* [U-Boot] [PATCH] mpc8308_p1m: support for MPC8308 P1M board
@ 2010-08-25 14:00 Ilya Yanok
2010-09-06 10:32 ` [U-Boot] [PATCH][v2] " Ilya Yanok
0 siblings, 1 reply; 23+ messages in thread
From: Ilya Yanok @ 2010-08-25 14:00 UTC (permalink / raw)
To: u-boot
This patch provides support for MPC8308 P1M board with the following
set of features:
Dual UART is supported
NOR flash is supported
Both TSEC Ethernet controllers are supported
PCI Express initialization is supported
Both I2C controllers are supported
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
MAINTAINERS | 1 +
board/mpc8308_p1m/Makefile | 52 ++++
board/mpc8308_p1m/config.mk | 1 +
board/mpc8308_p1m/mpc8308_p1m.c | 122 +++++++++
board/mpc8308_p1m/sdram.c | 126 +++++++++
boards.cfg | 1 +
include/configs/mpc8308_p1m.h | 548 +++++++++++++++++++++++++++++++++++++++
7 files changed, 851 insertions(+), 0 deletions(-)
create mode 100644 board/mpc8308_p1m/Makefile
create mode 100644 board/mpc8308_p1m/config.mk
create mode 100644 board/mpc8308_p1m/mpc8308_p1m.c
create mode 100644 board/mpc8308_p1m/sdram.c
create mode 100644 include/configs/mpc8308_p1m.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 4b91b0f..e28632a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -490,6 +490,7 @@ Stephen Williams <steve@icarus.com>
Ilya Yanok <yanok@emcraft.com>
+ mpc8308_p1m MPC8308
MPC8308RDB MPC8308
Roy Zang <tie-fei.zang@freescale.com>
diff --git a/board/mpc8308_p1m/Makefile b/board/mpc8308_p1m/Makefile
new file mode 100644
index 0000000..e9bfa2b
--- /dev/null
+++ b/board/mpc8308_p1m/Makefile
@@ -0,0 +1,52 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+# (C) Copyright 2010
+# Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o sdram.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/mpc8308_p1m/config.mk b/board/mpc8308_p1m/config.mk
new file mode 100644
index 0000000..1591df5
--- /dev/null
+++ b/board/mpc8308_p1m/config.mk
@@ -0,0 +1 @@
+TEXT_BASE = 0xFC000000
diff --git a/board/mpc8308_p1m/mpc8308_p1m.c b/board/mpc8308_p1m/mpc8308_p1m.c
new file mode 100644
index 0000000..ba144d3
--- /dev/null
+++ b/board/mpc8308_p1m/mpc8308_p1m.c
@@ -0,0 +1,122 @@
+/*
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_mpc83xx_serdes.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+
+ if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
+ gd->flags |= GD_FLG_SILENT;
+
+ /* initialized GPIO default directions and values */
+ __raw_writel(CONFIG_GPIO_PDAT, &im->gpio[0].dat);
+ __raw_writel(CONFIG_GPIO_PDIR, &im->gpio[0].dir);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ printf("Board: MPC8308 P1M\n");
+
+ return 0;
+}
+
+static struct pci_region pcie_regions_0[] = {
+ {
+ .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+ .size = CONFIG_SYS_PCIE1_MEM_SIZE,
+ .flags = PCI_REGION_MEM,
+ },
+ {
+ .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+ .size = CONFIG_SYS_PCIE1_IO_SIZE,
+ .flags = PCI_REGION_IO,
+ },
+};
+
+void pci_init_board(void)
+{
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+ sysconf83xx_t *sysconf = &immr->sysconf;
+ clk83xx_t *clk = (clk83xx_t *)&immr->clk;
+ law83xx_t *pcie_law = sysconf->pcielaw;
+ struct pci_region *pcie_reg[] = { pcie_regions_0 };
+
+ fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
+ FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+ clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM ,
+ SCCR_PCIEXP1CM_1);
+
+ /* Deassert the resets in the control register */
+ out_be32(&sysconf->pecr1, 0xE0008000);
+ udelay(2000);
+
+ /* Configure PCI Express Local Access Windows */
+ out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+ out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+ mpc83xx_pcie_init(1, pcie_reg, 0);
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+ fdt_fixup_dr_usb(blob, bd);
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rv, num_if = 0;
+
+ /* Initialize TSECs first */
+ if ((rv = cpu_eth_init(bis)) >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize TSECs.\n");
+
+ if ((rv = pci_eth_init(bis)) >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize PCI Ethernet.\n");
+
+ return num_if;
+}
diff --git a/board/mpc8308_p1m/sdram.c b/board/mpc8308_p1m/sdram.c
new file mode 100644
index 0000000..939c1b8
--- /dev/null
+++ b/board/mpc8308_p1m/sdram.c
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ * Authors: Nick.Spence at freescale.com
+ * Wilson.Lo at freescale.com
+ * scottwood at freescale.com
+ *
+ * This files is mostly identical to the original from
+ * board\freescale\mpc8315erdb\sdram.c
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void resume_from_sleep(void)
+{
+ u32 magic = *(u32 *)0;
+
+ typedef void (*func_t)(void);
+ func_t resume = *(func_t *)4;
+
+ if (magic == 0xf5153ae5)
+ resume();
+
+ gd->flags &= ~GD_FLG_SILENT;
+ puts("\nResume from sleep failed: bad magic word\n");
+}
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+ u32 msize_log2 = __ilog2(msize);
+
+ out_be32(&im->sysconf.ddrlaw[0].bar,
+ CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000);
+ out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
+ out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+ /*
+ * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+ * or the DDR2 controller may fail to initialize correctly.
+ */
+ udelay(50000);
+
+ out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+ out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
+
+ /* Currently we use only one CS, so disable the other bank. */
+ out_be32(&im->ddr.cs_config[1], 0);
+
+ out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL);
+ out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+ if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF) {
+ out_be32(&im->ddr.sdram_cfg,
+ CONFIG_SYS_DDR_SDRAM_CFG | SDRAM_CFG_BI);
+ } else {
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
+ }
+
+ out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
+ out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+ out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
+
+ out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ sync();
+
+ /* enable DDR controller */
+ setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+ sync();
+
+ return get_ram_size(CONFIG_SYS_DDR_SDRAM_BASE, msize);
+}
+
+phys_size_t initdram(int board_type)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize;
+
+ if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ /* DDR SDRAM */
+ msize = fixed_sdram();
+
+ if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
+ resume_from_sleep();
+
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize;
+}
diff --git a/boards.cfg b/boards.cfg
index 69c6897..4712fb0 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -333,6 +333,7 @@ ppmc8260 powerpc mpc8260
RPXsuper powerpc mpc8260 rpxsuper
rsdproto powerpc mpc8260
MPC8266ADS powerpc mpc8260 mpc8266ads freescale
+mpc8308_p1m powerpc mpc83xx
MPC8308RDB powerpc mpc83xx mpc8308rdb freescale
MPC8323ERDB powerpc mpc83xx mpc8323erdb freescale
MPC8349EMDS powerpc mpc83xx mpc8349emds freescale
diff --git a/include/configs/mpc8308_p1m.h b/include/configs/mpc8308_p1m.h
new file mode 100644
index 0000000..76b8281
--- /dev/null
+++ b/include/configs/mpc8308_p1m.h
@@ -0,0 +1,548 @@
+/*
+ * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_MPC83xx 1 /* MPC83xx family */
+#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
+#define CONFIG_MPC8308_P1M 1 /* mpc8308_p1m board specific */
+
+/*
+ * On-board devices
+ *
+ * TSECs
+ */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC2
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.66MHz, then
+ * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
+ * We choose the A type silicon as default, so the core is 400Mhz.
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_SVCOD_DIV_2 |\
+ HRCWL_CSB_TO_CLKIN_4X1 |\
+ HRCWL_CORE_TO_CSB_3X1)
+/*
+ * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
+ * in 8308's HRCWH according to the manual, but original Freescale's
+ * code has them and I've expirienced some problems using the board
+ * with BDI3000 attached when I've tried to set these bits to zero
+ * (UART doesn't work after the 'reset run' command).
+ */
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_RL_EXT_LEGACY |\
+ HRCWH_TSEC1M_IN_MII |\
+ HRCWH_TSEC2M_IN_MII |\
+ HRCWH_BIG_ENDIAN)
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRH 0xf577d100
+#define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */
+
+/* GPIO Default input/output settings */
+#define CONFIG_GPIO_PDIR 0x7AAF8C00
+/*
+ * Default GPIO values:
+ * LED#1 enabled; WLAN enabled; Both COM LED on (orange)
+ */
+#define CONFIG_GPIO_PDAT 0x08008C00
+
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+
+/*
+ * IMMR new address
+ */
+#define CONFIG_SYS_IMMR 0xE0000000
+
+/*
+ * SERDES
+ */
+#define CONFIG_FSL_SERDES
+#define CONFIG_FSL_SERDES1 0xe3000
+
+/*
+ * Arbiter Setup
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
+#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
+ | DDRCDR_PZ_LOZ \
+ | DDRCDR_NZ_LOZ \
+ | DDRCDR_ODT \
+ | DDRCDR_Q_DRN)
+ /* 0x7b880001 */
+/*
+ * Manually set up DDR parameters
+ * consist of two chips HY5PS12621BFP-C4 from HYNIX
+ */
+
+#define CONFIG_SYS_DDR_SIZE 128 /* MB */
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
+ | 0x00010000 /* ODT_WR to CSn */ \
+ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+ /* 0x80010102 */
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
+ | (0 << TIMING_CFG0_WRT_SHIFT) \
+ | (0 << TIMING_CFG0_RRT_SHIFT) \
+ | (0 << TIMING_CFG0_WWT_SHIFT) \
+ | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
+ | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+ /* 0x00220802 */
+#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
+ | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
+ | (5 << TIMING_CFG1_CASLAT_SHIFT) \
+ | (6 << TIMING_CFG1_REFREC_SHIFT) \
+ | (2 << TIMING_CFG1_WRREC_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
+ | (2 << TIMING_CFG1_WRTORD_SHIFT))
+ /* 0x27256222 */
+#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
+ | (4 << TIMING_CFG2_CPO_SHIFT) \
+ | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
+ | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
+ | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
+ | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
+ | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
+ /* 0x121048c5 */
+#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
+ | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+ /* 0x03600100 */
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
+ | SDRAM_CFG_SDRAM_TYPE_DDR2 \
+ | SDRAM_CFG_32_BE)
+ /* 0x43080000 */
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
+#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
+ | (0x0232 << SDRAM_MODE_SD_SHIFT))
+ /* ODT 150ohm CL=3, AL=1 on SDRAM */
+#define CONFIG_SYS_DDR_MODE2 0x00000000
+
+/*
+ * Memory test
+ */
+#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x07f00000
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR 0x00040000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+
+#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
+
+/* Window base@flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000019 /* 64MB window size */
+
+#define CONFIG_SYS_BR0_PRELIM (\
+ CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\
+ (2 << BR_PS_SHIFT) /* 16 bit port size */ |\
+ BR_V) /* valid */
+#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \
+ | OR_UPM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_4 \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512
+
+/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024)
+/* Flash Write Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024)
+
+/*
+ * SJA1000 CAN controller on Local Bus
+ */
+#define CONFIG_SYS_SJA1000_BASE 0xFBFF0000
+#define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_SJA1000_BASE \
+ | (1 << BR_PS_SHIFT) /* 8 bit port size */ \
+ | BR_V ) /* valid */
+#define CONFIG_SYS_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_GPCM_SCY_5 \
+ | OR_GPCM_EHTR)
+ /* 0xFFFF8052 */
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+
+/*
+ * CPLD on Local Bus
+ */
+#define CONFIG_SYS_CPLD_BASE 0xFBFF8000
+#define CONFIG_SYS_BR2_PRELIM ( CONFIG_SYS_CPLD_BASE \
+ | (1 << BR_PS_SHIFT) /* 8 bit port size */ \
+ | BR_V ) /* valid */
+#define CONFIG_SYS_OR2_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_GPCM_SCY_4 \
+ | OR_GPCM_EHTR)
+ /* 0xFFFF8042 */
+
+#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM 0x8000000E /* 32KB */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCIE1_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
+#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
+#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
+#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
+
+/*
+ * Fake PCIE2 definitions: there is no PCIE2 on this board but the code
+ * in arch/powerpc/cpu/mpc83xx/pcie.c doesn't compile without this
+ */
+#define CONFIG_SYS_PCIE2_BASE 0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
+#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000
+#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000
+#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
+
+#define CONFIG_PCI
+#define CONFIG_PCIE
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
+
+/*
+ * TSEC
+ */
+#define CONFIG_NET_MULTI
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
+
+/*
+ * TSEC ethernet configuration
+ */
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_TSEC1_NAME "eTSEC0"
+#define CONFIG_TSEC2_NAME "eTSEC1"
+#define TSEC1_PHY_ADDR 1
+#define TSEC2_PHY_ADDR 2
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS 0
+#define TSEC2_FLAGS 0
+
+/* Options are: eTSEC[0-1] */
+#define CONFIG_ETHPRIME "eTSEC0"
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
+ CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+ HID0_ENABLE_INSTRUCTION_CACHE | \
+ HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
+#define CONFIG_SYS_HID2 HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+
+/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
+ BATU_VP)
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | \
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
+
+#define xstr(s) str(s)
+#define str(s) #s
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs}" \
+ " console=${consoledev},${baudrate}\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addmisc=setenv bootargs ${bootargs}\0" \
+ "kernel_addr=FC080000\0" \
+ "fdt_addr=FC280000\0" \
+ "ramdisk_addr=FC290000\0" \
+ "u-boot=mpc8308_p1m/u-boot.bin\0" \
+ "kernel_addr_r=1000000\0" \
+ "fdt_addr_r=C00000\0" \
+ "hostname=mpc8308_p1m\0" \
+ "bootfile=mpc8308_p1m/uImage\0" \
+ "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \
+ "rootpath=/opt/eldk-4.2/ppc_6xx\0" \
+ "flash_self=run ramargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
+ "tftp ${fdt_addr_r} ${fdtfile};" \
+ "run nfsargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
+ "bootcmd=run flash_self\0" \
+ "load=tftp ${loadaddr} ${u-boot}\0" \
+ "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};cp.b ${fileaddr} " \
+ xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
+ "upd=run load update\0" \
+
+#endif /* __CONFIG_H */
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH][v2] mpc8308_p1m: support for MPC8308 P1M board
2010-08-25 14:00 [U-Boot] [PATCH] mpc8308_p1m: support for MPC8308 P1M board Ilya Yanok
@ 2010-09-06 10:32 ` Ilya Yanok
2010-09-07 21:47 ` Scott Wood
0 siblings, 1 reply; 23+ messages in thread
From: Ilya Yanok @ 2010-09-06 10:32 UTC (permalink / raw)
To: u-boot
This patch provides support for MPC8308 P1M board with the following
set of features:
Dual UART is supported
NOR flash is supported
Both TSEC Ethernet controllers are supported
PCI Express initialization is supported
Both I2C controllers are supported
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
Changes from previous version: corrected kernel_addr, fdt_addr and
ramdisk_addr values in default environment.
