* [PATCH v3 00/13] ARM: dts: r8a779x: use demuxer for I2C
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Hi,
the intention of this series is to extend use of the demuxer for I2C
on the lager, koelsch, porter, koelsch, alt and silk boards cover all I2C IP
blocks that are either already used or exposed via an EXIO connector.
* This is based on work by Wolfram Sang.
* Testing:
- Underlying driver problems are discussed in the thread
"[PATCH v2 0/4] ARM: dts: r8a7790: lager: use demuxer for I2C"
- I have only compile tested the silk and porters patches as I do
not have access to those boards
- For all other boards I have boot tested the code and the
the default settings seem to work.
* This series is based on renesas-next-20160621-v4.7-rc1
* To aid review it is provided in git at:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git topic/i2c-demu x-v3
* I also intend to add demux for I2C for r8a7792/blanche
Changes between v2 and v3
* Group extra GPIO buses
* Add GPIO fallback for IIC1/I2C1 on Lager
* Add patches for koelsch, porter, alt and silk
Changes between v1 and v2
* Provide GPIO fallback for I2C2,
this does not seem appropriate for other I2C blocks on the lager board
Simon Horman (13):
ARM: dts: lager: rename and reindex i2cexio
ARM: dts: lager: use demuxer for IIC1/I2C1
ARM: dts: lager: use demuxer for IIC2/I2C2
ARM: dts: lager: use demuxer for IIC3/I2C3
ARM: dts: koelsch: use demuxer for I2C1
ARM: dts: koelsch: use demuxer for I2C2
ARM: dts: koelsch: use demuxer for I2C4
ARM: dts: porter: use demuxer for I2C2
ARM: dts: porter: use demuxer for I2C2
ARM: dts: koelsch: use demuxer for I2C4
ARM: dts: alt: use demuxer for I2C1
ARM: dts: alt: use demuxer for I2C4
ARM: dts: silk: use demuxer for I2C1
arch/arm/boot/dts/r8a7790-lager.dts | 275 +++++++++++++++++++++++-----------
arch/arm/boot/dts/r8a7791-koelsch.dts | 209 +++++++++++++++++++-------
arch/arm/boot/dts/r8a7791-porter.dts | 129 +++++++++-------
arch/arm/boot/dts/r8a7793-gose.dts | 147 ++++++++++++------
arch/arm/boot/dts/r8a7794-alt.dts | 87 +++++++++--
arch/arm/boot/dts/r8a7794-silk.dts | 117 +++++++++------
6 files changed, 658 insertions(+), 306 deletions(-)
--
2.1.4
^ permalink raw reply [flat|nested] 34+ messages in thread
* [PATCH v3 00/13] ARM: dts: r8a779x: use demuxer for I2C
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
the intention of this series is to extend use of the demuxer for I2C
on the lager, koelsch, porter, koelsch, alt and silk boards cover all I2C IP
blocks that are either already used or exposed via an EXIO connector.
* This is based on work by Wolfram Sang.
* Testing:
- Underlying driver problems are discussed in the thread
"[PATCH v2 0/4] ARM: dts: r8a7790: lager: use demuxer for I2C"
- I have only compile tested the silk and porters patches as I do
not have access to those boards
- For all other boards I have boot tested the code and the
the default settings seem to work.
* This series is based on renesas-next-20160621-v4.7-rc1
* To aid review it is provided in git at:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git topic/i2c-demu x-v3
* I also intend to add demux for I2C for r8a7792/blanche
Changes between v2 and v3
* Group extra GPIO buses
* Add GPIO fallback for IIC1/I2C1 on Lager
* Add patches for koelsch, porter, alt and silk
Changes between v1 and v2
* Provide GPIO fallback for I2C2,
this does not seem appropriate for other I2C blocks on the lager board
Simon Horman (13):
ARM: dts: lager: rename and reindex i2cexio
ARM: dts: lager: use demuxer for IIC1/I2C1
ARM: dts: lager: use demuxer for IIC2/I2C2
ARM: dts: lager: use demuxer for IIC3/I2C3
ARM: dts: koelsch: use demuxer for I2C1
ARM: dts: koelsch: use demuxer for I2C2
ARM: dts: koelsch: use demuxer for I2C4
ARM: dts: porter: use demuxer for I2C2
ARM: dts: porter: use demuxer for I2C2
ARM: dts: koelsch: use demuxer for I2C4
ARM: dts: alt: use demuxer for I2C1
ARM: dts: alt: use demuxer for I2C4
ARM: dts: silk: use demuxer for I2C1
arch/arm/boot/dts/r8a7790-lager.dts | 275 +++++++++++++++++++++++-----------
arch/arm/boot/dts/r8a7791-koelsch.dts | 209 +++++++++++++++++++-------
arch/arm/boot/dts/r8a7791-porter.dts | 129 +++++++++-------
arch/arm/boot/dts/r8a7793-gose.dts | 147 ++++++++++++------
arch/arm/boot/dts/r8a7794-alt.dts | 87 +++++++++--
arch/arm/boot/dts/r8a7794-silk.dts | 117 +++++++++------
6 files changed, 658 insertions(+), 306 deletions(-)
--
2.1.4
^ permalink raw reply [flat|nested] 34+ messages in thread
* [PATCH v3 01/13] ARM: dts: lager: rename and reindex i2cexio
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
The rename from i2cexio to i2cexio0 is in in preparation for adding
i2cexio1 which will use the dmuxer for IIC1/I2C1.
The reindexing from i2c8 to i2c10 is to allow space for grouping of
additional GPIO buses to added by follow-up patches to support demuxing of
other i2c buses.
Also note that fallback to GPIO is not provided by the hardware for IIC1/I2C1.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v2:
* Reindex i2c
* Add note that GPIO fallback is not provided by hardware
---
arch/arm/boot/dts/r8a7790-lager.dts | 12 +++++++-----
1 file changed, 7 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 52b56fcaddf2..6b25d9e7d21b 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -50,7 +50,7 @@
aliases {
serial0 = &scif0;
serial1 = &scifa1;
- i2c8 = "i2cexio";
+ i2c10 = "i2cexio0";
};
chosen {
@@ -262,11 +262,13 @@
* bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
* instantiate the slave device at runtime according to the documentation.
* You can then communicate with the slave via IIC3.
+ *
+ * IIC0/I2C0 does not appear to support fallback to GPIO.
*/
- i2cexio: i2c-8 {
+ i2cexio0: i2c-10 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&iic0>, <&i2c0>;
- i2c-bus-name = "i2c-exio";
+ i2c-bus-name = "i2c-exio0";
#address-cells = <1>;
#size-cells = <0>;
};
@@ -580,12 +582,12 @@
&i2c0 {
pinctrl-0 = <&i2c0_pins>;
- pinctrl-names = "i2c-exio";
+ pinctrl-names = "i2c-exio0";
};
&iic0 {
pinctrl-0 = <&iic0_pins>;
- pinctrl-names = "i2c-exio";
+ pinctrl-names = "i2c-exio0";
};
&iic1 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 01/13] ARM: dts: lager: rename and reindex i2cexio
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
The rename from i2cexio to i2cexio0 is in in preparation for adding
i2cexio1 which will use the dmuxer for IIC1/I2C1.
The reindexing from i2c8 to i2c10 is to allow space for grouping of
additional GPIO buses to added by follow-up patches to support demuxing of
other i2c buses.
Also note that fallback to GPIO is not provided by the hardware for IIC1/I2C1.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v2:
* Reindex i2c
* Add note that GPIO fallback is not provided by hardware
---
arch/arm/boot/dts/r8a7790-lager.dts | 12 +++++++-----
1 file changed, 7 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 52b56fcaddf2..6b25d9e7d21b 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -50,7 +50,7 @@
aliases {
serial0 = &scif0;
serial1 = &scifa1;
- i2c8 = "i2cexio";
+ i2c10 = "i2cexio0";
};
chosen {
@@ -262,11 +262,13 @@
* bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
* instantiate the slave device at runtime according to the documentation.
* You can then communicate with the slave via IIC3.
+ *
+ * IIC0/I2C0 does not appear to support fallback to GPIO.
