int da8xx_register_emac(void);
 int da8xx_register_uio_pruss(void);
 int da8xx_register_lcdc(struct da8xx_lcdc_platform_data *pdata);
diff --git a/arch/arm/mach-davinci/usb-da8xx.c b/arch/arm/mach-davinci/usb-da8xx.c
index 4bb1903..b010e5f 100644
--- a/arch/arm/mach-davinci/usb-da8xx.c
+++ b/arch/arm/mach-davinci/usb-da8xx.c
@@ -1,24 +1,38 @@
 /*
  * DA8xx USB
  */
+#include <linux/clk.h>
+#include <linux/delay.h>
 #include <linux/dma-mapping.h>
 #include <linux/init.h>
+#include <linux/mfd/da8xx-cfgchip.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_data/usb-davinci.h>
 #include <linux/platform_device.h>
 #include <linux/usb/musb.h>
 
+#include <mach/clock.h>
 #include <mach/common.h>
 #include <mach/cputype.h>
 #include <mach/da8xx.h>
 #include <mach/irqs.h>
 
+#include "clock.h"
+
 #define DA8XX_USB0_BASE		0x01e00000
 #define DA8XX_USB1_BASE		0x01e25000
 
 static struct platform_device da8xx_usb_phy = {
 	.name		= "da8xx-usb-phy",
 	.id		= -1,
+	.dev		= {
+		/*
+		 * Setting init_name so that clock lookup will work in
+		 * da8xx_register_usb11_phy_clk() even if this device is not
+		 * registered yet.
+		 */
+		.init_name	= "da8xx-usb-phy",
+	},
 };
 
 int __init da8xx_register_usb_phy(void)
@@ -26,8 +40,6 @@ int __init da8xx_register_usb_phy(void)
 	return platform_device_register(&da8xx_usb_phy);
 }
 
-#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
-
 static struct musb_hdrc_config musb_config = {
 	.multipoint	= true,
 	.num_eps	= 5,
@@ -56,10 +68,15 @@ static struct resource da8xx_usb20_resources[] = {
 
 static u64 usb_dmamask = DMA_BIT_MASK(32);
 
-static struct platform_device usb_dev = {
+static struct platform_device da8xx_usb20_dev = {
 	.name		= "musb-da8xx",
 	.id             = -1,
 	.dev = {
+		/*
+		 * Setting init_name so that clock lookup will work in
+		 * usb20_phy_clk_enable() even if this device is not registered.
+		 */
+		.init_name		= "musb-da8xx",
 		.platform_data		= &usb_data,
 		.dma_mask		= &usb_dmamask,
 		.coherent_dma_mask      = DMA_BIT_MASK(32),
@@ -73,18 +90,9 @@ int __init da8xx_register_usb20(unsigned int mA, unsigned int potpgt)
 	usb_data.power	= mA > 510 ? 255 : mA / 2;
 	usb_data.potpgt = (potpgt + 1) / 2;
 
-	return platform_device_register(&usb_dev);
-}
-
-#else
-
-int __init da8xx_register_usb20(unsigned int mA, unsigned int potpgt)
-{
-	return 0;
+	return platform_device_register(&da8xx_usb20_dev);
 }
 
