* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
@ 2018-12-21 6:38 Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 01/11] spi-mem: Claim SPI bus before spi mem access Vignesh R
` (14 more replies)
0 siblings, 15 replies; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
U-Boot SPI NOR support (sf layer) is quite outdated as it does not
support 4 byte addressing opcodes, SFDP table parsing and different types of
quad mode enable sequences. Many newer flashes no longer support BANK
registers used by sf layer to a access >16MB space.
Also, many SPI controllers have special MMIO interfaces which provide
accelerated read/write access but require knowledge of flash parameters
to make use of it. Recent spi-mem layer provides a way to support such
flashes but sf layer isn't using that.
This patch series syncs SPI NOR framework from Linux v4.19. It also adds
spi-mem support on top.
So, we gain 4byte addressing support and SFDP support. This makes
migrating to U-Boot MTD framework easier.
Tested with few Spansion, micron and macronix flashes with TI's dra7xx,
k2g, am43xx EVMs. I dont have access to flashes from other vendors. So,
I would greatly appreciate testing on other platforms. Complete series
with dependencies here[1]
For clean build on some platforms, depends on CONFIG_SPI_FLASH migration
to defconfigs [2]
[1] https://github.com/r-vignesh/u-boot.git branch: spi-nor-mig-patch-v2
[2] https://patchwork.ozlabs.org/patch/1007485/
Simon, Stefan, Thanks for testing previous versions.
I haven't carried Tested-by's here as I have added back SPI_FLASH_BAR
support (but isn't enabled by default). Would be great if you could
retest this series.
I am hoping there won't be any major rework/changes after this round.
Change log:
Since v1:
Remove #ifindef __UBOOT__
Add back BAR support, but dont enable as default for all platform (see
10/11 for more details)
Enable SPI_FLASH_TINY on boards where there is SPL size constraint as
seen on travis ci builds.
Drop sf_mtd changes for now as it seems to cause issues.
v1: https://patchwork.ozlabs.org/cover/1012146/
Since RFC v2:
Fix issues reported by Simon Goldschmidt wrt 4 use of byte addressing opcode
Fix issues in compiling SFDP code
Re organize file names and Makefile to simply spi-nor-tiny inclusion
Remove SPI_FLASH_BAR and SF_DUAL_FLASH as these are no longer used
RFC v2: https://patchwork.ozlabs.org/cover/1007589/
Since RFC v1:
Add lightweight SPI flash stack for boards with SPL size constraints
Provide non DM version of spi-mem
Fix build issues on different platforms as reported by travis-ci on v1
RFC v1: https://patchwork.ozlabs.org/cover/1004689/
Vignesh R (11):
spi-mem: Claim SPI bus before spi mem access
spi: Add non DM version of SPI_MEM
sh: bitops: add hweight*() macros
mtd: spi: Port SPI NOR framework from Linux
mtd: spi: Switch to new SPI NOR framework
mtd: spi: Remove unused files
mtd: spi: Add lightweight SPI flash stack for SPL
configs: Enable SPI_FLASH_TINY for resource constrained boards
configs: Remove SF_DUAL_FLASH
configs: Don't use SPI_FLASH_BAR as default
MAINTAINERS: Add an entry for SPI NOR
MAINTAINERS | 9 +
arch/arm/mach-omap2/am33xx/Kconfig | 1 -
arch/sh/include/asm/bitops.h | 4 +
common/spl/Kconfig | 21 +-
configs/alt_defconfig | 1 -
configs/am57xx_evm_defconfig | 1 -
configs/am57xx_hs_evm_defconfig | 1 -
configs/ap121_defconfig | 1 -
configs/ap143_defconfig | 1 -
configs/avnet_ultra96_rev1_defconfig | 1 -
configs/axm_defconfig | 1 +
configs/axs101_defconfig | 1 -
configs/axs103_defconfig | 1 -
configs/bg0900_defconfig | 1 -
configs/blanche_defconfig | 1 -
configs/cl-som-am57x_defconfig | 1 -
configs/clearfog_defconfig | 1 -
configs/cm_t43_defconfig | 1 -
configs/da850_am18xxevm_defconfig | 1 +
configs/da850evm_nand_defconfig | 2 +-
configs/db-88f6820-amc_defconfig | 1 -
configs/db-88f6820-gp_defconfig | 1 +
configs/display5_defconfig | 1 -
configs/display5_factory_defconfig | 1 -
configs/dra7xx_evm_defconfig | 1 -
configs/dra7xx_hs_evm_defconfig | 1 -
configs/ds109_defconfig | 1 -
configs/ds414_defconfig | 1 -
configs/evb-rv1108_defconfig | 1 -
configs/gose_defconfig | 1 -
configs/helios4_defconfig | 1 -
configs/k2g_evm_defconfig | 1 -
configs/k2g_hs_evm_defconfig | 1 -
configs/koelsch_defconfig | 1 -
configs/lager_defconfig | 1 -
configs/maxbcm_defconfig | 1 -
configs/mt7629_rfb_defconfig | 1 -
configs/mx6sxsabreauto_defconfig | 1 -
configs/mx6sxsabresd_defconfig | 1 -
configs/mx6ul_14x14_evk_defconfig | 1 -
configs/mx6ul_9x9_evk_defconfig | 1 -
configs/mx6ull_14x14_evk_defconfig | 1 -
configs/mx6ull_14x14_evk_plugin_defconfig | 1 -
configs/mx7dsabresd_qspi_defconfig | 1 -
configs/porter_defconfig | 2 +-
configs/r8a77970_eagle_defconfig | 1 -
configs/silk_defconfig | 1 -
configs/socfpga_arria5_defconfig | 1 -
configs/socfpga_cyclone5_defconfig | 1 -
configs/socfpga_is1_defconfig | 1 -
configs/socfpga_sockit_defconfig | 1 -
configs/socfpga_socrates_defconfig | 1 -
configs/socfpga_sr1500_defconfig | 1 -
configs/socfpga_stratix10_defconfig | 1 -
configs/stout_defconfig | 2 +-
configs/taurus_defconfig | 3 +-
configs/topic_miami_defconfig | 1 -
configs/topic_miamilite_defconfig | 2 -
configs/topic_miamiplus_defconfig | 2 -
configs/turris_omnia_defconfig | 2 +-
configs/xilinx_versal_virt_defconfig | 1 -
configs/xilinx_zynqmp_mini_qspi_defconfig | 2 -
configs/xilinx_zynqmp_zc1232_revA_defconfig | 2 -
configs/xilinx_zynqmp_zc1254_revA_defconfig | 2 -
configs/xilinx_zynqmp_zc1275_revA_defconfig | 2 -
configs/xilinx_zynqmp_zc1275_revB_defconfig | 2 -
.../xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 -
.../xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 1 -
.../xilinx_zynqmp_zc1751_xm018_dc4_defconfig | 1 -
configs/xilinx_zynqmp_zcu100_revC_defconfig | 1 -
configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 1 -
configs/xilinx_zynqmp_zcu102_revA_defconfig | 1 -
configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 -
configs/xilinx_zynqmp_zcu104_revA_defconfig | 2 -
configs/xilinx_zynqmp_zcu104_revC_defconfig | 2 -
configs/xilinx_zynqmp_zcu106_revA_defconfig | 2 -
configs/xilinx_zynqmp_zcu111_revA_defconfig | 1 -
configs/zynq_cc108_defconfig | 1 -
configs/zynq_cse_qspi_defconfig | 1 -
configs/zynq_dlc20_rev1_0_defconfig | 1 -
configs/zynq_microzed_defconfig | 1 -
configs/zynq_minized_defconfig | 1 -
configs/zynq_z_turn_defconfig | 1 -
configs/zynq_zc702_defconfig | 1 -
configs/zynq_zc706_defconfig | 1 -
configs/zynq_zc770_xm010_defconfig | 1 -
configs/zynq_zc770_xm013_defconfig | 1 -
configs/zynq_zed_defconfig | 1 -
configs/zynq_zybo_defconfig | 1 -
configs/zynq_zybo_z7_defconfig | 1 -
doc/SPI/README.dual-flash | 92 -
doc/SPI/README.ti_qspi_dra_test | 1 -
drivers/mtd/spi/Kconfig | 16 +-
drivers/mtd/spi/Makefile | 12 +-
drivers/mtd/spi/sandbox.c | 36 +-
drivers/mtd/spi/sf_dataflash.c | 11 +-
drivers/mtd/spi/sf_internal.h | 225 +-
drivers/mtd/spi/sf_probe.c | 33 +-
drivers/mtd/spi/spi-nor-core.c | 2432 +++++++++++++++++
drivers/mtd/spi/spi-nor-ids.c | 297 ++
drivers/mtd/spi/spi-nor-tiny.c | 810 ++++++
drivers/mtd/spi/spi_flash.c | 1337 ---------
drivers/mtd/spi/spi_flash_ids.c | 211 --
drivers/spi/Kconfig | 9 +-
drivers/spi/Makefile | 1 +
drivers/spi/spi-mem-nodm.c | 89 +
drivers/spi/spi-mem.c | 6 +
drivers/spi/stm32_qspi.c | 4 +-
include/configs/T102xQDS.h | 1 -
include/configs/T102xRDB.h | 1 -
include/configs/T104xRDB.h | 1 -
include/configs/T208xQDS.h | 1 -
include/configs/T208xRDB.h | 1 -
include/configs/gw_ventana.h | 1 -
include/configs/km/kmp204x-common.h | 1 -
include/configs/ls1021aiot.h | 1 -
include/configs/socfpga_stratix10_socdk.h | 1 -
include/linux/mtd/cfi.h | 32 +
include/linux/mtd/spi-nor.h | 419 +++
include/spi_flash.h | 105 +-
120 files changed, 4266 insertions(+), 2058 deletions(-)
delete mode 100644 doc/SPI/README.dual-flash
create mode 100644 drivers/mtd/spi/spi-nor-core.c
create mode 100644 drivers/mtd/spi/spi-nor-ids.c
create mode 100644 drivers/mtd/spi/spi-nor-tiny.c
delete mode 100644 drivers/mtd/spi/spi_flash.c
delete mode 100644 drivers/mtd/spi/spi_flash_ids.c
create mode 100644 drivers/spi/spi-mem-nodm.c
create mode 100644 include/linux/mtd/cfi.h
create mode 100644 include/linux/mtd/spi-nor.h
--
2.20.1
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 01/11] spi-mem: Claim SPI bus before spi mem access
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
@ 2018-12-21 6:38 ` Vignesh R
2019-01-28 6:54 ` Jagan Teki
2018-12-21 6:38 ` [U-Boot] [PATCH v2 02/11] spi: Add non DM version of SPI_MEM Vignesh R
` (13 subsequent siblings)
14 siblings, 1 reply; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
It is necessary to call spi_claim_bus() before starting any SPI
transactions and this restriction would also apply when calling spi-mem
operationss. Therefore claim and release bus before requesting transfer
via exec_op.
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
drivers/spi/spi-mem.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
index 1da20b8de5c4..4c1463118ab2 100644
--- a/drivers/spi/spi-mem.c
+++ b/drivers/spi/spi-mem.c
@@ -231,7 +231,13 @@ int spi_mem_exec_op(struct spi_slave *slave, const struct spi_mem_op *op)
mutex_lock(&ctlr->bus_lock_mutex);
mutex_lock(&ctlr->io_mutex);
#endif
+ ret = spi_claim_bus(slave);
+ if (ret < 0)
+ return ret;
+
ret = ops->mem_ops->exec_op(slave, op);
+
+ spi_release_bus(slave);
#ifndef __UBOOT__
mutex_unlock(&ctlr->io_mutex);
mutex_unlock(&ctlr->bus_lock_mutex);
--
2.20.1
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 02/11] spi: Add non DM version of SPI_MEM
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 01/11] spi-mem: Claim SPI bus before spi mem access Vignesh R
@ 2018-12-21 6:38 ` Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 03/11] sh: bitops: add hweight*() macros Vignesh R
` (12 subsequent siblings)
14 siblings, 0 replies; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
Add non DM version of SPI_MEM to support easy migration to new SPI NOR
framework. This can be removed once DM_SPI conversion is complete.
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
drivers/spi/Kconfig | 4 +-
drivers/spi/Makefile | 1 +
drivers/spi/spi-mem-nodm.c | 89 ++++++++++++++++++++++++++++++++++++++
3 files changed, 92 insertions(+), 2 deletions(-)
create mode 100644 drivers/spi/spi-mem-nodm.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index a7bb5b35c294..5ee855fc5319 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -16,8 +16,6 @@ config DM_SPI
typically use driver-private data instead of extending the
spi_slave structure.
-if DM_SPI
-
config SPI_MEM
bool "SPI memory extension"
help
@@ -25,6 +23,8 @@ config SPI_MEM
This extension is meant to simplify interaction with SPI memories
by providing an high-level interface to send memory-like commands.
+if DM_SPI
+
config ALTERA_SPI
bool "Altera SPI driver"
help
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 392a92579578..32ba3b61f70d 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_SOFT_SPI) += soft_spi.o
obj-$(CONFIG_SPI_MEM) += spi-mem.o
else
obj-y += spi.o
+obj-$(CONFIG_SPI_MEM) += spi-mem-nodm.o
obj-$(CONFIG_SOFT_SPI) += soft_spi_legacy.o
endif
diff --git a/drivers/spi/spi-mem-nodm.c b/drivers/spi/spi-mem-nodm.c
new file mode 100644
index 000000000000..4d91761f56d3
--- /dev/null
+++ b/drivers/spi/spi-mem-nodm.c
@@ -0,0 +1,89 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+#include <spi.h>
+#include <spi-mem.h>
+
+int spi_mem_exec_op(struct spi_slave *slave,
+ const struct spi_mem_op *op)
+{
+ unsigned int pos = 0;
+ const u8 *tx_buf = NULL;
+ u8 *rx_buf = NULL;
+ u8 *op_buf;
+ int op_len;
+ u32 flag;
+ int ret;
+ int i;
+
+ if (op->data.nbytes) {
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ rx_buf = op->data.buf.in;
+ else
+ tx_buf = op->data.buf.out;
+ }
+
+ op_len = sizeof(op->cmd.opcode) + op->addr.nbytes + op->dummy.nbytes;
+ op_buf = calloc(1, op_len);
+
+ ret = spi_claim_bus(slave);
+ if (ret < 0)
+ return ret;
+
+ op_buf[pos++] = op->cmd.opcode;
+
+ if (op->addr.nbytes) {
+ for (i = 0; i < op->addr.nbytes; i++)
+ op_buf[pos + i] = op->addr.val >>
+ (8 * (op->addr.nbytes - i - 1));
+
+ pos += op->addr.nbytes;
+ }
+
+ if (op->dummy.nbytes)
+ memset(op_buf + pos, 0xff, op->dummy.nbytes);
+
+ /* 1st transfer: opcode + address + dummy cycles */
+ flag = SPI_XFER_BEGIN;
+ /* Make sure to set END bit if no tx or rx data messages follow */
+ if (!tx_buf && !rx_buf)
+ flag |= SPI_XFER_END;
+
+ ret = spi_xfer(slave, op_len * 8, op_buf, NULL, flag);
+ if (ret)
+ return ret;
+
+ /* 2nd transfer: rx or tx data path */
+ if (tx_buf || rx_buf) {
+ ret = spi_xfer(slave, op->data.nbytes * 8, tx_buf,
+ rx_buf, SPI_XFER_END);
+ if (ret)
+ return ret;
+ }
+
+ spi_release_bus(slave);
+
+ for (i = 0; i < pos; i++)
+ debug("%02x ", op_buf[i]);
+ debug("| [%dB %s] ",
+ tx_buf || rx_buf ? op->data.nbytes : 0,
+ tx_buf || rx_buf ? (tx_buf ? "out" : "in") : "-");
+ for (i = 0; i < op->data.nbytes; i++)
+ debug("%02x ", tx_buf ? tx_buf[i] : rx_buf[i]);
+ debug("[ret %d]\n", ret);
+
+ free(op_buf);
+
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+int spi_mem_adjust_op_size(struct spi_slave *slave,
+ struct spi_mem_op *op)
+{
+ return 0;
+}
--
2.20.1
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 03/11] sh: bitops: add hweight*() macros
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 01/11] spi-mem: Claim SPI bus before spi mem access Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 02/11] spi: Add non DM version of SPI_MEM Vignesh R
@ 2018-12-21 6:38 ` Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 04/11] mtd: spi: Port SPI NOR framework from Linux Vignesh R
` (11 subsequent siblings)
14 siblings, 0 replies; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
Add hweight*() macros required for moving to new SF layer
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
arch/sh/include/asm/bitops.h | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/sh/include/asm/bitops.h b/arch/sh/include/asm/bitops.h
index 8cb8385d76db..765f28f116bc 100644
--- a/arch/sh/include/asm/bitops.h
+++ b/arch/sh/include/asm/bitops.h
@@ -153,6 +153,10 @@ static inline int ffs (int x)
}
#define PLATFORM_FFS
+#define hweight32(x) generic_hweight32(x)
+#define hweight16(x) generic_hweight16(x)
+#define hweight8(x) generic_hweight8(x)
+
#endif /* __KERNEL__ */
#endif /* __ASM_SH_BITOPS_H */
--
2.20.1
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 04/11] mtd: spi: Port SPI NOR framework from Linux
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (2 preceding siblings ...)
2018-12-21 6:38 ` [U-Boot] [PATCH v2 03/11] sh: bitops: add hweight*() macros Vignesh R
@ 2018-12-21 6:38 ` Vignesh R
2019-01-27 18:48 ` Jagan Teki
2018-12-21 6:38 ` [U-Boot] [PATCH v2 05/11] mtd: spi: Switch to new SPI NOR framework Vignesh R
` (10 subsequent siblings)
14 siblings, 1 reply; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
support 4 byte addressing opcodes, SFDP table parsing and different types of
quad mode enable sequences. Many newer flashes no longer support BANK
registers used by sf layer to a access >16MB space.
Also, many SPI controllers have special MMIO interfaces which provide
accelerated read/write access but require knowledge of flash parameters
to make use of it. Recent spi-mem layer provides a way to support such
flashes but sf layer isn't using that.
So sync SPI NOR framework from Linux v4.19 and add spi-mem support on top.
in order to gain 4 byte addressing support, SFDP support and a way to
support SPI controllers with MMIO flash interface.
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
drivers/mtd/spi/spi-nor-core.c | 2590 ++++++++++++++++++++++++++++++++
include/linux/mtd/cfi.h | 32 +
include/linux/mtd/spi-nor.h | 410 +++++
3 files changed, 3032 insertions(+)
create mode 100644 drivers/mtd/spi/spi-nor-core.c
create mode 100644 include/linux/mtd/cfi.h
create mode 100644 include/linux/mtd/spi-nor.h
diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c
new file mode 100644
index 000000000000..597898d3b4af
--- /dev/null
+++ b/drivers/mtd/spi/spi-nor-core.c
@@ -0,0 +1,2590 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Based on m25p80.c, by Mike Lavender (mike at steroidmicros.com), with
+ * influence from lart.c (Abraham Van Der Merwe) and mtd_dataflash.c
+ *
+ * Copyright (C) 2005, Intec Automation Inc.
+ * Copyright (C) 2014, Freescale Semiconductor, Inc.
+ *
+ * Synced from Linux v4.19
+ */
+
+#include <common.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/log2.h>
+#include <linux/math64.h>
+#include <linux/sizes.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/spi-nor.h>
+#include <spi-mem.h>
+#include <spi.h>
+
+/* Define max times to check status register before we give up. */
+
+/*
+ * For everything but full-chip erase; probably could be much smaller, but kept
+ * around for safety for now
+ */
+
+#define HZ CONFIG_SYS_HZ
+
+#define DEFAULT_READY_WAIT_JIFFIES (40UL * HZ)
+
+#define SPI_NOR_MAX_ID_LEN 6
+#define SPI_NOR_MAX_ADDR_WIDTH 4
+
+struct flash_info {
+ char *name;
+
+ /*
+ * This array stores the ID bytes.
+ * The first three bytes are the JEDIC ID.
+ * JEDEC ID zero means "no ID" (mostly older chips).
+ */
+ u8 id[SPI_NOR_MAX_ID_LEN];
+ u8 id_len;
+
+ /* The size listed here is what works with SPINOR_OP_SE, which isn't
+ * necessarily called a "sector" by the vendor.
+ */
+ unsigned int sector_size;
+ u16 n_sectors;
+
+ u16 page_size;
+ u16 addr_width;
+
+ u16 flags;
+#define SECT_4K BIT(0) /* SPINOR_OP_BE_4K works uniformly */
+#define SPI_NOR_NO_ERASE BIT(1) /* No erase command needed */
+#define SST_WRITE BIT(2) /* use SST byte programming */
+#define SPI_NOR_NO_FR BIT(3) /* Can't do fastread */
+#define SECT_4K_PMC BIT(4) /* SPINOR_OP_BE_4K_PMC works uniformly */
+#define SPI_NOR_DUAL_READ BIT(5) /* Flash supports Dual Read */
+#define SPI_NOR_QUAD_READ BIT(6) /* Flash supports Quad Read */
+#define USE_FSR BIT(7) /* use flag status register */
+#define SPI_NOR_HAS_LOCK BIT(8) /* Flash supports lock/unlock via SR */
+#define SPI_NOR_HAS_TB BIT(9) /*
+ * Flash SR has Top/Bottom (TB) protect
+ * bit. Must be used with
+ * SPI_NOR_HAS_LOCK.
+ */
+#define SPI_S3AN BIT(10) /*
+ * Xilinx Spartan 3AN In-System Flash
+ * (MFR cannot be used for probing
+ * because it has the same value as
+ * ATMEL flashes)
+ */
+#define SPI_NOR_4B_OPCODES BIT(11) /*
+ * Use dedicated 4byte address op codes
+ * to support memory size above 128Mib.
+ */
+#define NO_CHIP_ERASE BIT(12) /* Chip does not support chip erase */
+#define SPI_NOR_SKIP_SFDP BIT(13) /* Skip parsing of SFDP tables */
+#define USE_CLSR BIT(14) /* use CLSR command */
+
+ int (*quad_enable)(struct spi_nor *nor);
+};
+
+#define JEDEC_MFR(info) ((info)->id[0])
+
+static int spi_nor_read_write_reg(struct spi_nor *nor, struct spi_mem_op
+ *op, void *buf)
+{
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ op->data.buf.in = buf;
+ else
+ op->data.buf.out = buf;
+ return spi_mem_exec_op(nor->spi, op);
+}
+
+static int spi_nor_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len)
+{
+ struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(code, 1),
+ SPI_MEM_OP_NO_ADDR,
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_IN(len, NULL, 1));
+ int ret;
+
+ ret = spi_nor_read_write_reg(nor, &op, val);
+ if (ret < 0)
+ dev_dbg(&flash->spimem->spi->dev, "error %d reading %x\n", ret,
+ code);
+
+ return ret;
+}
+
+static int spi_nor_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
+{
+ struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(opcode, 1),
+ SPI_MEM_OP_NO_ADDR,
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_OUT(len, NULL, 1));
+
+ return spi_nor_read_write_reg(nor, &op, buf);
+}
+
+static ssize_t spi_nor_read_data(struct spi_nor *nor, loff_t from, size_t len,
+ u_char *buf)
+{
+ struct spi_mem_op op =
+ SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 1),
+ SPI_MEM_OP_ADDR(nor->addr_width, from, 1),
+ SPI_MEM_OP_DUMMY(nor->read_dummy, 1),
+ SPI_MEM_OP_DATA_IN(len, buf, 1));
+ size_t remaining = len;
+ int ret;
+
+ /* get transfer protocols. */
+ op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->read_proto);
+ op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->read_proto);
+ op.dummy.buswidth = op.addr.buswidth;
+ op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->read_proto);
+
+ /* convert the dummy cycles to the number of bytes */
+ op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
+
+ while (remaining) {
+ op.data.nbytes = remaining < UINT_MAX ? remaining : UINT_MAX;
+ ret = spi_mem_adjust_op_size(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ ret = spi_mem_exec_op(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ op.addr.val += op.data.nbytes;
+ remaining -= op.data.nbytes;
+ op.data.buf.in += op.data.nbytes;
+ }
+
+ return len;
+}
+
+static ssize_t spi_nor_write_data(struct spi_nor *nor, loff_t to, size_t len,
+ const u_char *buf)
+{
+ struct spi_mem_op op =
+ SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 1),
+ SPI_MEM_OP_ADDR(nor->addr_width, to, 1),
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_OUT(len, buf, 1));
+ size_t remaining = len;
+ int ret;
+
+ /* get transfer protocols. */
+ op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->write_proto);
+ op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->write_proto);
+ op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->write_proto);
+
+ if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second)
+ op.addr.nbytes = 0;
+
+ while (remaining) {
+ op.data.nbytes = remaining < UINT_MAX ? remaining : UINT_MAX;
+ ret = spi_mem_adjust_op_size(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ ret = spi_mem_exec_op(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ op.addr.val += op.data.nbytes;
+ remaining -= op.data.nbytes;
+ op.data.buf.out += op.data.nbytes;
+ }
+
+ return len;
+}
+
+/*
+ * Read the status register, returning its value in the location
+ * Return the status register value.
+ * Returns negative if error occurred.
+ */
+static int read_sr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RDSR, &val, 1);
+ if (ret < 0) {
+ pr_debug("error %d reading SR\n", (int)ret);
+ return ret;
+ }
+
+ return val;
+}
+
+/*
+ * Read the flag status register, returning its value in the location
+ * Return the status register value.
+ * Returns negative if error occurred.
+ */
+static int read_fsr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RDFSR, &val, 1);
+ if (ret < 0) {
+ pr_debug("error %d reading FSR\n", ret);
+ return ret;
+ }
+
+ return val;
+}
+
+/*
+ * Read configuration register, returning its value in the
+ * location. Return the configuration register value.
+ * Returns negative if error occurred.
+ */
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+static int read_cr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RDCR, &val, 1);
+ if (ret < 0) {
+ dev_dbg(nor->dev, "error %d reading CR\n", ret);
+ return ret;
+ }
+
+ return val;
+}
+#endif
+
+/*
+ * Write status register 1 byte
+ * Returns negative if error occurred.
+ */
+static int write_sr(struct spi_nor *nor, u8 val)
+{
+ nor->cmd_buf[0] = val;
+ return nor->write_reg(nor, SPINOR_OP_WRSR, nor->cmd_buf, 1);
+}
+
+/*
+ * Set write enable latch with Write Enable command.
+ * Returns negative if error occurred.
+ */
+static int write_enable(struct spi_nor *nor)
+{
+ return nor->write_reg(nor, SPINOR_OP_WREN, NULL, 0);
+}
+
+/*
+ * Send write disable instruction to the chip.