*/
- i2cexio: i2c-8 {
+ i2cexio0: i2c-10 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&iic0>, <&i2c0>;
- i2c-bus-name = "i2c-exio";
+ i2c-bus-name = "i2c-exio0";
#address-cells = <1>;
#size-cells = <0>;
};
@@ -580,12 +582,12 @@
&i2c0 {
pinctrl-0 = <&i2c0_pins>;
- pinctrl-names = "i2c-exio";
+ pinctrl-names = "i2c-exio0";
};
&iic0 {
pinctrl-0 = <&iic0_pins>;
- pinctrl-names = "i2c-exio";
+ pinctrl-names = "i2c-exio0";
};
&iic1 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 02/13] ARM: dts: lager: use demuxer for IIC1/I2C1
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Make it possible to select which I2C1 IP core you want to run on the
EXIO-A connector.
This is based on reference work for the I2C0 core of the lager board
by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* Add GPIO fallback
* Re-order buses to facilitate grouping of additional GPIO buses
v2
* No change
---
arch/arm/boot/dts/r8a7790-lager.dts | 39 +++++++++++++++++++++++++++++++++++--
1 file changed, 37 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 6b25d9e7d21b..05302d0d7e33 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -50,7 +50,9 @@
aliases {
serial0 = &scif0;
serial1 = &scifa1;
+ i2c8 = "gpioi2c1";
i2c10 = "i2cexio0";
+ i2c11 = "i2cexio1";
};
chosen {
@@ -254,6 +256,17 @@
clock-frequency = <148500000>;
};
+ gpioi2c1: i2c-8 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio1 17 GPIO_ACTIVE_HIGH /* sda */
+ &gpio1 16 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
* We use the I2C demuxer, so the desired IP core can be selected at runtime
@@ -272,6 +285,19 @@
#address-cells = <1>;
#size-cells = <0>;
};
+
+ /*
+ * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
+ * This is similar to the arangement described for i2cexio0 (above)
+ * with a fallback to GPIO also provided.
+ */
+ i2cexio1: i2c-11 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
+ i2c-bus-name = "i2c-exio1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
&du {
@@ -394,6 +420,11 @@
function = "iic0";
};
+ i2c1_pins: i2c1 {
+ groups = "i2c1";
+ function = "i2c1";
+ };
+
iic1_pins: iic1 {
groups = "iic1";
function = "iic1";
@@ -590,10 +621,14 @@
pinctrl-names = "i2c-exio0";
};
+&i2c1 {
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-names = "i2c-exio1";
+};
+
&iic1 {
- status = "okay";
pinctrl-0 = <&iic1_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-exio1";
};
&iic2 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 02/13] ARM: dts: lager: use demuxer for IIC1/I2C1
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Make it possible to select which I2C1 IP core you want to run on the
EXIO-A connector.
This is based on reference work for the I2C0 core of the lager board
by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* Add GPIO fallback
* Re-order buses to facilitate grouping of additional GPIO buses
v2
* No change
---
arch/arm/boot/dts/r8a7790-lager.dts | 39 +++++++++++++++++++++++++++++++++++--
1 file changed, 37 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 6b25d9e7d21b..05302d0d7e33 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -50,7 +50,9 @@
aliases {
serial0 = &scif0;
serial1 = &scifa1;
+ i2c8 = "gpioi2c1";
i2c10 = "i2cexio0";
+ i2c11 = "i2cexio1";
};
chosen {
@@ -254,6 +256,17 @@
clock-frequency = <148500000>;
};
+ gpioi2c1: i2c-8 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio1 17 GPIO_ACTIVE_HIGH /* sda */
+ &gpio1 16 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
* We use the I2C demuxer, so the desired IP core can be selected at runtime
@@ -272,6 +285,19 @@
#address-cells = <1>;
#size-cells = <0>;
};
+
+ /*
+ * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
+ * This is similar to the arangement described for i2cexio0 (above)
+ * with a fallback to GPIO also provided.
+ */
+ i2cexio1: i2c-11 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
+ i2c-bus-name = "i2c-exio1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
&du {
@@ -394,6 +420,11 @@
function = "iic0";
};
+ i2c1_pins: i2c1 {
+ groups = "i2c1";
+ function = "i2c1";
+ };
+
iic1_pins: iic1 {
groups = "iic1";
function = "iic1";
@@ -590,10 +621,14 @@
pinctrl-names = "i2c-exio0";
};
+&i2c1 {
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-names = "i2c-exio1";
+};
+
&iic1 {
- status = "okay";
pinctrl-0 = <&iic1_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-exio1";
};
&iic2 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 03/13] ARM: dts: lager: use demuxer for IIC2/I2C2
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Create a separate bus for HDMI related I2C slaves.
Based on work by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* Name GPIO i2c node gpioi2c2 instead of gpioi2c2 as there
is now another gpioi2c node
* Add a small comment documenting that IIC2/I2C2 may be switched
and that a GPIO fallback is provided.
* Group additional GPIO buses
v2
* No change
---
arch/arm/boot/dts/r8a7790-lager.dts | 142 ++++++++++++++++++++++--------------
1 file changed, 89 insertions(+), 53 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 05302d0d7e33..862d766b932b 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -51,8 +51,10 @@
serial0 = &scif0;
serial1 = &scifa1;
i2c8 = "gpioi2c1";
+ i2c9 = "gpioi2c2";
i2c10 = "i2cexio0";
i2c11 = "i2cexio1";
+ i2c12 = "i2chdmi";
};
chosen {
@@ -267,6 +269,17 @@
i2c-gpio,delay-us = <5>;
};
+ gpioi2c2: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio5 6 GPIO_ACTIVE_HIGH /* sda */
+ &gpio5 5 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
* We use the I2C demuxer, so the desired IP core can be selected at runtime
@@ -298,6 +311,69 @@
#address-cells = <1>;
#size-cells = <0>;
};
+
+ /*
+ * IIC2 and I2C2 may be switched using pinmux.
+ * A fallback to GPIO also provided.
+ */
+ i2chdmi: i2c-12 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ak4643: codec@12 {
+ compatible = "asahi-kasei,ak4643";
+ #sound-dai-cells = <0>;
+ reg = <0x12>;
+ };
+
+ composite-in@20 {
+ compatible = "adi,adv7180";
+ reg = <0x20>;
+ remote = <&vin1>;
+
+ port {
+ adv7180: endpoint {
+ bus-width = <8>;
+ remote-endpoint = <&vin1ep0>;
+ };
+ };
+ };
+
+ hdmi@39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_lvds0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+ };
};
&du {
@@ -430,6 +506,11 @@
function = "iic1";
};
+ i2c2_pins: i2c2 {
+ groups = "i2c2";
+ function = "i2c2";
+ };
+
iic2_pins: iic2 {
groups = "iic2";
function = "iic2";
@@ -631,63 +712,18 @@
pinctrl-names = "i2c-exio1";
};
-&iic2 {
- status = "okay";
- pinctrl-0 = <&iic2_pins>;
- pinctrl-names = "default";
+&i2c2 {
+ pinctrl-0 = <&i2c2_pins>;
+ pinctrl-names = "i2c-hdmi";
clock-frequency = <100000>;
+};
- ak4643: codec@12 {
- compatible = "asahi-kasei,ak4643";
- #sound-dai-cells = <0>;
- reg = <0x12>;
- };
-
- composite-in@20 {
- compatible = "adi,adv7180";
- reg = <0x20>;
- remote = <&vin1>;
-
- port {
- adv7180: endpoint {
- bus-width = <8>;
- remote-endpoint = <&vin1ep0>;
- };
- };
- };
-
- hdmi@39 {
- compatible = "adi,adv7511w";
- reg = <0x39>;
- interrupt-parent = <&gpio1>;
- interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&du_out_lvds0>;
- };
- };
+&iic2 {
+ pinctrl-0 = <&iic2_pins>;
+ pinctrl-names = "i2c-hdmi";
- port@1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
+ clock-frequency = <100000>;
};
&iic3 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 03/13] ARM: dts: lager: use demuxer for IIC2/I2C2
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Create a separate bus for HDMI related I2C slaves.
Based on work by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* Name GPIO i2c node gpioi2c2 instead of gpioi2c2 as there
is now another gpioi2c node
* Add a small comment documenting that IIC2/I2C2 may be switched
and that a GPIO fallback is provided.