-#endif  /* CONFIG_USB_MUSB_HDRC */
-
 static struct resource da8xx_usb11_resources[] = {
 	[0] = {
 		.start	= DA8XX_USB1_BASE,
@@ -116,3 +124,236 @@ int __init da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata)
 	da8xx_usb11_device.dev.platform_data = pdata;
 	return platform_device_register(&da8xx_usb11_device);
 }
+
+static struct clk usb_refclkin = {
+	.name		= "usb_refclkin",
+	.set_rate	= davinci_simple_set_rate,
+};
+
+static struct clk_lookup usb_refclkin_lookup =
+	CLK(NULL, "usb_refclkin", &usb_refclkin);
+
+/**
+ * da8xx_register_usb_refclkin - register USB_REFCLKIN clock
+ *
+ * @rate: The clock rate in Hz
+ *
+ * This clock is only needed if the board provides an external USB_REFCLKIN
+ * signal, in which case it will be used as the parent of usb20_phy_clk and/or
+ * usb11_phy_clk.
+ */
+int __init da8xx_register_usb_refclkin(int rate)
+{
+	int ret;
+
+	usb_refclkin.rate = rate;
+	ret = clk_register(&usb_refclkin);
+	if (ret)
+		return ret;
+
+	clkdev_add(&usb_refclkin_lookup);
+
+	return 0;
+}
+
+static void usb20_phy_clk_enable(struct clk *clk)
+{
+	struct clk *usb20_clk;
+	int err;
+	u32 val;
+	u32 timeout = 500000; /* 500 msec */
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	usb20_clk = clk_get(&da8xx_usb20_dev.dev, "usb20");
+	if (IS_ERR(usb20_clk)) {
+		pr_err("could not get usb20 clk: %ld\n", PTR_ERR(usb20_clk));
+		return;
+	}
+
+	/* The USB 2.O PLL requires that the USB 2.O PSC is enabled as well. */
+	err = clk_prepare_enable(usb20_clk);
+	if (err) {
+		pr_err("failed to enable usb20 clk: %d\n", err);
+		clk_put(usb20_clk);
+		return;
+	}
+
+	/*
+	 * Turn on the USB 2.0 PHY, but just the PLL, and not OTG. The USB 1.1
+	 * host may use the PLL clock without USB 2.0 OTG being used.
+	 */
+	val &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN);
+	val |= CFGCHIP2_PHY_PLLON;
+
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	while (--timeout) {
+		val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+		if (val & CFGCHIP2_PHYCLKGD)
+			goto done;
+		udelay(1);
+	}
+
+	pr_err("Timeout waiting for USB 2.0 PHY clock good\n");
+done:
+	clk_disable_unprepare(usb20_clk);
+	clk_put(usb20_clk);
+}
+
+static void usb20_phy_clk_disable(struct clk *clk)
+{
+	u32 val;
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+	val |= CFGCHIP2_PHYPWRDN;
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+}
+
+static int usb20_phy_clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	u32 val;
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	/* Set the mux depending on the parent clock. */
+	if (parent == &usb_refclkin) {
+		val &= ~CFGCHIP2_USB2PHYCLKMUX;
+	} else if (strcmp(parent->name, "pll0_aux_clk") == 0) {
+		val |= CFGCHIP2_USB2PHYCLKMUX;
+	} else {
+		pr_err("Bad parent on USB 2.0 PHY clock\n");
+		return -EINVAL;
+	}
+
+	/* reference frequency also comes from parent clock */
+	val &= ~CFGCHIP2_REFFREQ_MASK;
+	switch (clk_get_rate(parent)) {
+	case 12000000:
+		val |= CFGCHIP2_REFFREQ_12MHZ;
+		break;
+	case 13000000:
+		val |= CFGCHIP2_REFFREQ_13MHZ;
+		break;
+	case 19200000:
+		val |= CFGCHIP2_REFFREQ_19_2MHZ;
+		break;
+	case 20000000:
+		val |= CFGCHIP2_REFFREQ_20MHZ;
+		break;
+	case 24000000:
+		val |= CFGCHIP2_REFFREQ_24MHZ;
+		break;
+	case 26000000:
+		val |= CFGCHIP2_REFFREQ_26MHZ;
+		break;
+	case 38400000:
+		val |= CFGCHIP2_REFFREQ_38_4MHZ;
+		break;
+	case 40000000:
+		val |= CFGCHIP2_REFFREQ_40MHZ;
+		break;
+	case 48000000:
+		val |= CFGCHIP2_REFFREQ_48MHZ;
+		break;
+	default:
+		pr_err("Bad parent clock rate on USB 2.0 PHY clock\n");
+		return -EINVAL;
+	}
+
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	return 0;
+}
+
+static struct clk usb20_phy_clk = {
+	.name		= "usb20_phy",
+	.clk_enable	= usb20_phy_clk_enable,
+	.clk_disable	= usb20_phy_clk_disable,
+	.set_parent	= usb20_phy_clk_set_parent,
+};
+
+static struct clk_lookup usb20_phy_clk_lookup =
+	CLK("da8xx-usb-phy", "usb20_phy", &usb20_phy_clk);
+
+/**
+ * da8xx_register_usb20_phy_clk - register USB0PHYCLKMUX clock
+ *
+ * @use_usb_refclkin: Selects the parent clock - either "usb_refclkin" if true
+ *	or "pll0_aux" if false.
+ */
+int __init da8xx_register_usb20_phy_clk(bool use_usb_refclkin)
+{
+	struct clk *parent;
+	int ret = 0;
+
+	parent = clk_get(NULL, use_usb_refclkin ? "usb_refclkin" : "pll0_aux");
+	if (IS_ERR(parent))
+		return PTR_ERR(parent);
+
+	usb20_phy_clk.parent = parent;
+	ret = clk_register(&usb20_phy_clk);
+	if (!ret)
+		clkdev_add(&usb20_phy_clk_lookup);
+
+	clk_put(parent);
+
+	return ret;
+}
+
+static int usb11_phy_clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	u32 val;
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	/* Set the USB 1.1 PHY clock mux based on the parent clock. */
+	if (parent == &usb20_phy_clk) {
+		val &= ~CFGCHIP2_USB1PHYCLKMUX;
+	} else if (parent == &usb_refclkin) {
+		val |= CFGCHIP2_USB1PHYCLKMUX;
+	} else {
+		pr_err("Bad parent on USB 1.1 PHY clock\n");
+		return -EINVAL;
+	}
+
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	return 0;
+}
+
+static struct clk usb11_phy_clk = {
+	.name		= "usb11_phy",
+	.set_parent	= usb11_phy_clk_set_parent,
+};
+
+static struct clk_lookup usb11_phy_clk_lookup =
+	CLK("da8xx-usb-phy", "usb11_phy", &usb11_phy_clk);
+
+/**
+ * da8xx_register_usb11_phy_clk - register USB1PHYCLKMUX clock
+ *
+ * @use_usb_refclkin: Selects the parent clock - either "usb_refclkin" if true
+ *	or "usb20_phy" if false.
+ */
+int __init da8xx_register_usb11_phy_clk(bool use_usb_refclkin)
+{
+	struct clk *parent;
+	int ret = 0;
+
+	if (use_usb_refclkin)
+		parent = clk_get(NULL, "usb_refclkin");
+	else
+		parent = clk_get(&da8xx_usb_phy.dev, "usb20_phy");
+	if (IS_ERR(parent))
+		return PTR_ERR(parent);
+
+	usb11_phy_clk.parent = parent;
+	ret = clk_register(&usb11_phy_clk);
+	if (!ret)
+		clkdev_add(&usb11_phy_clk_lookup);
+
+	clk_put(parent);
+
+	return ret;
+}
-- 
2.7.4

