* [PATCH v4 0/9] Use regmap+devm+DT in pm8xxx input drivers
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: linux-arm-kernel
These patches move the pm8xxx input drivers over to use devm_* APIs
and regmap. This breaks the dependency of these drivers on the pm8xxx
specific read/write calls and also simplifies the probe code a bit.
Finally we add devicetree support to these drivers so they can be probed
on the platforms that are supported upstream.
Changes since v3:
* Dropped devm conversion patch for pwrkey
* Fixed compilation of keypad
Changes since v2:
* Rebased to v3.14-rc3
Changes since v1:
* Picked up Dmitry's version of devm for pwrkey
* Added DT bindings and parsing patches
* Dropped patches picked up by Dmitry
Stephen Boyd (9):
Input: pmic8xxx-keypad - Fix build by removing gpio configuration
Input: pmic8xxx-keypad - Migrate to devm_* APIs
Input: pmic8xxx-keypad - Migrate to regmap APIs
Input: pmic8xxx-keypad - Migrate to DT
Input: pmic8xxx-pwrkey - Migrate to DT
Input: pm8xxx-vibrator - Add DT match table
devicetree: bindings: Document PM8921/8058 keypads
devicetree: bindings: Document PM8921/8058 power keys
devicetree: bindings: Document PM8921/8058 vibrators
.../bindings/input/qcom,pm8xxx-keypad.txt | 72 +++++
.../bindings/input/qcom,pm8xxx-pwrkey.txt | 39 +++
.../devicetree/bindings/input/qcom,pm8xxx-vib.txt | 16 +
drivers/input/keyboard/pmic8xxx-keypad.c | 348 ++++++++-------------
drivers/input/misc/pm8xxx-vibrator.c | 8 +
drivers/input/misc/pmic8xxx-pwrkey.c | 33 +-
include/linux/input/pmic8xxx-keypad.h | 52 ---
include/linux/input/pmic8xxx-pwrkey.h | 31 --
8 files changed, 286 insertions(+), 313 deletions(-)
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt
delete mode 100644 include/linux/input/pmic8xxx-keypad.h
delete mode 100644 include/linux/input/pmic8xxx-pwrkey.h
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v4 0/9] Use regmap+devm+DT in pm8xxx input drivers
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input, devicetree
These patches move the pm8xxx input drivers over to use devm_* APIs
and regmap. This breaks the dependency of these drivers on the pm8xxx
specific read/write calls and also simplifies the probe code a bit.
Finally we add devicetree support to these drivers so they can be probed
on the platforms that are supported upstream.
Changes since v3:
* Dropped devm conversion patch for pwrkey
* Fixed compilation of keypad
Changes since v2:
* Rebased to v3.14-rc3
Changes since v1:
* Picked up Dmitry's version of devm for pwrkey
* Added DT bindings and parsing patches
* Dropped patches picked up by Dmitry
Stephen Boyd (9):
Input: pmic8xxx-keypad - Fix build by removing gpio configuration
Input: pmic8xxx-keypad - Migrate to devm_* APIs
Input: pmic8xxx-keypad - Migrate to regmap APIs
Input: pmic8xxx-keypad - Migrate to DT
Input: pmic8xxx-pwrkey - Migrate to DT
Input: pm8xxx-vibrator - Add DT match table
devicetree: bindings: Document PM8921/8058 keypads
devicetree: bindings: Document PM8921/8058 power keys
devicetree: bindings: Document PM8921/8058 vibrators
.../bindings/input/qcom,pm8xxx-keypad.txt | 72 +++++
.../bindings/input/qcom,pm8xxx-pwrkey.txt | 39 +++
.../devicetree/bindings/input/qcom,pm8xxx-vib.txt | 16 +
drivers/input/keyboard/pmic8xxx-keypad.c | 348 ++++++++-------------
drivers/input/misc/pm8xxx-vibrator.c | 8 +
drivers/input/misc/pmic8xxx-pwrkey.c | 33 +-
include/linux/input/pmic8xxx-keypad.h | 52 ---
include/linux/input/pmic8xxx-pwrkey.h | 31 --
8 files changed, 286 insertions(+), 313 deletions(-)
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt
delete mode 100644 include/linux/input/pmic8xxx-keypad.h
delete mode 100644 include/linux/input/pmic8xxx-pwrkey.h
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v4 1/9] Input: pmic8xxx-keypad - Fix build by removing gpio configuration
2014-02-28 1:55 ` Stephen Boyd
@ 2014-02-28 1:55 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input
The gpio configuration in this driver doesn't work because the
gpio.h include doesn't exist. Remove the configuration as it
isn't strictly necessary, allowing us to actually compile this
driver. If it's needed in the future, it should be done via a
pinctrl driver.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/keyboard/pmic8xxx-keypad.c | 58 --------------------------------
1 file changed, 58 deletions(-)
diff --git a/drivers/input/keyboard/pmic8xxx-keypad.c b/drivers/input/keyboard/pmic8xxx-keypad.c
index 2c9f19ac35ea..c4aa882c8fb9 100644
--- a/drivers/input/keyboard/pmic8xxx-keypad.c
+++ b/drivers/input/keyboard/pmic8xxx-keypad.c
@@ -21,7 +21,6 @@
#include <linux/mutex.h>
#include <linux/mfd/pm8xxx/core.h>
-#include <linux/mfd/pm8xxx/gpio.h>
#include <linux/input/pmic8xxx-keypad.h>
#define PM8XXX_MAX_ROWS 18
@@ -447,27 +446,6 @@ static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
}
-static int pmic8xxx_kp_config_gpio(int gpio_start, int num_gpios,
- struct pmic8xxx_kp *kp, struct pm_gpio *gpio_config)
-{
- int rc, i;
-
- if (gpio_start < 0 || num_gpios < 0)
- return -EINVAL;
-
- for (i = 0; i < num_gpios; i++) {
- rc = pm8xxx_gpio_config(gpio_start + i, gpio_config);
- if (rc) {
- dev_err(kp->dev, "%s: FAIL pm8xxx_gpio_config():"
- "for PM GPIO [%d] rc=%d.\n",
- __func__, gpio_start + i, rc);
- return rc;
- }
- }
-
- return 0;
-}
-
static int pmic8xxx_kp_enable(struct pmic8xxx_kp *kp)
{
int rc;
@@ -527,27 +505,6 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
int rc;
u8 ctrl_val;
- struct pm_gpio kypd_drv = {
- .direction = PM_GPIO_DIR_OUT,
- .output_buffer = PM_GPIO_OUT_BUF_OPEN_DRAIN,
- .output_value = 0,
- .pull = PM_GPIO_PULL_NO,
- .vin_sel = PM_GPIO_VIN_S3,
- .out_strength = PM_GPIO_STRENGTH_LOW,
- .function = PM_GPIO_FUNC_1,
- .inv_int_pol = 1,
- };
-
- struct pm_gpio kypd_sns = {
- .direction = PM_GPIO_DIR_IN,
- .pull = PM_GPIO_PULL_UP_31P5,
- .vin_sel = PM_GPIO_VIN_S3,
- .out_strength = PM_GPIO_STRENGTH_NO,
- .function = PM_GPIO_FUNC_NORMAL,
- .inv_int_pol = 1,
- };
-
-
if (!pdata || !pdata->num_cols || !pdata->num_rows ||
pdata->num_cols > PM8XXX_MAX_COLS ||
pdata->num_rows > PM8XXX_MAX_ROWS ||
@@ -653,20 +610,6 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
goto err_get_irq;
}
- rc = pmic8xxx_kp_config_gpio(pdata->cols_gpio_start,
- pdata->num_cols, kp, &kypd_sns);
- if (rc < 0) {
- dev_err(&pdev->dev, "unable to configure keypad sense lines\n");
- goto err_gpio_config;
- }
-
- rc = pmic8xxx_kp_config_gpio(pdata->rows_gpio_start,
- pdata->num_rows, kp, &kypd_drv);
- if (rc < 0) {
- dev_err(&pdev->dev, "unable to configure keypad drive lines\n");
- goto err_gpio_config;
- }
-
rc = request_any_context_irq(kp->key_sense_irq, pmic8xxx_kp_irq,
IRQF_TRIGGER_RISING, "pmic-keypad", kp);
if (rc < 0) {
@@ -703,7 +646,6 @@ err_pmic_reg_read:
free_irq(kp->key_stuck_irq, kp);
err_req_stuck_irq:
free_irq(kp->key_sense_irq, kp);
-err_gpio_config:
err_get_irq:
input_free_device(kp->input);
err_alloc_device:
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 1/9] Input: pmic8xxx-keypad - Fix build by removing gpio configuration
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: linux-arm-kernel
The gpio configuration in this driver doesn't work because the
gpio.h include doesn't exist. Remove the configuration as it
isn't strictly necessary, allowing us to actually compile this
driver. If it's needed in the future, it should be done via a
pinctrl driver.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/keyboard/pmic8xxx-keypad.c | 58 --------------------------------
1 file changed, 58 deletions(-)
diff --git a/drivers/input/keyboard/pmic8xxx-keypad.c b/drivers/input/keyboard/pmic8xxx-keypad.c
index 2c9f19ac35ea..c4aa882c8fb9 100644
--- a/drivers/input/keyboard/pmic8xxx-keypad.c
+++ b/drivers/input/keyboard/pmic8xxx-keypad.c
@@ -21,7 +21,6 @@
#include <linux/mutex.h>
#include <linux/mfd/pm8xxx/core.h>
-#include <linux/mfd/pm8xxx/gpio.h>
#include <linux/input/pmic8xxx-keypad.h>
#define PM8XXX_MAX_ROWS 18
@@ -447,27 +446,6 @@ static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
}
-static int pmic8xxx_kp_config_gpio(int gpio_start, int num_gpios,
- struct pmic8xxx_kp *kp, struct pm_gpio *gpio_config)
-{
- int rc, i;
-
- if (gpio_start < 0 || num_gpios < 0)
- return -EINVAL;
-
- for (i = 0; i < num_gpios; i++) {
- rc = pm8xxx_gpio_config(gpio_start + i, gpio_config);
- if (rc) {
- dev_err(kp->dev, "%s: FAIL pm8xxx_gpio_config():"
- "for PM GPIO [%d] rc=%d.\n",
- __func__, gpio_start + i, rc);
- return rc;
- }
- }
-
- return 0;
-}
-
static int pmic8xxx_kp_enable(struct pmic8xxx_kp *kp)
{
int rc;
@@ -527,27 +505,6 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
int rc;
u8 ctrl_val;
- struct pm_gpio kypd_drv = {
- .direction = PM_GPIO_DIR_OUT,
- .output_buffer = PM_GPIO_OUT_BUF_OPEN_DRAIN,
- .output_value = 0,
- .pull = PM_GPIO_PULL_NO,
- .vin_sel = PM_GPIO_VIN_S3,
- .out_strength = PM_GPIO_STRENGTH_LOW,
- .function = PM_GPIO_FUNC_1,
- .inv_int_pol = 1,
- };
-
- struct pm_gpio kypd_sns = {
- .direction = PM_GPIO_DIR_IN,
- .pull = PM_GPIO_PULL_UP_31P5,
- .vin_sel = PM_GPIO_VIN_S3,
- .out_strength = PM_GPIO_STRENGTH_NO,
- .function = PM_GPIO_FUNC_NORMAL,
- .inv_int_pol = 1,
- };
-
-
if (!pdata || !pdata->num_cols || !pdata->num_rows ||
pdata->num_cols > PM8XXX_MAX_COLS ||
pdata->num_rows > PM8XXX_MAX_ROWS ||
@@ -653,20 +610,6 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
goto err_get_irq;
}
- rc = pmic8xxx_kp_config_gpio(pdata->cols_gpio_start,
- pdata->num_cols, kp, &kypd_sns);
- if (rc < 0) {
- dev_err(&pdev->dev, "unable to configure keypad sense lines\n");
- goto err_gpio_config;
- }
-
- rc = pmic8xxx_kp_config_gpio(pdata->rows_gpio_start,
- pdata->num_rows, kp, &kypd_drv);
- if (rc < 0) {
- dev_err(&pdev->dev, "unable to configure keypad drive lines\n");
- goto err_gpio_config;
- }
-
rc = request_any_context_irq(kp->key_sense_irq, pmic8xxx_kp_irq,
IRQF_TRIGGER_RISING, "pmic-keypad", kp);
if (rc < 0) {
@@ -703,7 +646,6 @@ err_pmic_reg_read:
free_irq(kp->key_stuck_irq, kp);
err_req_stuck_irq:
free_irq(kp->key_sense_irq, kp);
-err_gpio_config:
err_get_irq:
input_free_device(kp->input);
err_alloc_device:
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v4 2/9] Input: pmic8xxx-keypad - Migrate to devm_* APIs
2014-02-28 1:55 ` Stephen Boyd
(?)