* Group additional GPIO buses
v2
* No change
---
arch/arm/boot/dts/r8a7790-lager.dts | 142 ++++++++++++++++++++++--------------
1 file changed, 89 insertions(+), 53 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 05302d0d7e33..862d766b932b 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -51,8 +51,10 @@
serial0 = &scif0;
serial1 = &scifa1;
i2c8 = "gpioi2c1";
+ i2c9 = "gpioi2c2";
i2c10 = "i2cexio0";
i2c11 = "i2cexio1";
+ i2c12 = "i2chdmi";
};
chosen {
@@ -267,6 +269,17 @@
i2c-gpio,delay-us = <5>;
};
+ gpioi2c2: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio5 6 GPIO_ACTIVE_HIGH /* sda */
+ &gpio5 5 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
* We use the I2C demuxer, so the desired IP core can be selected at runtime
@@ -298,6 +311,69 @@
#address-cells = <1>;
#size-cells = <0>;
};
+
+ /*
+ * IIC2 and I2C2 may be switched using pinmux.
+ * A fallback to GPIO also provided.
+ */
+ i2chdmi: i2c-12 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ak4643: codec at 12 {
+ compatible = "asahi-kasei,ak4643";
+ #sound-dai-cells = <0>;
+ reg = <0x12>;
+ };
+
+ composite-in at 20 {
+ compatible = "adi,adv7180";
+ reg = <0x20>;
+ remote = <&vin1>;
+
+ port {
+ adv7180: endpoint {
+ bus-width = <8>;
+ remote-endpoint = <&vin1ep0>;
+ };
+ };
+ };
+
+ hdmi at 39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_lvds0>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+ };
};
&du {
@@ -430,6 +506,11 @@
function = "iic1";
};
+ i2c2_pins: i2c2 {
+ groups = "i2c2";
+ function = "i2c2";
+ };
+
iic2_pins: iic2 {
groups = "iic2";
function = "iic2";
@@ -631,63 +712,18 @@
pinctrl-names = "i2c-exio1";
};
-&iic2 {
- status = "okay";
- pinctrl-0 = <&iic2_pins>;
- pinctrl-names = "default";
+&i2c2 {
+ pinctrl-0 = <&i2c2_pins>;
+ pinctrl-names = "i2c-hdmi";
clock-frequency = <100000>;
+};
- ak4643: codec at 12 {
- compatible = "asahi-kasei,ak4643";
- #sound-dai-cells = <0>;
- reg = <0x12>;
- };
-
- composite-in at 20 {
- compatible = "adi,adv7180";
- reg = <0x20>;
- remote = <&vin1>;
-
- port {
- adv7180: endpoint {
- bus-width = <8>;
- remote-endpoint = <&vin1ep0>;
- };
- };
- };
-
- hdmi at 39 {
- compatible = "adi,adv7511w";
- reg = <0x39>;
- interrupt-parent = <&gpio1>;
- interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&du_out_lvds0>;
- };
- };
+&iic2 {
+ pinctrl-0 = <&iic2_pins>;
+ pinctrl-names = "i2c-hdmi";
- port at 1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
+ clock-frequency = <100000>;
};
&iic3 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 04/13] ARM: dts: lager: use demuxer for IIC3/I2C3
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Create a separate bus for dla98063 PMIC and da9210 regulator
related I2C slaves.
Based on similar work for HDMI by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* Add a small commend documenting that IIC3/I2C3 may be switched
and that a GPIO fallback not provided.
v2
* No change
---
arch/arm/boot/dts/r8a7790-lager.dts | 84 +++++++++++++++++++++++--------------
1 file changed, 53 insertions(+), 31 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 862d766b932b..626b55369871 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -55,6 +55,7 @@
i2c10 = "i2cexio0";
i2c11 = "i2cexio1";
i2c12 = "i2chdmi";
+ i2c13 = "i2cpwr";
};
chosen {
@@ -374,6 +375,46 @@
};
};
};
+
+ /*
+ * IIC3 and I2C3 may be switched using pinmux.
+ * IIC3/I2C3 does not appear to support fallback to GPIO.
+ */
+ i2cpwr: i2c-13 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&iic3>, <&i2c3>;
+ i2c-bus-name = "i2c-pwr";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@58 {
+ compatible = "dlg,da9063";
+ reg = <0x58>;
+ interrupt-parent = <&irqc0>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+
+ rtc {
+ compatible = "dlg,da9063-rtc";
+ };
+
+ wdt {
+ compatible = "dlg,da9063-watchdog";
+ };
+ };
+
+ vdd_dvfs: regulator@68 {
+ compatible = "dlg,da9210";
+ reg = <0x68>;
+ interrupt-parent = <&irqc0>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
};
&du {
@@ -516,6 +557,11 @@
function = "iic2";
};
+ i2c3_pins: i2c3 {
+ groups = "i2c3";
+ function = "i2c3";
+ };
+
iic3_pins: iic3 {
groups = "iic3";
function = "iic3";
@@ -726,38 +772,14 @@
clock-frequency = <100000>;
};
-&iic3 {
- pinctrl-names = "default";
- pinctrl-0 = <&iic3_pins>;
- status = "okay";
-
- pmic@58 {
- compatible = "dlg,da9063";
- reg = <0x58>;
- interrupt-parent = <&irqc0>;
- interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
-
- rtc {
- compatible = "dlg,da9063-rtc";
- };
-
- wdt {
- compatible = "dlg,da9063-watchdog";
- };
- };
-
- vdd_dvfs: regulator@68 {
- compatible = "dlg,da9210";
- reg = <0x68>;
- interrupt-parent = <&irqc0>;
- interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+&i2c3 {
+ pinctrl-0 = <&i2c3_pins>;
+ pinctrl-names = "i2c-pwr";
+};
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-boot-on;
- regulator-always-on;
- };
+&iic3 {
+ pinctrl-0 = <&iic3_pins>;
+ pinctrl-names = "i2c-pwr";
};
&pci0 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 04/13] ARM: dts: lager: use demuxer for IIC3/I2C3
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Create a separate bus for dla98063 PMIC and da9210 regulator
related I2C slaves.
Based on similar work for HDMI by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* Add a small commend documenting that IIC3/I2C3 may be switched
and that a GPIO fallback not provided.
v2
* No change
---
arch/arm/boot/dts/r8a7790-lager.dts | 84 +++++++++++++++++++++++--------------
1 file changed, 53 insertions(+), 31 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 862d766b932b..626b55369871 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -55,6 +55,7 @@
i2c10 = "i2cexio0";
i2c11 = "i2cexio1";
i2c12 = "i2chdmi";
+ i2c13 = "i2cpwr";
};
chosen {
@@ -374,6 +375,46 @@
};
};
};
+
+ /*
+ * IIC3 and I2C3 may be switched using pinmux.
+ * IIC3/I2C3 does not appear to support fallback to GPIO.
+ */
+ i2cpwr: i2c-13 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&iic3>, <&i2c3>;
+ i2c-bus-name = "i2c-pwr";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic at 58 {
+ compatible = "dlg,da9063";
+ reg = <0x58>;
+ interrupt-parent = <&irqc0>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+
+ rtc {
+ compatible = "dlg,da9063-rtc";
+ };
+
+ wdt {
+ compatible = "dlg,da9063-watchdog";
+ };
+ };
+
+ vdd_dvfs: regulator at 68 {
+ compatible = "dlg,da9210";
+ reg = <0x68>;
+ interrupt-parent = <&irqc0>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
};
&du {
@@ -516,6 +557,11 @@
function = "iic2";
};
+ i2c3_pins: i2c3 {
+ groups = "i2c3";
+ function = "i2c3";
+ };
+
iic3_pins: iic3 {
groups = "iic3";
function = "iic3";
@@ -726,38 +772,14 @@
clock-frequency = <100000>;
};
-&iic3 {
- pinctrl-names = "default";
- pinctrl-0 = <&iic3_pins>;
- status = "okay";
-
- pmic at 58 {
- compatible = "dlg,da9063";
- reg = <0x58>;
- interrupt-parent = <&irqc0>;
- interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
-
- rtc {
- compatible = "dlg,da9063-rtc";
- };
-
- wdt {
- compatible = "dlg,da9063-watchdog";
- };
- };
-
- vdd_dvfs: regulator at 68 {
- compatible = "dlg,da9210";
- reg = <0x68>;
- interrupt-parent = <&irqc0>;
- interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+&i2c3 {
+ pinctrl-0 = <&i2c3_pins>;
+ pinctrl-names = "i2c-pwr";
+};
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-boot-on;
- regulator-always-on;
- };
+&iic3 {
+ pinctrl-0 = <&iic3_pins>;
+ pinctrl-names = "i2c-pwr";
};
&pci0 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 05/13] ARM: dts: koelsch: use demuxer for I2C1
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Make it possible to fallback to GPIO for I2C1 on the EXIO-C connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New Patch
---
arch/arm/boot/dts/r8a7791-koelsch.dts | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index f8a7d090fd01..744a6e2be2d2 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -50,6 +50,8 @@
aliases {
serial0 = &scif0;
serial1 = &scif1;
+ i2c9 = "gpioi2c1";
+ i2c12 = "i2cexio1";
};
chosen {
@@ -287,6 +289,29 @@
#clock-cells = <0>;
clock-frequency = <148500000>;
};
+
+ gpioi2c1: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio7 16 GPIO_ACTIVE_HIGH /* sda */
+ &gpio7 15 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
+ /*
+ * I2C1 is routed to EXIO connector B, pins 64 (SCL) + 66 (SDA).