[PATCH v8 2/3] ARM: davinci: da8xx: add usb phy clocks

[David Lechner]

Up to this point, the USB phy clock configuration was handled manually in
the board files and in the usb drivers. This adds proper clocks so that
the usb drivers can use clk_get and clk_enable and not have to worry about
the details. Also, the related code is removed from the board files and
replaced with the new clock registration functions.

This also removes the #if IS_ENABLED(CONFIG_USB_MUSB_HDRC) around the musb
declaration and renames the musb platform device so that we can reference
it from the usb20 clock even if the musb device is not used.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
---
 arch/arm/mach-davinci/board-da830-evm.c     |  31 +---
 arch/arm/mach-davinci/board-omapl138-hawk.c |  15 +-
 arch/arm/mach-davinci/include/mach/da8xx.h  |   3 +
 arch/arm/mach-davinci/usb-da8xx.c           | 267 ++++++++++++++++++++++++++--
 4 files changed, 274 insertions(+), 42 deletions(-)

diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c
index 53172ad..5db0901 100644
--- a/arch/arm/mach-davinci/board-da830-evm.c
+++ b/arch/arm/mach-davinci/board-da830-evm.c
@@ -18,7 +18,6 @@
 #include <linux/i2c.h>
 #include <linux/i2c/pcf857x.h>
 #include <linux/platform_data/at24.h>
-#include <linux/mfd/da8xx-cfgchip.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/spi/spi.h>
@@ -108,30 +107,18 @@ static irqreturn_t da830_evm_usb_ocic_irq(int irq, void *dev_id)
 
 static __init void da830_evm_usb_init(void)
 {
-	u32 cfgchip2;
 	int ret;
 
-	/*
-	 * Set up USB clock in the CFGCHIP2 register.
-	 * FYI:  CFGCHIP2 is 0x0000ef00 initially.
-	 */
-	cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
-	/* USB2.0 PHY reference clock is 24 MHz */
-	cfgchip2 &= ~CFGCHIP2_REFFREQ_MASK;
-	cfgchip2 |=  CFGCHIP2_REFFREQ_24MHZ;
-
-	/*
-	 * Select internal reference clock for USB 2.0 PHY
-	 * and use it as a clock source for USB 1.1 PHY
-	 * (this is the default setting anyway).
-	 */
-	cfgchip2 &= ~CFGCHIP2_USB1PHYCLKMUX;
-	cfgchip2 |=  CFGCHIP2_USB2PHYCLKMUX;
-
-	__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
 	/* USB_REFCLKIN is not used. */
+	ret = da8xx_register_usb20_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 2.0 PHY CLK registration failed: %d\n",
+			__func__, ret);
+
+	ret = da8xx_register_usb11_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 1.1 PHY CLK registration failed: %d\n",
+			__func__, ret);
 
 	ret = da8xx_register_usb_phy();
 	if (ret)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
index 67477ca..a4e8726 100644
--- a/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -13,7 +13,6 @@
 #include <linux/init.h>
 #include <linux/console.h>
 #include <linux/gpio.h>
-#include <linux/mfd/da8xx-cfgchip.h>
 #include <linux/platform_data/gpio-davinci.h>
 #include <linux/regulator/machine.h>
 
