* [PATCH v2 0/6] ARM: Add Variscite DART-MX6 SoM and Carrier-board support
@ 2017-11-22 11:02 ` Neil Armstrong
0 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: linux-arm-kernel
This patchset adds support for the Variscite DART-MX6 SoM with :
- i.MX6 Quad or Dual Lite SoC
- 1Gb/2Gb LPDDR2
- 4-64 GB eMMC
- Camera Interface
- HDMI+CEC interface
- LVDS / DSI / Parallel RGB interfaces
- Ethernet RGMII interface
- On-SoM Wi-Fi/Bluetooth with WiLink wl1835 SDIO Module
- SD/MMC/SDIO interface
- USB Host + USB OTG interface
- I2C interfaces
- SPI interfaces
- PCI-Express 2.0 interface
- on-SoM Audio Codec with HP/Line-In interfaces + DMIC interface
- Digital Audio interface
- S/PDIF interface
And the Carrier-Board with the following :
- LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
- HDMI Connector
- USB Host + USB OTG Connector
- 10/100/1000 Mbps Ethernet
- miniPCI-Express slot
- SD Card connector
- Audio Headphone/Line In jack connectors
- On-board DMIC
- CAN bus header
- SPI header
- Camera Interfaces header
- 4xButtons, 2xLeds
- OnBoard RTC with Coin Backup battery socket
- RS232 Header + USB-Serial debug port
First patch contains a missing pinmux define used by the SoM.
Last patch contains configs used by the SoM DT like SERDEV or WL18XX support.
On-Board DMIC and Camera Interfaces are not handled yet.
Changes since v1 at [1]:
- Add lvds display vendor prefix and bindings
- fix all gpio phandle arguments with correct ACTIVE_XXX define
- drop pcie support
- drop custom operating points
- fix arm/pu/soc vin-supply instead of &cpu node override
- fix can pinmux value
- changed button node name
- add revied-by tags on first and last patches
[1] http://lkml.kernel.org/r/1511281705-30849-1-git-send-email-narmstrong at baylibre.com
Neil Armstrong (6):
ARM: dts: imx6qdl-pinfunc: Add missing
MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT
dt-bindings: Add vendor prefix for Solomon Goldentek Display
Corporation
devicetree/bindings: display: Add bindings for SGD GKTW70SDAE4SE Panel
ARM: dts: imx6qdl: Add Variscite DART-MX6 SoM support
ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support
ARM: configs: Add missing config for DART-MX6 SoM
.../bindings/display/panel/sgd,gktw70sdae4se.txt | 41 ++
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-pinfunc.h | 1 +
arch/arm/boot/dts/imx6q-pinfunc.h | 1 +
arch/arm/boot/dts/imx6q-var-dt6customboard.dts | 238 ++++++++++
arch/arm/boot/dts/imx6qdl-var-dart.dtsi | 501 +++++++++++++++++++++
arch/arm/configs/imx_v6_v7_defconfig | 6 +
8 files changed, 790 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
create mode 100644 arch/arm/boot/dts/imx6q-var-dt6customboard.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-var-dart.dtsi
--
2.7.4
^ permalink raw reply [flat|nested] 32+ messages in thread* [PATCH v2 1/6] ARM: dts: imx6qdl-pinfunc: Add missing MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT
2017-11-22 11:02 ` Neil Armstrong
@ 2017-11-22 11:02 ` Neil Armstrong
-1 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: Neil Armstrong, linux-arm-kernel, linux-kernel
Add missing pinmux entry for OSC32K_32K_OUT on pad ENET_RXD0 used by the
Variscite DART-MX6 SoM.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/boot/dts/imx6dl-pinfunc.h | 1 +
arch/arm/boot/dts/imx6q-pinfunc.h | 1 +
2 files changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/imx6dl-pinfunc.h b/arch/arm/boot/dts/imx6dl-pinfunc.h
index 0ead323..37e430a 100644
--- a/arch/arm/boot/dts/imx6dl-pinfunc.h
+++ b/arch/arm/boot/dts/imx6dl-pinfunc.h
@@ -668,6 +668,7 @@
#define MX6QDL_PAD_ENET_RX_ER__SPDIF_IN 0x1f4 0x5c4 0x8f0 0x3 0x1
#define MX6QDL_PAD_ENET_RX_ER__ENET_1588_EVENT2_OUT 0x1f4 0x5c4 0x000 0x4 0x0
#define MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x1f4 0x5c4 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT 0x1f8 0x5c8 0x000 0x0 0x0
#define MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1f8 0x5c8 0x818 0x1 0x0
#define MX6QDL_PAD_ENET_RXD0__ESAI_TX_HF_CLK 0x1f8 0x5c8 0x838 0x2 0x0
#define MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1f8 0x5c8 0x000 0x3 0x0
diff --git a/arch/arm/boot/dts/imx6q-pinfunc.h b/arch/arm/boot/dts/imx6q-pinfunc.h
index 9fc6120..cfb11d3 100644
--- a/arch/arm/boot/dts/imx6q-pinfunc.h
+++ b/arch/arm/boot/dts/imx6q-pinfunc.h
@@ -551,6 +551,7 @@
#define MX6QDL_PAD_ENET_RXD1__ESAI_TX_FS 0x1e0 0x4f4 0x860 0x2 0x0
#define MX6QDL_PAD_ENET_RXD1__ENET_1588_EVENT3_OUT 0x1e0 0x4f4 0x000 0x4 0x0
#define MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1e0 0x4f4 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT 0x1e4 0x4f8 0x000 0x0 0x0
#define MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1e4 0x4f8 0x848 0x1 0x1
#define MX6QDL_PAD_ENET_RXD0__ESAI_TX_HF_CLK 0x1e4 0x4f8 0x868 0x2 0x0
#define MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1e4 0x4f8 0x000 0x3 0x0
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread
* [PATCH v2 1/6] ARM: dts: imx6qdl-pinfunc: Add missing MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT
@ 2017-11-22 11:02 ` Neil Armstrong
0 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: linux-arm-kernel
Add missing pinmux entry for OSC32K_32K_OUT on pad ENET_RXD0 used by the
Variscite DART-MX6 SoM.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/boot/dts/imx6dl-pinfunc.h | 1 +
arch/arm/boot/dts/imx6q-pinfunc.h | 1 +
2 files changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/imx6dl-pinfunc.h b/arch/arm/boot/dts/imx6dl-pinfunc.h
index 0ead323..37e430a 100644
--- a/arch/arm/boot/dts/imx6dl-pinfunc.h
+++ b/arch/arm/boot/dts/imx6dl-pinfunc.h
@@ -668,6 +668,7 @@
#define MX6QDL_PAD_ENET_RX_ER__SPDIF_IN 0x1f4 0x5c4 0x8f0 0x3 0x1
#define MX6QDL_PAD_ENET_RX_ER__ENET_1588_EVENT2_OUT 0x1f4 0x5c4 0x000 0x4 0x0
#define MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x1f4 0x5c4 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT 0x1f8 0x5c8 0x000 0x0 0x0
#define MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1f8 0x5c8 0x818 0x1 0x0
#define MX6QDL_PAD_ENET_RXD0__ESAI_TX_HF_CLK 0x1f8 0x5c8 0x838 0x2 0x0
#define MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1f8 0x5c8 0x000 0x3 0x0
diff --git a/arch/arm/boot/dts/imx6q-pinfunc.h b/arch/arm/boot/dts/imx6q-pinfunc.h
index 9fc6120..cfb11d3 100644
--- a/arch/arm/boot/dts/imx6q-pinfunc.h
+++ b/arch/arm/boot/dts/imx6q-pinfunc.h
@@ -551,6 +551,7 @@
#define MX6QDL_PAD_ENET_RXD1__ESAI_TX_FS 0x1e0 0x4f4 0x860 0x2 0x0
#define MX6QDL_PAD_ENET_RXD1__ENET_1588_EVENT3_OUT 0x1e0 0x4f4 0x000 0x4 0x0
#define MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1e0 0x4f4 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT 0x1e4 0x4f8 0x000 0x0 0x0
#define MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1e4 0x4f8 0x848 0x1 0x1
#define MX6QDL_PAD_ENET_RXD0__ESAI_TX_HF_CLK 0x1e4 0x4f8 0x868 0x2 0x0
#define MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1e4 0x4f8 0x000 0x3 0x0
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread
* [PATCH v2 2/6] dt-bindings: Add vendor prefix for Solomon Goldentek Display Corporation
2017-11-22 11:02 ` Neil Armstrong
@ 2017-11-22 11:02 ` Neil Armstrong
-1 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: Neil Armstrong, linux-arm-kernel, linux-kernel, devicetree
Solomon Goldentek Display Corporation is a Taiwanese LCD/LCM manufacturer.
