* [PATCH v5 0/4] arm64: renesas: enable H3ULCB board peripherals @ 2016-09-02 16:23 ` Vladimir Barinov 0 siblings, 0 replies; 20+ messages in thread From: Vladimir Barinov @ 2016-09-02 16:23 UTC (permalink / raw) To: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA, Vladimir Barinov Hello, This adds the folowing: - R8A7795 SoC based H3ULCB board peripherals Vladimir Barinov (4): [1/4] arm64: dts: h3ulcb: enable GPIO leds [2/4] arm64: dts: h3ulcb: enable GPIO keys [3/4] arm64: dts: h3ulcb: enable SDHI0 [4/4] arm64: dts: h3ulcb: Sound SSI support --- This patchset is against the 'kernel/git/horms/renesas.git' repo. arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 189 +++++++++++++++++++++++++ 1 file changed, 189 insertions(+) -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v5 0/4] arm64: renesas: enable H3ULCB board peripherals @ 2016-09-02 16:23 ` Vladimir Barinov 0 siblings, 0 replies; 20+ messages in thread From: Vladimir Barinov @ 2016-09-02 16:23 UTC (permalink / raw) To: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland Cc: devicetree, linux-renesas-soc, Vladimir Barinov Hello, This adds the folowing: - R8A7795 SoC based H3ULCB board peripherals Vladimir Barinov (4): [1/4] arm64: dts: h3ulcb: enable GPIO leds [2/4] arm64: dts: h3ulcb: enable GPIO keys [3/4] arm64: dts: h3ulcb: enable SDHI0 [4/4] arm64: dts: h3ulcb: Sound SSI support --- This patchset is against the 'kernel/git/horms/renesas.git' repo. arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 189 +++++++++++++++++++++++++ 1 file changed, 189 insertions(+) ^ permalink raw reply [flat|nested] 20+ messages in thread
[parent not found: <1472833419-26139-1-git-send-email-vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org>]
* [PATCH v5 1/4] arm64: dts: h3ulcb: enable GPIO leds 2016-09-02 16:23 ` Vladimir Barinov @ 2016-09-02 16:24 ` Vladimir Barinov -1 siblings, 0 replies; 20+ messages in thread From: Vladimir Barinov @ 2016-09-02 16:24 UTC (permalink / raw) To: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA, Vladimir Barinov This supports GPIO leds on H3ULCB board Signed-off-by: Vladimir Barinov <vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org> Reviewed-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org> --- Changes in version 3: - initially added Changes in version 4: - removed led4 in favor of gpio-keys - added label Changes in version 5: - nothing arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts index fb694b8..3329f78 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts +++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts @@ -31,6 +31,19 @@ /* first 128MB is reserved for secure area. */ reg = <0x0 0x48000000 0x0 0x38000000>; }; + + leds { + compatible = "gpio-leds"; + + led5 { + label = "LED5"; + gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>; + }; + led6 { + label = "LED6"; + gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; + }; + }; }; &extal_clk { -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 1/4] arm64: dts: h3ulcb: enable GPIO leds @ 2016-09-02 16:24 ` Vladimir Barinov 0 siblings, 0 replies; 20+ messages in thread From: Vladimir Barinov @ 2016-09-02 16:24 UTC (permalink / raw) To: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland Cc: devicetree, linux-renesas-soc, Vladimir Barinov This supports GPIO leds on H3ULCB board Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> --- Changes in version 3: - initially added Changes in version 4: - removed led4 in favor of gpio-keys - added label Changes in version 5: - nothing arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts index fb694b8..3329f78 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts +++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts @@ -31,6 +31,19 @@ /* first 128MB is reserved for secure area. */ reg = <0x0 0x48000000 0x0 0x38000000>; }; + + leds { + compatible = "gpio-leds"; + + led5 { + label = "LED5"; + gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>; + }; + led6 { + label = "LED6"; + gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; + }; + }; }; &extal_clk { -- 1.9.1 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH v5 1/4] arm64: dts: h3ulcb: enable GPIO leds 2016-09-02 16:24 ` Vladimir