@@ -245,7 +244,6 @@ static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id)
 static __init void omapl138_hawk_usb_init(void)
 {
 	int ret;
-	u32 cfgchip2;
 
 	ret = davinci_cfg_reg_list(da850_hawk_usb11_pins);
 	if (ret) {
@@ -253,12 +251,15 @@ static __init void omapl138_hawk_usb_init(void)
 		return;
 	}
 
-	/* Setup the Ref. clock frequency for the HAWK at 24 MHz. */
+	ret = da8xx_register_usb20_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 2.0 PHY CLK registration failed: %d\n",
+			__func__, ret);
 
-	cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-	cfgchip2 &= ~CFGCHIP2_REFFREQ_MASK;
-	cfgchip2 |=  CFGCHIP2_REFFREQ_24MHZ;
-	__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+	ret = da8xx_register_usb11_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 1.1 PHY CLK registration failed: %d\n",
+			__func__, ret);
 
 	ret = da8xx_register_usb_phy();
 	if (ret)
diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h
index 5e07d06..43322be 100644
--- a/arch/arm/mach-davinci/include/mach/da8xx.h
+++ b/arch/arm/mach-davinci/include/mach/da8xx.h
@@ -92,6 +92,9 @@ int da8xx_register_watchdog(void);
 int da8xx_register_usb_phy(void);
 int da8xx_register_usb20(unsigned mA, unsigned potpgt);
 int da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata);
+int da8xx_register_usb_refclkin(int rate);
+int da8xx_register_usb20_phy_clk(bool use_usb_refclkin);
+int da8xx_register_usb11_phy_clk(bool use_usb_refclkin);
 int da8xx_register_emac(void);
 int da8xx_register_uio_pruss(void);
 int da8xx_register_lcdc(struct da8xx_lcdc_platform_data *pdata);
diff --git a/arch/arm/mach-davinci/usb-da8xx.c b/arch/arm/mach-davinci/usb-da8xx.c
index 4bb1903..b010e5f 100644
--- a/arch/arm/mach-davinci/usb-da8xx.c
+++ b/arch/arm/mach-davinci/usb-da8xx.c
@@ -1,24 +1,38 @@
 /*
  * DA8xx USB
  */
+#include <linux/clk.h>
+#include <linux/delay.h>
 #include <linux/dma-mapping.h>
 #include <linux/init.h>
+#include <linux/mfd/da8xx-cfgchip.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_data/usb-davinci.h>
 #include <linux/platform_device.h>
 #include <linux/usb/musb.h>
 
+#include <mach/clock.h>
 #include <mach/common.h>
 #include <mach/cputype.h>
 #include <mach/da8xx.h>
 #include <mach/irqs.h>
 
+#include "clock.h"
+
 #define DA8XX_USB0_BASE		0x01e00000
 #define DA8XX_USB1_BASE		0x01e25000
 
 static struct platform_device da8xx_usb_phy = {
 	.name		= "da8xx-usb-phy",
 	.id		= -1,
+	.dev		= {
+		/*
+		 * Setting init_name so that clock lookup will work in
+		 * da8xx_register_usb11_phy_clk() even if this device is not
+		 * registered yet.
+		 */
+		.init_name	= "da8xx-usb-phy",
+	},
 };
 
 int __init da8xx_register_usb_phy(void)
@@ -26,8 +40,6 @@ int __init da8xx_register_usb_phy(void)
 	return platform_device_register(&da8xx_usb_phy);
 }
 
-#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
-
 static struct musb_hdrc_config musb_config = {
 	.multipoint	= true,
 	.num_eps	= 5,
@@ -56,10 +68,15 @@ static struct resource da8xx_usb20_resources[] = {
 
 static u64 usb_dmamask = DMA_BIT_MASK(32);
 
-static struct platform_device usb_dev = {
+static struct platform_device da8xx_usb20_dev = {
 	.name		= "musb-da8xx",
 	.id             = -1,
 	.dev = {
+		/*
+		 * Setting init_name so that clock lookup will work in
+		 * usb20_phy_clk_enable() even if this device is not registered.
+		 */
+		.init_name		= "musb-da8xx",
 		.platform_data		= &usb_data,
 		.dma_mask		= &usb_dmamask,
 		.coherent_dma_mask      = DMA_BIT_MASK(32),
@@ -73,18 +90,9 @@ int __init da8xx_register_usb20(unsigned int mA, unsigned int potpgt)
 	usb_data.power	= mA > 510 ? 255 : mA / 2;
 	usb_data.potpgt = (potpgt + 1) / 2;
 
-	return platform_device_register(&usb_dev);
-}
-
-#else
-
-int __init da8xx_register_usb20(unsigned int mA, unsigned int potpgt)
-{
-	return 0;
+	return platform_device_register(&da8xx_usb20_dev);
 }
 
