From: Oleksij Rempel <o.rempel@pengutronix.de>
To: Shawn Guo <shawnguo@kernel.org>, Mark Brown <broonie@kernel.org>,
"Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>,
kernel@pengutronix.de, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, linux-clk@vger.kernel.org,
linux-kernel@vger.kernel.org,
Andrew Morton <akpm@linux-foundation.org>,
Liam Girdwood <lgirdwood@gmail.com>,
Leonard Crestez <leonard.crestez@nxp.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@codeaurora.org>,
Fabio Estevam <fabio.estevam@nxp.com>,
Russell King <linux@armlinux.org.uk>,
linux-imx@nxp.com, yibin.gong@nxp.com,
"A.s. Dong" <aisheng.dong@nxp.com>
Subject: [PATCH v9 5/6] regulator: pfuze100-regulator: provide pm_power_off_prepare handler
Date: Thu, 2 Aug 2018 12:34:24 +0200 [thread overview]
Message-ID: <20180802103425.3053-6-o.rempel@pengutronix.de> (raw)
In-Reply-To: <20180802103425.3053-1-o.rempel@pengutronix.de>
On some boards the SoC can use one pin "PMIC_STBY_REQ" to notify th PMIC
about state changes. In this case internal state of PMIC must be
preconfigured for upcomming state change.
It works fine with the current regulator framework, except with the
power-off case.
This patch is providing an optional pm_power_off_prepare handler
which will configure standby state of the PMIC to disable all power lines.
In my power consumption test on RIoTBoard, I got the following results:
power off without this patch: 320 mA
power off with this patch: 2 mA
suspend to ram: 40 mA
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
drivers/regulator/pfuze100-regulator.c | 91 ++++++++++++++++++++++++++
1 file changed, 91 insertions(+)
diff --git a/drivers/regulator/pfuze100-regulator.c b/drivers/regulator/pfuze100-regulator.c
index 31c3a236120a..1e43a9de3bd5 100644
--- a/drivers/regulator/pfuze100-regulator.c
+++ b/drivers/regulator/pfuze100-regulator.c
@@ -31,11 +31,17 @@
#define PFUZE100_COINVOL 0x1a
#define PFUZE100_SW1ABVOL 0x20
+#define PFUZE100_SW1ABMODE 0x23
#define PFUZE100_SW1CVOL 0x2e
+#define PFUZE100_SW1CMODE 0x31
#define PFUZE100_SW2VOL 0x35
+#define PFUZE100_SW2MODE 0x38
#define PFUZE100_SW3AVOL 0x3c
+#define PFUZE100_SW3AMODE 0x3f
#define PFUZE100_SW3BVOL 0x43
+#define PFUZE100_SW3BMODE 0x46
#define PFUZE100_SW4VOL 0x4a
+#define PFUZE100_SW4MODE 0x4d
#define PFUZE100_SWBSTCON1 0x66
#define PFUZE100_VREFDDRCON 0x6a
#define PFUZE100_VSNVSVOL 0x6b
@@ -46,6 +52,13 @@
#define PFUZE100_VGEN5VOL 0x70
#define PFUZE100_VGEN6VOL 0x71
+#define PFUZE100_SWxMODE_MASK 0xf
+#define PFUZE100_SWxMODE_APS_APS 0x8
+#define PFUZE100_SWxMODE_APS_OFF 0x4
+
+#define PFUZE100_VGENxLPWR BIT(6)
+#define PFUZE100_VGENxSTBY BIT(5)
+
enum chips { PFUZE100, PFUZE200, PFUZE3000 = 3, PFUZE3001 = 0x31, };
struct pfuze_regulator {
@@ -559,6 +572,69 @@ static inline struct device_node *match_of_node(int index)
}
#endif
+static struct pfuze_chip *syspm_pfuze_chip;
+
+static void pfuze_power_off_prepare(void)
+{
+ dev_info(syspm_pfuze_chip->dev, "Configure standy mode for power off");
+
+ /* Switch from default mode: APS/APS to APS/Off */