@ 2014-02-28 1:55 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-arm-msm, Josh Cartwright, linux-kernel, linux-arm-kernel,
linux-input
Simplify the error paths and reduce the lines of code in this
driver by using the devm_* APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/keyboard/pmic8xxx-keypad.c | 61 +++++++++-----------------------
1 file changed, 17 insertions(+), 44 deletions(-)
diff --git a/drivers/input/keyboard/pmic8xxx-keypad.c b/drivers/input/keyboard/pmic8xxx-keypad.c
index c4aa882c8fb9..bec53ebde7b2 100644
--- a/drivers/input/keyboard/pmic8xxx-keypad.c
+++ b/drivers/input/keyboard/pmic8xxx-keypad.c
@@ -543,7 +543,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
return -EINVAL;
}
- kp = kzalloc(sizeof(*kp), GFP_KERNEL);
+ kp = devm_kzalloc(&pdev->dev, sizeof(*kp), GFP_KERNEL);
if (!kp)
return -ENOMEM;
@@ -552,32 +552,27 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
kp->pdata = pdata;
kp->dev = &pdev->dev;
- kp->input = input_allocate_device();
+ kp->input = devm_input_allocate_device(&pdev->dev);
if (!kp->input) {
dev_err(&pdev->dev, "unable to allocate input device\n");
- rc = -ENOMEM;
- goto err_alloc_device;
+ return -ENOMEM;
}
kp->key_sense_irq = platform_get_irq(pdev, 0);
if (kp->key_sense_irq < 0) {
dev_err(&pdev->dev, "unable to get keypad sense irq\n");
- rc = -ENXIO;
- goto err_get_irq;
+ return kp->key_sense_irq;
}
kp->key_stuck_irq = platform_get_irq(pdev, 1);
if (kp->key_stuck_irq < 0) {
dev_err(&pdev->dev, "unable to get keypad stuck irq\n");
- rc = -ENXIO;
- goto err_get_irq;
+ return kp->key_stuck_irq;
}
kp->input->name = pdata->input_name ? : "PMIC8XXX keypad";
kp->input->phys = pdata->input_phys_device ? : "pmic8xxx_keypad/input0";
- kp->input->dev.parent = &pdev->dev;
-
kp->input->id.bustype = BUS_I2C;
kp->input->id.version = 0x0001;
kp->input->id.product = 0x0001;
@@ -591,7 +586,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
kp->keycodes, kp->input);
if (rc) {
dev_err(&pdev->dev, "failed to build keymap\n");
- goto err_get_irq;
+ return rc;
}
if (pdata->rep)
@@ -607,27 +602,29 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
rc = pmic8xxx_kpd_init(kp);
if (rc < 0) {
dev_err(&pdev->dev, "unable to initialize keypad controller\n");
- goto err_get_irq;
+ return rc;
}
- rc = request_any_context_irq(kp->key_sense_irq, pmic8xxx_kp_irq,
- IRQF_TRIGGER_RISING, "pmic-keypad", kp);
+ rc = devm_request_any_context_irq(&pdev->dev, kp->key_sense_irq,
+ pmic8xxx_kp_irq, IRQF_TRIGGER_RISING, "pmic-keypad",
+ kp);
if (rc < 0) {
dev_err(&pdev->dev, "failed to request keypad sense irq\n");
- goto err_get_irq;
+ return rc;
}
- rc = request_any_context_irq(kp->key_stuck_irq, pmic8xxx_kp_stuck_irq,
- IRQF_TRIGGER_RISING, "pmic-keypad-stuck", kp);
+ rc = devm_request_any_context_irq(&pdev->dev, kp->key_stuck_irq,
+ pmic8xxx_kp_stuck_irq, IRQF_TRIGGER_RISING,
+ "pmic-keypad-stuck", kp);
if (rc < 0) {
dev_err(&pdev->dev, "failed to request keypad stuck irq\n");
- goto err_req_stuck_irq;
+ return rc;
}
rc = pmic8xxx_kp_read_u8(kp, &ctrl_val, KEYP_CTRL);
if (rc < 0) {
dev_err(&pdev->dev, "failed to read KEYP_CTRL register\n");
- goto err_pmic_reg_read;
+ return rc;
}
kp->ctrl_reg = ctrl_val;
@@ -635,35 +632,12 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
rc = input_register_device(kp->input);
if (rc < 0) {
dev_err(&pdev->dev, "unable to register keypad input device\n");
- goto err_pmic_reg_read;
+ return rc;
}
device_init_wakeup(&pdev->dev, pdata->wakeup);
return 0;
-
-err_pmic_reg_read:
- free_irq(kp->key_stuck_irq, kp);
-err_req_stuck_irq:
- free_irq(kp->key_sense_irq, kp);
-err_get_irq:
- input_free_device(kp->input);
-err_alloc_device:
- kfree(kp);
- return rc;
-}
-
-static int pmic8xxx_kp_remove(struct platform_device *pdev)
-{
- struct pmic8xxx_kp *kp = platform_get_drvdata(pdev);
-
- device_init_wakeup(&pdev->dev, 0);
- free_irq(kp->key_stuck_irq, kp);
- free_irq(kp->key_sense_irq, kp);
- input_unregister_device(kp->input);
- kfree(kp);
-
- return 0;
}
#ifdef CONFIG_PM_SLEEP
@@ -713,7 +687,6 @@ static SIMPLE_DEV_PM_OPS(pm8xxx_kp_pm_ops,
static struct platform_driver pmic8xxx_kp_driver = {
.probe = pmic8xxx_kp_probe,
- .remove = pmic8xxx_kp_remove,
.driver = {
.name = PM8XXX_KEYPAD_DEV_NAME,
.owner = THIS_MODULE,
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 2/9] Input: pmic8xxx-keypad - Migrate to devm_* APIs
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: linux-arm-kernel
Simplify the error paths and reduce the lines of code in this
driver by using the devm_* APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/keyboard/pmic8xxx-keypad.c | 61 +++++++++-----------------------
1 file changed, 17 insertions(+), 44 deletions(-)
diff --git a/drivers/input/keyboard/pmic8xxx-keypad.c b/drivers/input/keyboard/pmic8xxx-keypad.c
index c4aa882c8fb9..bec53ebde7b2 100644
--- a/drivers/input/keyboard/pmic8xxx-keypad.c
+++ b/drivers/input/keyboard/pmic8xxx-keypad.c
@@ -543,7 +543,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
return -EINVAL;
}
- kp = kzalloc(sizeof(*kp), GFP_KERNEL);
+ kp = devm_kzalloc(&pdev->dev, sizeof(*kp), GFP_KERNEL);
if (!kp)
return -ENOMEM;
@@ -552,32 +552,27 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
kp->pdata = pdata;
kp->dev = &pdev->dev;
- kp->input = input_allocate_device();
+ kp->input = devm_input_allocate_device(&pdev->dev);
if (!kp->input) {
dev_err(&pdev->dev, "unable to allocate input device\n");
- rc = -ENOMEM;
- goto err_alloc_device;
+ return -ENOMEM;
}
kp->key_sense_irq = platform_get_irq(pdev, 0);
if (kp->key_sense_irq < 0) {
dev_err(&pdev->dev, "unable to get keypad sense irq\n");
- rc = -ENXIO;
- goto err_get_irq;
+ return kp->key_sense_irq;
}
kp->key_stuck_irq = platform_get_irq(pdev, 1);
if (kp->key_stuck_irq < 0) {
dev_err(&pdev->dev, "unable to get keypad stuck irq\n");
- rc = -ENXIO;
- goto err_get_irq;
+ return kp->key_stuck_irq;
}
kp->input->name = pdata->input_name ? : "PMIC8XXX keypad";
kp->input->phys = pdata->input_phys_device ? : "pmic8xxx_keypad/input0";
- kp->input->dev.parent = &pdev->dev;
-
kp->input->id.bustype = BUS_I2C;
kp->input->id.version = 0x0001;
kp->input->id.product = 0x0001;
@@ -591,7 +586,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
kp->keycodes, kp->input);
if (rc) {
dev_err(&pdev->dev, "failed to build keymap\n");
- goto err_get_irq;
+ return rc;
}
if (pdata->rep)
@@ -607,27 +602,29 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
rc = pmic8xxx_kpd_init(kp);
if (rc < 0) {
dev_err(&pdev->dev, "unable to initialize keypad controller\n");
- goto err_get_irq;
+ return rc;
}
- rc = request_any_context_irq(kp->key_sense_irq, pmic8xxx_kp_irq,
- IRQF_TRIGGER_RISING, "pmic-keypad", kp);
+ rc = devm_request_any_context_irq(&pdev->dev, kp->key_sense_irq,
+ pmic8xxx_kp_irq, IRQF_TRIGGER_RISING, "pmic-keypad",
+ kp);
if (rc < 0) {
dev_err(&pdev->dev, "failed to request keypad sense irq\n");
- goto err_get_irq;
+ return rc;
}
- rc = request_any_context_irq(kp->key_stuck_irq, pmic8xxx_kp_stuck_irq,
- IRQF_TRIGGER_RISING, "pmic-keypad-stuck", kp);
+ rc = devm_request_any_context_irq(&pdev->dev, kp->key_stuck_irq,
+ pmic8xxx_kp_stuck_irq, IRQF_TRIGGER_RISING,
+ "pmic-keypad-stuck", kp);
if (rc < 0) {
dev_err(&pdev->dev, "failed to request keypad stuck irq\n");
- goto err_req_stuck_irq;
+ return rc;
}
rc = pmic8xxx_kp_read_u8(kp, &ctrl_val, KEYP_CTRL);
if (rc < 0) {
dev_err(&pdev->dev, "failed to read KEYP_CTRL register\n");
- goto err_pmic_reg_read;
+ return rc;
}
kp->ctrl_reg = ctrl_val;
@@ -635,35 +632,12 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
rc = input_register_device(kp->input);
if (rc < 0) {
dev_err(&pdev->dev, "unable to register keypad input device\n");
- goto err_pmic_reg_read;
+ return rc;
}
device_init_wakeup(&pdev->dev, pdata->wakeup);
return 0;
-
-err_pmic_reg_read:
- free_irq(kp->key_stuck_irq, kp);
-err_req_stuck_irq:
- free_irq(kp->key_sense_irq, kp);
-err_get_irq:
- input_free_device(kp->input);
-err_alloc_device:
- kfree(kp);
- return rc;
-}
-
-static int pmic8xxx_kp_remove(struct platform_device *pdev)
-{
- struct pmic8xxx_kp *kp = platform_get_drvdata(pdev);
-
- device_init_wakeup(&pdev->dev, 0);
- free_irq(kp->key_stuck_irq, kp);
- free_irq(kp->key_sense_irq, kp);
- input_unregister_device(kp->input);
- kfree(kp);
-
- return 0;
}
#ifdef CONFIG_PM_SLEEP
@@ -713,7 +687,6 @@ static SIMPLE_DEV_PM_OPS(pm8xxx_kp_pm_ops,
static struct platform_driver pmic8xxx_kp_driver = {
.probe = pmic8xxx_kp_probe,
- .remove = pmic8xxx_kp_remove,
.driver = {
.name = PM8XXX_KEYPAD_DEV_NAME,
.owner = THIS_MODULE,
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 2/9] Input: pmic8xxx-keypad - Migrate to devm_* APIs
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input
Simplify the error paths and reduce the lines of code in this
driver by using the devm_* APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/keyboard/pmic8xxx-keypad.c | 61 +++++++++-----------------------
1 file changed, 17 insertions(+), 44 deletions(-)
diff --git a/drivers/input/keyboard/pmic8xxx-keypad.c b/drivers/input/keyboard/pmic8xxx-keypad.c
index c4aa882c8fb9..bec53ebde7b2 100644
--- a/drivers/input/keyboard/pmic8xxx-keypad.c
+++ b/drivers/input/keyboard/pmic8xxx-keypad.c
@@ -543,7 +543,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
return -EINVAL;
}
- kp = kzalloc(sizeof(*kp), GFP_KERNEL);
+ kp = devm_kzalloc(&pdev->dev, sizeof(*kp), GFP_KERNEL);
if (!kp)
return -ENOMEM;
@@ -552,32 +552,27 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
kp->pdata = pdata;
kp->dev = &pdev->dev;
- kp->input = input_allocate_device();
+ kp->input = devm_input_allocate_device(&pdev->dev);
if (!kp->input) {
dev_err(&pdev->dev, "unable to allocate input device\n");
- rc = -ENOMEM;
- goto err_alloc_device;
+ return -ENOMEM;
}
kp->key_sense_irq = platform_get_irq(pdev, 0);
if (kp->key_sense_irq < 0) {
dev_err(&pdev->dev, "unable to get keypad sense irq\n");
- rc = -ENXIO;
- goto err_get_irq;
+ return kp->key_sense_irq;
}
kp->key_stuck_irq = platform_get_irq(pdev, 1);
if (kp->key_stuck_irq < 0) {
dev_err(&pdev->dev, "unable to get keypad stuck irq\n");
- rc = -ENXIO;
- goto err_get_irq;
+ return kp->key_stuck_irq;
}
kp->input->name = pdata->input_name ? : "PMIC8XXX keypad";
kp->input->phys = pdata->input_phys_device ? : "pmic8xxx_keypad/input0";
- kp->input->dev.parent = &pdev->dev;
-
kp->input->id.bustype = BUS_I2C;
kp->input->id.version = 0x0001;
kp->input->id.product = 0x0001;
@@ -591,7 +586,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
kp->keycodes, kp->input);
if (rc) {
dev_err(&pdev->dev, "failed to build keymap\n");
- goto err_get_irq;
+ return rc;
}
if (pdata->rep)
@@ -607,27 +602,29 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
rc = pmic8xxx_kpd_init(kp);
if (rc < 0) {
dev_err(&pdev->dev, "unable to initialize keypad controller\n");
- goto err_get_irq;
+ return rc;
}
- rc = request_any_context_irq(kp->key_sense_irq, pmic8xxx_kp_irq,
- IRQF_TRIGGER_RISING, "pmic-keypad", kp);
+ rc = devm_request_any_context_irq(&pdev->dev, kp->key_sense_irq,
+ pmic8xxx_kp_irq, IRQF_TRIGGER_RISING, "pmic-keypad",
+ kp);
if (rc < 0) {
dev_err(&pdev->dev, "failed to request keypad sense irq\n");
- goto err_get_irq;
+ return rc;
}
- rc = request_any_context_irq(kp->key_stuck_irq, pmic8xxx_kp_stuck_irq,
- IRQF_TRIGGER_RISING, "pmic-keypad-stuck", kp);
+ rc = devm_request_any_context_irq(&pdev->dev, kp->key_stuck_irq,
+ pmic8xxx_kp_stuck_irq, IRQF_TRIGGER_RISING,
+ "pmic-keypad-stuck", kp);
if (rc < 0) {
dev_err(&pdev->dev, "failed to request keypad stuck irq\n");
- goto err_req_stuck_irq;
+ return rc;
}
rc = pmic8xxx_kp_read_u8(kp, &ctrl_val, KEYP_CTRL);
if (rc < 0) {
dev_err(&pdev->dev, "failed to read KEYP_CTRL register\n");
- goto err_pmic_reg_read;
+ return rc;
}
kp->ctrl_reg = ctrl_val;
@@ -635,35 +632,12 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
rc = input_register_device(kp->input);
if (rc < 0) {
dev_err(&pdev->dev, "unable to register keypad input device\n");
- goto err_pmic_reg_read;
+ return rc;
}
device_init_wakeup(&pdev->dev, pdata->wakeup);
return 0;
-
-err_pmic_reg_read:
- free_irq(kp->key_stuck_irq, kp);
-err_req_stuck_irq:
- free_irq(kp->key_sense_irq, kp);
-err_get_irq:
- input_free_device(kp->input);
-err_alloc_device:
- kfree(kp);
- return rc;
-}
-
-static int pmic8xxx_kp_remove(struct platform_device *pdev)
-{
- struct pmic8xxx_kp *kp = platform_get_drvdata(pdev);
-
- device_init_wakeup(&pdev->dev, 0);
- free_irq(kp->key_stuck_irq, kp);
- free_irq(kp->key_sense_irq, kp);
- input_unregister_device(kp->input);
- kfree(kp);
-
- return 0;
}
#ifdef CONFIG_PM_SLEEP
@@ -713,7 +687,6 @@ static SIMPLE_DEV_PM_OPS(pm8xxx_kp_pm_ops,
static struct platform_driver pmic8xxx_kp_driver = {
.probe = pmic8xxx_kp_probe,
- .remove = pmic8xxx_kp_remove,
.driver = {
.name = PM8XXX_KEYPAD_DEV_NAME,
.owner = THIS_MODULE,
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v4 3/9] Input: pmic8xxx-keypad - Migrate to regmap APIs
2014-02-28 1:55 ` Stephen Boyd
@ 2014-02-28 1:55 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input
Use the regmap APIs for this driver instead of custom pm8xxx
APIs. This breaks this driver's dependency on the pm8xxx APIs and
allows us to easily port it to other bus protocols in the future.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/keyboard/pmic8xxx-keypad.c | 81 ++++++++++++--------------------
1 file changed, 29 insertions(+), 52 deletions(-)
diff --git a/drivers/input/keyboard/pmic8xxx-keypad.c b/drivers/input/keyboard/pmic8xxx-keypad.c
index bec53ebde7b2..0efd11e16b7e 100644
--- a/drivers/input/keyboard/pmic8xxx-keypad.c
+++ b/drivers/input/keyboard/pmic8xxx-keypad.c
@@ -19,8 +19,8 @@
#include <linux/bitops.h>
#include <linux/delay.h>
#include <linux/mutex.h>
+#include <linux/regmap.h>
-#include <linux/mfd/pm8xxx/core.h>
#include <linux/input/pmic8xxx-keypad.h>
#define PM8XXX_MAX_ROWS 18
@@ -86,6 +86,7 @@
* struct pmic8xxx_kp - internal keypad data structure
* @pdata - keypad platform data pointer
* @input - input device pointer for keypad
+ * @regmap - regmap handle
* @key_sense_irq - key press/release irq number
* @key_stuck_irq - key stuck notification irq number
* @keycodes - array to hold the key codes
@@ -97,6 +98,7 @@
struct pmic8xxx_kp {
const struct pm8xxx_keypad_platform_data *pdata;
struct input_dev *input;
+ struct regmap *regmap;
int key_sense_irq;
int key_stuck_irq;
@@ -109,33 +111,6 @@ struct pmic8xxx_kp {
u8 ctrl_reg;
};
-static int pmic8xxx_kp_write_u8(struct pmic8xxx_kp *kp,
- u8 data, u16 reg)
-{
- int rc;
-
- rc = pm8xxx_writeb(kp->dev->parent, reg, data);
- return rc;
-}
-
-static int pmic8xxx_kp_read(struct pmic8xxx_kp *kp,
- u8 *data, u16 reg, unsigned num_bytes)
-{
- int rc;
-
- rc = pm8xxx_read_buf(kp->dev->parent, reg, data, num_bytes);
- return rc;
-}
-
-static int pmic8xxx_kp_read_u8(struct pmic8xxx_kp *kp,
- u8 *data, u16 reg)
-{
- int rc;
-
- rc = pmic8xxx_kp_read(kp, data, reg, 1);
- return rc;
-}
-
static u8 pmic8xxx_col_state(struct pmic8xxx_kp *kp, u8 col)
{
/* all keys pressed on that particular row? */
@@ -160,9 +135,9 @@ static u8 pmic8xxx_col_state(struct pmic8xxx_kp *kp, u8 col)
static int pmic8xxx_chk_sync_read(struct pmic8xxx_kp *kp)
{
int rc;
- u8 scan_val;
+ unsigned int scan_val;
- rc = pmic8xxx_kp_read_u8(kp, &scan_val, KEYP_SCAN);
+ rc = regmap_read(kp->regmap, KEYP_SCAN, &scan_val);
if (rc < 0) {
dev_err(kp->dev, "Error reading KEYP_SCAN reg, rc=%d\n", rc);
return rc;
@@ -170,7 +145,7 @@ static int pmic8xxx_chk_sync_read(struct pmic8xxx_kp *kp)
scan_val |= 0x1;
- rc = pmic8xxx_kp_write_u8(kp, scan_val, KEYP_SCAN);
+ rc = regmap_write(kp->regmap, KEYP_SCAN, scan_val);
if (rc < 0) {
dev_err(kp->dev, "Error writing KEYP_SCAN reg, rc=%d\n", rc);
return rc;
@@ -186,26 +161,24 @@ static int pmic8xxx_kp_read_data(struct pmic8xxx_kp *kp, u16 *state,
u16 data_reg, int read_rows)
{
int rc, row;
- u8 new_data[PM8XXX_MAX_ROWS];
+ unsigned int val;
- rc = pmic8xxx_kp_read(kp, new_data, data_reg, read_rows);
- if (rc)
- return rc;
-
- for (row = 0; row < kp->pdata->num_rows; row++) {
- dev_dbg(kp->dev, "new_data[%d] = %d\n", row,
- new_data[row]);
- state[row] = pmic8xxx_col_state(kp, new_data[row]);
+ for (row = 0; row < read_rows; row++) {
+ rc = regmap_read(kp->regmap, data_reg, &val);
+ if (rc)
+ return rc;
+ dev_dbg(kp->dev, "%d = %d\n", row, val);
+ state[row] = pmic8xxx_col_state(kp, val);
}
- return rc;
+ return 0;
}
static int pmic8xxx_kp_read_matrix(struct pmic8xxx_kp *kp, u16 *new_state,
u16 *old_state)
{
int rc, read_rows;
- u8 scan_val;
+ unsigned int scan_val;
if (kp->pdata->num_rows < PM8XXX_MIN_ROWS)
read_rows = PM8XXX_MIN_ROWS;
@@ -235,14 +208,14 @@ static int pmic8xxx_kp_read_matrix(struct pmic8xxx_kp *kp, u16 *new_state,
/* 4 * 32KHz clocks */
udelay((4 * DIV_ROUND_UP(USEC_PER_SEC, KEYP_CLOCK_FREQ)) + 1);
- rc = pmic8xxx_kp_read_u8(kp, &scan_val, KEYP_SCAN);
+ rc = regmap_read(kp->regmap, KEYP_SCAN, &scan_val);
if (rc < 0) {
dev_err(kp->dev, "Error reading KEYP_SCAN reg, rc=%d\n", rc);
return rc;
}
scan_val &= 0xFE;
- rc = pmic8xxx_kp_write_u8(kp, scan_val, KEYP_SCAN);
+ rc = regmap_write(kp->regmap, KEYP_SCAN, scan_val);
if (rc < 0)
dev_err(kp->dev, "Error writing KEYP_SCAN reg, rc=%d\n", rc);
@@ -378,10 +351,10 @@ static irqreturn_t pmic8xxx_kp_stuck_irq(int irq, void *data)
static irqreturn_t pmic8xxx_kp_irq(int irq, void *data)
{
struct pmic8xxx_kp *kp = data;
- u8 ctrl_val, events;
+ unsigned int ctrl_val, events;
int rc;
- rc = pmic8xxx_kp_read(kp, &ctrl_val, KEYP_CTRL, 1);
+ rc = regmap_read(kp->regmap, KEYP_CTRL, &ctrl_val);
if (rc < 0) {
dev_err(kp->dev, "failed to read keyp_ctrl register\n");
return IRQ_HANDLED;
@@ -420,7 +393,7 @@ static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
ctrl_val |= (bits << KEYP_CTRL_SCAN_ROWS_SHIFT);
- rc = pmic8xxx_kp_write_u8(kp, ctrl_val, KEYP_CTRL);
+ rc = regmap_write(kp->regmap, KEYP_CTRL, ctrl_val);
if (rc < 0) {
dev_err(kp->dev, "Error writing KEYP_CTRL reg, rc=%d\n", rc);
return rc;
@@ -438,7 +411,7 @@ static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
scan_val |= (cycles << KEYP_SCAN_ROW_HOLD_SHIFT);
- rc = pmic8xxx_kp_write_u8(kp, scan_val, KEYP_SCAN);
+ rc = regmap_write(kp->regmap, KEYP_SCAN, scan_val);
if (rc)
dev_err(kp->dev, "Error writing KEYP_SCAN reg, rc=%d\n", rc);
@@ -452,7 +425,7 @@ static int pmic8xxx_kp_enable(struct pmic8xxx_kp *kp)
kp->ctrl_reg |= KEYP_CTRL_KEYP_EN;
- rc = pmic8xxx_kp_write_u8(kp, kp->ctrl_reg, KEYP_CTRL);
+ rc = regmap_write(kp->regmap, KEYP_CTRL, kp->ctrl_reg);
if (rc < 0)
dev_err(kp->dev, "Error writing KEYP_CTRL reg, rc=%d\n", rc);
@@ -465,7 +438,7 @@ static int pmic8xxx_kp_disable(struct pmic8xxx_kp *kp)
kp->ctrl_reg &= ~KEYP_CTRL_KEYP_EN;
- rc = pmic8xxx_kp_write_u8(kp, kp->ctrl_reg, KEYP_CTRL);
+ rc = regmap_write(kp->regmap, KEYP_CTRL, kp->ctrl_reg);
if (rc < 0)
return rc;
@@ -503,7 +476,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
const struct matrix_keymap_data *keymap_data;
struct pmic8xxx_kp *kp;
int rc;
- u8 ctrl_val;
+ unsigned int ctrl_val;
if (!pdata || !pdata->num_cols || !pdata->num_rows ||
pdata->num_cols > PM8XXX_MAX_COLS ||
@@ -547,6 +520,10 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
if (!kp)
return -ENOMEM;
+ kp->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!kp->regmap)
+ return -ENODEV;
+
platform_set_drvdata(pdev, kp);
kp->pdata = pdata;
@@ -621,7 +598,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
return rc;
}
- rc = pmic8xxx_kp_read_u8(kp, &ctrl_val, KEYP_CTRL);
+ rc = regmap_read(kp->regmap, KEYP_CTRL, &ctrl_val);
if (rc < 0) {
dev_err(&pdev->dev, "failed to read KEYP_CTRL register\n");
return rc;
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 3/9] Input: pmic8xxx-keypad - Migrate to regmap APIs
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: linux-arm-kernel
Use the regmap APIs for this driver instead of custom pm8xxx
APIs. This breaks this driver's dependency on the pm8xxx APIs and
allows us to easily port it to other bus protocols in the future.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/keyboard/pmic8xxx-keypad.c | 81 ++++++++++++--------------------
1 file changed, 29 insertions(+), 52 deletions(-)
diff --git a/drivers/input/keyboard/pmic8xxx-keypad.c b/drivers/input/keyboard/pmic8xxx-keypad.c
index bec53ebde7b2..0efd11e16b7e 100644
--- a/drivers/input/keyboard/pmic8xxx-keypad.c
+++ b/drivers/input/keyboard/pmic8xxx-keypad.c
@@ -19,8 +19,8 @@
#include <linux/bitops.h>
#include <linux/delay.h>
#include <linux/mutex.h>
+#include <linux/regmap.h>
-#include <linux/mfd/pm8xxx/core.h>
#include <linux/input/pmic8xxx-keypad.h>
#define PM8XXX_MAX_ROWS 18
@@ -86,6 +86,7 @@
* struct pmic8xxx_kp - internal keypad data structure
* @pdata - keypad platform data pointer
* @input - input device pointer for keypad
+ * @regmap - regmap handle
* @key_sense_irq - key press/release irq number
* @key_stuck_irq - key stuck notification irq number
* @keycodes - array to hold the key codes
@@ -97,6 +98,7 @@
struct pmic8xxx_kp {
const struct pm8xxx_keypad_platform_data *pdata;
struct input_dev *input;
+ struct regmap *regmap;
int key_sense_irq;
int key_stuck_irq;
@@ -109,33 +111,6 @@ struct pmic8xxx_kp {
u8 ctrl_reg;
};
-static int pmic8xxx_kp_write_u8(struct pmic8xxx_kp *kp,
- u8 data, u16 reg)
-{
- int rc;
-
- rc = pm8xxx_writeb(kp->dev->parent, reg, data);
- return rc;
-}
-
-static int pmic8xxx_kp_read(struct pmic8xxx_kp *kp,
- u8 *data, u16 reg, unsigned num_bytes)
-{
- int rc;
-
- rc = pm8xxx_read_buf(kp->dev->parent, reg, data, num_bytes);
- return rc;
-}
-
-static int pmic8xxx_kp_read_u8(struct pmic8xxx_kp *kp,
- u8 *data, u16 reg)
-{
- int rc;
-
- rc = pmic8xxx_kp_read(kp, data, reg, 1);
- return rc;
-}
-
static u8 pmic8xxx_col_state(struct pmic8xxx_kp *kp, u8 col)
{
/* all keys pressed on that particular row? */
@@ -160,9 +135,9 @@ static u8 pmic8xxx_col_state(struct pmic8xxx_kp *kp, u8 col)
static int pmic8xxx_chk_sync_read(struct pmic8xxx_kp *kp)
{
int rc;
- u8 scan_val;
+ unsigned int scan_val;
- rc = pmic8xxx_kp_read_u8(kp, &scan_val, KEYP_SCAN);
+ rc = regmap_read(kp->regmap, KEYP_SCAN, &scan_val);
if (rc < 0) {
dev_err(kp->dev, "Error reading KEYP_SCAN reg, rc=%d\n", rc);
return rc;
@@ -170,7 +145,7 @@ static int pmic8xxx_chk_sync_read(struct pmic8xxx_kp *kp)
scan_val |= 0x1;
- rc = pmic8xxx_kp_write_u8(kp, scan_val, KEYP_SCAN);
+ rc = regmap_write(kp->regmap, KEYP_SCAN, scan_val);
if (rc < 0) {
dev_err(kp->dev, "Error writing KEYP_SCAN reg, rc=%d\n", rc);
return rc;
@@ -186,26 +161,24 @@ static int pmic8xxx_kp_read_data(struct pmic8xxx_kp *kp, u16 *state,
u16 data_reg, int read_rows)
{
int rc, row;
- u8 new_data[PM8XXX_MAX_ROWS];
+ unsigned int val;
- rc = pmic8xxx_kp_read(kp, new_data, data_reg, read_rows);
- if (rc)
- return rc;
-
- for (row = 0; row < kp->pdata->num_rows; row++) {
- dev_dbg(kp->dev, "new_data[%d] = %d\n", row,
- new_data[row]);
- state[row] = pmic8xxx_col_state(kp, new_data[row]);
+ for (row = 0; row < read_rows; row++) {
+ rc = regmap_read(kp->regmap, data_reg, &val);
+ if (rc)
+ return rc;
+ dev_dbg(kp->dev, "%d = %d\n", row, val);
+ state[row] = pmic8xxx_col_state(kp, val);
}
- return rc;
+ return 0;
}
static int pmic8xxx_kp_read_matrix(struct pmic8xxx_kp *kp, u16 *new_state,
u16 *old_state)
{
int rc, read_rows;
- u8 scan_val;
+ unsigned int scan_val;
if (kp->pdata->num_rows < PM8XXX_MIN_ROWS)
read_rows = PM8XXX_MIN_ROWS;
@@ -235,14 +208,14 @@ static int pmic8xxx_kp_read_matrix(struct pmic8xxx_kp *kp, u16 *new_state,
/* 4 * 32KHz clocks */
udelay((4 * DIV_ROUND_UP(USEC_PER_SEC, KEYP_CLOCK_FREQ)) + 1);
- rc = pmic8xxx_kp_read_u8(kp, &scan_val, KEYP_SCAN);
+ rc = regmap_read(kp->regmap, KEYP_SCAN, &scan_val);
if (rc < 0) {
dev_err(kp->dev, "Error reading KEYP_SCAN reg, rc=%d\n", rc);
return rc;
}
scan_val &= 0xFE;
- rc = pmic8xxx_kp_write_u8(kp, scan_val, KEYP_SCAN);
+ rc = regmap_write(kp->regmap, KEYP_SCAN, scan_val);
if (rc < 0)
dev_err(kp->dev, "Error writing KEYP_SCAN reg, rc=%d\n", rc);
@@ -378,10 +351,10 @@ static irqreturn_t pmic8xxx_kp_stuck_irq(int irq, void *data)
static irqreturn_t pmic8xxx_kp_irq(int irq, void *data)
{
struct pmic8xxx_kp *kp = data;
- u8 ctrl_val, events;
+ unsigned int ctrl_val, events;
int rc;
- rc = pmic8xxx_kp_read(kp, &ctrl_val, KEYP_CTRL, 1);
+ rc = regmap_read(kp->regmap, KEYP_CTRL, &ctrl_val);
if (rc < 0) {
dev_err(kp->dev, "failed to read keyp_ctrl register\n");
return IRQ_HANDLED;
@@ -420,7 +393,7 @@ static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
ctrl_val |= (bits << KEYP_CTRL_SCAN_ROWS_SHIFT);
- rc = pmic8xxx_kp_write_u8(kp, ctrl_val, KEYP_CTRL);
+ rc = regmap_write(kp->regmap, KEYP_CTRL, ctrl_val);
if (rc < 0) {
dev_err(kp->dev, "Error writing KEYP_CTRL reg, rc=%d\n", rc);
return rc;
@@ -438,7 +411,7 @@ static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
scan_val |= (cycles << KEYP_SCAN_ROW_HOLD_SHIFT);
- rc = pmic8xxx_kp_write_u8(kp, scan_val, KEYP_SCAN);
+ rc = regmap_write(kp->regmap, KEYP_SCAN, scan_val);
if (rc)
dev_err(kp->dev, "Error writing KEYP_SCAN reg, rc=%d\n", rc);
@@ -452,7 +425,7 @@ static int pmic8xxx_kp_enable(struct pmic8xxx_kp *kp)