-#endif  /* CONFIG_USB_MUSB_HDRC */
-
 static struct resource da8xx_usb11_resources[] = {
 	[0] = {
 		.start	= DA8XX_USB1_BASE,
@@ -116,3 +124,236 @@ int __init da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata)
 	da8xx_usb11_device.dev.platform_data = pdata;
 	return platform_device_register(&da8xx_usb11_device);
 }
+
+static struct clk usb_refclkin = {
+	.name		= "usb_refclkin",
+	.set_rate	= davinci_simple_set_rate,
+};
+
+static struct clk_lookup usb_refclkin_lookup =
+	CLK(NULL, "usb_refclkin", &usb_refclkin);
+
+/**
+ * da8xx_register_usb_refclkin - register USB_REFCLKIN clock
+ *
+ * @rate: The clock rate in Hz
+ *
+ * This clock is only needed if the board provides an external USB_REFCLKIN
+ * signal, in which case it will be used as the parent of usb20_phy_clk and/or
+ * usb11_phy_clk.
+ */
+int __init da8xx_register_usb_refclkin(int rate)
+{
+	int ret;
+
+	usb_refclkin.rate = rate;
+	ret = clk_register(&usb_refclkin);
+	if (ret)
+		return ret;
+
+	clkdev_add(&usb_refclkin_lookup);
+
+	return 0;
+}
+
+static void usb20_phy_clk_enable(struct clk *clk)
+{
+	struct clk *usb20_clk;
+	int err;
+	u32 val;
+	u32 timeout = 500000; /* 500 msec */
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	usb20_clk = clk_get(&da8xx_usb20_dev.dev, "usb20");
+	if (IS_ERR(usb20_clk)) {
+		pr_err("could not get usb20 clk: %ld\n", PTR_ERR(usb20_clk));
+		return;
+	}
+
+	/* The USB 2.O PLL requires that the USB 2.O PSC is enabled as well. */
+	err = clk_prepare_enable(usb20_clk);
+	if (err) {
+		pr_err("failed to enable usb20 clk: %d\n", err);
+		clk_put(usb20_clk);
+		return;
+	}
+
+	/*
+	 * Turn on the USB 2.0 PHY, but just the PLL, and not OTG. The USB 1.1
+	 * host may use the PLL clock without USB 2.0 OTG being used.
+	 */
+	val &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN);
+	val |= CFGCHIP2_PHY_PLLON;
+
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	while (--timeout) {
+		val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+		if (val & CFGCHIP2_PHYCLKGD)
+			goto done;
+		udelay(1);
+	}
+
+	pr_err("Timeout waiting for USB 2.0 PHY clock good\n");
+done:
+	clk_disable_unprepare(usb20_clk);
+	clk_put(usb20_clk);
+}
+
+static void usb20_phy_clk_disable(struct clk *clk)
+{
+	u32 val;
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+	val |= CFGCHIP2_PHYPWRDN;
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+}
+
+static int usb20_phy_clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	u32 val;
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	/* Set the mux depending on the parent clock. */
+	if (parent == &usb_refclkin) {
+		val &= ~CFGCHIP2_USB2PHYCLKMUX;
+	} else if (strcmp(parent->name, "pll0_aux_clk") == 0) {
+		val |= CFGCHIP2_USB2PHYCLKMUX;
+	} else {
+		pr_err("Bad parent on USB 2.0 PHY clock\n");
+		return -EINVAL;
+	}
+
+	/* reference frequency also comes from parent clock */
+	val &= ~CFGCHIP2_REFFREQ_MASK;
+	switch (clk_get_rate(parent)) {
+	case 12000000:
+		val |= CFGCHIP2_REFFREQ_12MHZ;
+		break;
+	case 13000000:
+		val |= CFGCHIP2_REFFREQ_13MHZ;
+		break;
+	case 19200000:
+		val |= CFGCHIP2_REFFREQ_19_2MHZ;
+		break;
+	case 20000000:
+		val |= CFGCHIP2_REFFREQ_20MHZ;
+		break;
+	case 24000000:
+		val |= CFGCHIP2_REFFREQ_24MHZ;
+		break;
+	case 26000000:
+		val |= CFGCHIP2_REFFREQ_26MHZ;
+		break;
+	case 38400000:
+		val |= CFGCHIP2_REFFREQ_38_4MHZ;
+		break;
+	case 40000000:
+		val |= CFGCHIP2_REFFREQ_40MHZ;
+		break;
+	case 48000000:
+		val |= CFGCHIP2_REFFREQ_48MHZ;
+		break;
+	default:
+		pr_err("Bad parent clock rate on USB 2.0 PHY clock\n");
+		return -EINVAL;
+	}
+
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	return 0;
+}
+
+static struct clk usb20_phy_clk = {
+	.name		= "usb20_phy",
+	.clk_enable	= usb20_phy_clk_enable,
+	.clk_disable	= usb20_phy_clk_disable,
+	.set_parent	= usb20_phy_clk_set_parent,
+};
+
+static struct clk_lookup usb20_phy_clk_lookup =
+	CLK("da8xx-usb-phy", "usb20_phy", &usb20_phy_clk);
+
+/**
+ * da8xx_register_usb20_phy_clk - register USB0PHYCLKMUX clock
+ *
+ * @use_usb_refclkin: Selects the parent clock - either "usb_refclkin" if true
+ *	or "pll0_aux" if false.
+ */
+int __init da8xx_register_usb20_phy_clk(bool use_usb_refclkin)
+{
+	struct clk *parent;
+	int ret = 0;
+
+	parent = clk_get(NULL, use_usb_refclkin ? "usb_refclkin" : "pll0_aux");
+	if (IS_ERR(parent))
+		return PTR_ERR(parent);
+
+	usb20_phy_clk.parent = parent;
+	ret = clk_register(&usb20_phy_clk);
+	if (!ret)
+		clkdev_add(&usb20_phy_clk_lookup);
+
+	clk_put(parent);
+
+	return ret;
+}
+
+static int usb11_phy_clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	u32 val;
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	/* Set the USB 1.1 PHY clock mux based on the parent clock. */
+	if (parent == &usb20_phy_clk) {
+		val &= ~CFGCHIP2_USB1PHYCLKMUX;
+	} else if (parent == &usb_refclkin) {
+		val |= CFGCHIP2_USB1PHYCLKMUX;
+	} else {
+		pr_err("Bad parent on USB 1.1 PHY clock\n");
+		return -EINVAL;
+	}
+
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	return 0;
+}
+
+static struct clk usb11_phy_clk = {
+	.name		= "usb11_phy",
+	.set_parent	= usb11_phy_clk_set_parent,
+};
+
+static struct clk_lookup usb11_phy_clk_lookup =
+	CLK("da8xx-usb-phy", "usb11_phy", &usb11_phy_clk);
+
+/**
+ * da8xx_register_usb11_phy_clk - register USB1PHYCLKMUX clock
+ *
+ * @use_usb_refclkin: Selects the parent clock - either "usb_refclkin" if true
+ *	or "usb20_phy" if false.
+ */
+int __init da8xx_register_usb11_phy_clk(bool use_usb_refclkin)
+{
+	struct clk *parent;
+	int ret = 0;
+
+	if (use_usb_refclkin)
+		parent = clk_get(NULL, "usb_refclkin");
+	else
+		parent = clk_get(&da8xx_usb_phy.dev, "usb20_phy");
+	if (IS_ERR(parent))
+		return PTR_ERR(parent);
+
+	usb11_phy_clk.parent = parent;
+	ret = clk_register(&usb11_phy_clk);
+	if (!ret)
+		clkdev_add(&usb11_phy_clk_lookup);
+
+	clk_put(parent);
+
+	return ret;
+}
-- 
2.7.4