Barinov (?) @ 2016-09-05 12:26 ` Simon Horman -1 siblings, 0 replies; 20+ messages in thread From: Simon Horman @ 2016-09-05 12:26 UTC (permalink / raw) To: Vladimir Barinov Cc: Magnus Damm, Rob Herring, Mark Rutland, devicetree, linux-renesas-soc On Fri, Sep 02, 2016 at 07:24:48PM +0300, Vladimir Barinov wrote: > This supports GPIO leds on H3ULCB board > > Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> > Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> > --- > Changes in version 3: > - initially added > Changes in version 4: > - removed led4 in favor of gpio-keys > - added label > Changes in version 5: > - nothing > > arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 13 +++++++++++++ > 1 file changed, 13 insertions(+) > > diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts > index fb694b8..3329f78 100644 > --- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts > +++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts > @@ -31,6 +31,19 @@ > /* first 128MB is reserved for secure area. */ > reg = <0x0 0x48000000 0x0 0x38000000>; > }; > + > + leds { > + compatible = "gpio-leds"; > + > + led5 { > + label = "LED5"; > + gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>; > + }; > + led6 { > + label = "LED6"; > + gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; > + }; > + }; > }; Please remove the label properties. ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v5 2/4] arm64: dts: h3ulcb: enable GPIO keys 2016-09-02 16:23 ` Vladimir Barinov @ 2016-09-02 16:24 ` Vladimir Barinov -1 siblings, 0 replies; 20+ messages in thread From: Vladimir Barinov @ 2016-09-02 16:24 UTC (permalink / raw) To: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA, Vladimir Barinov This supports GPIO keys on H3ULCB board Signed-off-by: Vladimir Barinov <vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org> --- Changes in version 4: - initially added Changes in version 5: - nothing arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 14 +++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts index fb694b8..3329f78 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts +++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts @@ -12,6 +12,7 @@ /dts-v1/; #include "r8a7795.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> / { model = "Renesas H3ULCB board based on r8a7795"; @@ -31,6 +31,18 @@ /* first 128MB is reserved for secure area. */ reg = <0x0 0x48000000 0x0 0x38000000>; }; + + keyboard { + compatible = "gpio-keys"; + + key-1 { + linux,code = <KEY_1>; + label = "SW3"; + wakeup-source; + debounce-interval = <20>; + gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; + }; + }; leds { compatible = "gpio-leds"; -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 2/4] arm64: dts: h3ulcb: enable GPIO keys @ 2016-09-02 16:24 ` Vladimir Barinov 0 siblings, 0 replies; 20+ messages in thread From: Vladimir Barinov @ 2016-09-02 16:24 UTC (permalink / raw) To: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland Cc: devicetree, linux-renesas-soc, Vladimir Barinov This supports GPIO keys on H3ULCB board Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> --- Changes in version 4: - initially added Changes in version 5: - nothing arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 14 +++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts index fb694b8..3329f78 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts +++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts @@ -12,6 +12,7 @@ /dts-v1/; #include "r8a7795.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> / { model = "Renesas H3ULCB board based on r8a7795"; @@ -31,6 +31,18 @@ /* first 128MB is reserved for secure area. */ reg = <0x0 0x48000000 0x0 0x38000000>; }; + + keyboard { + compatible = "gpio-keys"; + + key-1 { + linux,code = <KEY_1>; + label = "SW3"; + wakeup-source; + debounce-interval = <20>; + gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; + }; + }; leds { compatible = "gpio-leds"; -- 1.9.1 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH v5 2/4] arm64: dts: h3ulcb: enable GPIO keys 2016-09-02 16:24 ` Vladimir Barinov (?) @ 2016-09-05 7:57 ` Geert Uytterhoeven [not found] ` <CAMuHMdWXq8enfSUcwFK=6NXoZgJkqo=iScjO8A3ZO-sGrcxb4w-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org> -1 siblings, 1 reply; 20+ messages in thread From: Geert Uytterhoeven @ 2016-09-05 7:57 UTC (permalink / raw) To: Vladimir Barinov Cc: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland, devicetree, Linux-Renesas On Fri, Sep 2, 2016 at 6:24 PM, Vladimir Barinov <vladimir.barinov@cogentembedded.com> wrote: > This supports GPIO keys on H3ULCB board > > Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds ^ permalink raw reply [flat|nested] 20+ messages in thread