+ * A fallback to GPIO is provided.
+ */
+ i2cexio1: i2c-12 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c1>, <&gpioi2c1>;
+ i2c-bus-name = "i2c-exio1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
&du {
@@ -322,6 +347,11 @@
pinctrl-0 = <&scif_clk_pins>;
pinctrl-names = "default";
+ i2c1_pins: i2c1 {
+ groups = "i2c1";
+ function = "i2c1";
+ };
+
i2c2_pins: i2c2 {
groups = "i2c2";
function = "i2c2";
@@ -538,6 +568,11 @@
};
};
+&i2c1 {
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-names = "i2c-exio1";
+};
+
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
pinctrl-names = "default";
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 05/13] ARM: dts: koelsch: use demuxer for I2C1
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Make it possible to fallback to GPIO for I2C1 on the EXIO-C connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New Patch
---
arch/arm/boot/dts/r8a7791-koelsch.dts | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index f8a7d090fd01..744a6e2be2d2 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -50,6 +50,8 @@
aliases {
serial0 = &scif0;
serial1 = &scif1;
+ i2c9 = "gpioi2c1";
+ i2c12 = "i2cexio1";
};
chosen {
@@ -287,6 +289,29 @@
#clock-cells = <0>;
clock-frequency = <148500000>;
};
+
+ gpioi2c1: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio7 16 GPIO_ACTIVE_HIGH /* sda */
+ &gpio7 15 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
+ /*
+ * I2C1 is routed to EXIO connector B, pins 64 (SCL) + 66 (SDA).
+ * A fallback to GPIO is provided.
+ */
+ i2cexio1: i2c-12 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c1>, <&gpioi2c1>;
+ i2c-bus-name = "i2c-exio1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
&du {
@@ -322,6 +347,11 @@
pinctrl-0 = <&scif_clk_pins>;
pinctrl-names = "default";
+ i2c1_pins: i2c1 {
+ groups = "i2c1";
+ function = "i2c1";
+ };
+
i2c2_pins: i2c2 {
groups = "i2c2";
function = "i2c2";
@@ -538,6 +568,11 @@
};
};
+&i2c1 {
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-names = "i2c-exio1";
+};
+
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
pinctrl-names = "default";
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 06/13] ARM: dts: koelsch: use demuxer for I2C2
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New patch
---
arch/arm/boot/dts/r8a7791-koelsch.dts | 141 ++++++++++++++++++++--------------
1 file changed, 82 insertions(+), 59 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 744a6e2be2d2..0beb9556fe01 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -51,7 +51,9 @@
serial0 = &scif0;
serial1 = &scif1;
i2c9 = "gpioi2c1";
+ i2c10 = "gpioi2c2";
i2c12 = "i2cexio1";
+ i2c13 = "i2chdmi";
};
chosen {
@@ -301,6 +303,17 @@
i2c-gpio,delay-us = <5>;
};
+ gpioi2c2: i2c-10 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio2 7 GPIO_ACTIVE_HIGH /* sda */
+ &gpio2 6 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* I2C1 is routed to EXIO connector B, pins 64 (SCL) + 66 (SDA).
* A fallback to GPIO is provided.
@@ -312,6 +325,74 @@
#address-cells = <1>;
#size-cells = <0>;
};
+
+ /*
+ * A fallback to GPIO is provided for I2C2.
+ */
+ i2chdmi: i2c-13 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c2>, <&gpioi2c2>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ak4643: codec@12 {
+ compatible = "asahi-kasei,ak4643";
+ #sound-dai-cells = <0>;
+ reg = <0x12>;
+ };
+
+ composite-in@20 {
+ compatible = "adi,adv7180";
+ reg = <0x20>;
+ remote = <&vin1>;
+
+ port {
+ adv7180: endpoint {
+ bus-width = <8>;
+ remote-endpoint = <&vin1ep>;
+ };
+ };
+ };
+
+ hdmi@39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_rgb>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+
+ eeprom@50 {
+ compatible = "renesas,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+ };
};
&du {
@@ -575,67 +656,9 @@
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-hdmi";
- status = "okay";
clock-frequency = <100000>;
-
- ak4643: codec@12 {
- compatible = "asahi-kasei,ak4643";
- #sound-dai-cells = <0>;
- reg = <0x12>;
- };
-
- composite-in@20 {
- compatible = "adi,adv7180";
- reg = <0x20>;
- remote = <&vin1>;
-
- port {
- adv7180: endpoint {
- bus-width = <8>;
- remote-endpoint = <&vin1ep>;
- };
- };
- };
-
- hdmi@39 {
- compatible = "adi,adv7511w";
- reg = <0x39>;
- interrupt-parent = <&gpio3>;
- interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&du_out_rgb>;
- };
- };
-
- port@1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
-
- eeprom@50 {
- compatible = "renesas,24c02";
- reg = <0x50>;
- pagesize = <16>;
- };
};
&i2c6 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 06/13] ARM: dts: koelsch: use demuxer for I2C2
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New patch
---
arch/arm/boot/dts/r8a7791-koelsch.dts | 141 ++++++++++++++++++++--------------
1 file changed, 82 insertions(+), 59 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 744a6e2be2d2..0beb9556fe01 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -51,7 +51,9 @@
serial0 = &scif0;
serial1 = &scif1;
i2c9 = "gpioi2c1";
+ i2c10 = "gpioi2c2";
i2c12 = "i2cexio1";
+ i2c13 = "i2chdmi";
};
chosen {
@@ -301,6 +303,17 @@
i2c-gpio,delay-us = <5>;
};
+ gpioi2c2: i2c-10 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio2 7 GPIO_ACTIVE_HIGH /* sda */
+ &gpio2 6 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* I2C1 is routed to EXIO connector B, pins 64 (SCL) + 66 (SDA).
* A fallback to GPIO is provided.
@@ -312,6 +325,74 @@
#address-cells = <1>;
#size-cells = <0>;
};
+
+ /*
+ * A fallback to GPIO is provided for I2C2.
+ */
+ i2chdmi: i2c-13 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c2>, <&gpioi2c2>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ak4643: codec at 12 {
+ compatible = "asahi-kasei,ak4643";
+ #sound-dai-cells = <0>;
+ reg = <0x12>;
+ };
+
+ composite-in at 20 {
+ compatible = "adi,adv7180";
+ reg = <0x20>;
+ remote = <&vin1>;
+
+ port {
+ adv7180: endpoint {
+ bus-width = <8>;
+ remote-endpoint = <&vin1ep>;
+ };
+ };
+ };
+
+ hdmi at 39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_rgb>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+
+ eeprom at 50 {
+ compatible = "renesas,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+ };
};
&du {
@@ -575,67 +656,9 @@
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-hdmi";
- status = "okay";
clock-frequency = <100000>;
-
- ak4643: codec at 12 {
- compatible = "asahi-kasei,ak4643";
- #sound-dai-cells = <0>;
- reg = <0x12>;
- };
-
- composite-in at 20 {
- compatible = "adi,adv7180";
- reg = <0x20>;
- remote = <&vin1>;
-
- port {
- adv7180: endpoint {
- bus-width = <8>;
- remote-endpoint = <&vin1ep>;
- };
- };
- };
-
- hdmi at 39 {
- compatible = "adi,adv7511w";
- reg = <0x39>;
- interrupt-parent = <&gpio3>;
- interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&du_out_rgb>;
- };
- };
-
- port at 1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
-
- eeprom at 50 {
- compatible = "renesas,24c02";
- reg = <0x50>;
- pagesize = <16>;
- };
};
&i2c6 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 07/13] ARM: dts: koelsch: use demuxer for I2C4
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Make it possible to fallback to GPIO for I2C4 on the EXIO-E connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New Patch
---
arch/arm/boot/dts/r8a7791-koelsch.dts | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 0beb9556fe01..980f41b70fed 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -52,8 +52,10 @@
serial1 = &scif1;
i2c9 = "gpioi2c1";
i2c10 = "gpioi2c2";
+ i2c11 = "gpioi2c4";
i2c12 = "i2cexio1";
i2c13 = "i2chdmi";
+ i2c14 = "i2cexio4";
};
chosen {
@@ -314,6 +316,17 @@
i2c-gpio,delay-us = <5>;
};
+ gpioi2c4: i2c-11 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio7 14 GPIO_ACTIVE_HIGH /* sda */
+ &gpio7 13 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* I2C1 is routed to EXIO connector B, pins 64 (SCL) + 66 (SDA).