Re: [PATCH v8 2/3] ARM: davinci: da8xx: add usb phy clocks

[Sekhar Nori]

On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
> Up to this point, the USB phy clock configuration was handled manually in
> the board files and in the usb drivers. This adds proper clocks so that
> the usb drivers can use clk_get and clk_enable and not have to worry about
> the details. Also, the related code is removed from the board files and
> replaced with the new clock registration functions.
> 
> This also removes the #if IS_ENABLED(CONFIG_USB_MUSB_HDRC) around the musb
> declaration and renames the musb platform device so that we can reference
> it from the usb20 clock even if the musb device is not used.
> 
> Signed-off-by: David Lechner <david@lechnology.com>
> Signed-off-by: Axel Haslam <ahaslam@baylibre.com>

Applied to v4.10/soc

Thanks,
Sekhar

[PATCH v8 2/3] ARM: davinci: da8xx: add usb phy clocks

[Sekhar Nori]

On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
> Up to this point, the USB phy clock configuration was handled manually in
> the board files and in the usb drivers. This adds proper clocks so that
> the usb drivers can use clk_get and clk_enable and not have to worry about
> the details. Also, the related code is removed from the board files and
> replaced with the new clock registration functions.
> 
> This also removes the #if IS_ENABLED(CONFIG_USB_MUSB_HDRC) around the musb
> declaration and renames the musb platform device so that we can reference
> it from the usb20 clock even if the musb device is not used.
> 
> Signed-off-by: David Lechner <david@lechnology.com>
> Signed-off-by: Axel Haslam <ahaslam@baylibre.com>

Applied to v4.10/soc

Thanks,
Sekhar

Re: [PATCH v8 2/3] ARM: davinci: da8xx: add usb phy clocks

[Sekhar Nori]