MAINTAINERS | 1 +
board/mpc8308_p1m/Makefile | 52 ++++
board/mpc8308_p1m/config.mk | 1 +
board/mpc8308_p1m/mpc8308_p1m.c | 122 +++++++++
board/mpc8308_p1m/sdram.c | 126 +++++++++
boards.cfg | 1 +
include/configs/mpc8308_p1m.h | 548 +++++++++++++++++++++++++++++++++++++++
7 files changed, 851 insertions(+), 0 deletions(-)
create mode 100644 board/mpc8308_p1m/Makefile
create mode 100644 board/mpc8308_p1m/config.mk
create mode 100644 board/mpc8308_p1m/mpc8308_p1m.c
create mode 100644 board/mpc8308_p1m/sdram.c
create mode 100644 include/configs/mpc8308_p1m.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 4b91b0f..e28632a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -490,6 +490,7 @@ Stephen Williams <steve@icarus.com>
Ilya Yanok <yanok@emcraft.com>
+ mpc8308_p1m MPC8308
MPC8308RDB MPC8308
Roy Zang <tie-fei.zang@freescale.com>
diff --git a/board/mpc8308_p1m/Makefile b/board/mpc8308_p1m/Makefile
new file mode 100644
index 0000000..e9bfa2b
--- /dev/null
+++ b/board/mpc8308_p1m/Makefile
@@ -0,0 +1,52 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+# (C) Copyright 2010
+# Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o sdram.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/mpc8308_p1m/config.mk b/board/mpc8308_p1m/config.mk
new file mode 100644
index 0000000..1591df5
--- /dev/null
+++ b/board/mpc8308_p1m/config.mk
@@ -0,0 +1 @@
+TEXT_BASE = 0xFC000000
diff --git a/board/mpc8308_p1m/mpc8308_p1m.c b/board/mpc8308_p1m/mpc8308_p1m.c
new file mode 100644
index 0000000..ba144d3
--- /dev/null
+++ b/board/mpc8308_p1m/mpc8308_p1m.c
@@ -0,0 +1,122 @@
+/*
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_mpc83xx_serdes.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+
+ if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
+ gd->flags |= GD_FLG_SILENT;
+
+ /* initialized GPIO default directions and values */
+ __raw_writel(CONFIG_GPIO_PDAT, &im->gpio[0].dat);
+ __raw_writel(CONFIG_GPIO_PDIR, &im->gpio[0].dir);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ printf("Board: MPC8308 P1M\n");
+
+ return 0;
+}
+
+static struct pci_region pcie_regions_0[] = {
+ {
+ .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+ .size = CONFIG_SYS_PCIE1_MEM_SIZE,
+ .flags = PCI_REGION_MEM,
+ },
+ {
+ .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+ .size = CONFIG_SYS_PCIE1_IO_SIZE,
+ .flags = PCI_REGION_IO,
+ },
+};
+
+void pci_init_board(void)
+{
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+ sysconf83xx_t *sysconf = &immr->sysconf;
+ clk83xx_t *clk = (clk83xx_t *)&immr->clk;
+ law83xx_t *pcie_law = sysconf->pcielaw;
+ struct pci_region *pcie_reg[] = { pcie_regions_0 };
+
+ fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
+ FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+ clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM ,
+ SCCR_PCIEXP1CM_1);
+
+ /* Deassert the resets in the control register */
+ out_be32(&sysconf->pecr1, 0xE0008000);
+ udelay(2000);
+
+ /* Configure PCI Express Local Access Windows */
+ out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+ out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+ mpc83xx_pcie_init(1, pcie_reg, 0);
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+ fdt_fixup_dr_usb(blob, bd);
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rv, num_if = 0;
+
+ /* Initialize TSECs first */
+ if ((rv = cpu_eth_init(bis)) >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize TSECs.\n");
+
+ if ((rv = pci_eth_init(bis)) >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize PCI Ethernet.\n");
+
+ return num_if;
+}
diff --git a/board/mpc8308_p1m/sdram.c b/board/mpc8308_p1m/sdram.c
new file mode 100644
index 0000000..939c1b8
--- /dev/null
+++ b/board/mpc8308_p1m/sdram.c
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ * Authors: Nick.Spence at freescale.com
+ * Wilson.Lo at freescale.com
+ * scottwood at freescale.com
+ *
+ * This files is mostly identical to the original from
+ * board\freescale\mpc8315erdb\sdram.c
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void resume_from_sleep(void)
+{
+ u32 magic = *(u32 *)0;
+
+ typedef void (*func_t)(void);
+ func_t resume = *(func_t *)4;
+
+ if (magic == 0xf5153ae5)
+ resume();
+
+ gd->flags &= ~GD_FLG_SILENT;
+ puts("\nResume from sleep failed: bad magic word\n");
+}
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+ u32 msize_log2 = __ilog2(msize);
+
+ out_be32(&im->sysconf.ddrlaw[0].bar,
+ CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000);
+ out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
+ out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+ /*
+ * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+ * or the DDR2 controller may fail to initialize correctly.
+ */
+ udelay(50000);
+
+ out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+ out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
+
+ /* Currently we use only one CS, so disable the other bank. */
+ out_be32(&im->ddr.cs_config[1], 0);
+
+ out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL);
+ out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+ if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF) {
+ out_be32(&im->ddr.sdram_cfg,
+ CONFIG_SYS_DDR_SDRAM_CFG | SDRAM_CFG_BI);
+ } else {
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
+ }
+
+ out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
+ out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+ out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
+
+ out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ sync();
+
+ /* enable DDR controller */
+ setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+ sync();
+
+ return get_ram_size(CONFIG_SYS_DDR_SDRAM_BASE, msize);
+}
+
+phys_size_t initdram(int board_type)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize;
+
+ if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ /* DDR SDRAM */
+ msize = fixed_sdram();
+
+ if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
+ resume_from_sleep();
+
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize;
+}
diff --git a/boards.cfg b/boards.cfg
index 69c6897..4712fb0 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -333,6 +333,7 @@ ppmc8260 powerpc mpc8260
RPXsuper powerpc mpc8260 rpxsuper
rsdproto powerpc mpc8260
MPC8266ADS powerpc mpc8260 mpc8266ads freescale
+mpc8308_p1m powerpc mpc83xx
MPC8308RDB powerpc mpc83xx mpc8308rdb freescale
MPC8323ERDB powerpc mpc83xx mpc8323erdb freescale
MPC8349EMDS powerpc mpc83xx mpc8349emds freescale
diff --git a/include/configs/mpc8308_p1m.h b/include/configs/mpc8308_p1m.h
new file mode 100644
index 0000000..da3f133
--- /dev/null
+++ b/include/configs/mpc8308_p1m.h
@@ -0,0 +1,548 @@
+/*
+ * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_MPC83xx 1 /* MPC83xx family */
+#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
+#define CONFIG_MPC8308_P1M 1 /* mpc8308_p1m board specific */
+
+/*
+ * On-board devices
+ *
+ * TSECs
+ */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC2
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.66MHz, then
+ * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
+ * We choose the A type silicon as default, so the core is 400Mhz.
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_SVCOD_DIV_2 |\
+ HRCWL_CSB_TO_CLKIN_4X1 |\
+ HRCWL_CORE_TO_CSB_3X1)
+/*
+ * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
+ * in 8308's HRCWH according to the manual, but original Freescale's
+ * code has them and I've expirienced some problems using the board
+ * with BDI3000 attached when I've tried to set these bits to zero
+ * (UART doesn't work after the 'reset run' command).
+ */
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_RL_EXT_LEGACY |\
+ HRCWH_TSEC1M_IN_MII |\
+ HRCWH_TSEC2M_IN_MII |\
+ HRCWH_BIG_ENDIAN)
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRH 0xf577d100
+#define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */
+
+/* GPIO Default input/output settings */
+#define CONFIG_GPIO_PDIR 0x7AAF8C00
+/*
+ * Default GPIO values:
+ * LED#1 enabled; WLAN enabled; Both COM LED on (orange)
+ */
+#define CONFIG_GPIO_PDAT 0x08008C00
+
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+
+/*
+ * IMMR new address
+ */
+#define CONFIG_SYS_IMMR 0xE0000000
+
+/*
+ * SERDES
+ */
+#define CONFIG_FSL_SERDES
+#define CONFIG_FSL_SERDES1 0xe3000
+
+/*
+ * Arbiter Setup
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
+#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
+ | DDRCDR_PZ_LOZ \
+ | DDRCDR_NZ_LOZ \
+ | DDRCDR_ODT \
+ | DDRCDR_Q_DRN)
+ /* 0x7b880001 */
+/*
+ * Manually set up DDR parameters
+ * consist of two chips HY5PS12621BFP-C4 from HYNIX
+ */
+
+#define CONFIG_SYS_DDR_SIZE 128 /* MB */
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
+ | 0x00010000 /* ODT_WR to CSn */ \
+ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+ /* 0x80010102 */
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
+ | (0 << TIMING_CFG0_WRT_SHIFT) \
+ | (0 << TIMING_CFG0_RRT_SHIFT) \
+ | (0 << TIMING_CFG0_WWT_SHIFT) \
+ | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
+ | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+ /* 0x00220802 */
+#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
+ | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
+ | (5 << TIMING_CFG1_CASLAT_SHIFT) \
+ | (6 << TIMING_CFG1_REFREC_SHIFT) \
+ | (2 << TIMING_CFG1_WRREC_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
+ | (2 << TIMING_CFG1_WRTORD_SHIFT))
+ /* 0x27256222 */
+#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
+ | (4 << TIMING_CFG2_CPO_SHIFT) \
+ | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
+ | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
+ | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
+ | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
+ | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
+ /* 0x121048c5 */
+#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
+ | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+ /* 0x03600100 */
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
+ | SDRAM_CFG_SDRAM_TYPE_DDR2 \
+ | SDRAM_CFG_32_BE)
+ /* 0x43080000 */
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
+#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
+ | (0x0232 << SDRAM_MODE_SD_SHIFT))
+ /* ODT 150ohm CL=3, AL=1 on SDRAM */
+#define CONFIG_SYS_DDR_MODE2 0x00000000
+
+/*
+ * Memory test
+ */
+#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x07f00000
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR 0x00040000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+
+#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
+
+/* Window base@flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000019 /* 64MB window size */
+
+#define CONFIG_SYS_BR0_PRELIM (\
+ CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\
+ (2 << BR_PS_SHIFT) /* 16 bit port size */ |\
+ BR_V) /* valid */
+#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \
+ | OR_UPM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_4 \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512
+
+/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024)
+/* Flash Write Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024)
+
+/*
+ * SJA1000 CAN controller on Local Bus
+ */
+#define CONFIG_SYS_SJA1000_BASE 0xFBFF0000
+#define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_SJA1000_BASE \
+ | (1 << BR_PS_SHIFT) /* 8 bit port size */ \
+ | BR_V ) /* valid */
+#define CONFIG_SYS_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_GPCM_SCY_5 \
+ | OR_GPCM_EHTR)
+ /* 0xFFFF8052 */
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+
+/*
+ * CPLD on Local Bus
+ */
+#define CONFIG_SYS_CPLD_BASE 0xFBFF8000
+#define CONFIG_SYS_BR2_PRELIM ( CONFIG_SYS_CPLD_BASE \
+ | (1 << BR_PS_SHIFT) /* 8 bit port size */ \
+ | BR_V ) /* valid */
+#define CONFIG_SYS_OR2_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_GPCM_SCY_4 \
+ | OR_GPCM_EHTR)
+ /* 0xFFFF8042 */
+
+#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM 0x8000000E /* 32KB */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCIE1_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
+#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
+#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
+#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
+
+/*
+ * Fake PCIE2 definitions: there is no PCIE2 on this board but the code
+ * in arch/powerpc/cpu/mpc83xx/pcie.c doesn't compile without this
+ */
+#define CONFIG_SYS_PCIE2_BASE 0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
+#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000
+#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000
+#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
+
+#define CONFIG_PCI
+#define CONFIG_PCIE
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
+
+/*
+ * TSEC
+ */
+#define CONFIG_NET_MULTI
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
+
+/*
+ * TSEC ethernet configuration
+ */
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_TSEC1_NAME "eTSEC0"
+#define CONFIG_TSEC2_NAME "eTSEC1"
+#define TSEC1_PHY_ADDR 1
+#define TSEC2_PHY_ADDR 2
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS 0
+#define TSEC2_FLAGS 0
+
+/* Options are: eTSEC[0-1] */
+#define CONFIG_ETHPRIME "eTSEC0"
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
+ CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+ HID0_ENABLE_INSTRUCTION_CACHE | \
+ HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
+#define CONFIG_SYS_HID2 HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+
+/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
+ BATU_VP)
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | \
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
+
+#define xstr(s) str(s)
+#define str(s) #s
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs}" \
+ " console=${consoledev},${baudrate}\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addmisc=setenv bootargs ${bootargs}\0" \
+ "kernel_addr=FC0A0000\0" \
+ "fdt_addr=FC2A0000\0" \
+ "ramdisk_addr=FC2C0000\0" \
+ "u-boot=mpc8308_p1m/u-boot.bin\0" \
+ "kernel_addr_r=1000000\0" \
+ "fdt_addr_r=C00000\0" \
+ "hostname=mpc8308_p1m\0" \
+ "bootfile=mpc8308_p1m/uImage\0" \
+ "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \
+ "rootpath=/opt/eldk-4.2/ppc_6xx\0" \
+ "flash_self=run ramargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
+ "tftp ${fdt_addr_r} ${fdtfile};" \
+ "run nfsargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
+ "bootcmd=run flash_self\0" \
+ "load=tftp ${loadaddr} ${u-boot}\0" \
+ "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};cp.b ${fileaddr} " \
+ xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
+ "upd=run load update\0" \
+
+#endif /* __CONFIG_H */
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH][v2] mpc8308_p1m: support for MPC8308 P1M board
2010-09-06 10:32 ` [U-Boot] [PATCH][v2] " Ilya Yanok
@ 2010-09-07 21:47 ` Scott Wood
2010-09-08 21:36 ` [U-Boot] [PATCH][v3] " Ilya Yanok
0 siblings, 1 reply; 23+ messages in thread
From: Scott Wood @ 2010-09-07 21:47 UTC (permalink / raw)
To: u-boot
On Mon, 6 Sep 2010 12:32:52 +0200
Ilya Yanok <yanok@emcraft.com> wrote:
> +static void resume_from_sleep(void)
> +{
> + u32 magic = *(u32 *)0;
> +
> + typedef void (*func_t)(void);
> + func_t resume = *(func_t *)4;
> +
> + if (magic == 0xf5153ae5)
> + resume();
> +
> + gd->flags &= ~GD_FLG_SILENT;
> + puts("\nResume from sleep failed: bad magic word\n");
> +}
8308 does not support deep sleep, so it doesn't need this function.
Likewise, PMCCR1 does not exist on 8308, so don't read it.
> +/* Fixed sdram init -- doesn't use serial presence detect.
> + *
> + * This is useful for faster booting in configs where the RAM is unlikely
> + * to be changed, or for things like NAND booting where space is tight.
> + */
> +static long fixed_sdram(void)
> +{
> + immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
> + u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
> + u32 msize_log2 = __ilog2(msize);
> +
> + out_be32(&im->sysconf.ddrlaw[0].bar,
> + CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000);
> + out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
> + out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
> +
> + /*
> + * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
> + * or the DDR2 controller may fail to initialize correctly.
> + */
> + udelay(50000);
I don't see this erratum on 8308.
-Scott
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH][v3] mpc8308_p1m: support for MPC8308 P1M board
2010-09-07 21:47 ` Scott Wood
@ 2010-09-08 21:36 ` Ilya Yanok
2010-09-14 1:12 ` Kim Phillips
0 siblings, 1 reply; 23+ messages in thread
From: Ilya Yanok @ 2010-09-08 21:36 UTC (permalink / raw)
To: u-boot
This patch provides support for MPC8308 P1M board with the following
set of features:
Dual UART is supported
NOR flash is supported
Both TSEC Ethernet controllers are supported
PCI Express initialization is supported
Both I2C controllers are supported
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
Scott's comments addressed.