Company Site: http://www.goldentek.com.tw
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 0994bdd..b0d3bef 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -305,6 +305,7 @@ seagate Seagate Technology PLC
semtech Semtech Corporation
sensirion Sensirion AG
sff Small Form Factor Committee
+sgd Solomon Goldentek Display Corporation
sgx SGX Sensortech
sharp Sharp Corporation
shimafuji Shimafuji Electric, Inc.
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread
* [PATCH v2 2/6] dt-bindings: Add vendor prefix for Solomon Goldentek Display Corporation
@ 2017-11-22 11:02 ` Neil Armstrong
0 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: linux-arm-kernel
Solomon Goldentek Display Corporation is a Taiwanese LCD/LCM manufacturer.
Company Site: http://www.goldentek.com.tw
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 0994bdd..b0d3bef 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -305,6 +305,7 @@ seagate Seagate Technology PLC
semtech Semtech Corporation
sensirion Sensirion AG
sff Small Form Factor Committee
+sgd Solomon Goldentek Display Corporation
sgx SGX Sensortech
sharp Sharp Corporation
shimafuji Shimafuji Electric, Inc.
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread
* Re: [PATCH v2 2/6] dt-bindings: Add vendor prefix for Solomon Goldentek Display Corporation
@ 2017-11-26 18:58 ` Rob Herring
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring @ 2017-11-26 18:58 UTC (permalink / raw)
To: Neil Armstrong
Cc: shawnguo, kernel, fabio.estevam, linux-arm-kernel, linux-kernel,
devicetree
On Wed, Nov 22, 2017 at 12:02:36PM +0100, Neil Armstrong wrote:
> Solomon Goldentek Display Corporation is a Taiwanese LCD/LCM manufacturer.
> Company Site: http://www.goldentek.com.tw
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
> 1 file changed, 1 insertion(+)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 2/6] dt-bindings: Add vendor prefix for Solomon Goldentek Display Corporation
@ 2017-11-26 18:58 ` Rob Herring
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring @ 2017-11-26 18:58 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Nov 22, 2017 at 12:02:36PM +0100, Neil Armstrong wrote:
> Solomon Goldentek Display Corporation is a Taiwanese LCD/LCM manufacturer.
> Company Site: http://www.goldentek.com.tw
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
> 1 file changed, 1 insertion(+)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v2 2/6] dt-bindings: Add vendor prefix for Solomon Goldentek Display Corporation
@ 2017-11-26 18:58 ` Rob Herring
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring @ 2017-11-26 18:58 UTC (permalink / raw)
To: Neil Armstrong
Cc: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
fabio.estevam-3arQi8VN3Tc,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA
On Wed, Nov 22, 2017 at 12:02:36PM +0100, Neil Armstrong wrote:
> Solomon Goldentek Display Corporation is a Taiwanese LCD/LCM manufacturer.
> Company Site: http://www.goldentek.com.tw
>
> Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
> ---
> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
> 1 file changed, 1 insertion(+)
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 3/6] devicetree/bindings: display: Add bindings for SGD GKTW70SDAE4SE Panel
2017-11-22 11:02 ` Neil Armstrong
@ 2017-11-22 11:02 ` Neil Armstrong
-1 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: Neil Armstrong, linux-arm-kernel, linux-kernel, devicetree
The GKTW70SDAE4SE is an LVDS display panel.
Their bindings are modelled on the the LVDS panel bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../bindings/display/panel/sgd,gktw70sdae4se.txt | 41 ++++++++++++++++++++++
1 file changed, 41 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
diff --git a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
new file mode 100644
index 0000000..d06644b
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
@@ -0,0 +1,41 @@
+Solomon Goldentek Display GKTW70SDAE4SE LVDS Display Panel
+==========================================================
+
+The GKTW70SDAE4SE is a 7" WVGA TFT-LCD display panel.
+
+These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt
+with the following device-specific properties.
+
+Required properties:
+
+- compatible: Shall contain "sgd,gktw70sdae4se" and "panel-lvds", in that order.
+
+Example
+-------
+
+panel {
+ compatible = "sgd,gktw70sdae4se", "panel-lvds";
+
+ width-mm = <153>;
+ height-mm = <86>;
+
+ data-mapping = "jeida-18";
+
+ panel-timing {
+ clock-frequency = <32000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <39>;
+ hfront-porch = <39>;
+ vback-porch = <29>;
+ vfront-porch = <13>;
+ hsync-len = <47>;
+ vsync-len = <2>;
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds_encoder>;
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 3/6] devicetree/bindings: display: Add bindings for SGD GKTW70SDAE4SE Panel
@ 2017-11-22 11:02 ` Neil Armstrong
0 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: linux-arm-kernel
The GKTW70SDAE4SE is an LVDS display panel.
Their bindings are modelled on the the LVDS panel bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../bindings/display/panel/sgd,gktw70sdae4se.txt | 41 ++++++++++++++++++++++
1 file changed, 41 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
diff --git a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
new file mode 100644
index 0000000..d06644b
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
@@ -0,0 +1,41 @@
+Solomon Goldentek Display GKTW70SDAE4SE LVDS Display Panel
+==========================================================
+
+The GKTW70SDAE4SE is a 7" WVGA TFT-LCD display panel.
+
+These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt
+with the following device-specific properties.
+
+Required properties:
+
+- compatible: Shall contain "sgd,gktw70sdae4se" and "panel-lvds", in that order.
+
+Example
+-------
+
+panel {
+ compatible = "sgd,gktw70sdae4se", "panel-lvds";
+
+ width-mm = <153>;
+ height-mm = <86>;
+
+ data-mapping = "jeida-18";
+
+ panel-timing {
+ clock-frequency = <32000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <39>;
+ hfront-porch = <39>;
+ vback-porch = <29>;
+ vfront-porch = <13>;
+ hsync-len = <47>;
+ vsync-len = <2>;
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds_encoder>;
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 3/6] devicetree/bindings: display: Add bindings for SGD GKTW70SDAE4SE Panel
@ 2017-11-26 19:00 ` Rob Herring
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring @ 2017-11-26 19:00 UTC (permalink / raw)
To: Neil Armstrong
Cc: shawnguo, kernel, fabio.estevam, devicetree, linux-kernel,
linux-arm-kernel
On Wed, Nov 22, 2017 at 12:02:37PM +0100, Neil Armstrong wrote:
> The GKTW70SDAE4SE is an LVDS display panel.
> Their bindings are modelled on the the LVDS panel bindings.
Be consistent with your subjects. "dt-bindings: "
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> .../bindings/display/panel/sgd,gktw70sdae4se.txt | 41 ++++++++++++++++++++++
> 1 file changed, 41 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
With that,
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 3/6] devicetree/bindings: display: Add bindings for SGD GKTW70SDAE4SE Panel
@ 2017-11-26 19:00 ` Rob Herring
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring @ 2017-11-26 19:00 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Nov 22, 2017 at 12:02:37PM +0100, Neil Armstrong wrote:
> The GKTW70SDAE4SE is an LVDS display panel.
> Their bindings are modelled on the the LVDS panel bindings.
Be consistent with your subjects. "dt-bindings: "
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> .../bindings/display/panel/sgd,gktw70sdae4se.txt | 41 ++++++++++++++++++++++
> 1 file changed, 41 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
With that,
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v2 3/6] devicetree/bindings: display: Add bindings for SGD GKTW70SDAE4SE Panel
@ 2017-11-26 19:00 ` Rob Herring
0 siblings, 0 replies; 32+ messages in thread
From: Rob Herring @ 2017-11-26 19:00 UTC (permalink / raw)
To: Neil Armstrong
Cc: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
fabio.estevam-3arQi8VN3Tc, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Wed, Nov 22, 2017 at 12:02:37PM +0100, Neil Armstrong wrote:
> The GKTW70SDAE4SE is an LVDS display panel.
> Their bindings are modelled on the the LVDS panel bindings.