* A fallback to GPIO is provided.
@@ -393,6 +406,18 @@
pagesize = <16>;
};
};
+
+ /*
+ * I2C4 is routed to EXIO connector E, pins 37 (SCL) + 39 (SDA).
+ * A fallback to GPIO is provided.
+ */
+ i2cexio4: i2c-14 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c4>, <&gpioi2c4>;
+ i2c-bus-name = "i2c-exio4";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
&du {
@@ -438,6 +463,11 @@
function = "i2c2";
};
+ i2c4_pins: i2c4 {
+ groups = "i2c4";
+ function = "i2c4";
+ };
+
du_pins: du {
groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
function = "du";
@@ -661,6 +691,11 @@
clock-frequency = <100000>;
};
+&i2c4 {
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "i2c-exio4";
+};
+
&i2c6 {
status = "okay";
clock-frequency = <100000>;
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 07/13] ARM: dts: koelsch: use demuxer for I2C4
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Make it possible to fallback to GPIO for I2C4 on the EXIO-E connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New Patch
---
arch/arm/boot/dts/r8a7791-koelsch.dts | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 0beb9556fe01..980f41b70fed 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -52,8 +52,10 @@
serial1 = &scif1;
i2c9 = "gpioi2c1";
i2c10 = "gpioi2c2";
+ i2c11 = "gpioi2c4";
i2c12 = "i2cexio1";
i2c13 = "i2chdmi";
+ i2c14 = "i2cexio4";
};
chosen {
@@ -314,6 +316,17 @@
i2c-gpio,delay-us = <5>;
};
+ gpioi2c4: i2c-11 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio7 14 GPIO_ACTIVE_HIGH /* sda */
+ &gpio7 13 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* I2C1 is routed to EXIO connector B, pins 64 (SCL) + 66 (SDA).
* A fallback to GPIO is provided.
@@ -393,6 +406,18 @@
pagesize = <16>;
};
};
+
+ /*
+ * I2C4 is routed to EXIO connector E, pins 37 (SCL) + 39 (SDA).
+ * A fallback to GPIO is provided.
+ */
+ i2cexio4: i2c-14 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c4>, <&gpioi2c4>;
+ i2c-bus-name = "i2c-exio4";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
&du {
@@ -438,6 +463,11 @@
function = "i2c2";
};
+ i2c4_pins: i2c4 {
+ groups = "i2c4";
+ function = "i2c4";
+ };
+
du_pins: du {
groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
function = "du";
@@ -661,6 +691,11 @@
clock-frequency = <100000>;
};
+&i2c4 {
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "i2c-exio4";
+};
+
&i2c6 {
status = "okay";
clock-frequency = <100000>;
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 08/13] ARM: dts: porter: use demuxer for I2C2
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New patch
* Compile tested only
---
arch/arm/boot/dts/r8a7791-porter.dts | 129 +++++++++++++++++++++--------------
1 file changed, 76 insertions(+), 53 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts
index 6761d11d3f9e..dea3c1a103a5 100644
--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/r8a7791-porter.dts
@@ -29,6 +29,8 @@
aliases {
serial0 = &scif0;
+ i2c9 = "gpioi2c2";
+ i2c10 = "i2chdmi";
};
chosen {
@@ -135,6 +137,79 @@
clocks = <&x14_clk>;
};
};
+
+ gpioi2c2: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio2 7 GPIO_ACTIVE_HIGH /* sda */
+ &gpio2 6 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
+ /*
+ * A fallback to GPIO is provided for I2C2.
+ */
+ i2chdmi: i2c-10 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c2>, <&gpioi2c2>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ak4642: codec@12 {
+ compatible = "asahi-kasei,ak4642";
+ #sound-dai-cells = <0>;
+ reg = <0x12>;
+ };
+
+ composite-in@20 {
+ compatible = "adi,adv7180";
+ reg = <0x20>;
+ remote = <&vin0>;
+
+ port {
+ adv7180: endpoint {
+ bus-width = <8>;
+ remote-endpoint = <&vin0ep>;
+ };
+ };
+ };
+
+ hdmi@39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_rgb>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+ };
};
&extal_clk {
@@ -296,61 +371,9 @@
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-hdmi";
- status = "okay";
clock-frequency = <400000>;
-
- ak4642: codec@12 {
- compatible = "asahi-kasei,ak4642";
- #sound-dai-cells = <0>;
- reg = <0x12>;
- };
-
- composite-in@20 {
- compatible = "adi,adv7180";
- reg = <0x20>;
- remote = <&vin0>;
-
- port {
- adv7180: endpoint {
- bus-width = <8>;
- remote-endpoint = <&vin0ep>;
- };
- };
- };
-
- hdmi@39 {
- compatible = "adi,adv7511w";
- reg = <0x39>;
- interrupt-parent = <&gpio3>;
- interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&du_out_rgb>;
- };
- };
-
- port@1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
};
&sata0 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 08/13] ARM: dts: porter: use demuxer for I2C2
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New patch
* Compile tested only
---
arch/arm/boot/dts/r8a7791-porter.dts | 129 +++++++++++++++++++++--------------
1 file changed, 76 insertions(+), 53 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts
index 6761d11d3f9e..dea3c1a103a5 100644
--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/r8a7791-porter.dts
@@ -29,6 +29,8 @@
aliases {
serial0 = &scif0;
+ i2c9 = "gpioi2c2";
+ i2c10 = "i2chdmi";
};
chosen {
@@ -135,6 +137,79 @@
clocks = <&x14_clk>;
};
};
+
+ gpioi2c2: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio2 7 GPIO_ACTIVE_HIGH /* sda */
+ &gpio2 6 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
+ /*
+ * A fallback to GPIO is provided for I2C2.
+ */
+ i2chdmi: i2c-10 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c2>, <&gpioi2c2>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ak4642: codec at 12 {
+ compatible = "asahi-kasei,ak4642";
+ #sound-dai-cells = <0>;
+ reg = <0x12>;
+ };
+
+ composite-in at 20 {
+ compatible = "adi,adv7180";
+ reg = <0x20>;
+ remote = <&vin0>;
+
+ port {
+ adv7180: endpoint {
+ bus-width = <8>;
+ remote-endpoint = <&vin0ep>;
+ };
+ };
+ };
+
+ hdmi at 39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_rgb>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+ };
};
&extal_clk {
@@ -296,61 +371,9 @@
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-hdmi";
- status = "okay";
clock-frequency = <400000>;
-
- ak4642: codec at 12 {
- compatible = "asahi-kasei,ak4642";
- #sound-dai-cells = <0>;
- reg = <0x12>;
- };
-
- composite-in at 20 {
- compatible = "adi,adv7180";
- reg = <0x20>;
- remote = <&vin0>;
-
- port {
- adv7180: endpoint {
- bus-width = <8>;
- remote-endpoint = <&vin0ep>;
- };
- };
- };
-
- hdmi at 39 {
- compatible = "adi,adv7511w";
- reg = <0x39>;
- interrupt-parent = <&gpio3>;
- interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&du_out_rgb>;
- };
- };
-
- port at 1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
};
&sata0 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 09/13] ARM: dts: porter: use demuxer for I2C2
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New patch
---
arch/arm/boot/dts/r8a7793-gose.dts | 114 ++++++++++++++++++++++---------------
1 file changed, 69 insertions(+), 45 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index 90af18600124..2c8c8a4852c8 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -48,6 +48,8 @@
aliases {
serial0 = &scif0;
serial1 = &scif1;
+ i2c9 = "gpioi2c2";
+ i2c11 = "i2chdmi";
};
chosen {
@@ -275,6 +277,72 @@
#clock-cells = <0>;
clock-frequency = <148500000>;
};
+
+ gpioi2c2: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio2 7 GPIO_ACTIVE_HIGH /* sda */
+ &gpio2 6 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
+ /*
+ * A fallback to GPIO is provided for I2C2.