kp->ctrl_reg |= KEYP_CTRL_KEYP_EN;
- rc = pmic8xxx_kp_write_u8(kp, kp->ctrl_reg, KEYP_CTRL);
+ rc = regmap_write(kp->regmap, KEYP_CTRL, kp->ctrl_reg);
if (rc < 0)
dev_err(kp->dev, "Error writing KEYP_CTRL reg, rc=%d\n", rc);
@@ -465,7 +438,7 @@ static int pmic8xxx_kp_disable(struct pmic8xxx_kp *kp)
kp->ctrl_reg &= ~KEYP_CTRL_KEYP_EN;
- rc = pmic8xxx_kp_write_u8(kp, kp->ctrl_reg, KEYP_CTRL);
+ rc = regmap_write(kp->regmap, KEYP_CTRL, kp->ctrl_reg);
if (rc < 0)
return rc;
@@ -503,7 +476,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
const struct matrix_keymap_data *keymap_data;
struct pmic8xxx_kp *kp;
int rc;
- u8 ctrl_val;
+ unsigned int ctrl_val;
if (!pdata || !pdata->num_cols || !pdata->num_rows ||
pdata->num_cols > PM8XXX_MAX_COLS ||
@@ -547,6 +520,10 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
if (!kp)
return -ENOMEM;
+ kp->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!kp->regmap)
+ return -ENODEV;
+
platform_set_drvdata(pdev, kp);
kp->pdata = pdata;
@@ -621,7 +598,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
return rc;
}
- rc = pmic8xxx_kp_read_u8(kp, &ctrl_val, KEYP_CTRL);
+ rc = regmap_read(kp->regmap, KEYP_CTRL, &ctrl_val);
if (rc < 0) {
dev_err(&pdev->dev, "failed to read KEYP_CTRL register\n");
return rc;
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v4 4/9] Input: pmic8xxx-keypad - Migrate to DT
2014-02-28 1:55 ` Stephen Boyd
@ 2014-02-28 1:55 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/keyboard/pmic8xxx-keypad.c | 150 ++++++++++++++++++-------------
include/linux/input/pmic8xxx-keypad.h | 52 -----------
2 files changed, 86 insertions(+), 116 deletions(-)
delete mode 100644 include/linux/input/pmic8xxx-keypad.h
diff --git a/drivers/input/keyboard/pmic8xxx-keypad.c b/drivers/input/keyboard/pmic8xxx-keypad.c
index 0efd11e16b7e..f106d3235f6d 100644
--- a/drivers/input/keyboard/pmic8xxx-keypad.c
+++ b/drivers/input/keyboard/pmic8xxx-keypad.c
@@ -20,8 +20,8 @@
#include <linux/delay.h>
#include <linux/mutex.h>
#include <linux/regmap.h>
-
-#include <linux/input/pmic8xxx-keypad.h>
+#include <linux/of.h>
+#include <linux/input/matrix_keypad.h>
#define PM8XXX_MAX_ROWS 18
#define PM8XXX_MAX_COLS 8
@@ -84,7 +84,8 @@
/**
* struct pmic8xxx_kp - internal keypad data structure
- * @pdata - keypad platform data pointer
+ * @num_cols - number of columns of keypad
+ * @num_rows - number of row of keypad
* @input - input device pointer for keypad
* @regmap - regmap handle
* @key_sense_irq - key press/release irq number
@@ -96,7 +97,8 @@
* @ctrl_reg - control register value
*/
struct pmic8xxx_kp {
- const struct pm8xxx_keypad_platform_data *pdata;
+ unsigned int num_rows;
+ unsigned int num_cols;
struct input_dev *input;
struct regmap *regmap;
int key_sense_irq;
@@ -115,9 +117,9 @@ static u8 pmic8xxx_col_state(struct pmic8xxx_kp *kp, u8 col)
{
/* all keys pressed on that particular row? */
if (col == 0x00)
- return 1 << kp->pdata->num_cols;
+ return 1 << kp->num_cols;
else
- return col & ((1 << kp->pdata->num_cols) - 1);
+ return col & ((1 << kp->num_cols) - 1);
}
/*
@@ -180,10 +182,10 @@ static int pmic8xxx_kp_read_matrix(struct pmic8xxx_kp *kp, u16 *new_state,
int rc, read_rows;
unsigned int scan_val;
- if (kp->pdata->num_rows < PM8XXX_MIN_ROWS)
+ if (kp->num_rows < PM8XXX_MIN_ROWS)
read_rows = PM8XXX_MIN_ROWS;
else
- read_rows = kp->pdata->num_rows;
+ read_rows = kp->num_rows;
pmic8xxx_chk_sync_read(kp);
@@ -227,13 +229,13 @@ static void __pmic8xxx_kp_scan_matrix(struct pmic8xxx_kp *kp, u16 *new_state,
{
int row, col, code;
- for (row = 0; row < kp->pdata->num_rows; row++) {
+ for (row = 0; row < kp->num_rows; row++) {
int bits_changed = new_state[row] ^ old_state[row];
if (!bits_changed)
continue;
- for (col = 0; col < kp->pdata->num_cols; col++) {
+ for (col = 0; col < kp->num_cols; col++) {
if (!(bits_changed & (1 << col)))
continue;
@@ -259,9 +261,9 @@ static bool pmic8xxx_detect_ghost_keys(struct pmic8xxx_kp *kp, u16 *new_state)
u16 check, row_state;
check = 0;
- for (row = 0; row < kp->pdata->num_rows; row++) {
+ for (row = 0; row < kp->num_rows; row++) {
row_state = (~new_state[row]) &
- ((1 << kp->pdata->num_cols) - 1);
+ ((1 << kp->num_cols) - 1);
if (hweight16(row_state) > 1) {
if (found_first == -1)
@@ -369,8 +371,13 @@ static irqreturn_t pmic8xxx_kp_irq(int irq, void *data)
return IRQ_HANDLED;
}
-static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
+static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp,
+ struct platform_device *pdev)
{
+ const struct device_node *of_node = pdev->dev.of_node;
+ unsigned int scan_delay_ms;
+ unsigned int row_hold_ns;
+ unsigned int debounce_ms;
int bits, rc, cycles;
u8 scan_val = 0, ctrl_val = 0;
static const u8 row_bits[] = {
@@ -378,18 +385,18 @@ static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
};
/* Find column bits */
- if (kp->pdata->num_cols < KEYP_CTRL_SCAN_COLS_MIN)
+ if (kp->num_cols < KEYP_CTRL_SCAN_COLS_MIN)
bits = 0;
else
- bits = kp->pdata->num_cols - KEYP_CTRL_SCAN_COLS_MIN;
+ bits = kp->num_cols - KEYP_CTRL_SCAN_COLS_MIN;
ctrl_val = (bits & KEYP_CTRL_SCAN_COLS_BITS) <<
KEYP_CTRL_SCAN_COLS_SHIFT;
/* Find row bits */
- if (kp->pdata->num_rows < KEYP_CTRL_SCAN_ROWS_MIN)
+ if (kp->num_rows < KEYP_CTRL_SCAN_ROWS_MIN)
bits = 0;
else
- bits = row_bits[kp->pdata->num_rows - KEYP_CTRL_SCAN_ROWS_MIN];
+ bits = row_bits[kp->num_rows - KEYP_CTRL_SCAN_ROWS_MIN];
ctrl_val |= (bits << KEYP_CTRL_SCAN_ROWS_SHIFT);
@@ -399,15 +406,44 @@ static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
return rc;
}
- bits = (kp->pdata->debounce_ms / 5) - 1;
+ if (of_property_read_u32(of_node, "scan-delay", &scan_delay_ms))
+ scan_delay_ms = MIN_SCAN_DELAY;
+
+ if (scan_delay_ms > MAX_SCAN_DELAY || scan_delay_ms < MIN_SCAN_DELAY ||
+ !is_power_of_2(scan_delay_ms)) {
+ dev_err(&pdev->dev, "invalid keypad scan time supplied\n");
+ return -EINVAL;
+ }
+
+ if (of_property_read_u32(of_node, "row-hold", &row_hold_ns))
+ row_hold_ns = MIN_ROW_HOLD_DELAY;
+
+ if (row_hold_ns > MAX_ROW_HOLD_DELAY ||
+ row_hold_ns < MIN_ROW_HOLD_DELAY ||
+ ((row_hold_ns % MIN_ROW_HOLD_DELAY) != 0)) {
+ dev_err(&pdev->dev, "invalid keypad row hold time supplied\n");
+ return -EINVAL;
+ }
+
+ if (of_property_read_u32(of_node, "debounce", &debounce_ms))
+ debounce_ms = MIN_DEBOUNCE_TIME;
+
+ if (((debounce_ms % 5) != 0) ||
+ debounce_ms > MAX_DEBOUNCE_TIME ||
+ debounce_ms < MIN_DEBOUNCE_TIME) {
+ dev_err(&pdev->dev, "invalid debounce time supplied\n");
+ return -EINVAL;
+ }
+
+ bits = (debounce_ms / 5) - 1;
scan_val |= (bits << KEYP_SCAN_DBOUNCE_SHIFT);
- bits = fls(kp->pdata->scan_delay_ms) - 1;
+ bits = fls(scan_delay_ms) - 1;
scan_val |= (bits << KEYP_SCAN_PAUSE_SHIFT);
/* Row hold time is a multiple of 32KHz cycles. */
- cycles = (kp->pdata->row_hold_ns * KEYP_CLOCK_FREQ) / NSEC_PER_SEC;
+ cycles = (row_hold_ns * KEYP_CLOCK_FREQ) / NSEC_PER_SEC;
scan_val |= (cycles << KEYP_SCAN_ROW_HOLD_SHIFT);
@@ -459,6 +495,13 @@ static void pmic8xxx_kp_close(struct input_dev *dev)
pmic8xxx_kp_disable(kp);
}
+static const struct of_device_id pm8xxx_match_table[] = {
+ { .compatible = "qcom,pm8058-keypad" },
+ { .compatible = "qcom,pm8921-keypad" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, pm8xxx_match_table);
+
/*
* keypad controller should be initialized in the following sequence
* only, otherwise it might get into FSM stuck state.
@@ -471,50 +514,27 @@ static void pmic8xxx_kp_close(struct input_dev *dev)
*/
static int pmic8xxx_kp_probe(struct platform_device *pdev)
{
- const struct pm8xxx_keypad_platform_data *pdata =
- dev_get_platdata(&pdev->dev);
- const struct matrix_keymap_data *keymap_data;
+ unsigned int rows, cols;
+ bool repeat;
+ bool wakeup;
struct pmic8xxx_kp *kp;
int rc;
unsigned int ctrl_val;
- if (!pdata || !pdata->num_cols || !pdata->num_rows ||
- pdata->num_cols > PM8XXX_MAX_COLS ||
- pdata->num_rows > PM8XXX_MAX_ROWS ||
- pdata->num_cols < PM8XXX_MIN_COLS) {
- dev_err(&pdev->dev, "invalid platform data\n");
- return -EINVAL;
- }
-
- if (!pdata->scan_delay_ms ||
- pdata->scan_delay_ms > MAX_SCAN_DELAY ||
- pdata->scan_delay_ms < MIN_SCAN_DELAY ||
- !is_power_of_2(pdata->scan_delay_ms)) {
- dev_err(&pdev->dev, "invalid keypad scan time supplied\n");
- return -EINVAL;
- }
-
- if (!pdata->row_hold_ns ||
- pdata->row_hold_ns > MAX_ROW_HOLD_DELAY ||
- pdata->row_hold_ns < MIN_ROW_HOLD_DELAY ||
- ((pdata->row_hold_ns % MIN_ROW_HOLD_DELAY) != 0)) {
- dev_err(&pdev->dev, "invalid keypad row hold time supplied\n");
- return -EINVAL;
- }
+ rc = matrix_keypad_parse_of_params(&pdev->dev, &rows, &cols);
+ if (rc)
+ return rc;
- if (!pdata->debounce_ms ||
- ((pdata->debounce_ms % 5) != 0) ||
- pdata->debounce_ms > MAX_DEBOUNCE_TIME ||
- pdata->debounce_ms < MIN_DEBOUNCE_TIME) {
- dev_err(&pdev->dev, "invalid debounce time supplied\n");
+ if (cols > PM8XXX_MAX_COLS || rows > PM8XXX_MAX_ROWS ||
+ cols < PM8XXX_MIN_COLS) {
+ dev_err(&pdev->dev, "invalid platform data\n");
return -EINVAL;
}
- keymap_data = pdata->keymap_data;
- if (!keymap_data) {
- dev_err(&pdev->dev, "no keymap data supplied\n");
- return -EINVAL;
- }
+ repeat = !of_property_read_bool(pdev->dev.of_node,
+ "linux,input-no-autorepeat");
+ wakeup = !of_property_read_bool(pdev->dev.of_node,
+ "linux,keypad-wakeup");
kp = devm_kzalloc(&pdev->dev, sizeof(*kp), GFP_KERNEL);
if (!kp)
@@ -526,7 +546,8 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, kp);
- kp->pdata = pdata;
+ kp->num_rows = rows;
+ kp->num_cols = cols;
kp->dev = &pdev->dev;
kp->input = devm_input_allocate_device(&pdev->dev);
@@ -547,8 +568,8 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
return kp->key_stuck_irq;
}
- kp->input->name = pdata->input_name ? : "PMIC8XXX keypad";
- kp->input->phys = pdata->input_phys_device ? : "pmic8xxx_keypad/input0";
+ kp->input->name = "PMIC8XXX keypad";
+ kp->input->phys = "pmic8xxx_keypad/input0";
kp->input->id.bustype = BUS_I2C;
kp->input->id.version = 0x0001;
@@ -558,7 +579,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
kp->input->open = pmic8xxx_kp_open;
kp->input->close = pmic8xxx_kp_close;
- rc = matrix_keypad_build_keymap(keymap_data, NULL,
+ rc = matrix_keypad_build_keymap(NULL, NULL,
PM8XXX_MAX_ROWS, PM8XXX_MAX_COLS,
kp->keycodes, kp->input);
if (rc) {
@@ -566,7 +587,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
return rc;
}
- if (pdata->rep)
+ if (repeat)
__set_bit(EV_REP, kp->input->evbit);
input_set_capability(kp->input, EV_MSC, MSC_SCAN);
@@ -576,7 +597,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
memset(kp->keystate, 0xff, sizeof(kp->keystate));
memset(kp->stuckstate, 0xff, sizeof(kp->stuckstate));
- rc = pmic8xxx_kpd_init(kp);
+ rc = pmic8xxx_kpd_init(kp, pdev);
if (rc < 0) {
dev_err(&pdev->dev, "unable to initialize keypad controller\n");
return rc;
@@ -612,7 +633,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
return rc;
}
- device_init_wakeup(&pdev->dev, pdata->wakeup);
+ device_init_wakeup(&pdev->dev, wakeup);
return 0;
}
@@ -665,9 +686,10 @@ static SIMPLE_DEV_PM_OPS(pm8xxx_kp_pm_ops,
static struct platform_driver pmic8xxx_kp_driver = {
.probe = pmic8xxx_kp_probe,
.driver = {
- .name = PM8XXX_KEYPAD_DEV_NAME,
+ .name = "pm8xxx-keypad",
.owner = THIS_MODULE,
.pm = &pm8xxx_kp_pm_ops,
+ .of_match_table = pm8xxx_match_table,
},
};
module_platform_driver(pmic8xxx_kp_driver);
diff --git a/include/linux/input/pmic8xxx-keypad.h b/include/linux/input/pmic8xxx-keypad.h
deleted file mode 100644
index 5f1e2f9ad959..000000000000
--- a/include/linux/input/pmic8xxx-keypad.h
+++ /dev/null
@@ -1,52 +0,0 @@
-/* Copyright (c) 2011, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __PMIC8XXX_KEYPAD_H__
-#define __PMIC8XXX_KEYPAD_H__
-
-#include <linux/input/matrix_keypad.h>
-
-#define PM8XXX_KEYPAD_DEV_NAME "pm8xxx-keypad"
-
-/**
- * struct pm8xxx_keypad_platform_data - platform data for keypad
- * @keymap_data - matrix keymap data
- * @input_name - input device name
- * @input_phys_device - input device name
- * @num_cols - number of columns of keypad
- * @num_rows - number of row of keypad
- * @debounce_ms - debounce period in milliseconds
- * @scan_delay_ms - scan delay in milliseconds
- * @row_hold_ns - row hold period in nanoseconds
- * @wakeup - configure keypad as wakeup
- * @rep - enable or disable key repeat bit
- */
-struct pm8xxx_keypad_platform_data {
- const struct matrix_keymap_data *keymap_data;
-
- const char *input_name;
- const char *input_phys_device;
-
- unsigned int num_cols;
- unsigned int num_rows;
- unsigned int rows_gpio_start;
- unsigned int cols_gpio_start;
-
- unsigned int debounce_ms;
- unsigned int scan_delay_ms;
- unsigned int row_hold_ns;
-
- bool wakeup;
- bool rep;
-};
-
-#endif /*__PMIC8XXX_KEYPAD_H__ */
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 4/9] Input: pmic8xxx-keypad - Migrate to DT
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: linux-arm-kernel
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/keyboard/pmic8xxx-keypad.c | 150 ++++++++++++++++++-------------
include/linux/input/pmic8xxx-keypad.h | 52 -----------
2 files changed, 86 insertions(+), 116 deletions(-)
delete mode 100644 include/linux/input/pmic8xxx-keypad.h
diff --git a/drivers/input/keyboard/pmic8xxx-keypad.c b/drivers/input/keyboard/pmic8xxx-keypad.c
index 0efd11e16b7e..f106d3235f6d 100644
--- a/drivers/input/keyboard/pmic8xxx-keypad.c
+++ b/drivers/input/keyboard/pmic8xxx-keypad.c
@@ -20,8 +20,8 @@
#include <linux/delay.h>
#include <linux/mutex.h>
#include <linux/regmap.h>
-
-#include <linux/input/pmic8xxx-keypad.h>
+#include <linux/of.h>
+#include <linux/input/matrix_keypad.h>
#define PM8XXX_MAX_ROWS 18
#define PM8XXX_MAX_COLS 8
@@ -84,7 +84,8 @@
/**
* struct pmic8xxx_kp - internal keypad data structure
- * @pdata - keypad platform data pointer
+ * @num_cols - number of columns of keypad
+ * @num_rows - number of row of keypad
* @input - input device pointer for keypad
* @regmap - regmap handle
* @key_sense_irq - key press/release irq number
@@ -96,7 +97,8 @@
* @ctrl_reg - control register value
*/
struct pmic8xxx_kp {
- const struct pm8xxx_keypad_platform_data *pdata;
+ unsigned int num_rows;
+ unsigned int num_cols;
struct input_dev *input;
struct regmap *regmap;
int key_sense_irq;
@@ -115,9 +117,9 @@ static u8 pmic8xxx_col_state(struct pmic8xxx_kp *kp, u8 col)
{
/* all keys pressed on that particular row? */
if (col == 0x00)
- return 1 << kp->pdata->num_cols;
+ return 1 << kp->num_cols;
else
- return col & ((1 << kp->pdata->num_cols) - 1);
+ return col & ((1 << kp->num_cols) - 1);
}
/*
@@ -180,10 +182,10 @@ static int pmic8xxx_kp_read_matrix(struct pmic8xxx_kp *kp, u16 *new_state,
int rc, read_rows;
unsigned int scan_val;
- if (kp->pdata->num_rows < PM8XXX_MIN_ROWS)
+ if (kp->num_rows < PM8XXX_MIN_ROWS)
read_rows = PM8XXX_MIN_ROWS;
else
- read_rows = kp->pdata->num_rows;
+ read_rows = kp->num_rows;
pmic8xxx_chk_sync_read(kp);
@@ -227,13 +229,13 @@ static void __pmic8xxx_kp_scan_matrix(struct pmic8xxx_kp *kp, u16 *new_state,
{
int row, col, code;
- for (row = 0; row < kp->pdata->num_rows; row++) {
+ for (row = 0; row < kp->num_rows; row++) {
int bits_changed = new_state[row] ^ old_state[row];
if (!bits_changed)
continue;
- for (col = 0; col < kp->pdata->num_cols; col++) {
+ for (col = 0; col < kp->num_cols; col++) {
if (!(bits_changed & (1 << col)))
continue;
@@ -259,9 +261,9 @@ static bool pmic8xxx_detect_ghost_keys(struct pmic8xxx_kp *kp, u16 *new_state)
u16 check, row_state;
check = 0;
- for (row = 0; row < kp->pdata->num_rows; row++) {
+ for (row = 0; row < kp->num_rows; row++) {
row_state = (~new_state[row]) &
- ((1 << kp->pdata->num_cols) - 1);
+ ((1 << kp->num_cols) - 1);
if (hweight16(row_state) > 1) {
if (found_first == -1)
@@ -369,8 +371,13 @@ static irqreturn_t pmic8xxx_kp_irq(int irq, void *data)
return IRQ_HANDLED;
}
-static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
+static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp,
+ struct platform_device *pdev)
{
+ const struct device_node *of_node = pdev->dev.of_node;
+ unsigned int scan_delay_ms;
+ unsigned int row_hold_ns;
+ unsigned int debounce_ms;
int bits, rc, cycles;
u8 scan_val = 0, ctrl_val = 0;
static const u8 row_bits[] = {
@@ -378,18 +385,18 @@ static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
};
/* Find column bits */
- if (kp->pdata->num_cols < KEYP_CTRL_SCAN_COLS_MIN)
+ if (kp->num_cols < KEYP_CTRL_SCAN_COLS_MIN)
bits = 0;
else
- bits = kp->pdata->num_cols - KEYP_CTRL_SCAN_COLS_MIN;
+ bits = kp->num_cols - KEYP_CTRL_SCAN_COLS_MIN;
ctrl_val = (bits & KEYP_CTRL_SCAN_COLS_BITS) <<
KEYP_CTRL_SCAN_COLS_SHIFT;
/* Find row bits */
- if (kp->pdata->num_rows < KEYP_CTRL_SCAN_ROWS_MIN)
+ if (kp->num_rows < KEYP_CTRL_SCAN_ROWS_MIN)
bits = 0;
else
- bits = row_bits[kp->pdata->num_rows - KEYP_CTRL_SCAN_ROWS_MIN];
+ bits = row_bits[kp->num_rows - KEYP_CTRL_SCAN_ROWS_MIN];
ctrl_val |= (bits << KEYP_CTRL_SCAN_ROWS_SHIFT);
@@ -399,15 +406,44 @@ static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
return rc;
}
- bits = (kp->pdata->debounce_ms / 5) - 1;
+ if (of_property_read_u32(of_node, "scan-delay", &scan_delay_ms))
+ scan_delay_ms = MIN_SCAN_DELAY;
+
+ if (scan_delay_ms > MAX_SCAN_DELAY || scan_delay_ms < MIN_SCAN_DELAY ||
+ !is_power_of_2(scan_delay_ms)) {
+ dev_err(&pdev->dev, "invalid keypad scan time supplied\n");
+ return -EINVAL;
+ }
+
+ if (of_property_read_u32(of_node, "row-hold", &row_hold_ns))
+ row_hold_ns = MIN_ROW_HOLD_DELAY;
+
+ if (row_hold_ns > MAX_ROW_HOLD_DELAY ||
+ row_hold_ns < MIN_ROW_HOLD_DELAY ||
+ ((row_hold_ns % MIN_ROW_HOLD_DELAY) != 0)) {
+ dev_err(&pdev->dev, "invalid keypad row hold time supplied\n");
+ return -EINVAL;
+ }
+
+ if (of_property_read_u32(of_node, "debounce", &debounce_ms))
+ debounce_ms = MIN_DEBOUNCE_TIME;
+
+ if (((debounce_ms % 5) != 0) ||
+ debounce_ms > MAX_DEBOUNCE_TIME ||
+ debounce_ms < MIN_DEBOUNCE_TIME) {
+ dev_err(&pdev->dev, "invalid debounce time supplied\n");
+ return -EINVAL;
+ }
+
+ bits = (debounce_ms / 5) - 1;
scan_val |= (bits << KEYP_SCAN_DBOUNCE_SHIFT);
- bits = fls(kp->pdata->scan_delay_ms) - 1;
+ bits = fls(scan_delay_ms) - 1;
scan_val |= (bits << KEYP_SCAN_PAUSE_SHIFT);
/* Row hold time is a multiple of 32KHz cycles. */
- cycles = (kp->pdata->row_hold_ns * KEYP_CLOCK_FREQ) / NSEC_PER_SEC;
+ cycles = (row_hold_ns * KEYP_CLOCK_FREQ) / NSEC_PER_SEC;
scan_val |= (cycles << KEYP_SCAN_ROW_HOLD_SHIFT);
@@ -459,6 +495,13 @@ static void pmic8xxx_kp_close(struct input_dev *dev)
pmic8xxx_kp_disable(kp);
}
+static const struct of_device_id pm8xxx_match_table[] = {
+ { .compatible = "qcom,pm8058-keypad" },
+ { .compatible = "qcom,pm8921-keypad" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, pm8xxx_match_table);
+
/*
* keypad controller should be initialized in the following sequence
* only, otherwise it might get into FSM stuck state.
@@ -471,50 +514,27 @@ static void pmic8xxx_kp_close(struct input_dev *dev)
*/
static int pmic8xxx_kp_probe(struct platform_device *pdev)
{
- const struct pm8xxx_keypad_platform_data *pdata =
- dev_get_platdata(&pdev->dev);
- const struct matrix_keymap_data *keymap_data;
+ unsigned int rows, cols;
+ bool repeat;
+ bool wakeup;
struct pmic8xxx_kp *kp;
int rc;
unsigned int ctrl_val;
- if (!pdata || !pdata->num_cols || !pdata->num_rows ||
- pdata->num_cols > PM8XXX_MAX_COLS ||
- pdata->num_rows > PM8XXX_MAX_ROWS ||
- pdata->num_cols < PM8XXX_MIN_COLS) {
- dev_err(&pdev->dev, "invalid platform data\n");
- return -EINVAL;
- }
-
- if (!pdata->scan_delay_ms ||
- pdata->scan_delay_ms > MAX_SCAN_DELAY ||
- pdata->scan_delay_ms < MIN_SCAN_DELAY ||
- !is_power_of_2(pdata->scan_delay_ms)) {
- dev_err(&pdev->dev, "invalid keypad scan time supplied\n");
- return -EINVAL;
- }
-
- if (!pdata->row_hold_ns ||
- pdata->row_hold_ns > MAX_ROW_HOLD_DELAY ||
- pdata->row_hold_ns < MIN_ROW_HOLD_DELAY ||
- ((pdata->row_hold_ns % MIN_ROW_HOLD_DELAY) != 0)) {
- dev_err(&pdev->dev, "invalid keypad row hold time supplied\n");
- return -EINVAL;
- }
+ rc = matrix_keypad_parse_of_params(&pdev->dev, &rows, &cols);
+ if (rc)
+ return rc;
- if (!pdata->debounce_ms ||
- ((pdata->debounce_ms % 5) != 0) ||
- pdata->debounce_ms > MAX_DEBOUNCE_TIME ||
- pdata->debounce_ms < MIN_DEBOUNCE_TIME) {
- dev_err(&pdev->dev, "invalid debounce time supplied\n");
+ if (cols > PM8XXX_MAX_COLS || rows > PM8XXX_MAX_ROWS ||
+ cols < PM8XXX_MIN_COLS) {
+ dev_err(&pdev->dev, "invalid platform data\n");
return -EINVAL;
}
- keymap_data = pdata->keymap_data;
- if (!keymap_data) {
- dev_err(&pdev->dev, "no keymap data supplied\n");
- return -EINVAL;
- }
+ repeat = !of_property_read_bool(pdev->dev.of_node,
+ "linux,input-no-autorepeat");
+ wakeup = !of_property_read_bool(pdev->dev.of_node,
+ "linux,keypad-wakeup");
kp = devm_kzalloc(&pdev->dev, sizeof(*kp), GFP_KERNEL);
if (!kp)
@@ -526,7 +546,8 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, kp);
- kp->pdata = pdata;
+ kp->num_rows = rows;
+ kp->num_cols = cols;
kp->dev = &pdev->dev;
kp->input = devm_input_allocate_device(&pdev->dev);
@@ -547,8 +568,8 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
return kp->key_stuck_irq;
}
- kp->input->name = pdata->input_name ? : "PMIC8XXX keypad";
- kp->input->phys = pdata->input_phys_device ? : "pmic8xxx_keypad/input0";
+ kp->input->name = "PMIC8XXX keypad";
+ kp->input->phys = "pmic8xxx_keypad/input0";
kp->input->id.bustype = BUS_I2C;
kp->input->id.version = 0x0001;
@@ -558,7 +579,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
kp->input->open = pmic8xxx_kp_open;
kp->input->close = pmic8xxx_kp_close;
- rc = matrix_keypad_build_keymap(keymap_data, NULL,
+ rc = matrix_keypad_build_keymap(NULL, NULL,
PM8XXX_MAX_ROWS, PM8XXX_MAX_COLS,
kp->keycodes, kp->input);
if (rc) {
@@ -566,7 +587,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
return rc;
}
- if (pdata->rep)
+ if (repeat)
__set_bit(EV_REP, kp->input->evbit);
input_set_capability(kp->input, EV_MSC, MSC_SCAN);
@@ -576,7 +597,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
memset(kp->keystate, 0xff, sizeof(kp->keystate));
memset(kp->stuckstate, 0xff, sizeof(kp->stuckstate));
- rc = pmic8xxx_kpd_init(kp);
+ rc = pmic8xxx_kpd_init(kp, pdev);
if (rc < 0) {
dev_err(&pdev->dev, "unable to initialize keypad controller\n");
return rc;
@@ -612,7 +633,7 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
return rc;
}
- device_init_wakeup(&pdev->dev, pdata->wakeup);
+ device_init_wakeup(&pdev->dev, wakeup);
return 0;
}
@@ -665,9 +686,10 @@ static SIMPLE_DEV_PM_OPS(pm8xxx_kp_pm_ops,
static struct platform_driver pmic8xxx_kp_driver = {
.probe = pmic8xxx_kp_probe,
.driver = {
- .name = PM8XXX_KEYPAD_DEV_NAME,
+ .name = "pm8xxx-keypad",
.owner = THIS_MODULE,
.pm = &pm8xxx_kp_pm_ops,
+ .of_match_table = pm8xxx_match_table,
},
};
module_platform_driver(pmic8xxx_kp_driver);
diff --git a/include/linux/input/pmic8xxx-keypad.h b/include/linux/input/pmic8xxx-keypad.h
deleted file mode 100644
index 5f1e2f9ad959..000000000000
--- a/include/linux/input/pmic8xxx-keypad.h
+++ /dev/null
@@ -1,52 +0,0 @@
-/* Copyright (c) 2011, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __PMIC8XXX_KEYPAD_H__
-#define __PMIC8XXX_KEYPAD_H__
-
-#include <linux/input/matrix_keypad.h>
-
-#define PM8XXX_KEYPAD_DEV_NAME "pm8xxx-keypad"
-
-/**
- * struct pm8xxx_keypad_platform_data - platform data for keypad
- * @keymap_data - matrix keymap data
- * @input_name - input device name
- * @input_phys_device - input device name
- * @num_cols - number of columns of keypad
- * @num_rows - number of row of keypad
- * @debounce_ms - debounce period in milliseconds
- * @scan_delay_ms - scan delay in milliseconds
- * @row_hold_ns - row hold period in nanoseconds
- * @wakeup - configure keypad as wakeup
- * @rep - enable or disable key repeat bit
- */
-struct pm8xxx_keypad_platform_data {
- const struct matrix_keymap_data *keymap_data;
-
- const char *input_name;
- const char *input_phys_device;
-
- unsigned int num_cols;
- unsigned int num_rows;
- unsigned int rows_gpio_start;
- unsigned int cols_gpio_start;
-
- unsigned int debounce_ms;
- unsigned int scan_delay_ms;
- unsigned int row_hold_ns;
-
- bool wakeup;
- bool rep;
-};
-
-#endif /*__PMIC8XXX_KEYPAD_H__ */
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* Re: [PATCH v4 4/9] Input: pmic8xxx-keypad - Migrate to DT
2014-02-28 1:55 ` Stephen Boyd
@ 2014-02-28 3:41 ` Josh Cartwright
-1 siblings, 0 replies; 39+ messages in thread
From: Josh Cartwright @ 2014-02-28 3:41 UTC (permalink / raw)
To: Stephen Boyd
Cc: Dmitry Torokhov, linux-kernel, linux-arm-msm, linux-arm-kernel,
linux-input
Looks good, with the exception of one thing...
On Thu, Feb 27, 2014 at 05:55:15PM -0800, Stephen Boyd wrote:
> The driver is only supported on DT enabled platforms. Convert the
> driver to DT so that it can probe properly.
>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
> drivers/input/keyboard/pmic8xxx-keypad.c | 150 ++++++++++++++++++-------------
> @@ -471,50 +514,27 @@ static void pmic8xxx_kp_close(struct input_dev *dev)
> */
> static int pmic8xxx_kp_probe(struct platform_device *pdev)
> {
[..]