+ */
+static int write_disable(struct spi_nor *nor)
+{
+ return nor->write_reg(nor, SPINOR_OP_WRDI, NULL, 0);
+}
+
+static struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd)
+{
+ return mtd->priv;
+}
+
+static u8 spi_nor_convert_opcode(u8 opcode, const u8 table[][2], size_t size)
+{
+ size_t i;
+
+ for (i = 0; i < size; i++)
+ if (table[i][0] == opcode)
+ return table[i][1];
+
+ /* No conversion found, keep input op code. */
+ return opcode;
+}
+
+static u8 spi_nor_convert_3to4_read(u8 opcode)
+{
+ static const u8 spi_nor_3to4_read[][2] = {
+ { SPINOR_OP_READ, SPINOR_OP_READ_4B },
+ { SPINOR_OP_READ_FAST, SPINOR_OP_READ_FAST_4B },
+ { SPINOR_OP_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B },
+ { SPINOR_OP_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B },
+ { SPINOR_OP_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B },
+ { SPINOR_OP_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B },
+
+ { SPINOR_OP_READ_1_1_1_DTR, SPINOR_OP_READ_1_1_1_DTR_4B },
+ { SPINOR_OP_READ_1_2_2_DTR, SPINOR_OP_READ_1_2_2_DTR_4B },
+ { SPINOR_OP_READ_1_4_4_DTR, SPINOR_OP_READ_1_4_4_DTR_4B },
+ };
+
+ return spi_nor_convert_opcode(opcode, spi_nor_3to4_read,
+ ARRAY_SIZE(spi_nor_3to4_read));
+}
+
+static u8 spi_nor_convert_3to4_program(u8 opcode)
+{
+ static const u8 spi_nor_3to4_program[][2] = {
+ { SPINOR_OP_PP, SPINOR_OP_PP_4B },
+ { SPINOR_OP_PP_1_1_4, SPINOR_OP_PP_1_1_4_4B },
+ { SPINOR_OP_PP_1_4_4, SPINOR_OP_PP_1_4_4_4B },
+ };
+
+ return spi_nor_convert_opcode(opcode, spi_nor_3to4_program,
+ ARRAY_SIZE(spi_nor_3to4_program));
+}
+
+static u8 spi_nor_convert_3to4_erase(u8 opcode)
+{
+ static const u8 spi_nor_3to4_erase[][2] = {
+ { SPINOR_OP_BE_4K, SPINOR_OP_BE_4K_4B },
+ { SPINOR_OP_BE_32K, SPINOR_OP_BE_32K_4B },
+ { SPINOR_OP_SE, SPINOR_OP_SE_4B },
+ };
+
+ return spi_nor_convert_opcode(opcode, spi_nor_3to4_erase,
+ ARRAY_SIZE(spi_nor_3to4_erase));
+}
+
+static void spi_nor_set_4byte_opcodes(struct spi_nor *nor,
+ const struct flash_info *info)
+{
+ /* Do some manufacturer fixups first */
+ switch (JEDEC_MFR(info)) {
+ case SNOR_MFR_SPANSION:
+ /* No small sector erase for 4-byte command set */
+ nor->erase_opcode = SPINOR_OP_SE;
+ nor->mtd.erasesize = info->sector_size;
+ break;
+
+ default:
+ break;
+ }
+
+ nor->read_opcode = spi_nor_convert_3to4_read(nor->read_opcode);
+ nor->program_opcode = spi_nor_convert_3to4_program(nor->program_opcode);
+ nor->erase_opcode = spi_nor_convert_3to4_erase(nor->erase_opcode);
+}
+
+/* Enable/disable 4-byte addressing mode. */
+static int set_4byte(struct spi_nor *nor, const struct flash_info *info,
+ int enable)
+{
+ int status;
+ bool need_wren = false;
+ u8 cmd;
+
+ switch (JEDEC_MFR(info)) {
+ case SNOR_MFR_ST:
+ case SNOR_MFR_MICRON:
+ /* Some Micron need WREN command; all will accept it */
+ need_wren = true;
+ case SNOR_MFR_MACRONIX:
+ case SNOR_MFR_WINBOND:
+ if (need_wren)
+ write_enable(nor);
+
+ cmd = enable ? SPINOR_OP_EN4B : SPINOR_OP_EX4B;
+ status = nor->write_reg(nor, cmd, NULL, 0);
+ if (need_wren)
+ write_disable(nor);
+
+ if (!status && !enable &&
+ JEDEC_MFR(info) == SNOR_MFR_WINBOND) {
+ /*
+ * On Winbond W25Q256FV, leaving 4byte mode causes
+ * the Extended Address Register to be set to 1, so all
+ * 3-byte-address reads come from the second 16M.
+ * We must clear the register to enable normal behavior.
+ */
+ write_enable(nor);
+ nor->cmd_buf[0] = 0;
+ nor->write_reg(nor, SPINOR_OP_WREAR, nor->cmd_buf, 1);
+ write_disable(nor);
+ }
+
+ return status;
+ default:
+ /* Spansion style */
+ nor->cmd_buf[0] = enable << 7;
+ return nor->write_reg(nor, SPINOR_OP_BRWR, nor->cmd_buf, 1);
+ }
+}
+
+static int spi_nor_sr_ready(struct spi_nor *nor)
+{
+ int sr = read_sr(nor);
+
+ if (sr < 0)
+ return sr;
+
+#ifndef CONFIG_SPL_BUILD
+ if (nor->flags & SNOR_F_USE_CLSR && sr & (SR_E_ERR | SR_P_ERR)) {
+ if (sr & SR_E_ERR)
+ dev_dbg(nor->dev, "Erase Error occurred\n");
+ else
+ dev_dbg(nor->dev, "Programming Error occurred\n");
+
+ nor->write_reg(nor, SPINOR_OP_CLSR, NULL, 0);
+ return -EIO;
+ }
+#endif
+
+ return !(sr & SR_WIP);
+}
+
+static int spi_nor_fsr_ready(struct spi_nor *nor)
+{
+ int fsr = read_fsr(nor);
+
+ if (fsr < 0)
+ return fsr;
+#ifndef CONFIG_SPL_BUILD
+ if (fsr & (FSR_E_ERR | FSR_P_ERR)) {
+ if (fsr & FSR_E_ERR)
+ dev_dbg(nor->dev, "Erase operation failed.\n");
+ else
+ dev_dbg(nor->dev, "Program operation failed.\n");
+
+ if (fsr & FSR_PT_ERR)
+ dev_dbg(nor->dev,
+ "Attempted to modify a protected sector.\n");
+
+ nor->write_reg(nor, SPINOR_OP_CLFSR, NULL, 0);
+ return -EIO;
+ }
+#endif
+ return fsr & FSR_READY;
+}
+
+static int spi_nor_ready(struct spi_nor *nor)
+{
+ int sr, fsr;
+
+ sr = spi_nor_sr_ready(nor);
+ if (sr < 0)
+ return sr;
+ fsr = nor->flags & SNOR_F_USE_FSR ? spi_nor_fsr_ready(nor) : 1;
+ if (fsr < 0)
+ return fsr;
+ return sr && fsr;
+}
+
+/*
+ * Service routine to read status register until ready, or timeout occurs.
+ * Returns non-zero if error.
+ */
+static int spi_nor_wait_till_ready_with_timeout(struct spi_nor *nor,
+ unsigned long timeout)
+{
+ unsigned long timebase;
+ int ret;
+
+ timebase = get_timer(0);
+
+ while (get_timer(timebase) < timeout) {
+ ret = spi_nor_ready(nor);
+ if (ret < 0)
+ return ret;
+ if (ret)
+ return 0;
+ }
+
+ dev_err(nor->dev, "flash operation timed out\n");
+
+ return -ETIMEDOUT;
+}
+
+static int spi_nor_wait_till_ready(struct spi_nor *nor)
+{
+ return spi_nor_wait_till_ready_with_timeout(nor,
+ DEFAULT_READY_WAIT_JIFFIES);
+}
+
+/*
+ * Initiate the erasure of a single sector
+ */
+static int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
+{
+ u8 buf[SPI_NOR_MAX_ADDR_WIDTH];
+ int i;
+
+ if (nor->erase)
+ return nor->erase(nor, addr);
+
+ /*
+ * Default implementation, if driver doesn't have a specialized HW
+ * control
+ */
+ for (i = nor->addr_width - 1; i >= 0; i--) {
+ buf[i] = addr & 0xff;
+ addr >>= 8;
+ }
+
+ return nor->write_reg(nor, nor->erase_opcode, buf, nor->addr_width);
+}
+
+/*
+ * Erase an address range on the nor chip. The address range may extend
+ * one or more erase sectors. Return an error is there is a problem erasing.
+ */
+static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ u32 addr, len, rem;
+ int ret;
+
+ dev_dbg(nor->dev, "at 0x%llx, len %lld\n", (long long)instr->addr,
+ (long long)instr->len);
+
+ div_u64_rem(instr->len, mtd->erasesize, &rem);
+ if (rem)
+ return -EINVAL;
+
+ addr = instr->addr;
+ len = instr->len;
+
+ while (len) {
+ write_enable(nor);
+
+ ret = spi_nor_erase_sector(nor, addr);
+ if (ret)
+ goto erase_err;
+
+ addr += mtd->erasesize;
+ len -= mtd->erasesize;
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto erase_err;
+ }
+
+ write_disable(nor);
+
+erase_err:
+ return ret;
+}
+
+#if defined(CONFIG_SPI_FLASH_STMICRO) || defined(CONFIG_SPI_FLASH_SST)
+/* Write status register and ensure bits in mask match written values */
+static int write_sr_and_check(struct spi_nor *nor, u8 status_new, u8 mask)
+{
+ int ret;
+
+ write_enable(nor);
+ ret = write_sr(nor, status_new);
+ if (ret)
+ return ret;
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ return ret;
+
+ ret = read_sr(nor);
+ if (ret < 0)
+ return ret;
+
+ return ((ret & mask) != (status_new & mask)) ? -EIO : 0;
+}
+
+static void stm_get_locked_range(struct spi_nor *nor, u8 sr, loff_t *ofs,
+ uint64_t *len)
+{
+ struct mtd_info *mtd = &nor->mtd;
+ u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
+ int shift = ffs(mask) - 1;
+ int pow;
+
+ if (!(sr & mask)) {
+ /* No protection */
+ *ofs = 0;
+ *len = 0;
+ } else {
+ pow = ((sr & mask) ^ mask) >> shift;
+ *len = mtd->size >> pow;
+ if (nor->flags & SNOR_F_HAS_SR_TB && sr & SR_TB)
+ *ofs = 0;
+ else
+ *ofs = mtd->size - *len;
+ }
+}
+
+/*
+ * Return 1 if the entire region is locked (if @locked is true) or unlocked (if
+ * @locked is false); 0 otherwise
+ */
+static int stm_check_lock_status_sr(struct spi_nor *nor, loff_t ofs, u64 len,
+ u8 sr, bool locked)
+{
+ loff_t lock_offs;
+ uint64_t lock_len;
+
+ if (!len)
+ return 1;
+
+ stm_get_locked_range(nor, sr, &lock_offs, &lock_len);
+
+ if (locked)
+ /* Requested range is a sub-range of locked range */
+ return (ofs + len <= lock_offs + lock_len) && (ofs >= lock_offs);
+ else
+ /* Requested range does not overlap with locked range */
+ return (ofs >= lock_offs + lock_len) || (ofs + len <= lock_offs);
+}
+
+static int stm_is_locked_sr(struct spi_nor *nor, loff_t ofs, uint64_t len,
+ u8 sr)
+{
+ return stm_check_lock_status_sr(nor, ofs, len, sr, true);
+}
+
+static int stm_is_unlocked_sr(struct spi_nor *nor, loff_t ofs, uint64_t len,
+ u8 sr)
+{
+ return stm_check_lock_status_sr(nor, ofs, len, sr, false);
+}
+
+/*
+ * Lock a region of the flash. Compatible with ST Micro and similar flash.
+ * Supports the block protection bits BP{0,1,2} in the status register
+ * (SR). Does not support these features found in newer SR bitfields:
+ * - SEC: sector/block protect - only handle SEC=0 (block protect)
+ * - CMP: complement protect - only support CMP=0 (range is not complemented)
+ *
+ * Support for the following is provided conditionally for some flash:
+ * - TB: top/bottom protect
+ *
+ * Sample table portion for 8MB flash (Winbond w25q64fw):
+ *
+ * SEC | TB | BP2 | BP1 | BP0 | Prot Length | Protected Portion
+ * --------------------------------------------------------------------------
+ * X | X | 0 | 0 | 0 | NONE | NONE
+ * 0 | 0 | 0 | 0 | 1 | 128 KB | Upper 1/64
+ * 0 | 0 | 0 | 1 | 0 | 256 KB | Upper 1/32
+ * 0 | 0 | 0 | 1 | 1 | 512 KB | Upper 1/16
+ * 0 | 0 | 1 | 0 | 0 | 1 MB | Upper 1/8
+ * 0 | 0 | 1 | 0 | 1 | 2 MB | Upper 1/4
+ * 0 | 0 | 1 | 1 | 0 | 4 MB | Upper 1/2
+ * X | X | 1 | 1 | 1 | 8 MB | ALL
+ * ------|-------|-------|-------|-------|---------------|-------------------
+ * 0 | 1 | 0 | 0 | 1 | 128 KB | Lower 1/64
+ * 0 | 1 | 0 | 1 | 0 | 256 KB | Lower 1/32
+ * 0 | 1 | 0 | 1 | 1 | 512 KB | Lower 1/16
+ * 0 | 1 | 1 | 0 | 0 | 1 MB | Lower 1/8
+ * 0 | 1 | 1 | 0 | 1 | 2 MB | Lower 1/4
+ * 0 | 1 | 1 | 1 | 0 | 4 MB | Lower 1/2
+ *
+ * Returns negative on errors, 0 on success.
+ */
+static int stm_lock(struct spi_nor *nor, loff_t ofs, uint64_t len)
+{
+ struct mtd_info *mtd = &nor->mtd;
+ int status_old, status_new;
+ u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
+ u8 shift = ffs(mask) - 1, pow, val;
+ loff_t lock_len;
+ bool can_be_top = true, can_be_bottom = nor->flags & SNOR_F_HAS_SR_TB;
+ bool use_top;
+
+ status_old = read_sr(nor);
+ if (status_old < 0)
+ return status_old;
+
+ /* If nothing in our range is unlocked, we don't need to do anything */
+ if (stm_is_locked_sr(nor, ofs, len, status_old))
+ return 0;
+
+ /* If anything below us is unlocked, we can't use 'bottom' protection */
+ if (!stm_is_locked_sr(nor, 0, ofs, status_old))
+ can_be_bottom = false;
+
+ /* If anything above us is unlocked, we can't use 'top' protection */
+ if (!stm_is_locked_sr(nor, ofs + len, mtd->size - (ofs + len),
+ status_old))
+ can_be_top = false;
+
+ if (!can_be_bottom && !can_be_top)
+ return -EINVAL;
+
+ /* Prefer top, if both are valid */
+ use_top = can_be_top;
+
+ /* lock_len: length of region that should end up locked */
+ if (use_top)
+ lock_len = mtd->size - ofs;
+ else
+ lock_len = ofs + len;
+
+ /*
+ * Need smallest pow such that:
+ *
+ * 1 / (2^pow) <= (len / size)
+ *
+ * so (assuming power-of-2 size) we do:
+ *
+ * pow = ceil(log2(size / len)) = log2(size) - floor(log2(len))
+ */
+ pow = ilog2(mtd->size) - ilog2(lock_len);
+ val = mask - (pow << shift);
+ if (val & ~mask)
+ return -EINVAL;
+ /* Don't "lock" with no region! */
+ if (!(val & mask))
+ return -EINVAL;
+
+ status_new = (status_old & ~mask & ~SR_TB) | val;
+
+ /* Disallow further writes if WP pin is asserted */
+ status_new |= SR_SRWD;
+
+ if (!use_top)
+ status_new |= SR_TB;
+
+ /* Don't bother if they're the same */
+ if (status_new == status_old)
+ return 0;
+
+ /* Only modify protection if it will not unlock other areas */
+ if ((status_new & mask) < (status_old & mask))
+ return -EINVAL;
+
+ return write_sr_and_check(nor, status_new, mask);
+}
+
+/*
+ * Unlock a region of the flash. See stm_lock() for more info
+ *
+ * Returns negative on errors, 0 on success.
+ */
+static int stm_unlock(struct spi_nor *nor, loff_t ofs, uint64_t len)
+{
+ struct mtd_info *mtd = &nor->mtd;
+ int status_old, status_new;
+ u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
+ u8 shift = ffs(mask) - 1, pow, val;
+ loff_t lock_len;
+ bool can_be_top = true, can_be_bottom = nor->flags & SNOR_F_HAS_SR_TB;
+ bool use_top;
+
+ status_old = read_sr(nor);
+ if (status_old < 0)
+ return status_old;
+
+ /* If nothing in our range is locked, we don't need to do anything */
+ if (stm_is_unlocked_sr(nor, ofs, len, status_old))
+ return 0;
+
+ /* If anything below us is locked, we can't use 'top' protection */
+ if (!stm_is_unlocked_sr(nor, 0, ofs, status_old))
+ can_be_top = false;
+
+ /* If anything above us is locked, we can't use 'bottom' protection */
+ if (!stm_is_unlocked_sr(nor, ofs + len, mtd->size - (ofs + len),
+ status_old))
+ can_be_bottom = false;
+
+ if (!can_be_bottom && !can_be_top)
+ return -EINVAL;
+
+ /* Prefer top, if both are valid */
+ use_top = can_be_top;
+
+ /* lock_len: length of region that should remain locked */
+ if (use_top)
+ lock_len = mtd->size - (ofs + len);
+ else
+ lock_len = ofs;
+
+ /*
+ * Need largest pow such that:
+ *
+ * 1 / (2^pow) >= (len / size)
+ *
+ * so (assuming power-of-2 size) we do:
+ *
+ * pow = floor(log2(size / len)) = log2(size) - ceil(log2(len))
+ */
+ pow = ilog2(mtd->size) - order_base_2(lock_len);
+ if (lock_len == 0) {
+ val = 0; /* fully unlocked */
+ } else {
+ val = mask - (pow << shift);
+ /* Some power-of-two sizes are not supported */
+ if (val & ~mask)
+ return -EINVAL;
+ }
+
+ status_new = (status_old & ~mask & ~SR_TB) | val;
+
+ /* Don't protect status register if we're fully unlocked */
+ if (lock_len == 0)
+ status_new &= ~SR_SRWD;
+
+ if (!use_top)
+ status_new |= SR_TB;
+
+ /* Don't bother if they're the same */
+ if (status_new == status_old)
+ return 0;
+
+ /* Only modify protection if it will not lock other areas */
+ if ((status_new & mask) > (status_old & mask))
+ return -EINVAL;
+
+ return write_sr_and_check(nor, status_new, mask);
+}
+
+/*
+ * Check if a region of the flash is (completely) locked. See stm_lock() for
+ * more info.
+ *
+ * Returns 1 if entire region is locked, 0 if any portion is unlocked, and
+ * negative on errors.
+ */
+static int stm_is_locked(struct spi_nor *nor, loff_t ofs, uint64_t len)
+{
+ int status;
+
+ status = read_sr(nor);
+ if (status < 0)
+ return status;
+
+ return stm_is_locked_sr(nor, ofs, len, status);
+}
+#endif /* CONFIG_SPI_FLASH_STMICRO */
+
+/* Used when the "_ext_id" is two bytes@most */
+#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
+ .id = { \
+ ((_jedec_id) >> 16) & 0xff, \
+ ((_jedec_id) >> 8) & 0xff, \
+ (_jedec_id) & 0xff, \
+ ((_ext_id) >> 8) & 0xff, \
+ (_ext_id) & 0xff, \
+ }, \
+ .id_len = (!(_jedec_id) ? 0 : (3 + ((_ext_id) ? 2 : 0))), \
+ .sector_size = (_sector_size), \
+ .n_sectors = (_n_sectors), \
+ .page_size = 256, \
+ .flags = (_flags),
+
+#define INFO6(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
+ .id = { \
+ ((_jedec_id) >> 16) & 0xff, \
+ ((_jedec_id) >> 8) & 0xff, \
+ (_jedec_id) & 0xff, \
+ ((_ext_id) >> 16) & 0xff, \
+ ((_ext_id) >> 8) & 0xff, \
+ (_ext_id) & 0xff, \
+ }, \
+ .id_len = 6, \
+ .sector_size = (_sector_size), \
+ .n_sectors = (_n_sectors), \
+ .page_size = 256, \
+ .flags = (_flags),
+
+/* NOTE: double check command sets and memory organization when you add
+ * more nor chips. This current list focusses on newer chips, which
+ * have been converging on command sets which including JEDEC ID.
+ *
+ * All newly added entries should describe *hardware* and should use SECT_4K
+ * (or SECT_4K_PMC) if hardware supports erasing 4 KiB sectors. For usage
+ * scenarios excluding small sectors there is config option that can be
+ * disabled: CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.
+ * For historical (and compatibility) reasons (before we got above config) some
+ * old entries may be missing 4K flag.
+ */
+const struct flash_info spi_nor_ids[] = {
+#ifdef CONFIG_SPI_FLASH_ATMEL /* ATMEL */
+ /* Atmel -- some are (confusingly) marketed as "DataFlash" */
+ { "at26df321", INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) },
+ { "at25df321a", INFO(0x1f4701, 0, 64 * 1024, 64, SECT_4K) },
+
+ { "at45db011d", INFO(0x1f2200, 0, 64 * 1024, 4, SECT_4K) },
+ { "at45db021d", INFO(0x1f2300, 0, 64 * 1024, 8, SECT_4K) },
+ { "at45db041d", INFO(0x1f2400, 0, 64 * 1024, 8, SECT_4K) },
+ { "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) },
+ { "at45db161d", INFO(0x1f2600, 0, 64 * 1024, 32, SECT_4K) },
+ { "at45db321d", INFO(0x1f2700, 0, 64 * 1024, 64, SECT_4K) },
+ { "at45db641d", INFO(0x1f2800, 0, 64 * 1024, 128, SECT_4K) },
+ { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) },
+#endif
+#ifdef CONFIG_SPI_FLASH_EON /* EON */
+ /* EON -- en25xxx */
+ { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) },
+ { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) },
+ { "en25qh128", INFO(0x1c7018, 0, 64 * 1024, 256, 0) },
+ { "en25s64", INFO(0x1c3817, 0, 64 * 1024, 128, SECT_4K) },
+#endif
+#ifdef CONFIG_SPI_FLASH_GIGADEVICE /* GIGADEVICE */
+ /* GigaDevice */
+ {
+ "gd25q16", INFO(0xc84015, 0, 64 * 1024, 32,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ "gd25q32", INFO(0xc84016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ "gd25lq32", INFO(0xc86016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ "gd25q64", INFO(0xc84017, 0, 64 * 1024, 128,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+#endif
+#ifdef CONFIG_SPI_FLASH_ISSI /* ISSI */
+ /* ISSI */
+ { "is25lq040b", INFO(0x9d4013, 0, 64 * 1024, 8,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "is25lp032", INFO(0x9d6016, 0, 64 * 1024, 64, 0) },
+ { "is25lp064", INFO(0x9d6017, 0, 64 * 1024, 128, 0) },
+ { "is25lp128", INFO(0x9d6018, 0, 64 * 1024, 256,
+ SECT_4K | SPI_NOR_DUAL_READ) },
+ { "is25lp256", INFO(0x9d6019, 0, 64 * 1024, 512,
+ SECT_4K | SPI_NOR_DUAL_READ) },
+ { "is25wp032", INFO(0x9d7016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "is25wp064", INFO(0x9d7017, 0, 64 * 1024, 128,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "is25wp128", INFO(0x9d7018, 0, 64 * 1024, 256,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+#endif
+#ifdef CONFIG_SPI_FLASH_MACRONIX /* MACRONIX */
+ /* Macronix */
+ { "mx25l2005a", INFO(0xc22012, 0, 64 * 1024, 4, SECT_4K) },
+ { "mx25l4005a", INFO(0xc22013, 0, 64 * 1024, 8, SECT_4K) },
+ { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) },
+ { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) },
+ { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, SECT_4K) },
+ { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, SECT_4K) },
+ { "mx25u2033e", INFO(0xc22532, 0, 64 * 1024, 4, SECT_4K) },
+ { "mx25u1635e", INFO(0xc22535, 0, 64 * 1024, 32, SECT_4K) },
+ { "mx25u6435f", INFO(0xc22537, 0, 64 * 1024, 128, SECT_4K) },
+ { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
+ { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
+ { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "mx25u25635f", INFO(0xc22539, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_4B_OPCODES) },
+ { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
+ { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+ { "mx66u51235f", INFO(0xc2253a, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+ { "mx66l1g45g", INFO(0xc2201b, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "mx25l1633e", INFO(0xc22415, 0, 64 * 1024, 32, SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES | SECT_4K) },
+#endif
+
+#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
+ /* Micron */
+ { "n25q016a", INFO(0x20bb15, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
+ { "n25q032a", INFO(0x20bb16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
+ { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q064a", INFO(0x20bb17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "n25q256ax1", INFO(0x20bb19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
+ { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
+ { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
+ { "n25q00a", INFO(0x20bb21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
+ { "mt25qu02g", INFO(0x20bb22, 0, 64 * 1024, 4096, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
+#endif
+#ifdef CONFIG_SPI_FLASH_SPANSION /* SPANSION */
+ /* Spansion/Cypress -- single (large) sector size only, at least
+ * for the chips listed here (without boot sectors).
