* [meta-raspberry] Raspberry Pi 3 @ 2016-03-18 9:15 David Weisgerber 2016-03-31 15:26 ` Trevor Woerner 2016-07-08 13:12 ` Andrei Gherzan 0 siblings, 2 replies; 15+ messages in thread From: David Weisgerber @ 2016-03-18 9:15 UTC (permalink / raw) To: Yocto list discussion Hi, did anyone succeed in building an image that runs on Raspberry Pi 3? I set my conf/local.conf to MACHINE ??= "raspberrypi3" GPU_MEM = "128" DISABLE_OVERSCAN = "1" and built rpi-basic-image but when booting the Pi 3 up I only see 4 raspberries in the top right but nothing else happens. The image works perfectly on a Pi 2 though. Thanks for help, David ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-03-18 9:15 [meta-raspberry] Raspberry Pi 3 David Weisgerber @ 2016-03-31 15:26 ` Trevor Woerner 2016-03-31 15:29 ` Josep Puigdemont ` (2 more replies) 2016-07-08 13:12 ` Andrei Gherzan 1 sibling, 3 replies; 15+ messages in thread From: Trevor Woerner @ 2016-03-31 15:26 UTC (permalink / raw) To: David Weisgerber; +Cc: Yocto list discussion On Fri 2016-03-18 @ 10:15:39 AM, David Weisgerber wrote: > Hi, > did anyone succeed in building an image that runs on Raspberry Pi 3? I set my > conf/local.conf to > > MACHINE ??= "raspberrypi3" > GPU_MEM = "128" > DISABLE_OVERSCAN = "1" > > and built rpi-basic-image but when booting the Pi 3 up I only see 4 > raspberries in the top right but nothing else happens. The image works > perfectly on a Pi 2 though. I'm able to get a raspi3 image running on my Raspberry Pi 3, but my console is messed up. Everything works fine via the usb+hdmi ports, but plugging a console cable into the GPIO header is messed up. It looks like what happens when the baud rate is set incorrectly, but I've tried every baud rate in my terminal emulator and it all looks the same (messed up). Anyone got their console working? The same cable/setup works fine on the raspi2 (ttyAMA0) but doesn't work on my raspi3 (ttyS0). ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-03-31 15:26 ` Trevor Woerner @ 2016-03-31 15:29 ` Josep Puigdemont 2016-03-31 16:36 ` Khem Raj 2016-04-04 1:38 ` Trevor Woerner 2 siblings, 0 replies; 15+ messages in thread From: Josep Puigdemont @ 2016-03-31 15:29 UTC (permalink / raw) To: Trevor Woerner; +Cc: Yocto list discussion On Thu, Mar 31, 2016 at 11:26:04AM -0400, Trevor Woerner wrote: > On Fri 2016-03-18 @ 10:15:39 AM, David Weisgerber wrote: > > Hi, > > did anyone succeed in building an image that runs on Raspberry Pi 3? I set my > > conf/local.conf to > > > > MACHINE ??= "raspberrypi3" > > GPU_MEM = "128" > > DISABLE_OVERSCAN = "1" > > > > and built rpi-basic-image but when booting the Pi 3 up I only see 4 > > raspberries in the top right but nothing else happens. The image works > > perfectly on a Pi 2 though. > > I'm able to get a raspi3 image running on my Raspberry Pi 3, but my console is > messed up. Everything works fine via the usb+hdmi ports, but plugging a > console cable into the GPIO header is messed up. > > It looks like what happens when the baud rate is set incorrectly, but I've > tried every baud rate in my terminal emulator and it all looks the same > (messed up). > > Anyone got their console working? The same cable/setup works fine on the > raspi2 (ttyAMA0) but doesn't work on my raspi3 (ttyS0). I think you are seeing this problem: https://github.com/raspberrypi/firmware/issues/553 /Josep ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-03-31 15:26 ` Trevor Woerner 2016-03-31 15:29 ` Josep Puigdemont @ 2016-03-31 16:36 ` Khem Raj 2016-04-01 19:17 ` Trevor Woerner 2016-04-04 1:38 ` Trevor Woerner 2 siblings, 1 reply; 15+ messages in thread From: Khem Raj @ 2016-03-31 16:36 UTC (permalink / raw) To: Trevor Woerner; +Cc: Yocto list discussion [-- Attachment #1: Type: text/plain, Size: 1288 bytes --] > On Mar 31, 2016, at 8:26 AM, Trevor Woerner <twoerner@gmail.com> wrote: > > On Fri 2016-03-18 @ 10:15:39 AM, David Weisgerber wrote: >> Hi, >> did anyone succeed in building an image that runs on Raspberry Pi 3? I set my >> conf/local.conf to >> >> MACHINE ??