MAINTAINERS | 1 +
board/mpc8308_p1m/Makefile | 52 ++++
board/mpc8308_p1m/config.mk | 1 +
board/mpc8308_p1m/mpc8308_p1m.c | 122 +++++++++
board/mpc8308_p1m/sdram.c | 93 +++++++
boards.cfg | 1 +
include/configs/mpc8308_p1m.h | 548 +++++++++++++++++++++++++++++++++++++++
7 files changed, 818 insertions(+), 0 deletions(-)
create mode 100644 board/mpc8308_p1m/Makefile
create mode 100644 board/mpc8308_p1m/config.mk
create mode 100644 board/mpc8308_p1m/mpc8308_p1m.c
create mode 100644 board/mpc8308_p1m/sdram.c
create mode 100644 include/configs/mpc8308_p1m.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 4b91b0f..e28632a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -490,6 +490,7 @@ Stephen Williams <steve@icarus.com>
Ilya Yanok <yanok@emcraft.com>
+ mpc8308_p1m MPC8308
MPC8308RDB MPC8308
Roy Zang <tie-fei.zang@freescale.com>
diff --git a/board/mpc8308_p1m/Makefile b/board/mpc8308_p1m/Makefile
new file mode 100644
index 0000000..e9bfa2b
--- /dev/null
+++ b/board/mpc8308_p1m/Makefile
@@ -0,0 +1,52 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+# (C) Copyright 2010
+# Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o sdram.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/mpc8308_p1m/config.mk b/board/mpc8308_p1m/config.mk
new file mode 100644
index 0000000..1591df5
--- /dev/null
+++ b/board/mpc8308_p1m/config.mk
@@ -0,0 +1 @@
+TEXT_BASE = 0xFC000000
diff --git a/board/mpc8308_p1m/mpc8308_p1m.c b/board/mpc8308_p1m/mpc8308_p1m.c
new file mode 100644
index 0000000..ba144d3
--- /dev/null
+++ b/board/mpc8308_p1m/mpc8308_p1m.c
@@ -0,0 +1,122 @@
+/*
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_mpc83xx_serdes.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+
+ if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
+ gd->flags |= GD_FLG_SILENT;
+
+ /* initialized GPIO default directions and values */
+ __raw_writel(CONFIG_GPIO_PDAT, &im->gpio[0].dat);
+ __raw_writel(CONFIG_GPIO_PDIR, &im->gpio[0].dir);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ printf("Board: MPC8308 P1M\n");
+
+ return 0;
+}
+
+static struct pci_region pcie_regions_0[] = {
+ {
+ .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+ .size = CONFIG_SYS_PCIE1_MEM_SIZE,
+ .flags = PCI_REGION_MEM,
+ },
+ {
+ .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+ .size = CONFIG_SYS_PCIE1_IO_SIZE,
+ .flags = PCI_REGION_IO,
+ },
+};
+
+void pci_init_board(void)
+{
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+ sysconf83xx_t *sysconf = &immr->sysconf;
+ clk83xx_t *clk = (clk83xx_t *)&immr->clk;
+ law83xx_t *pcie_law = sysconf->pcielaw;
+ struct pci_region *pcie_reg[] = { pcie_regions_0 };
+
+ fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
+ FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+ clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM ,
+ SCCR_PCIEXP1CM_1);
+
+ /* Deassert the resets in the control register */
+ out_be32(&sysconf->pecr1, 0xE0008000);
+ udelay(2000);
+
+ /* Configure PCI Express Local Access Windows */
+ out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+ out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+ mpc83xx_pcie_init(1, pcie_reg, 0);
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+ fdt_fixup_dr_usb(blob, bd);
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rv, num_if = 0;
+
+ /* Initialize TSECs first */
+ if ((rv = cpu_eth_init(bis)) >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize TSECs.\n");
+
+ if ((rv = pci_eth_init(bis)) >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize PCI Ethernet.\n");
+
+ return num_if;
+}
diff --git a/board/mpc8308_p1m/sdram.c b/board/mpc8308_p1m/sdram.c
new file mode 100644
index 0000000..a6e44e6
--- /dev/null
+++ b/board/mpc8308_p1m/sdram.c
@@ -0,0 +1,93 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ * This files is mostly identical to the original from
+ * board/freescale/mpc8308rdb/sdram.c
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+ u32 msize_log2 = __ilog2(msize);
+
+ out_be32(&im->sysconf.ddrlaw[0].bar,
+ CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000);
+ out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
+ out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+ out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+ out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
+
+ /* Currently we use only one CS, so disable the other bank. */
+ out_be32(&im->ddr.cs_config[1], 0);
+
+ out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL);
+ out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
+ out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
+ out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+ out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
+
+ out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ sync();
+
+ /* enable DDR controller */
+ setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+ sync();
+
+ return get_ram_size(CONFIG_SYS_DDR_SDRAM_BASE, msize);
+}
+
+phys_size_t initdram(int board_type)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize;
+
+ if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ /* DDR SDRAM */
+ msize = fixed_sdram();
+
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize;
+}
diff --git a/boards.cfg b/boards.cfg
index 69c6897..4712fb0 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -333,6 +333,7 @@ ppmc8260 powerpc mpc8260
RPXsuper powerpc mpc8260 rpxsuper
rsdproto powerpc mpc8260
MPC8266ADS powerpc mpc8260 mpc8266ads freescale
+mpc8308_p1m powerpc mpc83xx
MPC8308RDB powerpc mpc83xx mpc8308rdb freescale
MPC8323ERDB powerpc mpc83xx mpc8323erdb freescale
MPC8349EMDS powerpc mpc83xx mpc8349emds freescale
diff --git a/include/configs/mpc8308_p1m.h b/include/configs/mpc8308_p1m.h
new file mode 100644
index 0000000..da3f133
--- /dev/null
+++ b/include/configs/mpc8308_p1m.h
@@ -0,0 +1,548 @@
+/*
+ * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_MPC83xx 1 /* MPC83xx family */
+#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
+#define CONFIG_MPC8308_P1M 1 /* mpc8308_p1m board specific */
+
+/*
+ * On-board devices
+ *
+ * TSECs
+ */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC2
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.66MHz, then
+ * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
+ * We choose the A type silicon as default, so the core is 400Mhz.
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_SVCOD_DIV_2 |\
+ HRCWL_CSB_TO_CLKIN_4X1 |\
+ HRCWL_CORE_TO_CSB_3X1)
+/*
+ * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
+ * in 8308's HRCWH according to the manual, but original Freescale's
+ * code has them and I've expirienced some problems using the board
+ * with BDI3000 attached when I've tried to set these bits to zero
+ * (UART doesn't work after the 'reset run' command).
+ */
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_RL_EXT_LEGACY |\
+ HRCWH_TSEC1M_IN_MII |\
+ HRCWH_TSEC2M_IN_MII |\
+ HRCWH_BIG_ENDIAN)
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRH 0xf577d100
+#define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */
+
+/* GPIO Default input/output settings */
+#define CONFIG_GPIO_PDIR 0x7AAF8C00
+/*
+ * Default GPIO values:
+ * LED#1 enabled; WLAN enabled; Both COM LED on (orange)
+ */
+#define CONFIG_GPIO_PDAT 0x08008C00
+
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+
+/*
+ * IMMR new address
+ */
+#define CONFIG_SYS_IMMR 0xE0000000
+
+/*
+ * SERDES
+ */
+#define CONFIG_FSL_SERDES
+#define CONFIG_FSL_SERDES1 0xe3000
+
+/*
+ * Arbiter Setup
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
+#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
+ | DDRCDR_PZ_LOZ \
+ | DDRCDR_NZ_LOZ \
+ | DDRCDR_ODT \
+ | DDRCDR_Q_DRN)
+ /* 0x7b880001 */
+/*
+ * Manually set up DDR parameters
+ * consist of two chips HY5PS12621BFP-C4 from HYNIX
+ */
+
+#define CONFIG_SYS_DDR_SIZE 128 /* MB */
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
+ | 0x00010000 /* ODT_WR to CSn */ \
+ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+ /* 0x80010102 */
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
+ | (0 << TIMING_CFG0_WRT_SHIFT) \
+ | (0 << TIMING_CFG0_RRT_SHIFT) \
+ | (0 << TIMING_CFG0_WWT_SHIFT) \
+ | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
+ | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+ /* 0x00220802 */
+#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
+ | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
+ | (5 << TIMING_CFG1_CASLAT_SHIFT) \
+ | (6 << TIMING_CFG1_REFREC_SHIFT) \
+ | (2 << TIMING_CFG1_WRREC_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
+ | (2 << TIMING_CFG1_WRTORD_SHIFT))
+ /* 0x27256222 */
+#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
+ | (4 << TIMING_CFG2_CPO_SHIFT) \
+ | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
+ | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
+ | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
+ | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
+ | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
+ /* 0x121048c5 */
+#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
+ | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+ /* 0x03600100 */
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
+ | SDRAM_CFG_SDRAM_TYPE_DDR2 \
+ | SDRAM_CFG_32_BE)
+ /* 0x43080000 */
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
+#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
+ | (0x0232 << SDRAM_MODE_SD_SHIFT))
+ /* ODT 150ohm CL=3, AL=1 on SDRAM */
+#define CONFIG_SYS_DDR_MODE2 0x00000000
+
+/*
+ * Memory test
+ */
+#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x07f00000
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR 0x00040000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+
+#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
+
+/* Window base@flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000019 /* 64MB window size */
+
+#define CONFIG_SYS_BR0_PRELIM (\
+ CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\
+ (2 << BR_PS_SHIFT) /* 16 bit port size */ |\
+ BR_V) /* valid */
+#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \
+ | OR_UPM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_4 \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512
+
+/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024)
+/* Flash Write Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024)
+
+/*
+ * SJA1000 CAN controller on Local Bus
+ */
+#define CONFIG_SYS_SJA1000_BASE 0xFBFF0000
+#define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_SJA1000_BASE \
+ | (1 << BR_PS_SHIFT) /* 8 bit port size */ \
+ | BR_V ) /* valid */
+#define CONFIG_SYS_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_GPCM_SCY_5 \
+ | OR_GPCM_EHTR)
+ /* 0xFFFF8052 */
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+
+/*
+ * CPLD on Local Bus
+ */
+#define CONFIG_SYS_CPLD_BASE 0xFBFF8000
+#define CONFIG_SYS_BR2_PRELIM ( CONFIG_SYS_CPLD_BASE \
+ | (1 << BR_PS_SHIFT) /* 8 bit port size */ \
+ | BR_V ) /* valid */
+#define CONFIG_SYS_OR2_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_GPCM_SCY_4 \
+ | OR_GPCM_EHTR)
+ /* 0xFFFF8042 */
+
+#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM 0x8000000E /* 32KB */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCIE1_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
+#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
+#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
+#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
+
+/*
+ * Fake PCIE2 definitions: there is no PCIE2 on this board but the code
+ * in arch/powerpc/cpu/mpc83xx/pcie.c doesn't compile without this
+ */
+#define CONFIG_SYS_PCIE2_BASE 0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
+#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000
+#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000
+#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
+
+#define CONFIG_PCI
+#define CONFIG_PCIE
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
+
+/*
+ * TSEC
+ */
+#define CONFIG_NET_MULTI
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
+
+/*
+ * TSEC ethernet configuration
+ */
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_TSEC1_NAME "eTSEC0"
+#define CONFIG_TSEC2_NAME "eTSEC1"
+#define TSEC1_PHY_ADDR 1
+#define TSEC2_PHY_ADDR 2
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS 0
+#define TSEC2_FLAGS 0
+
+/* Options are: eTSEC[0-1] */
+#define CONFIG_ETHPRIME "eTSEC0"
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
+ CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+ HID0_ENABLE_INSTRUCTION_CACHE | \
+ HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
+#define CONFIG_SYS_HID2 HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+
+/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
+ BATU_VP)
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | \
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
+
+#define xstr(s) str(s)
+#define str(s) #s
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs}" \
+ " console=${consoledev},${baudrate}\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addmisc=setenv bootargs ${bootargs}\0" \
+ "kernel_addr=FC0A0000\0" \
+ "fdt_addr=FC2A0000\0" \
+ "ramdisk_addr=FC2C0000\0" \
+ "u-boot=mpc8308_p1m/u-boot.bin\0" \
+ "kernel_addr_r=1000000\0" \
+ "fdt_addr_r=C00000\0" \
+ "hostname=mpc8308_p1m\0" \
+ "bootfile=mpc8308_p1m/uImage\0" \
+ "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \
+ "rootpath=/opt/eldk-4.2/ppc_6xx\0" \
+ "flash_self=run ramargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
+ "tftp ${fdt_addr_r} ${fdtfile};" \
+ "run nfsargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
+ "bootcmd=run flash_self\0" \
+ "load=tftp ${loadaddr} ${u-boot}\0" \
+ "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};cp.b ${fileaddr} " \
+ xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
+ "upd=run load update\0" \
+
+#endif /* __CONFIG_H */
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH][v3] mpc8308_p1m: support for MPC8308 P1M board
2010-09-08 21:36 ` [U-Boot] [PATCH][v3] " Ilya Yanok
@ 2010-09-14 1:12 ` Kim Phillips
2010-09-14 20:40 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Ilya Yanok
2010-09-18 20:35 ` [U-Boot] [PATCH][v3] " Wolfgang Denk
0 siblings, 2 replies; 23+ messages in thread
From: Kim Phillips @ 2010-09-14 1:12 UTC (permalink / raw)
To: u-boot
On Wed, 8 Sep 2010 23:36:59 +0200
Ilya Yanok <yanok@emcraft.com> wrote:
>
> MAINTAINERS | 1 +
> board/mpc8308_p1m/Makefile | 52 ++++
> board/mpc8308_p1m/config.mk | 1 +
> board/mpc8308_p1m/mpc8308_p1m.c | 122 +++++++++
> board/mpc8308_p1m/sdram.c | 93 +++++++
> boards.cfg | 1 +
> include/configs/mpc8308_p1m.h | 548 +++++++++++++++++++++++++++++++++++++++
missing MAKEALL entry.
> +++ b/board/mpc8308_p1m/config.mk
> @@ -0,0 +1 @@
> +TEXT_BASE = 0xFC000000
ifndef TEXT_BASE
TEXT_BASE = 0xFC000000
endif
> +int board_early_init_f(void)
> +{
> + immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
> +
> + if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
> + gd->flags |= GD_FLG_SILENT;
this needs to be deleted - the 8308 doesn't have a pmccr1. Same
problem with the 8308rdb.
> + /* initialized GPIO default directions and values */
> + __raw_writel(CONFIG_GPIO_PDAT, &im->gpio[0].dat);
> + __raw_writel(CONFIG_GPIO_PDIR, &im->gpio[0].dir);
> +
is there a reason CONFIG_SYS_GPIO1_[DIR|DAT] isn't being used instead
of declaring new CONFIG_GPIO_P* macros?
> +void pci_init_board(void)
> + clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM ,
> + SCCR_PCIEXP1CM_1);
add support for setting sccr PCIEXPCM bits in mpc83xx/cpu_init.c, and
define CONFIG_SYS_SCCR_ values in the board config.
> +int board_eth_init(bd_t *bis)
> +{
> + int rv, num_if = 0;
> +
> + /* Initialize TSECs first */
> + if ((rv = cpu_eth_init(bis)) >= 0)
no assignments in if statements.
> + * System IO Config
> + */
> +#define CONFIG_SYS_SICRH 0xf577d100
> +#define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */
Use the SICR[H|L]_ macros to demystify these values (same for 8308erdb).
> +/* GPIO Default input/output settings */
> +#define CONFIG_GPIO_PDIR 0x7AAF8C00
this should be defining CONFIG_SYS_GPIO1_DIR instead.
> +/*
> + * Default GPIO values:
> + * LED#1 enabled; WLAN enabled; Both COM LED on (orange)
> + */
> +#define CONFIG_GPIO_PDAT 0x08008C00
this should be defining CONFIG_SYS_GPIO1_DAT instead.
> +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE
> +#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
lose the comment and replace with (LBLAWAR_EN | LBLAWAR_32KB).
> +/*
> + * CPLD on Local Bus
> + */
> +#define CONFIG_SYS_CPLD_BASE 0xFBFF8000
> +#define CONFIG_SYS_BR2_PRELIM ( CONFIG_SYS_CPLD_BASE \
> + | (1 << BR_PS_SHIFT) /* 8 bit port size */ \
> + | BR_V ) /* valid */
> +#define CONFIG_SYS_OR2_PRELIM ( 0xFFFF8000 /* length 32K */ \
> + | OR_GPCM_SCY_4 \
> + | OR_GPCM_EHTR)
> + /* 0xFFFF8042 */
> +
> +#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE
> +#define CONFIG_SYS_LBLAWAR2_PRELIM 0x8000000E /* 32KB */
same here.