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW1ABMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW1CMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW2MODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW3AMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW3BMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW4MODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN1VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN2VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN3VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN4VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN5VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN6VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+}
+
+static int pfuze_power_off_prepare_init(struct pfuze_chip *pfuze_chip)
+{
+ if (pfuze_chip->chip_id != PFUZE100) {
+ dev_warn(pfuze_chip->dev, "Requested pm_power_off_prepare handler for not supported chip\n");
+ return -ENODEV;
+ }
+
+ if (pm_power_off_prepare) {
+ dev_warn(pfuze_chip->dev, "pm_power_off_prepare is already registered.\n");
+ return -EBUSY;
+ }
+
+ if (syspm_pfuze_chip) {
+ dev_warn(pfuze_chip->dev, "syspm_pfuze_chip is already set.\n");
+ return -EBUSY;
+ }
+
+ syspm_pfuze_chip = pfuze_chip;
+ pm_power_off_prepare = pfuze_power_off_prepare;
+
+ return 0;
+}
+
static int pfuze_identify(struct pfuze_chip *pfuze_chip)
{
unsigned int value;
@@ -753,6 +829,20 @@ static int pfuze100_regulator_probe(struct i2c_client *client,
}
}
+ if (of_property_read_bool(client->dev.of_node,
+ "fsl,pmic-stby-poweroff"))
+ return pfuze_power_off_prepare_init(pfuze_chip);
+
+ return 0;
+}
+
+static int pfuze100_regulator_remove(struct i2c_client *client)
+{
+ if (syspm_pfuze_chip) {
+ syspm_pfuze_chip = NULL;
+ pm_power_off_prepare = NULL;
+ }
+
return 0;
}
@@ -763,6 +853,7 @@ static struct i2c_driver pfuze_driver = {
.of_match_table = pfuze_dt_ids,
},
.probe = pfuze100_regulator_probe,
+ .remove = pfuze100_regulator_remove,
};
module_i2c_driver(pfuze_driver);
--
2.18.0
WARNING: multiple messages have this Message-ID (diff)
From: Oleksij Rempel <o.rempel@pengutronix.de>
To: Shawn Guo <shawnguo@kernel.org>, Mark Brown <broonie@kernel.org>,
"Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>,
devicetree@vger.kernel.org, yibin.gong@nxp.com,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@codeaurora.org>,
linux-kernel@vger.kernel.org, Liam Girdwood <lgirdwood@gmail.com>,
Oleksij Rempel <o.rempel@pengutronix.de>,
Rob Herring <robh+dt@kernel.org>,
linux-imx@nxp.com, kernel@pengutronix.de,
"A.s. Dong" <aisheng.dong@nxp.com>,
Fabio Estevam <fabio.estevam@nxp.com>,
Russell King <linux@armlinux.org.uk>,
Andrew Morton <akpm@linux-foundation.org>,
Leonard Crestez <leonard.crestez@nxp.com>,
linux-clk@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: [PATCH v9 5/6] regulator: pfuze100-regulator: provide pm_power_off_prepare handler
Date: Thu, 2 Aug 2018 12:34:24 +0200 [thread overview]
Message-ID: <20180802103425.3053-6-o.rempel@pengutronix.de> (raw)
In-Reply-To: <20180802103425.3053-1-o.rempel@pengutronix.de>
On some boards the SoC can use one pin "PMIC_STBY_REQ" to notify th PMIC
about state changes. In this case internal state of PMIC must be
preconfigured for upcomming state change.
It works fine with the current regulator framework, except with the
power-off case.
This patch is providing an optional pm_power_off_prepare handler
which will configure standby state of the PMIC to disable all power lines.