+ */
+ { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR) },
+ { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl512s", INFO6(0x010220, 0x4d0081, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl512s_256k", INFO(0x010220, 0x4d00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl512s_64k", INFO(0x010220, 0x4d01, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl512s_512k", INFO(0x010220, 0x4f00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
+ { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
+ { "s25fl128s", INFO6(0x012018, 0x4d0180, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
+ { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
+ { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) },
+ { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) },
+ { "s25fl116k", INFO(0x014015, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "s25fl164k", INFO(0x014017, 0, 64 * 1024, 128, SECT_4K) },
+ { "s25fl208k", INFO(0x014014, 0, 64 * 1024, 16, SECT_4K | SPI_NOR_DUAL_READ) },
+ { "s25fl128l", INFO(0x016018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+#endif
+#ifdef CONFIG_SPI_FLASH_SST /* SST */
+ /* SST -- large erase sizes are "overlays", "sectors" are 4K */
+ { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
+ { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
+ { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K | SST_WRITE) },
+ { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K | SST_WRITE) },
+ { "sst25vf064c", INFO(0xbf254b, 0, 64 * 1024, 128, SECT_4K) },
+ { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1, SECT_4K | SST_WRITE) },
+ { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2, SECT_4K | SST_WRITE) },
+ { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4, SECT_4K | SST_WRITE) },
+ { "sst25wf020a", INFO(0x621612, 0, 64 * 1024, 4, SECT_4K) },
+ { "sst25wf040b", INFO(0x621613, 0, 64 * 1024, 8, SECT_4K) },
+ { "sst25wf040", INFO(0xbf2504, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
+ { "sst25wf080", INFO(0xbf2505, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
+ { "sst26vf064b", INFO(0xbf2643, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "sst26wf016", INFO(0xbf2651, 0, 64 * 1024, 32, SECT_4K) },
+ { "sst26wf032", INFO(0xbf2622, 0, 64 * 1024, 64, SECT_4K) },
+ { "sst26wf064", INFO(0xbf2643, 0, 64 * 1024, 128, SECT_4K) },
+#endif
+#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
+ /* ST Microelectronics -- newer production may have feature updates */
+ { "m25p10", INFO(0x202011, 0, 32 * 1024, 4, 0) },
+ { "m25p20", INFO(0x202012, 0, 64 * 1024, 4, 0) },
+ { "m25p40", INFO(0x202013, 0, 64 * 1024, 8, 0) },
+ { "m25p80", INFO(0x202014, 0, 64 * 1024, 16, 0) },
+ { "m25p16", INFO(0x202015, 0, 64 * 1024, 32, 0) },
+ { "m25p32", INFO(0x202016, 0, 64 * 1024, 64, 0) },
+ { "m25p64", INFO(0x202017, 0, 64 * 1024, 128, 0) },
+ { "m25p128", INFO(0x202018, 0, 256 * 1024, 64, 0) },
+ { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) },
+ { "m25px16", INFO(0x207115, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "m25px64", INFO(0x207117, 0, 64 * 1024, 128, 0) },
+#endif
+#ifdef CONFIG_SPI_FLASH_WINBOND /* WINBOND */
+ /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
+ { "w25x05", INFO(0xef3010, 0, 64 * 1024, 1, SECT_4K) },
+ { "w25x10", INFO(0xef3011, 0, 64 * 1024, 2, SECT_4K) },
+ { "w25x20", INFO(0xef3012, 0, 64 * 1024, 4, SECT_4K) },
+ { "w25x40", INFO(0xef3013, 0, 64 * 1024, 8, SECT_4K) },
+ { "w25x80", INFO(0xef3014, 0, 64 * 1024, 16, SECT_4K) },
+ { "w25x16", INFO(0xef3015, 0, 64 * 1024, 32, SECT_4K) },
+ {
+ "w25q16dw", INFO(0xef6015, 0, 64 * 1024, 32,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ { "w25x32", INFO(0xef3016, 0, 64 * 1024, 64, SECT_4K) },
+ { "w25q20cl", INFO(0xef4012, 0, 64 * 1024, 4, SECT_4K) },
+ { "w25q20bw", INFO(0xef5012, 0, 64 * 1024, 4, SECT_4K) },
+ { "w25q20ew", INFO(0xef6012, 0, 64 * 1024, 4, SECT_4K) },
+ { "w25q32", INFO(0xef4016, 0, 64 * 1024, 64, SECT_4K) },
+ {
+ "w25q32dw", INFO(0xef6016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ "w25q32jv", INFO(0xef7016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
+ { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
+ {
+ "w25q64dw", INFO(0xef6017, 0, 64 * 1024, 128,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ "w25q128fw", INFO(0xef6018, 0, 64 * 1024, 256,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) },
+ { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) },
+ { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) },
+ { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024,
+ SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ) },
+#endif
+#ifdef CONFIG_SPI_FLASH_XMC
+ /* XMC (Wuhan Xinxin Semiconductor Manufacturing Corp.) */
+ { "XM25QH64A", INFO(0x207017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "XM25QH128A", INFO(0x207018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+#endif
+ { },
+};
+
+static const struct flash_info *spi_nor_read_id(struct spi_nor *nor)
+{
+ int tmp;
+ u8 id[SPI_NOR_MAX_ID_LEN];
+ const struct flash_info *info;
+
+ if (!ARRAY_SIZE(spi_nor_ids))
+ return ERR_PTR(-ENODEV);
+
+ tmp = nor->read_reg(nor, SPINOR_OP_RDID, id, SPI_NOR_MAX_ID_LEN);
+ if (tmp < 0) {
+ dev_dbg(nor->dev, "error %d reading JEDEC ID\n", tmp);
+ return ERR_PTR(tmp);
+ }
+
+ for (tmp = 0; tmp < ARRAY_SIZE(spi_nor_ids) - 1; tmp++) {
+ info = &spi_nor_ids[tmp];
+ if (info->id_len) {
+ if (!memcmp(info->id, id, info->id_len))
+ return &spi_nor_ids[tmp];
+ }
+ }
+ dev_err(nor->dev, "unrecognized JEDEC id bytes: %02x, %02x, %02x\n",
+ id[0], id[1], id[2]);
+ return ERR_PTR(-ENODEV);
+}
+
+static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ int ret;
+
+ dev_dbg(nor->dev, "from 0x%08x, len %zd\n", (u32)from, len);
+
+ while (len) {
+ loff_t addr = from;
+
+ ret = nor->read(nor, addr, len, buf);
+ if (ret == 0) {
+ /* We shouldn't see 0-length reads */
+ ret = -EIO;
+ goto read_err;
+ }
+ if (ret < 0)
+ goto read_err;
+
+ *retlen += ret;
+ buf += ret;
+ from += ret;
+ len -= ret;
+ }
+ ret = 0;
+
+read_err:
+ return ret;
+}
+
+#ifdef CONFIG_SPI_FLASH_SST
+static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ size_t actual;
+ int ret;
+
+ dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+
+ write_enable(nor);
+
+ nor->sst_write_second = false;
+
+ actual = to % 2;
+ /* Start write from odd address. */
+ if (actual) {
+ nor->program_opcode = SPINOR_OP_BP;
+
+ /* write one byte. */
+ ret = nor->write(nor, to, 1, buf);
+ if (ret < 0)
+ goto sst_write_err;
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto sst_write_err;
+ }
+ to += actual;
+
+ /* Write out most of the data here. */
+ for (; actual < len - 1; actual += 2) {
+ nor->program_opcode = SPINOR_OP_AAI_WP;
+
+ /* write two bytes. */
+ ret = nor->write(nor, to, 2, buf + actual);
+ if (ret < 0)
+ goto sst_write_err;
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto sst_write_err;
+ to += 2;
+ nor->sst_write_second = true;
+ }
+ nor->sst_write_second = false;
+
+ write_disable(nor);
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto sst_write_err;
+
+ /* Write out trailing byte if it exists. */
+ if (actual != len) {
+ write_enable(nor);
+
+ nor->program_opcode = SPINOR_OP_BP;
+ ret = nor->write(nor, to, 1, buf + actual);
+ if (ret < 0)
+ goto sst_write_err;
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto sst_write_err;
+ write_disable(nor);
+ actual += 1;
+ }
+sst_write_err:
+ *retlen += actual;
+ return ret;
+}
+#endif
+/*
+ * Write an address range to the nor chip. Data must be written in
+ * FLASH_PAGESIZE chunks. The address range may be any size provided
+ * it is within the physical boundaries.
+ */
+static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ size_t page_offset, page_remain, i;
+ ssize_t ret;
+
+ dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+
+ for (i = 0; i < len; ) {
+ ssize_t written;
+ loff_t addr = to + i;
+
+ /*
+ * If page_size is a power of two, the offset can be quickly
+ * calculated with an AND operation. On the other cases we
+ * need to do a modulus operation (more expensive).
+ * Power of two numbers have only one bit set and we can use
+ * the instruction hweight32 to detect if we need to do a
+ * modulus (do_div()) or not.
+ */
+ if (hweight32(nor->page_size) == 1) {
+ page_offset = addr & (nor->page_size - 1);
+ } else {
+ u64 aux = addr;
+
+ page_offset = do_div(aux, nor->page_size);
+ }
+ /* the size of data remaining on the first page */
+ page_remain = min_t(size_t,
+ nor->page_size - page_offset, len - i);
+
+ write_enable(nor);
+ ret = nor->write(nor, addr, page_remain, buf + i);
+ if (ret < 0)
+ goto write_err;
+ written = ret;
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto write_err;
+ *retlen += written;
+ i += written;
+ if (written != page_remain) {
+ ret = -EIO;
+ goto write_err;
+ }
+ }
+
+write_err:
+ return ret;
+}
+
+#ifdef CONFIG_SPI_FLASH_MACRONIX
+/**
+ * macronix_quad_enable() - set QE bit in Status Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Status Register.
+ *
+ * bit 6 of the Status Register is the QE bit for Macronix like QSPI memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int macronix_quad_enable(struct spi_nor *nor)
+{
+ int ret, val;
+
+ val = read_sr(nor);
+ if (val < 0)
+ return val;
+ if (val & SR_QUAD_EN_MX)
+ return 0;
+
+ write_enable(nor);
+
+ write_sr(nor, val | SR_QUAD_EN_MX);
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ return ret;
+
+ ret = read_sr(nor);
+ if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) {
+ dev_err(nor->dev, "Macronix Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+/*
+ * Write status Register and configuration register with 2 bytes
+ * The first byte will be written to the status register, while the
+ * second byte will be written to the configuration register.
+ * Return negative if error occurred.
+ */
+static int write_sr_cr(struct spi_nor *nor, u8 *sr_cr)
+{
+ int ret;
+
+ write_enable(nor);
+
+ ret = nor->write_reg(nor, SPINOR_OP_WRSR, sr_cr, 2);
+ if (ret < 0) {
+ dev_dbg(nor->dev,
+ "error while writing configuration register\n");
+ return -EINVAL;
+ }
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret) {
+ dev_dbg(nor->dev,
+ "timeout while writing configuration register\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+/**
+ * spansion_read_cr_quad_enable() - set QE bit in Configuration Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Configuration Register.
+ * This function should be used with QSPI memories supporting the Read
+ * Configuration Register (35h) instruction.
+ *
+ * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
+ * memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spansion_read_cr_quad_enable(struct spi_nor *nor)
+{
+ u8 sr_cr[2];
+ int ret;
+
+ /* Check current Quad Enable bit value. */
+ ret = read_cr(nor);
+ if (ret < 0) {
+ dev_dbg(dev, "error while reading configuration register\n");
+ return -EINVAL;
+ }
+
+ if (ret & CR_QUAD_EN_SPAN)
+ return 0;
+
+ sr_cr[1] = ret | CR_QUAD_EN_SPAN;
+
+ /* Keep the current value of the Status Register. */
+ ret = read_sr(nor);
+ if (ret < 0) {
+ dev_dbg(dev, "error while reading status register\n");
+ return -EINVAL;
+ }
+ sr_cr[0] = ret;
+
+ ret = write_sr_cr(nor, sr_cr);
+ if (ret)
+ return ret;
+
+ /* Read back and check it. */
+ ret = read_cr(nor);
+ if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) {
+ dev_dbg(nor->dev, "Spansion Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+#if CONFIG_IS_ENABLED(SPI_FLASH_SFDP_SUPPORT)
+/**
+ * spansion_no_read_cr_quad_enable() - set QE bit in Configuration Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Configuration Register.
+ * This function should be used with QSPI memories not supporting the Read
+ * Configuration Register (35h) instruction.
+ *
+ * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
+ * memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spansion_no_read_cr_quad_enable(struct spi_nor *nor)
+{
+ u8 sr_cr[2];
+ int ret;
+
+ /* Keep the current value of the Status Register. */
+ ret = read_sr(nor);
+ if (ret < 0) {
+ dev_dbg(nor->dev, "error while reading status register\n");
+ return -EINVAL;
+ }
+ sr_cr[0] = ret;
+ sr_cr[1] = CR_QUAD_EN_SPAN;
+
+ return write_sr_cr(nor, sr_cr);
+}
+
+#endif /* CONFIG_SPI_FLASH_SFDP_SUPPORT */
+#endif /* CONFIG_SPI_FLASH_SPANSION */
+
+struct spi_nor_read_command {
+ u8 num_mode_clocks;
+ u8 num_wait_states;
+ u8 opcode;
+ enum spi_nor_protocol proto;
+};
+
+struct spi_nor_pp_command {
+ u8 opcode;
+ enum spi_nor_protocol proto;
+};
+
+enum spi_nor_read_command_index {
+ SNOR_CMD_READ,
+ SNOR_CMD_READ_FAST,
+ SNOR_CMD_READ_1_1_1_DTR,
+
+ /* Dual SPI */
+ SNOR_CMD_READ_1_1_2,
+ SNOR_CMD_READ_1_2_2,
+ SNOR_CMD_READ_2_2_2,
+ SNOR_CMD_READ_1_2_2_DTR,
+
+ /* Quad SPI */
+ SNOR_CMD_READ_1_1_4,
+ SNOR_CMD_READ_1_4_4,
+ SNOR_CMD_READ_4_4_4,
+ SNOR_CMD_READ_1_4_4_DTR,
+
+ /* Octo SPI */
+ SNOR_CMD_READ_1_1_8,
+ SNOR_CMD_READ_1_8_8,
+ SNOR_CMD_READ_8_8_8,
+ SNOR_CMD_READ_1_8_8_DTR,
+
+ SNOR_CMD_READ_MAX
+};
+
+enum spi_nor_pp_command_index {
+ SNOR_CMD_PP,
+
+ /* Quad SPI */
+ SNOR_CMD_PP_1_1_4,
+ SNOR_CMD_PP_1_4_4,
+ SNOR_CMD_PP_4_4_4,
+
+ /* Octo SPI */
+ SNOR_CMD_PP_1_1_8,
+ SNOR_CMD_PP_1_8_8,
+ SNOR_CMD_PP_8_8_8,
+
+ SNOR_CMD_PP_MAX
+};
+
+struct spi_nor_flash_parameter {
+ u64 size;
+ u32 page_size;
+
+ struct spi_nor_hwcaps hwcaps;
+ struct spi_nor_read_command reads[SNOR_CMD_READ_MAX];
+ struct spi_nor_pp_command page_programs[SNOR_CMD_PP_MAX];
+
+ int (*quad_enable)(struct spi_nor *nor);
+};
+
+static void
+spi_nor_set_read_settings(struct spi_nor_read_command *read,
+ u8 num_mode_clocks,
+ u8 num_wait_states,
+ u8 opcode,
+ enum spi_nor_protocol proto)
+{
+ read->num_mode_clocks = num_mode_clocks;
+ read->num_wait_states = num_wait_states;
+ read->opcode = opcode;
+ read->proto = proto;
+}
+
+static void
+spi_nor_set_pp_settings(struct spi_nor_pp_command *pp,
+ u8 opcode,
+ enum spi_nor_protocol proto)
+{
+ pp->opcode = opcode;
+ pp->proto = proto;
+}
+
+#if CONFIG_IS_ENABLED(SPI_FLASH_SFDP_SUPPORT)
+/*
+ * Serial Flash Discoverable Parameters (SFDP) parsing.
+ */
+
+/**
+ * spi_nor_read_sfdp() - read Serial Flash Discoverable Parameters.
+ * @nor: pointer to a 'struct spi_nor'
+ * @addr: offset in the SFDP area to start reading data from
+ * @len: number of bytes to read
+ * @buf: buffer where the SFDP data are copied into (dma-safe memory)
+ *
+ * Whatever the actual numbers of bytes for address and dummy cycles are
+ * for (Fast) Read commands, the Read SFDP (5Ah) instruction is always
+ * followed by a 3-byte address and 8 dummy clock cycles.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr,
+ size_t len, void *buf)
+{
+ u8 addr_width, read_opcode, read_dummy;
+ int ret;
+
+ read_opcode = nor->read_opcode;
+ addr_width = nor->addr_width;
+ read_dummy = nor->read_dummy;
+
+ nor->read_opcode = SPINOR_OP_RDSFDP;
+ nor->addr_width = 3;
+ nor->read_dummy = 8;
+
+ while (len) {
+ ret = nor->read(nor, addr, len, (u8 *)buf);
+ if (!ret || ret > len) {
+ ret = -EIO;
+ goto read_err;
+ }
+ if (ret < 0)
+ goto read_err;
+
+ buf += ret;
+ addr += ret;
+ len -= ret;
+ }
+ ret = 0;
+
+read_err:
+ nor->read_opcode = read_opcode;
+ nor->addr_width = addr_width;
+ nor->read_dummy = read_dummy;
+
+ return ret;
+}
+
+struct sfdp_parameter_header {
+ u8 id_lsb;
+ u8 minor;
+ u8 major;
+ u8 length; /* in double words */
+ u8 parameter_table_pointer[3]; /* byte address */
+ u8 id_msb;
+};
+
+#define SFDP_PARAM_HEADER_ID(p) (((p)->id_msb << 8) | (p)->id_lsb)
+#define SFDP_PARAM_HEADER_PTP(p) \
+ (((p)->parameter_table_pointer[2] << 16) | \
+ ((p)->parameter_table_pointer[1] << 8) | \
+ ((p)->parameter_table_pointer[0] << 0))
+
+#define SFDP_BFPT_ID 0xff00 /* Basic Flash Parameter Table */
+#define SFDP_SECTOR_MAP_ID 0xff81 /* Sector Map Table */
+
+#define SFDP_SIGNATURE 0x50444653U
+#define SFDP_JESD216_MAJOR 1
+#define SFDP_JESD216_MINOR 0
+#define SFDP_JESD216A_MINOR 5
+#define SFDP_JESD216B_MINOR 6
+
+struct sfdp_header {
+ u32 signature; /* Ox50444653U <=> "SFDP" */
+ u8 minor;
+ u8 major;
+ u8 nph; /* 0-base number of parameter headers */
+ u8 unused;
+
+ /* Basic Flash Parameter Table. */
+ struct sfdp_parameter_header bfpt_header;
+};
+
+/* Basic Flash Parameter Table */
+
+/*
+ * JESD216 rev B defines a Basic Flash Parameter Table of 16 DWORDs.
+ * They are indexed from 1 but C arrays are indexed from 0.
+ */
+#define BFPT_DWORD(i) ((i) - 1)
+#define BFPT_DWORD_MAX 16
+
+/* The first version of JESB216 defined only 9 DWORDs. */
+#define BFPT_DWORD_MAX_JESD216 9
+
+/* 1st DWORD. */
+#define BFPT_DWORD1_FAST_READ_1_1_2 BIT(16)
+#define BFPT_DWORD1_ADDRESS_BYTES_MASK GENMASK(18, 17)
+#define BFPT_DWORD1_ADDRESS_BYTES_3_ONLY (0x0UL << 17)
+#define BFPT_DWORD1_ADDRESS_BYTES_3_OR_4 (0x1UL << 17)
+#define BFPT_DWORD1_ADDRESS_BYTES_4_ONLY (0x2UL << 17)
+#define BFPT_DWORD1_DTR BIT(19)
+#define BFPT_DWORD1_FAST_READ_1_2_2 BIT(20)
+#define BFPT_DWORD1_FAST_READ_1_4_4 BIT(21)
+#define BFPT_DWORD1_FAST_READ_1_1_4 BIT(22)
+
+/* 5th DWORD. */
+#define BFPT_DWORD5_FAST_READ_2_2_2 BIT(0)
+#define BFPT_DWORD5_FAST_READ_4_4_4 BIT(4)
+
+/* 11th DWORD. */
+#define BFPT_DWORD11_PAGE_SIZE_SHIFT 4
+#define BFPT_DWORD11_PAGE_SIZE_MASK GENMASK(7, 4)
+
+/* 15th DWORD. */
+
+/*
+ * (from JESD216 rev B)
+ * Quad Enable Requirements (QER):
+ * - 000b: Device does not have a QE bit. Device detects 1-1-4 and 1-4-4
+ * reads based on instruction. DQ3/HOLD# functions are hold during
+ * instruction phase.
+ * - 001b: QE is bit 1 of status register 2. It is set via Write Status with
+ * two data bytes where bit 1 of the second byte is one.
+ * [...]
+ * Writing only one byte to the status register has the side-effect of
+ * clearing status register 2, including the QE bit. The 100b code is
+ * used if writing one byte to the status register does not modify
+ * status register 2.
+ * - 010b: QE is bit 6 of status register 1. It is set via Write Status with
+ * one data byte where bit 6 is one.
+ * [...]
+ * - 011b: QE is bit 7 of status register 2. It is set via Write status
+ * register 2 instruction 3Eh with one data byte where bit 7 is one.
+ * [...]
+ * The status register 2 is read using instruction 3Fh.
+ * - 100b: QE is bit 1 of status register 2. It is set via Write Status with
+ * two data bytes where bit 1 of the second byte is one.
+ * [...]
+ * In contrast to the 001b code, writing one byte to the status
+ * register does not modify status register 2.
+ * - 101b: QE is bit 1 of status register 2. Status register 1 is read using
+ * Read Status instruction 05h. Status register2 is read using
+ * instruction 35h. QE is set via Writ Status instruction 01h with
+ * two data bytes where bit 1 of the second byte is one.
+ * [...]
+ */
+#define BFPT_DWORD15_QER_MASK GENMASK(22, 20)
+#define BFPT_DWORD15_QER_NONE (0x0UL << 20) /* Micron */
+#define BFPT_DWORD15_QER_SR2_BIT1_BUGGY (0x1UL << 20)
+#define BFPT_DWORD15_QER_SR1_BIT6 (0x2UL << 20) /* Macronix */
+#define BFPT_DWORD15_QER_SR2_BIT7 (0x3UL << 20)
+#define BFPT_DWORD15_QER_SR2_BIT1_NO_RD (0x4UL << 20)
+#define BFPT_DWORD15_QER_SR2_BIT1 (0x5UL << 20) /* Spansion */
+
+struct sfdp_bfpt {
+ u32 dwords[BFPT_DWORD_MAX];
+};
+
+/* Fast Read settings. */
+
+static void
+spi_nor_set_read_settings_from_bfpt(struct spi_nor_read_command *read,
+ u16 half,
+ enum spi_nor_protocol proto)
+{
+ read->num_mode_clocks = (half >> 5) & 0x07;
+ read->num_wait_states = (half >> 0) & 0x1f;
+ read->opcode = (half >> 8) & 0xff;
+ read->proto = proto;
+}
+
+struct sfdp_bfpt_read {
+ /* The Fast Read x-y-z hardware capability in params->hwcaps.mask. */
+ u32 hwcaps;
+
+ /*
+ * The <supported_bit> bit in <supported_dword> BFPT DWORD tells us
+ * whether the Fast Read x-y-z command is supported.
+ */
+ u32 supported_dword;
+ u32 supported_bit;
+
+ /*
+ * The half-word at offset <setting_shift> in <setting_dword> BFPT DWORD
+ * encodes the op code, the number of mode clocks and the number of wait
+ * states to be used by Fast Read x-y-z command.
+ */
+ u32 settings_dword;
+ u32 settings_shift;
+
+ /* The SPI protocol for this Fast Read x-y-z command. */
+ enum spi_nor_protocol proto;
+};
+
+static const struct sfdp_bfpt_read sfdp_bfpt_reads[] = {
+ /* Fast Read 1-1-2 */
+ {
+ SNOR_HWCAPS_READ_1_1_2,
+ BFPT_DWORD(1), BIT(16), /* Supported bit */
+ BFPT_DWORD(4), 0, /* Settings */
+ SNOR_PROTO_1_1_2,
+ },
+
+ /* Fast Read 1-2-2 */
+ {
+ SNOR_HWCAPS_READ_1_2_2,
+ BFPT_DWORD(1), BIT(20), /* Supported bit */
+ BFPT_DWORD(4), 16, /* Settings */
+ SNOR_PROTO_1_2_2,
+ },
+
+ /* Fast Read 2-2-2 */
+ {
+ SNOR_HWCAPS_READ_2_2_2,
+ BFPT_DWORD(5), BIT(0), /* Supported bit */
+ BFPT_DWORD(6), 16, /* Settings */
+ SNOR_PROTO_2_2_2,
+ },
+
+ /* Fast Read 1-1-4 */
+ {
+ SNOR_HWCAPS_READ_1_1_4,
+ BFPT_DWORD(1), BIT(22), /* Supported bit */
+ BFPT_DWORD(3), 16, /* Settings */
+ SNOR_PROTO_1_1_4,
+ },
+
+ /* Fast Read 1-4-4 */
+ {
+ SNOR_HWCAPS_READ_1_4_4,
+ BFPT_DWORD(1), BIT(21), /* Supported bit */
+ BFPT_DWORD(3), 0, /* Settings */
+ SNOR_PROTO_1_4_4,
+ },
+
+ /* Fast Read 4-4-4 */
+ {
+ SNOR_HWCAPS_READ_4_4_4,
+ BFPT_DWORD(5), BIT(4), /* Supported bit */
+ BFPT_DWORD(7), 16, /* Settings */
+ SNOR_PROTO_4_4_4,
+ },
+};
+
+struct sfdp_bfpt_erase {
+ /*
+ * The half-word at offset <shift> in DWORD <dwoard> encodes the
+ * op code and erase sector size to be used by Sector Erase commands.
+ */
+ u32 dword;
+ u32 shift;
+};
+
+static const struct sfdp_bfpt_erase sfdp_bfpt_erases[] = {
+ /* Erase Type 1 in DWORD8 bits[15:0] */
+ {BFPT_DWORD(8), 0},
+
+ /* Erase Type 2 in DWORD8 bits[31:16] */
+ {BFPT_DWORD(8), 16},
+
+ /* Erase Type 3 in DWORD9 bits[15:0] */
+ {BFPT_DWORD(9), 0},
+
+ /* Erase Type 4 in DWORD9 bits[31:16] */
+ {BFPT_DWORD(9), 16},
+};
+
+static int spi_nor_hwcaps_read2cmd(u32 hwcaps);
+
+/**
+ * spi_nor_parse_bfpt() - read and parse the Basic Flash Parameter Table.
+ * @nor: pointer to a 'struct spi_nor'
+ * @bfpt_header: pointer to the 'struct sfdp_parameter_header' describing
+ * the Basic Flash Parameter Table length and version
+ * @params: pointer to the 'struct spi_nor_flash_parameter' to be
+ * filled
+ *
+ * The Basic Flash Parameter Table is the main and only mandatory table as
+ * defined by the SFDP (JESD216) specification.
+ * It provides us with the total size (memory density) of the data array and
+ * the number of address bytes for Fast Read, Page Program and Sector Erase
+ * commands.
+ * For Fast READ commands, it also gives the number of mode clock cycles and
+ * wait states (regrouped in the number of dummy clock cycles) for each
+ * supported instruction op code.
+ * For Page Program, the page size is now available since JESD216 rev A, however
+ * the supported instruction op codes are still not provided.
+ * For Sector Erase commands, this table stores the supported instruction op
+ * codes and the associated sector sizes.