> +/*
> + * Fake PCIE2 definitions: there is no PCIE2 on this board but the code
> + * in arch/powerpc/cpu/mpc83xx/pcie.c doesn't compile without this
> + */
so fix the code there instead.
Kim
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured
2010-09-14 1:12 ` Kim Phillips
@ 2010-09-14 20:40 ` Ilya Yanok
2010-09-14 20:40 ` [U-Boot] [PATCH 2/5] mpc83xx: add support for setting PCIE clocks Ilya Yanok
2010-09-16 23:54 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Kim Phillips
2010-09-18 20:35 ` [U-Boot] [PATCH][v3] " Wolfgang Denk
1 sibling, 2 replies; 23+ messages in thread
From: Ilya Yanok @ 2010-09-14 20:40 UTC (permalink / raw)
To: u-boot
MPC8308 has only one PCIE host controller so we want it to compile
without CONFIG_SYS_PCIE2_CFG_{BASE,SIZE} defined.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
arch/powerpc/cpu/mpc83xx/pcie.c | 47 ++++++++++++++++++++++++++++----------
1 files changed, 34 insertions(+), 13 deletions(-)
diff --git a/arch/powerpc/cpu/mpc83xx/pcie.c b/arch/powerpc/cpu/mpc83xx/pcie.c
index 77f8906..abb7a49 100644
--- a/arch/powerpc/cpu/mpc83xx/pcie.c
+++ b/arch/powerpc/cpu/mpc83xx/pcie.c
@@ -28,7 +28,11 @@
DECLARE_GLOBAL_DATA_PTR;
+#if defined(CONFIG_SYS_PCIE2_CFG_BASE) && defined(CONFIG_SYS_PCIE2_SIZE)
#define PCIE_MAX_BUSES 2
+#else
+#define PCIE_MAX_BUSES 1
+#endif
#ifdef CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES
@@ -93,6 +97,18 @@ static void mpc83xx_pcie_register_hose(int bus, struct pci_region *reg,
static struct pci_controller pcie_hose[PCIE_MAX_BUSES];
struct pci_controller *hose = &pcie_hose[bus];
int i;
+ unsigned int *cfg_addr;
+
+ if (bus == 0) {
+ cfg_addr = (unsigned int *)CONFIG_SYS_PCIE1_CFG_BASE;
+ } else {
+#if defined(CONFIG_SYS_PCIE2_CFG_BASE) && defined(CONFIG_SYS_PCIE2_SIZE)
+ cfg_addr = (unsigned int *)CONFIG_SYS_PCIE2_CFG_BASE;
+#else
+ printf("Second PCIE host controller not configured!\n");
+ return;
+#endif
+ }
/*
* There are no spare BATs to remap all PCI-E windows for U-Boot, so
@@ -124,10 +140,7 @@ static void mpc83xx_pcie_register_hose(int bus, struct pci_region *reg,
hose->first_busno = pci_last_busno() + 1;
hose->last_busno = 0xff;
- if (bus == 0)
- hose->cfg_addr = (unsigned int *)CONFIG_SYS_PCIE1_CFG_BASE;
- else
- hose->cfg_addr = (unsigned int *)CONFIG_SYS_PCIE2_CFG_BASE;
+ hose->cfg_addr = cfg_addr;
pci_set_ops(hose,
pcie_read_config_byte,
@@ -170,6 +183,21 @@ static void mpc83xx_pcie_init_bus(int bus, struct pci_region *reg)
unsigned int tar;
u16 reg16;
int i;
+ u32 cfg_size;
+ u32 cfg_base;
+
+ if (bus) {
+#if defined(CONFIG_SYS_PCIE2_CFG_BASE) && defined(CONFIG_SYS_PCIE2_SIZE)
+ cfg_size = CONFIG_SYS_PCIE2_SIZE;
+ cfg_base = CONFIG_SYS_PCIE2_CFG_BASE;
+#else
+ printf("Second PCIE host controller not configured!\n");
+ return;
+#endif
+ } else {
+ cfg_size = CONFIG_SYS_PCIE1_CFG_SIZE;
+ cfg_base = CONFIG_SYS_PCIE1_CFG_BASE;
+ }
/* Enable pex csb bridge inbound & outbound transactions */
out_le32(&pex->bridge.pex_csb_ctrl,
@@ -182,15 +210,8 @@ static void mpc83xx_pcie_init_bus(int bus, struct pci_region *reg)
PEX_CSB_OBCTRL_CFGWE);
out_win = &pex->bridge.pex_outbound_win[0];
- if (bus) {
- out_le32(&out_win->ar, PEX_OWAR_EN | PEX_OWAR_TYPE_CFG |
- CONFIG_SYS_PCIE2_CFG_SIZE);
- out_le32(&out_win->bar, CONFIG_SYS_PCIE2_CFG_BASE);
- } else {
- out_le32(&out_win->ar, PEX_OWAR_EN | PEX_OWAR_TYPE_CFG |
- CONFIG_SYS_PCIE1_CFG_SIZE);
- out_le32(&out_win->bar, CONFIG_SYS_PCIE1_CFG_BASE);
- }
+ out_le32(&out_win->ar, PEX_OWAR_EN | PEX_OWAR_TYPE_CFG | cfg_size);
+ out_le32(&out_win->bar, cfg_base);
out_le32(&out_win->tarl, 0);
out_le32(&out_win->tarh, 0);
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 2/5] mpc83xx: add support for setting PCIE clocks
2010-09-14 20:40 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Ilya Yanok
@ 2010-09-14 20:40 ` Ilya Yanok
2010-09-14 20:40 ` [U-Boot] [PATCH 3/5] mpc8308: add SICR{L,H} fields definitions Ilya Yanok
2010-09-16 23:54 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Kim Phillips
1 sibling, 1 reply; 23+ messages in thread
From: Ilya Yanok @ 2010-09-14 20:40 UTC (permalink / raw)
To: u-boot
This patch adds support for setting PCIE clocks in cpu_init.c by
providing CONFIG_SYS_SCCR_PCIEXP{1,2} in configuration.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
arch/powerpc/cpu/mpc83xx/cpu_init.c | 12 ++++++++++++
1 files changed, 12 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/cpu/mpc83xx/cpu_init.c b/arch/powerpc/cpu/mpc83xx/cpu_init.c
index 83cba93..f01c09a 100644
--- a/arch/powerpc/cpu/mpc83xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc83xx/cpu_init.c
@@ -126,6 +126,12 @@ void cpu_init_f (volatile immap_t * im)
#ifdef CONFIG_SYS_SCCR_PCICM /* PCI & DMA clock mode */
SCCR_PCICM |
#endif
+#ifdef CONFIG_SYS_SCCR_PCIEXP1CM /* PCIE1 clock mode */
+ SCCR_PCIEXP1CM |
+#endif
+#ifdef CONFIG_SYS_SCCR_PCIEXP2CM /* PCIE2 clock mode */
+ SCCR_PCIEXP2CM |
+#endif
#ifdef CONFIG_SYS_SCCR_TSECCM /* all TSEC's clock mode */
SCCR_TSECCM |
#endif
@@ -158,6 +164,12 @@ void cpu_init_f (volatile immap_t * im)
#ifdef CONFIG_SYS_SCCR_PCICM /* PCI & DMA clock mode */
(CONFIG_SYS_SCCR_PCICM << SCCR_PCICM_SHIFT) |
#endif
+#ifdef CONFIG_SYS_SCCR_PCIEXP1CM /* PCIE1 clock mode */
+ (CONFIG_SYS_SCCR_PCIEXP1CM << SCCR_PCIEXP1CM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_PCIEXP2CM /* PCIE2 clock mode */
+ (CONFIG_SYS_SCCR_PCIEXP2CM << SCCR_PCIEXP2CM_SHIFT) |
+#endif
#ifdef CONFIG_SYS_SCCR_TSECCM /* all TSEC's clock mode */
(CONFIG_SYS_SCCR_TSECCM << SCCR_TSECCM_SHIFT) |
#endif
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 3/5] mpc8308: add SICR{L,H} fields definitions
2010-09-14 20:40 ` [U-Boot] [PATCH 2/5] mpc83xx: add support for setting PCIE clocks Ilya Yanok
@ 2010-09-14 20:40 ` Ilya Yanok
2010-09-14 20:40 ` [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups Ilya Yanok
0 siblings, 1 reply; 23+ messages in thread
From: Ilya Yanok @ 2010-09-14 20:40 UTC (permalink / raw)
To: u-boot
This patch adds defines to set supported fields in System I/O
Configuration Registers High and Low on Freescale MPC8308 CPU.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
include/mpc83xx.h | 48 ++++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 48 insertions(+), 0 deletions(-)
diff --git a/include/mpc83xx.h b/include/mpc83xx.h
index ba6cdf1..0ae83da 100644
--- a/include/mpc83xx.h
+++ b/include/mpc83xx.h
@@ -319,6 +319,54 @@
#define SICRH_GPIO2_H 0x00000030
#define SICRH_SPI 0x00000003
#define SICRH_SPI_SD 0x00000001
+
+#elif defined(CONFIG_MPC8308)
+/* SICRL bits - MPC8308 specific */
+#define SICRL_SPI_PF0 (0 << 28)
+#define SICRL_SPI_PF1 (1 << 28)
+#define SICRL_SPI_PF3 (3 << 28)
+#define SICRL_UART_PF0 (0 << 26)
+#define SICRL_UART_PF1 (1 << 26)
+#define SICRL_UART_PF3 (3 << 26)
+#define SICRL_IRQ_PF0 (0 << 24)
+#define SICRL_IRQ_PF1 (1 << 24)
+#define SICRL_I2C2_PF0 (0 << 20)
+#define SICRL_I2C2_PF1 (1 << 20)
+#define SICRL_ETSEC1_TX_CLK (0 << 6)
+#define SICRL_ETSEC1_GTX_CLK125 (1 << 6)
+
+/* SICRH bits - MPC8308 specific */
+#define SICRH_ESDHC_A_SD (0 << 30)
+#define SICRH_ESDHC_A_GTM (1 << 30)
+#define SICRH_ESDHC_A_GPIO (3 << 30)
+#define SICRH_ESDHC_B_SD (0 << 28)
+#define SICRH_ESDHC_B_GTM (1 << 28)
+#define SICRH_ESDHC_B_GPIO (3 << 28)
+#define SICRH_ESDHC_C_SD (0 << 26)
+#define SICRH_ESDHC_C_GTM (1 << 26)
+#define SICRH_ESDHC_C_GPIO (3 << 26)
+#define SICRH_GPIO_A_GPIO (0 << 24)
+#define SICRH_GPIO_A_TSEC2 (1 << 24)
+#define SICRH_GPIO_B_GPIO (0 << 22)
+#define SICRH_GPIO_B_TSEC2_TX_CLK (1 << 22)
+#define SICRH_GPIO_B_TSEC2_GTX_CLK125 (2 << 22)
+#define SICRH_IEEE1588_A_TMR (1 << 20)
+#define SICRH_IEEE1588_A_GPIO (3 << 20)
+#define SICRH_USB (1 << 18)
+#define SICRH_GTM_GTM (1 << 16)
+#define SICRH_GTM_GPIO (3 << 16)
+#define SICRH_IEEE1588_B_TMR (1 << 14)
+#define SICRH_IEEE1588_B_GPIO (3 << 14)
+#define SICRH_ETSEC2_CRS (1 << 12)
+#define SICRH_ETSEC2_GPIO (3 << 12)
+#define SICRH_GPIOSEL_0 (0 << 8)
+#define SICRH_GPIOSEL_1 (1 << 8)
+#define SICRH_TMROBI_V3P3 (0 << 4)
+#define SICRH_TMROBI_V2P5 (1 << 4)
+#define SICRH_TSOBI1_V3P3 (0 << 1)
+#define SICRH_TSOBI1_V2P5 (1 << 1)
+#define SICRH_TSOBI2_V3P3 (0 << 0)
+#define SICRH_TSOBI2_V2P5 (1 << 0)
#endif
/* SWCRR - System Watchdog Control Register
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups
2010-09-14 20:40 ` [U-Boot] [PATCH 3/5] mpc8308: add SICR{L,H} fields definitions Ilya Yanok
@ 2010-09-14 20:40 ` Ilya Yanok
2010-09-14 20:40 ` [U-Boot] [PATCH 5/5] mpc8308_p1m: support for MPC8308 P1M board Ilya Yanok
2010-09-16 23:56 ` [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups Kim Phillips
0 siblings, 2 replies; 23+ messages in thread
From: Ilya Yanok @ 2010-09-14 20:40 UTC (permalink / raw)
To: u-boot
This patch cleans up the Freescale MPC8308RDB Development board support.
Things fixed:
- Removed unused PCIE2 definitions from configuration
- SICR{L,H} defines used for System I/O Configuration Registers values
instead of hardcoding
- CONFIG_SYS_SCCR_PCIEXP1CM used to enable PCIE clock instead of
writing to SCCR from the board code
- sleep mode stuff removed as MPC8308 has no support for deep sleep and
PMCCR1 register. board_early_init_f() removed.
- MPC8308 has no ERRATA for DDR controller so workaround removed
- 'assignment in if statement' issues solved
- use LBLAWAR_* defines instead of hardcoding
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
board/freescale/mpc8308rdb/mpc8308rdb.c | 19 +++----------
board/freescale/mpc8308rdb/sdram.c | 31 +--------------------
include/configs/MPC8308RDB.h | 46 +++++++++++++++++-------------
3 files changed, 31 insertions(+), 65 deletions(-)
diff --git a/board/freescale/mpc8308rdb/mpc8308rdb.c b/board/freescale/mpc8308rdb/mpc8308rdb.c
index a864189..4acc9a8 100644
--- a/board/freescale/mpc8308rdb/mpc8308rdb.c
+++ b/board/freescale/mpc8308rdb/mpc8308rdb.c
@@ -36,16 +36,6 @@
DECLARE_GLOBAL_DATA_PTR;
-int board_early_init_f(void)
-{
- immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
-
- if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
- gd->flags |= GD_FLG_SILENT;
-
- return 0;
-}
-
static u8 read_board_info(void)
{
u8 val8;
@@ -103,9 +93,6 @@ void pci_init_board(void)
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
- clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM ,
- SCCR_PCIEXP1CM_1);
-
/* Deassert the resets in the control register */
out_be32(&sysconf->pecr1, 0xE0008000);
udelay(2000);
@@ -146,12 +133,14 @@ int board_eth_init(bd_t *bis)
int rv, num_if = 0;
/* Initialize TSECs first */
- if ((rv = cpu_eth_init(bis)) >= 0)
+ rv = cpu_eth_init(bis);
+ if (rv >= 0)
num_if += rv;
else
printf("ERROR: failed to initialize TSECs.\n");
- if ((rv = pci_eth_init(bis)) >= 0)
+ rv = pci_eth_init(bis);
+ if (rv >= 0)
num_if += rv;
else
printf("ERROR: failed to initialize PCI Ethernet.\n");
diff --git a/board/freescale/mpc8308rdb/sdram.c b/board/freescale/mpc8308rdb/sdram.c
index 939c1b8..1a6b9c7 100644
--- a/board/freescale/mpc8308rdb/sdram.c
+++ b/board/freescale/mpc8308rdb/sdram.c
@@ -38,20 +38,6 @@
DECLARE_GLOBAL_DATA_PTR;
-static void resume_from_sleep(void)
-{
- u32 magic = *(u32 *)0;
-
- typedef void (*func_t)(void);
- func_t resume = *(func_t *)4;
-
- if (magic == 0xf5153ae5)
- resume();
-
- gd->flags &= ~GD_FLG_SILENT;
- puts("\nResume from sleep failed: bad magic word\n");
-}
-
/* Fixed sdram init -- doesn't use serial presence detect.
*
* This is useful for faster booting in configs where the RAM is unlikely
@@ -68,12 +54,6 @@ static long fixed_sdram(void)
out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
- /*
- * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
- * or the DDR2 controller may fail to initialize correctly.