Be consistent with your subjects. "dt-bindings: "
>
> Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
> ---
> .../bindings/display/panel/sgd,gktw70sdae4se.txt | 41 ++++++++++++++++++++++
> 1 file changed, 41 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
With that,
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 4/6] ARM: dts: imx6qdl: Add Variscite DART-MX6 SoM support
2017-11-22 11:02 ` Neil Armstrong
@ 2017-11-22 11:02 ` Neil Armstrong
-1 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: Neil Armstrong, linux-arm-kernel, linux-kernel
This patch adds support for the Variscite DART-MX6 SoM with :
- i.MX6 Quad or Dual Lite SoC
- 1Gb/2Gb LPDDR2
- 4-64 GB eMMC
- Camera Interface
- HDMI+CEC interface
- LVDS / DSI / Parallel RGB interfaces
- Ethernet RGMII interface
- On-SoM Wi-Fi/Bluetooth with WiLink wl1835 SDIO Module
- SD/MMC/SDIO interface
- USB Host + USB OTG interface
- I2C interfaces
- SPI interfaces
- PCI-Express 2.0 interface
- on-SoM Audio Codec with HP/Line-In interfaces + DMIC interface
- Digital Audio interface
- S/PDIF interface
Product website : http://www.variscite.com/products/system-on-module-som/cortex-a9/dart-mx6-cpu-freescale-imx6
Support is handled with a SoM-centric dtsi exporting the default interfaces
along the default pinmuxing to be enabled by the board dts file.
Only board-independent devices like WiFi, eMMC or PMIC are enabled in the dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/boot/dts/imx6qdl-var-dart.dtsi | 501 ++++++++++++++++++++++++++++++++
1 file changed, 501 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-var-dart.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-var-dart.dtsi b/arch/arm/boot/dts/imx6qdl-var-dart.dtsi
new file mode 100644
index 0000000..0dd806b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-var-dart.dtsi
@@ -0,0 +1,501 @@
+/*
+ * Support for Variscite DART-MX6 Module
+ *
+ * Copyright 2017 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_wl18xx_vmmc: regulator-wl18xx {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1807";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <70000>;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ ssi2 {
+ fsl,audmux-port = <1>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_SYN |
+ IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR |
+ IMX_AUDMUX_V2_PTCR_TCSEL(2))
+ IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ aud3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN
+ IMX_AUDMUX_V2_PDCR_RXDSEL(1)
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "disabled";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "disabled";
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "disabled";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ status = "disabled";
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmicec>;
+ status = "disabled";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "disabled";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ pmic@08 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+
+ codec: codec@1b {
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ #sound-dai-cells = <0>;
+ DRVDD-supply = <®_3p3v>;
+ AVDD-supply = <®_3p3v>;
+ IOVDD-supply = <®_3p3v>;
+ DVDD-supply = <®_3p3v>;
+ ai3x-ocmv = <0>;
+ gpio-reset = <&gpio5 5 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_audmux: audmux {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ /* Audio Clock */
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_bt: bt {
+ fsl,pins = <
+ /* Bluetooth enable */
+ MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b1
+ /* Bluetooth Slow Clock */
+ MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT 0x000b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
+ /* SPI1 CS0 */
+ MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x1b0b0
+ /* SPI1 CS1 */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
+ MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b0b0
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_hdmicec: hdmicecgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ /* PMIC INT */
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
+ MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ /* WL_EN */
+ MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x17071
+ /* WL_IRQ */
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x17071
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170B9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100B9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170B9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170B9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170B9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170B9
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170F9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100F9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170F9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170F9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170F9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170F9
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ >;
+ };
+};
+
+&pcie {
+ fsl,tx-swing-full = <103>;
+ fsl,tx-swing-low = <103>;
+ status = "disabled";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "disabled";
+};
+
+®_arm {
+ vin-supply = <&sw1a_reg>;
+};
+
+®_pu {
+ vin-supply = <&sw1c_reg>;
+};
+
+®_soc {
+ vin-supply = <&sw1c_reg>;
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2 &pinctrl_bt>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "ti,wl1835-st";
+ enable-gpios = <&gpio6 18 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ uart-has-rtscts;
+ status = "disabled";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "disabled";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <4>;
+ vmmc-supply = <®_wl18xx_vmmc>;
+ non-removable;
+ wakeup-source;
+ keep-power-in-suspend;
+ cap-power-off-card;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+ ref-clock-frequency = <38400000>;
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "disabled";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ non-removable;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
+
+&ssi2 {
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 4/6] ARM: dts: imx6qdl: Add Variscite DART-MX6 SoM support
@ 2017-11-22 11:02 ` Neil Armstrong
0 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds support for the Variscite DART-MX6 SoM with :
- i.MX6 Quad or Dual Lite SoC
- 1Gb/2Gb LPDDR2
- 4-64 GB eMMC
- Camera Interface
- HDMI+CEC interface
- LVDS / DSI / Parallel RGB interfaces
- Ethernet RGMII interface
- On-SoM Wi-Fi/Bluetooth with WiLink wl1835 SDIO Module
- SD/MMC/SDIO interface
- USB Host + USB OTG interface
- I2C interfaces
- SPI interfaces
- PCI-Express 2.0 interface
- on-SoM Audio Codec with HP/Line-In interfaces + DMIC interface
- Digital Audio interface
- S/PDIF interface
Product website : http://www.variscite.com/products/system-on-module-som/cortex-a9/dart-mx6-cpu-freescale-imx6
Support is handled with a SoM-centric dtsi exporting the default interfaces
along the default pinmuxing to be enabled by the board dts file.
Only board-independent devices like WiFi, eMMC or PMIC are enabled in the dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/boot/dts/imx6qdl-var-dart.dtsi | 501 ++++++++++++++++++++++++++++++++
1 file changed, 501 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-var-dart.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-var-dart.dtsi b/arch/arm/boot/dts/imx6qdl-var-dart.dtsi
new file mode 100644
index 0000000..0dd806b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-var-dart.dtsi
@@ -0,0 +1,501 @@
+/*
+ * Support for Variscite DART-MX6 Module
+ *
+ * Copyright 2017 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_wl18xx_vmmc: regulator-wl18xx {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1807";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <70000>;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ ssi2 {
+ fsl,audmux-port = <1>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_SYN |
+ IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR |
+ IMX_AUDMUX_V2_PTCR_TCSEL(2))
+ IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ aud3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN
+ IMX_AUDMUX_V2_PDCR_RXDSEL(1)
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "disabled";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "disabled";
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "disabled";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ status = "disabled";
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmicec>;
+ status = "disabled";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "disabled";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ pmic at 08 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+
+ codec: codec at 1b {
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ #sound-dai-cells = <0>;
+ DRVDD-supply = <®_3p3v>;
+ AVDD-supply = <®_3p3v>;
+ IOVDD-supply = <®_3p3v>;
+ DVDD-supply = <®_3p3v>;
+ ai3x-ocmv = <0>;
+ gpio-reset = <&gpio5 5 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_audmux: audmux {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ /* Audio Clock */
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_bt: bt {
+ fsl,pins = <
+ /* Bluetooth enable */
+ MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b1
+ /* Bluetooth Slow Clock */
+ MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT 0x000b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
+ /* SPI1 CS0 */
+ MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x1b0b0
+ /* SPI1 CS1 */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
+ MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b0b0
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_hdmicec: hdmicecgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ /* PMIC INT */
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
+ MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ /* WL_EN */
+ MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x17071
+ /* WL_IRQ */
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x17071
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170B9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100B9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170B9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170B9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170B9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170B9
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170F9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100F9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170F9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170F9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170F9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170F9
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ >;
+ };
+};
+
+&pcie {
+ fsl,tx-swing-full = <103>;
+ fsl,tx-swing-low = <103>;
+ status = "disabled";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "disabled";
+};
+
+®_arm {
+ vin-supply = <&sw1a_reg>;
+};
+
+®_pu {
+ vin-supply = <&sw1c_reg>;
+};
+
+®_soc {
+ vin-supply = <&sw1c_reg>;
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2 &pinctrl_bt>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "ti,wl1835-st";
+ enable-gpios = <&gpio6 18 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ uart-has-rtscts;
+ status = "disabled";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "disabled";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <4>;
+ vmmc-supply = <®_wl18xx_vmmc>;
+ non-removable;
+ wakeup-source;
+ keep-power-in-suspend;
+ cap-power-off-card;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ wlcore: wlcore at 2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+ ref-clock-frequency = <38400000>;
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "disabled";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ non-removable;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
+
+&ssi2 {
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 4/6] ARM: dts: imx6qdl: Add Variscite DART-MX6 SoM support
2017-11-22 11:02 ` Neil Armstrong
@ 2017-11-24 14:31 ` Fabio Estevam
-1 siblings, 0 replies; 32+ messages in thread
From: Fabio Estevam @ 2017-11-24 14:31 UTC (permalink / raw)
To: Neil Armstrong
Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-kernel, linux-arm-kernel
On Wed, Nov 22, 2017 at 9:02 AM, Neil Armstrong <narmstrong@baylibre.com> wrote:
> + reg_wl18xx_vmmc: regulator-wl18xx {
> + compatible = "regulator-fixed";
> + regulator-name = "vwl1807";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
Is this really GPIO_ACTIVE_HIGH?