+ * Finally, the Quad Enable Requirements (QER) are also available since JESD216
+ * rev A. The QER bits encode the manufacturer dependent procedure to be
+ * executed to set the Quad Enable (QE) bit in some internal register of the
+ * Quad SPI memory. Indeed the QE bit, when it exists, must be set before
+ * sending any Quad SPI command to the memory. Actually, setting the QE bit
+ * tells the memory to reassign its WP# and HOLD#/RESET# pins to functions IO2
+ * and IO3 hence enabling 4 (Quad) I/O lines.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_parse_bfpt(struct spi_nor *nor,
+ const struct sfdp_parameter_header *bfpt_header,
+ struct spi_nor_flash_parameter *params)
+{
+ struct mtd_info *mtd = &nor->mtd;
+ struct sfdp_bfpt bfpt;
+ size_t len;
+ int i, cmd, err;
+ u32 addr;
+ u16 half;
+
+ /* JESD216 Basic Flash Parameter Table length is at least 9 DWORDs. */
+ if (bfpt_header->length < BFPT_DWORD_MAX_JESD216)
+ return -EINVAL;
+
+ /* Read the Basic Flash Parameter Table. */
+ len = min_t(size_t, sizeof(bfpt),
+ bfpt_header->length * sizeof(u32));
+ addr = SFDP_PARAM_HEADER_PTP(bfpt_header);
+ memset(&bfpt, 0, sizeof(bfpt));
+ err = spi_nor_read_sfdp(nor, addr, len, &bfpt);
+ if (err < 0)
+ return err;
+
+ /* Fix endianness of the BFPT DWORDs. */
+ for (i = 0; i < BFPT_DWORD_MAX; i++)
+ bfpt.dwords[i] = le32_to_cpu(bfpt.dwords[i]);
+
+ /* Number of address bytes. */
+ switch (bfpt.dwords[BFPT_DWORD(1)] & BFPT_DWORD1_ADDRESS_BYTES_MASK) {
+ case BFPT_DWORD1_ADDRESS_BYTES_3_ONLY:
+ nor->addr_width = 3;
+ break;
+
+ case BFPT_DWORD1_ADDRESS_BYTES_4_ONLY:
+ nor->addr_width = 4;
+ break;
+
+ default:
+ break;
+ }
+
+ /* Flash Memory Density (in bits). */
+ params->size = bfpt.dwords[BFPT_DWORD(2)];
+ if (params->size & BIT(31)) {
+ params->size &= ~BIT(31);
+
+ /*
+ * Prevent overflows on params->size. Anyway, a NOR of 2^64
+ * bits is unlikely to exist so this error probably means
+ * the BFPT we are reading is corrupted/wrong.
+ */
+ if (params->size > 63)
+ return -EINVAL;
+
+ params->size = 1ULL << params->size;
+ } else {
+ params->size++;
+ }
+ params->size >>= 3; /* Convert to bytes. */
+
+ /* Fast Read settings. */
+ for (i = 0; i < ARRAY_SIZE(sfdp_bfpt_reads); i++) {
+ const struct sfdp_bfpt_read *rd = &sfdp_bfpt_reads[i];
+ struct spi_nor_read_command *read;
+
+ if (!(bfpt.dwords[rd->supported_dword] & rd->supported_bit)) {
+ params->hwcaps.mask &= ~rd->hwcaps;
+ continue;
+ }
+
+ params->hwcaps.mask |= rd->hwcaps;
+ cmd = spi_nor_hwcaps_read2cmd(rd->hwcaps);
+ read = ¶ms->reads[cmd];
+ half = bfpt.dwords[rd->settings_dword] >> rd->settings_shift;
+ spi_nor_set_read_settings_from_bfpt(read, half, rd->proto);
+ }
+
+ /* Sector Erase settings. */
+ for (i = 0; i < ARRAY_SIZE(sfdp_bfpt_erases); i++) {
+ const struct sfdp_bfpt_erase *er = &sfdp_bfpt_erases[i];
+ u32 erasesize;
+ u8 opcode;
+
+ half = bfpt.dwords[er->dword] >> er->shift;
+ erasesize = half & 0xff;
+
+ /* erasesize == 0 means this Erase Type is not supported. */
+ if (!erasesize)
+ continue;
+
+ erasesize = 1U << erasesize;
+ opcode = (half >> 8) & 0xff;
+#ifdef CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
+ if (erasesize == SZ_4K) {
+ nor->erase_opcode = opcode;
+ mtd->erasesize = erasesize;
+ break;
+ }
+#endif
+ if (!mtd->erasesize || mtd->erasesize < erasesize) {
+ nor->erase_opcode = opcode;
+ mtd->erasesize = erasesize;
+ }
+ }
+
+ /* Stop here if not JESD216 rev A or later. */
+ if (bfpt_header->length < BFPT_DWORD_MAX)
+ return 0;
+
+ /* Page size: this field specifies 'N' so the page size = 2^N bytes. */
+ params->page_size = bfpt.dwords[BFPT_DWORD(11)];
+ params->page_size &= BFPT_DWORD11_PAGE_SIZE_MASK;
+ params->page_size >>= BFPT_DWORD11_PAGE_SIZE_SHIFT;
+ params->page_size = 1U << params->page_size;
+
+ /* Quad Enable Requirements. */
+ switch (bfpt.dwords[BFPT_DWORD(15)] & BFPT_DWORD15_QER_MASK) {
+ case BFPT_DWORD15_QER_NONE:
+ params->quad_enable = NULL;
+ break;
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+ case BFPT_DWORD15_QER_SR2_BIT1_BUGGY:
+ case BFPT_DWORD15_QER_SR2_BIT1_NO_RD:
+ params->quad_enable = spansion_no_read_cr_quad_enable;
+ break;
+#endif
+#ifdef CONFIG_SPI_FLASH_MACRONIX
+ case BFPT_DWORD15_QER_SR1_BIT6:
+ params->quad_enable = macronix_quad_enable;
+ break;
+#endif
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+ case BFPT_DWORD15_QER_SR2_BIT1:
+ params->quad_enable = spansion_read_cr_quad_enable;
+ break;
+#endif
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * spi_nor_parse_sfdp() - parse the Serial Flash Discoverable Parameters.
+ * @nor: pointer to a 'struct spi_nor'
+ * @params: pointer to the 'struct spi_nor_flash_parameter' to be
+ * filled
+ *
+ * The Serial Flash Discoverable Parameters are described by the JEDEC JESD216
+ * specification. This is a standard which tends to supported by almost all
+ * (Q)SPI memory manufacturers. Those hard-coded tables allow us to learn at
+ * runtime the main parameters needed to perform basic SPI flash operations such
+ * as Fast Read, Page Program or Sector Erase commands.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_parse_sfdp(struct spi_nor *nor,
+ struct spi_nor_flash_parameter *params)
+{
+ const struct sfdp_parameter_header *param_header, *bfpt_header;
+ struct sfdp_parameter_header *param_headers = NULL;
+ struct sfdp_header header;
+ size_t psize;
+ int i, err;
+
+ /* Get the SFDP header. */
+ err = spi_nor_read_sfdp(nor, 0, sizeof(header), &header);
+ if (err < 0)
+ return err;
+
+ /* Check the SFDP header version. */
+ if (le32_to_cpu(header.signature) != SFDP_SIGNATURE ||
+ header.major != SFDP_JESD216_MAJOR)
+ return -EINVAL;
+
+ /*
+ * Verify that the first and only mandatory parameter header is a
+ * Basic Flash Parameter Table header as specified in JESD216.
+ */
+ bfpt_header = &header.bfpt_header;
+ if (SFDP_PARAM_HEADER_ID(bfpt_header) != SFDP_BFPT_ID ||
+ bfpt_header->major != SFDP_JESD216_MAJOR)
+ return -EINVAL;
+
+ /*
+ * Allocate memory then read all parameter headers with a single
+ * Read SFDP command. These parameter headers will actually be parsed
+ * twice: a first time to get the latest revision of the basic flash
+ * parameter table, then a second time to handle the supported optional
+ * tables.
+ * Hence we read the parameter headers once for all to reduce the
+ * processing time. Also we use kmalloc() instead of devm_kmalloc()
+ * because we don't need to keep these parameter headers: the allocated
+ * memory is always released with kfree() before exiting this function.
+ */
+ if (header.nph) {
+ psize = header.nph * sizeof(*param_headers);
+
+ param_headers = kmalloc(psize, GFP_KERNEL);
+ if (!param_headers)
+ return -ENOMEM;
+
+ err = spi_nor_read_sfdp(nor, sizeof(header),
+ psize, param_headers);
+ if (err < 0) {
+ dev_err(dev, "failed to read SFDP parameter headers\n");
+ goto exit;
+ }
+ }
+
+ /*
+ * Check other parameter headers to get the latest revision of
+ * the basic flash parameter table.
+ */
+ for (i = 0; i < header.nph; i++) {
+ param_header = ¶m_headers[i];
+
+ if (SFDP_PARAM_HEADER_ID(param_header) == SFDP_BFPT_ID &&
+ param_header->major == SFDP_JESD216_MAJOR &&
+ (param_header->minor > bfpt_header->minor ||
+ (param_header->minor == bfpt_header->minor &&
+ param_header->length > bfpt_header->length)))
+ bfpt_header = param_header;
+ }
+
+ err = spi_nor_parse_bfpt(nor, bfpt_header, params);
+ if (err)
+ goto exit;
+
+ /* Parse other parameter headers. */
+ for (i = 0; i < header.nph; i++) {
+ param_header = ¶m_headers[i];
+
+ switch (SFDP_PARAM_HEADER_ID(param_header)) {
+ case SFDP_SECTOR_MAP_ID:
+ dev_info(dev, "non-uniform erase sector maps are not supported yet.\n");
+ break;
+
+ default:
+ break;
+ }
+
+ if (err)
+ goto exit;
+ }
+
+exit:
+ kfree(param_headers);
+ return err;
+}
+#else
+static int spi_nor_parse_sfdp(struct spi_nor *nor,
+ struct spi_nor_flash_parameter *params)
+{
+ return -EINVAL;
+}
+#endif /* SPI_FLASH_SFDP_SUPPORT */
+
+static int spi_nor_init_params(struct spi_nor *nor,
+ const struct flash_info *info,
+ struct spi_nor_flash_parameter *params)
+{
+ /* Set legacy flash parameters as default. */
+ memset(params, 0, sizeof(*params));
+
+ /* Set SPI NOR sizes. */
+ params->size = info->sector_size * info->n_sectors;
+ params->page_size = info->page_size;
+
+ /* (Fast) Read settings. */
+ params->hwcaps.mask |= SNOR_HWCAPS_READ;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ],
+ 0, 0, SPINOR_OP_READ,
+ SNOR_PROTO_1_1_1);
+
+ if (!(info->flags & SPI_NOR_NO_FR)) {
+ params->hwcaps.mask |= SNOR_HWCAPS_READ_FAST;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_FAST],
+ 0, 8, SPINOR_OP_READ_FAST,
+ SNOR_PROTO_1_1_1);
+ }
+
+ if (info->flags & SPI_NOR_DUAL_READ) {
+ params->hwcaps.mask |= SNOR_HWCAPS_READ_1_1_2;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_1_1_2],
+ 0, 8, SPINOR_OP_READ_1_1_2,
+ SNOR_PROTO_1_1_2);
+ }
+
+ if (info->flags & SPI_NOR_QUAD_READ) {
+ params->hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_1_1_4],
+ 0, 8, SPINOR_OP_READ_1_1_4,
+ SNOR_PROTO_1_1_4);
+ }
+
+ /* Page Program settings. */
+ params->hwcaps.mask |= SNOR_HWCAPS_PP;
+ spi_nor_set_pp_settings(¶ms->page_programs[SNOR_CMD_PP],
+ SPINOR_OP_PP, SNOR_PROTO_1_1_1);
+
+ if (info->flags & SPI_NOR_QUAD_READ) {
+ params->hwcaps.mask |= SNOR_HWCAPS_PP_1_1_4;
+ spi_nor_set_pp_settings(¶ms->page_programs[SNOR_CMD_PP_1_1_4],
+ SPINOR_OP_PP_1_1_4, SNOR_PROTO_1_1_4);
+ }
+
+ /* Select the procedure to set the Quad Enable bit. */
+ if (params->hwcaps.mask & (SNOR_HWCAPS_READ_QUAD |
+ SNOR_HWCAPS_PP_QUAD)) {
+ switch (JEDEC_MFR(info)) {
+#ifdef CONFIG_SPI_FLASH_MACRONIX
+ case SNOR_MFR_MACRONIX:
+ params->quad_enable = macronix_quad_enable;
+ break;
+#endif
+ case SNOR_MFR_ST:
+ case SNOR_MFR_MICRON:
+ break;
+
+ default:
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+ /* Kept only for backward compatibility purpose. */
+ params->quad_enable = spansion_read_cr_quad_enable;
+#endif
+ break;
+ }
+ }
+
+ /* Override the parameters with data read from SFDP tables. */
+ nor->addr_width = 0;
+ nor->mtd.erasesize = 0;
+ if ((info->flags & (SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)) &&
+ !(info->flags & SPI_NOR_SKIP_SFDP)) {
+ struct spi_nor_flash_parameter sfdp_params;
+
+ memcpy(&sfdp_params, params, sizeof(sfdp_params));
+ if (spi_nor_parse_sfdp(nor, &sfdp_params)) {
+ nor->addr_width = 0;
+ nor->mtd.erasesize = 0;
+ } else {
+ memcpy(params, &sfdp_params, sizeof(*params));
+ }
+ }
+
+ return 0;
+}
+
+static int spi_nor_hwcaps2cmd(u32 hwcaps, const int table[][2], size_t size)
+{
+ size_t i;
+
+ for (i = 0; i < size; i++)
+ if (table[i][0] == (int)hwcaps)
+ return table[i][1];
+
+ return -EINVAL;
+}
+
+static int spi_nor_hwcaps_read2cmd(u32 hwcaps)
+{
+ static const int hwcaps_read2cmd[][2] = {
+ { SNOR_HWCAPS_READ, SNOR_CMD_READ },
+ { SNOR_HWCAPS_READ_FAST, SNOR_CMD_READ_FAST },
+ { SNOR_HWCAPS_READ_1_1_1_DTR, SNOR_CMD_READ_1_1_1_DTR },
+ { SNOR_HWCAPS_READ_1_1_2, SNOR_CMD_READ_1_1_2 },
+ { SNOR_HWCAPS_READ_1_2_2, SNOR_CMD_READ_1_2_2 },
+ { SNOR_HWCAPS_READ_2_2_2, SNOR_CMD_READ_2_2_2 },
+ { SNOR_HWCAPS_READ_1_2_2_DTR, SNOR_CMD_READ_1_2_2_DTR },
+ { SNOR_HWCAPS_READ_1_1_4, SNOR_CMD_READ_1_1_4 },
+ { SNOR_HWCAPS_READ_1_4_4, SNOR_CMD_READ_1_4_4 },
+ { SNOR_HWCAPS_READ_4_4_4, SNOR_CMD_READ_4_4_4 },
+ { SNOR_HWCAPS_READ_1_4_4_DTR, SNOR_CMD_READ_1_4_4_DTR },
+ { SNOR_HWCAPS_READ_1_1_8, SNOR_CMD_READ_1_1_8 },
+ { SNOR_HWCAPS_READ_1_8_8, SNOR_CMD_READ_1_8_8 },
+ { SNOR_HWCAPS_READ_8_8_8, SNOR_CMD_READ_8_8_8 },
+ { SNOR_HWCAPS_READ_1_8_8_DTR, SNOR_CMD_READ_1_8_8_DTR },
+ };
+
+ return spi_nor_hwcaps2cmd(hwcaps, hwcaps_read2cmd,
+ ARRAY_SIZE(hwcaps_read2cmd));
+}
+
+static int spi_nor_hwcaps_pp2cmd(u32 hwcaps)
+{
+ static const int hwcaps_pp2cmd[][2] = {
+ { SNOR_HWCAPS_PP, SNOR_CMD_PP },
+ { SNOR_HWCAPS_PP_1_1_4, SNOR_CMD_PP_1_1_4 },
+ { SNOR_HWCAPS_PP_1_4_4, SNOR_CMD_PP_1_4_4 },
+ { SNOR_HWCAPS_PP_4_4_4, SNOR_CMD_PP_4_4_4 },
+ { SNOR_HWCAPS_PP_1_1_8, SNOR_CMD_PP_1_1_8 },
+ { SNOR_HWCAPS_PP_1_8_8, SNOR_CMD_PP_1_8_8 },
+ { SNOR_HWCAPS_PP_8_8_8, SNOR_CMD_PP_8_8_8 },
+ };
+
+ return spi_nor_hwcaps2cmd(hwcaps, hwcaps_pp2cmd,
+ ARRAY_SIZE(hwcaps_pp2cmd));
+}
+
+static int spi_nor_select_read(struct spi_nor *nor,
+ const struct spi_nor_flash_parameter *params,
+ u32 shared_hwcaps)
+{
+ int cmd, best_match = fls(shared_hwcaps & SNOR_HWCAPS_READ_MASK) - 1;
+ const struct spi_nor_read_command *read;
+
+ if (best_match < 0)
+ return -EINVAL;
+
+ cmd = spi_nor_hwcaps_read2cmd(BIT(best_match));
+ if (cmd < 0)
+ return -EINVAL;
+
+ read = ¶ms->reads[cmd];
+ nor->read_opcode = read->opcode;
+ nor->read_proto = read->proto;
+
+ /*
+ * In the spi-nor framework, we don't need to make the difference
+ * between mode clock cycles and wait state clock cycles.
+ * Indeed, the value of the mode clock cycles is used by a QSPI
+ * flash memory to know whether it should enter or leave its 0-4-4
+ * (Continuous Read / XIP) mode.
+ * eXecution In Place is out of the scope of the mtd sub-system.
+ * Hence we choose to merge both mode and wait state clock cycles
+ * into the so called dummy clock cycles.
+ */
+ nor->read_dummy = read->num_mode_clocks + read->num_wait_states;
+ return 0;
+}
+
+static int spi_nor_select_pp(struct spi_nor *nor,
+ const struct spi_nor_flash_parameter *params,
+ u32 shared_hwcaps)
+{
+ int cmd, best_match = fls(shared_hwcaps & SNOR_HWCAPS_PP_MASK) - 1;
+ const struct spi_nor_pp_command *pp;
+
+ if (best_match < 0)
+ return -EINVAL;
+
+ cmd = spi_nor_hwcaps_pp2cmd(BIT(best_match));
+ if (cmd < 0)
+ return -EINVAL;
+
+ pp = ¶ms->page_programs[cmd];
+ nor->program_opcode = pp->opcode;
+ nor->write_proto = pp->proto;
+ return 0;
+}
+
+static int spi_nor_select_erase(struct spi_nor *nor,
+ const struct flash_info *info)
+{
+ struct mtd_info *mtd = &nor->mtd;
+
+ /* Do nothing if already configured from SFDP. */
+ if (mtd->erasesize)
+ return 0;
+
+#ifdef CONFIG_SPI_FLASH_USE_4K_SECTORS
+ /* prefer "small sector" erase if possible */
+ if (info->flags & SECT_4K) {
+ nor->erase_opcode = SPINOR_OP_BE_4K;
+ mtd->erasesize = 4096;
+ } else if (info->flags & SECT_4K_PMC) {
+ nor->erase_opcode = SPINOR_OP_BE_4K_PMC;
+ mtd->erasesize = 4096;
+ } else
+#endif
+ {
+ nor->erase_opcode = SPINOR_OP_SE;
+ mtd->erasesize = info->sector_size;
+ }
+ return 0;
+}
+
+static int spi_nor_setup(struct spi_nor *nor, const struct flash_info *info,
+ const struct spi_nor_flash_parameter *params,
+ const struct spi_nor_hwcaps *hwcaps)
+{
+ u32 ignored_mask, shared_mask;
+ bool enable_quad_io;
+ int err;
+
+ /*
+ * Keep only the hardware capabilities supported by both the SPI
+ * controller and the SPI flash memory.
+ */
+ shared_mask = hwcaps->mask & params->hwcaps.mask;
+
+ /* SPI n-n-n protocols are not supported yet. */
+ ignored_mask = (SNOR_HWCAPS_READ_2_2_2 |
+ SNOR_HWCAPS_READ_4_4_4 |
+ SNOR_HWCAPS_READ_8_8_8 |
+ SNOR_HWCAPS_PP_4_4_4 |
+ SNOR_HWCAPS_PP_8_8_8);
+ if (shared_mask & ignored_mask) {
+ dev_dbg(nor->dev,
+ "SPI n-n-n protocols are not supported yet.\n");
+ shared_mask &= ~ignored_mask;
+ }
+
+ /* Select the (Fast) Read command. */
+ err = spi_nor_select_read(nor, params, shared_mask);
+ if (err) {
+ dev_dbg(nor->dev,
+ "can't select read settings supported by both the SPI controller and memory.\n");
+ return err;
+ }
+
+ /* Select the Page Program command. */
+ err = spi_nor_select_pp(nor, params, shared_mask);
+ if (err) {
+ dev_dbg(nor->dev,
+ "can't select write settings supported by both the SPI controller and memory.\n");
+ return err;
+ }
+
+ /* Select the Sector Erase command. */
+ err = spi_nor_select_erase(nor, info);
+ if (err) {
+ dev_dbg(nor->dev,
+ "can't select erase settings supported by both the SPI controller and memory.\n");
+ return err;
+ }
+
+ /* Enable Quad I/O if needed. */
+ enable_quad_io = (spi_nor_get_protocol_width(nor->read_proto) == 4 ||
+ spi_nor_get_protocol_width(nor->write_proto) == 4);
+ if (enable_quad_io && params->quad_enable)
+ nor->quad_enable = params->quad_enable;
+ else
+ nor->quad_enable = NULL;
+
+ return 0;
+}
+
+static int spi_nor_init(struct spi_nor *nor)
+{
+ int err;
+
+ /*
+ * Atmel, SST, Intel/Numonyx, and others serial NOR tend to power up
+ * with the software protection bits set
+ */
+ if (JEDEC_MFR(nor->info) == SNOR_MFR_ATMEL ||
+ JEDEC_MFR(nor->info) == SNOR_MFR_INTEL ||
+ JEDEC_MFR(nor->info) == SNOR_MFR_SST ||
+ nor->info->flags & SPI_NOR_HAS_LOCK) {
+ write_enable(nor);
+ write_sr(nor, 0);
+ spi_nor_wait_till_ready(nor);
+ }
+
+ if (nor->quad_enable) {
+ err = nor->quad_enable(nor);
+ if (err) {
+ dev_dbg(nor->dev, "quad mode not supported\n");
+ return err;
+ }
+ }
+
+ if (nor->addr_width == 4 &&
+ (JEDEC_MFR(nor->info) != SNOR_MFR_SPANSION) &&
+ !(nor->info->flags & SPI_NOR_4B_OPCODES)) {
+ /*
+ * If the RESET# pin isn't hooked up properly, or the system
+ * otherwise doesn't perform a reset command in the boot
+ * sequence, it's impossible to 100% protect against unexpected
+ * reboots (e.g., crashes). Warn the user (or hopefully, system
+ * designer) that this is bad.
+ */
+ if (nor->flags & SNOR_F_BROKEN_RESET)
+ printf("enabling reset hack; may not recover from unexpected reboots\n");
+ set_4byte(nor, nor->info, 1);
+ }
+
+ return 0;
+}
+
+int spi_nor_scan(struct spi_nor *nor)
+{
+ struct spi_nor_flash_parameter params;
+ const struct flash_info *info = NULL;
+ struct mtd_info *mtd = &nor->mtd;
+ struct spi_nor_hwcaps hwcaps = {
+ .mask = SNOR_HWCAPS_READ |
+ SNOR_HWCAPS_READ_FAST |
+ SNOR_HWCAPS_PP,
+ };
+ struct spi_slave *spi = nor->spi;
+ int ret;
+
+ /* Reset SPI protocol for all commands. */
+ nor->reg_proto = SNOR_PROTO_1_1_1;
+ nor->read_proto = SNOR_PROTO_1_1_1;
+ nor->write_proto = SNOR_PROTO_1_1_1;
+ nor->read = spi_nor_read_data;
+ nor->write = spi_nor_write_data;
+ nor->read_reg = spi_nor_read_reg;
+ nor->write_reg = spi_nor_write_reg;
+
+ if (spi->mode & SPI_RX_QUAD) {
+ hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4;
+
+ if (spi->mode & SPI_TX_QUAD)
+ hwcaps.mask |= (SNOR_HWCAPS_READ_1_4_4 |
+ SNOR_HWCAPS_PP_1_1_4 |
+ SNOR_HWCAPS_PP_1_4_4);
+ } else if (spi->mode & SPI_RX_DUAL) {
+ hwcaps.mask |= SNOR_HWCAPS_READ_1_1_2;
+
+ if (spi->mode & SPI_TX_DUAL)
+ hwcaps.mask |= SNOR_HWCAPS_READ_1_2_2;
+ }
+
+ info = spi_nor_read_id(nor);
+ if (IS_ERR_OR_NULL(info))
+ return -ENOENT;
+ /* Parse the Serial Flash Discoverable Parameters table. */
+ ret = spi_nor_init_params(nor, info, ¶ms);
+ if (ret)
+ return ret;
+
+ if (!mtd->name)
+ mtd->name = info->name;
+ mtd->priv = nor;
+ mtd->type = MTD_NORFLASH;
+ mtd->writesize = 1;
+ mtd->flags = MTD_CAP_NORFLASH;
+ mtd->size = params.size;
+ mtd->_erase = spi_nor_erase;
+ mtd->_read = spi_nor_read;
+
+#if defined(CONFIG_SPI_FLASH_STMICRO) || defined(CONFIG_SPI_FLASH_SST)
+ /* NOR protection support for STmicro/Micron chips and similar */
+ if (JEDEC_MFR(info) == SNOR_MFR_ST ||
+ JEDEC_MFR(info) == SNOR_MFR_MICRON ||
+ JEDEC_MFR(info) == SNOR_MFR_SST ||
+ info->flags & SPI_NOR_HAS_LOCK) {
+ nor->flash_lock = stm_lock;
+ nor->flash_unlock = stm_unlock;
+ nor->flash_is_locked = stm_is_locked;
+ }
+#endif
+
+#ifdef CONFIG_SPI_FLASH_SST
+ /* sst nor chips use AAI word program */
+ if (info->flags & SST_WRITE)
+ mtd->_write = sst_write;
+ else
+#endif
+ mtd->_write = spi_nor_write;
+
+ if (info->flags & USE_FSR)
+ nor->flags |= SNOR_F_USE_FSR;
+ if (info->flags & SPI_NOR_HAS_TB)
+ nor->flags |= SNOR_F_HAS_SR_TB;
+ if (info->flags & NO_CHIP_ERASE)
+ nor->flags |= SNOR_F_NO_OP_CHIP_ERASE;
+ if (info->flags & USE_CLSR)
+ nor->flags |= SNOR_F_USE_CLSR;
+
+ if (info->flags & SPI_NOR_NO_ERASE)
+ mtd->flags |= MTD_NO_ERASE;
+
+ nor->page_size = params.page_size;
+ mtd->writebufsize = nor->page_size;
+
+ /* Some devices cannot do fast-read, no matter what DT tells us */
+ if ((info->flags & SPI_NOR_NO_FR) || (spi->mode & SPI_RX_SLOW))
+ params.hwcaps.mask &= ~SNOR_HWCAPS_READ_FAST;
+
+ /*
+ * Configure the SPI memory:
+ * - select op codes for (Fast) Read, Page Program and Sector Erase.
+ * - set the number of dummy cycles (mode cycles + wait states).
+ * - set the SPI protocols for register and memory accesses.
+ * - set the Quad Enable bit if needed (required by SPI x-y-4 protos).