On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
> Up to this point, the USB phy clock configuration was handled manually in
> the board files and in the usb drivers. This adds proper clocks so that
> the usb drivers can use clk_get and clk_enable and not have to worry about
> the details. Also, the related code is removed from the board files and
> replaced with the new clock registration functions.
> 
> This also removes the #if IS_ENABLED(CONFIG_USB_MUSB_HDRC) around the musb
> declaration and renames the musb platform device so that we can reference
> it from the usb20 clock even if the musb device is not used.
> 
> Signed-off-by: David Lechner <david@lechnology.com>
> Signed-off-by: Axel Haslam <ahaslam@baylibre.com>

Applied to v4.10/soc

Thanks,
Sekhar

[PATCH v8 3/3] ARM: davinci: da8xx: register USB PHY clocks in the DT file

[David Lechner]

From: Axel Haslam <ahaslam@baylibre.com>

The usb20_phy clock needs to be registered for the driver to be able
to get and enable a clock. Currently the usb phy clocks are registered
form board files, which will not be called during a device tree based
boot.

To be able to probe correctly usb form a device tree boot, register
the usb phy clocks form the DT specific init.

Unfourtunatly, davinci does not have proper clock support on device tree
yet, so by registering the clock form de DT specific file we are
forced to hardcode the parent clock, and cannot select refclkin as
parent for any of the phy clocks of the da850 family.

As none of the current da850 based boards currently in mainline use
refclkin as source. I guess we can live with this limitation until clocks
are correctly represented through CCF/device tree.

Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
[Added error checking]
Signed-off-by: David Lechner <david@lechnology.com>
---
 arch/arm/mach-davinci/da8xx-dt.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
index 20fa842..230c151 100644
--- a/arch/arm/mach-davinci/da8xx-dt.c
+++ b/arch/arm/mach-davinci/da8xx-dt.c
@@ -49,6 +49,17 @@ static struct of_dev_auxdata da850_auxdata_lookup[] __initdata = {
 
 static void __init da850_init_machine(void)
 {
+	int ret;
+
+	ret = da8xx_register_usb20_phy_clk(false);
+	if (ret)
+		pr_warn("%s: registering USB 2.0 PHY clock failed: %d",
+			__func__, ret);
+	ret = da8xx_register_usb11_phy_clk(false);
+	if (ret)
+		pr_warn("%s: registering USB 1.1 PHY clock failed: %d",
+			__func__, ret);
+
 	of_platform_default_populate(NULL, da850_auxdata_lookup, NULL);
 }
 
-- 
2.7.4

[PATCH v8 3/3] ARM: davinci: da8xx: register USB PHY clocks in the DT file

[David Lechner]

From: Axel Haslam <ahaslam@baylibre.com>

The usb20_phy clock needs to be registered for the driver to be able
to get and enable a clock. Currently the usb phy clocks are registered
form board files, which will not be called during a device tree based
boot.

To be able to probe correctly usb form a device tree boot, register
the usb phy clocks form the DT specific init.

Unfourtunatly, davinci does not have proper clock support on device tree
yet, so by registering the clock form de DT specific file we are
forced to hardcode the parent clock, and cannot select refclkin as
parent for any of the phy clocks of the da850 family.

As none of the current da850 based boards currently in mainline use
refclkin as source. I guess we can live with this limitation until clocks
are correctly represented through CCF/device tree.

Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
[Added error checking]
Signed-off-by: David Lechner <david@lechnology.com>
---
 arch/arm/mach-davinci/da8xx-dt.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
index 20fa842..230c151 100644
--- a/arch/arm/mach-davinci/da8xx-dt.c
+++ b/arch/arm/mach-davinci/da8xx-dt.c
@@ -49,6 +49,17 @@ static struct of_dev_auxdata da850_auxdata_lookup[] __initdata = {
 
 static void __init da850_init_machine(void)
 {
+	int ret;
+
+	ret = da8xx_register_usb20_phy_clk(false);
+	if (ret)
+		pr_warn("%s: registering USB 2.0 PHY clock failed: %d",
+			__func__, ret);
+	ret = da8xx_register_usb11_phy_clk(false);
+	if (ret)
+		pr_warn("%s: registering USB 1.1 PHY clock failed: %d",
+			__func__, ret);
+
 	of_platform_default_populate(NULL, da850_auxdata_lookup, NULL);
 }
 
-- 
2.7.4

[PATCH v8 3/3] ARM: davinci: da8xx: register USB PHY clocks in the DT file

[David Lechner]

From: Axel Haslam <ahaslam@baylibre.com>

The usb20_phy clock needs to be registered for the driver to be able
to get and enable a clock. Currently the usb phy clocks are registered
form board files, which will not be called during a device tree based
boot.

To be able to probe correctly usb form a device tree boot, register
the usb phy clocks form the DT specific init.

Unfourtunatly, davinci does not have proper clock support on device tree
yet, so by registering the clock form de DT specific file we are
forced to hardcode the parent clock, and cannot select refclkin as
parent for any of the phy clocks of the da850 family.

