* Linux NetRom Node Question
@ 2009-10-04 18:46 Jeremiah
2009-10-04 19:32 ` John Ronan
0 siblings, 1 reply; 6+ messages in thread
From: Jeremiah @ 2009-10-04 18:46 UTC (permalink / raw)
To: linux-hams
Hello all,
I am still working on setting up our RMS to send out NetRom Broadcasts. I have
added a "dummy" entry into the nrports file for connection outbound from the
node. I also corrected the entry for the RMS. Running nrattach it comes back
with "NET/ROM port winl2k bound to device nr0", but it never shows up when I
run ifconfig. There are no errors in the system logs when I run nrattach.
Does anyone have an example nrports file they would be willing to share? I'm
a bit stuck on this because the nr0 interface does not come up and the system
gives me no errors in /var/log/messages.
Thanks
Jeremiah
KD7DMP
nrports-------------
# /etc/ax25/nrports
#
# The format of this file is:
#
# name callsign alias paclen description
#
switch WR7VHF-14 #WINL2k 235 dummy for the RMS
winl2k WR7VHF-10 WINL2K 235 RMS
nrbroadcast------------
# /etc/ax25/nrbroadcast
#
# The format of this file is:
#
# ax25_name min_obs def_qual worst_qual verbose
#
pk96 5 250 100 0
axports-----------
# /etc/ax25/axports
#
# The format of this file is:
#
# name callsign speed paclen window description
#
pk96 wr7vhf 19200 255 4 BackBone Port
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Linux NetRom Node Question
2009-10-04 18:46 Linux NetRom Node Question Jeremiah
@ 2009-10-04 19:32 ` John Ronan
2009-10-05 4:32 ` Jeremiah
0 siblings, 1 reply; 6+ messages in thread
From: John Ronan @ 2009-10-04 19:32 UTC (permalink / raw)
To: Jeremiah; +Cc: linux-hams
Hi,
I don't use netrom as it was causing segfaults at one stage and as no
one around here uses netrom anymore I stopped.
however just out of curiosity I had a look
firstly
modprobe netrom
then
root@ns1:~# cat /etc/ax25/nrports
# /etc/ax25/nrports
#
# The format of this file is:
#
# name callsign alias paclen description
#
netrom EI7IG-14 #TMRE 235 Switch Port
netnod EI7IG-1 TMRE 235 Node
root@ns1:~# nrattach -i 44.155.6.12 -m 236 netrom
NET/ROM port netrom bound to device nr0
root@ns1:~# ifconfig nr0
nr0 Link encap:AMPR NET/ROM HWaddr EI7IG-14
inet addr:44.155.6.12 Mask:255.0.0.0
UP RUNNING NOARP MTU:236 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@ns1:~#
Regards
de John
EI7IG
On 4 Oct 2009, at 19:46, Jeremiah wrote:
> Hello all,
>
> I am still working on setting up our RMS to send out NetRom
> Broadcasts. I have
> added a "dummy" entry into the nrports file for connection outbound
> from the
> node. I also corrected the entry for the RMS. Running nrattach it
> comes back
> with "NET/ROM port winl2k bound to device nr0", but it never shows
> up when I
> run ifconfig. There are no errors in the system logs when I run
> nrattach.
> Does anyone have an example nrports file they would be willing to
> share? I'm
> a bit stuck on this because the nr0 interface does not come up and
> the system
> gives me no errors in /var/log/messages.
>
>
>
> Thanks
>
> Jeremiah
> KD7DMP
>
> nrports-------------
> # /etc/ax25/nrports
> #
> # The format of this file is:
> #
> # name callsign alias paclen description
> #
> switch WR7VHF-14 #WINL2k 235 dummy for the RMS
> winl2k WR7VHF-10 WINL2K 235 RMS
>
> nrbroadcast------------
> # /etc/ax25/nrbroadcast
> #
> # The format of this file is:
> #
> # ax25_name min_obs def_qual worst_qual verbose
> #
> pk96 5 250 100 0
>
> axports-----------
> # /etc/ax25/axports
> #
> # The format of this file is:
> #
> # name callsign speed paclen window description
> #
> pk96 wr7vhf 19200 255 4 BackBone Port
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-
> hams" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
John Ronan <jronan@tssg.org>, +353-51-302938
Telecommunications Software & Systems Group, http://www.tssg.org
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Linux NetRom Node Question
2009-10-04 19:32 ` John Ronan
@ 2009-10-05 4:32 ` Jeremiah
0 siblings, 0 replies; 6+ messages in thread
From: Jeremiah @ 2009-10-05 4:32 UTC (permalink / raw)
To: John Ronan; +Cc: linux-hams
Hello,
Thanks for the Reply John.
I have tried just has you showed and I get the "NET/ROM port netrom bound to
device nr0". But when I if ifconfig nr0 it does not have the node call after
the HWaddr.