+ */
+ ret = spi_nor_setup(nor, info, ¶ms, &hwcaps);
+ if (ret)
+ return ret;
+
+ if (nor->addr_width) {
+ /* already configured from SFDP */
+ } else if (info->addr_width) {
+ nor->addr_width = info->addr_width;
+ } else if (mtd->size > 0x1000000) {
+ /* enable 4-byte addressing if the device exceeds 16MiB */
+ nor->addr_width = 4;
+ if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
+ info->flags & SPI_NOR_4B_OPCODES)
+ spi_nor_set_4byte_opcodes(nor, info);
+ } else {
+ nor->addr_width = 3;
+ }
+
+ if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) {
+ dev_dbg(dev, "address width is too large: %u\n",
+ nor->addr_width);
+ return -EINVAL;
+ }
+
+ /* Send all the required SPI flash commands to initialize device */
+ nor->info = info;
+ ret = spi_nor_init(nor);
+ if (ret)
+ return ret;
+
+ nor->name = mtd->name;
+ nor->size = mtd->size;
+ nor->erase_size = mtd->erasesize;
+ nor->sector_size = mtd->erasesize;
+
+#ifndef CONFIG_SPL_BUILD
+ printf("SF: Detected %s with page size ", nor->name);
+ print_size(nor->page_size, ", erase size ");
+ print_size(nor->erase_size, ", total ");
+ print_size(nor->size, "");
+ puts("\n");
+#endif
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(spi_nor_scan);
+
+/* U-Boot specific functions, need to extend MTD to support these */
+int spi_flash_cmd_get_sw_write_prot(struct spi_nor *nor)
+{
+ int sr = read_sr(nor);
+
+ if (sr < 0)
+ return sr;
+
+ return (sr >> 2) & 7;
+}
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Huang Shijie <shijie8@gmail.com>");
+MODULE_AUTHOR("Mike Lavender");
+MODULE_DESCRIPTION("framework for SPI NOR");
diff --git a/include/linux/mtd/cfi.h b/include/linux/mtd/cfi.h
new file mode 100644
index 000000000000..3555518bd3f1
--- /dev/null
+++ b/include/linux/mtd/cfi.h
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright © 2000-2010 David Woodhouse <dwmw2@infradead.org> et al.
+ *
+ */
+
+#ifndef __MTD_CFI_H__
+#define __MTD_CFI_H__
+
+#define CFI_MFR_ANY 0xFFFF
+#define CFI_ID_ANY 0xFFFF
+#define CFI_MFR_CONTINUATION 0x007F
+
+#define CFI_MFR_AMD 0x0001
+#define CFI_MFR_AMIC 0x0037
+#define CFI_MFR_ATMEL 0x001F
+#define CFI_MFR_EON 0x001C
+#define CFI_MFR_FUJITSU 0x0004
+#define CFI_MFR_HYUNDAI 0x00AD
+#define CFI_MFR_INTEL 0x0089
+#define CFI_MFR_MACRONIX 0x00C2
+#define CFI_MFR_NEC 0x0010
+#define CFI_MFR_PMC 0x009D
+#define CFI_MFR_SAMSUNG 0x00EC
+#define CFI_MFR_SHARP 0x00B0
+#define CFI_MFR_SST 0x00BF
+#define CFI_MFR_ST 0x0020 /* STMicroelectronics */
+#define CFI_MFR_MICRON 0x002C /* Micron */
+#define CFI_MFR_TOSHIBA 0x0098
+#define CFI_MFR_WINBOND 0x00DA
+
+#endif /* __MTD_CFI_H__ */
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
new file mode 100644
index 000000000000..507458a76076
--- /dev/null
+++ b/include/linux/mtd/spi-nor.h
@@ -0,0 +1,410 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2014 Freescale Semiconductor, Inc.
+ * Synced from Linux v4.19
+ */
+
+#ifndef __LINUX_MTD_SPI_NOR_H
+#define __LINUX_MTD_SPI_NOR_H
+
+#include <linux/bitops.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/mtd.h>
+
+/*
+ * Manufacturer IDs
+ *
+ * The first byte returned from the flash after sending opcode SPINOR_OP_RDID.
+ * Sometimes these are the same as CFI IDs, but sometimes they aren't.
+ */
+#define SNOR_MFR_ATMEL CFI_MFR_ATMEL
+#define SNOR_MFR_GIGADEVICE 0xc8
+#define SNOR_MFR_INTEL CFI_MFR_INTEL
+#define SNOR_MFR_ST CFI_MFR_ST /* ST Micro <--> Micron */
+#define SNOR_MFR_MICRON CFI_MFR_MICRON /* ST Micro <--> Micron */
+#define SNOR_MFR_MACRONIX CFI_MFR_MACRONIX
+#define SNOR_MFR_SPANSION CFI_MFR_AMD
+#define SNOR_MFR_SST CFI_MFR_SST
+#define SNOR_MFR_WINBOND 0xef /* Also used by some Spansion */
+
+/*
+ * Note on opcode nomenclature: some opcodes have a format like
+ * SPINOR_OP_FUNCTION{4,}_x_y_z. The numbers x, y, and z stand for the number
+ * of I/O lines used for the opcode, address, and data (respectively). The
+ * FUNCTION has an optional suffix of '4', to represent an opcode which
+ * requires a 4-byte (32-bit) address.
+ */
+
+/* Flash opcodes. */
+#define SPINOR_OP_WREN 0x06 /* Write enable */
+#define SPINOR_OP_RDSR 0x05 /* Read status register */
+#define SPINOR_OP_WRSR 0x01 /* Write status register 1 byte */
+#define SPINOR_OP_RDSR2 0x3f /* Read status register 2 */
+#define SPINOR_OP_WRSR2 0x3e /* Write status register 2 */
+#define SPINOR_OP_READ 0x03 /* Read data bytes (low frequency) */
+#define SPINOR_OP_READ_FAST 0x0b /* Read data bytes (high frequency) */
+#define SPINOR_OP_READ_1_1_2 0x3b /* Read data bytes (Dual Output SPI) */
+#define SPINOR_OP_READ_1_2_2 0xbb /* Read data bytes (Dual I/O SPI) */
+#define SPINOR_OP_READ_1_1_4 0x6b /* Read data bytes (Quad Output SPI) */
+#define SPINOR_OP_READ_1_4_4 0xeb /* Read data bytes (Quad I/O SPI) */
+#define SPINOR_OP_PP 0x02 /* Page program (up to 256 bytes) */
+#define SPINOR_OP_PP_1_1_4 0x32 /* Quad page program */
+#define SPINOR_OP_PP_1_4_4 0x38 /* Quad page program */
+#define SPINOR_OP_BE_4K 0x20 /* Erase 4KiB block */
+#define SPINOR_OP_BE_4K_PMC 0xd7 /* Erase 4KiB block on PMC chips */
+#define SPINOR_OP_BE_32K 0x52 /* Erase 32KiB block */
+#define SPINOR_OP_CHIP_ERASE 0xc7 /* Erase whole flash chip */
+#define SPINOR_OP_SE 0xd8 /* Sector erase (usually 64KiB) */
+#define SPINOR_OP_RDID 0x9f /* Read JEDEC ID */
+#define SPINOR_OP_RDSFDP 0x5a /* Read SFDP */
+#define SPINOR_OP_RDCR 0x35 /* Read configuration register */
+#define SPINOR_OP_RDFSR 0x70 /* Read flag status register */
+#define SPINOR_OP_CLFSR 0x50 /* Clear flag status register */
+#define SPINOR_OP_RDEAR 0xc8 /* Read Extended Address Register */
+#define SPINOR_OP_WREAR 0xc5 /* Write Extended Address Register */
+
+/* 4-byte address opcodes - used on Spansion and some Macronix flashes. */
+#define SPINOR_OP_READ_4B 0x13 /* Read data bytes (low frequency) */
+#define SPINOR_OP_READ_FAST_4B 0x0c /* Read data bytes (high frequency) */
+#define SPINOR_OP_READ_1_1_2_4B 0x3c /* Read data bytes (Dual Output SPI) */
+#define SPINOR_OP_READ_1_2_2_4B 0xbc /* Read data bytes (Dual I/O SPI) */
+#define SPINOR_OP_READ_1_1_4_4B 0x6c /* Read data bytes (Quad Output SPI) */
+#define SPINOR_OP_READ_1_4_4_4B 0xec /* Read data bytes (Quad I/O SPI) */
+#define SPINOR_OP_PP_4B 0x12 /* Page program (up to 256 bytes) */
+#define SPINOR_OP_PP_1_1_4_4B 0x34 /* Quad page program */
+#define SPINOR_OP_PP_1_4_4_4B 0x3e /* Quad page program */
+#define SPINOR_OP_BE_4K_4B 0x21 /* Erase 4KiB block */
+#define SPINOR_OP_BE_32K_4B 0x5c /* Erase 32KiB block */
+#define SPINOR_OP_SE_4B 0xdc /* Sector erase (usually 64KiB) */
+
+/* Double Transfer Rate opcodes - defined in JEDEC JESD216B. */
+#define SPINOR_OP_READ_1_1_1_DTR 0x0d
+#define SPINOR_OP_READ_1_2_2_DTR 0xbd
+#define SPINOR_OP_READ_1_4_4_DTR 0xed
+
+#define SPINOR_OP_READ_1_1_1_DTR_4B 0x0e
+#define SPINOR_OP_READ_1_2_2_DTR_4B 0xbe
+#define SPINOR_OP_READ_1_4_4_DTR_4B 0xee
+
+/* Used for SST flashes only. */
+#define SPINOR_OP_BP 0x02 /* Byte program */
+#define SPINOR_OP_WRDI 0x04 /* Write disable */
+#define SPINOR_OP_AAI_WP 0xad /* Auto address increment word program */
+
+/* Used for S3AN flashes only */
+#define SPINOR_OP_XSE 0x50 /* Sector erase */
+#define SPINOR_OP_XPP 0x82 /* Page program */
+#define SPINOR_OP_XRDSR 0xd7 /* Read status register */
+
+#define XSR_PAGESIZE BIT(0) /* Page size in Po2 or Linear */
+#define XSR_RDY BIT(7) /* Ready */
+
+/* Used for Macronix and Winbond flashes. */
+#define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */
+#define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */
+
+/* Used for Spansion flashes only. */
+#define SPINOR_OP_BRWR 0x17 /* Bank register write */
+#define SPINOR_OP_CLSR 0x30 /* Clear status register 1 */
+
+/* Used for Micron flashes only. */
+#define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */
+#define SPINOR_OP_WD_EVCR 0x61 /* Write EVCR register */
+
+/* Status Register bits. */
+#define SR_WIP BIT(0) /* Write in progress */
+#define SR_WEL BIT(1) /* Write enable latch */
+/* meaning of other SR_* bits may differ between vendors */
+#define SR_BP0 BIT(2) /* Block protect 0 */
+#define SR_BP1 BIT(3) /* Block protect 1 */
+#define SR_BP2 BIT(4) /* Block protect 2 */
+#define SR_TB BIT(5) /* Top/Bottom protect */
+#define SR_SRWD BIT(7) /* SR write protect */
+/* Spansion/Cypress specific status bits */
+#define SR_E_ERR BIT(5)
+#define SR_P_ERR BIT(6)
+
+#define SR_QUAD_EN_MX BIT(6) /* Macronix Quad I/O */
+
+/* Enhanced Volatile Configuration Register bits */
+#define EVCR_QUAD_EN_MICRON BIT(7) /* Micron Quad I/O */
+
+/* Flag Status Register bits */
+#define FSR_READY BIT(7) /* Device status, 0 = Busy, 1 = Ready */
+#define FSR_E_ERR BIT(5) /* Erase operation status */
+#define FSR_P_ERR BIT(4) /* Program operation status */
+#define FSR_PT_ERR BIT(1) /* Protection error bit */
+
+/* Configuration Register bits. */
+#define CR_QUAD_EN_SPAN BIT(1) /* Spansion Quad I/O */
+
+/* Status Register 2 bits. */
+#define SR2_QUAD_EN_BIT7 BIT(7)
+
+/* Supported SPI protocols */
+#define SNOR_PROTO_INST_MASK GENMASK(23, 16)
+#define SNOR_PROTO_INST_SHIFT 16
+#define SNOR_PROTO_INST(_nbits) \
+ ((((unsigned long)(_nbits)) << SNOR_PROTO_INST_SHIFT) & \
+ SNOR_PROTO_INST_MASK)
+
+#define SNOR_PROTO_ADDR_MASK GENMASK(15, 8)
+#define SNOR_PROTO_ADDR_SHIFT 8
+#define SNOR_PROTO_ADDR(_nbits) \
+ ((((unsigned long)(_nbits)) << SNOR_PROTO_ADDR_SHIFT) & \
+ SNOR_PROTO_ADDR_MASK)
+
+#define SNOR_PROTO_DATA_MASK GENMASK(7, 0)
+#define SNOR_PROTO_DATA_SHIFT 0
+#define SNOR_PROTO_DATA(_nbits) \
+ ((((unsigned long)(_nbits)) << SNOR_PROTO_DATA_SHIFT) & \
+ SNOR_PROTO_DATA_MASK)
+
+#define SNOR_PROTO_IS_DTR BIT(24) /* Double Transfer Rate */
+
+#define SNOR_PROTO_STR(_inst_nbits, _addr_nbits, _data_nbits) \
+ (SNOR_PROTO_INST(_inst_nbits) | \
+ SNOR_PROTO_ADDR(_addr_nbits) | \
+ SNOR_PROTO_DATA(_data_nbits))
+#define SNOR_PROTO_DTR(_inst_nbits, _addr_nbits, _data_nbits) \
+ (SNOR_PROTO_IS_DTR | \
+ SNOR_PROTO_STR(_inst_nbits, _addr_nbits, _data_nbits))
+
+enum spi_nor_protocol {
+ SNOR_PROTO_1_1_1 = SNOR_PROTO_STR(1, 1, 1),
+ SNOR_PROTO_1_1_2 = SNOR_PROTO_STR(1, 1, 2),
+ SNOR_PROTO_1_1_4 = SNOR_PROTO_STR(1, 1, 4),
+ SNOR_PROTO_1_1_8 = SNOR_PROTO_STR(1, 1, 8),
+ SNOR_PROTO_1_2_2 = SNOR_PROTO_STR(1, 2, 2),
+ SNOR_PROTO_1_4_4 = SNOR_PROTO_STR(1, 4, 4),
+ SNOR_PROTO_1_8_8 = SNOR_PROTO_STR(1, 8, 8),
+ SNOR_PROTO_2_2_2 = SNOR_PROTO_STR(2, 2, 2),
+ SNOR_PROTO_4_4_4 = SNOR_PROTO_STR(4, 4, 4),
+ SNOR_PROTO_8_8_8 = SNOR_PROTO_STR(8, 8, 8),
+
+ SNOR_PROTO_1_1_1_DTR = SNOR_PROTO_DTR(1, 1, 1),
+ SNOR_PROTO_1_2_2_DTR = SNOR_PROTO_DTR(1, 2, 2),
+ SNOR_PROTO_1_4_4_DTR = SNOR_PROTO_DTR(1, 4, 4),
+ SNOR_PROTO_1_8_8_DTR = SNOR_PROTO_DTR(1, 8, 8),
+};
+
+static inline bool spi_nor_protocol_is_dtr(enum spi_nor_protocol proto)
+{
+ return !!(proto & SNOR_PROTO_IS_DTR);
+}
+
+static inline u8 spi_nor_get_protocol_inst_nbits(enum spi_nor_protocol proto)
+{
+ return ((unsigned long)(proto & SNOR_PROTO_INST_MASK)) >>
+ SNOR_PROTO_INST_SHIFT;
+}
+
+static inline u8 spi_nor_get_protocol_addr_nbits(enum spi_nor_protocol proto)
+{
+ return ((unsigned long)(proto & SNOR_PROTO_ADDR_MASK)) >>
+ SNOR_PROTO_ADDR_SHIFT;
+}
+
+static inline u8 spi_nor_get_protocol_data_nbits(enum spi_nor_protocol proto)
+{
+ return ((unsigned long)(proto & SNOR_PROTO_DATA_MASK)) >>
+ SNOR_PROTO_DATA_SHIFT;
+}
+
+static inline u8 spi_nor_get_protocol_width(enum spi_nor_protocol proto)
+{
+ return spi_nor_get_protocol_data_nbits(proto);
+}
+
+#define SPI_NOR_MAX_CMD_SIZE 8
+enum spi_nor_ops {
+ SPI_NOR_OPS_READ = 0,
+ SPI_NOR_OPS_WRITE,
+ SPI_NOR_OPS_ERASE,
+ SPI_NOR_OPS_LOCK,
+ SPI_NOR_OPS_UNLOCK,
+};
+
+enum spi_nor_option_flags {
+ SNOR_F_USE_FSR = BIT(0),
+ SNOR_F_HAS_SR_TB = BIT(1),
+ SNOR_F_NO_OP_CHIP_ERASE = BIT(2),
+ SNOR_F_S3AN_ADDR_DEFAULT = BIT(3),
+ SNOR_F_READY_XSR_RDY = BIT(4),
+ SNOR_F_USE_CLSR = BIT(5),
+ SNOR_F_BROKEN_RESET = BIT(6),
+};
+
+/**
+ * struct flash_info - Forward declaration of a structure used internally by
+ * spi_nor_scan()
+ */
+struct flash_info;
+
+/* TODO: Remove, once all users of spi_flash interface are moved to MTD */
+#define spi_flash spi_nor
+
+/**
+ * struct spi_nor - Structure for defining a the SPI NOR layer
+ * @mtd: point to a mtd_info structure
+ * @lock: the lock for the read/write/erase/lock/unlock operations
+ * @dev: point to a spi device, or a spi nor controller device.
+ * @info: spi-nor part JDEC MFR id and other info
+ * @page_size: the page size of the SPI NOR
+ * @addr_width: number of address bytes
+ * @erase_opcode: the opcode for erasing a sector
+ * @read_opcode: the read opcode
+ * @read_dummy: the dummy needed by the read operation
+ * @program_opcode: the program opcode
+ * @sst_write_second: used by the SST write operation
+ * @flags: flag options for the current SPI-NOR (SNOR_F_*)
+ * @read_proto: the SPI protocol for read operations
+ * @write_proto: the SPI protocol for write operations
+ * @reg_proto the SPI protocol for read_reg/write_reg/erase operations
+ * @cmd_buf: used by the write_reg
+ * @prepare: [OPTIONAL] do some preparations for the
+ * read/write/erase/lock/unlock operations
+ * @unprepare: [OPTIONAL] do some post work after the
+ * read/write/erase/lock/unlock operations
+ * @read_reg: [DRIVER-SPECIFIC] read out the register
+ * @write_reg: [DRIVER-SPECIFIC] write data to the register
+ * @read: [DRIVER-SPECIFIC] read data from the SPI NOR
+ * @write: [DRIVER-SPECIFIC] write data to the SPI NOR
+ * @erase: [DRIVER-SPECIFIC] erase a sector of the SPI NOR
+ * at the offset @offs; if not provided by the driver,
+ * spi-nor will send the erase opcode via write_reg()
+ * @flash_lock: [FLASH-SPECIFIC] lock a region of the SPI NOR
+ * @flash_unlock: [FLASH-SPECIFIC] unlock a region of the SPI NOR
+ * @flash_is_locked: [FLASH-SPECIFIC] check if a region of the SPI NOR is
+ * @quad_enable: [FLASH-SPECIFIC] enables SPI NOR quad mode
+ * completely locked
+ * @priv: the private data
+ */
+struct spi_nor {
+ struct mtd_info mtd;
+ struct udevice *dev;
+ struct spi_slave *spi;
+ const struct flash_info *info;
+ u32 page_size;
+ u8 addr_width;
+ u8 erase_opcode;
+ u8 read_opcode;
+ u8 read_dummy;
+ u8 program_opcode;
+ enum spi_nor_protocol read_proto;
+ enum spi_nor_protocol write_proto;
+ enum spi_nor_protocol reg_proto;
+ bool sst_write_second;
+ u32 flags;
+ u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE];
+
+ int (*prepare)(struct spi_nor *nor, enum spi_nor_ops ops);
+ void (*unprepare)(struct spi_nor *nor, enum spi_nor_ops ops);
+ int (*read_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len);
+ int (*write_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len);
+
+ ssize_t (*read)(struct spi_nor *nor, loff_t from,
+ size_t len, u_char *read_buf);
+ ssize_t (*write)(struct spi_nor *nor, loff_t to,
+ size_t len, const u_char *write_buf);
+ int (*erase)(struct spi_nor *nor, loff_t offs);
+
+ int (*flash_lock)(struct spi_nor *nor, loff_t ofs, uint64_t len);
+ int (*flash_unlock)(struct spi_nor *nor, loff_t ofs, uint64_t len);
+ int (*flash_is_locked)(struct spi_nor *nor, loff_t ofs, uint64_t len);
+ int (*quad_enable)(struct spi_nor *nor);
+
+ void *priv;
+/* Compatibility for spi_flash, remove once sf layer is merged with mtd */
+ const char *name;
+ u32 size;
+ u32 sector_size;
+ u32 erase_size;
+};
+
+static inline void spi_nor_set_flash_node(struct spi_nor *nor,
+ const struct device_node *np)
+{
+ mtd_set_of_node(&nor->mtd, np);
+}
+
+static inline const struct
+device_node *spi_nor_get_flash_node(struct spi_nor *nor)
+{
+ return mtd_get_of_node(&nor->mtd);
+}
+
+/**
+ * struct spi_nor_hwcaps - Structure for describing the hardware capabilies
+ * supported by the SPI controller (bus master).
+ * @mask: the bitmask listing all the supported hw capabilies
+ */
+struct spi_nor_hwcaps {
+ u32 mask;
+};
+
+/*
+ *(Fast) Read capabilities.
+ * MUST be ordered by priority: the higher bit position, the higher priority.
+ * As a matter of performances, it is relevant to use Octo SPI protocols first,
+ * then Quad SPI protocols before Dual SPI protocols, Fast Read and lastly
+ * (Slow) Read.
+ */
+#define SNOR_HWCAPS_READ_MASK GENMASK(14, 0)
+#define SNOR_HWCAPS_READ BIT(0)
+#define SNOR_HWCAPS_READ_FAST BIT(1)
+#define SNOR_HWCAPS_READ_1_1_1_DTR BIT(2)
+
+#define SNOR_HWCAPS_READ_DUAL GENMASK(6, 3)
+#define SNOR_HWCAPS_READ_1_1_2 BIT(3)
+#define SNOR_HWCAPS_READ_1_2_2 BIT(4)
+#define SNOR_HWCAPS_READ_2_2_2 BIT(5)
+#define SNOR_HWCAPS_READ_1_2_2_DTR BIT(6)
+
+#define SNOR_HWCAPS_READ_QUAD GENMASK(10, 7)
+#define SNOR_HWCAPS_READ_1_1_4 BIT(7)
+#define SNOR_HWCAPS_READ_1_4_4 BIT(8)
+#define SNOR_HWCAPS_READ_4_4_4 BIT(9)
+#define SNOR_HWCAPS_READ_1_4_4_DTR BIT(10)
+
+#define SNOR_HWCPAS_READ_OCTO GENMASK(14, 11)
+#define SNOR_HWCAPS_READ_1_1_8 BIT(11)
+#define SNOR_HWCAPS_READ_1_8_8 BIT(12)
+#define SNOR_HWCAPS_READ_8_8_8 BIT(13)
+#define SNOR_HWCAPS_READ_1_8_8_DTR BIT(14)
+
+/*
+ * Page Program capabilities.
+ * MUST be ordered by priority: the higher bit position, the higher priority.
+ * Like (Fast) Read capabilities, Octo/Quad SPI protocols are preferred to the
+ * legacy SPI 1-1-1 protocol.
+ * Note that Dual Page Programs are not supported because there is no existing
+ * JEDEC/SFDP standard to define them. Also at this moment no SPI flash memory
+ * implements such commands.
+ */
+#define SNOR_HWCAPS_PP_MASK GENMASK(22, 16)
+#define SNOR_HWCAPS_PP BIT(16)
+
+#define SNOR_HWCAPS_PP_QUAD GENMASK(19, 17)
+#define SNOR_HWCAPS_PP_1_1_4 BIT(17)
+#define SNOR_HWCAPS_PP_1_4_4 BIT(18)
+#define SNOR_HWCAPS_PP_4_4_4 BIT(19)
+
+#define SNOR_HWCAPS_PP_OCTO GENMASK(22, 20)
+#define SNOR_HWCAPS_PP_1_1_8 BIT(20)
+#define SNOR_HWCAPS_PP_1_8_8 BIT(21)
+#define SNOR_HWCAPS_PP_8_8_8 BIT(22)
+
+/**
+ * spi_nor_scan() - scan the SPI NOR
+ * @nor: the spi_nor structure
+ *
+ * The drivers can use this function to scan the SPI NOR.
+ * In the scanning, it will try to get all the necessary information to
+ * fill the mtd_info{} and the spi_nor{}.
+ *
+ * Return: 0 for success, others for failure.
+ */
+int spi_nor_scan(struct spi_nor *nor);
+
+#endif
--
2.20.1
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 05/11] mtd: spi: Switch to new SPI NOR framework
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (3 preceding siblings ...)
2018-12-21 6:38 ` [U-Boot] [PATCH v2 04/11] mtd: spi: Port SPI NOR framework from Linux Vignesh R
@ 2018-12-21 6:38 ` Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 06/11] mtd: spi: Remove unused files Vignesh R
` (9 subsequent siblings)
14 siblings, 0 replies; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
use new interfaces/defintions
Keep U-Boot feature SPI_FLASH_BAR as is.
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
common/spl/Kconfig | 13 +-
drivers/mtd/spi/Kconfig | 16 ++-
drivers/mtd/spi/Makefile | 4 +-
drivers/mtd/spi/sandbox.c | 36 +++---
drivers/mtd/spi/sf_dataflash.c | 11 +-
drivers/mtd/spi/sf_internal.h | 225 ++++++---------------------------
drivers/mtd/spi/sf_probe.c | 33 +++--
drivers/mtd/spi/spi-nor-core.c | 220 +++++++++++++++++++++++---------
drivers/spi/stm32_qspi.c | 4 +-
include/linux/mtd/spi-nor.h | 9 ++
include/spi_flash.h | 105 ++++-----------
11 files changed, 303 insertions(+), 373 deletions(-)
diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index 953841ebe761..9d8405b7daa8 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -729,13 +729,24 @@ config SPL_SPI_FLASH_SUPPORT
lines). This enables the drivers in drivers/mtd/spi as part of an
SPL build. This normally requires SPL_SPI_SUPPORT.
+if SPL_SPI_FLASH_SUPPORT
+
+config SPL_SPI_FLASH_SFDP_SUPPORT
+ bool "SFDP table parsing support for SPI NOR flashes"
+ depends on !SPI_FLASH_BAR
+ help
+ Enable support for parsing and auto discovery of parameters for
+ SPI NOR flashes using Serial Flash Discoverable Parameters (SFDP)
+ tables as per JESD216 standard in SPL.
+
config SPL_SPI_LOAD
bool "Support loading from SPI flash"
- depends on SPL_SPI_FLASH_SUPPORT
help
Enable support for loading next stage, U-Boot or otherwise, from
SPI NOR in U-Boot SPL.