- */
- udelay(50000);
-
out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
@@ -86,13 +66,7 @@ static long fixed_sdram(void)
out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
- if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF) {
- out_be32(&im->ddr.sdram_cfg,
- CONFIG_SYS_DDR_SDRAM_CFG | SDRAM_CFG_BI);
- } else {
- out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
- }
-
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
@@ -118,9 +92,6 @@ phys_size_t initdram(int board_type)
/* DDR SDRAM */
msize = fixed_sdram();
- if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
- resume_from_sleep();
-
/* return total bus SDRAM size(bytes) -- DDR */
return msize;
}
diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h
index 6cd5da7..1730be4 100644
--- a/include/configs/MPC8308RDB.h
+++ b/include/configs/MPC8308RDB.h
@@ -85,10 +85,27 @@
/*
* System IO Config
*/
-#define CONFIG_SYS_SICRH 0x01b7d103
-#define CONFIG_SYS_SICRL 0x00000040 /* 3.3V, no delay */
-
-#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+#define CONFIG_SYS_SICRH (\
+ SICRH_ESDHC_A_SD |\
+ SICRH_ESDHC_B_SD |\
+ SICRH_ESDHC_C_SD |\
+ SICRH_GPIO_A_TSEC2 |\
+ SICRH_GPIO_B_TSEC2_GTX_CLK125 |\
+ SICRH_IEEE1588_A_GPIO |\
+ SICRH_USB |\
+ SICRH_GTM_GPIO |\
+ SICRH_IEEE1588_B_GPIO |\
+ SICRH_ETSEC2_CRS |\
+ SICRH_GPIOSEL_1 |\
+ SICRH_TMROBI_V3P3 |\
+ SICRH_TSOBI1_V2P5 |\
+ SICRH_TSOBI2_V2P5) /* 0x01b7d103 */
+#define CONFIG_SYS_SICRL (\
+ SICRL_SPI_PF0 |\
+ SICRL_UART_PF0 |\
+ SICRL_IRQ_PF0 |\
+ SICRL_I2C2_PF0 |\
+ SICRL_ETSEC1_GTX_CLK125) /* 0x00000040 */
/*
* IMMR new address
@@ -218,7 +235,7 @@
/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
#define CONFIG_SYS_BR0_PRELIM (\
CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\
@@ -260,7 +277,7 @@
/* 0xFFFF8396 */
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
#ifdef CONFIG_VSC7385_ENET
#define CONFIG_TSEC2
@@ -270,7 +287,7 @@
/* Access window base at VSC7385 base */
#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE
/* Access window size 128K */
-#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010
+#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_128KB)
/* The flash address and size of the VSC7385 firmware image */
#define CONFIG_VSC7385_IMAGE 0xFE7FE000
#define CONFIG_VSC7385_IMAGE_SIZE 8192
@@ -336,19 +353,8 @@
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
-/*
- * Fake PCIE2 definitions: there is no PCIE2 on this board but the code
- * in arch/powerpc/cpu/mpc83xx/pcie.c doesn't compile without this
- */
-#define CONFIG_SYS_PCIE2_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
-#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000
-#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000
-#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
+/* enable PCIE clock */
+#define CONFIG_SYS_SCCR_PCIEXP1CM 1
#define CONFIG_PCI
#define CONFIG_PCIE
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 5/5] mpc8308_p1m: support for MPC8308 P1M board
2010-09-14 20:40 ` [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups Ilya Yanok
@ 2010-09-14 20:40 ` Ilya Yanok
2010-09-16 23:56 ` [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups Kim Phillips
1 sibling, 0 replies; 23+ messages in thread
From: Ilya Yanok @ 2010-09-14 20:40 UTC (permalink / raw)
To: u-boot
This patch provides support for MPC8308 P1M board with the following
set of features:
Dual UART is supported
NOR flash is supported
Both TSEC Ethernet controllers are supported
PCI Express initialization is supported
Both I2C controllers are supported
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
Kim's comments addressed (except for MAKEALL one I believe boards
from boards.cfg are now in MAKEALL automagically).
Regards, Ilya.
MAINTAINERS | 1 +
board/mpc8308_p1m/Makefile | 52 ++++
board/mpc8308_p1m/config.mk | 3 +
board/mpc8308_p1m/mpc8308_p1m.c | 107 ++++++++
board/mpc8308_p1m/sdram.c | 93 +++++++
boards.cfg | 1 +
include/configs/mpc8308_p1m.h | 555 +++++++++++++++++++++++++++++++++++++++
7 files changed, 812 insertions(+), 0 deletions(-)
create mode 100644 board/mpc8308_p1m/Makefile
create mode 100644 board/mpc8308_p1m/config.mk
create mode 100644 board/mpc8308_p1m/mpc8308_p1m.c
create mode 100644 board/mpc8308_p1m/sdram.c
create mode 100644 include/configs/mpc8308_p1m.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 0c6ce2b..2cf29dd 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -486,6 +486,7 @@ Stephen Williams <steve@icarus.com>
Ilya Yanok <yanok@emcraft.com>
+ mpc8308_p1m MPC8308
MPC8308RDB MPC8308
Roy Zang <tie-fei.zang@freescale.com>
diff --git a/board/mpc8308_p1m/Makefile b/board/mpc8308_p1m/Makefile
new file mode 100644
index 0000000..e9bfa2b
--- /dev/null
+++ b/board/mpc8308_p1m/Makefile
@@ -0,0 +1,52 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+# (C) Copyright 2010
+# Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o sdram.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/mpc8308_p1m/config.mk b/board/mpc8308_p1m/config.mk
new file mode 100644
index 0000000..183d3e8
--- /dev/null
+++ b/board/mpc8308_p1m/config.mk
@@ -0,0 +1,3 @@
+ifndef TEXT_BASE
+TEXT_BASE = 0xFC000000
+endif
diff --git a/board/mpc8308_p1m/mpc8308_p1m.c b/board/mpc8308_p1m/mpc8308_p1m.c
new file mode 100644
index 0000000..9a8b53b
--- /dev/null
+++ b/board/mpc8308_p1m/mpc8308_p1m.c
@@ -0,0 +1,107 @@
+/*
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_mpc83xx_serdes.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ printf("Board: MPC8308 P1M\n");
+
+ return 0;
+}
+
+static struct pci_region pcie_regions_0[] = {
+ {
+ .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+ .size = CONFIG_SYS_PCIE1_MEM_SIZE,
+ .flags = PCI_REGION_MEM,
+ },
+ {
+ .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+ .size = CONFIG_SYS_PCIE1_IO_SIZE,
+ .flags = PCI_REGION_IO,
+ },
+};
+
+void pci_init_board(void)
+{
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+ sysconf83xx_t *sysconf = &immr->sysconf;
+ clk83xx_t *clk = (clk83xx_t *)&immr->clk;
+ law83xx_t *pcie_law = sysconf->pcielaw;
+ struct pci_region *pcie_reg[] = { pcie_regions_0 };
+
+ fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
+ FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+ /* Deassert the resets in the control register */
+ out_be32(&sysconf->pecr1, 0xE0008000);
+ udelay(2000);
+
+ /* Configure PCI Express Local Access Windows */
+ out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+ out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+ mpc83xx_pcie_init(1, pcie_reg, 0);
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+ fdt_fixup_dr_usb(blob, bd);
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rv, num_if = 0;
+
+ /* Initialize TSECs first */
+ rv = cpu_eth_init(bis);
+ if (rv >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize TSECs.\n");
+
+ rv = pci_eth_init(bis);
+ if (rv >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize PCI Ethernet.\n");
+
+ return num_if;
+}
diff --git a/board/mpc8308_p1m/sdram.c b/board/mpc8308_p1m/sdram.c
new file mode 100644
index 0000000..a6e44e6
--- /dev/null
+++ b/board/mpc8308_p1m/sdram.c
@@ -0,0 +1,93 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ * This files is mostly identical to the original from
+ * board/freescale/mpc8308rdb/sdram.c
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+ u32 msize_log2 = __ilog2(msize);
+
+ out_be32(&im->sysconf.ddrlaw[0].bar,
+ CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000);
+ out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
+ out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+ out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+ out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
+
+ /* Currently we use only one CS, so disable the other bank. */
+ out_be32(&im->ddr.cs_config[1], 0);
+
+ out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL);
+ out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
+ out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
+ out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+ out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
+
+ out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ sync();
+
+ /* enable DDR controller */
+ setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+ sync();
+
+ return get_ram_size(CONFIG_SYS_DDR_SDRAM_BASE, msize);
+}
+
+phys_size_t initdram(int board_type)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize;
+
+ if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ /* DDR SDRAM */
+ msize = fixed_sdram();
+
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize;
+}
diff --git a/boards.cfg b/boards.cfg
index 05ddb8c..b9d4a77 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -334,6 +334,7 @@ ppmc8260 powerpc mpc8260
RPXsuper powerpc mpc8260 rpxsuper
rsdproto powerpc mpc8260
MPC8266ADS powerpc mpc8260 mpc8266ads freescale
+mpc8308_p1m powerpc mpc83xx
MPC8308RDB powerpc mpc83xx mpc8308rdb freescale
MPC8323ERDB powerpc mpc83xx mpc8323erdb freescale
MPC8349EMDS powerpc mpc83xx mpc8349emds freescale
diff --git a/include/configs/mpc8308_p1m.h b/include/configs/mpc8308_p1m.h
new file mode 100644
index 0000000..0f8270b
--- /dev/null
+++ b/include/configs/mpc8308_p1m.h
@@ -0,0 +1,555 @@
+/*
+ * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_MPC83xx 1 /* MPC83xx family */
+#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
+#define CONFIG_MPC8308_P1M 1 /* mpc8308_p1m board specific */
+
+/*
+ * On-board devices
+ *
+ * TSECs
+ */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC2
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.66MHz, then
+ * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
+ * We choose the A type silicon as default, so the core is 400Mhz.
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_SVCOD_DIV_2 |\
+ HRCWL_CSB_TO_CLKIN_4X1 |\
+ HRCWL_CORE_TO_CSB_3X1)
+/*
+ * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
+ * in 8308's HRCWH according to the manual, but original Freescale's
+ * code has them and I've expirienced some problems using the board
+ * with BDI3000 attached when I've tried to set these bits to zero
+ * (UART doesn't work after the 'reset run' command).
+ */
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_RL_EXT_LEGACY |\
+ HRCWH_TSEC1M_IN_MII |\
+ HRCWH_TSEC2M_IN_MII |\
+ HRCWH_BIG_ENDIAN)
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRH (\
+ SICRH_ESDHC_A_GPIO |\
+ SICRH_ESDHC_B_GPIO |\
+ SICRH_ESDHC_C_GTM |\
+ SICRH_GPIO_A_TSEC2 |\
+ SICRH_GPIO_B_TSEC2_TX_CLK |\
+ SICRH_IEEE1588_A_GPIO |\
+ SICRH_USB |\
+ SICRH_GTM_GPIO |\
+ SICRH_IEEE1588_B_GPIO |\
+ SICRH_ETSEC2_CRS |\
+ SICRH_GPIOSEL_1 |\
+ SICRH_TMROBI_V3P3 |\
+ SICRH_TSOBI1_V3P3 |\
+ SICRH_TSOBI2_V3P3) /* 0xf577d100 */
+#define CONFIG_SYS_SICRL (\
+ SICRL_SPI_PF0 |\
+ SICRL_UART_PF0 |\
+ SICRL_IRQ_PF0 |\
+ SICRL_I2C2_PF0 |\
+ SICRL_ETSEC1_TX_CLK) /* 0x00000000 */
+
+#define CONFIG_SYS_GPIO1_PRELIM
+/* GPIO Default input/output settings */
+#define CONFIG_SYS_GPIO1_DIR 0x7AAF8C00
+/*
+ * Default GPIO values:
+ * LED#1 enabled; WLAN enabled; Both COM LED on (orange)
+ */
+#define CONFIG_SYS_GPIO1_DAT 0x08008C00
+
+/*
+ * IMMR new address
+ */
+#define CONFIG_SYS_IMMR 0xE0000000
+
+/*
+ * SERDES
+ */
+#define CONFIG_FSL_SERDES
+#define CONFIG_FSL_SERDES1 0xe3000
+
+/*
+ * Arbiter Setup
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
+#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
+ | DDRCDR_PZ_LOZ \
+ | DDRCDR_NZ_LOZ \
+ | DDRCDR_ODT \
+ | DDRCDR_Q_DRN)
+ /* 0x7b880001 */
+/*
+ * Manually set up DDR parameters
+ * consist of two chips HY5PS12621BFP-C4 from HYNIX
+ */
+
+#define CONFIG_SYS_DDR_SIZE 128 /* MB */
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
+ | 0x00010000 /* ODT_WR to CSn */ \
+ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+ /* 0x80010102 */
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
+ | (0 << TIMING_CFG0_WRT_SHIFT) \
+ | (0 << TIMING_CFG0_RRT_SHIFT) \
+ | (0 << TIMING_CFG0_WWT_SHIFT) \
+ | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
+ | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+ /* 0x00220802 */
+#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
+ | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
+ | (5 << TIMING_CFG1_CASLAT_SHIFT) \
+ | (6 << TIMING_CFG1_REFREC_SHIFT) \
+ | (2 << TIMING_CFG1_WRREC_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
+ | (2 << TIMING_CFG1_WRTORD_SHIFT))
+ /* 0x27256222 */
+#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
+ | (4 << TIMING_CFG2_CPO_SHIFT) \
+ | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
+ | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
+ | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
+ | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
+ | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
+ /* 0x121048c5 */
+#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
+ | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+ /* 0x03600100 */
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
+ | SDRAM_CFG_SDRAM_TYPE_DDR2 \
+ | SDRAM_CFG_32_BE)
+ /* 0x43080000 */
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
+#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
+ | (0x0232 << SDRAM_MODE_SD_SHIFT))
+ /* ODT 150ohm CL=3, AL=1 on SDRAM */
+#define CONFIG_SYS_DDR_MODE2 0x00000000
+
+/*
+ * Memory test
+ */
+#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x07f00000
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR 0x00040000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+
+#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
+
+/* Window base@flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB)
+
+#define CONFIG_SYS_BR0_PRELIM (\
+ CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\
+ (2 << BR_PS_SHIFT) /* 16 bit port size */ |\
+ BR_V) /* valid */
+#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \
+ | OR_UPM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_4 \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512
+
+/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024)
+/* Flash Write Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024)
+
+/*
+ * SJA1000 CAN controller on Local Bus
+ */
+#define CONFIG_SYS_SJA1000_BASE 0xFBFF0000
+#define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_SJA1000_BASE \
+ | (1 << BR_PS_SHIFT) /* 8 bit port size */ \
+ | BR_V ) /* valid */
+#define CONFIG_SYS_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_GPCM_SCY_5 \
+ | OR_GPCM_EHTR)
+ /* 0xFFFF8052 */
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
+
+/*
+ * CPLD on Local Bus
+ */
+#define CONFIG_SYS_CPLD_BASE 0xFBFF8000
+#define CONFIG_SYS_BR2_PRELIM ( CONFIG_SYS_CPLD_BASE \
+ | (1 << BR_PS_SHIFT) /* 8 bit port size */ \
+ | BR_V ) /* valid */
+#define CONFIG_SYS_OR2_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_GPCM_SCY_4 \
+ | OR_GPCM_EHTR)
+ /* 0xFFFF8042 */
+
+#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCIE1_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
+#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
+#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
+#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
+
+/* enable PCIE clock */
+#define CONFIG_SYS_SCCR_PCIEXP1CM 1
+
+#define CONFIG_PCI
+#define CONFIG_PCIE
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
+
+/*
+ * TSEC
+ */
+#define CONFIG_NET_MULTI
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
+
+/*
+ * TSEC ethernet configuration
+ */
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_TSEC1_NAME "eTSEC0"
+#define CONFIG_TSEC2_NAME "eTSEC1"
+#define TSEC1_PHY_ADDR 1
+#define TSEC2_PHY_ADDR 2
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS 0
+#define TSEC2_FLAGS 0
+
+/* Options are: eTSEC[0-1] */
+#define CONFIG_ETHPRIME "eTSEC0"
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
+ CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+ HID0_ENABLE_INSTRUCTION_CACHE | \
+ HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
+#define CONFIG_SYS_HID2 HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+
+/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
+ BATU_VP)
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | \
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
+
+#define xstr(s) str(s)
+#define str(s) #s
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs}" \
+ " console=${consoledev},${baudrate}\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addmisc=setenv bootargs ${bootargs}\0" \
+ "kernel_addr=FC0A0000\0" \
+ "fdt_addr=FC2A0000\0" \
+ "ramdisk_addr=FC2C0000\0" \
+ "u-boot=mpc8308_p1m/u-boot.bin\0" \
+ "kernel_addr_r=1000000\0" \
+ "fdt_addr_r=C00000\0" \
+ "hostname=mpc8308_p1m\0" \
+ "bootfile=mpc8308_p1m/uImage\0" \
+ "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \
+ "rootpath=/opt/eldk-4.2/ppc_6xx\0" \
+ "flash_self=run ramargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
+ "tftp ${fdt_addr_r} ${fdtfile};" \
+ "run nfsargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
+ "bootcmd=run flash_self\0" \
+ "load=tftp ${loadaddr} ${u-boot}\0" \
+ "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};cp.b ${fileaddr} " \
+ xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
+ "upd=run load update\0" \
+
+#endif /* __CONFIG_H */
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured
2010-09-14 20:40 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Ilya Yanok
2010-09-14 20:40 ` [U-Boot] [PATCH 2/5] mpc83xx: add support for setting PCIE clocks Ilya Yanok
@ 2010-09-16 23:54 ` Kim Phillips
2010-09-17 21:35 ` Ilya Yanok
` (5 more replies)
1 sibling, 6 replies; 23+ messages in thread
From: Kim Phillips @ 2010-09-16 23:54 UTC (permalink / raw)
To: u-boot
On Tue, 14 Sep 2010 22:40:37 +0200
Ilya Yanok <yanok@emcraft.com> wrote:
> MPC8308 has only one PCIE host controller so we want it to compile
> without CONFIG_SYS_PCIE2_CFG_{BASE,SIZE} defined.