If so, then a 'enable-active-high' property would be needed.
> +&hdmi {
No ddc-i2c-bus property?
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + /* PMIC INT */
> + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000
No 0x80000000 please. Use the real IOMUX value here instead.
> +&pcie {
> + fsl,tx-swing-full = <103>;
> + fsl,tx-swing-low = <103>;
> + status = "disabled";
No 'reset-gpio' property?
^ permalink raw reply [flat|nested] 32+ messages in thread* [PATCH v2 4/6] ARM: dts: imx6qdl: Add Variscite DART-MX6 SoM support
@ 2017-11-24 14:31 ` Fabio Estevam
0 siblings, 0 replies; 32+ messages in thread
From: Fabio Estevam @ 2017-11-24 14:31 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Nov 22, 2017 at 9:02 AM, Neil Armstrong <narmstrong@baylibre.com> wrote:
> + reg_wl18xx_vmmc: regulator-wl18xx {
> + compatible = "regulator-fixed";
> + regulator-name = "vwl1807";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
Is this really GPIO_ACTIVE_HIGH?
If so, then a 'enable-active-high' property would be needed.
> +&hdmi {
No ddc-i2c-bus property?
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + /* PMIC INT */
> + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000
No 0x80000000 please. Use the real IOMUX value here instead.
> +&pcie {
> + fsl,tx-swing-full = <103>;
> + fsl,tx-swing-low = <103>;
> + status = "disabled";
No 'reset-gpio' property?
^ permalink raw reply [flat|nested] 32+ messages in thread* Re: [PATCH v2 4/6] ARM: dts: imx6qdl: Add Variscite DART-MX6 SoM support
2017-11-24 14:31 ` Fabio Estevam
@ 2017-11-24 14:41 ` Neil Armstrong
-1 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-24 14:41 UTC (permalink / raw)
To: Fabio Estevam
Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-kernel, linux-arm-kernel
Hi Fabio,
On 24/11/2017 15:31, Fabio Estevam wrote:
> On Wed, Nov 22, 2017 at 9:02 AM, Neil Armstrong <narmstrong@baylibre.com> wrote:
>
>> + reg_wl18xx_vmmc: regulator-wl18xx {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vwl1807";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
>
> Is this really GPIO_ACTIVE_HIGH?
>
> If so, then a 'enable-active-high' property would be needed.
Indeed, it's quite redundant with the GPIO_ACTIVE_* flag, but whatever.
>
>> +&hdmi {
>
> No ddc-i2c-bus property?
It's in the board dts.
>
>> + pinctrl_pmic: pmicgrp {
>> + fsl,pins = <
>> + /* PMIC INT */
>> + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000
>
> No 0x80000000 please. Use the real IOMUX value here instead.
Ok
>
>> +&pcie {
>> + fsl,tx-swing-full = <103>;
>> + fsl,tx-swing-low = <103>;
>> + status = "disabled";
>
> No 'reset-gpio' property?
>
It will be in the board dts.
Neil
^ permalink raw reply [flat|nested] 32+ messages in thread* [PATCH v2 4/6] ARM: dts: imx6qdl: Add Variscite DART-MX6 SoM support
@ 2017-11-24 14:41 ` Neil Armstrong
0 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-24 14:41 UTC (permalink / raw)
To: linux-arm-kernel
Hi Fabio,
On 24/11/2017 15:31, Fabio Estevam wrote:
> On Wed, Nov 22, 2017 at 9:02 AM, Neil Armstrong <narmstrong@baylibre.com> wrote:
>
>> + reg_wl18xx_vmmc: regulator-wl18xx {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vwl1807";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
>
> Is this really GPIO_ACTIVE_HIGH?
>
> If so, then a 'enable-active-high' property would be needed.
Indeed, it's quite redundant with the GPIO_ACTIVE_* flag, but whatever.
>
>> +&hdmi {
>
> No ddc-i2c-bus property?
It's in the board dts.
>
>> + pinctrl_pmic: pmicgrp {
>> + fsl,pins = <
>> + /* PMIC INT */
>> + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000
>
> No 0x80000000 please. Use the real IOMUX value here instead.
Ok
>
>> +&pcie {
>> + fsl,tx-swing-full = <103>;
>> + fsl,tx-swing-low = <103>;
>> + status = "disabled";
>
> No 'reset-gpio' property?
>
It will be in the board dts.
Neil
^ permalink raw reply [flat|nested] 32+ messages in thread* Re: [PATCH v2 4/6] ARM: dts: imx6qdl: Add Variscite DART-MX6 SoM support
2017-11-24 14:41 ` Neil Armstrong
@ 2017-11-24 14:44 ` Fabio Estevam
-1 siblings, 0 replies; 32+ messages in thread
From: Fabio Estevam @ 2017-11-24 14:44 UTC (permalink / raw)
To: Neil Armstrong
Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-kernel, linux-arm-kernel
Hi Neil,
On Fri, Nov 24, 2017 at 12:41 PM, Neil Armstrong
<narmstrong@baylibre.com> wrote:
>>> +&hdmi {
>>
>> No ddc-i2c-bus property?
>
> It's in the board dts.
Yes, I saw it while reviewing the other patch.
Do different boards use different I2C ports for the HDMI EDID?
If not, then you could probably put it here instead.
>>> +&pcie {
>>> + fsl,tx-swing-full = <103>;
>>> + fsl,tx-swing-low = <103>;
>>> + status = "disabled";
>>
>> No 'reset-gpio' property?
>>
>
> It will be in the board dts.
Same here.
^ permalink raw reply [flat|nested] 32+ messages in thread* [PATCH v2 4/6] ARM: dts: imx6qdl: Add Variscite DART-MX6 SoM support
@ 2017-11-24 14:44 ` Fabio Estevam
0 siblings, 0 replies; 32+ messages in thread
From: Fabio Estevam @ 2017-11-24 14:44 UTC (permalink / raw)
To: linux-arm-kernel
Hi Neil,
On Fri, Nov 24, 2017 at 12:41 PM, Neil Armstrong
<narmstrong@baylibre.com> wrote:
>>> +&hdmi {
>>
>> No ddc-i2c-bus property?
>
> It's in the board dts.
Yes, I saw it while reviewing the other patch.
Do different boards use different I2C ports for the HDMI EDID?
If not, then you could probably put it here instead.
>>> +&pcie {
>>> + fsl,tx-swing-full = <103>;
>>> + fsl,tx-swing-low = <103>;
>>> + status = "disabled";
>>
>> No 'reset-gpio' property?
>>
>
> It will be in the board dts.
Same here.
^ permalink raw reply [flat|nested] 32+ messages in thread* Re: [PATCH v2 4/6] ARM: dts: imx6qdl: Add Variscite DART-MX6 SoM support
2017-11-24 14:44 ` Fabio Estevam
@ 2017-11-24 14:46 ` Neil Armstrong
-1 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-24 14:46 UTC (permalink / raw)
To: Fabio Estevam
Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-kernel, linux-arm-kernel
On 24/11/2017 15:44, Fabio Estevam wrote:
> Hi Neil,
>
> On Fri, Nov 24, 2017 at 12:41 PM, Neil Armstrong
> <narmstrong@baylibre.com> wrote:
>
>>>> +&hdmi {
>>>
>>> No ddc-i2c-bus property?
>>
>> It's in the board dts.
>
> Yes, I saw it while reviewing the other patch.
>
> Do different boards use different I2C ports for the HDMI EDID?