As none of the current da850 based boards currently in mainline use
refclkin as source. I guess we can live with this limitation until clocks
are correctly represented through CCF/device tree.

Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
[Added error checking]
Signed-off-by: David Lechner <david@lechnology.com>
---
 arch/arm/mach-davinci/da8xx-dt.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
index 20fa842..230c151 100644
--- a/arch/arm/mach-davinci/da8xx-dt.c
+++ b/arch/arm/mach-davinci/da8xx-dt.c
@@ -49,6 +49,17 @@ static struct of_dev_auxdata da850_auxdata_lookup[] __initdata = {
 
 static void __init da850_init_machine(void)
 {
+	int ret;
+
+	ret = da8xx_register_usb20_phy_clk(false);
+	if (ret)
+		pr_warn("%s: registering USB 2.0 PHY clock failed: %d",
+			__func__, ret);
+	ret = da8xx_register_usb11_phy_clk(false);
+	if (ret)
+		pr_warn("%s: registering USB 1.1 PHY clock failed: %d",
+			__func__, ret);
+
 	of_platform_default_populate(NULL, da850_auxdata_lookup, NULL);
 }
 
-- 
2.7.4

Re: [PATCH v8 3/3] ARM: davinci: da8xx: register USB PHY clocks in the DT file

[Sekhar Nori]

On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
> From: Axel Haslam <ahaslam@baylibre.com>
> 
> The usb20_phy clock needs to be registered for the driver to be able
> to get and enable a clock. Currently the usb phy clocks are registered
> form board files, which will not be called during a device tree based
> boot.
> 
> To be able to probe correctly usb form a device tree boot, register
> the usb phy clocks form the DT specific init.
> 
> Unfourtunatly, davinci does not have proper clock support on device tree
> yet, so by registering the clock form de DT specific file we are
> forced to hardcode the parent clock, and cannot select refclkin as
> parent for any of the phy clocks of the da850 family.
> 
> As none of the current da850 based boards currently in mainline use
> refclkin as source. I guess we can live with this limitation until clocks
> are correctly represented through CCF/device tree.
> 
> Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
> [Added error checking]
> Signed-off-by: David Lechner <david@lechnology.com>

Applied to v4.10/soc with some typo fixes.

s/form/from
s/Unfourtunatly/Unfortunately
s/de/the

Thanks,
Sekhar

[PATCH v8 3/3] ARM: davinci: da8xx: register USB PHY clocks in the DT file

[Sekhar Nori]

On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
> From: Axel Haslam <ahaslam@baylibre.com>
> 
> The usb20_phy clock needs to be registered for the driver to be able
> to get and enable a clock. Currently the usb phy clocks are registered
> form board files, which will not be called during a device tree based
> boot.
> 
> To be able to probe correctly usb form a device tree boot, register
> the usb phy clocks form the DT specific init.
> 
> Unfourtunatly, davinci does not have proper clock support on device tree
> yet, so by registering the clock form de DT specific file we are
> forced to hardcode the parent clock, and cannot select refclkin as
> parent for any of the phy clocks of the da850 family.
> 
> As none of the current da850 based boards currently in mainline use
> refclkin as source. I guess we can live with this limitation until clocks
> are correctly represented through CCF/device tree.
> 
> Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
> [Added error checking]
> Signed-off-by: David Lechner <david@lechnology.com>

Applied to v4.10/soc with some typo fixes.

s/form/from
s/Unfourtunatly/Unfortunately
s/de/the

Thanks,
Sekhar

Re: [PATCH v8 3/3] ARM: davinci: da8xx: register USB PHY clocks in the DT file

[Sekhar Nori]

On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
> From: Axel Haslam <ahaslam-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
> 
> The usb20_phy clock needs to be registered for the driver to be able
> to get and enable a clock. Currently the usb phy clocks are registered
> form board files, which will not be called during a device tree based
> boot.
> 
> To be able to probe correctly usb form a device tree boot, register
> the usb phy clocks form the DT specific init.
> 
> Unfourtunatly, davinci does not have proper clock support on device tree
> yet, so by registering the clock form de DT specific file we are
> forced to hardcode the parent clock, and cannot select refclkin as
> parent for any of the phy clocks of the da850 family.
> 
> As none of the current da850 based boards currently in mainline use
> refclkin as source. I guess we can live with this limitation until clocks
> are correctly represented through CCF/device tree.
> 
> Signed-off-by: Axel Haslam <ahaslam-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
> [Added error checking]
> Signed-off-by: David Lechner <david-nq/r/kbU++upp/zk7JDF2g@public.gmane.org>

Applied to v4.10/soc with some typo fixes.

s/form/from
s/Unfourtunatly/Unfortunately
s/de/the

Thanks,
Sekhar
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html