In my power consumption test on RIoTBoard, I got the following results:
power off without this patch: 320 mA
power off with this patch: 2 mA
suspend to ram: 40 mA
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
drivers/regulator/pfuze100-regulator.c | 91 ++++++++++++++++++++++++++
1 file changed, 91 insertions(+)
diff --git a/drivers/regulator/pfuze100-regulator.c b/drivers/regulator/pfuze100-regulator.c
index 31c3a236120a..1e43a9de3bd5 100644
--- a/drivers/regulator/pfuze100-regulator.c
+++ b/drivers/regulator/pfuze100-regulator.c
@@ -31,11 +31,17 @@
#define PFUZE100_COINVOL 0x1a
#define PFUZE100_SW1ABVOL 0x20
+#define PFUZE100_SW1ABMODE 0x23
#define PFUZE100_SW1CVOL 0x2e
+#define PFUZE100_SW1CMODE 0x31
#define PFUZE100_SW2VOL 0x35
+#define PFUZE100_SW2MODE 0x38
#define PFUZE100_SW3AVOL 0x3c
+#define PFUZE100_SW3AMODE 0x3f
#define PFUZE100_SW3BVOL 0x43
+#define PFUZE100_SW3BMODE 0x46
#define PFUZE100_SW4VOL 0x4a
+#define PFUZE100_SW4MODE 0x4d
#define PFUZE100_SWBSTCON1 0x66
#define PFUZE100_VREFDDRCON 0x6a
#define PFUZE100_VSNVSVOL 0x6b
@@ -46,6 +52,13 @@
#define PFUZE100_VGEN5VOL 0x70
#define PFUZE100_VGEN6VOL 0x71
+#define PFUZE100_SWxMODE_MASK 0xf
+#define PFUZE100_SWxMODE_APS_APS 0x8
+#define PFUZE100_SWxMODE_APS_OFF 0x4
+
+#define PFUZE100_VGENxLPWR BIT(6)
+#define PFUZE100_VGENxSTBY BIT(5)
+
enum chips { PFUZE100, PFUZE200, PFUZE3000 = 3, PFUZE3001 = 0x31, };
struct pfuze_regulator {
@@ -559,6 +572,69 @@ static inline struct device_node *match_of_node(int index)
}
#endif
+static struct pfuze_chip *syspm_pfuze_chip;
+
+static void pfuze_power_off_prepare(void)
+{
+ dev_info(syspm_pfuze_chip->dev, "Configure standy mode for power off");
+
+ /* Switch from default mode: APS/APS to APS/Off */
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW1ABMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW1CMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW2MODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW3AMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW3BMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW4MODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN1VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN2VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN3VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN4VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN5VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN6VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+}
+
+static int pfuze_power_off_prepare_init(struct pfuze_chip *pfuze_chip)
+{
+ if (pfuze_chip->chip_id != PFUZE100) {
+ dev_warn(pfuze_chip->dev, "Requested pm_power_off_prepare handler for not supported chip\n");
+ return -ENODEV;
+ }
+
+ if (pm_power_off_prepare) {
+ dev_warn(pfuze_chip->dev, "pm_power_off_prepare is already registered.\n");
+ return -EBUSY;
+ }
+
+ if (syspm_pfuze_chip) {
+ dev_warn(pfuze_chip->dev, "syspm_pfuze_chip is already set.\n");
+ return -EBUSY;
+ }
+
+ syspm_pfuze_chip = pfuze_chip;
+ pm_power_off_prepare = pfuze_power_off_prepare;
+
+ return 0;
+}
+
static int pfuze_identify(struct pfuze_chip *pfuze_chip)
{
unsigned int value;
@@ -753,6 +829,20 @@ static int pfuze100_regulator_probe(struct i2c_client *client,
}
}
+ if (of_property_read_bool(client->dev.of_node,
+ "fsl,pmic-stby-poweroff"))
+ return pfuze_power_off_prepare_init(pfuze_chip);
+
+ return 0;
+}
+
+static int pfuze100_regulator_remove(struct i2c_client *client)
+{
+ if (syspm_pfuze_chip) {
+ syspm_pfuze_chip = NULL;
+ pm_power_off_prepare = NULL;
+ }
+
return 0;
}
@@ -763,6 +853,7 @@ static struct i2c_driver pfuze_driver = {
.of_match_table = pfuze_dt_ids,
},
.probe = pfuze100_regulator_probe,
+ .remove = pfuze100_regulator_remove,
};
module_i2c_driver(pfuze_driver);
--
2.18.0
WARNING: multiple messages have this Message-ID (diff)
From: o.rempel@pengutronix.de (Oleksij Rempel)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v9 5/6] regulator: pfuze100-regulator: provide pm_power_off_prepare handler
Date: Thu, 2 Aug 2018 12:34:24 +0200 [thread overview]
Message-ID: <20180802103425.3053-6-o.rempel@pengutronix.de> (raw)
In-Reply-To: <20180802103425.3053-1-o.rempel@pengutronix.de>
On some boards the SoC can use one pin "PMIC_STBY_REQ" to notify th PMIC
about state changes. In this case internal state of PMIC must be
preconfigured for upcomming state change.
It works fine with the current regulator framework, except with the
power-off case.
This patch is providing an optional pm_power_off_prepare handler
which will configure standby state of the PMIC to disable all power lines.
