* [PATCH 0/3] ARM: dts: sun9i: Enable SDIO-based WiFi
@ 2016-10-28 10:11 ` Chen-Yu Tsai
0 siblings, 0 replies; 12+ messages in thread
From: Chen-Yu Tsai @ 2016-10-28 10:11 UTC (permalink / raw)
To: linux-arm-kernel
Hi Maxime,
Now that we have support for both PMICs, we can turn on the
regulators needed for the onboard WiFi chips.
This is a fairly simple series. The WiFi chips themselves are
supported by the brcmfmac driver, but the user needs to get an
nvram.txt file and put it in their firmware directory, in
addition to the firmware file in linux-firmware. Otherwise we
just need to enable the mmc controller and supply the vmmc and
vqmmc regulators.
Regards
ChenYu
Chen-Yu Tsai (3):
ARM: dts: sun9i: Add mmc1 pinmux setting
ARM: dts: sun9i: a80-optimus: Enable AP6330 WiFi
ARM: dts: sun9i: cubieboard4: Enable AP6330 WiFi
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 32 +++++++++++++++++++++++++++++
arch/arm/boot/dts/sun9i-a80-optimus.dts | 30 +++++++++++++++++++++++++++
arch/arm/boot/dts/sun9i-a80.dtsi | 8 ++++++++
3 files changed, 70 insertions(+)
--
2.9.3
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/3] ARM: dts: sun9i: Add mmc1 pinmux setting
@ 2016-10-28 10:11 ` Chen-Yu Tsai
0 siblings, 0 replies; 12+ messages in thread
From: Chen-Yu Tsai @ 2016-10-28 10:11 UTC (permalink / raw)
To: Maxime Ripard; +Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel
On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun9i-a80.dtsi | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi
index 3c5214cbe4e6..ab6a221027ef 100644
--- a/arch/arm/boot/dts/sun9i-a80.dtsi
+++ b/arch/arm/boot/dts/sun9i-a80.dtsi
@@ -700,6 +700,14 @@
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ mmc1_pins: mmc1 {
+ allwinner,pins = "PG0", "PG1" ,"PG2", "PG3",
+ "PG4", "PG5";
+ allwinner,function = "mmc1";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
mmc2_8bit_pins: mmc2_8bit {
allwinner,pins = "PC6", "PC7", "PC8", "PC9",
"PC10", "PC11", "PC12",
--
2.9.3
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH 1/3] ARM: dts: sun9i: Add mmc1 pinmux setting
@ 2016-10-28 10:11 ` Chen-Yu Tsai
0 siblings, 0 replies; 12+ messages in thread
From: Chen-Yu Tsai @ 2016-10-28 10:11 UTC (permalink / raw)
To: linux-arm-kernel
On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun9i-a80.dtsi | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi
index 3c5214cbe4e6..ab6a221027ef 100644
--- a/arch/arm/boot/dts/sun9i-a80.dtsi
+++ b/arch/arm/boot/dts/sun9i-a80.dtsi
@@ -700,6 +700,14 @@
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ mmc1_pins: mmc1 {
+ allwinner,pins = "PG0", "PG1" ,"PG2", "PG3",
+ "PG4", "PG5";
+ allwinner,function = "mmc1";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
mmc2_8bit_pins: mmc2_8bit {
allwinner,pins = "PC6", "PC7", "PC8", "PC9",
"PC10", "PC11", "PC12",
--
2.9.3
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH 1/3] ARM: dts: sun9i: Add mmc1 pinmux setting
@ 2016-10-28 10:11 ` Chen-Yu Tsai
0 siblings, 0 replies; 12+ messages in thread
From: Chen-Yu Tsai @ 2016-10-28 10:11 UTC (permalink / raw)
To: Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
arch/arm/boot/dts/sun9i-a80.dtsi | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi
index 3c5214cbe4e6..ab6a221027ef 100644
--- a/arch/arm/boot/dts/sun9i-a80.dtsi
+++ b/arch/arm/boot/dts/sun9i-a80.dtsi
@@ -700,6 +700,14 @@
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ mmc1_pins: mmc1 {
+ allwinner,pins = "PG0", "PG1" ,"PG2", "PG3",
+ "PG4", "PG5";
+ allwinner,function = "mmc1";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
mmc2_8bit_pins: mmc2_8bit {
allwinner,pins = "PC6", "PC7", "PC8", "PC9",
"PC10", "PC11", "PC12",
--
2.9.3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/3] ARM: dts: sun9i: a80-optimus: Enable AP6330 WiFi
@ 2016-10-28 10:11 ` Chen-Yu Tsai
0 siblings, 0 replies; 12+ messages in thread
From: Chen-Yu Tsai @ 2016-10-28 10:11 UTC (permalink / raw)
To: Maxime Ripard; +Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index ceb6ef15d669..7e036b2be762 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -105,6 +105,14 @@
enable-active-high;
gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ /* enables internal regulator and de-asserts reset */
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+ };
};
&ehci0 {
@@ -130,6 +138,21 @@
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>, <&wifi_en_pin_optimus>;
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_cldo3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc1_pins {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
@@ -199,6 +222,13 @@
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ wifi_en_pin_optimus: wifi_en_pin@0 {
+ allwinner,pins = "PL2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
&r_rsb {
--
2.9.3
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH 2/3] ARM: dts: sun9i: a80-optimus: Enable AP6330 WiFi
@ 2016-10-28 10:11 ` Chen-Yu Tsai
0 siblings, 0 replies; 12+ messages in thread
From: Chen-Yu Tsai @ 2016-10-28 10:11 UTC (permalink / raw)
To: linux-arm-kernel
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index ceb6ef15d669..7e036b2be762 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -105,6 +105,14 @@
enable-active-high;
gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ /* enables internal regulator and de-asserts reset */
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+ };
};
&ehci0 {
@@ -130,6 +138,21 @@
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>, <&wifi_en_pin_optimus>;
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_cldo3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc1_pins {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