> +#if defined(CONFIG_SYS_PCIE2_CFG_BASE) && defined(CONFIG_SYS_PCIE2_SIZE)
> #define PCIE_MAX_BUSES 2
> +#else
> +#define PCIE_MAX_BUSES 1
> +#endif
Technically this should be an indirect function of MPC8308, but what's
the problem with leaving MAX_BUSES as 2 always?
> + unsigned int *cfg_addr;
> +
> + if (bus == 0) {
> + cfg_addr = (unsigned int *)CONFIG_SYS_PCIE1_CFG_BASE;
> + } else {
> +#if defined(CONFIG_SYS_PCIE2_CFG_BASE) && defined(CONFIG_SYS_PCIE2_SIZE)
> + cfg_addr = (unsigned int *)CONFIG_SYS_PCIE2_CFG_BASE;
> +#else
> + printf("Second PCIE host controller not configured!\n");
> + return;
> +#endif
let's reduce the new ifdefs introduced in the file down to one, and
still be able remove the 'if (bus)' clauses by adding a static pcie cfg
struct array[], to which this and code below it would directly
dereference with array[bus]. The single ifdef should protect the
second entry in the array. The "second PCIE host controller not
configured" check can be made by comparing num_buses with ARRAY_SIZE
(array) in mpc83xx_pcie_init prior to calling mpc83xx_pcie_init_bus
with an illegal bus value.
Kim
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups
2010-09-14 20:40 ` [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups Ilya Yanok
2010-09-14 20:40 ` [U-Boot] [PATCH 5/5] mpc8308_p1m: support for MPC8308 P1M board Ilya Yanok
@ 2010-09-16 23:56 ` Kim Phillips
1 sibling, 0 replies; 23+ messages in thread
From: Kim Phillips @ 2010-09-16 23:56 UTC (permalink / raw)
To: u-boot
On Tue, 14 Sep 2010 22:40:40 +0200
Ilya Yanok <yanok@emcraft.com> wrote:
> - clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM ,
> - SCCR_PCIEXP1CM_1);
> -
this causes a new warning:
Configuring for MPC8308RDB board...
mpc8308rdb.c: In function 'pci_init_board':
mpc8308rdb.c:89: warning: unused variable 'clk'
same for the 8308_p1m in the next 5/5 patch.
everything else looks good to me.
Thanks,
Kim
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured
2010-09-16 23:54 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Kim Phillips
@ 2010-09-17 21:35 ` Ilya Yanok
2010-09-17 21:41 ` Ilya Yanok
` (4 subsequent siblings)
5 siblings, 0 replies; 23+ messages in thread
From: Ilya Yanok @ 2010-09-17 21:35 UTC (permalink / raw)
To: u-boot
Hi Kim,
On 17.09.2010 03:54, Kim Phillips wrote:
>> +#if defined(CONFIG_SYS_PCIE2_CFG_BASE)&& defined(CONFIG_SYS_PCIE2_SIZE)
>> #define PCIE_MAX_BUSES 2
>> +#else
>> +#define PCIE_MAX_BUSES 1
>> +#endif
>>
> Technically this should be an indirect function of MPC8308, but what's
> the problem with leaving MAX_BUSES as 2 always?
>
Well, we can save a couple of bytes but I agree it doesn't worth it.
I'll remove the ifdef here.
>> + unsigned int *cfg_addr;
>> +
>> + if (bus == 0) {
>> + cfg_addr = (unsigned int *)CONFIG_SYS_PCIE1_CFG_BASE;
>> + } else {
>> +#if defined(CONFIG_SYS_PCIE2_CFG_BASE)&& defined(CONFIG_SYS_PCIE2_SIZE)
>> + cfg_addr = (unsigned int *)CONFIG_SYS_PCIE2_CFG_BASE;
>> +#else
>> + printf("Second PCIE host controller not configured!\n");
>> + return;
>> +#endif
>>
> let's reduce the new ifdefs introduced in the file down to one, and
> still be able remove the 'if (bus)' clauses by adding a static pcie cfg
> struct array[], to which this and code below it would directly
> dereference with array[bus]. The single ifdef should protect the
> second entry in the array. The "second PCIE host controller not
> configured" check can be made by comparing num_buses with ARRAY_SIZE
> (array) in mpc83xx_pcie_init prior to calling mpc83xx_pcie_init_bus
> with an illegal bus value.
>
Yes, this sounds like much cleaner code. I'll post the updated patches
in the short while.
Regards, Ilya.
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured
2010-09-16 23:54 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Kim Phillips
2010-09-17 21:35 ` Ilya Yanok
@ 2010-09-17 21:41 ` Ilya Yanok
2010-09-22 21:02 ` Kim Phillips
2010-09-17 21:41 ` [U-Boot] [PATCH 2/5] mpc83xx: add support for setting PCIE clocks Ilya Yanok
` (3 subsequent siblings)
5 siblings, 1 reply; 23+ messages in thread
From: Ilya Yanok @ 2010-09-17 21:41 UTC (permalink / raw)
To: u-boot
MPC8308 has only one PCIE host controller so we want it to compile
without CONFIG_SYS_PCIE2_CFG_{BASE,SIZE} defined.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
arch/powerpc/cpu/mpc83xx/pcie.c | 38 +++++++++++++++++++++++++-------------
1 files changed, 25 insertions(+), 13 deletions(-)
diff --git a/arch/powerpc/cpu/mpc83xx/pcie.c b/arch/powerpc/cpu/mpc83xx/pcie.c
index 77f8906..e70d19e 100644
--- a/arch/powerpc/cpu/mpc83xx/pcie.c
+++ b/arch/powerpc/cpu/mpc83xx/pcie.c
@@ -30,6 +30,22 @@ DECLARE_GLOBAL_DATA_PTR;
#define PCIE_MAX_BUSES 2
+static struct {
+ u32 base;
+ u32 size;
+} mpc83xx_pcie_cfg_space[] = {
+ {
+ .base = CONFIG_SYS_PCIE1_CFG_BASE,
+ .size = CONFIG_SYS_PCIE1_CFG_SIZE,
+ },
+#if defined(CONFIG_SYS_PCIE2_CFG_BASE) && defined(CONFIG_SYS_PCIE2_CFG_SIZE)
+ {
+ .base = CONFIG_SYS_PCIE2_CFG_BASE,
+ .size = CONFIG_SYS_PCIE2_CFG_SIZE,
+ },
+#endif
+};
+
#ifdef CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES
static int mpc83xx_pcie_remap_cfg(struct pci_controller *hose, pci_dev_t dev)
@@ -124,10 +140,7 @@ static void mpc83xx_pcie_register_hose(int bus, struct pci_region *reg,
hose->first_busno = pci_last_busno() + 1;
hose->last_busno = 0xff;
- if (bus == 0)
- hose->cfg_addr = (unsigned int *)CONFIG_SYS_PCIE1_CFG_BASE;
- else
- hose->cfg_addr = (unsigned int *)CONFIG_SYS_PCIE2_CFG_BASE;
+ hose->cfg_addr = mpc83xx_pcie_cfg_space[bus].base;
pci_set_ops(hose,
pcie_read_config_byte,
@@ -182,15 +195,9 @@ static void mpc83xx_pcie_init_bus(int bus, struct pci_region *reg)
PEX_CSB_OBCTRL_CFGWE);
out_win = &pex->bridge.pex_outbound_win[0];
- if (bus) {
- out_le32(&out_win->ar, PEX_OWAR_EN | PEX_OWAR_TYPE_CFG |
- CONFIG_SYS_PCIE2_CFG_SIZE);
- out_le32(&out_win->bar, CONFIG_SYS_PCIE2_CFG_BASE);
- } else {
- out_le32(&out_win->ar, PEX_OWAR_EN | PEX_OWAR_TYPE_CFG |
- CONFIG_SYS_PCIE1_CFG_SIZE);
- out_le32(&out_win->bar, CONFIG_SYS_PCIE1_CFG_BASE);
- }
+ out_le32(&out_win->ar, PEX_OWAR_EN | PEX_OWAR_TYPE_CFG |
+ mpc83xx_pcie_cfg_space[bus].size);
+ out_le32(&out_win->bar, mpc83xx_pcie_cfg_space[bus].base);
out_le32(&out_win->tarl, 0);
out_le32(&out_win->tarh, 0);
@@ -312,6 +319,11 @@ void mpc83xx_pcie_init(int num_buses, struct pci_region **reg, int warmboot)
*/
udelay(warmboot ? 1000 : 100000);
+ if (num_buses > ARRAY_SIZE(mpc83xx_pcie_cfg_space)) {
+ printf("Second PCIE host contoller not configured!\n");
+ num_buses = ARRAY_SIZE(mpc83xx_pcie_cfg_space);
+ }
+
for (i = 0; i < num_buses; i++)
mpc83xx_pcie_init_bus(i, reg[i]);
}
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 2/5] mpc83xx: add support for setting PCIE clocks
2010-09-16 23:54 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Kim Phillips
2010-09-17 21:35 ` Ilya Yanok
2010-09-17 21:41 ` Ilya Yanok
@ 2010-09-17 21:41 ` Ilya Yanok
2010-09-17 21:41 ` [U-Boot] [PATCH 3/5] mpc8308: add SICR{L,H} fields definitions Ilya Yanok
` (2 subsequent siblings)
5 siblings, 0 replies; 23+ messages in thread
From: Ilya Yanok @ 2010-09-17 21:41 UTC (permalink / raw)
To: u-boot
This patch adds support for setting PCIE clocks in cpu_init.c by
providing CONFIG_SYS_SCCR_PCIEXP{1,2} in configuration.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
arch/powerpc/cpu/mpc83xx/cpu_init.c | 12 ++++++++++++
1 files changed, 12 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/cpu/mpc83xx/cpu_init.c b/arch/powerpc/cpu/mpc83xx/cpu_init.c
index 83cba93..f01c09a 100644
--- a/arch/powerpc/cpu/mpc83xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc83xx/cpu_init.c
@@ -126,6 +126,12 @@ void cpu_init_f (volatile immap_t * im)
#ifdef CONFIG_SYS_SCCR_PCICM /* PCI & DMA clock mode */
SCCR_PCICM |
#endif
+#ifdef CONFIG_SYS_SCCR_PCIEXP1CM /* PCIE1 clock mode */
+ SCCR_PCIEXP1CM |
+#endif
+#ifdef CONFIG_SYS_SCCR_PCIEXP2CM /* PCIE2 clock mode */
+ SCCR_PCIEXP2CM |
+#endif
#ifdef CONFIG_SYS_SCCR_TSECCM /* all TSEC's clock mode */
SCCR_TSECCM |
#endif
@@ -158,6 +164,12 @@ void cpu_init_f (volatile immap_t * im)
#ifdef CONFIG_SYS_SCCR_PCICM /* PCI & DMA clock mode */
(CONFIG_SYS_SCCR_PCICM << SCCR_PCICM_SHIFT) |
#endif
+#ifdef CONFIG_SYS_SCCR_PCIEXP1CM /* PCIE1 clock mode */
+ (CONFIG_SYS_SCCR_PCIEXP1CM << SCCR_PCIEXP1CM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_PCIEXP2CM /* PCIE2 clock mode */
+ (CONFIG_SYS_SCCR_PCIEXP2CM << SCCR_PCIEXP2CM_SHIFT) |
+#endif
#ifdef CONFIG_SYS_SCCR_TSECCM /* all TSEC's clock mode */
(CONFIG_SYS_SCCR_TSECCM << SCCR_TSECCM_SHIFT) |
#endif
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 3/5] mpc8308: add SICR{L,H} fields definitions
2010-09-16 23:54 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Kim Phillips
` (2 preceding siblings ...)