= "raspberrypi3" >> GPU_MEM = "128" >> DISABLE_OVERSCAN = "1" >> >> and built rpi-basic-image but when booting the Pi 3 up I only see 4 >> raspberries in the top right but nothing else happens. The image works >> perfectly on a Pi 2 though. > > I'm able to get a raspi3 image running on my Raspberry Pi 3, but my console is > messed up. Everything works fine via the usb+hdmi ports, but plugging a > console cable into the GPIO header is messed up. > > It looks like what happens when the baud rate is set incorrectly, but I've > tried every baud rate in my terminal emulator and it all looks the same > (messed up). > > Anyone got their console working? The same cable/setup works fine on the > raspi2 (ttyAMA0) but doesn't work on my raspi3 (ttyS0). did you try https://www.mail-archive.com/yocto@yoctoproject.org/msg28476.html > -- > _______________________________________________ > yocto mailing list > yocto@yoctoproject.org > https://lists.yoctoproject.org/listinfo/yocto [-- Attachment #2: Message signed with OpenPGP using GPGMail --] [-- Type: application/pgp-signature, Size: 211 bytes --] ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-03-31 16:36 ` Khem Raj @ 2016-04-01 19:17 ` Trevor Woerner 2016-04-01 22:46 ` Trevor Woerner 0 siblings, 1 reply; 15+ messages in thread From: Trevor Woerner @ 2016-04-01 19:17 UTC (permalink / raw) To: Khem Raj; +Cc: Yocto list discussion On Thu 2016-03-31 @ 09:36:16 AM, Khem Raj wrote: > > > On Mar 31, 2016, at 8:26 AM, Trevor Woerner <twoerner@gmail.com> wrote: > > > > On Fri 2016-03-18 @ 10:15:39 AM, David Weisgerber wrote: > >> Hi, > >> did anyone succeed in building an image that runs on Raspberry Pi 3? I set my > >> conf/local.conf to > >> > >> MACHINE ??= "raspberrypi3" > >> GPU_MEM = "128" > >> DISABLE_OVERSCAN = "1" > >> > >> and built rpi-basic-image but when booting the Pi 3 up I only see 4 > >> raspberries in the top right but nothing else happens. The image works > >> perfectly on a Pi 2 though. > > > > I'm able to get a raspi3 image running on my Raspberry Pi 3, but my console is > > messed up. Everything works fine via the usb+hdmi ports, but plugging a > > console cable into the GPIO header is messed up. > > > > It looks like what happens when the baud rate is set incorrectly, but I've > > tried every baud rate in my terminal emulator and it all looks the same > > (messed up). > > > > Anyone got their console working? The same cable/setup works fine on the > > raspi2 (ttyAMA0) but doesn't work on my raspi3 (ttyS0). > > did you try > > https://www.mail-archive.com/yocto@yoctoproject.org/msg28476.html As far as I can tell there are two raspberry pi OE layers which include this commit: 1. git://git.yoctoproject.org/meta-raspberrypi::master 2. https://github.com/kraj/meta-raspberrypi.git::kraj/master Building two fresh, from-scratch Poky images using the latest up-to-date sources for: meta-openembedded/meta-oe openembedded-core/meta meta-poky/meta-poky and swapping in the two raspberrypi layers (one at a time) I get: - Using 1 (the official layer from Andrei) I get an image that boots but the console remains messed up (as before). - Using 2 (the layer from Khem) I get an image that flashes the rainbow pattern on the HDMI monitor, shows the 4 berries, then stops. Nothing else happens, no messages on the console. In both cases I'm building core-image-full-cmdline, and the only tweak in local.conf is: ENABLE_SPI_BUS = "1" As far as I can tell, the only difference between the two raspberry pi layers is the kernel. Andrei's uses 4.1 and Khem is using 4.4: $ git show-branch kraj/master origin/master * [kraj/master] userland: Fix tearing effect seen with wayland compositors ! [origin/master] userland: Fix tearing effect seen with wayland compositors -- + [origin/master] userland: Fix tearing effect seen with wayland compositors + [origin/master^] firmware: Update to 20160326 * [kraj/master] userland: Fix tearing effect seen with wayland compositors * [kraj/master^] firmware: Update to 20160326 * [kraj/master~2] linux-raspberrypi: Make 4.4 default kernel *+ [origin/master~2] userland: Implement dispmanx_wrap_buffer I'll try core-image-minimal and no SPI flag. Unless someone else has better-sounding ideas? Best regards, Trevor ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-04-01 19:17 ` Trevor Woerner @ 2016-04-01 22:46 ` Trevor Woerner 2016-04-01 22:55 ` Khem Raj 0 siblings, 1 reply; 15+ messages in thread From: Trevor Woerner @ 2016-04-01 22:46 UTC (permalink / raw) To: Khem Raj; +Cc: Yocto list discussion On Fri 2016-04-01 @ 03:17:29 PM, Trevor Woerner wrote: > As far as I can tell there are two raspberry pi OE layers which include this > commit: > > 1. git://git.yoctoproject.org/meta-raspberrypi::master > 2. https://github.com/kraj/meta-raspberrypi.git::kraj/master [...] > - Using 1 (the official layer from Andrei) I get an image that boots but the > console remains messed up (as before). > > - Using 2 (the layer from Khem) I get an image that flashes the rainbow > pattern on the HDMI monitor, shows the 4 berries, then stops. Nothing else > happens, no messages on the console. I get the same results with no local.conf tweaks and building the rpi-basic-image. Does anyone have a run-tested, OE-built, raspi3 image with working console? Best regards, Trevor ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-04-01 22:46 ` Trevor Woerner @ 2016-04-01 22:55 ` Khem Raj 2016-04-02 4:03 ` Trevor Woerner 0 siblings, 1 reply; 15+ messages in thread From: Khem Raj @ 2016-04-01 22:55 UTC (permalink / raw) To: Trevor Woerner; +Cc: Yocto list discussion [-- Attachment #1: Type: text/plain, Size: 1005 bytes --] > On Apr 1, 2016, at 3:46 PM, Trevor Woerner <twoerner@gmail.com> wrote: > > On Fri 2016-04-01 @ 03:17:29 PM, Trevor Woerner wrote: >> As far as I can tell there are two raspberry pi OE layers which include this >> commit: >> >> 1. git://git.yoctoproject.org/meta-raspberrypi::master >> 2. https://github.com/kraj/meta-raspberrypi.git::kraj/master > [...] >> - Using 1 (the official layer from Andrei) I get an image that boots but the >> console remains messed up (as before). >> >> - Using 2 (the layer from Khem) I get an image that flashes the rainbow >> pattern on the HDMI monitor, shows the 4 berries, then stops. Nothing else >> happens, no messages on the console. > > I get the same results with no local.conf tweaks and building the > rpi-basic-image. > > Does anyone have a run-tested, OE-built, raspi3 image with working console? > can you select 4.1 for kernel and try with master, Andre has merged all my changes today > Best regards, > Trevor [-- Attachment #2: Message signed with OpenPGP using GPGMail --] [-- Type: application/pgp-signature, Size: 211 bytes --] ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-04-01 22:55 ` Khem Raj @ 2016-04-02 4:03 ` Trevor Woerner 2016-04-02 4:56 ` Michael Dumont 2016-04-02 14:49 ` Tom Doehring 0 siblings, 2 replies; 15+ messages in thread From: Trevor Woerner @ 2016-04-02 4:03 UTC (permalink / raw) To: Khem Raj; +Cc: Yocto list discussion On Fri 2016-04-01 @ 03:55:31 PM, Khem Raj wrote: > > > On Apr 1, 2016, at 3:46 PM, Trevor Woerner <twoerner@gmail.com> wrote: > > > > On Fri 2016-04-01 @ 03:17:29 PM, Trevor Woerner wrote: > >> As far as I can tell there are two raspberry pi OE layers which include this > >> commit: > >> > >> 1. git://git.yoctoproject.org/meta-raspberrypi::master > >> 2. https://github.com/kraj/meta-raspberrypi.git::kraj/master > > [...] > >> - Using 1 (the official layer from Andrei) I get an image that boots but the > >> console remains messed up (as before). > >> > >> - Using 2 (the layer from Khem) I get an image that flashes