> - keymap_data = pdata->keymap_data;
> - if (!keymap_data) {
> - dev_err(&pdev->dev, "no keymap data supplied\n");
> - return -EINVAL;
> - }
> + repeat = !of_property_read_bool(pdev->dev.of_node,
> + "linux,input-no-autorepeat");
> + wakeup = !of_property_read_bool(pdev->dev.of_node,
> + "linux,keypad-wakeup");
I don't think you mean to invert this.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread* [PATCH v4 4/9] Input: pmic8xxx-keypad - Migrate to DT
@ 2014-02-28 3:41 ` Josh Cartwright
0 siblings, 0 replies; 39+ messages in thread
From: Josh Cartwright @ 2014-02-28 3:41 UTC (permalink / raw)
To: linux-arm-kernel
Looks good, with the exception of one thing...
On Thu, Feb 27, 2014 at 05:55:15PM -0800, Stephen Boyd wrote:
> The driver is only supported on DT enabled platforms. Convert the
> driver to DT so that it can probe properly.
>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
> drivers/input/keyboard/pmic8xxx-keypad.c | 150 ++++++++++++++++++-------------
> @@ -471,50 +514,27 @@ static void pmic8xxx_kp_close(struct input_dev *dev)
> */
> static int pmic8xxx_kp_probe(struct platform_device *pdev)
> {
[..]
> - keymap_data = pdata->keymap_data;
> - if (!keymap_data) {
> - dev_err(&pdev->dev, "no keymap data supplied\n");
> - return -EINVAL;
> - }
> + repeat = !of_property_read_bool(pdev->dev.of_node,
> + "linux,input-no-autorepeat");
> + wakeup = !of_property_read_bool(pdev->dev.of_node,
> + "linux,keypad-wakeup");
I don't think you mean to invert this.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v4 4/9] Input: pmic8xxx-keypad - Migrate to DT
2014-02-28 3:41 ` Josh Cartwright
@ 2014-02-28 18:29 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 18:29 UTC (permalink / raw)
To: Josh Cartwright
Cc: Dmitry Torokhov, linux-kernel, linux-arm-msm, linux-arm-kernel,
linux-input
On 02/27, Josh Cartwright wrote:
> Looks good, with the exception of one thing...
>
> On Thu, Feb 27, 2014 at 05:55:15PM -0800, Stephen Boyd wrote:
> > The driver is only supported on DT enabled platforms. Convert the
> > driver to DT so that it can probe properly.
> >
> > Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> > ---
> > drivers/input/keyboard/pmic8xxx-keypad.c | 150 ++++++++++++++++++-------------
> > @@ -471,50 +514,27 @@ static void pmic8xxx_kp_close(struct input_dev *dev)
> > */
> > static int pmic8xxx_kp_probe(struct platform_device *pdev)
> > {
> [..]
> > - keymap_data = pdata->keymap_data;
> > - if (!keymap_data) {
> > - dev_err(&pdev->dev, "no keymap data supplied\n");
> > - return -EINVAL;
> > - }
> > + repeat = !of_property_read_bool(pdev->dev.of_node,
> > + "linux,input-no-autorepeat");
> > + wakeup = !of_property_read_bool(pdev->dev.of_node,
> > + "linux,keypad-wakeup");
>
> I don't think you mean to invert this.
>
Good catch. Thanks.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread* [PATCH v4 4/9] Input: pmic8xxx-keypad - Migrate to DT
@ 2014-02-28 18:29 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 18:29 UTC (permalink / raw)
To: linux-arm-kernel
On 02/27, Josh Cartwright wrote:
> Looks good, with the exception of one thing...
>
> On Thu, Feb 27, 2014 at 05:55:15PM -0800, Stephen Boyd wrote:
> > The driver is only supported on DT enabled platforms. Convert the
> > driver to DT so that it can probe properly.
> >
> > Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> > ---
> > drivers/input/keyboard/pmic8xxx-keypad.c | 150 ++++++++++++++++++-------------
> > @@ -471,50 +514,27 @@ static void pmic8xxx_kp_close(struct input_dev *dev)
> > */
> > static int pmic8xxx_kp_probe(struct platform_device *pdev)
> > {
> [..]
> > - keymap_data = pdata->keymap_data;
> > - if (!keymap_data) {
> > - dev_err(&pdev->dev, "no keymap data supplied\n");
> > - return -EINVAL;
> > - }
> > + repeat = !of_property_read_bool(pdev->dev.of_node,
> > + "linux,input-no-autorepeat");
> > + wakeup = !of_property_read_bool(pdev->dev.of_node,
> > + "linux,keypad-wakeup");
>
> I don't think you mean to invert this.
>
Good catch. Thanks.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v4 5/9] Input: pmic8xxx-pwrkey - Migrate to DT
2014-02-28 1:55 ` Stephen Boyd
@ 2014-02-28 1:55 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/misc/pmic8xxx-pwrkey.c | 33 ++++++++++++++++++++-------------
include/linux/input/pmic8xxx-pwrkey.h | 31 -------------------------------
2 files changed, 20 insertions(+), 44 deletions(-)
delete mode 100644 include/linux/input/pmic8xxx-pwrkey.h
diff --git a/drivers/input/misc/pmic8xxx-pwrkey.c b/drivers/input/misc/pmic8xxx-pwrkey.c
index 0e1a05f95858..99a3587ff49f 100644
--- a/drivers/input/misc/pmic8xxx-pwrkey.c
+++ b/drivers/input/misc/pmic8xxx-pwrkey.c
@@ -19,8 +19,7 @@
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/log2.h>
-
-#include <linux/input/pmic8xxx-pwrkey.h>
+#include <linux/of.h>
#define PON_CNTL_1 0x1C
#define PON_CNTL_PULL_UP BIT(7)
@@ -79,6 +78,13 @@ static int pmic8xxx_pwrkey_resume(struct device *dev)
static SIMPLE_DEV_PM_OPS(pm8xxx_pwr_key_pm_ops,
pmic8xxx_pwrkey_suspend, pmic8xxx_pwrkey_resume);
+static const struct of_device_id pm8xxx_pwr_key_id_table[] = {
+ { .compatible = "qcom,pm8058-pwrkey" },
+ { .compatible = "qcom,pm8921-pwrkey" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, pm8xxx_pwr_key_id_table);
+
static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
{
struct input_dev *pwr;
@@ -89,15 +95,15 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
unsigned int pon_cntl;
struct regmap *regmap;
struct pmic8xxx_pwrkey *pwrkey;
- const struct pm8xxx_pwrkey_platform_data *pdata =
- dev_get_platdata(&pdev->dev);
+ u32 kpd_delay;
+ bool pull_up;
- if (!pdata) {
- dev_err(&pdev->dev, "power key platform data not supplied\n");
- return -EINVAL;
- }
+ if (of_property_read_u32(pdev->dev.of_node, "debounce", &kpd_delay))
+ kpd_delay = 0;
+
+ pull_up = of_property_read_bool(pdev->dev.of_node, "pull-up");
- if (pdata->kpd_trigger_delay_us > 62500) {
+ if (kpd_delay > 62500) {
dev_err(&pdev->dev, "invalid power key trigger delay\n");
return -EINVAL;
}
@@ -125,7 +131,7 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
pwr->name = "pmic8xxx_pwrkey";
pwr->phys = "pmic8xxx_pwrkey/input0";
- delay = (pdata->kpd_trigger_delay_us << 10) / USEC_PER_SEC;
+ delay = (kpd_delay << 10) / USEC_PER_SEC;
delay = 1 + ilog2(delay);
err = regmap_read(regmap, PON_CNTL_1, &pon_cntl);
@@ -136,7 +142,7 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
pon_cntl &= ~PON_CNTL_TRIG_DELAY_MASK;
pon_cntl |= (delay & PON_CNTL_TRIG_DELAY_MASK);
- if (pdata->pull_up)
+ if (pull_up)
pon_cntl |= PON_CNTL_PULL_UP;
else
pon_cntl &= ~PON_CNTL_PULL_UP;
@@ -172,7 +178,7 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
}
platform_set_drvdata(pdev, pwrkey);
- device_init_wakeup(&pdev->dev, pdata->wakeup);
+ device_init_wakeup(&pdev->dev, 1);
return 0;
}
@@ -188,9 +194,10 @@ static struct platform_driver pmic8xxx_pwrkey_driver = {
.probe = pmic8xxx_pwrkey_probe,
.remove = pmic8xxx_pwrkey_remove,
.driver = {
- .name = PM8XXX_PWRKEY_DEV_NAME,
+ .name = "pm8xxx-pwrkey",
.owner = THIS_MODULE,
.pm = &pm8xxx_pwr_key_pm_ops,
+ .of_match_table = pm8xxx_pwr_key_id_table,
},
};
module_platform_driver(pmic8xxx_pwrkey_driver);
diff --git a/include/linux/input/pmic8xxx-pwrkey.h b/include/linux/input/pmic8xxx-pwrkey.h
deleted file mode 100644
index 6d2974e57109..000000000000
--- a/include/linux/input/pmic8xxx-pwrkey.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/* Copyright (c) 2010-2011, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __PMIC8XXX_PWRKEY_H__
-#define __PMIC8XXX_PWRKEY_H__
-
-#define PM8XXX_PWRKEY_DEV_NAME "pm8xxx-pwrkey"
-
-/**
- * struct pm8xxx_pwrkey_platform_data - platform data for pwrkey driver
- * @pull up: power on register control for pull up/down configuration
- * @kpd_trigger_delay_us: time delay for power key state change interrupt
- * trigger.
- * @wakeup: configure power key as wakeup source
- */
-struct pm8xxx_pwrkey_platform_data {
- bool pull_up;
- u32 kpd_trigger_delay_us;
- u32 wakeup;
-};
-
-#endif /* __PMIC8XXX_PWRKEY_H__ */
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 5/9] Input: pmic8xxx-pwrkey - Migrate to DT
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: linux-arm-kernel
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/misc/pmic8xxx-pwrkey.c | 33 ++++++++++++++++++++-------------
include/linux/input/pmic8xxx-pwrkey.h | 31 -------------------------------
2 files changed, 20 insertions(+), 44 deletions(-)
delete mode 100644 include/linux/input/pmic8xxx-pwrkey.h
diff --git a/drivers/input/misc/pmic8xxx-pwrkey.c b/drivers/input/misc/pmic8xxx-pwrkey.c
index 0e1a05f95858..99a3587ff49f 100644
--- a/drivers/input/misc/pmic8xxx-pwrkey.c
+++ b/drivers/input/misc/pmic8xxx-pwrkey.c
@@ -19,8 +19,7 @@
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/log2.h>
-
-#include <linux/input/pmic8xxx-pwrkey.h>
+#include <linux/of.h>
#define PON_CNTL_1 0x1C
#define PON_CNTL_PULL_UP BIT(7)
@@ -79,6 +78,13 @@ static int pmic8xxx_pwrkey_resume(struct device *dev)
static SIMPLE_DEV_PM_OPS(pm8xxx_pwr_key_pm_ops,
pmic8xxx_pwrkey_suspend, pmic8xxx_pwrkey_resume);
+static const struct of_device_id pm8xxx_pwr_key_id_table[] = {
+ { .compatible = "qcom,pm8058-pwrkey" },
+ { .compatible = "qcom,pm8921-pwrkey" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, pm8xxx_pwr_key_id_table);
+
static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
{
struct input_dev *pwr;
@@ -89,15 +95,15 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
unsigned int pon_cntl;
struct regmap *regmap;
struct pmic8xxx_pwrkey *pwrkey;
- const struct pm8xxx_pwrkey_platform_data *pdata =
- dev_get_platdata(&pdev->dev);
+ u32 kpd_delay;
+ bool pull_up;
- if (!pdata) {
- dev_err(&pdev->dev, "power key platform data not supplied\n");
- return -EINVAL;
- }
+ if (of_property_read_u32(pdev->dev.of_node, "debounce", &kpd_delay))
+ kpd_delay = 0;
+
+ pull_up = of_property_read_bool(pdev->dev.of_node, "pull-up");
- if (pdata->kpd_trigger_delay_us > 62500) {
+ if (kpd_delay > 62500) {
dev_err(&pdev->dev, "invalid power key trigger delay\n");
return -EINVAL;
}
@@ -125,7 +131,7 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
pwr->name = "pmic8xxx_pwrkey";
pwr->phys = "pmic8xxx_pwrkey/input0";
- delay = (pdata->kpd_trigger_delay_us << 10) / USEC_PER_SEC;
+ delay = (kpd_delay << 10) / USEC_PER_SEC;
delay = 1 + ilog2(delay);
err = regmap_read(regmap, PON_CNTL_1, &pon_cntl);
@@ -136,7 +142,7 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
pon_cntl &= ~PON_CNTL_TRIG_DELAY_MASK;
pon_cntl |= (delay & PON_CNTL_TRIG_DELAY_MASK);
- if (pdata->pull_up)
+ if (pull_up)
pon_cntl |= PON_CNTL_PULL_UP;
else
pon_cntl &= ~PON_CNTL_PULL_UP;
@@ -172,7 +178,7 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
}
platform_set_drvdata(pdev, pwrkey);
- device_init_wakeup(&pdev->dev, pdata->wakeup);
+ device_init_wakeup(&pdev->dev, 1);
return 0;
}
@@ -188,9 +194,10 @@ static struct platform_driver pmic8xxx_pwrkey_driver = {
.probe = pmic8xxx_pwrkey_probe,
.remove = pmic8xxx_pwrkey_remove,
.driver = {
- .name = PM8XXX_PWRKEY_DEV_NAME,
+ .name = "pm8xxx-pwrkey",
.owner = THIS_MODULE,
.pm = &pm8xxx_pwr_key_pm_ops,
+ .of_match_table = pm8xxx_pwr_key_id_table,
},
};
module_platform_driver(pmic8xxx_pwrkey_driver);
diff --git a/include/linux/input/pmic8xxx-pwrkey.h b/include/linux/input/pmic8xxx-pwrkey.h
deleted file mode 100644
index 6d2974e57109..000000000000
--- a/include/linux/input/pmic8xxx-pwrkey.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/* Copyright (c) 2010-2011, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __PMIC8XXX_PWRKEY_H__
-#define __PMIC8XXX_PWRKEY_H__
-
-#define PM8XXX_PWRKEY_DEV_NAME "pm8xxx-pwrkey"
-
-/**
- * struct pm8xxx_pwrkey_platform_data - platform data for pwrkey driver
- * @pull up: power on register control for pull up/down configuration
- * @kpd_trigger_delay_us: time delay for power key state change interrupt
- * trigger.
- * @wakeup: configure power key as wakeup source
- */
-struct pm8xxx_pwrkey_platform_data {
- bool pull_up;
- u32 kpd_trigger_delay_us;
- u32 wakeup;
-};
-
-#endif /* __PMIC8XXX_PWRKEY_H__ */
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* Re: [PATCH v4 5/9] Input: pmic8xxx-pwrkey - Migrate to DT
2014-02-28 1:55 ` Stephen Boyd
@ 2014-02-28 3:45 ` Josh Cartwright
-1 siblings, 0 replies; 39+ messages in thread
From: Josh Cartwright @ 2014-02-28 3:45 UTC (permalink / raw)
To: Stephen Boyd
Cc: Dmitry Torokhov, linux-kernel, linux-arm-msm, linux-arm-kernel,
linux-input
On Thu, Feb 27, 2014 at 05:55:16PM -0800, Stephen Boyd wrote:
> The driver is only supported on DT enabled platforms. Convert the
> driver to DT so that it can probe properly.
>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
> --- a/drivers/input/misc/pmic8xxx-pwrkey.c
> +++ b/drivers/input/misc/pmic8xxx-pwrkey.c
> @@ -172,7 +178,7 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
> }
>
> platform_set_drvdata(pdev, pwrkey);
> - device_init_wakeup(&pdev->dev, pdata->wakeup);
> + device_init_wakeup(&pdev->dev, 1);
Is there a particular reason you aren't providing a 'linux,wakeup'
property for pwrkey?
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v4 5/9] Input: pmic8xxx-pwrkey - Migrate to DT
@ 2014-02-28 3:45 ` Josh Cartwright
0 siblings, 0 replies; 39+ messages in thread
From: Josh Cartwright @ 2014-02-28 3:45 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Feb 27, 2014 at 05:55:16PM -0800, Stephen Boyd wrote:
> The driver is only supported on DT enabled platforms. Convert the
> driver to DT so that it can probe properly.