[parent not found: <CAMuHMdWXq8enfSUcwFK=6NXoZgJkqo=iScjO8A3ZO-sGrcxb4w-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>]
* Re: [PATCH v5 2/4] arm64: dts: h3ulcb: enable GPIO keys 2016-09-05 7:57 ` Geert Uytterhoeven @ 2016-09-05 12:17 ` Simon Horman 0 siblings, 0 replies; 20+ messages in thread From: Simon Horman @ 2016-09-05 12:17 UTC (permalink / raw) To: Geert Uytterhoeven Cc: Vladimir Barinov, Magnus Damm, Rob Herring, Mark Rutland, devicetree-u79uwXL29TY76Z2rM5mHXA, Linux-Renesas On Mon, Sep 05, 2016 at 09:57:21AM +0200, Geert Uytterhoeven wrote: > On Fri, Sep 2, 2016 at 6:24 PM, Vladimir Barinov > <vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org> wrote: > > This supports GPIO keys on H3ULCB board > > > > Signed-off-by: Vladimir Barinov <vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org> > > Reviewed-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org> Thanks, I have queued this up. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v5 2/4] arm64: dts: h3ulcb: enable GPIO keys @ 2016-09-05 12:17 ` Simon Horman 0 siblings, 0 replies; 20+ messages in thread From: Simon Horman @ 2016-09-05 12:17 UTC (permalink / raw) To: Geert Uytterhoeven Cc: Vladimir Barinov, Magnus Damm, Rob Herring, Mark Rutland, devicetree, Linux-Renesas On Mon, Sep 05, 2016 at 09:57:21AM +0200, Geert Uytterhoeven wrote: > On Fri, Sep 2, 2016 at 6:24 PM, Vladimir Barinov > <vladimir.barinov@cogentembedded.com> wrote: > > This supports GPIO keys on H3ULCB board > > > > Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> > > Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Thanks, I have queued this up. ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v5 3/4] arm64: dts: h3ulcb: enable SDHI0 2016-09-02 16:23 ` Vladimir Barinov @ 2016-09-02 16:25 ` Vladimir Barinov -1 siblings, 0 replies; 20+ messages in thread From: Vladimir Barinov @ 2016-09-02 16:25 UTC (permalink / raw) To: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA, Vladimir Barinov This supports SDHI0 on H3ULCB board SD card slot Signed-off-by: Vladimir Barinov <vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org> Reviewed-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org> --- Changes in version 3: - initially added Changes in version 4: - added sd-uhs-sdr50 Changes in version 5: - nothing --- arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 49 ++++++++++++++++++++++++++ 1 file changed, 49 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts index 6842597..babe41c 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts +++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts @@ -44,6 +44,30 @@ gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; }; }; + + vcc_sdhi0: regulator-vcc-sdhi0 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI0 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vccq_sdhi0: regulator-vccq-sdhi0 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI0 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; + gpios-states = <1>; + states = <3300000 1 + 1800000 0>; + }; }; &extal_clk { @@ -78,6 +102,18 @@ function = "avb"; }; + sdhi0_pins_3v3: sd0_3v3 { + groups = "sdhi0_data4", "sdhi0_ctrl"; + function = "sdhi0"; + power-source = <3300>; + }; + + sdhi0_pins_1v8: sd0_1v8 { + groups = "sdhi0_data4", "sdhi0_ctrl"; + function = "sdhi0"; + power-source = <1800>; + }; + usb1_pins: usb1 { groups = "usb1"; function = "usb1"; @@ -108,6 +144,19 @@ status = "okay"; }; +&sdhi0 { + pinctrl-0 = <&sdhi0_pins_3v3>; + pinctrl-1 = <&sdhi0_pins_1v8>; + pinctrl-names = "default", "state_uhs"; + + vmmc-supply = <&vcc_sdhi0>; + vqmmc-supply = <&vccq_sdhi0>; + cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; + bus-width = <4>; + sd-uhs-sdr50; + status = "okay"; +}; + &wdt0 { timeout-sec = <60>; status = "okay"; -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 3/4] arm64: dts: h3ulcb: enable SDHI0 @ 2016-09-02 16:25 ` Vladimir Barinov 0 siblings, 0 replies; 20+ messages in thread From: Vladimir Barinov @ 2016-09-02 16:25 UTC (permalink / raw) To: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland Cc: devicetree, linux-renesas-soc, Vladimir Barinov This supports SDHI0 on H3ULCB board SD card slot Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> --- Changes in version 3: - initially added Changes in version 4: - added sd-uhs-sdr50 Changes in version 5: - nothing --- arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 49 ++++++++++++++++++++++++++ 1 file changed, 49 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts index 6842597..babe41c 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts +++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts @@ -44,6 +44,30 @@ gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; }; }; + + vcc_sdhi0: regulator-vcc-sdhi0 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI0 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vccq_sdhi0: regulator-vccq-sdhi0 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI0 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; + gpios-states = <1>; + states = <3300000 1 + 1800000 0>; + }; }; &extal_clk { @@ -78,6 +102,18 @@ function = "avb"; }; + sdhi0_pins_3v3: sd0_3v3 { + groups = "sdhi0_data4", "sdhi0_ctrl"; + function = "sdhi0"; + power-source = <3300>; + }; + + sdhi0_pins_1v8: sd0_1v8 { + groups = "sdhi0_data4", "sdhi0_ctrl"; + function = "sdhi0"; + power-source = <1800>; + }; + usb1_pins: usb1 { groups = "usb1"; function = "usb1"; @@ -108,6 +144,19 @@ status = "okay"; }; +&sdhi0 { + pinctrl-0 = <&sdhi0_pins_3v3>; + pinctrl-1 = <&sdhi0_pins_1v8>; + pinctrl-names = "default", "state_uhs"; + + vmmc-supply = <&vcc_sdhi0>; + vqmmc-supply = <&vccq_sdhi0>; + cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; + bus-width = <4>; + sd-uhs-sdr50; + status = "okay"; +}; + &wdt0 { timeout-sec = <60>; status = "okay"; -- 1.9.1 ^ permalink raw reply related [flat|nested] 20+ messages in thread
[parent not found: <1472833508-26267-1-git-send-email-vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org>]
* Re: [PATCH v5 3/4] arm64: dts: h3ulcb: enable SDHI0 2016-09-02 16:25 ` Vladimir Barinov @ 2016-09-05 12:25 ` Simon Horman -1 siblings, 0 replies; 20+ messages in thread From: Simon Horman @ 2016-09-05 12:25 UTC (permalink / raw) To: Vladimir Barinov Cc: Magnus Damm, Rob Herring, Mark Rutland, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA On Fri, Sep 02, 2016 at 07:25:08PM +0300, Vladimir Barinov wrote: > This supports SDHI0 on H3ULCB board SD card slot > > Signed-off-by: Vladimir Barinov <vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org> > Reviewed-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org> Thanks, I have queued this up. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v5 3/4] arm64: dts: h3ulcb: enable SDHI0 @ 2016-09-05 12:25 ` Simon Horman 0 siblings, 0 replies; 20+ messages in thread From: Simon Horman @ 2016-09-05 12:25 UTC (permalink / raw) To: Vladimir Barinov Cc: Magnus Damm, Rob Herring, Mark Rutland, devicetree, linux-renesas-soc On Fri, Sep 02, 2016 at 07:25:08PM +0300, Vladimir Barinov wrote: > This supports SDHI0 on H3ULCB board SD card slot > > Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> > Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Thanks, I have queued this up. ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v5 4/4] arm64: dts: h3ulcb: Sound SSI support 2016-09-02 16:23 ` Vladimir Barinov @ 2016-09-02 16:25 ` Vladimir Barinov -1 siblings, 0 replies; 20+ messages in thread From: Vladimir Barinov @ 2016-09-02 16:25 UTC (permalink / raw) To: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA, Vladimir Barinov This supports SSI sound for H3ULCB board. SSI DMA mode used. CS2000 used as AUDIO_CLK_B. Signed-off-by: Vladimir Barinov <vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org> --- Changes in version 3: - initially added Changes in version 4: - added comment for audio_clkout Changes in version 5: - renamed x12_clk node to x12 - renamed clk_multiplier node to clk-multiplier - renamed audio_clkout node to audio-clkout - renamed sound_clk node to sound-clk arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 115 +++++++++++++++++++++++++ 1 file changed, 115 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts index bbd7928..a254231 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts +++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts @@ -45,6 +45,12 @@ }; }; + x12_clk: x12 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24576000>; + }; + vcc_sdhi0: regulator-vcc-sdhi0 { compatible = "regulator-fixed"; @@ -68,6 +74,32 @@ states = <3300000 1 1800000 0>; }; + + audio_clkout: audio-clkout { + /* + * This is same as <&rcar_sound 0> + * but needed to avoid cs2000/rcar_sound probe dead-lock + */ + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <11289600>; + }; + + rsnd_ak4613: sound { + compatible = "simple-audio-card"; + + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcpu>; + simple-audio-card,frame-master = <&sndcpu>; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&ak4613>; + }; + }; }; &extal_clk { @@ -113,6 +141,17 @@ power-source = <1800>; }; + sound_pins: sound { + groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a"; + function = "ssi"; + }; + + sound_clk_pins: sound-clk { + groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a", + "audio_clkout_a", "audio_clkout3_a"; + function = "audio_clk"; + }; + usb1_pins: usb1 { groups = "usb1"; function = "usb1"; @@ -136,6 +176,73 @@ pinctrl-names = "default"; status = "okay"; + + clock-frequency = <100000>; + + ak4613: codec@10 { + compatible = "asahi-kasei,ak4613"; + #sound-dai-cells = <0>; + reg = <0x10>; + clocks = <&rcar_sound 3>; + + asahi-kasei,in1-single-end; + asahi-kasei,in2-single-end; + asahi-kasei,out1-single-end; + asahi-kasei,out2-single-end; + asahi-kasei,out3-single-end; + asahi-kasei,out4-single-end; + asahi-kasei,out5-single-end; + asahi-kasei,out6-single-end; + }; + + cs2000: clk-multiplier@4f { + #clock-cells = <0>; + compatible = "cirrus,cs2000-cp"; + reg = <0x4f>; + clocks = <&audio_clkout>, <&x12_clk>; + clock-names = "clk_in", "ref_clk"; + + assigned-clocks = <&cs2000>; + assigned-clock-rates = <24576000>; /* 1/1 divide */ + }; +}; + +&rcar_sound { + pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-names = "default"; + + /* Single DAI */ + #sound-dai-cells = <0>; + + /* audio_clkout0/1/2/3 */ + #clock-cells = <1>; + clock-frequency = <11289600>; + + status = "okay"; + + /* update <audio_clk_b> to <cs2000> */ + clocks = <&cpg CPG_MOD 1005>, + <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, + <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, + <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, + <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, + <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, + <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, + <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, + <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, + <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, + <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, + <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, + <&audio_clk_a>, <&cs2000>, + <&audio_clk_c>, + <&cpg CPG_CORE R8A7795_CLK_S0D4>; + + rcar_sound,dai { + dai0 { + playback = <&ssi0 &src0 &dvc0>; + capture = <&ssi1 &src1 &dvc1>; + }; + }; }; &sdhi0 { @@ -150,11 +257,19 @@ status = "okay"; }; +&ssi1 { + shared-pin; +}; + &wdt0 { timeout-sec = <60>; status = "okay"; }; +&audio_clk_a { + clock-frequency = <22579200>; +}; + &avb { pinctrl-0 = <&avb_pins>; pinctrl-names = "default"; -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 4/4] arm64: dts: h3ulcb: Sound SSI support @ 2016-09-02 16:25 ` Vladimir Barinov 0 siblings, 0 replies; 20+ messages in thread From: Vladimir Barinov @ 2016-09-02 16:25 UTC (permalink / raw) To: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland Cc: devicetree, linux-renesas-soc, Vladimir Barinov This supports SSI sound for H3ULCB board. SSI DMA mode used. CS2000 used as AUDIO_CLK_B. Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> --- Changes in version 3: - initially added Changes in version 4: - added comment for audio_clkout Changes in version 5: - renamed x12_clk node to x12 - renamed clk_multiplier node to clk-multiplier - renamed audio_clkout node to audio-clkout - renamed sound_clk node to sound-clk arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 115 +++++++++++++++++++++++++ 1 file changed, 115 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts index bbd7928..a254231 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts +++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts @@ -45,6 +45,12 @@ }; }; + x12_clk: x12 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24576000>; + }; + vcc_sdhi0: regulator-vcc-sdhi0 { compatible = "regulator-fixed"; @@ -68,6 +74,32 @@ states = <3300000 1 1800000 0>; }; + + audio_clkout: audio-clkout { + /* + * This is same as <&rcar_sound 0> + * but needed to avoid cs2000/rcar_sound probe dead-lock + */ + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <11289600>; + }; + + rsnd_ak4613: sound { + compatible = "simple-audio-card"; + + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcpu>; + simple-audio-card,frame-master = <&sndcpu>; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&ak4613>; + }; + }; }; &extal_clk { @@ -113,6 +141,17 @@ power-source = <1800>; }; + sound_pins: sound { + groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a"; + function = "ssi"; + }; + + sound_clk_pins: sound-clk { + groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a", + "audio_clkout_a", "audio_clkout3_a"; + function = "audio_clk"; + }; + usb1_pins: usb1 { groups = "usb1"; function = "usb1"; @@ -136,6 +176,73 @@ pinctrl-names = "default"; status = "okay"; + + clock-frequency = <100000>; + + ak4613: codec@10 { + compatible = "asahi-kasei,ak4613"; + #sound-dai-cells = <0>; + reg = <0x10>; + clocks = <&rcar_sound 3>; + + asahi-kasei,in1-single-end; + asahi-kasei,in2-single-end; + asahi-kasei,out1-single-end; + asahi-kasei,out2-single-end; + asahi-kasei,out3-single-end; + asahi-kasei,out4-single-end; + asahi-kasei,out5-single-end; + asahi-kasei,out6-single-end; + }; + + cs2000: clk-multiplier@4f { + #clock-cells = <0>; + compatible = "cirrus,cs2000-cp"; + reg = <0x4f>; + clocks = <&audio_clkout>, <&x12_clk>; + clock-names = "clk_in", "ref_clk"; + + assigned-clocks = <&cs2000>; + assigned-clock-rates = <24576000>; /* 1/1 divide */ + }; +}; + +&rcar_sound { + pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-names = "default"; + + /* Single DAI */ + #sound-dai-cells = <0>; + + /* audio_clkout0/1/2/3 */ + #clock-cells = <1>; + clock-frequency = <11289600>; + + status = "okay"; + + /* update <audio_clk_b> to <cs2000> */ + clocks = <&cpg CPG_MOD 1005>, + <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, + <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, + <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, + <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, + <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, + <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, + <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, + <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, + <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, + <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, + <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, + <&audio_clk_a>, <&cs2000>, + <&audio_clk_c>, + <&cpg CPG_CORE R8A7795_CLK_S0D4>; + + rcar_sound,dai { + dai0 { + playback = <&ssi0 &src0 &dvc0>; + capture = <&ssi1 &src1 &dvc1>; + }; + }; }; &sdhi0 { @@ -150,11 +257,19 @@ status = "okay"; }; +&ssi1 { + shared-pin; +}; + &wdt0 { timeout-sec = <60>; status = "okay"; }; +&audio_clk_a { + clock-frequency = <22579200>; +}; + &avb { pinctrl-0 = <&avb_pins>; pinctrl-names = "default"; -- 1.9.1 ^ permalink raw reply related [flat|nested] 20+ messages in thread
[parent not found: <1472833529-26308-1-git-send-email-vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org>]