the rainbow > >> pattern on the HDMI monitor, shows the 4 berries, then stops. Nothing else > >> happens, no messages on the console. > > > > I get the same results with no local.conf tweaks and building the > > rpi-basic-image. > > > > Does anyone have a run-tested, OE-built, raspi3 image with working console? > > > > can you select 4.1 for kernel and try with master, Andre has merged all my changes > today Yes, that's one of the options I have already tried; it boots but the console is still garbled. The 4.1 kernel is the default in Andrei's layer. Using the 4.4 kernel from your layer I can't get past the 4 raspberries. ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-04-02 4:03 ` Trevor Woerner @ 2016-04-02 4:56 ` Michael Dumont 2016-04-02 14:49 ` Tom Doehring 1 sibling, 0 replies; 15+ messages in thread From: Michael Dumont @ 2016-04-02 4:56 UTC (permalink / raw) To: Trevor Woerner; +Cc: Yocto list discussion [-- Attachment #1: Type: text/plain, Size: 2340 bytes --] Trevor, I know with the Pi3 they swapped ttyAMA0 to support Bluetooth. They put ttyS0 on the 40-pin header, but the clock used for the baud rate generation on ttyS0 is tied to the core frequency, and it can cause fluctuations when the core frequency scales up and down. I believe the official fix is to set core_freq=250 so that the core clock is always at it's lowest value and never needs to change. There's also a dtoverlay that swaps the two UARTs back so you can get the stable UART on the 40-pin header. Not clear to me that this is your exact problem, but it might be worth a quick test? Some notes here: https://www.raspberrypi.org/forums/viewtopic.php?f=107&t=138223 Hope this helps, -Mike On Fri, Apr 1, 2016 at 9:03 PM, Trevor Woerner <twoerner@gmail.com> wrote: > On Fri 2016-04-01 @ 03:55:31 PM, Khem Raj wrote: > > > > > On Apr 1, 2016, at 3:46 PM, Trevor Woerner <twoerner@gmail.com> wrote: > > > > > > On Fri 2016-04-01 @ 03:17:29 PM, Trevor Woerner wrote: > > >> As far as I can tell there are two raspberry pi OE layers which > include this > > >> commit: > > >> > > >> 1. git://git.yoctoproject.org/meta-raspberrypi::master > > >> 2. https://github.com/kraj/meta-raspberrypi.git::kraj/master > > > [...] > > >> - Using 1 (the official layer from Andrei) I get an image that boots > but the > > >> console remains messed up (as before). > > >> > > >> - Using 2 (the layer from Khem) I get an image that flashes the > rainbow > > >> pattern on the HDMI monitor, shows the 4 berries, then stops. > Nothing else > > >> happens, no messages on the console. > > > > > > I get the same results with no local.conf tweaks and building the > > > rpi-basic-image. > > > > > > Does anyone have a run-tested, OE-built, raspi3 image with working > console? > > > > > > > can you select 4.1 for kernel and try with master, Andre has merged all > my changes > > today > > Yes, that's one of the options I have already tried; it boots but the > console > is still garbled. > > The 4.1 kernel is the default in Andrei's layer. Using the 4.4 kernel from > your layer I can't get past the 4 raspberries. > -- > _______________________________________________ > yocto mailing list > yocto@yoctoproject.org > https://lists.yoctoproject.org/listinfo/yocto > [-- Attachment #2: Type: text/html, Size: 3575 bytes --] ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-04-02 4:03 ` Trevor Woerner 2016-04-02 4:56 ` Michael Dumont @ 2016-04-02 14:49 ` Tom Doehring 1 sibling, 0 replies; 15+ messages in thread From: Tom Doehring @ 2016-04-02 14:49 UTC (permalink / raw) To: yocto Trevor Woerner <twoerner@...> writes: > > On Fri 2016-04-01 <at> 03:55:31 PM, Khem Raj wrote: > > > > > On Apr 1, 2016, at 3:46 PM, Trevor Woerner <twoerner@...