>
> If not, then you could probably put it here instead.
Not at my knowledge, but it's typically something routed on the carrier board.
Anyway I can set it here.
>
>>>> +&pcie {
>>>> + fsl,tx-swing-full = <103>;
>>>> + fsl,tx-swing-low = <103>;
>>>> + status = "disabled";
>>>
>>> No 'reset-gpio' property?
>>>
>>
>> It will be in the board dts.
>
> Same here.
>
Ok.
Neil
^ permalink raw reply [flat|nested] 32+ messages in thread* [PATCH v2 4/6] ARM: dts: imx6qdl: Add Variscite DART-MX6 SoM support
@ 2017-11-24 14:46 ` Neil Armstrong
0 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-24 14:46 UTC (permalink / raw)
To: linux-arm-kernel
On 24/11/2017 15:44, Fabio Estevam wrote:
> Hi Neil,
>
> On Fri, Nov 24, 2017 at 12:41 PM, Neil Armstrong
> <narmstrong@baylibre.com> wrote:
>
>>>> +&hdmi {
>>>
>>> No ddc-i2c-bus property?
>>
>> It's in the board dts.
>
> Yes, I saw it while reviewing the other patch.
>
> Do different boards use different I2C ports for the HDMI EDID?
>
> If not, then you could probably put it here instead.
Not at my knowledge, but it's typically something routed on the carrier board.
Anyway I can set it here.
>
>>>> +&pcie {
>>>> + fsl,tx-swing-full = <103>;
>>>> + fsl,tx-swing-low = <103>;
>>>> + status = "disabled";
>>>
>>> No 'reset-gpio' property?
>>>
>>
>> It will be in the board dts.
>
> Same here.
>
Ok.
Neil
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 5/6] ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support
2017-11-22 11:02 ` Neil Armstrong
@ 2017-11-22 11:02 ` Neil Armstrong
-1 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: Neil Armstrong, linux-arm-kernel, linux-kernel
This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
SoM Carrier-Board.
This Carrier-Board has the following :
- LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
- HDMI Connector
- USB Host + USB OTG Connector
- 10/100/1000 Mbps Ethernet
- miniPCI-Express slot
- SD Card connector
- Audio Headphone/Line In jack connectors
- On-board DMIC
- CAN bus header
- SPI header
- Camera Interfaces header
- 4xButtons, 2xLeds
- OnBoard RTC with Coin Backup battery socket
- RS232 Header + USB-Serial debug port
Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits
The board support is done with all on-board and header interfaces enabled.
7" LVDS Touchscreen is enabled by default along HDMI output.
Audio interface is supported with the "simple-card" bindings.
PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-var-dt6customboard.dts | 238 +++++++++++++++++++++++++
2 files changed, 239 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-var-dt6customboard.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d0381e9..148ff15 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -470,6 +470,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-tx6q-11x0-mb7.dtb \
imx6q-udoo.dtb \
imx6q-utilite-pro.dtb \
+ imx6q-var-dt6customboard.dtb \
imx6q-wandboard.dtb \
imx6q-wandboard-revb1.dtb \
imx6q-wandboard-revd1.dtb \
diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
new file mode 100644
index 0000000..de01755
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
@@ -0,0 +1,238 @@
+/*
+ * Support for Variscite DART-MX6 Carrier-board
+ *
+ * Copyright 2017 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-var-dart.dtsi"
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+ model = "Variscite DART-MX6 Carrier-board";
+ compatible = "variscite,dt6customboard", "fsl,imx6q";
+
+ backlight_lvds: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 50000>;
+ brightness-levels = <0 4 8 16 32 64 128 248>;
+ default-brightness-level = <7>;
+ status = "okay";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ back {
+ gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_BACK>;
+ label = "Key Back";
+ linux,input-type = <1>;
+ debounce-interval = <100>;
+ gpio-key,wakeup;
+ };
+
+ home {
+ gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOME>;
+ label = "Key Home";
+ linux,input-type = <1>;
+ debounce-interval = <100>;
+ gpio-key,wakeup;
+ };
+
+ menu {
+ gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_MENU>;
+ label = "Key Menu";
+ linux,input-type = <1>;
+ debounce-interval = <100>;
+ gpio-key,wakeup;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led1 {
+ gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led2 {
+ gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ panel1: lvds-panel {
+ compatible = "sgd,gktw70sdae4se", "panel-lvds";
+ backlight = <&backlight_lvds>;
+
+ width-mm = <153>;
+ height-mm = <86>;
+
+ label = "gktw70sdae4se";
+
+ data-mapping = "jeida-18";
+
+ panel-timing {
+ clock-frequency = <32000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <39>;
+ hfront-porch = <39>;
+ vback-porch = <29>;
+ vfront-porch = <13>;
+ hsync-len = <47>;
+ vsync-len = <2>;
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds1_out>;
+ };
+ };
+ };
+
+ reg_usb_h1_vbus: regulator-usbh1vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb_otg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "dt6-customboard-audio";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&sound_codec>;
+ simple-audio-card,frame-master = <&sound_codec>;
+ simple-audio-card,widgets = "Headphone", "Headphone Jack",
+ "Line", "Line In";
+ simple-audio-card,routing = "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In";
+
+ sound_cpu: simple-audio-card,cpu {
+ sound-dai = <&ssi2>;
+ };
+
+ sound_codec: simple-audio-card,codec {
+ sound-dai = <&codec>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ };
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>,
+ <&gpio4 10 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&fec {
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c1>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ status = "okay";
+
+ touchscreen@38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ };
+
+ rtc@68 {
+ compatible = "isil,isl12057";
+ reg = <0x68>;
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@1 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds1_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ dr_mode = "otg";
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ status = "okay";
+};
+
+&usdhc2 {
+ cd-gpios = <&gpio1 6 1>;
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2 5/6] ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support
@ 2017-11-22 11:02 ` Neil Armstrong
0 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
SoM Carrier-Board.
This Carrier-Board has the following :
- LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
- HDMI Connector
- USB Host + USB OTG Connector
- 10/100/1000 Mbps Ethernet
- miniPCI-Express slot
- SD Card connector
- Audio Headphone/Line In jack connectors
- On-board DMIC
- CAN bus header
- SPI header
- Camera Interfaces header
- 4xButtons, 2xLeds
- OnBoard RTC with Coin Backup battery socket
- RS232 Header + USB-Serial debug port
Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits
The board support is done with all on-board and header interfaces enabled.
7" LVDS Touchscreen is enabled by default along HDMI output.
Audio interface is supported with the "simple-card" bindings.
PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-var-dt6customboard.dts | 238 +++++++++++++++++++++++++
2 files changed, 239 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-var-dt6customboard.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d0381e9..148ff15 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -470,6 +470,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-tx6q-11x0-mb7.dtb \
imx6q-udoo.dtb \
imx6q-utilite-pro.dtb \
+ imx6q-var-dt6customboard.dtb \
imx6q-wandboard.dtb \
imx6q-wandboard-revb1.dtb \
imx6q-wandboard-revd1.dtb \
diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
new file mode 100644
index 0000000..de01755
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
@@ -0,0 +1,238 @@
+/*
+ * Support for Variscite DART-MX6 Carrier-board
+ *
+ * Copyright 2017 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-var-dart.dtsi"
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+ model = "Variscite DART-MX6 Carrier-board";
+ compatible = "variscite,dt6customboard", "fsl,imx6q";
+
+ backlight_lvds: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 50000>;
+ brightness-levels = <0 4 8 16 32 64 128 248>;
+ default-brightness-level = <7>;
+ status = "okay";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ back {
+ gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_BACK>;
+ label = "Key Back";
+ linux,input-type = <1>;
+ debounce-interval = <100>;
+ gpio-key,wakeup;
+ };
+
+ home {
+ gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOME>;
+ label = "Key Home";
+ linux,input-type = <1>;
+ debounce-interval = <100>;
+ gpio-key,wakeup;
+ };
+
+ menu {
+ gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_MENU>;
+ label = "Key Menu";
+ linux,input-type = <1>;
+ debounce-interval = <100>;
+ gpio-key,wakeup;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led1 {
+ gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led2 {
+ gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ panel1: lvds-panel {
+ compatible = "sgd,gktw70sdae4se", "panel-lvds";
+ backlight = <&backlight_lvds>;
+
+ width-mm = <153>;
+ height-mm = <86>;
+
+ label = "gktw70sdae4se";
+
+ data-mapping = "jeida-18";
+
+ panel-timing {
+ clock-frequency = <32000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <39>;
+ hfront-porch = <39>;
+ vback-porch = <29>;
+ vfront-porch = <13>;
+ hsync-len = <47>;
+ vsync-len = <2>;
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds1_out>;
+ };
+ };
+ };
+
+ reg_usb_h1_vbus: regulator-usbh1vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb_otg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "dt6-customboard-audio";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&sound_codec>;
+ simple-audio-card,frame-master = <&sound_codec>;
+ simple-audio-card,widgets = "Headphone", "Headphone Jack",
+ "Line", "Line In";
+ simple-audio-card,routing = "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In";
+
+ sound_cpu: simple-audio-card,cpu {
+ sound-dai = <&ssi2>;
+ };
+
+ sound_codec: simple-audio-card,codec {
+ sound-dai = <&codec>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ };
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>,
+ <&gpio4 10 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&fec {
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c1>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ status = "okay";
+
+ touchscreen at 38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ };
+
+ rtc at 68 {
+ compatible = "isil,isl12057";
+ reg = <0x68>;
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel at 1 {
+ status = "okay";
+
+ port at 4 {
+ reg = <4>;
+
+ lvds1_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ dr_mode = "otg";
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ status = "okay";
+};
+
+&usdhc2 {
+ cd-gpios = <&gpio1 6 1>;
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2 5/6] ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support
2017-11-22 11:02 ` Neil Armstrong
@ 2017-11-24 14:33 ` Fabio Estevam
-1 siblings, 0 replies; 32+ messages in thread
From: Fabio Estevam @ 2017-11-24 14:33 UTC (permalink / raw)
To: Neil Armstrong
Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-kernel, linux-arm-kernel
On Wed, Nov 22, 2017 at 9:02 AM, Neil Armstrong <narmstrong@baylibre.com> wrote:
> This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
> SoM Carrier-Board.
>
> This Carrier-Board has the following :
> - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
> - HDMI Connector
> - USB Host + USB OTG Connector
> - 10/100/1000 Mbps Ethernet
> - miniPCI-Express slot
> - SD Card connector
> - Audio Headphone/Line In jack connectors
> - On-board DMIC
> - CAN bus header
> - SPI header
> - Camera Interfaces header
> - 4xButtons, 2xLeds
> - OnBoard RTC with Coin Backup battery socket
> - RS232 Header + USB-Serial debug port
>
> Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits
>
> The board support is done with all on-board and header interfaces enabled.
> 7" LVDS Touchscreen is enabled by default along HDMI output.
> Audio interface is supported with the "simple-card" bindings.
>
> PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-var-dt6customboard.dts | 238 +++++++++++++++++++++++++
> 2 files changed, 239 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-var-dt6customboard.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index d0381e9..148ff15 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -470,6 +470,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-tx6q-11x0-mb7.dtb \
> imx6q-udoo.dtb \
> imx6q-utilite-pro.dtb \
> + imx6q-var-dt6customboard.dtb \
> imx6q-wandboard.dtb \
> imx6q-wandboard-revb1.dtb \
> imx6q-wandboard-revd1.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
> new file mode 100644
> index 0000000..de01755
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
> @@ -0,0 +1,238 @@
> +/*
> + * Support for Variscite DART-MX6 Carrier-board
> + *
> + * Copyright 2017 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + *
> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +#include "imx6qdl-var-dart.dtsi"
> +#include <dt-bindings/input/linux-event-codes.h>
> +
> +/ {
> + model = "Variscite DART-MX6 Carrier-board";
> + compatible = "variscite,dt6customboard", "fsl,imx6q";
> +
> + backlight_lvds: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 50000>;
> + brightness-levels = <0 4 8 16 32 64 128 248>;
> + default-brightness-level = <7>;
> + status = "okay";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + autorepeat;
> +
> + back {
> + gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_BACK>;
> + label = "Key Back";
> + linux,input-type = <1>;
> + debounce-interval = <100>;
> + gpio-key,wakeup;
> + };
> +
> + home {
> + gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_HOME>;
> + label = "Key Home";
> + linux,input-type = <1>;
> + debounce-interval = <100>;
> + gpio-key,wakeup;
> + };
> +
> + menu {
> + gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_MENU>;
> + label = "Key Menu";
> + linux,input-type = <1>;
> + debounce-interval = <100>;
> + gpio-key,wakeup;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + led1 {
> + gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + led2 {
> + gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> + };
> +
> + panel1: lvds-panel {
> + compatible = "sgd,gktw70sdae4se", "panel-lvds";
> + backlight = <&backlight_lvds>;
> +
> + width-mm = <153>;
> + height-mm = <86>;
> +
> + label = "gktw70sdae4se";
> +
> + data-mapping = "jeida-18";
> +
> + panel-timing {
> + clock-frequency = <32000000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <39>;
> + hfront-porch = <39>;
> + vback-porch = <29>;
> + vfront-porch = <13>;
> + hsync-len = <47>;
> + vsync-len = <2>;
> + };
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds1_out>;
> + };
> + };
> + };
> +
> + reg_usb_h1_vbus: regulator-usbh1vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
Is this really GPIO_ACTIVE_HIGH?
If so, then a 'enable-active-high' property would be needed.
> + };
> +
> + reg_usb_otg_vbus: regulator-usbotgvbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
Ditto.
^ permalink raw reply [flat|nested] 32+ messages in thread* [PATCH v2 5/6] ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support
@ 2017-11-24 14:33 ` Fabio Estevam
0 siblings, 0 replies; 32+ messages in thread
From: Fabio Estevam @ 2017-11-24 14:33 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Nov 22, 2017 at 9:02 AM, Neil Armstrong <narmstrong@baylibre.com> wrote:
> This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
> SoM Carrier-Board.
>
> This Carrier-Board has the following :
> - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
> - HDMI Connector
> - USB Host + USB OTG Connector
> - 10/100/1000 Mbps Ethernet
> - miniPCI-Express slot
> - SD Card connector
> - Audio Headphone/Line In jack connectors
> - On-board DMIC
> - CAN bus header
> - SPI header
> - Camera Interfaces header
> - 4xButtons, 2xLeds
> - OnBoard RTC with Coin Backup battery socket
> - RS232 Header + USB-Serial debug port
>
> Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits
>
> The board support is done with all on-board and header interfaces enabled.
> 7" LVDS Touchscreen is enabled by default along HDMI output.
> Audio interface is supported with the "simple-card" bindings.
>
> PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-var-dt6customboard.dts | 238 +++++++++++++++++++++++++
> 2 files changed, 239 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-var-dt6customboard.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index d0381e9..148ff15 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -470,6 +470,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-tx6q-11x0-mb7.dtb \
> imx6q-udoo.dtb \
> imx6q-utilite-pro.dtb \
> + imx6q-var-dt6customboard.dtb \
> imx6q-wandboard.dtb \
> imx6q-wandboard-revb1.dtb \
> imx6q-wandboard-revd1.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
> new file mode 100644
> index 0000000..de01755
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
> @@ -0,0 +1,238 @@
> +/*
> + * Support for Variscite DART-MX6 Carrier-board
> + *
> + * Copyright 2017 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + *
> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +#include "imx6qdl-var-dart.dtsi"
> +#include <dt-bindings/input/linux-event-codes.h>
> +
> +/ {
> + model = "Variscite DART-MX6 Carrier-board";
> + compatible = "variscite,dt6customboard", "fsl,imx6q";
> +
> + backlight_lvds: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 50000>;
> + brightness-levels = <0 4 8 16 32 64 128 248>;
> + default-brightness-level = <7>;
> + status = "okay";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + autorepeat;
> +
> + back {
> + gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_BACK>;
> + label = "Key Back";
> + linux,input-type = <1>;
> + debounce-interval = <100>;
> + gpio-key,wakeup;
> + };
> +
> + home {
> + gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_HOME>;
> + label = "Key Home";
> + linux,input-type = <1>;
> + debounce-interval = <100>;
> + gpio-key,wakeup;
> + };
> +
> + menu {
> + gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_MENU>;
> + label = "Key Menu";
> + linux,input-type = <1>;
> + debounce-interval = <100>;
> + gpio-key,wakeup;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + led1 {
> + gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + led2 {
> + gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> + };
> +
> + panel1: lvds-panel {
> + compatible = "sgd,gktw70sdae4se", "panel-lvds";
> + backlight = <&backlight_lvds>;
> +
> + width-mm = <153>;
> + height-mm = <86>;
> +
> + label = "gktw70sdae4se";
> +
> + data-mapping = "jeida-18";
> +
> + panel-timing {
> + clock-frequency = <32000000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <39>;
> + hfront-porch = <39>;
> + vback-porch = <29>;
> + vfront-porch = <13>;
> + hsync-len = <47>;
> + vsync-len = <2>;
> + };
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds1_out>;
> + };
> + };
> + };
> +
> + reg_usb_h1_vbus: regulator-usbh1vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
Is this really GPIO_ACTIVE_HIGH?