In my power consumption test on RIoTBoard, I got the following results:
power off without this patch: 320 mA
power off with this patch: 2 mA
suspend to ram: 40 mA
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
drivers/regulator/pfuze100-regulator.c | 91 ++++++++++++++++++++++++++
1 file changed, 91 insertions(+)
diff --git a/drivers/regulator/pfuze100-regulator.c b/drivers/regulator/pfuze100-regulator.c
index 31c3a236120a..1e43a9de3bd5 100644
--- a/drivers/regulator/pfuze100-regulator.c
+++ b/drivers/regulator/pfuze100-regulator.c
@@ -31,11 +31,17 @@
#define PFUZE100_COINVOL 0x1a
#define PFUZE100_SW1ABVOL 0x20
+#define PFUZE100_SW1ABMODE 0x23
#define PFUZE100_SW1CVOL 0x2e
+#define PFUZE100_SW1CMODE 0x31
#define PFUZE100_SW2VOL 0x35
+#define PFUZE100_SW2MODE 0x38
#define PFUZE100_SW3AVOL 0x3c
+#define PFUZE100_SW3AMODE 0x3f
#define PFUZE100_SW3BVOL 0x43
+#define PFUZE100_SW3BMODE 0x46
#define PFUZE100_SW4VOL 0x4a
+#define PFUZE100_SW4MODE 0x4d
#define PFUZE100_SWBSTCON1 0x66
#define PFUZE100_VREFDDRCON 0x6a
#define PFUZE100_VSNVSVOL 0x6b
@@ -46,6 +52,13 @@
#define PFUZE100_VGEN5VOL 0x70
#define PFUZE100_VGEN6VOL 0x71
+#define PFUZE100_SWxMODE_MASK 0xf
+#define PFUZE100_SWxMODE_APS_APS 0x8
+#define PFUZE100_SWxMODE_APS_OFF 0x4
+
+#define PFUZE100_VGENxLPWR BIT(6)
+#define PFUZE100_VGENxSTBY BIT(5)
+
enum chips { PFUZE100, PFUZE200, PFUZE3000 = 3, PFUZE3001 = 0x31, };
struct pfuze_regulator {
@@ -559,6 +572,69 @@ static inline struct device_node *match_of_node(int index)
}
#endif
+static struct pfuze_chip *syspm_pfuze_chip;
+
+static void pfuze_power_off_prepare(void)
+{
+ dev_info(syspm_pfuze_chip->dev, "Configure standy mode for power off");
+
+ /* Switch from default mode: APS/APS to APS/Off */
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW1ABMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW1CMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW2MODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW3AMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW3BMODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_SW4MODE,
+ PFUZE100_SWxMODE_MASK, PFUZE100_SWxMODE_APS_OFF);
+
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN1VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN2VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN3VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN4VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN5VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+ regmap_update_bits(syspm_pfuze_chip->regmap, PFUZE100_VGEN6VOL,
+ PFUZE100_VGENxLPWR | PFUZE100_VGENxSTBY,
+ PFUZE100_VGENxSTBY);
+}
+
+static int pfuze_power_off_prepare_init(struct pfuze_chip *pfuze_chip)
+{
+ if (pfuze_chip->chip_id != PFUZE100) {
+ dev_warn(pfuze_chip->dev, "Requested pm_power_off_prepare handler for not supported chip\n");
+ return -ENODEV;
+ }
+
+ if (pm_power_off_prepare) {
+ dev_warn(pfuze_chip->dev, "pm_power_off_prepare is already registered.\n");
+ return -EBUSY;
+ }
+
+ if (syspm_pfuze_chip) {
+ dev_warn(pfuze_chip->dev, "syspm_pfuze_chip is already set.\n");
+ return -EBUSY;
+ }
+
+ syspm_pfuze_chip = pfuze_chip;
+ pm_power_off_prepare = pfuze_power_off_prepare;
+
+ return 0;
+}
+
static int pfuze_identify(struct pfuze_chip *pfuze_chip)
{
unsigned int value;
@@ -753,6 +829,20 @@ static int pfuze100_regulator_probe(struct i2c_client *client,
}
}
+ if (of_property_read_bool(client->dev.of_node,
+ "fsl,pmic-stby-poweroff"))
+ return pfuze_power_off_prepare_init(pfuze_chip);
+
+ return 0;
+}
+