+endif # SPL_SPI_FLASH_SUPPORT
+
config SPL_SPI_SUPPORT
bool "Support SPI drivers"
help
diff --git a/drivers/mtd/spi/Kconfig b/drivers/mtd/spi/Kconfig
index 76d5a1d11527..e3b40fc157d6 100644
--- a/drivers/mtd/spi/Kconfig
+++ b/drivers/mtd/spi/Kconfig
@@ -27,6 +27,8 @@ config SPI_FLASH_SANDBOX
config SPI_FLASH
bool "Legacy SPI Flash Interface support"
+ depends on SPI
+ select SPI_MEM
help
Enable the legacy SPI flash support. This will include basic
standard support for things like probing, read / write, and
@@ -34,9 +36,18 @@ config SPI_FLASH
If unsure, say N
+if SPI_FLASH
+
+config SPI_FLASH_SFDP_SUPPORT
+ bool "SFDP table parsing support for SPI NOR flashes"
+ depends on !SPI_FLASH_BAR
+ help
+ Enable support for parsing and auto discovery of parameters for
+ SPI NOR flashes using Serial Flash Discoverable Parameters (SFDP)
+ tables as per JESD216 standard.
+
config SPI_FLASH_BAR
bool "SPI flash Bank/Extended address register support"
- depends on SPI_FLASH
help
Enable the SPI flash Bank/Extended address register support.
Bank/Extended address registers are used to access the flash
@@ -44,13 +55,10 @@ config SPI_FLASH_BAR
config SF_DUAL_FLASH
bool "SPI DUAL flash memory support"
- depends on SPI_FLASH
help
Enable this option to support two flash memories connected to a single
controller. Currently Xilinx Zynq qspi supports this.
-if SPI_FLASH
-
config SPI_FLASH_ATMEL
bool "Atmel SPI flash support"
help
diff --git a/drivers/mtd/spi/Makefile b/drivers/mtd/spi/Makefile
index b4c7e1c98bd5..70058d3df2b9 100644
--- a/drivers/mtd/spi/Makefile
+++ b/drivers/mtd/spi/Makefile
@@ -9,7 +9,7 @@ ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_SPI_BOOT) += fsl_espi_spl.o
endif
-obj-$(CONFIG_SPI_FLASH) += sf_probe.o spi_flash.o spi_flash_ids.o sf.o
-obj-$(CONFIG_SPI_FLASH_DATAFLASH) += sf_dataflash.o
+obj-$(CONFIG_SPI_FLASH) += sf_probe.o spi-nor-core.o
+obj-$(CONFIG_SPI_FLASH_DATAFLASH) += sf_dataflash.o sf.o
obj-$(CONFIG_SPI_FLASH_MTD) += sf_mtd.o
obj-$(CONFIG_SPI_FLASH_SANDBOX) += sandbox.o
diff --git a/drivers/mtd/spi/sandbox.c b/drivers/mtd/spi/sandbox.c
index 7b9891cb981c..084c66e9840b 100644
--- a/drivers/mtd/spi/sandbox.c
+++ b/drivers/mtd/spi/sandbox.c
@@ -92,7 +92,7 @@ struct sandbox_spi_flash {
/* The current flash status (see STAT_XXX defines above) */
u16 status;
/* Data describing the flash we're emulating */
- const struct spi_flash_info *data;
+ const struct flash_info *data;
/* The file on disk to serv up data from */
int fd;
};
@@ -122,7 +122,7 @@ static int sandbox_sf_probe(struct udevice *dev)
/* spec = idcode:file */
struct sandbox_spi_flash *sbsf = dev_get_priv(dev);
size_t len, idname_len;
- const struct spi_flash_info *data;
+ const struct flash_info *data;
struct sandbox_spi_flash_plat_data *pdata = dev_get_platdata(dev);
struct sandbox_state *state = state_get_current();
struct dm_spi_slave_platdata *slave_plat;
@@ -155,7 +155,7 @@ static int sandbox_sf_probe(struct udevice *dev)
idname_len = strlen(spec);
debug("%s: device='%s'\n", __func__, spec);
- for (data = spi_flash_ids; data->name; data++) {
+ for (data = spi_nor_ids; data->name; data++) {
len = strlen(data->name);
if (idname_len != len)
continue;
@@ -243,43 +243,43 @@ static int sandbox_sf_process_cmd(struct sandbox_spi_flash *sbsf, const u8 *rx,
sbsf->cmd = rx[0];
switch (sbsf->cmd) {
- case CMD_READ_ID:
+ case SPINOR_OP_RDID:
sbsf->state = SF_ID;
sbsf->cmd = SF_ID;
break;
- case CMD_READ_ARRAY_FAST:
+ case SPINOR_OP_READ_FAST:
sbsf->pad_addr_bytes = 1;
- case CMD_READ_ARRAY_SLOW:
- case CMD_PAGE_PROGRAM:
+ case SPINOR_OP_READ:
+ case SPINOR_OP_PP:
sbsf->state = SF_ADDR;
break;
- case CMD_WRITE_DISABLE:
+ case SPINOR_OP_WRDI:
debug(" write disabled\n");
sbsf->status &= ~STAT_WEL;
break;
- case CMD_READ_STATUS:
+ case SPINOR_OP_RDSR:
sbsf->state = SF_READ_STATUS;
break;
- case CMD_READ_STATUS1:
+ case SPINOR_OP_RDSR2:
sbsf->state = SF_READ_STATUS1;
break;
- case CMD_WRITE_ENABLE:
+ case SPINOR_OP_WREN:
debug(" write enabled\n");
sbsf->status |= STAT_WEL;
break;
- case CMD_WRITE_STATUS:
+ case SPINOR_OP_WRSR:
sbsf->state = SF_WRITE_STATUS;
break;
default: {
int flags = sbsf->data->flags;
/* we only support erase here */
- if (sbsf->cmd == CMD_ERASE_CHIP) {
+ if (sbsf->cmd == SPINOR_OP_CHIP_ERASE) {
sbsf->erase_size = sbsf->data->sector_size *
sbsf->data->n_sectors;
- } else if (sbsf->cmd == CMD_ERASE_4K && (flags & SECT_4K)) {
+ } else if (sbsf->cmd == SPINOR_OP_BE_4K && (flags & SECT_4K)) {
sbsf->erase_size = 4 << 10;
- } else if (sbsf->cmd == CMD_ERASE_64K && !(flags & SECT_4K)) {
+ } else if (sbsf->cmd == SPINOR_OP_SE && !(flags & SECT_4K)) {
sbsf->erase_size = 64 << 10;
} else {
debug(" cmd unknown: %#x\n", sbsf->cmd);
@@ -380,11 +380,11 @@ static int sandbox_sf_xfer(struct udevice *dev, unsigned int bitlen,
return -EIO;
}
switch (sbsf->cmd) {
- case CMD_READ_ARRAY_FAST:
- case CMD_READ_ARRAY_SLOW:
+ case SPINOR_OP_READ_FAST:
+ case SPINOR_OP_READ:
sbsf->state = SF_READ;
break;
- case CMD_PAGE_PROGRAM:
+ case SPINOR_OP_PP:
sbsf->state = SF_WRITE;
break;
default:
diff --git a/drivers/mtd/spi/sf_dataflash.c b/drivers/mtd/spi/sf_dataflash.c
index 4a60c1b2b43a..b6a2631747a9 100644
--- a/drivers/mtd/spi/sf_dataflash.c
+++ b/drivers/mtd/spi/sf_dataflash.c
@@ -18,6 +18,7 @@
#include "sf_internal.h"
+#define CMD_READ_ID 0x9f
/* reads can bypass the buffers */
#define OP_READ_CONTINUOUS 0xE8
#define OP_READ_PAGE 0xD2
@@ -441,7 +442,7 @@ static int add_dataflash(struct udevice *dev, char *name, int nr_pages,
return 0;
}
-struct flash_info {
+struct data_flash_info {
char *name;
/*
@@ -460,7 +461,7 @@ struct flash_info {
#define IS_POW2PS 0x0001 /* uses 2^N byte pages */
};
-static struct flash_info dataflash_data[] = {
+static struct data_flash_info dataflash_data[] = {
/*
* NOTE: chips with SUP_POW2PS (rev D and up) need two entries,
* one with IS_POW2PS and the other without. The entry with the
@@ -501,12 +502,12 @@ static struct flash_info dataflash_data[] = {
{ "at45db642d", 0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS},
};
-static struct flash_info *jedec_probe(struct spi_slave *spi)
+static struct data_flash_info *jedec_probe(struct spi_slave *spi)
{
int tmp;
uint8_t id[5];
uint32_t jedec;
- struct flash_info *info;
+ struct data_flash_info *info;
int status;
/*
@@ -583,7 +584,7 @@ static int spi_dataflash_probe(struct udevice *dev)
{
struct spi_slave *spi = dev_get_parent_priv(dev);
struct spi_flash *spi_flash;
- struct flash_info *info;
+ struct data_flash_info *info;
int status;
spi_flash = dev_get_uclass_priv(dev);
diff --git a/drivers/mtd/spi/sf_internal.h b/drivers/mtd/spi/sf_internal.h
index 46a504441751..fd00e0d1b23b 100644
--- a/drivers/mtd/spi/sf_internal.h
+++ b/drivers/mtd/spi/sf_internal.h
@@ -12,142 +12,63 @@
#include <linux/types.h>
#include <linux/compiler.h>
-/* Dual SPI flash memories - see SPI_COMM_DUAL_... */
-enum spi_dual_flash {
- SF_SINGLE_FLASH = 0,
- SF_DUAL_STACKED_FLASH = BIT(0),
- SF_DUAL_PARALLEL_FLASH = BIT(1),
-};
-
-enum spi_nor_option_flags {
- SNOR_F_SST_WR = BIT(0),
- SNOR_F_USE_FSR = BIT(1),
- SNOR_F_USE_UPAGE = BIT(3),
-};
-
-#define SPI_FLASH_3B_ADDR_LEN 3
-#define SPI_FLASH_CMD_LEN (1 + SPI_FLASH_3B_ADDR_LEN)
-#define SPI_FLASH_16MB_BOUN 0x1000000
-
-/* CFI Manufacture ID's */
-#define SPI_FLASH_CFI_MFR_SPANSION 0x01
-#define SPI_FLASH_CFI_MFR_STMICRO 0x20
-#define SPI_FLASH_CFI_MFR_MICRON 0x2C
-#define SPI_FLASH_CFI_MFR_MACRONIX 0xc2
-#define SPI_FLASH_CFI_MFR_SST 0xbf
-#define SPI_FLASH_CFI_MFR_WINBOND 0xef
-#define SPI_FLASH_CFI_MFR_ATMEL 0x1f
-
-/* Erase commands */
-#define CMD_ERASE_4K 0x20
-#define CMD_ERASE_CHIP 0xc7
-#define CMD_ERASE_64K 0xd8
-
-/* Write commands */
-#define CMD_WRITE_STATUS 0x01
-#define CMD_PAGE_PROGRAM 0x02
-#define CMD_WRITE_DISABLE 0x04
-#define CMD_WRITE_ENABLE 0x06
-#define CMD_QUAD_PAGE_PROGRAM 0x32
-
-/* Read commands */
-#define CMD_READ_ARRAY_SLOW 0x03
-#define CMD_READ_ARRAY_FAST 0x0b
-#define CMD_READ_DUAL_OUTPUT_FAST 0x3b
-#define CMD_READ_DUAL_IO_FAST 0xbb
-#define CMD_READ_QUAD_OUTPUT_FAST 0x6b
-#define CMD_READ_QUAD_IO_FAST 0xeb
-#define CMD_READ_ID 0x9f
-#define CMD_READ_STATUS 0x05
-#define CMD_READ_STATUS1 0x35
-#define CMD_READ_CONFIG 0x35
-#define CMD_FLAG_STATUS 0x70
-
-/* Bank addr access commands */
-#ifdef CONFIG_SPI_FLASH_BAR
-# define CMD_BANKADDR_BRWR 0x17
-# define CMD_BANKADDR_BRRD 0x16
-# define CMD_EXTNADDR_WREAR 0xC5
-# define CMD_EXTNADDR_RDEAR 0xC8
-#endif
-
-/* Common status */
-#define STATUS_WIP BIT(0)
-#define STATUS_QEB_WINSPAN BIT(1)
-#define STATUS_QEB_MXIC BIT(6)
-#define STATUS_PEC BIT(7)
-#define SR_BP0 BIT(2) /* Block protect 0 */
-#define SR_BP1 BIT(3) /* Block protect 1 */
-#define SR_BP2 BIT(4) /* Block protect 2 */
-
-/* Flash timeout values */
-#define SPI_FLASH_PROG_TIMEOUT (2 * CONFIG_SYS_HZ)
-#define SPI_FLASH_PAGE_ERASE_TIMEOUT (5 * CONFIG_SYS_HZ)
-#define SPI_FLASH_SECTOR_ERASE_TIMEOUT (10 * CONFIG_SYS_HZ)
-
-/* SST specific */
-#ifdef CONFIG_SPI_FLASH_SST
-#define SST26_CMD_READ_BPR 0x72
-#define SST26_CMD_WRITE_BPR 0x42
-
-#define SST26_BPR_8K_NUM 4
-#define SST26_MAX_BPR_REG_LEN (18 + 1)
-#define SST26_BOUND_REG_SIZE ((32 + SST26_BPR_8K_NUM * 8) * SZ_1K)
-
-enum lock_ctl {
- SST26_CTL_LOCK,
- SST26_CTL_UNLOCK,
- SST26_CTL_CHECK
-};
-
-# define CMD_SST_BP 0x02 /* Byte Program */
-# define CMD_SST_AAI_WP 0xAD /* Auto Address Incr Word Program */
-
-int sst_write_wp(struct spi_flash *flash, u32 offset, size_t len,
- const void *buf);
-int sst_write_bp(struct spi_flash *flash, u32 offset, size_t len,
- const void *buf);
-#endif
-
-#define JEDEC_MFR(info) ((info)->id[0])
-#define JEDEC_ID(info) (((info)->id[1]) << 8 | ((info)->id[2]))
-#define JEDEC_EXT(info) (((info)->id[3]) << 8 | ((info)->id[4]))
-#define SPI_FLASH_MAX_ID_LEN 6
+#define SPI_NOR_MAX_ID_LEN 6
+#define SPI_NOR_MAX_ADDR_WIDTH 4
-struct spi_flash_info {
- /* Device name ([MANUFLETTER][DEVTYPE][DENSITY][EXTRAINFO]) */
- const char *name;
+struct flash_info {
+ char *name;
/*
* This array stores the ID bytes.
* The first three bytes are the JEDIC ID.
* JEDEC ID zero means "no ID" (mostly older chips).
*/
- u8 id[SPI_FLASH_MAX_ID_LEN];
+ u8 id[SPI_NOR_MAX_ID_LEN];
u8 id_len;
- /*
- * The size listed here is what works with SPINOR_OP_SE, which isn't
+ /* The size listed here is what works with SPINOR_OP_SE, which isn't
* necessarily called a "sector" by the vendor.
*/
- u32 sector_size;
- u32 n_sectors;
+ unsigned int sector_size;
+ u16 n_sectors;
u16 page_size;
+ u16 addr_width;
u16 flags;
-#define SECT_4K BIT(0) /* CMD_ERASE_4K works uniformly */
-#define E_FSR BIT(1) /* use flag status register for */
-#define SST_WR BIT(2) /* use SST byte/word programming */
-#define WR_QPP BIT(3) /* use Quad Page Program */
-#define RD_QUAD BIT(4) /* use Quad Read */
-#define RD_DUAL BIT(5) /* use Dual Read */
-#define RD_QUADIO BIT(6) /* use Quad IO Read */
-#define RD_DUALIO BIT(7) /* use Dual IO Read */
-#define RD_FULL (RD_QUAD | RD_DUAL | RD_QUADIO | RD_DUALIO)
+#define SECT_4K BIT(0) /* SPINOR_OP_BE_4K works uniformly */
+#define SPI_NOR_NO_ERASE BIT(1) /* No erase command needed */
+#define SST_WRITE BIT(2) /* use SST byte programming */
+#define SPI_NOR_NO_FR BIT(3) /* Can't do fastread */
+#define SECT_4K_PMC BIT(4) /* SPINOR_OP_BE_4K_PMC works uniformly */
+#define SPI_NOR_DUAL_READ BIT(5) /* Flash supports Dual Read */
+#define SPI_NOR_QUAD_READ BIT(6) /* Flash supports Quad Read */
+#define USE_FSR BIT(7) /* use flag status register */
+#define SPI_NOR_HAS_LOCK BIT(8) /* Flash supports lock/unlock via SR */
+#define SPI_NOR_HAS_TB BIT(9) /*
+ * Flash SR has Top/Bottom (TB) protect
+ * bit. Must be used with
+ * SPI_NOR_HAS_LOCK.
+ */
+#define SPI_S3AN BIT(10) /*
+ * Xilinx Spartan 3AN In-System Flash
+ * (MFR cannot be used for probing
+ * because it has the same value as
+ * ATMEL flashes)
+ */
+#define SPI_NOR_4B_OPCODES BIT(11) /*
+ * Use dedicated 4byte address op codes
+ * to support memory size above 128Mib.
+ */
+#define NO_CHIP_ERASE BIT(12) /* Chip does not support chip erase */
+#define SPI_NOR_SKIP_SFDP BIT(13) /* Skip parsing of SFDP tables */
+#define USE_CLSR BIT(14) /* use CLSR command */
};
-extern const struct spi_flash_info spi_flash_ids[];
+extern const struct flash_info spi_nor_ids[];
+
+#define JEDEC_MFR(info) ((info)->id[0])
+#define JEDEC_ID(info) (((info)->id[1]) << 8 | ((info)->id[2]))
/* Send a single-byte command to the device and read the response */
int spi_flash_cmd(struct spi_slave *spi, u8 cmd, void *response, size_t len);
@@ -167,78 +88,12 @@ int spi_flash_cmd_write(struct spi_slave *spi, const u8 *cmd, size_t cmd_len,
const void *data, size_t data_len);
-/* Flash erase(sectors) operation, support all possible erase commands */
-int spi_flash_cmd_erase_ops(struct spi_flash *flash, u32 offset, size_t len);
-
/* Get software write-protect value (BP bits) */
int spi_flash_cmd_get_sw_write_prot(struct spi_flash *flash);
-/* Lock stmicro spi flash region */
-int stm_lock(struct spi_flash *flash, u32 ofs, size_t len);
-
-/* Unlock stmicro spi flash region */
-int stm_unlock(struct spi_flash *flash, u32 ofs, size_t len);
-
-/* Check if a stmicro spi flash region is completely locked */
-int stm_is_locked(struct spi_flash *flash, u32 ofs, size_t len);
-
-/* Enable writing on the SPI flash */
-static inline int spi_flash_cmd_write_enable(struct spi_flash *flash)
-{
- return spi_flash_cmd(flash->spi, CMD_WRITE_ENABLE, NULL, 0);
-}
-
-/* Disable writing on the SPI flash */
-static inline int spi_flash_cmd_write_disable(struct spi_flash *flash)
-{
- return spi_flash_cmd(flash->spi, CMD_WRITE_DISABLE, NULL, 0);
-}
-
-/*
- * Used for spi_flash write operation
- * - SPI claim
- * - spi_flash_cmd_write_enable
- * - spi_flash_cmd_write
- * - spi_flash_wait_till_ready
- * - SPI release
- */
-int spi_flash_write_common(struct spi_flash *flash, const u8 *cmd,
- size_t cmd_len, const void *buf, size_t buf_len);
-
-/*
- * Flash write operation, support all possible write commands.
- * Write the requested data out breaking it up into multiple write
- * commands as needed per the write size.
- */
-int spi_flash_cmd_write_ops(struct spi_flash *flash, u32 offset,
- size_t len, const void *buf);
-
-/*
- * Same as spi_flash_cmd_read() except it also claims/releases the SPI
- * bus. Used as common part of the ->read() operation.
- */
-int spi_flash_read_common(struct spi_flash *flash, const u8 *cmd,
- size_t cmd_len, void *data, size_t data_len);
-
-/* Flash read operation, support all possible read commands */
-int spi_flash_cmd_read_ops(struct spi_flash *flash, u32 offset,
- size_t len, void *data);
#ifdef CONFIG_SPI_FLASH_MTD
int spi_flash_mtd_register(struct spi_flash *flash);
void spi_flash_mtd_unregister(void);
#endif
-
-/**
- * spi_flash_scan - scan the SPI FLASH
- * @flash: the spi flash structure
- *
- * The drivers can use this fuction to scan the SPI FLASH.
- * In the scanning, it will try to get all the necessary information to
- * fill the spi_flash{}.
- *
- * Return: 0 for success, others for failure.
- */
-int spi_flash_scan(struct spi_flash *flash);
-
#endif /* _SF_INTERNAL_H_ */
diff --git a/drivers/mtd/spi/sf_probe.c b/drivers/mtd/spi/sf_probe.c
index 00f8558e7019..7f1378f4946d 100644
--- a/drivers/mtd/spi/sf_probe.c
+++ b/drivers/mtd/spi/sf_probe.c
@@ -40,7 +40,7 @@ static int spi_flash_probe_slave(struct spi_flash *flash)
return ret;
}
- ret = spi_flash_scan(flash);
+ ret = spi_nor_scan(flash);
if (ret)
goto err_read_id;
@@ -96,32 +96,38 @@ static int spi_flash_std_read(struct udevice *dev, u32 offset, size_t len,
void *buf)
{
struct spi_flash *flash = dev_get_uclass_priv(dev);
+ struct mtd_info *mtd = &flash->mtd;
+ size_t retlen;
- return log_ret(spi_flash_cmd_read_ops(flash, offset, len, buf));
+ return log_ret(mtd->_read(mtd, offset, len, &retlen, buf));
}
static int spi_flash_std_write(struct udevice *dev, u32 offset, size_t len,
const void *buf)
{
struct spi_flash *flash = dev_get_uclass_priv(dev);
+ struct mtd_info *mtd = &flash->mtd;
+ size_t retlen;
-#if defined(CONFIG_SPI_FLASH_SST)
- if (flash->flags & SNOR_F_SST_WR) {
- if (flash->spi->mode & SPI_TX_BYTE)
- return sst_write_bp(flash, offset, len, buf);
- else
- return sst_write_wp(flash, offset, len, buf);
- }
-#endif
-
- return spi_flash_cmd_write_ops(flash, offset, len, buf);
+ return mtd->_write(mtd, offset, len, &retlen, buf);
}
static int spi_flash_std_erase(struct udevice *dev, u32 offset, size_t len)
{
struct spi_flash *flash = dev_get_uclass_priv(dev);
+ struct mtd_info *mtd = &flash->mtd;
+ struct erase_info instr;
+
+ if (offset % mtd->erasesize || len % mtd->erasesize) {
+ printf("SF: Erase offset/length not multiple of erase size\n");
+ return -EINVAL;
+ }
+
+ memset(&instr, 0, sizeof(instr));
+ instr.addr = offset;
+ instr.len = len;
- return spi_flash_cmd_erase_ops(flash, offset, len);
+ return mtd->_erase(mtd, &instr);
}
static int spi_flash_std_get_sw_write_prot(struct udevice *dev)
@@ -161,6 +167,7 @@ static const struct dm_spi_flash_ops spi_flash_std_ops = {
static const struct udevice_id spi_flash_std_ids[] = {
{ .compatible = "spi-flash" },
+ { .compatible = "jedec,spi-nor" },
{ }
};
diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c
index 597898d3b4af..c2e5f9320b95 100644
--- a/drivers/mtd/spi/spi-nor-core.c
+++ b/drivers/mtd/spi/spi-nor-core.c
@@ -21,6 +21,8 @@
#include <spi-mem.h>
#include <spi.h>
+#include "sf_internal.h"
+
/* Define max times to check status register before we give up. */
/*
@@ -32,63 +34,6 @@
#define DEFAULT_READY_WAIT_JIFFIES (40UL * HZ)
-#define SPI_NOR_MAX_ID_LEN 6
-#define SPI_NOR_MAX_ADDR_WIDTH 4
-
-struct flash_info {
- char *name;
-
- /*
- * This array stores the ID bytes.
- * The first three bytes are the JEDIC ID.
- * JEDEC ID zero means "no ID" (mostly older chips).
- */
- u8 id[SPI_NOR_MAX_ID_LEN];
- u8 id_len;
-
- /* The size listed here is what works with SPINOR_OP_SE, which isn't
- * necessarily called a "sector" by the vendor.
- */
- unsigned int sector_size;
- u16 n_sectors;
-
- u16 page_size;
- u16 addr_width;
-
- u16 flags;
-#define SECT_4K BIT(0) /* SPINOR_OP_BE_4K works uniformly */
-#define SPI_NOR_NO_ERASE BIT(1) /* No erase command needed */
-#define SST_WRITE BIT(2) /* use SST byte programming */
-#define SPI_NOR_NO_FR BIT(3) /* Can't do fastread */
-#define SECT_4K_PMC BIT(4) /* SPINOR_OP_BE_4K_PMC works uniformly */
-#define SPI_NOR_DUAL_READ BIT(5) /* Flash supports Dual Read */
-#define SPI_NOR_QUAD_READ BIT(6) /* Flash supports Quad Read */
-#define USE_FSR BIT(7) /* use flag status register */
-#define SPI_NOR_HAS_LOCK BIT(8) /* Flash supports lock/unlock via SR */
-#define SPI_NOR_HAS_TB BIT(9) /*
- * Flash SR has Top/Bottom (TB) protect
- * bit. Must be used with
- * SPI_NOR_HAS_LOCK.
- */
-#define SPI_S3AN BIT(10) /*
- * Xilinx Spartan 3AN In-System Flash
- * (MFR cannot be used for probing
- * because it has the same value as
- * ATMEL flashes)
- */
-#define SPI_NOR_4B_OPCODES BIT(11) /*
- * Use dedicated 4byte address op codes
- * to support memory size above 128Mib.
- */
-#define NO_CHIP_ERASE BIT(12) /* Chip does not support chip erase */
-#define SPI_NOR_SKIP_SFDP BIT(13) /* Skip parsing of SFDP tables */
-#define USE_CLSR BIT(14) /* use CLSR command */
-
- int (*quad_enable)(struct spi_nor *nor);
-};
-
-#define JEDEC_MFR(info) ((info)->id[0])
-
static int spi_nor_read_write_reg(struct spi_nor *nor, struct spi_mem_op
*op, void *buf)
{
@@ -291,6 +236,7 @@ static struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd)
return mtd->priv;
}
+#ifndef CONFIG_SPI_FLASH_BAR
static u8 spi_nor_convert_opcode(u8 opcode, const u8 table[][2], size_t size)
{
size_t i;
@@ -365,6 +311,7 @@ static void spi_nor_set_4byte_opcodes(struct spi_nor *nor,
nor->program_opcode = spi_nor_convert_3to4_program(nor->program_opcode);
nor->erase_opcode = spi_nor_convert_3to4_erase(nor->erase_opcode);
}
+#endif /* !CONFIG_SPI_FLASH_BAR */
/* Enable/disable 4-byte addressing mode. */
static int set_4byte(struct spi_nor *nor, const struct flash_info *info,
@@ -501,6 +448,79 @@ static int spi_nor_wait_till_ready(struct spi_nor *nor)
DEFAULT_READY_WAIT_JIFFIES);
}
+#ifdef CONFIG_SPI_FLASH_BAR
+/*
+ * This "clean_bar" is necessary in a situation when one was accessing
+ * spi flash memory > 16 MiB by using Bank Address Register's BA24 bit.