I'm running OpenSuse 11.1 below is the out put of uname.
Linux wr7vhf-rms 2.6.27.25-0.1-pae #1 SMP 2009-07-01 15:37:09 +0200 i686 i686
i386 GNU/Linux
That is really the only glitch I'm running into is that the nr0 port neve
attaches to the call for the node.
Thanks
Jeremiah
KD7DMP
On Sunday 04 October 2009 12:32:21 John Ronan wrote:
> Hi,
>
> I don't use netrom as it was causing segfaults at one stage and as no
> one around here uses netrom anymore I stopped.
>
> however just out of curiosity I had a look
>
> firstly
> modprobe netrom
> then
> root@ns1:~# cat /etc/ax25/nrports
> # /etc/ax25/nrports
> #
> # The format of this file is:
> #
> # name callsign alias paclen description
> #
> netrom EI7IG-14 #TMRE 235 Switch Port
> netnod EI7IG-1 TMRE 235 Node
> root@ns1:~# nrattach -i 44.155.6.12 -m 236 netrom
> NET/ROM port netrom bound to device nr0
> root@ns1:~# ifconfig nr0
> nr0 Link encap:AMPR NET/ROM HWaddr EI7IG-14
> inet addr:44.155.6.12 Mask:255.0.0.0
> UP RUNNING NOARP MTU:236 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>
> root@ns1:~#
>
> Regards
> de John
> EI7IG
>
> On 4 Oct 2009, at 19:46, Jeremiah wrote:
> > Hello all,
> >
> > I am still working on setting up our RMS to send out NetRom
> > Broadcasts. I have
> > added a "dummy" entry into the nrports file for connection outbound
> > from the
> > node. I also corrected the entry for the RMS. Running nrattach it
> > comes back
> > with "NET/ROM port winl2k bound to device nr0", but it never shows
> > up when I
> > run ifconfig. There are no errors in the system logs when I run
> > nrattach.
> > Does anyone have an example nrports file they would be willing to
> > share? I'm
> > a bit stuck on this because the nr0 interface does not come up and
> > the system
> > gives me no errors in /var/log/messages.
> >
> >
> >
> > Thanks
> >
> > Jeremiah
> > KD7DMP
> >
> > nrports-------------
> > # /etc/ax25/nrports
> > #
> > # The format of this file is:
> > #
> > # name callsign alias paclen description
> > #
> > switch WR7VHF-14 #WINL2k 235 dummy for the RMS
> > winl2k WR7VHF-10 WINL2K 235 RMS
> >
> > nrbroadcast------------
> > # /etc/ax25/nrbroadcast
> > #
> > # The format of this file is:
> > #
> > # ax25_name min_obs def_qual worst_qual verbose
> > #
> > pk96 5 250 100 0
> >
> > axports-----------
> > # /etc/ax25/axports
> > #
> > # The format of this file is:
> > #
> > # name callsign speed paclen window description
> > #
> > pk96 wr7vhf 19200 255 4 BackBone Port
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-
> > hams" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
>
> --
> John Ronan <jronan@tssg.org>, +353-51-302938
> Telecommunications Software & Systems Group, http://www.tssg.org
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Linux NetRom Node Question
2009-09-27 0:12 ` Ray Wells
@ 2009-09-27 6:54 ` Jeremiah
0 siblings, 0 replies; 6+ messages in thread
From: Jeremiah @ 2009-09-27 6:54 UTC (permalink / raw)
To: Ray Wells; +Cc: linux-hams
I guess I did forget that part.
Yes I have loaded the netrom module.
On Saturday 26 September 2009 17:12:21 Ray Wells wrote:
> Just to clarify a point, have you loaded the netrom module?
>
> Ray vk2tv
>
> Jeremiah wrote:
> > Hello all,
> >
> > I have been working on setting up a RMS WinLink2000 gateway on Linux for
> > our local club. I wanted to set the box up to send out NetRom Broadcasts
> > so it would so up on the node list on all the local nodes. I have setup
> > the nrports and nrbroadcast files up per the man pages(see config files
> > below), but when I run the nrattach command I can't get it to bring up
> > the nr0 interface. It gives me no errors when I run nrattach, but when I
> > cat /proc/net/nr_nodes afterwards I see no node info. Also if I ifconfig
> > nr0 after running nrattach it shows up with no callsign.
> > Is there something I'm missing?
> >
> > The box is running openSuse 11.1 with the 2.6.27.25-0.1-pae kernel.