> wrote: > > > > > > On Fri 2016-04-01 <at> 03:17:29 PM, Trevor Woerner wrote: > > >> As far as I can tell there are two raspberry pi OE layers which include this > > >> commit: > > >> > > >> 1. git://git.yoctoproject.org/meta-raspberrypi::master > > >> 2. https://github.com/kraj/meta-raspberrypi.git::kraj/master > > > [...] > > >> - Using 1 (the official layer from Andrei) I get an image that boots but the > > >> console remains messed up (as before). > > >> > > >> - Using 2 (the layer from Khem) I get an image that flashes the rainbow > > >> pattern on the HDMI monitor, shows the 4 berries, then stops. Nothing else > > >> happens, no messages on the console. > > > > > > I get the same results with no local.conf tweaks and building the > > > rpi-basic-image. > > > > > > Does anyone have a run-tested, OE-built, raspi3 image with working console? > > > > > > > can you select 4.1 for kernel and try with master, Andre has merged all my changes > > today > > Yes, that's one of the options I have already tried; it boots but the console > is still garbled. > > The 4.1 kernel is the default in Andrei's layer. Using the 4.4 kernel from > your layer I can't get past the 4 raspberries. Hi everyone, this is nothing that depends on the kernel itself. There was a major change in the /dev/ttyAMA0 in order to make use of the bluetooth module. There is an overlay that allows using the console and the bluetooth module on parallel (pi3-miniuart-bt) with a lower baudrate while useing hciattach. If you don't want to use the bluetooth module you can switch back to the console by using the pi3-disalble-bt overlay. See also: https://www.raspberrypi.org/forums/viewtopic.php?t=138120&p=926637 ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-03-31 15:26 ` Trevor Woerner 2016-03-31 15:29 ` Josep Puigdemont 2016-03-31 16:36 ` Khem Raj @ 2016-04-04 1:38 ` Trevor Woerner 2016-04-04 2:29 ` Khem Raj 2 siblings, 1 reply; 15+ messages in thread From: Trevor Woerner @ 2016-04-04 1:38 UTC (permalink / raw) To: Yocto list discussion Thanks to everyone for their help!! It looks like I've got something working, not sure if this is a "solution" or if most would just consider it a work-around: 1) use Andrei's meta-raspberrypi layer (which selects linux kernel 4.1 by default) 2) add the following to your local.conf: SERIAL_CONSOLE_forcevariable = "115200 ttyS0" CORE_FREQ = "250" 3) ?? 4) profit!! I've tested with poky building both core-image-x11 and core-image-full-cmdline. Best regards, Trevor ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-04-04 1:38 ` Trevor Woerner @ 2016-04-04 2:29 ` Khem Raj 2016-04-04 15:08 ` Trevor Woerner 0 siblings, 1 reply; 15+ messages in thread From: Khem Raj @ 2016-04-04 2:29 UTC (permalink / raw) To: Trevor Woerner; +Cc: Yocto list discussion On Sun, Apr 3, 2016 at 6:38 PM, Trevor Woerner <twoerner@gmail.com> wrote: > Thanks to everyone for their help!! It looks like I've got something working, > not sure if this is a "solution" or if most would just consider it a > work-around: > > 1) use Andrei's meta-raspberrypi layer (which selects linux kernel 4.1 by > default) thats good. > > 2) add the following to your local.conf: > > SERIAL_CONSOLE_forcevariable = "115200 ttyS0" > CORE_FREQ = "250" Send a patch to document this in README. > > 3) ?? > > 4) profit!! > > I've tested with poky building both core-image-x11 and > core-image-full-cmdline. > > Best regards, > Trevor > -- > _______________________________________________ > yocto mailing list > yocto@yoctoproject.org > https://lists.yoctoproject.org/listinfo/yocto ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-04-04 2:29 ` Khem Raj @ 2016-04-04 15:08 ` Trevor Woerner 0 siblings, 0 replies; 15+ messages in thread From: Trevor Woerner @ 2016-04-04 15:08 UTC (permalink / raw) To: Yocto list discussion On Sun 2016-04-03 @ 07:29:59 PM, Khem Raj wrote: > On Sun, Apr 3, 2016 at 6:38 PM, Trevor Woerner <twoerner@gmail.com> wrote: > > Thanks to everyone for their help!! It looks like I've got something working, > > not sure if this is a "solution" or if most would