+ *
+ * After it the BA24 bit shall be cleared to allow access to correct
+ * memory region after SW reset (by calling "reset" command).
+ *
+ * Otherwise, the BA24 bit may be left set and then after reset, the
+ * ROM would read/write/erase SPL from 16 MiB * bank_sel address.
+ */
+static int clean_bar(struct spi_nor *nor)
+{
+ u8 cmd, bank_sel = 0;
+
+ if (nor->bank_curr == 0)
+ return 0;
+ cmd = nor->bank_write_cmd;
+ nor->bank_curr = 0;
+ write_enable(nor);
+
+ return nor->write_reg(nor, cmd, &bank_sel, 1);
+}
+
+static int write_bar(struct spi_nor *nor, u32 offset)
+{
+ u8 cmd, bank_sel;
+ int ret;
+
+ bank_sel = offset / SZ_16M;
+ if (bank_sel == nor->bank_curr)
+ goto bar_end;
+
+ cmd = nor->bank_write_cmd;
+ write_enable(nor);
+ ret = nor->write_reg(nor, cmd, &bank_sel, 1);
+ if (ret < 0) {
+ debug("SF: fail to write bank register\n");
+ return ret;
+ }
+
+bar_end:
+ nor->bank_curr = bank_sel;
+ return nor->bank_curr;
+}
+
+static int read_bar(struct spi_nor *nor, const struct flash_info *info)
+{
+ u8 curr_bank = 0;
+ int ret;
+
+ switch (JEDEC_MFR(info)) {
+ case SNOR_MFR_SPANSION:
+ nor->bank_read_cmd = SPINOR_OP_BRRD;
+ nor->bank_write_cmd = SPINOR_OP_BRWR;
+ break;
+ default:
+ nor->bank_read_cmd = SPINOR_OP_RDEAR;
+ nor->bank_write_cmd = SPINOR_OP_WREAR;
+ }
+
+ ret = nor->read_reg(nor, nor->bank_read_cmd,
+ &curr_bank, 1);
+ if (ret) {
+ debug("SF: fail to read bank addr register\n");
+ return ret;
+ }
+ nor->bank_curr = curr_bank;
+
+ return 0;
+}
+#endif
+
/*
* Initiate the erasure of a single sector
*/
@@ -545,6 +565,11 @@ static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
len = instr->len;
while (len) {
+#ifdef CONFIG_SPI_FLASH_BAR
+ ret = write_bar(nor, addr);
+ if (ret < 0)
+ return ret;
+#endif
write_enable(nor);
ret = spi_nor_erase_sector(nor, addr);
@@ -559,9 +584,12 @@ static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
goto erase_err;
}
+erase_err:
+#ifdef CONFIG_SPI_FLASH_BAR
+ ret = clean_bar(nor);
+#endif
write_disable(nor);
-erase_err:
return ret;
}
@@ -1140,14 +1168,33 @@ static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
size_t *retlen, u_char *buf)
{
struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ struct spi_slave *spi = nor->spi;
int ret;
dev_dbg(nor->dev, "from 0x%08x, len %zd\n", (u32)from, len);
while (len) {
loff_t addr = from;
+ size_t read_len = len;
+
+#ifdef CONFIG_SPI_FLASH_BAR
+ u32 remain_len;
+
+ ret = write_bar(nor, addr);
+ if (ret < 0)
+ return log_ret(ret);
+ remain_len = (SZ_16M * (nor->bank_curr + 1)) - addr;
+
+ if (len < remain_len)
+ read_len = len;
+ else
+ read_len = remain_len;
+#endif
+
+ if (spi->max_read_size)
+ read_len = min(read_len, (size_t)spi->max_read_size);
- ret = nor->read(nor, addr, len, buf);
+ ret = nor->read(nor, addr, read_len, buf);
if (ret == 0) {
/* We shouldn't see 0-length reads */
ret = -EIO;
@@ -1164,18 +1211,49 @@ static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
ret = 0;
read_err:
+#ifdef CONFIG_SPI_FLASH_BAR
+ ret = clean_bar(nor);
+#endif
return ret;
}
#ifdef CONFIG_SPI_FLASH_SST
+static int sst_write_byteprogram(struct spi_nor *nor, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+{
+ size_t actual;
+ int ret = 0;
+
+ for (actual = 0; actual < len; actual++) {
+ nor->program_opcode = SPINOR_OP_BP;
+
+ write_enable(nor);
+ /* write one byte. */
+ ret = nor->write(nor, to, 1, buf + actual);
+ if (ret < 0)
+ goto sst_write_err;
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto sst_write_err;
+ to++;
+ }
+
+sst_write_err:
+ write_disable(nor);
+ return ret;
+}
+
static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
size_t *retlen, const u_char *buf)
{
struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ struct spi_slave *spi = nor->spi;
size_t actual;
int ret;
dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+ if (spi->mode & SPI_TX_BYTE)
+ return sst_write_byteprogram(nor, to, len, retlen, buf);
write_enable(nor);
@@ -1245,6 +1323,7 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
size_t *retlen, const u_char *buf)
{
struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ struct spi_slave *spi = nor->spi;
size_t page_offset, page_remain, i;
ssize_t ret;
@@ -1273,6 +1352,16 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
page_remain = min_t(size_t,
nor->page_size - page_offset, len - i);
+ if (spi->max_write_size)
+ page_remain = min(page_remain,
+ (size_t)(spi->max_write_size -
+ (nor->addr_width + 1)));
+
+#ifdef CONFIG_SPI_FLASH_BAR
+ ret = write_bar(nor, addr);
+ if (ret < 0)
+ return ret;
+#endif
write_enable(nor);
ret = nor->write(nor, addr, page_remain, buf + i);
if (ret < 0)
@@ -1291,6 +1380,9 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
}
write_err:
+#ifdef CONFIG_SPI_FLASH_BAR
+ ret = clean_bar(nor);
+#endif
return ret;
}
@@ -2534,12 +2626,20 @@ int spi_nor_scan(struct spi_nor *nor)
/* already configured from SFDP */
} else if (info->addr_width) {
nor->addr_width = info->addr_width;
- } else if (mtd->size > 0x1000000) {
+ } else if (mtd->size > SZ_16M) {
+#ifndef CONFIG_SPI_FLASH_BAR
/* enable 4-byte addressing if the device exceeds 16MiB */
nor->addr_width = 4;
if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
info->flags & SPI_NOR_4B_OPCODES)
spi_nor_set_4byte_opcodes(nor, info);
+#else
+ /* Configure the BAR - discover bank cmds and read current bank */
+ nor->addr_width = 3;
+ ret = read_bar(nor, info);
+ if (ret < 0)
+ return ret;
+#endif
} else {
nor->addr_width = 3;
}
diff --git a/drivers/spi/stm32_qspi.c b/drivers/spi/stm32_qspi.c
index 3b92254a5ce1..8b60d7c3b224 100644
--- a/drivers/spi/stm32_qspi.c
+++ b/drivers/spi/stm32_qspi.c
@@ -271,9 +271,9 @@ static void _stm32_qspi_enable_mmap(struct stm32_qspi_priv *priv,
{
unsigned int ccr_reg;
- priv->command = flash->read_cmd | CMD_HAS_ADR | CMD_HAS_DATA
+ priv->command = flash->read_opcode | CMD_HAS_ADR | CMD_HAS_DATA
| CMD_HAS_DUMMY;
- priv->dummycycles = flash->dummy_byte * 8;
+ priv->dummycycles = flash->read_dummy;
ccr_reg = _stm32_qspi_gen_ccr(priv, STM32_QSPI_CCR_MEM_MAP);
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 507458a76076..88e80af57941 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -105,6 +105,7 @@
/* Used for Spansion flashes only. */
#define SPINOR_OP_BRWR 0x17 /* Bank register write */
+#define SPINOR_OP_BRRD 0x16 /* Bank register read */
#define SPINOR_OP_CLSR 0x30 /* Clear status register 1 */
/* Used for Micron flashes only. */
@@ -256,6 +257,9 @@ struct flash_info;
* @read_opcode: the read opcode
* @read_dummy: the dummy needed by the read operation
* @program_opcode: the program opcode
+ * @bank_read_cmd: Bank read cmd
+ * @bank_write_cmd: Bank write cmd
+ * @bank_curr: Current flash bank
* @sst_write_second: used by the SST write operation
* @flags: flag options for the current SPI-NOR (SNOR_F_*)
* @read_proto: the SPI protocol for read operations
@@ -291,6 +295,11 @@ struct spi_nor {
u8 read_opcode;
u8 read_dummy;
u8 program_opcode;
+#ifdef CONFIG_SPI_FLASH_BAR
+ u8 bank_read_cmd;
+ u8 bank_write_cmd;
+ u8 bank_curr;
+#endif
enum spi_nor_protocol read_proto;
enum spi_nor_protocol write_proto;
enum spi_nor_protocol reg_proto;
diff --git a/include/spi_flash.h b/include/spi_flash.h
index e427e960d54f..7f691e8559cd 100644
--- a/include/spi_flash.h
+++ b/include/spi_flash.h
@@ -11,6 +11,7 @@
#include <dm.h> /* Because we dereference struct udevice here */
#include <linux/types.h>
+#include <linux/mtd/spi-nor.h>
#ifndef CONFIG_SF_DEFAULT_SPEED
# define CONFIG_SF_DEFAULT_SPEED 1000000
@@ -27,86 +28,6 @@
struct spi_slave;
-/**
- * struct spi_flash - SPI flash structure
- *
- * @spi: SPI slave
- * @dev: SPI flash device
- * @name: Name of SPI flash
- * @dual_flash: Indicates dual flash memories - dual stacked, parallel
- * @shift: Flash shift useful in dual parallel
- * @flags: Indication of spi flash flags
- * @size: Total flash size
- * @page_size: Write (page) size
- * @sector_size: Sector size
- * @erase_size: Erase size
- * @bank_read_cmd: Bank read cmd
- * @bank_write_cmd: Bank write cmd
- * @bank_curr: Current flash bank
- * @erase_cmd: Erase cmd 4K, 32K, 64K
- * @read_cmd: Read cmd - Array Fast, Extn read and quad read.
- * @write_cmd: Write cmd - page and quad program.
- * @dummy_byte: Dummy cycles for read operation.
- * @memory_map: Address of read-only SPI flash access
- * @flash_lock: lock a region of the SPI Flash
- * @flash_unlock: unlock a region of the SPI Flash
- * @flash_is_locked: check if a region of the SPI Flash is completely locked
- * @read: Flash read ops: Read len bytes at offset into buf
- * Supported cmds: Fast Array Read
- * @write: Flash write ops: Write len bytes from buf into offset
- * Supported cmds: Page Program
- * @erase: Flash erase ops: Erase len bytes from offset
- * Supported cmds: Sector erase 4K, 32K, 64K
- * return 0 - Success, 1 - Failure
- */
-struct spi_flash {
- struct spi_slave *spi;
-#ifdef CONFIG_DM_SPI_FLASH
- struct udevice *dev;
-#endif
- const char *name;
- u8 dual_flash;
- u8 shift;
- u16 flags;
-
- u32 size;
- u32 page_size;
- u32 sector_size;
- u32 erase_size;
-#ifdef CONFIG_SPI_FLASH_BAR
- u8 bank_read_cmd;
- u8 bank_write_cmd;
- u8 bank_curr;
-#endif
- u8 erase_cmd;
- u8 read_cmd;
- u8 write_cmd;
- u8 dummy_byte;
-
- void *memory_map;
-
- int (*flash_lock)(struct spi_flash *flash, u32 ofs, size_t len);
- int (*flash_unlock)(struct spi_flash *flash, u32 ofs, size_t len);
- int (*flash_is_locked)(struct spi_flash *flash, u32 ofs, size_t len);
-#ifndef CONFIG_DM_SPI_FLASH
- /*
- * These are not strictly needed for driver model, but keep them here
- * while the transition is in progress.
- *
- * Normally each driver would provide its own operations, but for
- * SPI flash most chips use the same algorithms. One approach is
- * to create a 'common' SPI flash device which knows how to talk
- * to most devices, and then allow other drivers to be used instead
- * if required, perhaps with a way of scanning through the list to
- * find the driver that matches the device.
- */
- int (*read)(struct spi_flash *flash, u32 offset, size_t len, void *buf);
- int (*write)(struct spi_flash *flash, u32 offset, size_t len,
- const void *buf);
- int (*erase)(struct spi_flash *flash, u32 offset, size_t len);
-#endif
-};
-
struct dm_spi_flash_ops {
int (*read)(struct udevice *dev, u32 offset, size_t len, void *buf);
int (*write)(struct udevice *dev, u32 offset, size_t len,
@@ -225,19 +146,37 @@ void spi_flash_free(struct spi_flash *flash);
static inline int spi_flash_read(struct spi_flash *flash, u32 offset,
size_t len, void *buf)
{
- return flash->read(flash, offset, len, buf);
+ struct mtd_info *mtd = &flash->mtd;
+ size_t retlen;
+
+ return mtd->_read(mtd, offset, len, &retlen, buf);
}
static inline int spi_flash_write(struct spi_flash *flash, u32 offset,
size_t len, const void *buf)
{
- return flash->write(flash, offset, len, buf);
+ struct mtd_info *mtd = &flash->mtd;
+ size_t retlen;
+
+ return mtd->_write(mtd, offset, len, &retlen, buf);
}
static inline int spi_flash_erase(struct spi_flash *flash, u32 offset,
size_t len)
{
- return flash->erase(flash, offset, len);
+ struct mtd_info *mtd = &flash->mtd;
+ struct erase_info instr;
+
+ if (offset % mtd->erasesize || len % mtd->erasesize) {
+ printf("SF: Erase offset/length not multiple of erase size\n");
+ return -EINVAL;
+ }
+
+ memset(&instr, 0, sizeof(instr));
+ instr.addr = offset;
+ instr.len = len;
+
+ return mtd->_erase(mtd, &instr);
}
#endif
--
2.20.1
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 06/11] mtd: spi: Remove unused files
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (4 preceding siblings ...)
2018-12-21 6:38 ` [U-Boot] [PATCH v2 05/11] mtd: spi: Switch to new SPI NOR framework Vignesh R
@ 2018-12-21 6:38 ` Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 07/11] mtd: spi: Add lightweight SPI flash stack for SPL Vignesh R
` (8 subsequent siblings)
14 siblings, 0 replies; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
spi_flash and spi_flash_ids are no longer needed after SPI NOR
migration. Remove them.
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
drivers/mtd/spi/spi_flash.c | 1337 -------------------------------
drivers/mtd/spi/spi_flash_ids.c | 211 -----
2 files changed, 1548 deletions(-)
delete mode 100644 drivers/mtd/spi/spi_flash.c
delete mode 100644 drivers/mtd/spi/spi_flash_ids.c
diff --git a/drivers/mtd/spi/spi_flash.c b/drivers/mtd/spi/spi_flash.c
deleted file mode 100644
index 0c2392f28a43..000000000000
--- a/drivers/mtd/spi/spi_flash.c
+++ /dev/null
@@ -1,1337 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * SPI Flash Core
- *
- * Copyright (C) 2015 Jagan Teki <jteki@openedev.com>
- * Copyright (C) 2013 Jagannadha Sutradharudu Teki, Xilinx Inc.
- * Copyright (C) 2010 Reinhard Meyer, EMK Elektronik
- * Copyright (C) 2008 Atmel Corporation
- */
-
-#include <common.h>
-#include <errno.h>
-#include <malloc.h>
-#include <mapmem.h>
-#include <spi.h>
-#include <spi_flash.h>
-#include <linux/log2.h>
-#include <linux/sizes.h>
-#include <dma.h>
-
-#include "sf_internal.h"
-
-static void spi_flash_addr(u32 addr, u8 *cmd)
-{
- /* cmd[0] is actual command */
- cmd[1] = addr >> 16;
- cmd[2] = addr >> 8;
- cmd[3] = addr >> 0;
-}
-
-static int read_sr(struct spi_flash *flash, u8 *rs)
-{
- int ret;
- u8 cmd;
-
- cmd = CMD_READ_STATUS;
- ret = spi_flash_read_common(flash, &cmd, 1, rs, 1);
- if (ret < 0) {
- debug("SF: fail to read status register\n");
- return ret;
- }
-
- return 0;
-}
-
-static int read_fsr(struct spi_flash *flash, u8 *fsr)
-{
- int ret;
- const u8 cmd = CMD_FLAG_STATUS;
-
- ret = spi_flash_read_common(flash, &cmd, 1, fsr, 1);
- if (ret < 0) {
- debug("SF: fail to read flag status register\n");
- return ret;
- }
-
- return 0;
-}
-
-static int write_sr(struct spi_flash *flash, u8 ws)
-{
- u8 cmd;
- int ret;
-
- cmd = CMD_WRITE_STATUS;
- ret = spi_flash_write_common(flash, &cmd, 1, &ws, 1);
- if (ret < 0) {
- debug("SF: fail to write status register\n");
- return ret;
- }
-
- return 0;
-}
-
-#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
-static int read_cr(struct spi_flash *flash, u8 *rc)
-{
- int ret;
- u8 cmd;
-
- cmd = CMD_READ_CONFIG;
- ret = spi_flash_read_common(flash, &cmd, 1, rc, 1);
- if (ret < 0) {
- debug("SF: fail to read config register\n");
- return ret;
- }
-
- return 0;
-}
-
-static int write_cr(struct spi_flash *flash, u8 wc)
-{
- u8 data[2];
- u8 cmd;
- int ret;
-
- ret = read_sr(flash, &data[0]);
- if (ret < 0)
- return ret;
-
- cmd = CMD_WRITE_STATUS;
- data[1] = wc;
- ret = spi_flash_write_common(flash, &cmd, 1, &data, 2);
- if (ret) {
- debug("SF: fail to write config register\n");
- return ret;
- }
-
- return 0;
-}
-#endif
-
-int spi_flash_cmd_get_sw_write_prot(struct spi_flash *flash)
-{
- u8 status;
- int ret;
-
- ret = read_sr(flash, &status);
- if (ret)
- return ret;
-
- return (status >> 2) & 7;
-}
-
-#ifdef CONFIG_SPI_FLASH_BAR
-/*
- * This "clean_bar" is necessary in a situation when one was accessing
- * spi flash memory > 16 MiB by using Bank Address Register's BA24 bit.
- *
- * After it the BA24 bit shall be cleared to allow access to correct
- * memory region after SW reset (by calling "reset" command).
- *
- * Otherwise, the BA24 bit may be left set and then after reset, the
- * ROM would read/write/erase SPL from 16 MiB * bank_sel address.
- */
-static int clean_bar(struct spi_flash *flash)
-{
- u8 cmd, bank_sel = 0;
-
- if (flash->bank_curr == 0)
- return 0;
- cmd = flash->bank_write_cmd;
- flash->bank_curr = 0;
-
- return spi_flash_write_common(flash, &cmd, 1, &bank_sel, 1);
-}
-
-static int write_bar(struct spi_flash *flash, u32 offset)
-{
- u8 cmd, bank_sel;
- int ret;
-
- bank_sel = offset / (SPI_FLASH_16MB_BOUN << flash->shift);
- if (bank_sel == flash->bank_curr)
- goto bar_end;
-
- cmd = flash->bank_write_cmd;
- ret = spi_flash_write_common(flash, &cmd, 1, &bank_sel, 1);
- if (ret < 0) {
- debug("SF: fail to write bank register\n");
- return ret;
- }
-
-bar_end:
- flash->bank_curr = bank_sel;
- return flash->bank_curr;
-}
-
-static int read_bar(struct spi_flash *flash, const struct spi_flash_info *info)
-{
- u8 curr_bank = 0;
- int ret;
-
- if (flash->size <= SPI_FLASH_16MB_BOUN)
- goto bar_end;
-
- switch (JEDEC_MFR(info)) {
- case SPI_FLASH_CFI_MFR_SPANSION:
- flash->bank_read_cmd = CMD_BANKADDR_BRRD;
- flash->bank_write_cmd = CMD_BANKADDR_BRWR;
- break;
- default:
- flash->bank_read_cmd = CMD_EXTNADDR_RDEAR;
- flash->bank_write_cmd = CMD_EXTNADDR_WREAR;
- }
-
- ret = spi_flash_read_common(flash, &flash->bank_read_cmd, 1,
- &curr_bank, 1);
- if (ret) {
- debug("SF: fail to read bank addr register\n");
- return ret;
- }
-
-bar_end:
- flash->bank_curr = curr_bank;
- return 0;
-}
-#endif
-
-#ifdef CONFIG_SF_DUAL_FLASH
-static void spi_flash_dual(struct spi_flash *flash, u32 *addr)
-{
- switch (flash->dual_flash) {
- case SF_DUAL_STACKED_FLASH:
- if (*addr >= (flash->size >> 1)) {
- *addr -= flash->size >> 1;
- flash->flags |= SNOR_F_USE_UPAGE;
- } else {
- flash->flags &= ~SNOR_F_USE_UPAGE;
- }
- break;
- case SF_DUAL_PARALLEL_FLASH:
- *addr >>= flash->shift;
- break;
- default:
- debug("SF: Unsupported dual_flash=%d\n", flash->dual_flash);
- break;
- }
-}
-#endif
-
-static int spi_flash_sr_ready(struct spi_flash *flash)
-{
- u8 sr;
- int ret;
-
- ret = read_sr(flash, &sr);
- if (ret < 0)
- return ret;
-
- return !(sr & STATUS_WIP);
-}
-
-static int spi_flash_fsr_ready(struct spi_flash *flash)
-{
- u8 fsr;
- int ret;
-
- ret = read_fsr(flash, &fsr);
- if (ret < 0)
- return ret;
-
- return fsr & STATUS_PEC;
-}
-
-static int spi_flash_ready(struct spi_flash *flash)
-{
- int sr, fsr;
-
- sr = spi_flash_sr_ready(flash);
- if (sr < 0)
- return sr;
-
- fsr = 1;
- if (flash->flags & SNOR_F_USE_FSR) {
- fsr = spi_flash_fsr_ready(flash);
- if (fsr < 0)
- return fsr;
- }
-
- return sr && fsr;
-}
-
-static int spi_flash_wait_till_ready(struct spi_flash *flash,
- unsigned long timeout)
-{
- unsigned long timebase;
- int ret;
-
- timebase = get_timer(0);
-
- while (get_timer(timebase) < timeout) {
- ret = spi_flash_ready(flash);
- if (ret < 0)
- return ret;
- if (ret)
- return 0;
- }
-
- printf("SF: Timeout!\n");
-
- return -ETIMEDOUT;
-}
-
-int spi_flash_write_common(struct spi_flash *flash, const u8 *cmd,
- size_t cmd_len, const void *buf, size_t buf_len)
-{
- struct spi_slave *spi = flash->spi;
- unsigned long timeout = SPI_FLASH_PROG_TIMEOUT;
- int ret;
-
- if (buf == NULL)
- timeout = SPI_FLASH_PAGE_ERASE_TIMEOUT;
-
- ret = spi_claim_bus(spi);
- if (ret) {
- debug("SF: unable to claim SPI bus\n");
- return ret;
- }
-
- ret = spi_flash_cmd_write_enable(flash);
- if (ret < 0) {
- debug("SF: enabling write failed\n");
- return ret;
- }
-
- ret = spi_flash_cmd_write(spi, cmd, cmd_len, buf, buf_len);
- if (ret < 0) {
- debug("SF: write cmd failed\n");
- return ret;
- }
-
- ret = spi_flash_wait_till_ready(flash, timeout);
- if (ret < 0) {
- debug("SF: write %s timed out\n",
- timeout == SPI_FLASH_PROG_TIMEOUT ?