+static int pfuze100_regulator_remove(struct i2c_client *client)
+{
+ if (syspm_pfuze_chip) {
+ syspm_pfuze_chip = NULL;
+ pm_power_off_prepare = NULL;
+ }
+
return 0;
}
@@ -763,6 +853,7 @@ static struct i2c_driver pfuze_driver = {
.of_match_table = pfuze_dt_ids,
},
.probe = pfuze100_regulator_probe,
+ .remove = pfuze100_regulator_remove,
};
module_i2c_driver(pfuze_driver);
--
2.18.0
next prev parent reply other threads:[~2018-08-02 10:35 UTC|newest]
Thread overview: 46+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-08-02 10:34 [PATCH v9 0/6] provide power off support for iMX6 with external PMIC Oleksij Rempel
2018-08-02 10:34 ` Oleksij Rempel
2018-08-02 10:34 ` [PATCH v9 1/6] ARM: imx6q: provide documentation for new fsl,pmic-stby-poweroff property Oleksij Rempel
2018-08-02 10:34 ` [PATCH v9 1/6] ARM: imx6q: provide documentation for new fsl, pmic-stby-poweroff property Oleksij Rempel
2018-09-12 1:04 ` [PATCH v9 1/6] ARM: imx6q: provide documentation for new fsl,pmic-stby-poweroff property Shawn Guo
2018-09-12 1:04 ` Shawn Guo
2018-08-02 10:34 ` [PATCH v9 2/6] ARM: imx6: register pm_power_off handler if "fsl,pmic-stby-poweroff" is set Oleksij Rempel
2018-08-02 10:34 ` [PATCH v9 2/6] ARM: imx6: register pm_power_off handler if "fsl, pmic-stby-poweroff" " Oleksij Rempel
2018-09-12 1:10 ` [PATCH v9 2/6] ARM: imx6: register pm_power_off handler if "fsl,pmic-stby-poweroff" " Shawn Guo
2018-09-12 1:10 ` Shawn Guo
2018-08-02 10:34 ` [PATCH v9 3/6] kernel/reboot.c: export pm_power_off_prepare Oleksij Rempel
2018-08-02 10:34 ` Oleksij Rempel
2018-08-02 10:44 ` Mark Brown
2018-08-02 10:44 ` Mark Brown
2018-08-02 10:44 ` Mark Brown
2018-08-02 10:47 ` Oleksij Rempel
2018-08-02 10:47 ` Oleksij Rempel
2018-08-02 11:35 ` Mark Brown
2018-08-02 11:35 ` Mark Brown
2018-08-27 1:48 ` Shawn Guo
2018-08-27 1:48 ` Shawn Guo
2018-09-06 10:15 ` Mark Brown
2018-09-06 10:15 ` Mark Brown
2018-09-07 7:35 ` Oleksij Rempel
2018-09-07 7:35 ` Oleksij Rempel
2018-09-09 2:00 ` Shawn Guo
2018-09-09 2:00 ` Shawn Guo
2018-09-09 2:00 ` Shawn Guo
2018-09-10 15:19 ` Mark Brown
2018-09-10 15:19 ` Mark Brown
2018-09-11 1:53 ` Shawn Guo
2018-09-11 1:53 ` Shawn Guo
2018-09-11 4:36 ` Oleksij Rempel
2018-09-11 4:36 ` Oleksij Rempel
2018-09-11 4:36 ` Oleksij Rempel
2018-09-11 15:19 ` Mark Brown
2018-09-11 15:19 ` Mark Brown
2018-08-02 10:34 ` [PATCH v9 4/6] regulator: pfuze100: add fsl,pmic-stby-poweroff property Oleksij Rempel
2018-08-02 10:34 ` [PATCH v9 4/6] regulator: pfuze100: add fsl, pmic-stby-poweroff property Oleksij Rempel
2018-08-02 10:34 ` Oleksij Rempel [this message]
2018-08-02 10:34 ` [PATCH v9 5/6] regulator: pfuze100-regulator: provide pm_power_off_prepare handler Oleksij Rempel
2018-08-02 10:34 ` Oleksij Rempel
2018-08-02 10:34 ` [PATCH v9 6/6] ARM: dts: imx6: RIoTboard provide standby on power off option Oleksij Rempel
2018-08-02 10:34 ` Oleksij Rempel
2018-09-12 1:11 ` Shawn Guo
2018-09-12 1:11 ` Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180802103425.3053-6-o.rempel@pengutronix.de \
--to=o.rempel@pengutronix.de \
--cc=aisheng.dong@nxp.com \
--cc=akpm@linux-foundation.org \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=fabio.estevam@nxp.com \
--cc=kernel@pengutronix.de \
--cc=leonard.crestez@nxp.com \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=mark.rutland@arm.com \
--cc=mturquette@baylibre.com \
--cc=rafael.j.wysocki@intel.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@codeaurora.org \
--cc=shawnguo@kernel.org \
--cc=yibin.gong@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.