If so, then a 'enable-active-high' property would be needed.
> + };
> +
> + reg_usb_otg_vbus: regulator-usbotgvbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
Ditto.
^ permalink raw reply [flat|nested] 32+ messages in thread* Re: [PATCH v2 5/6] ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support
2017-11-24 14:33 ` Fabio Estevam
@ 2017-11-24 14:41 ` Neil Armstrong
-1 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-24 14:41 UTC (permalink / raw)
To: Fabio Estevam
Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-kernel, linux-arm-kernel
On 24/11/2017 15:33, Fabio Estevam wrote:
> On Wed, Nov 22, 2017 at 9:02 AM, Neil Armstrong <narmstrong@baylibre.com> wrote:
>> This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
>> SoM Carrier-Board.
>>
>> This Carrier-Board has the following :
>> - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
>> - HDMI Connector
>> - USB Host + USB OTG Connector
>> - 10/100/1000 Mbps Ethernet
>> - miniPCI-Express slot
>> - SD Card connector
>> - Audio Headphone/Line In jack connectors
>> - On-board DMIC
>> - CAN bus header
>> - SPI header
>> - Camera Interfaces header
>> - 4xButtons, 2xLeds
>> - OnBoard RTC with Coin Backup battery socket
>> - RS232 Header + USB-Serial debug port
>>
>> Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits
>>
>> The board support is done with all on-board and header interfaces enabled.
>> 7" LVDS Touchscreen is enabled by default along HDMI output.
>> Audio interface is supported with the "simple-card" bindings.
>>
>> PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
>>
>> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>> ---
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/imx6q-var-dt6customboard.dts | 238 +++++++++++++++++++++++++
>> 2 files changed, 239 insertions(+)
>> create mode 100644 arch/arm/boot/dts/imx6q-var-dt6customboard.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index d0381e9..148ff15 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -470,6 +470,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>> imx6q-tx6q-11x0-mb7.dtb \
>> imx6q-udoo.dtb \
>> imx6q-utilite-pro.dtb \
>> + imx6q-var-dt6customboard.dtb \
>> imx6q-wandboard.dtb \
>> imx6q-wandboard-revb1.dtb \
>> imx6q-wandboard-revd1.dtb \
>> diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
>> new file mode 100644
>> index 0000000..de01755
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
>> @@ -0,0 +1,238 @@
>> +/*
>> + * Support for Variscite DART-MX6 Carrier-board
>> + *
>> + * Copyright 2017 BayLibre, SAS
>> + * Author: Neil Armstrong <narmstrong@baylibre.com>
>> + *
>> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "imx6q.dtsi"
>> +#include "imx6qdl-var-dart.dtsi"
>> +#include <dt-bindings/input/linux-event-codes.h>
>> +
>> +/ {
>> + model = "Variscite DART-MX6 Carrier-board";
>> + compatible = "variscite,dt6customboard", "fsl,imx6q";
>> +
>> + backlight_lvds: backlight {
>> + compatible = "pwm-backlight";
>> + pwms = <&pwm2 0 50000>;
>> + brightness-levels = <0 4 8 16 32 64 128 248>;
>> + default-brightness-level = <7>;
>> + status = "okay";
>> + };
>> +
>> + gpio-keys {
>> + compatible = "gpio-keys";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + autorepeat;
>> +
>> + back {
>> + gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
>> + linux,code = <KEY_BACK>;
>> + label = "Key Back";
>> + linux,input-type = <1>;
>> + debounce-interval = <100>;
>> + gpio-key,wakeup;
>> + };
>> +
>> + home {
>> + gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
>> + linux,code = <KEY_HOME>;
>> + label = "Key Home";
>> + linux,input-type = <1>;
>> + debounce-interval = <100>;
>> + gpio-key,wakeup;
>> + };
>> +
>> + menu {
>> + gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
>> + linux,code = <KEY_MENU>;
>> + label = "Key Menu";
>> + linux,input-type = <1>;
>> + debounce-interval = <100>;
>> + gpio-key,wakeup;
>> + };
>> + };
>> +
>> + gpio-leds {
>> + compatible = "gpio-leds";
>> +
>> + led1 {
>> + gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
>> + linux,default-trigger = "heartbeat";
>> + };
>> +
>> + led2 {
>> + gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
>> + linux,default-trigger = "default-on";
>> + };
>> + };
>> +
>> + panel1: lvds-panel {
>> + compatible = "sgd,gktw70sdae4se", "panel-lvds";
>> + backlight = <&backlight_lvds>;
>> +
>> + width-mm = <153>;
>> + height-mm = <86>;
>> +
>> + label = "gktw70sdae4se";
>> +
>> + data-mapping = "jeida-18";
>> +
>> + panel-timing {
>> + clock-frequency = <32000000>;
>> + hactive = <800>;
>> + vactive = <480>;
>> + hback-porch = <39>;
>> + hfront-porch = <39>;
>> + vback-porch = <29>;
>> + vfront-porch = <13>;
>> + hsync-len = <47>;
>> + vsync-len = <2>;
>> + };
>> +
>> + port {
>> + panel_in: endpoint {
>> + remote-endpoint = <&lvds1_out>;
>> + };
>> + };
>> + };
>> +
>> + reg_usb_h1_vbus: regulator-usbh1vbus {
>> + compatible = "regulator-fixed";
>> + regulator-name = "usb_h1_vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
>
> Is this really GPIO_ACTIVE_HIGH?
>
> If so, then a 'enable-active-high' property would be needed.
Ok.
>
>> + };
>> +
>> + reg_usb_otg_vbus: regulator-usbotgvbus {
>> + compatible = "regulator-fixed";
>> + regulator-name = "usb_otg_vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
>
> Ditto.
>
Ok.
Thanks,
Neil
^ permalink raw reply [flat|nested] 32+ messages in thread* [PATCH v2 5/6] ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support
@ 2017-11-24 14:41 ` Neil Armstrong
0 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-24 14:41 UTC (permalink / raw)
To: linux-arm-kernel
On 24/11/2017 15:33, Fabio Estevam wrote:
> On Wed, Nov 22, 2017 at 9:02 AM, Neil Armstrong <narmstrong@baylibre.com> wrote:
>> This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
>> SoM Carrier-Board.
>>
>> This Carrier-Board has the following :
>> - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
>> - HDMI Connector
>> - USB Host + USB OTG Connector
>> - 10/100/1000 Mbps Ethernet
>> - miniPCI-Express slot
>> - SD Card connector
>> - Audio Headphone/Line In jack connectors
>> - On-board DMIC
>> - CAN bus header
>> - SPI header
>> - Camera Interfaces header
>> - 4xButtons, 2xLeds
>> - OnBoard RTC with Coin Backup battery socket
>> - RS232 Header + USB-Serial debug port
>>
>> Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits
>>
>> The board support is done with all on-board and header interfaces enabled.
>> 7" LVDS Touchscreen is enabled by default along HDMI output.
>> Audio interface is supported with the "simple-card" bindings.