just consider it a > > work-around: > > > > 1) use Andrei's meta-raspberrypi layer (which selects linux kernel 4.1 by > > default) > > thats good. Here's some more details that will, hopefully, help others duplicate my results: Build Configuration: BB_VERSION = "1.29.1" BUILD_SYS = "x86_64-linux" NATIVELSBSTRING = "openSUSE-project-13.2" TARGET_SYS = "arm-poky-linux-gnueabi" MACHINE = "raspberrypi3" DISTRO = "poky" DISTRO_VERSION = "2.0+snapshot-20160404" TUNE_FEATURES = "arm armv7ve vfp thumb neon vfpv4 callconvention-hard cortexa7" TARGET_FPU = "hard" meta-raspberrypi = "contrib/twoerner/raspi3:7037617fca920f6e26c2a6968fa1ec67f495035d" meta-poky meta = "master:af5f423887d1c41cf7279f6e537077726ae13082" meta-raspberrypi git://git.yoctoproject.org/meta-raspberrypi (branch based on master at 84af6e7de3b8ea64ab374028aa95dc3a288ae85c) meta-poky git://git.yoctoproject.org/poky My bblayers just pulls in these two layers, my local.conf has no local tweaks, and you need to apply the two patches I recently sent to the mailing list. > > > > > 2) add the following to your local.conf: > > > > SERIAL_CONSOLE_forcevariable = "115200 ttyS0" > > CORE_FREQ = "250" > > Send a patch to document this in README. > > > > > 3) ?? > > > > 4) profit!! > > > > I've tested with poky building both core-image-x11 and > > core-image-full-cmdline. > > > > Best regards, > > Trevor > > -- > > _______________________________________________ > > yocto mailing list > > yocto@yoctoproject.org > > https://lists.yoctoproject.org/listinfo/yocto ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-03-18 9:15 [meta-raspberry] Raspberry Pi 3 David Weisgerber 2016-03-31 15:26 ` Trevor Woerner @ 2016-07-08 13:12 ` Andrei Gherzan 2016-07-08 14:15 ` Khem Raj 1 sibling, 1 reply; 15+ messages in thread From: Andrei Gherzan @ 2016-07-08 13:12 UTC (permalink / raw) To: David Weisgerber; +Cc: Yocto list discussion [-- Attachment #1: Type: text/plain, Size: 756 bytes --] On Fri, Mar 18, 2016 at 10:15:39AM +0100, David Weisgerber wrote: > Hi, > did anyone succeed in building an image that runs on Raspberry Pi 3? I set my > conf/local.conf to > > MACHINE ??= "raspberrypi3" > GPU_MEM = "128" > DISABLE_OVERSCAN = "1" > > and built rpi-basic-image but when booting the Pi 3 up I only see 4 > raspberries in the top right but nothing else happens. The image works > perfectly on a Pi 2 though. > > Thanks for help, > David > -- > _______________________________________________ > yocto mailing list > yocto@yoctoproject.org > https://lists.yoctoproject.org/listinfo/yocto How do you check that the image is running or not? PS: Please us the correct subject tag: meta-raspberrypi. -- Andrei Gherzan [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 836 bytes --] ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [meta-raspberry] Raspberry Pi 3 2016-07-08 13:12 ` Andrei Gherzan @ 2016-07-08 14:15 ` Khem Raj 0 siblings, 0 replies; 15+ messages in thread From: Khem Raj @ 2016-07-08 14:15 UTC (permalink / raw) To: Andrei Gherzan; +Cc: Yocto list discussion On Fri, Jul 8, 2016 at 6:12 AM, Andrei Gherzan <andrei@gherzan.ro> wrote: >> MACHINE ??= "raspberrypi3" can you change it to MACHINE = "raspberrypi3" and retry ^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2016-07-08 14:16 UTC | newest] Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2016-03-18 9:15 [meta-raspberry] Raspberry Pi 3 David Weisgerber 2016-03-31 15:26 ` Trevor Woerner 2016-03-31 15:29 ` Josep Puigdemont 2016-03-31 16:36 ` Khem Raj 2016-04-01 19:17 ` Trevor Woerner 2016-04-01 22:46 ` Trevor Woerner 2016-04-01 22:55 ` Khem Raj 2016-04-02 4:03 ` Trevor Woerner 2016-04-02 4:56 ` Michael Dumont 2016-04-02 14:49 ` Tom Doehring 2016-04-04 1:38 ` Trevor Woerner 2016-04-04 2:29 ` Khem Raj 2016-04-04 15:08 ` Trevor Woerner 2016-07-08 13:12 ` Andrei Gherzan 2016-07-08 14:15 ` Khem Raj
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.