+ */
+ i2chdmi: i2c-11 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c2>, <&gpioi2c2>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ak4643: codec@12 {
+ compatible = "asahi-kasei,ak4643";
+ #sound-dai-cells = <0>;
+ reg = <0x12>;
+ };
+
+ hdmi@39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_rgb>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+
+ eeprom@50 {
+ compatible = "renesas,r1ex24002", "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+ };
};
&du {
@@ -488,54 +556,10 @@
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-hdmi";
status = "okay";
clock-frequency = <100000>;
-
- ak4643: codec@12 {
- compatible = "asahi-kasei,ak4643";
- #sound-dai-cells = <0>;
- reg = <0x12>;
- };
-
- hdmi@39 {
- compatible = "adi,adv7511w";
- reg = <0x39>;
- interrupt-parent = <&gpio3>;
- interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&du_out_rgb>;
- };
- };
-
- port@1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
-
- eeprom@50 {
- compatible = "renesas,r1ex24002", "atmel,24c02";
- reg = <0x50>;
- pagesize = <16>;
- };
};
&rcar_sound {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 09/13] ARM: dts: porter: use demuxer for I2C2
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New patch
---
arch/arm/boot/dts/r8a7793-gose.dts | 114 ++++++++++++++++++++++---------------
1 file changed, 69 insertions(+), 45 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index 90af18600124..2c8c8a4852c8 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -48,6 +48,8 @@
aliases {
serial0 = &scif0;
serial1 = &scif1;
+ i2c9 = "gpioi2c2";
+ i2c11 = "i2chdmi";
};
chosen {
@@ -275,6 +277,72 @@
#clock-cells = <0>;
clock-frequency = <148500000>;
};
+
+ gpioi2c2: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio2 7 GPIO_ACTIVE_HIGH /* sda */
+ &gpio2 6 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
+ /*
+ * A fallback to GPIO is provided for I2C2.
+ */
+ i2chdmi: i2c-11 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c2>, <&gpioi2c2>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ak4643: codec at 12 {
+ compatible = "asahi-kasei,ak4643";
+ #sound-dai-cells = <0>;
+ reg = <0x12>;
+ };
+
+ hdmi at 39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_rgb>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+
+ eeprom at 50 {
+ compatible = "renesas,r1ex24002", "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+ };
};
&du {
@@ -488,54 +556,10 @@
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-hdmi";
status = "okay";
clock-frequency = <100000>;
-
- ak4643: codec at 12 {
- compatible = "asahi-kasei,ak4643";
- #sound-dai-cells = <0>;
- reg = <0x12>;
- };
-
- hdmi at 39 {
- compatible = "adi,adv7511w";
- reg = <0x39>;
- interrupt-parent = <&gpio3>;
- interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&du_out_rgb>;
- };
- };
-
- port at 1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
-
- eeprom at 50 {
- compatible = "renesas,r1ex24002", "atmel,24c02";
- reg = <0x50>;
- pagesize = <16>;
- };
};
&rcar_sound {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 10/13] ARM: dts: koelsch: use demuxer for I2C4
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Make it possible to fallback to GPIO for I2C4 on the EXIO-E connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New Patch
---
arch/arm/boot/dts/r8a7793-gose.dts | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index 2c8c8a4852c8..0e418e7a6d5c 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -49,7 +49,9 @@
serial0 = &scif0;
serial1 = &scif1;
i2c9 = "gpioi2c2";
+ i2c10 = "gpioi2c4";
i2c11 = "i2chdmi";
+ i2c12 = "i2cexio4";
};
chosen {
@@ -289,6 +291,17 @@
i2c-gpio,delay-us = <5>;
};
+ gpioi2c4: i2c-10 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio7 14 GPIO_ACTIVE_HIGH /* sda */
+ &gpio7 13 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* A fallback to GPIO is provided for I2C2.
*/
@@ -343,6 +356,18 @@
pagesize = <16>;
};
};
+
+ /*
+ * I2C4 is routed to EXIO connector E, pins 37 (SCL) + 39 (SDA).
+ * A fallback to GPIO is provided.
+ */
+ i2cexio4: i2c-12 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c4>, <&gpioi2c4>;
+ i2c-bus-name = "i2c-exio4";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
&du {
@@ -383,6 +408,11 @@
function = "i2c2";
};
+ i2c4_pins: i2c4 {
+ groups = "i2c4";
+ function = "i2c4";
+ };
+
du_pins: du {
groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
function = "du";
@@ -562,6 +592,11 @@
clock-frequency = <100000>;
};
+&i2c4 {
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "i2c-exio4";
+};
+
&rcar_sound {
pinctrl-0 = <&sound_pins &sound_clk_pins>;
pinctrl-names = "default";
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 10/13] ARM: dts: koelsch: use demuxer for I2C4
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Make it possible to fallback to GPIO for I2C4 on the EXIO-E connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New Patch
---
arch/arm/boot/dts/r8a7793-gose.dts | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index 2c8c8a4852c8..0e418e7a6d5c 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -49,7 +49,9 @@
serial0 = &scif0;
serial1 = &scif1;
i2c9 = "gpioi2c2";
+ i2c10 = "gpioi2c4";
i2c11 = "i2chdmi";
+ i2c12 = "i2cexio4";
};
chosen {
@@ -289,6 +291,17 @@
i2c-gpio,delay-us = <5>;
};
+ gpioi2c4: i2c-10 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio7 14 GPIO_ACTIVE_HIGH /* sda */
+ &gpio7 13 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* A fallback to GPIO is provided for I2C2.
*/
@@ -343,6 +356,18 @@
pagesize = <16>;
};
};
+
+ /*
+ * I2C4 is routed to EXIO connector E, pins 37 (SCL) + 39 (SDA).
+ * A fallback to GPIO is provided.
+ */
+ i2cexio4: i2c-12 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c4>, <&gpioi2c4>;
+ i2c-bus-name = "i2c-exio4";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
&du {
@@ -383,6 +408,11 @@
function = "i2c2";
};
+ i2c4_pins: i2c4 {
+ groups = "i2c4";
+ function = "i2c4";
+ };
+
du_pins: du {
groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
function = "du";
@@ -562,6 +592,11 @@
clock-frequency = <100000>;
};
+&i2c4 {
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "i2c-exio4";
+};
+
&rcar_sound {
pinctrl-0 = <&sound_pins &sound_clk_pins>;
pinctrl-names = "default";
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 11/13] ARM: dts: alt: use demuxer for I2C1
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Create a separate bus for HDMI related I2C1 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New patch
---
arch/arm/boot/dts/r8a7794-alt.dts | 54 ++++++++++++++++++++++++++++-----------
1 file changed, 39 insertions(+), 15 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts
index 1ad37d431a2a..d00b1b33f6ed 100644
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/r8a7794-alt.dts
@@ -10,6 +10,7 @@
/dts-v1/;
#include "r8a7794.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "Alt";
@@ -17,6 +18,8 @@
aliases {
serial0 = &scif2;
+ i2c9 = "gpioi2c1";
+ i2c11 = "i2chdmi";
};
chosen {
@@ -77,6 +80,41 @@
#clock-cells = <0>;
clock-frequency = <148500000>;
};
+
+ gpioi2c1: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio4 1 GPIO_ACTIVE_HIGH /* sda */
+ &gpio4 0 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
+ /*
+ * A fallback to GPIO is provided for I2C1.