>>
>> PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
>>
>> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>> ---
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/imx6q-var-dt6customboard.dts | 238 +++++++++++++++++++++++++
>> 2 files changed, 239 insertions(+)
>> create mode 100644 arch/arm/boot/dts/imx6q-var-dt6customboard.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index d0381e9..148ff15 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -470,6 +470,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>> imx6q-tx6q-11x0-mb7.dtb \
>> imx6q-udoo.dtb \
>> imx6q-utilite-pro.dtb \
>> + imx6q-var-dt6customboard.dtb \
>> imx6q-wandboard.dtb \
>> imx6q-wandboard-revb1.dtb \
>> imx6q-wandboard-revd1.dtb \
>> diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
>> new file mode 100644
>> index 0000000..de01755
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
>> @@ -0,0 +1,238 @@
>> +/*
>> + * Support for Variscite DART-MX6 Carrier-board
>> + *
>> + * Copyright 2017 BayLibre, SAS
>> + * Author: Neil Armstrong <narmstrong@baylibre.com>
>> + *
>> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "imx6q.dtsi"
>> +#include "imx6qdl-var-dart.dtsi"
>> +#include <dt-bindings/input/linux-event-codes.h>
>> +
>> +/ {
>> + model = "Variscite DART-MX6 Carrier-board";
>> + compatible = "variscite,dt6customboard", "fsl,imx6q";
>> +
>> + backlight_lvds: backlight {
>> + compatible = "pwm-backlight";
>> + pwms = <&pwm2 0 50000>;
>> + brightness-levels = <0 4 8 16 32 64 128 248>;
>> + default-brightness-level = <7>;
>> + status = "okay";
>> + };
>> +
>> + gpio-keys {
>> + compatible = "gpio-keys";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + autorepeat;
>> +
>> + back {
>> + gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
>> + linux,code = <KEY_BACK>;
>> + label = "Key Back";
>> + linux,input-type = <1>;
>> + debounce-interval = <100>;
>> + gpio-key,wakeup;
>> + };
>> +
>> + home {
>> + gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
>> + linux,code = <KEY_HOME>;
>> + label = "Key Home";
>> + linux,input-type = <1>;
>> + debounce-interval = <100>;
>> + gpio-key,wakeup;
>> + };
>> +
>> + menu {
>> + gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
>> + linux,code = <KEY_MENU>;
>> + label = "Key Menu";
>> + linux,input-type = <1>;
>> + debounce-interval = <100>;
>> + gpio-key,wakeup;
>> + };
>> + };
>> +
>> + gpio-leds {
>> + compatible = "gpio-leds";
>> +
>> + led1 {
>> + gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
>> + linux,default-trigger = "heartbeat";
>> + };
>> +
>> + led2 {
>> + gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
>> + linux,default-trigger = "default-on";
>> + };
>> + };
>> +
>> + panel1: lvds-panel {
>> + compatible = "sgd,gktw70sdae4se", "panel-lvds";
>> + backlight = <&backlight_lvds>;
>> +
>> + width-mm = <153>;
>> + height-mm = <86>;
>> +
>> + label = "gktw70sdae4se";
>> +
>> + data-mapping = "jeida-18";
>> +
>> + panel-timing {
>> + clock-frequency = <32000000>;
>> + hactive = <800>;
>> + vactive = <480>;
>> + hback-porch = <39>;
>> + hfront-porch = <39>;
>> + vback-porch = <29>;
>> + vfront-porch = <13>;
>> + hsync-len = <47>;
>> + vsync-len = <2>;
>> + };
>> +
>> + port {
>> + panel_in: endpoint {
>> + remote-endpoint = <&lvds1_out>;
>> + };
>> + };
>> + };
>> +
>> + reg_usb_h1_vbus: regulator-usbh1vbus {
>> + compatible = "regulator-fixed";
>> + regulator-name = "usb_h1_vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
>
> Is this really GPIO_ACTIVE_HIGH?
>
> If so, then a 'enable-active-high' property would be needed.
Ok.
>
>> + };
>> +
>> + reg_usb_otg_vbus: regulator-usbotgvbus {
>> + compatible = "regulator-fixed";
>> + regulator-name = "usb_otg_vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
>
> Ditto.
>
Ok.
Thanks,
Neil
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2 6/6] ARM: configs: Add missing config for DART-MX6 SoM
2017-11-22 11:02 ` Neil Armstrong
@ 2017-11-22 11:02 ` Neil Armstrong
-1 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: Neil Armstrong, linux-arm-kernel, linux-kernel
This patch adds the missing configs for the DART-MX6 SoM support :
- SERDEV bluetooth driver + SERIAL_DEV_BUS configs
- WL18XX driver
- DEFAULT_ON Led Trigger
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/configs/imx_v6_v7_defconfig | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 0d44949..abd06c3 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -80,6 +80,7 @@ CONFIG_CAN=y
CONFIG_CAN_FLEXCAN=y
CONFIG_BT=y
CONFIG_BT_HCIUART=y
+CONFIG_BT_HCIUART_SERDEV=y
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_LL=y
CONFIG_CFG80211=y
@@ -155,6 +156,7 @@ CONFIG_USB_USBNET=y
CONFIG_USB_NET_CDC_EEM=m
CONFIG_BRCMFMAC=m
CONFIG_WL12XX=m
+CONFIG_WL18XX=m
CONFIG_WLCORE_SDIO=m
# CONFIG_WILINK_PLATFORM_DATA is not set
CONFIG_INPUT_EVDEV=y
@@ -185,6 +187,8 @@ CONFIG_SERIAL_IMX=y
CONFIG_SERIAL_IMX_CONSOLE=y
CONFIG_SERIAL_FSL_LPUART=y
CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
+CONFIG_SERIAL_DEV_BUS=y
+CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
# CONFIG_I2C_COMPAT is not set
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MUX=y
@@ -248,6 +252,7 @@ CONFIG_VIDEO_OV5640=m
CONFIG_SOC_CAMERA_OV2640=y
CONFIG_IMX_IPUV3_CORE=y
CONFIG_DRM=y
+CONFIG_DRM_PANEL_LVDS=y
CONFIG_DRM_PANEL_SIMPLE=y
CONFIG_DRM_DW_HDMI_AHB_AUDIO=m
CONFIG_DRM_DW_HDMI_CEC=y
@@ -340,6 +345,7 @@ CONFIG_LEDS_TRIGGER_ONESHOT=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
CONFIG_LEDS_TRIGGER_BACKLIGHT=y
CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_INTF_DEV_UIE_EMUL=y
CONFIG_RTC_DRV_DS1307=y
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread
* [PATCH v2 6/6] ARM: configs: Add missing config for DART-MX6 SoM
@ 2017-11-22 11:02 ` Neil Armstrong
0 siblings, 0 replies; 32+ messages in thread
From: Neil Armstrong @ 2017-11-22 11:02 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds the missing configs for the DART-MX6 SoM support :
- SERDEV bluetooth driver + SERIAL_DEV_BUS configs
- WL18XX driver
- DEFAULT_ON Led Trigger
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/configs/imx_v6_v7_defconfig | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 0d44949..abd06c3 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -80,6 +80,7 @@ CONFIG_CAN=y
CONFIG_CAN_FLEXCAN=y
CONFIG_BT=y
CONFIG_BT_HCIUART=y
+CONFIG_BT_HCIUART_SERDEV=y
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_LL=y
CONFIG_CFG80211=y
@@ -155,6 +156,7 @@ CONFIG_USB_USBNET=y
CONFIG_USB_NET_CDC_EEM=m
CONFIG_BRCMFMAC=m
CONFIG_WL12XX=m
+CONFIG_WL18XX=m
CONFIG_WLCORE_SDIO=m
# CONFIG_WILINK_PLATFORM_DATA is not set
CONFIG_INPUT_EVDEV=y
@@ -185,6 +187,8 @@ CONFIG_SERIAL_IMX=y
CONFIG_SERIAL_IMX_CONSOLE=y
CONFIG_SERIAL_FSL_LPUART=y
CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
+CONFIG_SERIAL_DEV_BUS=y
+CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
# CONFIG_I2C_COMPAT is not set
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MUX=y
@@ -248,6 +252,7 @@ CONFIG_VIDEO_OV5640=m
CONFIG_SOC_CAMERA_OV2640=y
CONFIG_IMX_IPUV3_CORE=y
CONFIG_DRM=y
+CONFIG_DRM_PANEL_LVDS=y
CONFIG_DRM_PANEL_SIMPLE=y
CONFIG_DRM_DW_HDMI_AHB_AUDIO=m
CONFIG_DRM_DW_HDMI_CEC=y
@@ -340,6 +345,7 @@ CONFIG_LEDS_TRIGGER_ONESHOT=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
CONFIG_LEDS_TRIGGER_BACKLIGHT=y
CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_INTF_DEV_UIE_EMUL=y
CONFIG_RTC_DRV_DS1307=y
--
2.7.4
^ permalink raw reply related [flat|nested] 32+ messages in thread