>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
> --- a/drivers/input/misc/pmic8xxx-pwrkey.c
> +++ b/drivers/input/misc/pmic8xxx-pwrkey.c
> @@ -172,7 +178,7 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
> }
>
> platform_set_drvdata(pdev, pwrkey);
> - device_init_wakeup(&pdev->dev, pdata->wakeup);
> + device_init_wakeup(&pdev->dev, 1);
Is there a particular reason you aren't providing a 'linux,wakeup'
property for pwrkey?
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v4 5/9] Input: pmic8xxx-pwrkey - Migrate to DT
2014-02-28 3:45 ` Josh Cartwright
@ 2014-02-28 18:32 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 18:32 UTC (permalink / raw)
To: Josh Cartwright
Cc: Dmitry Torokhov, linux-kernel, linux-arm-msm, linux-arm-kernel,
linux-input
On 02/27, Josh Cartwright wrote:
> On Thu, Feb 27, 2014 at 05:55:16PM -0800, Stephen Boyd wrote:
> > The driver is only supported on DT enabled platforms. Convert the
> > driver to DT so that it can probe properly.
> >
> > Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> > ---
> > --- a/drivers/input/misc/pmic8xxx-pwrkey.c
> > +++ b/drivers/input/misc/pmic8xxx-pwrkey.c
> > @@ -172,7 +178,7 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
> > }
> >
> > platform_set_drvdata(pdev, pwrkey);
> > - device_init_wakeup(&pdev->dev, pdata->wakeup);
> > + device_init_wakeup(&pdev->dev, 1);
>
> Is there a particular reason you aren't providing a 'linux,wakeup'
> property for pwrkey?
>
In all the users of this device I've never seen wakeup set to 0.
Given that this is a power key it makes sense because this is
used to wake up a phone from suspend (also see the comment above
device_init_wakeup() where power buttons are explicitly called
out).
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v4 5/9] Input: pmic8xxx-pwrkey - Migrate to DT
@ 2014-02-28 18:32 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 18:32 UTC (permalink / raw)
To: linux-arm-kernel
On 02/27, Josh Cartwright wrote:
> On Thu, Feb 27, 2014 at 05:55:16PM -0800, Stephen Boyd wrote:
> > The driver is only supported on DT enabled platforms. Convert the
> > driver to DT so that it can probe properly.
> >
> > Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> > ---
> > --- a/drivers/input/misc/pmic8xxx-pwrkey.c
> > +++ b/drivers/input/misc/pmic8xxx-pwrkey.c
> > @@ -172,7 +178,7 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
> > }
> >
> > platform_set_drvdata(pdev, pwrkey);
> > - device_init_wakeup(&pdev->dev, pdata->wakeup);
> > + device_init_wakeup(&pdev->dev, 1);
>
> Is there a particular reason you aren't providing a 'linux,wakeup'
> property for pwrkey?
>
In all the users of this device I've never seen wakeup set to 0.
Given that this is a power key it makes sense because this is
used to wake up a phone from suspend (also see the comment above
device_init_wakeup() where power buttons are explicitly called
out).
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v4 6/9] Input: pm8xxx-vibrator - Add DT match table
2014-02-28 1:55 ` Stephen Boyd
@ 2014-02-28 1:55 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/misc/pm8xxx-vibrator.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/drivers/input/misc/pm8xxx-vibrator.c b/drivers/input/misc/pm8xxx-vibrator.c
index b88b7cbf93e2..5079bc54c3aa 100644
--- a/drivers/input/misc/pm8xxx-vibrator.c
+++ b/drivers/input/misc/pm8xxx-vibrator.c
@@ -141,6 +141,13 @@ static int pm8xxx_vib_play_effect(struct input_dev *dev, void *data,
return 0;
}
+static const struct of_device_id pm8xxx_vib_id_table[] = {
+ { .compatible = "qcom,pm8058-vib" },
+ { .compatible = "qcom,pm8921-vib" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, pm8xxx_vib_id_table);
+
static int pm8xxx_vib_probe(struct platform_device *pdev)
{
@@ -220,6 +227,7 @@ static struct platform_driver pm8xxx_vib_driver = {
.name = "pm8xxx-vib",
.owner = THIS_MODULE,
.pm = &pm8xxx_vib_pm_ops,
+ .of_match_table = pm8xxx_vib_id_table,
},
};
module_platform_driver(pm8xxx_vib_driver);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 6/9] Input: pm8xxx-vibrator - Add DT match table
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: linux-arm-kernel
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/input/misc/pm8xxx-vibrator.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/drivers/input/misc/pm8xxx-vibrator.c b/drivers/input/misc/pm8xxx-vibrator.c
index b88b7cbf93e2..5079bc54c3aa 100644
--- a/drivers/input/misc/pm8xxx-vibrator.c
+++ b/drivers/input/misc/pm8xxx-vibrator.c
@@ -141,6 +141,13 @@ static int pm8xxx_vib_play_effect(struct input_dev *dev, void *data,
return 0;
}
+static const struct of_device_id pm8xxx_vib_id_table[] = {
+ { .compatible = "qcom,pm8058-vib" },
+ { .compatible = "qcom,pm8921-vib" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, pm8xxx_vib_id_table);
+
static int pm8xxx_vib_probe(struct platform_device *pdev)
{
@@ -220,6 +227,7 @@ static struct platform_driver pm8xxx_vib_driver = {
.name = "pm8xxx-vib",
.owner = THIS_MODULE,
.pm = &pm8xxx_vib_pm_ops,
+ .of_match_table = pm8xxx_vib_id_table,
},
};
module_platform_driver(pm8xxx_vib_driver);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v4 7/9] devicetree: bindings: Document PM8921/8058 keypads
2014-02-28 1:55 ` Stephen Boyd
(?)
@ 2014-02-28 1:55 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input, devicetree
Document the keypad device found on PM8921 and PM8058 PMICs.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
.../bindings/input/qcom,pm8xxx-keypad.txt | 72 ++++++++++++++++++++++
1 file changed, 72 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
new file mode 100644
index 000000000000..aa5a9c6cf512
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
@@ -0,0 +1,72 @@
+Qualcomm PM8xxx PMIC Keypad
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8058-keypad"
+ "qcom,pm8921-keypad"
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the first interrupt specifies the key sense interrupt
+ and the second interrupt specifies the key stuck interrupt.
+ The format of the specifier is defined by the binding
+ document describing the node's interrupt parent.
+
+- linux,keymap:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the linux keymap. More information can be found in
+ input/matrix-keymap.txt.
+
+- keypad,num-rows:
+ Usage: required
+ Value type: <u32>
+ Definition: number of rows in the keymap. More information can be found
+ in input/matrix-keymap.txt.
+
+- keypad,num-columns:
+ Usage: required
+ Value type: <u32>
+ Definition: number of columns in the keymap. More information can be
+ found in input/matrix-keymap.txt.
+
+- debounce:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in microseconds that key must be pressed or release
+ for key sense interrupt to trigger.
+
+- scan-delay:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in microseconds to pause between successive scans
+ of the matrix array.
+
+- row-hold:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in nanoseconds to pause between scans of each row in
+ the matrix array.
+
+EXAMPLE
+
+ keypad {
+ compatible = "qcom,pm8921-keypad";
+ interrupt-parent = <&pmicintc>;
+ interrupts = <74 1>, <75 1>;
+ linux,keymap = <
+ MATRIX_KEY(0, 0, KEY_VOLUMEUP)
+ MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
+ MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
+ MATRIX_KEY(0, 3, KEY_CAMERA)
+ >;
+ keypad,num-rows = <1>;
+ keypad,num-columns = <5>;
+ debounce = <15>;
+ scan-delay = <32>;
+ row-hold = <91500>;
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 7/9] devicetree: bindings: Document PM8921/8058 keypads
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: linux-arm-kernel
Document the keypad device found on PM8921 and PM8058 PMICs.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
.../bindings/input/qcom,pm8xxx-keypad.txt | 72 ++++++++++++++++++++++
1 file changed, 72 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
new file mode 100644
index 000000000000..aa5a9c6cf512
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
@@ -0,0 +1,72 @@
+Qualcomm PM8xxx PMIC Keypad
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8058-keypad"
+ "qcom,pm8921-keypad"
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the first interrupt specifies the key sense interrupt
+ and the second interrupt specifies the key stuck interrupt.
+ The format of the specifier is defined by the binding
+ document describing the node's interrupt parent.
+
+- linux,keymap:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the linux keymap. More information can be found in
+ input/matrix-keymap.txt.
+
+- keypad,num-rows:
+ Usage: required
+ Value type: <u32>
+ Definition: number of rows in the keymap. More information can be found
+ in input/matrix-keymap.txt.
+
+- keypad,num-columns:
+ Usage: required
+ Value type: <u32>
+ Definition: number of columns in the keymap. More information can be
+ found in input/matrix-keymap.txt.
+
+- debounce:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in microseconds that key must be pressed or release
+ for key sense interrupt to trigger.
+
+- scan-delay:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in microseconds to pause between successive scans
+ of the matrix array.
+
+- row-hold:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in nanoseconds to pause between scans of each row in
+ the matrix array.
+
+EXAMPLE
+
+ keypad {
+ compatible = "qcom,pm8921-keypad";
+ interrupt-parent = <&pmicintc>;
+ interrupts = <74 1>, <75 1>;
+ linux,keymap = <
+ MATRIX_KEY(0, 0, KEY_VOLUMEUP)
+ MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
+ MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
+ MATRIX_KEY(0, 3, KEY_CAMERA)
+ >;
+ keypad,num-rows = <1>;
+ keypad,num-columns = <5>;
+ debounce = <15>;
+ scan-delay = <32>;
+ row-hold = <91500>;
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 7/9] devicetree: bindings: Document PM8921/8058 keypads
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input, devicetree
Document the keypad device found on PM8921 and PM8058 PMICs.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
.../bindings/input/qcom,pm8xxx-keypad.txt | 72 ++++++++++++++++++++++
1 file changed, 72 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
new file mode 100644
index 000000000000..aa5a9c6cf512
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
@@ -0,0 +1,72 @@
+Qualcomm PM8xxx PMIC Keypad
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8058-keypad"
+ "qcom,pm8921-keypad"
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the first interrupt specifies the key sense interrupt
+ and the second interrupt specifies the key stuck interrupt.
+ The format of the specifier is defined by the binding
+ document describing the node's interrupt parent.
+
+- linux,keymap:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the linux keymap. More information can be found in
+ input/matrix-keymap.txt.
+
+- keypad,num-rows:
+ Usage: required
+ Value type: <u32>
+ Definition: number of rows in the keymap. More information can be found
+ in input/matrix-keymap.txt.
+
+- keypad,num-columns:
+ Usage: required
+ Value type: <u32>
+ Definition: number of columns in the keymap. More information can be
+ found in input/matrix-keymap.txt.
+
+- debounce:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in microseconds that key must be pressed or release
+ for key sense interrupt to trigger.
+
+- scan-delay:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in microseconds to pause between successive scans
+ of the matrix array.
+
+- row-hold:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in nanoseconds to pause between scans of each row in
+ the matrix array.
+
+EXAMPLE
+
+ keypad {
+ compatible = "qcom,pm8921-keypad";
+ interrupt-parent = <&pmicintc>;
+ interrupts = <74 1>, <75 1>;
+ linux,keymap = <
+ MATRIX_KEY(0, 0, KEY_VOLUMEUP)
+ MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
+ MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
+ MATRIX_KEY(0, 3, KEY_CAMERA)
+ >;
+ keypad,num-rows = <1>;
+ keypad,num-columns = <5>;
+ debounce = <15>;
+ scan-delay = <32>;
+ row-hold = <91500>;
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* Re: [PATCH v4 7/9] devicetree: bindings: Document PM8921/8058 keypads
2014-02-28 1:55 ` Stephen Boyd
@ 2014-02-28 13:55 ` Josh Cartwright
-1 siblings, 0 replies; 39+ messages in thread
From: Josh Cartwright @ 2014-02-28 13:55 UTC (permalink / raw)
To: Stephen Boyd
Cc: Dmitry Torokhov, linux-kernel, linux-arm-msm, linux-arm-kernel,
linux-input, devicetree
On Thu, Feb 27, 2014 at 05:55:18PM -0800, Stephen Boyd wrote:
> Document the keypad device found on PM8921 and PM8058 PMICs.
[..]
> +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
> @@ -0,0 +1,72 @@
> +Qualcomm PM8xxx PMIC Keypad
> +
> +PROPERTIES
> +
> +- compatible:
> + Usage: required
> + Value type: <string>
> + Definition: must be one of:
> + "qcom,pm8058-keypad"
> + "qcom,pm8921-keypad"
> +- interrupts:
> + Usage: required
> + Value type: <prop-encoded-array>
> + Definition: the first interrupt specifies the key sense interrupt
> + and the second interrupt specifies the key stuck interrupt.
> + The format of the specifier is defined by the binding
> + document describing the node's interrupt parent.
> +
> +- linux,keymap:
> + Usage: required
> + Value type: <prop-encoded-array>
> + Definition: the linux keymap. More information can be found in
> + input/matrix-keymap.txt.
> +
> +- keypad,num-rows:
> + Usage: required
> + Value type: <u32>
> + Definition: number of rows in the keymap. More information can be found
> + in input/matrix-keymap.txt.
> +
> +- keypad,num-columns:
> + Usage: required
> + Value type: <u32>
> + Definition: number of columns in the keymap. More information can be
> + found in input/matrix-keymap.txt.
> +
> +- debounce:
> + Usage: optional
> + Value type: <u32>
> + Definition: time in microseconds that key must be pressed or release
> + for key sense interrupt to trigger.
> +
> +- scan-delay:
> + Usage: optional
> + Value type: <u32>
> + Definition: time in microseconds to pause between successive scans
> + of the matrix array.
> +
> +- row-hold:
> + Usage: optional
> + Value type: <u32>
> + Definition: time in nanoseconds to pause between scans of each row in
> + the matrix array.
- linux,wakeup?
- linux,no-auto-repeat?
> +
> +EXAMPLE
> +
> + keypad {
> + compatible = "qcom,pm8921-keypad";
> + interrupt-parent = <&pmicintc>;
> + interrupts = <74 1>, <75 1>;
> + linux,keymap = <
> + MATRIX_KEY(0, 0, KEY_VOLUMEUP)
> + MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
> + MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
> + MATRIX_KEY(0, 3, KEY_CAMERA)
> + >;
> + keypad,num-rows = <1>;
> + keypad,num-columns = <5>;
> + debounce = <15>;
> + scan-delay = <32>;
> + row-hold = <91500>;
> + };
It odd to me that these newly created bindings don't have 'reg'
properties, even though the device clearly has a register region.
I suppose it makes sense from a "port over from platform data to DT"
perspective, as these drivers have just assumed the location of their
registers to be fixed; however I suspect things will need to be changed
if/when we hope to share these drivers with pm8841/pm8941 and beyond...
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread* [PATCH v4 7/9] devicetree: bindings: Document PM8921/8058 keypads
@ 2014-02-28 13:55 ` Josh Cartwright
0 siblings, 0 replies; 39+ messages in thread
From: Josh Cartwright @ 2014-02-28 13:55 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Feb 27, 2014 at 05:55:18PM -0800, Stephen Boyd wrote:
> Document the keypad device found on PM8921 and PM8058 PMICs.
[..]
> +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
> @@ -0,0 +1,72 @@
> +Qualcomm PM8xxx PMIC Keypad
> +
> +PROPERTIES
> +
> +- compatible:
> + Usage: required
> + Value type: <string>
> + Definition: must be one of:
> + "qcom,pm8058-keypad"
> + "qcom,pm8921-keypad"
> +- interrupts:
> + Usage: required
> + Value type: <prop-encoded-array>
> + Definition: the first interrupt specifies the key sense interrupt
> + and the second interrupt specifies the key stuck interrupt.
> + The format of the specifier is defined by the binding
> + document describing the node's interrupt parent.