2010-09-17 21:41 ` [U-Boot] [PATCH 2/5] mpc83xx: add support for setting PCIE clocks Ilya Yanok
@ 2010-09-17 21:41 ` Ilya Yanok
2010-09-17 21:41 ` [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups Ilya Yanok
2010-09-17 21:41 ` [U-Boot] [PATCH 5/5] mpc8308_p1m: support for MPC8308 P1M board Ilya Yanok
5 siblings, 0 replies; 23+ messages in thread
From: Ilya Yanok @ 2010-09-17 21:41 UTC (permalink / raw)
To: u-boot
This patch adds defines to set supported fields in System I/O
Configuration Registers High and Low on Freescale MPC8308 CPU.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
include/mpc83xx.h | 48 ++++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 48 insertions(+), 0 deletions(-)
diff --git a/include/mpc83xx.h b/include/mpc83xx.h
index ba6cdf1..0ae83da 100644
--- a/include/mpc83xx.h
+++ b/include/mpc83xx.h
@@ -319,6 +319,54 @@
#define SICRH_GPIO2_H 0x00000030
#define SICRH_SPI 0x00000003
#define SICRH_SPI_SD 0x00000001
+
+#elif defined(CONFIG_MPC8308)
+/* SICRL bits - MPC8308 specific */
+#define SICRL_SPI_PF0 (0 << 28)
+#define SICRL_SPI_PF1 (1 << 28)
+#define SICRL_SPI_PF3 (3 << 28)
+#define SICRL_UART_PF0 (0 << 26)
+#define SICRL_UART_PF1 (1 << 26)
+#define SICRL_UART_PF3 (3 << 26)
+#define SICRL_IRQ_PF0 (0 << 24)
+#define SICRL_IRQ_PF1 (1 << 24)
+#define SICRL_I2C2_PF0 (0 << 20)
+#define SICRL_I2C2_PF1 (1 << 20)
+#define SICRL_ETSEC1_TX_CLK (0 << 6)
+#define SICRL_ETSEC1_GTX_CLK125 (1 << 6)
+
+/* SICRH bits - MPC8308 specific */
+#define SICRH_ESDHC_A_SD (0 << 30)
+#define SICRH_ESDHC_A_GTM (1 << 30)
+#define SICRH_ESDHC_A_GPIO (3 << 30)
+#define SICRH_ESDHC_B_SD (0 << 28)
+#define SICRH_ESDHC_B_GTM (1 << 28)
+#define SICRH_ESDHC_B_GPIO (3 << 28)
+#define SICRH_ESDHC_C_SD (0 << 26)
+#define SICRH_ESDHC_C_GTM (1 << 26)
+#define SICRH_ESDHC_C_GPIO (3 << 26)
+#define SICRH_GPIO_A_GPIO (0 << 24)
+#define SICRH_GPIO_A_TSEC2 (1 << 24)
+#define SICRH_GPIO_B_GPIO (0 << 22)
+#define SICRH_GPIO_B_TSEC2_TX_CLK (1 << 22)
+#define SICRH_GPIO_B_TSEC2_GTX_CLK125 (2 << 22)
+#define SICRH_IEEE1588_A_TMR (1 << 20)
+#define SICRH_IEEE1588_A_GPIO (3 << 20)
+#define SICRH_USB (1 << 18)
+#define SICRH_GTM_GTM (1 << 16)
+#define SICRH_GTM_GPIO (3 << 16)
+#define SICRH_IEEE1588_B_TMR (1 << 14)
+#define SICRH_IEEE1588_B_GPIO (3 << 14)
+#define SICRH_ETSEC2_CRS (1 << 12)
+#define SICRH_ETSEC2_GPIO (3 << 12)
+#define SICRH_GPIOSEL_0 (0 << 8)
+#define SICRH_GPIOSEL_1 (1 << 8)
+#define SICRH_TMROBI_V3P3 (0 << 4)
+#define SICRH_TMROBI_V2P5 (1 << 4)
+#define SICRH_TSOBI1_V3P3 (0 << 1)
+#define SICRH_TSOBI1_V2P5 (1 << 1)
+#define SICRH_TSOBI2_V3P3 (0 << 0)
+#define SICRH_TSOBI2_V2P5 (1 << 0)
#endif
/* SWCRR - System Watchdog Control Register
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups
2010-09-16 23:54 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Kim Phillips
` (3 preceding siblings ...)
2010-09-17 21:41 ` [U-Boot] [PATCH 3/5] mpc8308: add SICR{L,H} fields definitions Ilya Yanok
@ 2010-09-17 21:41 ` Ilya Yanok
2010-09-17 21:41 ` [U-Boot] [PATCH 5/5] mpc8308_p1m: support for MPC8308 P1M board Ilya Yanok
5 siblings, 0 replies; 23+ messages in thread
From: Ilya Yanok @ 2010-09-17 21:41 UTC (permalink / raw)
To: u-boot
This patch cleans up the Freescale MPC8308RDB Development board support.
Things fixed:
- Removed unused PCIE2 definitions from configuration
- SICR{L,H} defines used for System I/O Configuration Registers values
instead of hardcoding
- CONFIG_SYS_SCCR_PCIEXP1CM used to enable PCIE clock instead of
writing to SCCR from the board code
- sleep mode stuff removed as MPC8308 has no support for deep sleep and
PMCCR1 register. board_early_init_f() removed.
- MPC8308 has no ERRATA for DDR controller so workaround removed
- 'assignment in if statement' issues solved
- use LBLAWAR_* defines instead of hardcoding
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
board/freescale/mpc8308rdb/mpc8308rdb.c | 20 +++-----------
board/freescale/mpc8308rdb/sdram.c | 31 +--------------------
include/configs/MPC8308RDB.h | 46 +++++++++++++++++-------------
3 files changed, 31 insertions(+), 66 deletions(-)
diff --git a/board/freescale/mpc8308rdb/mpc8308rdb.c b/board/freescale/mpc8308rdb/mpc8308rdb.c
index a864189..fb29abf 100644
--- a/board/freescale/mpc8308rdb/mpc8308rdb.c
+++ b/board/freescale/mpc8308rdb/mpc8308rdb.c
@@ -36,16 +36,6 @@
DECLARE_GLOBAL_DATA_PTR;
-int board_early_init_f(void)
-{
- immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
-
- if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
- gd->flags |= GD_FLG_SILENT;
-
- return 0;
-}
-
static u8 read_board_info(void)
{
u8 val8;
@@ -96,16 +86,12 @@ void pci_init_board(void)
{
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
sysconf83xx_t *sysconf = &immr->sysconf;
- clk83xx_t *clk = (clk83xx_t *)&immr->clk;
law83xx_t *pcie_law = sysconf->pcielaw;
struct pci_region *pcie_reg[] = { pcie_regions_0 };
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
- clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM ,
- SCCR_PCIEXP1CM_1);
-
/* Deassert the resets in the control register */
out_be32(&sysconf->pecr1, 0xE0008000);
udelay(2000);
@@ -146,12 +132,14 @@ int board_eth_init(bd_t *bis)
int rv, num_if = 0;
/* Initialize TSECs first */
- if ((rv = cpu_eth_init(bis)) >= 0)
+ rv = cpu_eth_init(bis);
+ if (rv >= 0)
num_if += rv;
else
printf("ERROR: failed to initialize TSECs.\n");
- if ((rv = pci_eth_init(bis)) >= 0)
+ rv = pci_eth_init(bis);
+ if (rv >= 0)
num_if += rv;
else
printf("ERROR: failed to initialize PCI Ethernet.\n");
diff --git a/board/freescale/mpc8308rdb/sdram.c b/board/freescale/mpc8308rdb/sdram.c
index 939c1b8..1a6b9c7 100644
--- a/board/freescale/mpc8308rdb/sdram.c
+++ b/board/freescale/mpc8308rdb/sdram.c
@@ -38,20 +38,6 @@
DECLARE_GLOBAL_DATA_PTR;
-static void resume_from_sleep(void)
-{
- u32 magic = *(u32 *)0;
-
- typedef void (*func_t)(void);
- func_t resume = *(func_t *)4;
-
- if (magic == 0xf5153ae5)
- resume();
-
- gd->flags &= ~GD_FLG_SILENT;
- puts("\nResume from sleep failed: bad magic word\n");
-}
-
/* Fixed sdram init -- doesn't use serial presence detect.
*
* This is useful for faster booting in configs where the RAM is unlikely
@@ -68,12 +54,6 @@ static long fixed_sdram(void)
out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
- /*
- * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
- * or the DDR2 controller may fail to initialize correctly.
- */
- udelay(50000);
-
out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
@@ -86,13 +66,7 @@ static long fixed_sdram(void)
out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
- if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF) {
- out_be32(&im->ddr.sdram_cfg,
- CONFIG_SYS_DDR_SDRAM_CFG | SDRAM_CFG_BI);
- } else {
- out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
- }
-
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
@@ -118,9 +92,6 @@ phys_size_t initdram(int board_type)
/* DDR SDRAM */
msize = fixed_sdram();
- if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
- resume_from_sleep();
-
/* return total bus SDRAM size(bytes) -- DDR */
return msize;
}
diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h
index 6cd5da7..1730be4 100644
--- a/include/configs/MPC8308RDB.h
+++ b/include/configs/MPC8308RDB.h
@@ -85,10 +85,27 @@
/*
* System IO Config
*/
-#define CONFIG_SYS_SICRH 0x01b7d103
-#define CONFIG_SYS_SICRL 0x00000040 /* 3.3V, no delay */
-
-#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+#define CONFIG_SYS_SICRH (\
+ SICRH_ESDHC_A_SD |\
+ SICRH_ESDHC_B_SD |\
+ SICRH_ESDHC_C_SD |\
+ SICRH_GPIO_A_TSEC2 |\
+ SICRH_GPIO_B_TSEC2_GTX_CLK125 |\
+ SICRH_IEEE1588_A_GPIO |\
+ SICRH_USB |\
+ SICRH_GTM_GPIO |\
+ SICRH_IEEE1588_B_GPIO |\
+ SICRH_ETSEC2_CRS |\
+ SICRH_GPIOSEL_1 |\
+ SICRH_TMROBI_V3P3 |\
+ SICRH_TSOBI1_V2P5 |\
+ SICRH_TSOBI2_V2P5) /* 0x01b7d103 */
+#define CONFIG_SYS_SICRL (\
+ SICRL_SPI_PF0 |\
+ SICRL_UART_PF0 |\
+ SICRL_IRQ_PF0 |\
+ SICRL_I2C2_PF0 |\
+ SICRL_ETSEC1_GTX_CLK125) /* 0x00000040 */
/*
* IMMR new address
@@ -218,7 +235,7 @@
/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
#define CONFIG_SYS_BR0_PRELIM (\
CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\
@@ -260,7 +277,7 @@
/* 0xFFFF8396 */
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
#ifdef CONFIG_VSC7385_ENET
#define CONFIG_TSEC2
@@ -270,7 +287,7 @@
/* Access window base at VSC7385 base */
#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE
/* Access window size 128K */
-#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010
+#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_128KB)
/* The flash address and size of the VSC7385 firmware image */
#define CONFIG_VSC7385_IMAGE 0xFE7FE000
#define CONFIG_VSC7385_IMAGE_SIZE 8192
@@ -336,19 +353,8 @@
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
-/*
- * Fake PCIE2 definitions: there is no PCIE2 on this board but the code
- * in arch/powerpc/cpu/mpc83xx/pcie.c doesn't compile without this
- */
-#define CONFIG_SYS_PCIE2_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
-#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000
-#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000
-#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
+/* enable PCIE clock */
+#define CONFIG_SYS_SCCR_PCIEXP1CM 1
#define CONFIG_PCI
#define CONFIG_PCIE
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 5/5] mpc8308_p1m: support for MPC8308 P1M board
2010-09-16 23:54 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Kim Phillips
` (4 preceding siblings ...)
2010-09-17 21:41 ` [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups Ilya Yanok
@ 2010-09-17 21:41 ` Ilya Yanok
5 siblings, 0 replies; 23+ messages in thread
From: Ilya Yanok @ 2010-09-17 21:41 UTC (permalink / raw)
To: u-boot
This patch provides support for MPC8308 P1M board with the following
set of features:
Dual UART is supported
NOR flash is supported
Both TSEC Ethernet controllers are supported
PCI Express initialization is supported
Both I2C controllers are supported
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
MAINTAINERS | 1 +
board/mpc8308_p1m/Makefile | 52 ++++
board/mpc8308_p1m/config.mk | 3 +
board/mpc8308_p1m/mpc8308_p1m.c | 106 ++++++++
board/mpc8308_p1m/sdram.c | 93 +++++++
boards.cfg | 1 +
include/configs/mpc8308_p1m.h | 555 +++++++++++++++++++++++++++++++++++++++
7 files changed, 811 insertions(+), 0 deletions(-)
create mode 100644 board/mpc8308_p1m/Makefile
create mode 100644 board/mpc8308_p1m/config.mk
create mode 100644 board/mpc8308_p1m/mpc8308_p1m.c
create mode 100644 board/mpc8308_p1m/sdram.c
create mode 100644 include/configs/mpc8308_p1m.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 0c6ce2b..2cf29dd 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -486,6 +486,7 @@ Stephen Williams <steve@icarus.com>
Ilya Yanok <yanok@emcraft.com>
+ mpc8308_p1m MPC8308
MPC8308RDB MPC8308
Roy Zang <tie-fei.zang@freescale.com>
diff --git a/board/mpc8308_p1m/Makefile b/board/mpc8308_p1m/Makefile
new file mode 100644
index 0000000..e9bfa2b
--- /dev/null
+++ b/board/mpc8308_p1m/Makefile
@@ -0,0 +1,52 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+# (C) Copyright 2010
+# Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o sdram.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/mpc8308_p1m/config.mk b/board/mpc8308_p1m/config.mk
new file mode 100644
index 0000000..183d3e8
--- /dev/null
+++ b/board/mpc8308_p1m/config.mk
@@ -0,0 +1,3 @@
+ifndef TEXT_BASE
+TEXT_BASE = 0xFC000000
+endif
diff --git a/board/mpc8308_p1m/mpc8308_p1m.c b/board/mpc8308_p1m/mpc8308_p1m.c
new file mode 100644
index 0000000..0c70b15
--- /dev/null
+++ b/board/mpc8308_p1m/mpc8308_p1m.c
@@ -0,0 +1,106 @@
+/*
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_mpc83xx_serdes.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ printf("Board: MPC8308 P1M\n");
+
+ return 0;
+}
+
+static struct pci_region pcie_regions_0[] = {
+ {
+ .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+ .size = CONFIG_SYS_PCIE1_MEM_SIZE,
+ .flags = PCI_REGION_MEM,
+ },
+ {
+ .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+ .size = CONFIG_SYS_PCIE1_IO_SIZE,
+ .flags = PCI_REGION_IO,
+ },
+};
+
+void pci_init_board(void)
+{
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+ sysconf83xx_t *sysconf = &immr->sysconf;
+ law83xx_t *pcie_law = sysconf->pcielaw;
+ struct pci_region *pcie_reg[] = { pcie_regions_0 };
+
+ fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
+ FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+ /* Deassert the resets in the control register */
+ out_be32(&sysconf->pecr1, 0xE0008000);
+ udelay(2000);
+
+ /* Configure PCI Express Local Access Windows */
+ out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+ out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+ mpc83xx_pcie_init(1, pcie_reg, 0);
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+ fdt_fixup_dr_usb(blob, bd);
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rv, num_if = 0;
+
+ /* Initialize TSECs first */
+ rv = cpu_eth_init(bis);
+ if (rv >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize TSECs.\n");
+
+ rv = pci_eth_init(bis);
+ if (rv >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize PCI Ethernet.\n");
+
+ return num_if;
+}
diff --git a/board/mpc8308_p1m/sdram.c b/board/mpc8308_p1m/sdram.c
new file mode 100644
index 0000000..a6e44e6
--- /dev/null
+++ b/board/mpc8308_p1m/sdram.c
@@ -0,0 +1,93 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ * This files is mostly identical to the original from
+ * board/freescale/mpc8308rdb/sdram.c
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+ u32 msize_log2 = __ilog2(msize);
+
+ out_be32(&im->sysconf.ddrlaw[0].bar,
+ CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000);
+ out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
+ out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+ out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+ out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
+
+ /* Currently we use only one CS, so disable the other bank. */
+ out_be32(&im->ddr.cs_config[1], 0);
+
+ out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL);
+ out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
+ out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
+ out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+ out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
+
+ out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ sync();
+
+ /* enable DDR controller */
+ setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+ sync();
+
+ return get_ram_size(CONFIG_SYS_DDR_SDRAM_BASE, msize);
+}
+
+phys_size_t initdram(int board_type)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize;
+
+ if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ /* DDR SDRAM */
+ msize = fixed_sdram();
+
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize;
+}
diff --git a/boards.cfg b/boards.cfg
index 05ddb8c..b9d4a77 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -334,6 +334,7 @@ ppmc8260 powerpc mpc8260
RPXsuper powerpc mpc8260 rpxsuper
rsdproto powerpc mpc8260
MPC8266ADS powerpc mpc8260 mpc8266ads freescale
+mpc8308_p1m powerpc mpc83xx
MPC8308RDB powerpc mpc83xx mpc8308rdb freescale
MPC8323ERDB powerpc mpc83xx mpc8323erdb freescale
MPC8349EMDS powerpc mpc83xx mpc8349emds freescale
diff --git a/include/configs/mpc8308_p1m.h b/include/configs/mpc8308_p1m.h
new file mode 100644
index 0000000..0f8270b
--- /dev/null
+++ b/include/configs/mpc8308_p1m.h
@@ -0,0 +1,555 @@
+/*
+ * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok at emcraft.com
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_MPC83xx 1 /* MPC83xx family */
+#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
+#define CONFIG_MPC8308_P1M 1 /* mpc8308_p1m board specific */
+
+/*
+ * On-board devices
+ *
+ * TSECs
+ */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC2
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.66MHz, then
+ * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
+ * We choose the A type silicon as default, so the core is 400Mhz.