@@ -199,6 +222,13 @@
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ wifi_en_pin_optimus: wifi_en_pin at 0 {
+ allwinner,pins = "PL2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
&r_rsb {
--
2.9.3
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH 2/3] ARM: dts: sun9i: a80-optimus: Enable AP6330 WiFi
@ 2016-10-28 10:11 ` Chen-Yu Tsai
0 siblings, 0 replies; 12+ messages in thread
From: Chen-Yu Tsai @ 2016-10-28 10:11 UTC (permalink / raw)
To: Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index ceb6ef15d669..7e036b2be762 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -105,6 +105,14 @@
enable-active-high;
gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ /* enables internal regulator and de-asserts reset */
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+ };
};
&ehci0 {
@@ -130,6 +138,21 @@
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>, <&wifi_en_pin_optimus>;
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_cldo3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc1_pins {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
@@ -199,6 +222,13 @@
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ wifi_en_pin_optimus: wifi_en_pin@0 {
+ allwinner,pins = "PL2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
&r_rsb {
--
2.9.3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 3/3] ARM: dts: sun9i: cubieboard4: Enable AP6330 WiFi
2016-10-28 10:11 ` Chen-Yu Tsai
@ 2016-10-28 10:11 ` Chen-Yu Tsai
-1 siblings, 0 replies; 12+ messages in thread
From: Chen-Yu Tsai @ 2016-10-28 10:11 UTC (permalink / raw)
To: Maxime Ripard; +Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 32 +++++++++++++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 439847acd41e..67b02fe7f11c 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -76,6 +76,14 @@
gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
};
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ /* enables internal regulator and de-asserts reset */
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+ };
};
&mmc0 {
@@ -88,6 +96,21 @@
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>, <&wifi_en_pin_cubieboard4>;
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_cldo3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc1_pins {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
@@ -128,6 +151,15 @@
status = "okay";
};
+&r_pio {
+ wifi_en_pin_cubieboard4: wifi_en_pin@0 {
+ allwinner,pins = "PL2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
&r_rsb {
status = "okay";
--
2.9.3
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH 3/3] ARM: dts: sun9i: cubieboard4: Enable AP6330 WiFi
@ 2016-10-28 10:11 ` Chen-Yu Tsai
0 siblings, 0 replies; 12+ messages in thread
From: Chen-Yu Tsai @ 2016-10-28 10:11 UTC (permalink / raw)
To: linux-arm-kernel
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 32 +++++++++++++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 439847acd41e..67b02fe7f11c 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -76,6 +76,14 @@
gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
};
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ /* enables internal regulator and de-asserts reset */
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+ };
};
&mmc0 {
@@ -88,6 +96,21 @@
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>, <&wifi_en_pin_cubieboard4>;
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_cldo3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc1_pins {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
@@ -128,6 +151,15 @@
status = "okay";
};
+&r_pio {
+ wifi_en_pin_cubieboard4: wifi_en_pin at 0 {
+ allwinner,pins = "PL2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
&r_rsb {
status = "okay";
--
2.9.3
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 0/3] ARM: dts: sun9i: Enable SDIO-based WiFi
2016-10-28 10:11 ` Chen-Yu Tsai
@ 2016-11-02 13:32 ` Maxime Ripard
-1 siblings, 0 replies; 12+ messages in thread
From: Maxime Ripard @ 2016-11-02 13:32 UTC (permalink / raw)
To: Chen-Yu Tsai; +Cc: devicetree, linux-arm-kernel, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 683 bytes --]
On Fri, Oct 28, 2016 at 06:11:51PM +0800, Chen-Yu Tsai wrote:
> Hi Maxime,
>
> Now that we have support for both PMICs, we can turn on the
> regulators needed for the onboard WiFi chips.
>
> This is a fairly simple series. The WiFi chips themselves are
> supported by the brcmfmac driver, but the user needs to get an
> nvram.txt file and put it in their firmware directory, in
> addition to the firmware file in linux-firmware. Otherwise we
> just need to enable the mmc controller and supply the vmmc and
> vqmmc regulators.
Applied all three, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 0/3] ARM: dts: sun9i: Enable SDIO-based WiFi
@ 2016-11-02 13:32 ` Maxime Ripard
0 siblings, 0 replies; 12+ messages in thread
From: Maxime Ripard @ 2016-11-02 13:32 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Oct 28, 2016 at 06:11:51PM +0800, Chen-Yu Tsai wrote:
> Hi Maxime,
>
> Now that we have support for both PMICs, we can turn on the
> regulators needed for the onboard WiFi chips.
>
> This is a fairly simple series. The WiFi chips themselves are
> supported by the brcmfmac driver, but the user needs to get an
> nvram.txt file and put it in their firmware directory, in
> addition to the firmware file in linux-firmware. Otherwise we
> just need to enable the mmc controller and supply the vmmc and
> vqmmc regulators.
Applied all three, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161102/f6a550a6/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread