From: Anup Patel <anup.patel@broadcom.com> To: Rob Herring <robh+dt@kernel.org>, Mark Rutland <mark.rutland@arm.com>, Michael Turquette <mturquette@baylibre.com>, Stephen Boyd <sboyd@codeaurora.org> Cc: Catalin Marinas <catalin.marinas@arm.com>, Will Deacon <will.deacon@arm.com>, Ray Jui <rjui@broadcom.com>, Scott Branden <sbranden@broadcom.com>, Jon Mason <jonmason@broadcom.com>, Florian Fainelli <f.fainelli@gmail.com>, Oza Pawandeep <oza.oza@broadcom.com>, Srinath Mannam <srinath.mannam@broadcom.com>, Pramod Kumar <pramod.kumar@broadcom.com>, Sandeep Tripathy <sandeep.tripathy@broadcom.com>, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org, linux-arm-kernel@lists.infradead.org, bcm-kernel-feedback-list@broadcom.com Subject: [PATCH v6 09/11] arm64: dts: Add I2C DT nodes for Stingray SoC Date: Fri, 2 Jun 2017 12:04:33 +0530 [thread overview] Message-ID: <1496385275-6899-10-git-send-email-anup.patel@broadcom.com> (raw) In-Reply-To: <1496385275-6899-1-git-send-email-anup.patel@broadcom.com> From: Oza Pawandeep <oza.oza@broadcom.com> This patch adds I2C DT nodes on Stingray SoC. Signed-off-by: Oza Pawandeep <oza.oza@broadcom.com> Reviewed-by: Vikram Prakash <vikram.prakash@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> --- .../boot/dts/broadcom/stingray/bcm958742-base.dtsi | 22 ++++++++++++++++++++++ .../arm64/boot/dts/broadcom/stingray/stingray.dtsi | 20 ++++++++++++++++++++ 2 files changed, 42 insertions(+) diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi index aad45a2..ff59a26 100644 --- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi +++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi @@ -54,6 +54,28 @@ status = "okay"; }; +&i2c0 { + status = "okay"; + + pca9505: pca9505@20 { + compatible = "nxp,pca9505"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; +}; + +&i2c1 { + status = "okay"; + + pcf8574: pcf8574@20 { + compatible = "nxp,pcf8574a"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x27>; + }; +}; + &nand { status = "ok"; nandcs@0 { diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi index e91debe..91ba61e 100644 --- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi +++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi @@ -269,6 +269,16 @@ #include "stingray-pinctrl.dtsi" + i2c0: i2c@000b0000 { + compatible = "brcm,iproc-i2c"; + reg = <0x000b0000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 177 IRQ_TYPE_NONE>; + clock-frequency = <100000>; + status = "disabled"; + }; + gpio_hsls: gpio@000d0000 { compatible = "brcm,iproc-gpio"; reg = <0x000d0000 0x864>; @@ -295,6 +305,16 @@ <&pinmux 151 91 4>; }; + i2c1: i2c@000e0000 { + compatible = "brcm,iproc-i2c"; + reg = <0x000e0000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 178 IRQ_TYPE_NONE>; + clock-frequency = <100000>; + status = "disabled"; + }; + uart0: uart@00100000 { device_type = "serial"; compatible = "snps,dw-apb-uart"; -- 2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: anup.patel@broadcom.com (Anup Patel) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v6 09/11] arm64: dts: Add I2C DT nodes for Stingray SoC Date: Fri, 2 Jun 2017 12:04:33 +0530 [thread overview] Message-ID: <1496385275-6899-10-git-send-email-anup.patel@broadcom.com> (raw) In-Reply-To: <1496385275-6899-1-git-send-email-anup.patel@broadcom.com> From: Oza Pawandeep <oza.oza@broadcom.com> This patch adds I2C DT nodes on Stingray SoC. Signed-off-by: Oza Pawandeep <oza.oza@broadcom.com> Reviewed-by: Vikram Prakash <vikram.prakash@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> --- .../boot/dts/broadcom/stingray/bcm958742-base.dtsi | 22 ++++++++++++++++++++++ .../arm64/boot/dts/broadcom/stingray/stingray.dtsi | 20 ++++++++++++++++++++ 2 files changed, 42 insertions(+) diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi index aad45a2..ff59a26 100644 --- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi +++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi @@ -54,6 +54,28 @@ status = "okay"; }; +&i2c0 { + status = "okay"; + + pca9505: pca9505 at 20 { + compatible = "nxp,pca9505"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; +}; + +&i2c1 { + status = "okay"; + + pcf8574: pcf8574 at 20 { + compatible = "nxp,pcf8574a"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x27>; + }; +}; + &nand { status = "ok"; nandcs at 0 { diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi index e91debe..91ba61e 100644 --- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi +++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi @@ -269,6 +269,16 @@ #include "stingray-pinctrl.dtsi" + i2c0: i2c at 000b0000 { + compatible = "brcm,iproc-i2c"; + reg = <0x000b0000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 177 IRQ_TYPE_NONE>; + clock-frequency = <100000>; + status = "disabled"; + }; + gpio_hsls: gpio at 000d0000 { compatible = "brcm,iproc-gpio"; reg = <0x000d0000 0x864>; @@ -295,6 +305,16 @@ <&pinmux 151 91 4>; }; + i2c1: i2c at 000e0000 { + compatible = "brcm,iproc-i2c"; + reg = <0x000e0000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 178 IRQ_TYPE_NONE>; + clock-frequency = <100000>; + status = "disabled"; + }; + uart0: uart at 00100000 { device_type = "serial"; compatible = "snps,dw-apb-uart"; -- 2.7.4
next prev parent reply other threads:[~2017-06-02 6:36 UTC|newest] Thread overview: 41+ messages / expand[flat|nested] mbox.gz Atom feed top 2017-06-02 6:34 [PATCH v6 00/11] Broadcom Stingray SOC Initial Support Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 6:34 ` [PATCH v6 01/11] dt-bindings: bcm: Add Broadcom Stingray bindings document Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 6:34 ` [PATCH v6 02/11] dt-bindings: clk: Extend binding doc for Stingray SOC Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 6:34 ` [PATCH v6 03/11] clk: bcm: Add clocks " Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 22:10 ` Stephen Boyd 2017-06-02 22:10 ` Stephen Boyd 2017-06-06 4:21 ` Anup Patel 2017-06-06 4:21 ` Anup Patel 2017-06-02 6:34 ` [PATCH v6 04/11] arm64: dts: Initial DTS files for Broadcom " Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 6:34 ` [PATCH v6 05/11] arm64: dts: Add clock DT nodes for " Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 6:34 ` [PATCH v6 06/11] arm64: dts: Add NAND " Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 6:34 ` [PATCH v6 07/11] arm64: dts: Add pinctrl " Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 6:34 ` [PATCH v6 08/11] arm64: dts: Add GPIO " Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 6:34 ` Anup Patel [this message] 2017-06-02 6:34 ` [PATCH v6 09/11] arm64: dts: Add I2C DT nodes for Stingray SoC Anup Patel 2017-06-02 6:34 ` [PATCH v6 10/11] arm64: dts: Add PL022, PL330 and SP805 DT nodes for Stingray Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-02 6:34 ` [PATCH v6 11/11] arm64: dts: Add PWM and SDHCI DT nodes for Stingray SOC Anup Patel 2017-06-02 6:34 ` Anup Patel 2017-06-05 16:51 ` [PATCH v6 00/11] Broadcom Stingray SOC Initial Support Florian Fainelli 2017-06-05 16:51 ` Florian Fainelli 2017-06-06 2:08 ` Florian Fainelli 2017-06-06 2:08 ` Florian Fainelli 2017-06-06 3:20 ` Anup Patel 2017-06-06 3:20 ` Anup Patel 2017-06-06 22:30 ` Stephen Boyd 2017-06-06 22:30 ` Stephen Boyd 2017-06-06 22:30 ` Stephen Boyd 2017-06-20 0:28 ` Florian Fainelli 2017-06-20 0:28 ` Florian Fainelli
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1496385275-6899-10-git-send-email-anup.patel@broadcom.com \ --to=anup.patel@broadcom.com \ --cc=bcm-kernel-feedback-list@broadcom.com \ --cc=catalin.marinas@arm.com \ --cc=devicetree@vger.kernel.org \ --cc=f.fainelli@gmail.com \ --cc=jonmason@broadcom.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-clk@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=mark.rutland@arm.com \ --cc=mturquette@baylibre.com \ --cc=oza.oza@broadcom.com \ --cc=pramod.kumar@broadcom.com \ --cc=rjui@broadcom.com \ --cc=robh+dt@kernel.org \ --cc=sandeep.tripathy@broadcom.com \ --cc=sboyd@codeaurora.org \ --cc=sbranden@broadcom.com \ --cc=srinath.mannam@broadcom.com \ --cc=will.deacon@arm.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.