> +
> +- linux,keymap:
> + Usage: required
> + Value type: <prop-encoded-array>
> + Definition: the linux keymap. More information can be found in
> + input/matrix-keymap.txt.
> +
> +- keypad,num-rows:
> + Usage: required
> + Value type: <u32>
> + Definition: number of rows in the keymap. More information can be found
> + in input/matrix-keymap.txt.
> +
> +- keypad,num-columns:
> + Usage: required
> + Value type: <u32>
> + Definition: number of columns in the keymap. More information can be
> + found in input/matrix-keymap.txt.
> +
> +- debounce:
> + Usage: optional
> + Value type: <u32>
> + Definition: time in microseconds that key must be pressed or release
> + for key sense interrupt to trigger.
> +
> +- scan-delay:
> + Usage: optional
> + Value type: <u32>
> + Definition: time in microseconds to pause between successive scans
> + of the matrix array.
> +
> +- row-hold:
> + Usage: optional
> + Value type: <u32>
> + Definition: time in nanoseconds to pause between scans of each row in
> + the matrix array.
- linux,wakeup?
- linux,no-auto-repeat?
> +
> +EXAMPLE
> +
> + keypad {
> + compatible = "qcom,pm8921-keypad";
> + interrupt-parent = <&pmicintc>;
> + interrupts = <74 1>, <75 1>;
> + linux,keymap = <
> + MATRIX_KEY(0, 0, KEY_VOLUMEUP)
> + MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
> + MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
> + MATRIX_KEY(0, 3, KEY_CAMERA)
> + >;
> + keypad,num-rows = <1>;
> + keypad,num-columns = <5>;
> + debounce = <15>;
> + scan-delay = <32>;
> + row-hold = <91500>;
> + };
It odd to me that these newly created bindings don't have 'reg'
properties, even though the device clearly has a register region.
I suppose it makes sense from a "port over from platform data to DT"
perspective, as these drivers have just assumed the location of their
registers to be fixed; however I suspect things will need to be changed
if/when we hope to share these drivers with pm8841/pm8941 and beyond...
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v4 7/9] devicetree: bindings: Document PM8921/8058 keypads
2014-02-28 13:55 ` Josh Cartwright
@ 2014-02-28 18:37 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 18:37 UTC (permalink / raw)
To: Josh Cartwright
Cc: Dmitry Torokhov, linux-kernel, linux-arm-msm, linux-arm-kernel,
linux-input, devicetree
On 02/28, Josh Cartwright wrote:
> On Thu, Feb 27, 2014 at 05:55:18PM -0800, Stephen Boyd wrote:
>
> - linux,wakeup?
> - linux,no-auto-repeat?
Added.
>
> > +
> > +EXAMPLE
> > +
> > + keypad {
> > + compatible = "qcom,pm8921-keypad";
> > + interrupt-parent = <&pmicintc>;
> > + interrupts = <74 1>, <75 1>;
> > + linux,keymap = <
> > + MATRIX_KEY(0, 0, KEY_VOLUMEUP)
> > + MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
> > + MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
> > + MATRIX_KEY(0, 3, KEY_CAMERA)
> > + >;
> > + keypad,num-rows = <1>;
> > + keypad,num-columns = <5>;
> > + debounce = <15>;
> > + scan-delay = <32>;
> > + row-hold = <91500>;
> > + };
>
> It odd to me that these newly created bindings don't have 'reg'
> properties, even though the device clearly has a register region.
>
> I suppose it makes sense from a "port over from platform data to DT"
> perspective, as these drivers have just assumed the location of their
> registers to be fixed; however I suspect things will need to be changed
> if/when we hope to share these drivers with pm8841/pm8941 and beyond...
>
Agreed. I would love it if the platform OF code would create
IORESOURCE_REG resources for any reg properties that aren't
translatable to CPU addresses. That way we don't have to pick out
the reg property from DT with special OF code (like you've done
in rtc-pm8xxx). I'll throw the reg property into the binding so
that in the future we can support the register moving around
(although at the moment the driver will ignore it).
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread* [PATCH v4 7/9] devicetree: bindings: Document PM8921/8058 keypads
@ 2014-02-28 18:37 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 18:37 UTC (permalink / raw)
To: linux-arm-kernel
On 02/28, Josh Cartwright wrote:
> On Thu, Feb 27, 2014 at 05:55:18PM -0800, Stephen Boyd wrote:
>
> - linux,wakeup?
> - linux,no-auto-repeat?
Added.
>
> > +
> > +EXAMPLE
> > +
> > + keypad {
> > + compatible = "qcom,pm8921-keypad";
> > + interrupt-parent = <&pmicintc>;
> > + interrupts = <74 1>, <75 1>;
> > + linux,keymap = <
> > + MATRIX_KEY(0, 0, KEY_VOLUMEUP)
> > + MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
> > + MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
> > + MATRIX_KEY(0, 3, KEY_CAMERA)
> > + >;
> > + keypad,num-rows = <1>;
> > + keypad,num-columns = <5>;
> > + debounce = <15>;
> > + scan-delay = <32>;
> > + row-hold = <91500>;
> > + };
>
> It odd to me that these newly created bindings don't have 'reg'
> properties, even though the device clearly has a register region.
>
> I suppose it makes sense from a "port over from platform data to DT"
> perspective, as these drivers have just assumed the location of their
> registers to be fixed; however I suspect things will need to be changed
> if/when we hope to share these drivers with pm8841/pm8941 and beyond...
>
Agreed. I would love it if the platform OF code would create
IORESOURCE_REG resources for any reg properties that aren't
translatable to CPU addresses. That way we don't have to pick out
the reg property from DT with special OF code (like you've done
in rtc-pm8xxx). I'll throw the reg property into the binding so
that in the future we can support the register moving around
(although at the moment the driver will ignore it).
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v4 7/9] devicetree: bindings: Document PM8921/8058 keypads
2014-02-28 18:37 ` Stephen Boyd
@ 2014-02-28 19:11 ` Josh Cartwright
-1 siblings, 0 replies; 39+ messages in thread
From: Josh Cartwright @ 2014-02-28 19:11 UTC (permalink / raw)
To: Stephen Boyd
Cc: Josh Cartwright, Dmitry Torokhov, linux-kernel, linux-arm-msm,
linux-arm-kernel, linux-input, devicetree
On Fri, Feb 28, 2014 at 10:37:08AM -0800, Stephen Boyd wrote:
> On 02/28, Josh Cartwright wrote:
> > On Thu, Feb 27, 2014 at 05:55:18PM -0800, Stephen Boyd wrote:
> > > +
> > > +EXAMPLE
> > > +
> > > + keypad {
> > > + compatible = "qcom,pm8921-keypad";
> > > + interrupt-parent = <&pmicintc>;
> > > + interrupts = <74 1>, <75 1>;
> > > + linux,keymap = <
> > > + MATRIX_KEY(0, 0, KEY_VOLUMEUP)
> > > + MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
> > > + MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
> > > + MATRIX_KEY(0, 3, KEY_CAMERA)
> > > + >;
> > > + keypad,num-rows = <1>;
> > > + keypad,num-columns = <5>;
> > > + debounce = <15>;
> > > + scan-delay = <32>;
> > > + row-hold = <91500>;
> > > + };
> >
> > It odd to me that these newly created bindings don't have 'reg'
> > properties, even though the device clearly has a register region.
> >
> > I suppose it makes sense from a "port over from platform data to DT"
> > perspective, as these drivers have just assumed the location of their
> > registers to be fixed; however I suspect things will need to be changed
> > if/when we hope to share these drivers with pm8841/pm8941 and beyond...
> >
>
> Agreed. I would love it if the platform OF code would create
> IORESOURCE_REG resources for any reg properties that aren't
> translatable to CPU addresses. That way we don't have to pick out the
> reg property from DT with special OF code (like you've done in
> rtc-pm8xxx).
Yes, I agree this would be nice. The rtc-pm8xxx register parsing magic
is misplaced/ugly. I'll see about taking a crack at this and seeing
what it looks like.
> I'll throw the reg property into the binding so that in
> the future we can support the register moving around (although at the
> moment the driver will ignore it).
Great, I think this sounds good.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread* [PATCH v4 7/9] devicetree: bindings: Document PM8921/8058 keypads
@ 2014-02-28 19:11 ` Josh Cartwright
0 siblings, 0 replies; 39+ messages in thread
From: Josh Cartwright @ 2014-02-28 19:11 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Feb 28, 2014 at 10:37:08AM -0800, Stephen Boyd wrote:
> On 02/28, Josh Cartwright wrote:
> > On Thu, Feb 27, 2014 at 05:55:18PM -0800, Stephen Boyd wrote:
> > > +
> > > +EXAMPLE
> > > +
> > > + keypad {
> > > + compatible = "qcom,pm8921-keypad";
> > > + interrupt-parent = <&pmicintc>;
> > > + interrupts = <74 1>, <75 1>;
> > > + linux,keymap = <
> > > + MATRIX_KEY(0, 0, KEY_VOLUMEUP)
> > > + MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
> > > + MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
> > > + MATRIX_KEY(0, 3, KEY_CAMERA)
> > > + >;
> > > + keypad,num-rows = <1>;
> > > + keypad,num-columns = <5>;
> > > + debounce = <15>;
> > > + scan-delay = <32>;
> > > + row-hold = <91500>;
> > > + };
> >
> > It odd to me that these newly created bindings don't have 'reg'
> > properties, even though the device clearly has a register region.
> >
> > I suppose it makes sense from a "port over from platform data to DT"
> > perspective, as these drivers have just assumed the location of their
> > registers to be fixed; however I suspect things will need to be changed
> > if/when we hope to share these drivers with pm8841/pm8941 and beyond...
> >
>
> Agreed. I would love it if the platform OF code would create
> IORESOURCE_REG resources for any reg properties that aren't
> translatable to CPU addresses. That way we don't have to pick out the
> reg property from DT with special OF code (like you've done in
> rtc-pm8xxx).
Yes, I agree this would be nice. The rtc-pm8xxx register parsing magic
is misplaced/ugly. I'll see about taking a crack at this and seeing
what it looks like.
> I'll throw the reg property into the binding so that in
> the future we can support the register moving around (although at the
> moment the driver will ignore it).
Great, I think this sounds good.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v4 8/9] devicetree: bindings: Document PM8921/8058 power keys
2014-02-28 1:55 ` Stephen Boyd
(?)
@ 2014-02-28 1:55 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input, devicetree
Document the power key found on PM8921 and PM8058 PMICs.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
.../bindings/input/qcom,pm8xxx-pwrkey.txt | 39 ++++++++++++++++++++++
1 file changed, 39 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt
new file mode 100644
index 000000000000..e124d9f33632
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt
@@ -0,0 +1,39 @@
+Qualcomm PM8xxx PMIC Power Key
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8058-pwrkey"
+ "qcom,pm8921-pwrkey"
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the first interrupt specifies the key release interrupt
+ and the second interrupt specifies the key press interrupt.
+ The format of the specifier is defined by the binding
+ document describing the node's interrupt parent.
+
+- debounce:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in microseconds that key must be pressed or release
+ for state change interrupt to trigger.
+
+- pull-up:
+ Usage: optional
+ Value type: <empty>
+ Definition: presence of this property indicates that the KPDPWR_N pin
+ should be configured for pull up.
+
+EXAMPLE
+
+ pwrkey {
+ compatible = "qcom,pm8921-pwrkey";
+ interrupt-parent = <&pmicintc>;
+ interrupts = <50 1>, <51 1>;
+ debounce = <15625>;
+ pull-up;
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 8/9] devicetree: bindings: Document PM8921/8058 power keys
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: linux-arm-kernel
Document the power key found on PM8921 and PM8058 PMICs.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
.../bindings/input/qcom,pm8xxx-pwrkey.txt | 39 ++++++++++++++++++++++
1 file changed, 39 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt
new file mode 100644
index 000000000000..e124d9f33632
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt
@@ -0,0 +1,39 @@
+Qualcomm PM8xxx PMIC Power Key
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8058-pwrkey"
+ "qcom,pm8921-pwrkey"
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the first interrupt specifies the key release interrupt
+ and the second interrupt specifies the key press interrupt.
+ The format of the specifier is defined by the binding
+ document describing the node's interrupt parent.
+
+- debounce:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in microseconds that key must be pressed or release
+ for state change interrupt to trigger.
+
+- pull-up:
+ Usage: optional
+ Value type: <empty>
+ Definition: presence of this property indicates that the KPDPWR_N pin
+ should be configured for pull up.
+
+EXAMPLE
+
+ pwrkey {
+ compatible = "qcom,pm8921-pwrkey";
+ interrupt-parent = <&pmicintc>;
+ interrupts = <50 1>, <51 1>;
+ debounce = <15625>;
+ pull-up;
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 8/9] devicetree: bindings: Document PM8921/8058 power keys
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input, devicetree
Document the power key found on PM8921 and PM8058 PMICs.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
.../bindings/input/qcom,pm8xxx-pwrkey.txt | 39 ++++++++++++++++++++++
1 file changed, 39 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt
new file mode 100644
index 000000000000..e124d9f33632
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt
@@ -0,0 +1,39 @@
+Qualcomm PM8xxx PMIC Power Key
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8058-pwrkey"
+ "qcom,pm8921-pwrkey"
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the first interrupt specifies the key release interrupt
+ and the second interrupt specifies the key press interrupt.
+ The format of the specifier is defined by the binding
+ document describing the node's interrupt parent.
+
+- debounce:
+ Usage: optional
+ Value type: <u32>
+ Definition: time in microseconds that key must be pressed or release
+ for state change interrupt to trigger.
+
+- pull-up:
+ Usage: optional
+ Value type: <empty>
+ Definition: presence of this property indicates that the KPDPWR_N pin
+ should be configured for pull up.
+
+EXAMPLE
+
+ pwrkey {
+ compatible = "qcom,pm8921-pwrkey";
+ interrupt-parent = <&pmicintc>;
+ interrupts = <50 1>, <51 1>;
+ debounce = <15625>;
+ pull-up;
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v4 9/9] devicetree: bindings: Document PM8921/8058 vibrators
2014-02-28 1:55 ` Stephen Boyd
(?)
@ 2014-02-28 1:55 ` Stephen Boyd
-1 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input, devicetree
Document the vibration device found on PM8921 and PM8058 PMICs.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
.../devicetree/bindings/input/qcom,pm8xxx-vib.txt | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt
new file mode 100644
index 000000000000..dca1b8872cf1
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt
@@ -0,0 +1,16 @@
+Qualcomm PM8xxx PMIC Vibrator
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8058-vib"
+ "qcom,pm8921-vib"
+
+EXAMPLE
+
+ vibrator {
+ compatible = "qcom,pm8058-vib";
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 9/9] devicetree: bindings: Document PM8921/8058 vibrators
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: linux-arm-kernel
Document the vibration device found on PM8921 and PM8058 PMICs.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
.../devicetree/bindings/input/qcom,pm8xxx-vib.txt | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt
new file mode 100644
index 000000000000..dca1b8872cf1
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt
@@ -0,0 +1,16 @@
+Qualcomm PM8xxx PMIC Vibrator
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8058-vib"
+ "qcom,pm8921-vib"
+
+EXAMPLE
+
+ vibrator {
+ compatible = "qcom,pm8058-vib";
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v4 9/9] devicetree: bindings: Document PM8921/8058 vibrators
@ 2014-02-28 1:55 ` Stephen Boyd
0 siblings, 0 replies; 39+ messages in thread
From: Stephen Boyd @ 2014-02-28 1:55 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-kernel, linux-arm-msm, linux-arm-kernel, Josh Cartwright,
linux-input, devicetree
Document the vibration device found on PM8921 and PM8058 PMICs.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
.../devicetree/bindings/input/qcom,pm8xxx-vib.txt | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt
new file mode 100644
index 000000000000..dca1b8872cf1
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt
@@ -0,0 +1,16 @@
+Qualcomm PM8xxx PMIC Vibrator
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8058-vib"
+ "qcom,pm8921-vib"
+
+EXAMPLE
+
+ vibrator {
+ compatible = "qcom,pm8058-vib";
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 39+ messages in thread