* Re: [PATCH v5 4/4] arm64: dts: h3ulcb: Sound SSI support 2016-09-02 16:25 ` Vladimir Barinov @ 2016-09-05 0:27 ` Kuninori Morimoto -1 siblings, 0 replies; 20+ messages in thread From: Kuninori Morimoto @ 2016-09-05 0:27 UTC (permalink / raw) To: Vladimir Barinov Cc: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA Hi > This supports SSI sound for H3ULCB board. > SSI DMA mode used. CS2000 used as AUDIO_CLK_B. > > Signed-off-by: Vladimir Barinov <vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org> > Acked-by: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org> -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v5 4/4] arm64: dts: h3ulcb: Sound SSI support @ 2016-09-05 0:27 ` Kuninori Morimoto 0 siblings, 0 replies; 20+ messages in thread From: Kuninori Morimoto @ 2016-09-05 0:27 UTC (permalink / raw) To: Vladimir Barinov Cc: Simon Horman, Magnus Damm, Rob Herring, Mark Rutland, devicetree, linux-renesas-soc Hi > This supports SSI sound for H3ULCB board. > SSI DMA mode used. CS2000 used as AUDIO_CLK_B. > > Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> > Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> ^ permalink raw reply [flat|nested] 20+ messages in thread
[parent not found: <8737lf42rx.wl%kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>]
* Re: [PATCH v5 4/4] arm64: dts: h3ulcb: Sound SSI support 2016-09-05 0:27 ` Kuninori Morimoto @ 2016-09-05 12:26 ` Simon Horman -1 siblings, 0 replies; 20+ messages in thread From: Simon Horman @ 2016-09-05 12:26 UTC (permalink / raw) To: Kuninori Morimoto Cc: Vladimir Barinov, Magnus Damm, Rob Herring, Mark Rutland, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA On Mon, Sep 05, 2016 at 12:27:30AM +0000, Kuninori Morimoto wrote: > > Hi > > > This supports SSI sound for H3ULCB board. > > SSI DMA mode used. CS2000 used as AUDIO_CLK_B. > > > > Signed-off-by: Vladimir Barinov <vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org> > > Acked-by: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org> > > Acked-by: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org> Thanks, I have queued this up. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v5 4/4] arm64: dts: h3ulcb: Sound SSI support @ 2016-09-05 12:26 ` Simon Horman 0 siblings, 0 replies; 20+ messages in thread From: Simon Horman @ 2016-09-05 12:26 UTC (permalink / raw) To: Kuninori Morimoto Cc: Vladimir Barinov, Magnus Damm, Rob Herring, Mark Rutland, devicetree, linux-renesas-soc On Mon, Sep 05, 2016 at 12:27:30AM +0000, Kuninori Morimoto wrote: > > Hi > > > This supports SSI sound for H3ULCB board. > > SSI DMA mode used. CS2000 used as AUDIO_CLK_B. > > > > Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> > > Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> > > Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Thanks, I have queued this up. ^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2016-09-05 12:32 UTC | newest]
Thread overview: 20+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-09-02 16:23 [PATCH v5 0/4] arm64: renesas: enable H3ULCB board peripherals Vladimir Barinov
2016-09-02 16:23 ` Vladimir Barinov
[not found] ` <1472833419-26139-1-git-send-email-vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org>
2016-09-02 16:24 ` [PATCH v5 1/4] arm64: dts: h3ulcb: enable GPIO leds Vladimir Barinov
2016-09-02 16:24 ` Vladimir Barinov
2016-09-05 12:26 ` Simon Horman
2016-09-02 16:24 ` [PATCH v5 2/4] arm64: dts: h3ulcb: enable GPIO keys Vladimir Barinov
2016-09-02 16:24 ` Vladimir Barinov
2016-09-05 7:57 ` Geert Uytterhoeven
[not found] ` <CAMuHMdWXq8enfSUcwFK=6NXoZgJkqo=iScjO8A3ZO-sGrcxb4w-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2016-09-05 12:17 ` Simon Horman
2016-09-05 12:17 ` Simon Horman
2016-09-02 16:25 ` [PATCH v5 3/4] arm64: dts: h3ulcb: enable SDHI0 Vladimir Barinov
2016-09-02 16:25 ` Vladimir Barinov
[not found] ` <1472833508-26267-1-git-send-email-vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org>
2016-09-05 12:25 ` Simon Horman
2016-09-05 12:25 ` Simon Horman
2016-09-02 16:25 ` [PATCH v5 4/4] arm64: dts: h3ulcb: Sound SSI support Vladimir Barinov
2016-09-02 16:25 ` Vladimir Barinov
[not found] ` <1472833529-26308-1-git-send-email-vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org>
2016-09-05 0:27 ` Kuninori Morimoto
2016-09-05 0:27 ` Kuninori Morimoto
[not found] ` <8737lf42rx.wl%kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
2016-09-05 12:26 ` Simon Horman
2016-09-05 12:26 ` Simon Horman
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.