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_SVCOD_DIV_2 |\
+ HRCWL_CSB_TO_CLKIN_4X1 |\
+ HRCWL_CORE_TO_CSB_3X1)
+/*
+ * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
+ * in 8308's HRCWH according to the manual, but original Freescale's
+ * code has them and I've expirienced some problems using the board
+ * with BDI3000 attached when I've tried to set these bits to zero
+ * (UART doesn't work after the 'reset run' command).
+ */
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_RL_EXT_LEGACY |\
+ HRCWH_TSEC1M_IN_MII |\
+ HRCWH_TSEC2M_IN_MII |\
+ HRCWH_BIG_ENDIAN)
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRH (\
+ SICRH_ESDHC_A_GPIO |\
+ SICRH_ESDHC_B_GPIO |\
+ SICRH_ESDHC_C_GTM |\
+ SICRH_GPIO_A_TSEC2 |\
+ SICRH_GPIO_B_TSEC2_TX_CLK |\
+ SICRH_IEEE1588_A_GPIO |\
+ SICRH_USB |\
+ SICRH_GTM_GPIO |\
+ SICRH_IEEE1588_B_GPIO |\
+ SICRH_ETSEC2_CRS |\
+ SICRH_GPIOSEL_1 |\
+ SICRH_TMROBI_V3P3 |\
+ SICRH_TSOBI1_V3P3 |\
+ SICRH_TSOBI2_V3P3) /* 0xf577d100 */
+#define CONFIG_SYS_SICRL (\
+ SICRL_SPI_PF0 |\
+ SICRL_UART_PF0 |\
+ SICRL_IRQ_PF0 |\
+ SICRL_I2C2_PF0 |\
+ SICRL_ETSEC1_TX_CLK) /* 0x00000000 */
+
+#define CONFIG_SYS_GPIO1_PRELIM
+/* GPIO Default input/output settings */
+#define CONFIG_SYS_GPIO1_DIR 0x7AAF8C00
+/*
+ * Default GPIO values:
+ * LED#1 enabled; WLAN enabled; Both COM LED on (orange)
+ */
+#define CONFIG_SYS_GPIO1_DAT 0x08008C00
+
+/*
+ * IMMR new address
+ */
+#define CONFIG_SYS_IMMR 0xE0000000
+
+/*
+ * SERDES
+ */
+#define CONFIG_FSL_SERDES
+#define CONFIG_FSL_SERDES1 0xe3000
+
+/*
+ * Arbiter Setup
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
+#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
+ | DDRCDR_PZ_LOZ \
+ | DDRCDR_NZ_LOZ \
+ | DDRCDR_ODT \
+ | DDRCDR_Q_DRN)
+ /* 0x7b880001 */
+/*
+ * Manually set up DDR parameters
+ * consist of two chips HY5PS12621BFP-C4 from HYNIX
+ */
+
+#define CONFIG_SYS_DDR_SIZE 128 /* MB */
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
+ | 0x00010000 /* ODT_WR to CSn */ \
+ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+ /* 0x80010102 */
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
+ | (0 << TIMING_CFG0_WRT_SHIFT) \
+ | (0 << TIMING_CFG0_RRT_SHIFT) \
+ | (0 << TIMING_CFG0_WWT_SHIFT) \
+ | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
+ | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+ /* 0x00220802 */
+#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
+ | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
+ | (5 << TIMING_CFG1_CASLAT_SHIFT) \
+ | (6 << TIMING_CFG1_REFREC_SHIFT) \
+ | (2 << TIMING_CFG1_WRREC_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
+ | (2 << TIMING_CFG1_WRTORD_SHIFT))
+ /* 0x27256222 */
+#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
+ | (4 << TIMING_CFG2_CPO_SHIFT) \
+ | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
+ | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
+ | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
+ | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
+ | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
+ /* 0x121048c5 */
+#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
+ | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+ /* 0x03600100 */
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
+ | SDRAM_CFG_SDRAM_TYPE_DDR2 \
+ | SDRAM_CFG_32_BE)
+ /* 0x43080000 */
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
+#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
+ | (0x0232 << SDRAM_MODE_SD_SHIFT))
+ /* ODT 150ohm CL=3, AL=1 on SDRAM */
+#define CONFIG_SYS_DDR_MODE2 0x00000000
+
+/*
+ * Memory test
+ */
+#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x07f00000
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR 0x00040000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+
+#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
+
+/* Window base@flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB)
+
+#define CONFIG_SYS_BR0_PRELIM (\
+ CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\
+ (2 << BR_PS_SHIFT) /* 16 bit port size */ |\
+ BR_V) /* valid */
+#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \
+ | OR_UPM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_4 \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512
+
+/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024)
+/* Flash Write Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024)
+
+/*
+ * SJA1000 CAN controller on Local Bus
+ */
+#define CONFIG_SYS_SJA1000_BASE 0xFBFF0000
+#define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_SJA1000_BASE \
+ | (1 << BR_PS_SHIFT) /* 8 bit port size */ \
+ | BR_V ) /* valid */
+#define CONFIG_SYS_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_GPCM_SCY_5 \
+ | OR_GPCM_EHTR)
+ /* 0xFFFF8052 */
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
+
+/*
+ * CPLD on Local Bus
+ */
+#define CONFIG_SYS_CPLD_BASE 0xFBFF8000
+#define CONFIG_SYS_BR2_PRELIM ( CONFIG_SYS_CPLD_BASE \
+ | (1 << BR_PS_SHIFT) /* 8 bit port size */ \
+ | BR_V ) /* valid */
+#define CONFIG_SYS_OR2_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_GPCM_SCY_4 \
+ | OR_GPCM_EHTR)
+ /* 0xFFFF8042 */
+
+#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCIE1_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
+#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
+#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
+#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
+
+/* enable PCIE clock */
+#define CONFIG_SYS_SCCR_PCIEXP1CM 1
+
+#define CONFIG_PCI
+#define CONFIG_PCIE
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
+
+/*
+ * TSEC
+ */
+#define CONFIG_NET_MULTI
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
+
+/*
+ * TSEC ethernet configuration
+ */
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_TSEC1_NAME "eTSEC0"
+#define CONFIG_TSEC2_NAME "eTSEC1"
+#define TSEC1_PHY_ADDR 1
+#define TSEC2_PHY_ADDR 2
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS 0
+#define TSEC2_FLAGS 0
+
+/* Options are: eTSEC[0-1] */
+#define CONFIG_ETHPRIME "eTSEC0"
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
+ CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+ HID0_ENABLE_INSTRUCTION_CACHE | \
+ HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
+#define CONFIG_SYS_HID2 HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+
+/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
+ BATU_VP)
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | \
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
+
+#define xstr(s) str(s)
+#define str(s) #s
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs}" \
+ " console=${consoledev},${baudrate}\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addmisc=setenv bootargs ${bootargs}\0" \
+ "kernel_addr=FC0A0000\0" \
+ "fdt_addr=FC2A0000\0" \
+ "ramdisk_addr=FC2C0000\0" \
+ "u-boot=mpc8308_p1m/u-boot.bin\0" \
+ "kernel_addr_r=1000000\0" \
+ "fdt_addr_r=C00000\0" \
+ "hostname=mpc8308_p1m\0" \
+ "bootfile=mpc8308_p1m/uImage\0" \
+ "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \
+ "rootpath=/opt/eldk-4.2/ppc_6xx\0" \
+ "flash_self=run ramargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
+ "tftp ${fdt_addr_r} ${fdtfile};" \
+ "run nfsargs addip addtty addmtd addmisc;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
+ "bootcmd=run flash_self\0" \
+ "load=tftp ${loadaddr} ${u-boot}\0" \
+ "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};cp.b ${fileaddr} " \
+ xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
+ "upd=run load update\0" \
+
+#endif /* __CONFIG_H */
--
1.6.2.5
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH][v3] mpc8308_p1m: support for MPC8308 P1M board
2010-09-14 1:12 ` Kim Phillips
2010-09-14 20:40 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Ilya Yanok
@ 2010-09-18 20:35 ` Wolfgang Denk
2010-09-20 16:18 ` Scott Wood
1 sibling, 1 reply; 23+ messages in thread
From: Wolfgang Denk @ 2010-09-18 20:35 UTC (permalink / raw)
To: u-boot
Dear Kim Phillips,
In message <20100913201208.461501b3.kim.phillips@freescale.com> you wrote:
>
> > MAINTAINERS | 1 +
> > board/mpc8308_p1m/Makefile | 52 ++++
> > board/mpc8308_p1m/config.mk | 1 +
> > board/mpc8308_p1m/mpc8308_p1m.c | 122 +++++++++
> > board/mpc8308_p1m/sdram.c | 93 +++++++
> > boards.cfg | 1 +
> > include/configs/mpc8308_p1m.h | 548 +++++++++++++++++++++++++++++++++++++++
>
> missing MAKEALL entry.
Not needed any more since we pick this off from boards.cfg for
"simple" boards.
> > +++ b/board/mpc8308_p1m/config.mk
> > @@ -0,0 +1 @@
> > +TEXT_BASE = 0xFC000000
>
> ifndef TEXT_BASE
> TEXT_BASE = 0xFC000000
> endif
Why?
> > +int board_eth_init(bd_t *bis)
> > +{
> > + int rv, num_if = 0;
> > +
> > + /* Initialize TSECs first */
> > + if ((rv = cpu_eth_init(bis)) >= 0)
>
> no assignments in if statements.
Why?
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Never ascribe to malice that which can adequately be explained by
stupidity.
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH][v3] mpc8308_p1m: support for MPC8308 P1M board
2010-09-18 20:35 ` [U-Boot] [PATCH][v3] " Wolfgang Denk
@ 2010-09-20 16:18 ` Scott Wood
2010-09-20 16:42 ` Wolfgang Denk
0 siblings, 1 reply; 23+ messages in thread
From: Scott Wood @ 2010-09-20 16:18 UTC (permalink / raw)
To: u-boot
On Sat, 18 Sep 2010 22:35:54 +0200
Wolfgang Denk <wd@denx.de> wrote:
> > > +++ b/board/mpc8308_p1m/config.mk
> > > @@ -0,0 +1 @@
> > > +TEXT_BASE = 0xFC000000
> >
> > ifndef TEXT_BASE
> > TEXT_BASE = 0xFC000000
> > endif
>
> Why?
It might have been already set to something else by nand_spl or
similar.
> > > +int board_eth_init(bd_t *bis)
> > > +{
> > > + int rv, num_if = 0;
> > > +
> > > + /* Initialize TSECs first */
> > > + if ((rv = cpu_eth_init(bis)) >= 0)
> >
> > no assignments in if statements.
>
> Why?
It could just as easily, and more readably, be written as:
rv = cpu_eth_init(bis);
if (rv >= 0)
...
FWIW, Linux's checkpatch.pl looks for this and calls it an error, and
U-Boot says it follows Linux coding style.
-Scott
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH][v3] mpc8308_p1m: support for MPC8308 P1M board
2010-09-20 16:18 ` Scott Wood
@ 2010-09-20 16:42 ` Wolfgang Denk
2010-09-20 23:56 ` Kim Phillips
0 siblings, 1 reply; 23+ messages in thread
From: Wolfgang Denk @ 2010-09-20 16:42 UTC (permalink / raw)
To: u-boot
Dear Scott Wood,
In message <20100920111852.0cc76594@udp111988uds.am.freescale.net> you wrote:
> > > ifndef TEXT_BASE
> > > TEXT_BASE = 0xFC000000
> > > endif
> >
> > Why?
>
> It might have been already set to something else by nand_spl or
> similar.
No. There is no NAND on that board.
> > > no assignments in if statements.
> >
> > Why?
>
> It could just as easily, and more readably, be written as:
>
> rv = cpu_eth_init(bis);
> if (rv >= 0)
> ...
It depends whether you call that more readable. The UNIX code where I
learned C was full of that, and I find it actually easier to read.
> FWIW, Linux's checkpatch.pl looks for this and calls it an error, and
> U-Boot says it follows Linux coding style.
OK, that's an argument.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"The value of marriage is not that adults produce children, but that
children produce adults." - Peter De Vries
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH][v3] mpc8308_p1m: support for MPC8308 P1M board
2010-09-20 16:42 ` Wolfgang Denk
@ 2010-09-20 23:56 ` Kim Phillips
0 siblings, 0 replies; 23+ messages in thread
From: Kim Phillips @ 2010-09-20 23:56 UTC (permalink / raw)
To: u-boot
On Mon, 20 Sep 2010 18:42:27 +0200
Wolfgang Denk <wd@denx.de> wrote:
> In message <20100920111852.0cc76594@udp111988uds.am.freescale.net> you wrote:
> > > > ifndef TEXT_BASE
> > > > TEXT_BASE = 0xFC000000
> > > > endif
> > >
> > > Why?
> >
> > It might have been already set to something else by nand_spl or
> > similar.
>
> No. There is no NAND on that board.
it's consistent with other board ports, and there may be a derivative
board port with NAND, or some other boot source.
btw, subsequent versions of this patch have the ifndef added...
Kim
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured
2010-09-17 21:41 ` Ilya Yanok
@ 2010-09-22 21:02 ` Kim Phillips
0 siblings, 0 replies; 23+ messages in thread
From: Kim Phillips @ 2010-09-22 21:02 UTC (permalink / raw)
To: u-boot
On Fri, 17 Sep 2010 23:41:46 +0200
Ilya Yanok <yanok@emcraft.com> wrote:
> MPC8308 has only one PCIE host controller so we want it to compile
> without CONFIG_SYS_PCIE2_CFG_{BASE,SIZE} defined.
>
> Signed-off-by: Ilya Yanok <yanok@emcraft.com>
> ---
5 out of 5 patches applied to u-boot-mpc83xx/next.
one more added:
^ permalink raw reply [flat|nested] 23+ messages in thread
end of thread, other threads:[~2010-09-22 21:02 UTC | newest]
Thread overview: 23+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-08-25 14:00 [U-Boot] [PATCH] mpc8308_p1m: support for MPC8308 P1M board Ilya Yanok
2010-09-06 10:32 ` [U-Boot] [PATCH][v2] " Ilya Yanok
2010-09-07 21:47 ` Scott Wood
2010-09-08 21:36 ` [U-Boot] [PATCH][v3] " Ilya Yanok
2010-09-14 1:12 ` Kim Phillips
2010-09-14 20:40 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Ilya Yanok
2010-09-14 20:40 ` [U-Boot] [PATCH 2/5] mpc83xx: add support for setting PCIE clocks Ilya Yanok
2010-09-14 20:40 ` [U-Boot] [PATCH 3/5] mpc8308: add SICR{L,H} fields definitions Ilya Yanok
2010-09-14 20:40 ` [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups Ilya Yanok
2010-09-14 20:40 ` [U-Boot] [PATCH 5/5] mpc8308_p1m: support for MPC8308 P1M board Ilya Yanok
2010-09-16 23:56 ` [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups Kim Phillips
2010-09-16 23:54 ` [U-Boot] [PATCH 1/5] mpc83xx/pcie: make it compile with PCIE2 unconfigured Kim Phillips
2010-09-17 21:35 ` Ilya Yanok
2010-09-17 21:41 ` Ilya Yanok
2010-09-22 21:02 ` Kim Phillips
2010-09-17 21:41 ` [U-Boot] [PATCH 2/5] mpc83xx: add support for setting PCIE clocks Ilya Yanok
2010-09-17 21:41 ` [U-Boot] [PATCH 3/5] mpc8308: add SICR{L,H} fields definitions Ilya Yanok
2010-09-17 21:41 ` [U-Boot] [PATCH 4/5] MPC8308RDB: various clean ups Ilya Yanok
2010-09-17 21:41 ` [U-Boot] [PATCH 5/5] mpc8308_p1m: support for MPC8308 P1M board Ilya Yanok
2010-09-18 20:35 ` [U-Boot] [PATCH][v3] " Wolfgang Denk
2010-09-20 16:18 ` Scott Wood
2010-09-20 16:42 ` Wolfgang Denk
2010-09-20 23:56 ` Kim Phillips
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.