* [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP
@ 2021-08-16 10:44 Ye Li
2021-08-16 10:44 ` [PATCH 2/7] arm: mach-imx: Allow to build mac.c for EQoS driver Ye Li
` (7 more replies)
0 siblings, 8 replies; 15+ messages in thread
From: Ye Li @ 2021-08-16 10:44 UTC (permalink / raw)
To: sbabic, u-boot, festevam, peng.fan; +Cc: uboot-imx, marex, rfried.dev, s.arendt
i.MX8MP has two ENET controllers, have to update the function to
enable loading two MAC addresses.
Signed-off-by: Ye Li <ye.li@nxp.com>
---
arch/arm/mach-imx/mac.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/mach-imx/mac.c b/arch/arm/mach-imx/mac.c
index 3b1496b..9bb63d2 100644
--- a/arch/arm/mach-imx/mac.c
+++ b/arch/arm/mach-imx/mac.c
@@ -31,7 +31,7 @@ void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
offset = is_mx6() ? MAC_FUSE_MX6_OFFSET : MAC_FUSE_MX7_OFFSET;
fuse = (struct imx_mac_fuse *)(ulong)(OCOTP_BASE_ADDR + offset);
- has_second_mac = is_mx7() || is_mx6sx() || is_mx6ul() || is_mx6ull();
+ has_second_mac = is_mx7() || is_mx6sx() || is_mx6ul() || is_mx6ull() || is_imx8mp();
if (has_second_mac && dev_id == 1) {
u32 value = readl(&fuse->mac_addr2);
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 2/7] arm: mach-imx: Allow to build mac.c for EQoS driver
2021-08-16 10:44 [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Ye Li
@ 2021-08-16 10:44 ` Ye Li
2021-10-21 14:13 ` sbabic
2021-08-16 10:44 ` [PATCH 3/7] arm: dts: imx8mp-evk: Enable the EQoS ethernet port Ye Li
` (6 subsequent siblings)
7 siblings, 1 reply; 15+ messages in thread
From: Ye Li @ 2021-08-16 10:44 UTC (permalink / raw)
To: sbabic, u-boot, festevam, peng.fan; +Cc: uboot-imx, marex, rfried.dev, s.arendt
i.MX8MP has one DWC EQoS controller, so allow to build mac.c when
only this driver is enabled.
Signed-off-by: Ye Li <ye.li@nxp.com>
---
arch/arm/mach-imx/Makefile | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index 0ef2695..74a2a2a 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_IMX_BOOTAUX) += imx_bootaux.o
endif
obj-$(CONFIG_ENV_IS_IN_MMC) += mmc_env.o
obj-$(CONFIG_FEC_MXC) += mac.o
+obj-$(CONFIG_DWC_ETH_QOS) += mac.o
obj-$(CONFIG_SYS_I2C_MXC) += i2c-mxv7.o
obj-$(CONFIG_IMX_HAB) += hab.o
obj-y += cpu.o
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 3/7] arm: dts: imx8mp-evk: Enable the EQoS ethernet port
2021-08-16 10:44 [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Ye Li
2021-08-16 10:44 ` [PATCH 2/7] arm: mach-imx: Allow to build mac.c for EQoS driver Ye Li
@ 2021-08-16 10:44 ` Ye Li
2021-10-21 14:12 ` sbabic
2021-08-16 10:44 ` [PATCH 4/7] imx8mp_evk: Fix incorrect cascade for FEC and EQOS setup Ye Li
` (5 subsequent siblings)
7 siblings, 1 reply; 15+ messages in thread
From: Ye Li @ 2021-08-16 10:44 UTC (permalink / raw)
To: sbabic, u-boot, festevam, peng.fan; +Cc: uboot-imx, marex, rfried.dev, s.arendt
i.MX8MP EVK has two ethernet ports. Add relevant nodes and properties
for EQoS port to the EVK DTS file.
In -u-boot.dtsi, change the u-boot eqos compatible string, add PHY
reset gpio and remove assigned clocks as not supported in CCF.
Signed-off-by: Ye Li <ye.li@nxp.com>
---
arch/arm/dts/imx8mp-evk-u-boot.dtsi | 13 ++++++++++++
arch/arm/dts/imx8mp-evk.dts | 40 +++++++++++++++++++++++++++++++++++++
2 files changed, 53 insertions(+)
diff --git a/arch/arm/dts/imx8mp-evk-u-boot.dtsi b/arch/arm/dts/imx8mp-evk-u-boot.dtsi
index 2abcf1f..ab849eb 100644
--- a/arch/arm/dts/imx8mp-evk-u-boot.dtsi
+++ b/arch/arm/dts/imx8mp-evk-u-boot.dtsi
@@ -111,6 +111,19 @@
u-boot,dm-spl;
};
+&eqos {
+ compatible = "fsl,imx-eqos";
+ /delete-property/ assigned-clocks;
+ /delete-property/ assigned-clock-parents;
+ /delete-property/ assigned-clock-rates;
+};
+
+ðphy0 {
+ reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <15000>;
+ reset-post-delay-us = <100000>;
+};
+
&fec {
phy-reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
phy-reset-duration = <15>;
diff --git a/arch/arm/dts/imx8mp-evk.dts b/arch/arm/dts/imx8mp-evk.dts
index b10dce8..f846d69 100644
--- a/arch/arm/dts/imx8mp-evk.dts
+++ b/arch/arm/dts/imx8mp-evk.dts
@@ -74,6 +74,26 @@
status = "okay";
};
+&eqos {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eqos>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ eee-broken-1000t;
+ };
+ };
+};
+
&flexcan2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flexcan2>;
@@ -160,6 +180,26 @@
};
&iomuxc {
+ pinctrl_eqos: eqosgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3
+ MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3
+ MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91
+ MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91
+ MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91
+ MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91
+ MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91
+ MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91
+ MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f
+ MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f
+ MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f
+ MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f
+ MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f
+ MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f
+ MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22 0x19
+ >;
+ };
+
pinctrl_fec: fecgrp {
fsl,pins = <
MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 4/7] imx8mp_evk: Fix incorrect cascade for FEC and EQOS setup
2021-08-16 10:44 [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Ye Li
2021-08-16 10:44 ` [PATCH 2/7] arm: mach-imx: Allow to build mac.c for EQoS driver Ye Li
2021-08-16 10:44 ` [PATCH 3/7] arm: dts: imx8mp-evk: Enable the EQoS ethernet port Ye Li
@ 2021-08-16 10:44 ` Ye Li
2021-10-21 14:12 ` sbabic
2021-08-16 10:44 ` [PATCH 5/7] imx8mp_evk: Remove EQoS PHY reset codes Ye Li
` (4 subsequent siblings)
7 siblings, 1 reply; 15+ messages in thread
From: Ye Li @ 2021-08-16 10:44 UTC (permalink / raw)
To: sbabic, u-boot, festevam, peng.fan; +Cc: uboot-imx, marex, rfried.dev, s.arendt
The setup functions should be independent for two ethernet controllers
Signed-off-by: Ye Li <ye.li@nxp.com>
---
board/freescale/imx8mp_evk/imx8mp_evk.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/board/freescale/imx8mp_evk/imx8mp_evk.c b/board/freescale/imx8mp_evk/imx8mp_evk.c
index 89cc17c..bc4753c 100644
--- a/board/freescale/imx8mp_evk/imx8mp_evk.c
+++ b/board/freescale/imx8mp_evk/imx8mp_evk.c
@@ -101,9 +101,10 @@ int board_init(void)
if (CONFIG_IS_ENABLED(FEC_MXC)) {
setup_fec();
+ }
- if (CONFIG_IS_ENABLED(DWC_ETH_QOS))
- ret = setup_eqos();
+ if (CONFIG_IS_ENABLED(DWC_ETH_QOS)) {
+ ret = setup_eqos();
}
return ret;
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 5/7] imx8mp_evk: Remove EQoS PHY reset codes
2021-08-16 10:44 [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Ye Li
` (2 preceding siblings ...)
2021-08-16 10:44 ` [PATCH 4/7] imx8mp_evk: Fix incorrect cascade for FEC and EQOS setup Ye Li
@ 2021-08-16 10:44 ` Ye Li
2021-10-21 14:12 ` sbabic
2021-08-16 10:44 ` [PATCH 6/7] imx8mp_evk: Delete noncached memory config Ye Li
` (3 subsequent siblings)
7 siblings, 1 reply; 15+ messages in thread
From: Ye Li @ 2021-08-16 10:44 UTC (permalink / raw)
To: sbabic, u-boot, festevam, peng.fan; +Cc: uboot-imx, marex, rfried.dev, s.arendt
Since we uses the DTS and PHY reset gpio in EQoS driver to do the
reset, remove the duplicated codes from board file.