+ */
+ i2chdmi: i2c-11 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c1>, <&gpioi2c1>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ composite-in@20 {
+ compatible = "adi,adv7180";
+ reg = <0x20>;
+ remote = <&vin0>;
+
+ port {
+ adv7180: endpoint {
+ bus-width = <8>;
+ remote-endpoint = <&vin0ep>;
+ };
+ };
+ };
+ };
};
&du {
@@ -171,23 +209,9 @@
&i2c1 {
pinctrl-0 = <&i2c1_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-hdmi";
- status = "okay";
clock-frequency = <400000>;
-
- composite-in@20 {
- compatible = "adi,adv7180";
- reg = <0x20>;
- remote = <&vin0>;
-
- port {
- adv7180: endpoint {
- bus-width = <8>;
- remote-endpoint = <&vin0ep>;
- };
- };
- };
};
&vin0 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 11/13] ARM: dts: alt: use demuxer for I2C1
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Create a separate bus for HDMI related I2C1 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New patch
---
arch/arm/boot/dts/r8a7794-alt.dts | 54 ++++++++++++++++++++++++++++-----------
1 file changed, 39 insertions(+), 15 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts
index 1ad37d431a2a..d00b1b33f6ed 100644
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/r8a7794-alt.dts
@@ -10,6 +10,7 @@
/dts-v1/;
#include "r8a7794.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "Alt";
@@ -17,6 +18,8 @@
aliases {
serial0 = &scif2;
+ i2c9 = "gpioi2c1";
+ i2c11 = "i2chdmi";
};
chosen {
@@ -77,6 +80,41 @@
#clock-cells = <0>;
clock-frequency = <148500000>;
};
+
+ gpioi2c1: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio4 1 GPIO_ACTIVE_HIGH /* sda */
+ &gpio4 0 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
+ /*
+ * A fallback to GPIO is provided for I2C1.
+ */
+ i2chdmi: i2c-11 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c1>, <&gpioi2c1>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ composite-in at 20 {
+ compatible = "adi,adv7180";
+ reg = <0x20>;
+ remote = <&vin0>;
+
+ port {
+ adv7180: endpoint {
+ bus-width = <8>;
+ remote-endpoint = <&vin0ep>;
+ };
+ };
+ };
+ };
};
&du {
@@ -171,23 +209,9 @@
&i2c1 {
pinctrl-0 = <&i2c1_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-hdmi";
- status = "okay";
clock-frequency = <400000>;
-
- composite-in at 20 {
- compatible = "adi,adv7180";
- reg = <0x20>;
- remote = <&vin0>;
-
- port {
- adv7180: endpoint {
- bus-width = <8>;
- remote-endpoint = <&vin0ep>;
- };
- };
- };
};
&vin0 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 12/13] ARM: dts: alt: use demuxer for I2C4
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Make it possible to fallback to GPIO for I2C4 on the EXIO-B connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New Patch
---
arch/arm/boot/dts/r8a7794-alt.dts | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts
index d00b1b33f6ed..10f72e700685 100644
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/r8a7794-alt.dts
@@ -19,7 +19,9 @@
aliases {
serial0 = &scif2;
i2c9 = "gpioi2c1";
+ i2c10 = "gpioi2c4";
i2c11 = "i2chdmi";
+ i2c12 = "i2cexio4";
};
chosen {
@@ -92,6 +94,17 @@
i2c-gpio,delay-us = <5>;
};
+ gpioi2c4: i2c-10 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio4 9 GPIO_ACTIVE_HIGH /* sda */
+ &gpio4 8 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* A fallback to GPIO is provided for I2C1.
*/
@@ -115,6 +128,18 @@
};
};
};
+
+ /*
+ * I2C4 is routed to EXIO connector B, pins 73 (SCL) + 74 (SDA).
+ * A fallback to GPIO is provided.
+ */
+ i2cexio4: i2c-14 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c4>, <&gpioi2c4>;
+ i2c-bus-name = "i2c-exio4";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
&du {
@@ -174,6 +199,11 @@
function = "i2c1";
};
+ i2c4_pins: i2c4 {
+ groups = "i2c4";
+ function = "i2c4";
+ };
+
vin0_pins: vin0 {
groups = "vin0_data8", "vin0_clk";
function = "vin0";
@@ -214,6 +244,11 @@
clock-frequency = <400000>;
};
+&i2c4 {
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "i2c-exio4";
+};
+
&vin0 {
status = "okay";
pinctrl-0 = <&vin0_pins>;
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 12/13] ARM: dts: alt: use demuxer for I2C4
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Make it possible to fallback to GPIO for I2C4 on the EXIO-B connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New Patch
---
arch/arm/boot/dts/r8a7794-alt.dts | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts
index d00b1b33f6ed..10f72e700685 100644
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/r8a7794-alt.dts
@@ -19,7 +19,9 @@
aliases {
serial0 = &scif2;
i2c9 = "gpioi2c1";
+ i2c10 = "gpioi2c4";
i2c11 = "i2chdmi";
+ i2c12 = "i2cexio4";
};
chosen {
@@ -92,6 +94,17 @@
i2c-gpio,delay-us = <5>;
};
+ gpioi2c4: i2c-10 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio4 9 GPIO_ACTIVE_HIGH /* sda */
+ &gpio4 8 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
/*
* A fallback to GPIO is provided for I2C1.
*/
@@ -115,6 +128,18 @@
};
};
};
+
+ /*
+ * I2C4 is routed to EXIO connector B, pins 73 (SCL) + 74 (SDA).
+ * A fallback to GPIO is provided.
+ */
+ i2cexio4: i2c-14 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c4>, <&gpioi2c4>;
+ i2c-bus-name = "i2c-exio4";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
&du {
@@ -174,6 +199,11 @@
function = "i2c1";
};
+ i2c4_pins: i2c4 {
+ groups = "i2c4";
+ function = "i2c4";
+ };
+
vin0_pins: vin0 {
groups = "vin0_data8", "vin0_clk";
function = "vin0";
@@ -214,6 +244,11 @@
clock-frequency = <400000>;
};
+&i2c4 {
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "i2c-exio4";
+};
+
&vin0 {
status = "okay";
pinctrl-0 = <&vin0_pins>;
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 13/13] ARM: dts: silk: use demuxer for I2C1
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 3:43 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-renesas-soc
Cc: linux-arm-kernel, Magnus Damm, Wolfram Sang, Simon Horman
Create a separate bus for HDMI related I2C1 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New patch
* Compile tested only
---
arch/arm/boot/dts/r8a7794-silk.dts | 117 ++++++++++++++++++++++---------------
1 file changed, 70 insertions(+), 47 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts
index cf24f45fff22..b1beb22cb980 100644
--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/r8a7794-silk.dts
@@ -20,6 +20,8 @@
aliases {
serial0 = &scif2;
+ i2c9 = "gpioi2c1";
+ i2c10 = "i2chdmi";
};
chosen {
@@ -119,6 +121,73 @@
#clock-cells = <0>;
clock-frequency = <74250000>;
};
+
+ gpioi2c1: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio4 1 GPIO_ACTIVE_HIGH /* sda */
+ &gpio4 0 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
+ /*
+ * A fallback to GPIO is provided for I2C1.
+ */
+ i2chdmi: i2c-10 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c1>, <&gpioi2c1>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ composite-in@20 {
+ compatible = "adi,adv7180";
+ reg = <0x20>;
+ remote = <&vin0>;
+
+ port {
+ adv7180: endpoint {
+ bus-width = <8>;
+ remote-endpoint = <&vin0ep>;
+ };
+ };
+ };
+
+ hdmi@39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_rgb0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+ };
};
&extal_clk {
@@ -225,55 +294,9 @@
&i2c1 {
pinctrl-0 = <&i2c1_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-hdmi";
- status = "okay";
clock-frequency = <400000>;
-
- composite-in@20 {
- compatible = "adi,adv7180";
- reg = <0x20>;
- remote = <&vin0>;
-
- port {
- adv7180: endpoint {
- bus-width = <8>;
- remote-endpoint = <&vin0ep>;
- };
- };
- };
-
- hdmi@39 {
- compatible = "adi,adv7511w";
- reg = <0x39>;
- interrupt-parent = <&gpio5>;
- interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&du_out_rgb0>;
- };
- };
-
- port@1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
};
&mmcif0 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v3 13/13] ARM: dts: silk: use demuxer for I2C1
@ 2016-06-22 3:43 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-06-22 3:43 UTC (permalink / raw)
To: linux-arm-kernel
Create a separate bus for HDMI related I2C1 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* New patch
* Compile tested only
---
arch/arm/boot/dts/r8a7794-silk.dts | 117 ++++++++++++++++++++++---------------
1 file changed, 70 insertions(+), 47 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts
index cf24f45fff22..b1beb22cb980 100644
--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/r8a7794-silk.dts
@@ -20,6 +20,8 @@
aliases {
serial0 = &scif2;
+ i2c9 = "gpioi2c1";
+ i2c10 = "i2chdmi";
};
chosen {
@@ -119,6 +121,73 @@
#clock-cells = <0>;
clock-frequency = <74250000>;
};
+
+ gpioi2c1: i2c-9 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "i2c-gpio";
+ status = "disabled";
+ gpios = <&gpio4 1 GPIO_ACTIVE_HIGH /* sda */
+ &gpio4 0 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <5>;
+ };
+
+ /*
+ * A fallback to GPIO is provided for I2C1.