> >
> > Thanks all and 73's
> >
> > Jeremiah Puhek
> > KD7DMP
> > -------------------------
> > uname -a
> > Linux wr7vhf-rms 2.6.27.25-0.1-pae #1 SMP 2009-07-01 15:37:09 +0200 i686
> > i686 i386 GNU/Linux
> > ------------------------------------
> > # /etc/ax25/nrbroadcast
> > #
> > # The format of this file is:
> > #
> > # ax25_name min_obs def_qual worst_qual verbose
> > #
> > pk96 10 192 100 1
> >
> > ---------------------------------------
> > # /etc/ax25/nrports
> > #
> > # The format of this file is:
> > #
> > # name callsign alias paclen description
> > #
> > winl2k WR7VHF WINL2k 236 node for the RMS
> >
> > ----------------------------------------
> > # /etc/ax25/axports
> > #
> > # The format of this file is:
> > #
> > # name callsign speed paclen window description
> > #
> > pk96 wr7vhf 19200 255 4 BackBone Port
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-hams" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-hams" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Linux NetRom Node Question
2009-09-26 23:35 Jeremiah
@ 2009-09-27 0:12 ` Ray Wells
2009-09-27 6:54 ` Jeremiah
0 siblings, 1 reply; 6+ messages in thread
From: Ray Wells @ 2009-09-27 0:12 UTC (permalink / raw)
To: Jeremiah; +Cc: linux-hams
Just to clarify a point, have you loaded the netrom module?
Ray vk2tv
Jeremiah wrote:
> Hello all,
>
> I have been working on setting up a RMS WinLink2000 gateway on Linux for our
> local club. I wanted to set the box up to send out NetRom Broadcasts so it
> would so up on the node list on all the local nodes. I have setup the nrports
> and nrbroadcast files up per the man pages(see config files below), but when
> I run the nrattach command I can't get it to bring up the nr0 interface. It
> gives me no errors when I run nrattach, but when I cat /proc/net/nr_nodes
> afterwards I see no node info. Also if I ifconfig nr0 after running nrattach
> it shows up with no callsign.
> Is there something I'm missing?
>
> The box is running openSuse 11.1 with the 2.6.27.25-0.1-pae kernel.
>
> Thanks all and 73's
>
> Jeremiah Puhek
> KD7DMP
> -------------------------
> uname -a
> Linux wr7vhf-rms 2.6.27.25-0.1-pae #1 SMP 2009-07-01 15:37:09 +0200 i686 i686
> i386 GNU/Linux
> ------------------------------------
> # /etc/ax25/nrbroadcast
> #
> # The format of this file is:
> #
> # ax25_name min_obs def_qual worst_qual verbose
> #
> pk96 10 192 100 1
>
> ---------------------------------------
> # /etc/ax25/nrports
> #
> # The format of this file is:
> #
> # name callsign alias paclen description
> #
> winl2k WR7VHF WINL2k 236 node for the RMS
>
> ----------------------------------------
> # /etc/ax25/axports
> #
> # The format of this file is:
> #
> # name callsign speed paclen window description
> #
> pk96 wr7vhf 19200 255 4 BackBone Port
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-hams" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Linux NetRom Node Question
@ 2009-09-26 23:35 Jeremiah
2009-09-27 0:12 ` Ray Wells
0 siblings, 1 reply; 6+ messages in thread
From: Jeremiah @ 2009-09-26 23:35 UTC (permalink / raw)
To: linux-hams
Hello all,
I have been working on setting up a RMS WinLink2000 gateway on Linux for our
local club. I wanted to set the box up to send out NetRom Broadcasts so it
would so up on the node list on all the local nodes. I have setup the nrports
and nrbroadcast files up per the man pages(see config files below), but when
I run the nrattach command I can't get it to bring up the nr0 interface. It
gives me no errors when I run nrattach, but when I cat /proc/net/nr_nodes
afterwards I see no node info. Also if I ifconfig nr0 after running nrattach
it shows up with no callsign.
Is there something I'm missing?
The box is running openSuse 11.1 with the 2.6.27.25-0.1-pae kernel.
Thanks all and 73's
Jeremiah Puhek
KD7DMP
-------------------------
uname -a
Linux wr7vhf-rms 2.6.27.25-0.1-pae #1 SMP 2009-07-01 15:37:09 +0200 i686 i686
i386 GNU/Linux
------------------------------------
# /etc/ax25/nrbroadcast
#
# The format of this file is:
#
# ax25_name min_obs def_qual worst_qual verbose
#
pk96 10 192 100 1
---------------------------------------
# /etc/ax25/nrports
#
# The format of this file is:
#
# name callsign alias paclen description
#
winl2k WR7VHF WINL2k 236 node for the RMS
----------------------------------------
# /etc/ax25/axports
#
# The format of this file is:
#
# name callsign speed paclen window description
#
pk96 wr7vhf 19200 255 4 BackBone Port
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2009-10-05 4:32 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2009-10-04 18:46 Linux NetRom Node Question Jeremiah
2009-10-04 19:32 ` John Ronan
2009-10-05 4:32 ` Jeremiah
-- strict thread matches above, loose matches on Subject: below --
2009-09-26 23:35 Jeremiah
2009-09-27 0:12 ` Ray Wells
2009-09-27 6:54 ` Jeremiah
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.