Signed-off-by: Ye Li <ye.li@nxp.com>
---
board/freescale/imx8mp_evk/imx8mp_evk.c | 19 -------------------
1 file changed, 19 deletions(-)
diff --git a/board/freescale/imx8mp_evk/imx8mp_evk.c b/board/freescale/imx8mp_evk/imx8mp_evk.c
index bc4753c..62096c2 100644
--- a/board/freescale/imx8mp_evk/imx8mp_evk.c
+++ b/board/freescale/imx8mp_evk/imx8mp_evk.c
@@ -54,30 +54,11 @@ static void setup_fec(void)
setbits_le32(&gpr->gpr[1], BIT(22));
}
-#define EQOS_RST_PAD IMX_GPIO_NR(4, 22)
-static iomux_v3_cfg_t const eqos_rst_pads[] = {
- MX8MP_PAD_SAI2_RXC__GPIO4_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void setup_iomux_eqos(void)
-{
- imx_iomux_v3_setup_multiple_pads(eqos_rst_pads,
- ARRAY_SIZE(eqos_rst_pads));
-
- gpio_request(EQOS_RST_PAD, "eqos_rst");
- gpio_direction_output(EQOS_RST_PAD, 0);
- mdelay(15);
- gpio_direction_output(EQOS_RST_PAD, 1);
- mdelay(100);
-}
-
static int setup_eqos(void)
{
struct iomuxc_gpr_base_regs *gpr =
(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
- setup_iomux_eqos();
-
/* set INTF as RGMII, enable RGMII TXC clock */
clrsetbits_le32(&gpr->gpr[1],
IOMUXC_GPR_GPR1_GPR_ENET_QOS_INTF_SEL_MASK, BIT(16));
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 6/7] imx8mp_evk: Delete noncached memory config
2021-08-16 10:44 [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Ye Li
` (3 preceding siblings ...)
2021-08-16 10:44 ` [PATCH 5/7] imx8mp_evk: Remove EQoS PHY reset codes Ye Li
@ 2021-08-16 10:44 ` Ye Li
2021-10-21 14:12 ` sbabic
2021-08-16 10:44 ` [PATCH 7/7] imx8mp_evk: Enable the DWC EQoS iMX driver Ye Li
` (2 subsequent siblings)
7 siblings, 1 reply; 15+ messages in thread
From: Ye Li @ 2021-08-16 10:44 UTC (permalink / raw)
To: sbabic, u-boot, festevam, peng.fan; +Cc: uboot-imx, marex, rfried.dev, s.arendt
DWC EQOS driver has removed to use noncached memory, so delete
the configuration from iMX8MP EVK head file.
Signed-off-by: Ye Li <ye.li@nxp.com>
---
include/configs/imx8mp_evk.h | 3 ---
1 file changed, 3 deletions(-)
diff --git a/include/configs/imx8mp_evk.h b/include/configs/imx8mp_evk.h
index a6569d5..59e50fe 100644
--- a/include/configs/imx8mp_evk.h
+++ b/include/configs/imx8mp_evk.h
@@ -49,9 +49,6 @@
#define FEC_QUIRK_ENET_MAC
#define DWC_NET_PHYADDR 1
-#ifdef CONFIG_DWC_ETH_QOS
-#define CONFIG_SYS_NONCACHED_MEMORY (1 * SZ_1M) /* 1M */
-#endif
#define PHY_ANEG_TIMEOUT 20000
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 7/7] imx8mp_evk: Enable the DWC EQoS iMX driver
2021-08-16 10:44 [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Ye Li
` (4 preceding siblings ...)
2021-08-16 10:44 ` [PATCH 6/7] imx8mp_evk: Delete noncached memory config Ye Li
@ 2021-08-16 10:44 ` Ye Li
2021-10-21 14:12 ` sbabic
2021-10-10 8:35 ` [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Marcel Ziswiler
2021-10-21 14:13 ` sbabic
7 siblings, 1 reply; 15+ messages in thread
From: Ye Li @ 2021-08-16 10:44 UTC (permalink / raw)
To: sbabic, u-boot, festevam, peng.fan; +Cc: uboot-imx, marex, rfried.dev, s.arendt
Enable the EQoS i.MX driver in defconfig, also enable the PHYLIB
to facilitate the case that only has FEC enabled.