+ */
+ i2chdmi: i2c-10 {
+ compatible = "i2c-demux-pinctrl";
+ i2c-parent = <&i2c1>, <&gpioi2c1>;
+ i2c-bus-name = "i2c-hdmi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ composite-in at 20 {
+ compatible = "adi,adv7180";
+ reg = <0x20>;
+ remote = <&vin0>;
+
+ port {
+ adv7180: endpoint {
+ bus-width = <8>;
+ remote-endpoint = <&vin0ep>;
+ };
+ };
+ };
+
+ hdmi at 39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_rgb0>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+ };
};
&extal_clk {
@@ -225,55 +294,9 @@
&i2c1 {
pinctrl-0 = <&i2c1_pins>;
- pinctrl-names = "default";
+ pinctrl-names = "i2c-hdmi";
- status = "okay";
clock-frequency = <400000>;
-
- composite-in at 20 {
- compatible = "adi,adv7180";
- reg = <0x20>;
- remote = <&vin0>;
-
- port {
- adv7180: endpoint {
- bus-width = <8>;
- remote-endpoint = <&vin0ep>;
- };
- };
- };
-
- hdmi at 39 {
- compatible = "adi,adv7511w";
- reg = <0x39>;
- interrupt-parent = <&gpio5>;
- interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&du_out_rgb0>;
- };
- };
-
- port at 1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
};
&mmcif0 {
--
2.1.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* Re: [PATCH v3 04/13] ARM: dts: lager: use demuxer for IIC3/I2C3
2016-06-22 3:43 ` Simon Horman
@ 2016-06-22 7:29 ` Geert Uytterhoeven
-1 siblings, 0 replies; 34+ messages in thread
From: Geert Uytterhoeven @ 2016-06-22 7:29 UTC (permalink / raw)
To: Simon Horman
Cc: linux-renesas-soc, Wolfram Sang, Magnus Damm, linux-arm-kernel
On Wed, Jun 22, 2016 at 5:43 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Create a separate bus for dla98063 PMIC and da9210 regulator
da9063.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 34+ messages in thread
* [PATCH v3 04/13] ARM: dts: lager: use demuxer for IIC3/I2C3
@ 2016-06-22 7:29 ` Geert Uytterhoeven
0 siblings, 0 replies; 34+ messages in thread
From: Geert Uytterhoeven @ 2016-06-22 7:29 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Jun 22, 2016 at 5:43 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Create a separate bus for dla98063 PMIC and da9210 regulator
da9063.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v3 01/13] ARM: dts: lager: rename and reindex i2cexio
2016-06-22 3:43 ` Simon Horman
@ 2016-08-30 15:29 ` Wolfram Sang
-1 siblings, 0 replies; 34+ messages in thread
From: Wolfram Sang @ 2016-08-30 15:29 UTC (permalink / raw)
To: Simon Horman
Cc: linux-renesas-soc, linux-arm-kernel, Magnus Damm, Wolfram Sang
[-- Attachment #1: Type: text/plain, Size: 297 bytes --]
Hi Simon,
> serial0 = &scif0;
> serial1 = &scifa1;
> - i2c8 = "i2cexio";
> + i2c10 = "i2cexio0";
Those should be pointers, i.e. "&i2cexio0;", here and in the rest of
your series. Sorry for the broken template! Did you have a chance to
test my fix for the demuxer?
Regards,
Wolfram
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 34+ messages in thread
* [PATCH v3 01/13] ARM: dts: lager: rename and reindex i2cexio
@ 2016-08-30 15:29 ` Wolfram Sang
0 siblings, 0 replies; 34+ messages in thread
From: Wolfram Sang @ 2016-08-30 15:29 UTC (permalink / raw)
To: linux-arm-kernel
Hi Simon,
> serial0 = &scif0;
> serial1 = &scifa1;
> - i2c8 = "i2cexio";
> + i2c10 = "i2cexio0";
Those should be pointers, i.e. "&i2cexio0;", here and in the rest of
your series. Sorry for the broken template! Did you have a chance to
test my fix for the demuxer?
Regards,
Wolfram
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160830/6e38476e/attachment.sig>
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v3 01/13] ARM: dts: lager: rename and reindex i2cexio
2016-08-30 15:29 ` Wolfram Sang
@ 2016-09-02 8:17 ` Simon Horman
-1 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-09-02 8:17 UTC (permalink / raw)
To: Wolfram Sang
Cc: linux-renesas-soc, linux-arm-kernel, Magnus Damm, Wolfram Sang
On Tue, Aug 30, 2016 at 05:29:08PM +0200, Wolfram Sang wrote:
> Hi Simon,
>
> > serial0 = &scif0;
> > serial1 = &scifa1;
> > - i2c8 = "i2cexio";
> > + i2c10 = "i2cexio0";
>
> Those should be pointers, i.e. "&i2cexio0;", here and in the rest of
> your series. Sorry for the broken template!
Thanks, got it.
> Did you have a chance to
> test my fix for the demuxer?
Sorry, not yet.
^ permalink raw reply [flat|nested] 34+ messages in thread
* [PATCH v3 01/13] ARM: dts: lager: rename and reindex i2cexio
@ 2016-09-02 8:17 ` Simon Horman
0 siblings, 0 replies; 34+ messages in thread
From: Simon Horman @ 2016-09-02 8:17 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Aug 30, 2016 at 05:29:08PM +0200, Wolfram Sang wrote:
> Hi Simon,
>
> > serial0 = &scif0;
> > serial1 = &scifa1;
> > - i2c8 = "i2cexio";
> > + i2c10 = "i2cexio0";
>
> Those should be pointers, i.e. "&i2cexio0;", here and in the rest of
> your series. Sorry for the broken template!
Thanks, got it.
> Did you have a chance to
> test my fix for the demuxer?
Sorry, not yet.
^ permalink raw reply [flat|nested] 34+ messages in thread
end of thread, other threads:[~2016-09-02 8:18 UTC | newest]
Thread overview: 34+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-06-22 3:43 [PATCH v3 00/13] ARM: dts: r8a779x: use demuxer for I2C Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 01/13] ARM: dts: lager: rename and reindex i2cexio Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-08-30 15:29 ` Wolfram Sang
2016-08-30 15:29 ` Wolfram Sang
2016-09-02 8:17 ` Simon Horman
2016-09-02 8:17 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 02/13] ARM: dts: lager: use demuxer for IIC1/I2C1 Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 03/13] ARM: dts: lager: use demuxer for IIC2/I2C2 Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 04/13] ARM: dts: lager: use demuxer for IIC3/I2C3 Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 7:29 ` Geert Uytterhoeven
2016-06-22 7:29 ` Geert Uytterhoeven
2016-06-22 3:43 ` [PATCH v3 05/13] ARM: dts: koelsch: use demuxer for I2C1 Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 06/13] ARM: dts: koelsch: use demuxer for I2C2 Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 07/13] ARM: dts: koelsch: use demuxer for I2C4 Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 08/13] ARM: dts: porter: use demuxer for I2C2 Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 09/13] " Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 10/13] ARM: dts: koelsch: use demuxer for I2C4 Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 11/13] ARM: dts: alt: use demuxer for I2C1 Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 12/13] ARM: dts: alt: use demuxer for I2C4 Simon Horman
2016-06-22 3:43 ` Simon Horman
2016-06-22 3:43 ` [PATCH v3 13/13] ARM: dts: silk: use demuxer for I2C1 Simon Horman
2016-06-22 3:43 ` Simon Horman
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.