Signed-off-by: Ye Li <ye.li@nxp.com>
---
configs/imx8mp_evk_defconfig | 3 +++
1 file changed, 3 insertions(+)
diff --git a/configs/imx8mp_evk_defconfig b/configs/imx8mp_evk_defconfig
index 2c6fc16..41e6b2f 100644
--- a/configs/imx8mp_evk_defconfig
+++ b/configs/imx8mp_evk_defconfig
@@ -72,9 +72,12 @@ CONFIG_MMC_HS400_ES_SUPPORT=y
CONFIG_MMC_HS400_SUPPORT=y
CONFIG_FSL_ESDHC_IMX=y
CONFIG_PHY_REALTEK=y
+CONFIG_PHYLIB=y
CONFIG_DM_ETH=y
+CONFIG_DM_ETH_PHY=y
CONFIG_PHY_GIGE=y
CONFIG_DWC_ETH_QOS=y
+CONFIG_DWC_ETH_QOS_IMX=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP
2021-08-16 10:44 [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Ye Li
` (5 preceding siblings ...)
2021-08-16 10:44 ` [PATCH 7/7] imx8mp_evk: Enable the DWC EQoS iMX driver Ye Li
@ 2021-10-10 8:35 ` Marcel Ziswiler
2021-10-21 14:13 ` sbabic
7 siblings, 0 replies; 15+ messages in thread
From: Marcel Ziswiler @ 2021-10-10 8:35 UTC (permalink / raw)
To: festevam, u-boot, sbabic, ye.li, peng.fan
Cc: s.arendt, marex, uboot-imx, rfried.dev
On Mon, 2021-08-16 at 18:44 +0800, Ye Li wrote:
> i.MX8MP has two ENET controllers, have to update the function to
> enable loading two MAC addresses.
>
> Signed-off-by: Ye Li <ye.li@nxp.com>
Whole series.
Tested on iMX8MP_EVK and Verdin iMX8M Plus on Verdin development board.
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
I will post the Verdin iMX8M Plus support shortly.
> ---
> arch/arm/mach-imx/mac.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm/mach-imx/mac.c b/arch/arm/mach-imx/mac.c
> index 3b1496b..9bb63d2 100644
> --- a/arch/arm/mach-imx/mac.c
> +++ b/arch/arm/mach-imx/mac.c
> @@ -31,7 +31,7 @@ void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
>
> offset = is_mx6() ? MAC_FUSE_MX6_OFFSET : MAC_FUSE_MX7_OFFSET;
> fuse = (struct imx_mac_fuse *)(ulong)(OCOTP_BASE_ADDR + offset);
> - has_second_mac = is_mx7() || is_mx6sx() || is_mx6ul() || is_mx6ull();
> + has_second_mac = is_mx7() || is_mx6sx() || is_mx6ul() || is_mx6ull() || is_imx8mp();
>
> if (has_second_mac && dev_id == 1) {
> u32 value = readl(&fuse->mac_addr2);
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 7/7] imx8mp_evk: Enable the DWC EQoS iMX driver
2021-08-16 10:44 ` [PATCH 7/7] imx8mp_evk: Enable the DWC EQoS iMX driver Ye Li
@ 2021-10-21 14:12 ` sbabic
0 siblings, 0 replies; 15+ messages in thread
From: sbabic @ 2021-10-21 14:12 UTC (permalink / raw)
To: Ye Li, u-boot
> Enable the EQoS i.MX driver in defconfig, also enable the PHYLIB
> to facilitate the case that only has FEC enabled.
> Signed-off-by: Ye Li <ye.li@nxp.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 4/7] imx8mp_evk: Fix incorrect cascade for FEC and EQOS setup
2021-08-16 10:44 ` [PATCH 4/7] imx8mp_evk: Fix incorrect cascade for FEC and EQOS setup Ye Li
@ 2021-10-21 14:12 ` sbabic
0 siblings, 0 replies; 15+ messages in thread
From: sbabic @ 2021-10-21 14:12 UTC (permalink / raw)
To: Ye Li, u-boot
> The setup functions should be independent for two ethernet controllers
> Signed-off-by: Ye Li <ye.li@nxp.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 5/7] imx8mp_evk: Remove EQoS PHY reset codes
2021-08-16 10:44 ` [PATCH 5/7] imx8mp_evk: Remove EQoS PHY reset codes Ye Li
@ 2021-10-21 14:12 ` sbabic
0 siblings, 0 replies; 15+ messages in thread
From: sbabic @ 2021-10-21 14:12 UTC (permalink / raw)
To: Ye Li, u-boot
> Since we uses the DTS and PHY reset gpio in EQoS driver to do the
> reset, remove the duplicated codes from board file.
> Signed-off-by: Ye Li <ye.li@nxp.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 3/7] arm: dts: imx8mp-evk: Enable the EQoS ethernet port
2021-08-16 10:44 ` [PATCH 3/7] arm: dts: imx8mp-evk: Enable the EQoS ethernet port Ye Li
@ 2021-10-21 14:12 ` sbabic
0 siblings, 0 replies; 15+ messages in thread
From: sbabic @ 2021-10-21 14:12 UTC (permalink / raw)
To: Ye Li, u-boot
> i.MX8MP EVK has two ethernet ports. Add relevant nodes and properties
> for EQoS port to the EVK DTS file.
> In -u-boot.dtsi, change the u-boot eqos compatible string, add PHY
> reset gpio and remove assigned clocks as not supported in CCF.
> Signed-off-by: Ye Li <ye.li@nxp.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 6/7] imx8mp_evk: Delete noncached memory config
2021-08-16 10:44 ` [PATCH 6/7] imx8mp_evk: Delete noncached memory config Ye Li
@ 2021-10-21 14:12 ` sbabic
0 siblings, 0 replies; 15+ messages in thread
From: sbabic @ 2021-10-21 14:12 UTC (permalink / raw)
To: Ye Li, u-boot
> DWC EQOS driver has removed to use noncached memory, so delete
> the configuration from iMX8MP EVK head file.
> Signed-off-by: Ye Li <ye.li@nxp.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP
2021-08-16 10:44 [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Ye Li
` (6 preceding siblings ...)
2021-10-10 8:35 ` [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Marcel Ziswiler
@ 2021-10-21 14:13 ` sbabic
7 siblings, 0 replies; 15+ messages in thread
From: sbabic @ 2021-10-21 14:13 UTC (permalink / raw)
To: Ye Li, u-boot
> i.MX8MP has two ENET controllers, have to update the function to
> enable loading two MAC addresses.
> Signed-off-by: Ye Li <ye.li@nxp.com>
> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 2/7] arm: mach-imx: Allow to build mac.c for EQoS driver
2021-08-16 10:44 ` [PATCH 2/7] arm: mach-imx: Allow to build mac.c for EQoS driver Ye Li
@ 2021-10-21 14:13 ` sbabic
0 siblings, 0 replies; 15+ messages in thread
From: sbabic @ 2021-10-21 14:13 UTC (permalink / raw)
To: Ye Li, u-boot
> i.MX8MP has one DWC EQoS controller, so allow to build mac.c when
> only this driver is enabled.
> Signed-off-by: Ye Li <ye.li@nxp.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2021-10-21 14:14 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-08-16 10:44 [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Ye Li
2021-08-16 10:44 ` [PATCH 2/7] arm: mach-imx: Allow to build mac.c for EQoS driver Ye Li
2021-10-21 14:13 ` sbabic
2021-08-16 10:44 ` [PATCH 3/7] arm: dts: imx8mp-evk: Enable the EQoS ethernet port Ye Li
2021-10-21 14:12 ` sbabic
2021-08-16 10:44 ` [PATCH 4/7] imx8mp_evk: Fix incorrect cascade for FEC and EQOS setup Ye Li
2021-10-21 14:12 ` sbabic
2021-08-16 10:44 ` [PATCH 5/7] imx8mp_evk: Remove EQoS PHY reset codes Ye Li
2021-10-21 14:12 ` sbabic
2021-08-16 10:44 ` [PATCH 6/7] imx8mp_evk: Delete noncached memory config Ye Li
2021-10-21 14:12 ` sbabic
2021-08-16 10:44 ` [PATCH 7/7] imx8mp_evk: Enable the DWC EQoS iMX driver Ye Li
2021-10-21 14:12 ` sbabic
2021-10-10 8:35 ` [PATCH 1/7] arm: mach-imx: Update MAC fuse for i.MX8MP Marcel Ziswiler
2021-10-21 14:13 ` sbabic
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.