- "program" : "page erase");
- return ret;
- }
-
- spi_release_bus(spi);
-
- return ret;
-}
-
-int spi_flash_cmd_erase_ops(struct spi_flash *flash, u32 offset, size_t len)
-{
- u32 erase_size, erase_addr;
- u8 cmd[SPI_FLASH_CMD_LEN];
- int ret = -1;
-
- erase_size = flash->erase_size;
- if (offset % erase_size || len % erase_size) {
- printf("SF: Erase offset/length not multiple of erase size\n");
- return -1;
- }
-
- if (flash->flash_is_locked) {
- if (flash->flash_is_locked(flash, offset, len) > 0) {
- printf("offset 0x%x is protected and cannot be erased\n",
- offset);
- return -EINVAL;
- }
- }
-
- cmd[0] = flash->erase_cmd;
- while (len) {
- erase_addr = offset;
-
-#ifdef CONFIG_SF_DUAL_FLASH
- if (flash->dual_flash > SF_SINGLE_FLASH)
- spi_flash_dual(flash, &erase_addr);
-#endif
-#ifdef CONFIG_SPI_FLASH_BAR
- ret = write_bar(flash, erase_addr);
- if (ret < 0)
- return ret;
-#endif
- spi_flash_addr(erase_addr, cmd);
-
- debug("SF: erase %2x %2x %2x %2x (%x)\n", cmd[0], cmd[1],
- cmd[2], cmd[3], erase_addr);
-
- ret = spi_flash_write_common(flash, cmd, sizeof(cmd), NULL, 0);
- if (ret < 0) {
- debug("SF: erase failed\n");
- break;
- }
-
- offset += erase_size;
- len -= erase_size;
- }
-
-#ifdef CONFIG_SPI_FLASH_BAR
- ret = clean_bar(flash);
-#endif
-
- return ret;
-}
-
-int spi_flash_cmd_write_ops(struct spi_flash *flash, u32 offset,
- size_t len, const void *buf)
-{
- struct spi_slave *spi = flash->spi;
- unsigned long byte_addr, page_size;
- u32 write_addr;
- size_t chunk_len, actual;
- u8 cmd[SPI_FLASH_CMD_LEN];
- int ret = -1;
-
- page_size = flash->page_size;
-
- if (flash->flash_is_locked) {
- if (flash->flash_is_locked(flash, offset, len) > 0) {
- printf("offset 0x%x is protected and cannot be written\n",
- offset);
- return -EINVAL;
- }
- }
-
- cmd[0] = flash->write_cmd;
- for (actual = 0; actual < len; actual += chunk_len) {
- write_addr = offset;
-
-#ifdef CONFIG_SF_DUAL_FLASH
- if (flash->dual_flash > SF_SINGLE_FLASH)
- spi_flash_dual(flash, &write_addr);
-#endif
-#ifdef CONFIG_SPI_FLASH_BAR
- ret = write_bar(flash, write_addr);
- if (ret < 0)
- return ret;
-#endif
- byte_addr = offset % page_size;
- chunk_len = min(len - actual, (size_t)(page_size - byte_addr));
-
- if (spi->max_write_size)
- chunk_len = min(chunk_len,
- spi->max_write_size - sizeof(cmd));
-
- spi_flash_addr(write_addr, cmd);
-
- debug("SF: 0x%p => cmd = { 0x%02x 0x%02x%02x%02x } chunk_len = %zu\n",
- buf + actual, cmd[0], cmd[1], cmd[2], cmd[3], chunk_len);
-
- ret = spi_flash_write_common(flash, cmd, sizeof(cmd),
- buf + actual, chunk_len);
- if (ret < 0) {
- debug("SF: write failed\n");
- break;
- }
-
- offset += chunk_len;
- }
-
-#ifdef CONFIG_SPI_FLASH_BAR
- ret = clean_bar(flash);
-#endif
-
- return ret;
-}
-
-int spi_flash_read_common(struct spi_flash *flash, const u8 *cmd,
- size_t cmd_len, void *data, size_t data_len)
-{
- struct spi_slave *spi = flash->spi;
- int ret;
-
- ret = spi_claim_bus(spi);
- if (ret) {
- debug("SF: unable to claim SPI bus\n");
- return ret;
- }
-
- ret = spi_flash_cmd_read(spi, cmd, cmd_len, data, data_len);
- if (ret < 0) {
- debug("SF: read cmd failed\n");
- return ret;
- }
-
- spi_release_bus(spi);
-
- return ret;
-}
-
-/*
- * TODO: remove the weak after all the other spi_flash_copy_mmap
- * implementations removed from drivers
- */
-void __weak spi_flash_copy_mmap(void *data, void *offset, size_t len)
-{
-#ifdef CONFIG_DMA
- if (!dma_memcpy(data, offset, len))
- return;
-#endif
- memcpy(data, offset, len);
-}
-
-int spi_flash_cmd_read_ops(struct spi_flash *flash, u32 offset,
- size_t len, void *data)
-{
- struct spi_slave *spi = flash->spi;
- u8 cmdsz;
- u32 remain_len, read_len, read_addr;
- int bank_sel = 0;
- int ret = 0;
-
- /* Handle memory-mapped SPI */
- if (flash->memory_map) {
- ret = spi_claim_bus(spi);
- if (ret) {
- debug("SF: unable to claim SPI bus\n");
- return log_ret(ret);
- }
- spi_xfer(spi, 0, NULL, NULL, SPI_XFER_MMAP);
- spi_flash_copy_mmap(data, flash->memory_map + offset, len);
- spi_xfer(spi, 0, NULL, NULL, SPI_XFER_MMAP_END);
- spi_release_bus(spi);
- return 0;
- }
-
- cmdsz = SPI_FLASH_CMD_LEN + flash->dummy_byte;
- u8 cmd[cmdsz];
-
- cmd[0] = flash->read_cmd;
- while (len) {
- read_addr = offset;
-
-#ifdef CONFIG_SF_DUAL_FLASH
- if (flash->dual_flash > SF_SINGLE_FLASH)
- spi_flash_dual(flash, &read_addr);
-#endif
-#ifdef CONFIG_SPI_FLASH_BAR
- ret = write_bar(flash, read_addr);
- if (ret < 0)
- return log_ret(ret);
- bank_sel = flash->bank_curr;
-#endif
- remain_len = ((SPI_FLASH_16MB_BOUN << flash->shift) *
- (bank_sel + 1)) - offset;
- if (len < remain_len)
- read_len = len;
- else
- read_len = remain_len;
-
- if (spi->max_read_size)
- read_len = min(read_len, spi->max_read_size);
-
- spi_flash_addr(read_addr, cmd);
-
- ret = spi_flash_read_common(flash, cmd, cmdsz, data, read_len);
- if (ret < 0) {
- debug("SF: read failed\n");
- break;
- }
-
- offset += read_len;
- len -= read_len;
- data += read_len;
- }
-
-#ifdef CONFIG_SPI_FLASH_BAR
- ret = clean_bar(flash);
-#endif
-
- return log_ret(ret);
-}
-
-#ifdef CONFIG_SPI_FLASH_SST
-static bool sst26_process_bpr(u32 bpr_size, u8 *cmd, u32 bit, enum lock_ctl ctl)
-{
- switch (ctl) {
- case SST26_CTL_LOCK:
- cmd[bpr_size - (bit / 8) - 1] |= BIT(bit % 8);
- break;
- case SST26_CTL_UNLOCK:
- cmd[bpr_size - (bit / 8) - 1] &= ~BIT(bit % 8);
- break;
- case SST26_CTL_CHECK:
- return !!(cmd[bpr_size - (bit / 8) - 1] & BIT(bit % 8));
- }
-
- return false;
-}
-
-/*
- * sst26wf016/sst26wf032/sst26wf064 have next block protection:
- * 4x - 8 KByte blocks - read & write protection bits - upper addresses
- * 1x - 32 KByte blocks - write protection bits
- * rest - 64 KByte blocks - write protection bits
- * 1x - 32 KByte blocks - write protection bits
- * 4x - 8 KByte blocks - read & write protection bits - lower addresses
- *
- * We'll support only per 64k lock/unlock so lower and upper 64 KByte region
- * will be treated as single block.
- */
-
-/*
- * Lock, unlock or check lock status of the flash region of the flash (depending
- * on the lock_ctl value)
- */
-static int sst26_lock_ctl(struct spi_flash *flash, u32 ofs, size_t len, enum lock_ctl ctl)
-{
- u32 i, bpr_ptr, rptr_64k, lptr_64k, bpr_size;
- bool lower_64k = false, upper_64k = false;
- u8 cmd, bpr_buff[SST26_MAX_BPR_REG_LEN] = {};
- int ret;
-
- /* Check length and offset for 64k alignment */
- if ((ofs & (SZ_64K - 1)) || (len & (SZ_64K - 1)))
- return -EINVAL;
-
- if (ofs + len > flash->size)
- return -EINVAL;
-
- /* SST26 family has only 16 Mbit, 32 Mbit and 64 Mbit IC */
- if (flash->size != SZ_2M &&
- flash->size != SZ_4M &&
- flash->size != SZ_8M)
- return -EINVAL;
-
- bpr_size = 2 + (flash->size / SZ_64K / 8);
-
- cmd = SST26_CMD_READ_BPR;
- ret = spi_flash_read_common(flash, &cmd, 1, bpr_buff, bpr_size);
- if (ret < 0) {
- printf("SF: fail to read block-protection register\n");
- return ret;
- }
-
- rptr_64k = min_t(u32, ofs + len , flash->size - SST26_BOUND_REG_SIZE);
- lptr_64k = max_t(u32, ofs, SST26_BOUND_REG_SIZE);
-
- upper_64k = ((ofs + len) > (flash->size - SST26_BOUND_REG_SIZE));
- lower_64k = (ofs < SST26_BOUND_REG_SIZE);
-
- /* Lower bits in block-protection register are about 64k region */
- bpr_ptr = lptr_64k / SZ_64K - 1;
-
- /* Process 64K blocks region */
- while (lptr_64k < rptr_64k) {
- if (sst26_process_bpr(bpr_size, bpr_buff, bpr_ptr, ctl))
- return EACCES;
-
- bpr_ptr++;
- lptr_64k += SZ_64K;
- }
-
- /* 32K and 8K region bits in BPR are after 64k region bits */
- bpr_ptr = (flash->size - 2 * SST26_BOUND_REG_SIZE) / SZ_64K;
-
- /* Process lower 32K block region */
- if (lower_64k)
- if (sst26_process_bpr(bpr_size, bpr_buff, bpr_ptr, ctl))
- return EACCES;
-
- bpr_ptr++;
-
- /* Process upper 32K block region */
- if (upper_64k)
- if (sst26_process_bpr(bpr_size, bpr_buff, bpr_ptr, ctl))
- return EACCES;
-
- bpr_ptr++;
-
- /* Process lower 8K block regions */
- for (i = 0; i < SST26_BPR_8K_NUM; i++) {
- if (lower_64k)
- if (sst26_process_bpr(bpr_size, bpr_buff, bpr_ptr, ctl))
- return EACCES;
-
- /* In 8K area BPR has both read and write protection bits */
- bpr_ptr += 2;
- }
-
- /* Process upper 8K block regions */
- for (i = 0; i < SST26_BPR_8K_NUM; i++) {
- if (upper_64k)
- if (sst26_process_bpr(bpr_size, bpr_buff, bpr_ptr, ctl))
- return EACCES;
-
- /* In 8K area BPR has both read and write protection bits */
- bpr_ptr += 2;
- }
-
- /* If we check region status we don't need to write BPR back */
- if (ctl == SST26_CTL_CHECK)
- return 0;
-
- cmd = SST26_CMD_WRITE_BPR;
- ret = spi_flash_write_common(flash, &cmd, 1, bpr_buff, bpr_size);
- if (ret < 0) {
- printf("SF: fail to write block-protection register\n");
- return ret;
- }
-
- return 0;
-}
-
-static int sst26_unlock(struct spi_flash *flash, u32 ofs, size_t len)
-{
- return sst26_lock_ctl(flash, ofs, len, SST26_CTL_UNLOCK);
-}
-
-static int sst26_lock(struct spi_flash *flash, u32 ofs, size_t len)
-{
- return sst26_lock_ctl(flash, ofs, len, SST26_CTL_LOCK);
-}
-
-/*
- * Returns EACCES (positive value) if region is locked, 0 if region is unlocked,
- * and negative on errors.
- */
-static int sst26_is_locked(struct spi_flash *flash, u32 ofs, size_t len)
-{
- /*
- * is_locked function is used for check before reading or erasing flash
- * region, so offset and length might be not 64k allighned, so adjust
- * them to be 64k allighned as sst26_lock_ctl works only with 64k
- * allighned regions.
- */
- ofs -= ofs & (SZ_64K - 1);
- len = len & (SZ_64K - 1) ? (len & ~(SZ_64K - 1)) + SZ_64K : len;
-
- return sst26_lock_ctl(flash, ofs, len, SST26_CTL_CHECK);
-}
-
-static int sst_byte_write(struct spi_flash *flash, u32 offset, const void *buf)
-{
- struct spi_slave *spi = flash->spi;
- int ret;
- u8 cmd[4] = {
- CMD_SST_BP,
- offset >> 16,
- offset >> 8,
- offset,
- };
-
- debug("BP[%02x]: 0x%p => cmd = { 0x%02x 0x%06x }\n",
- spi_w8r8(spi, CMD_READ_STATUS), buf, cmd[0], offset);
-
- ret = spi_flash_cmd_write_enable(flash);
- if (ret)
- return ret;
-
- ret = spi_flash_cmd_write(spi, cmd, sizeof(cmd), buf, 1);
- if (ret)
- return ret;
-
- return spi_flash_wait_till_ready(flash, SPI_FLASH_PROG_TIMEOUT);
-}
-
-int sst_write_wp(struct spi_flash *flash, u32 offset, size_t len,
- const void *buf)
-{
- struct spi_slave *spi = flash->spi;
- size_t actual, cmd_len;
- int ret;
- u8 cmd[4];
-
- ret = spi_claim_bus(spi);
- if (ret) {
- debug("SF: Unable to claim SPI bus\n");
- return ret;
- }
-
- /* If the data is not word aligned, write out leading single byte */
- actual = offset % 2;
- if (actual) {
- ret = sst_byte_write(flash, offset, buf);
- if (ret)
- goto done;
- }
- offset += actual;
-
- ret = spi_flash_cmd_write_enable(flash);
- if (ret)
- goto done;
-
- cmd_len = 4;
- cmd[0] = CMD_SST_AAI_WP;
- cmd[1] = offset >> 16;
- cmd[2] = offset >> 8;
- cmd[3] = offset;
-
- for (; actual < len - 1; actual += 2) {
- debug("WP[%02x]: 0x%p => cmd = { 0x%02x 0x%06x }\n",
- spi_w8r8(spi, CMD_READ_STATUS), buf + actual,
- cmd[0], offset);
-
- ret = spi_flash_cmd_write(spi, cmd, cmd_len,
- buf + actual, 2);
- if (ret) {
- debug("SF: sst word program failed\n");
- break;
- }
-
- ret = spi_flash_wait_till_ready(flash, SPI_FLASH_PROG_TIMEOUT);
- if (ret)
- break;
-
- cmd_len = 1;
- offset += 2;
- }
-
- if (!ret)
- ret = spi_flash_cmd_write_disable(flash);
-
- /* If there is a single trailing byte, write it out */
- if (!ret && actual != len)
- ret = sst_byte_write(flash, offset, buf + actual);
-
- done:
- debug("SF: sst: program %s %zu bytes @ 0x%zx\n",
- ret ? "failure" : "success", len, offset - actual);
-
- spi_release_bus(spi);
- return ret;
-}
-
-int sst_write_bp(struct spi_flash *flash, u32 offset, size_t len,
- const void *buf)
-{
- struct spi_slave *spi = flash->spi;
- size_t actual;
- int ret;
-
- ret = spi_claim_bus(spi);
- if (ret) {
- debug("SF: Unable to claim SPI bus\n");
- return ret;
- }
-
- for (actual = 0; actual < len; actual++) {
- ret = sst_byte_write(flash, offset, buf + actual);
- if (ret) {
- debug("SF: sst byte program failed\n");
- break;
- }
- offset++;
- }
-
- if (!ret)
- ret = spi_flash_cmd_write_disable(flash);
-
- debug("SF: sst: program %s %zu bytes @ 0x%zx\n",
- ret ? "failure" : "success", len, offset - actual);
-
- spi_release_bus(spi);
- return ret;
-}
-#endif
-
-#if defined(CONFIG_SPI_FLASH_STMICRO) || defined(CONFIG_SPI_FLASH_SST)
-static void stm_get_locked_range(struct spi_flash *flash, u8 sr, loff_t *ofs,
- u64 *len)
-{
- u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
- int shift = ffs(mask) - 1;
- int pow;
-
- if (!(sr & mask)) {
- /* No protection */
- *ofs = 0;
- *len = 0;
- } else {
- pow = ((sr & mask) ^ mask) >> shift;
- *len = flash->size >> pow;
- *ofs = flash->size - *len;
- }
-}
-
-/*
- * Return 1 if the entire region is locked, 0 otherwise
- */
-static int stm_is_locked_sr(struct spi_flash *flash, loff_t ofs, u64 len,
- u8 sr)
-{
- loff_t lock_offs;
- u64 lock_len;
-
- stm_get_locked_range(flash, sr, &lock_offs, &lock_len);
-
- return (ofs + len <= lock_offs + lock_len) && (ofs >= lock_offs);
-}
-
-/*
- * Check if a region of the flash is (completely) locked. See stm_lock() for
- * more info.
- *
- * Returns 1 if entire region is locked, 0 if any portion is unlocked, and
- * negative on errors.
- */
-int stm_is_locked(struct spi_flash *flash, u32 ofs, size_t len)
-{
- int status;
- u8 sr;
-
- status = read_sr(flash, &sr);
- if (status < 0)
- return status;
-
- return stm_is_locked_sr(flash, ofs, len, sr);
-}
-
-/*
- * Lock a region of the flash. Compatible with ST Micro and similar flash.
- * Supports only the block protection bits BP{0,1,2} in the status register
- * (SR). Does not support these features found in newer SR bitfields:
- * - TB: top/bottom protect - only handle TB=0 (top protect)
- * - SEC: sector/block protect - only handle SEC=0 (block protect)
- * - CMP: complement protect - only support CMP=0 (range is not complemented)
- *
- * Sample table portion for 8MB flash (Winbond w25q64fw):
- *
- * SEC | TB | BP2 | BP1 | BP0 | Prot Length | Protected Portion
- * --------------------------------------------------------------------------
- * X | X | 0 | 0 | 0 | NONE | NONE
- * 0 | 0 | 0 | 0 | 1 | 128 KB | Upper 1/64
- * 0 | 0 | 0 | 1 | 0 | 256 KB | Upper 1/32
- * 0 | 0 | 0 | 1 | 1 | 512 KB | Upper 1/16
- * 0 | 0 | 1 | 0 | 0 | 1 MB | Upper 1/8
- * 0 | 0 | 1 | 0 | 1 | 2 MB | Upper 1/4
- * 0 | 0 | 1 | 1 | 0 | 4 MB | Upper 1/2
- * X | X | 1 | 1 | 1 | 8 MB | ALL
- *
- * Returns negative on errors, 0 on success.
- */
-int stm_lock(struct spi_flash *flash, u32 ofs, size_t len)
-{
- u8 status_old, status_new;
- u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
- u8 shift = ffs(mask) - 1, pow, val;
- int ret;
-
- ret = read_sr(flash, &status_old);
- if (ret < 0)
- return ret;
-
- /* SPI NOR always locks to the end */
- if (ofs + len != flash->size) {
- /* Does combined region extend to end? */
- if (!stm_is_locked_sr(flash, ofs + len, flash->size - ofs - len,
- status_old))
- return -EINVAL;
- len = flash->size - ofs;
- }
-
- /*
- * Need smallest pow such that:
- *
- * 1 / (2^pow) <= (len / size)
- *
- * so (assuming power-of-2 size) we do:
- *
- * pow = ceil(log2(size / len)) = log2(size) - floor(log2(len))
- */
- pow = ilog2(flash->size) - ilog2(len);
- val = mask - (pow << shift);
- if (val & ~mask)
- return -EINVAL;
-
- /* Don't "lock" with no region! */
- if (!(val & mask))
- return -EINVAL;
-
- status_new = (status_old & ~mask) | val;
-
- /* Only modify protection if it will not unlock other areas */
- if ((status_new & mask) <= (status_old & mask))
- return -EINVAL;
-
- write_sr(flash, status_new);
-
- return 0;
-}
-
-/*
- * Unlock a region of the flash. See stm_lock() for more info
- *
- * Returns negative on errors, 0 on success.
- */
-int stm_unlock(struct spi_flash *flash, u32 ofs, size_t len)
-{
- uint8_t status_old, status_new;
- u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
- u8 shift = ffs(mask) - 1, pow, val;
- int ret;
-
- ret = read_sr(flash, &status_old);
- if (ret < 0)
- return ret;
-
- /* Cannot unlock; would unlock larger region than requested */
- if (stm_is_locked_sr(flash, ofs - flash->erase_size, flash->erase_size,
- status_old))
- return -EINVAL;
- /*
- * Need largest pow such that:
- *
- * 1 / (2^pow) >= (len / size)
- *
- * so (assuming power-of-2 size) we do:
- *
- * pow = floor(log2(size / len)) = log2(size) - ceil(log2(len))
- */
- pow = ilog2(flash->size) - order_base_2(flash->size - (ofs + len));
- if (ofs + len == flash->size) {
- val = 0; /* fully unlocked */
- } else {
- val = mask - (pow << shift);
- /* Some power-of-two sizes are not supported */
- if (val & ~mask)
- return -EINVAL;
- }
-
- status_new = (status_old & ~mask) | val;
-
- /* Only modify protection if it will not lock other areas */
- if ((status_new & mask) >= (status_old & mask))
- return -EINVAL;
-
- write_sr(flash, status_new);
-
- return 0;
-}
-#endif
-
-
-#ifdef CONFIG_SPI_FLASH_MACRONIX
-static int macronix_quad_enable(struct spi_flash *flash)
-{
- u8 qeb_status;
- int ret;
-
- ret = read_sr(flash, &qeb_status);
- if (ret < 0)
- return ret;
-
- if (qeb_status & STATUS_QEB_MXIC)
- return 0;
-
- ret = write_sr(flash, qeb_status | STATUS_QEB_MXIC);
- if (ret < 0)
- return ret;
-
- /* read SR and check it */
- ret = read_sr(flash, &qeb_status);
- if (!(ret >= 0 && (qeb_status & STATUS_QEB_MXIC))) {
- printf("SF: Macronix SR Quad bit not clear\n");
- return -EINVAL;
- }
-
- return ret;
-}
-#endif
-
-#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
-static int spansion_quad_enable(struct spi_flash *flash)
-{
- u8 qeb_status;
- int ret;
-
- ret = read_cr(flash, &qeb_status);
- if (ret < 0)
- return ret;
-
- if (qeb_status & STATUS_QEB_WINSPAN)
- return 0;
-
- ret = write_cr(flash, qeb_status | STATUS_QEB_WINSPAN);
- if (ret < 0)
- return ret;
-
- /* read CR and check it */
- ret = read_cr(flash, &qeb_status);
- if (!(ret >= 0 && (qeb_status & STATUS_QEB_WINSPAN))) {
- printf("SF: Spansion CR Quad bit not clear\n");
- return -EINVAL;
- }
-
- return ret;
-}
-#endif
-
-static const struct spi_flash_info *spi_flash_read_id(struct spi_flash *flash)
-{
- int tmp;
- u8 id[SPI_FLASH_MAX_ID_LEN];
- const struct spi_flash_info *info;
-
- tmp = spi_flash_cmd(flash->spi, CMD_READ_ID, id, SPI_FLASH_MAX_ID_LEN);
- if (tmp < 0) {
- printf("SF: error %d reading JEDEC ID\n", tmp);
- return ERR_PTR(tmp);
- }
-
- info = spi_flash_ids;
- for (; info->name != NULL; info++) {
- if (info->id_len) {
- if (!memcmp(info->id, id, info->id_len))
- return info;
- }
- }
-
- printf("SF: unrecognized JEDEC id bytes: %02x, %02x, %02x\n",
- id[0], id[1], id[2]);
- return ERR_PTR(-ENODEV);
-}
-
-static int set_quad_mode(struct spi_flash *flash,
- const struct spi_flash_info *info)
-{
- switch (JEDEC_MFR(info)) {
-#ifdef CONFIG_SPI_FLASH_MACRONIX
- case SPI_FLASH_CFI_MFR_MACRONIX:
- return macronix_quad_enable(flash);
-#endif
-#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
- case SPI_FLASH_CFI_MFR_SPANSION:
- case SPI_FLASH_CFI_MFR_WINBOND:
- return spansion_quad_enable(flash);
-#endif
-#ifdef CONFIG_SPI_FLASH_STMICRO
- case SPI_FLASH_CFI_MFR_STMICRO:
- case SPI_FLASH_CFI_MFR_MICRON:
- debug("SF: QEB is volatile for %02x flash\n", JEDEC_MFR(info));
- return 0;
-#endif
- default:
- printf("SF: Need set QEB func for %02x flash\n",
- JEDEC_MFR(info));
- return -1;
- }
-}
-
-#if CONFIG_IS_ENABLED(OF_CONTROL)
-int spi_flash_decode_fdt(struct spi_flash *flash)
-{
-#ifdef CONFIG_DM_SPI_FLASH
- fdt_addr_t addr;
- fdt_size_t size;
-
- addr = dev_read_addr_size(flash->dev, "memory-map", &size);
- if (addr == FDT_ADDR_T_NONE) {
- debug("%s: Cannot decode address\n", __func__);
- return 0;
- }
-
- if (flash->size > size) {
- debug("%s: Memory map must cover entire device\n", __func__);
- return -1;
- }
- flash->memory_map = map_sysmem(addr, size);
-#endif
-
- return 0;
-}
-#endif /* CONFIG_IS_ENABLED(OF_CONTROL) */
-
-int spi_flash_scan(struct spi_flash *flash)
-{
- struct spi_slave *spi = flash->spi;
- const struct spi_flash_info *info = NULL;
- int ret;
-
- info = spi_flash_read_id(flash);
- if (IS_ERR_OR_NULL(info))
- return -ENOENT;
-
- /*
- * Flash powers up read-only, so clear BP# bits.
- *
- * Note on some flash (like Macronix), QE (quad enable) bit is in the
- * same status register as BP# bits, and we need preserve its original
- * value during a reboot cycle as this is required by some platforms
- * (like Intel ICH SPI controller working under descriptor mode).
- */
- if (JEDEC_MFR(info) == SPI_FLASH_CFI_MFR_ATMEL ||
- (JEDEC_MFR(info) == SPI_FLASH_CFI_MFR_SST) ||
- (JEDEC_MFR(info) == SPI_FLASH_CFI_MFR_MACRONIX)) {
- u8 sr = 0;
-
- if (JEDEC_MFR(info) == SPI_FLASH_CFI_MFR_MACRONIX) {
- read_sr(flash, &sr);
- sr &= STATUS_QEB_MXIC;
- }
- write_sr(flash, sr);
- }
-
- flash->name = info->name;
- flash->memory_map = spi->memory_map;
-
- if (info->flags & SST_WR)
- flash->flags |= SNOR_F_SST_WR;
-
-#ifndef CONFIG_DM_SPI_FLASH
- flash->write = spi_flash_cmd_write_ops;
-#if defined(CONFIG_SPI_FLASH_SST)
- if (flash->flags & SNOR_F_SST_WR) {
- if (spi->mode & SPI_TX_BYTE)
- flash->write = sst_write_bp;
- else
- flash->write = sst_write_wp;
- }
-#endif
- flash->erase = spi_flash_cmd_erase_ops;
- flash->read = spi_flash_cmd_read_ops;
-#endif
-
-#if defined(CONFIG_SPI_FLASH_STMICRO) || defined(CONFIG_SPI_FLASH_SST)
- /* NOR protection support for STmicro/Micron chips and similar */
- if (JEDEC_MFR(info) == SPI_FLASH_CFI_MFR_STMICRO ||
- JEDEC_MFR(info) == SPI_FLASH_CFI_MFR_MICRON ||
- JEDEC_MFR(info) == SPI_FLASH_CFI_MFR_SST) {
- flash->flash_lock = stm_lock;
- flash->flash_unlock = stm_unlock;
- flash->flash_is_locked = stm_is_locked;
- }
-#endif
-
-/* sst26wf series block protection implementation differs from other series */
-#if defined(CONFIG_SPI_FLASH_SST)
- if (JEDEC_MFR(info) == SPI_FLASH_CFI_MFR_SST && info->id[1] == 0x26) {
- flash->flash_lock = sst26_lock;
- flash->flash_unlock = sst26_unlock;
- flash->flash_is_locked = sst26_is_locked;
- }
-#endif
-
- /* Compute the flash size */
- flash->shift = (flash->dual_flash & SF_DUAL_PARALLEL_FLASH) ? 1 : 0;
- flash->page_size = info->page_size;
- /*
- * The Spansion S25FS512S, S25FL032P and S25FL064P have 256b pages,
- * yet use the 0x4d00 Extended JEDEC code. The rest of the Spansion
- * flashes with the 0x4d00 Extended JEDEC code have 512b pages.
- * All of the others have 256b pages.
- */
- if (JEDEC_EXT(info) == 0x4d00) {
- if ((JEDEC_ID(info) != 0x0215) &&
- (JEDEC_ID(info) != 0x0216) &&
- (JEDEC_ID(info) != 0x0220))
- flash->page_size = 512;
- }
- flash->page_size <<= flash->shift;
- flash->sector_size = info->sector_size << flash->shift;
- flash->size = flash->sector_size * info->n_sectors << flash->shift;
-#ifdef CONFIG_SF_DUAL_FLASH
- if (flash->dual_flash & SF_DUAL_STACKED_FLASH)
- flash->size <<= 1;
-#endif
-
-#ifdef CONFIG_SPI_FLASH_USE_4K_SECTORS
- /* Compute erase sector and command */
- if (info->flags & SECT_4K) {
- flash->erase_cmd = CMD_ERASE_4K;
- flash->erase_size = 4096 << flash->shift;
- } else
-#endif
- {
- flash->erase_cmd = CMD_ERASE_64K;
- flash->erase_size = flash->sector_size;
- }
-
- /* Now erase size becomes valid sector size */
- flash->sector_size = flash->erase_size;
-
- /* Look for read commands */
- flash->read_cmd = CMD_READ_ARRAY_FAST;
- if (spi->mode & SPI_RX_SLOW)
- flash->read_cmd = CMD_READ_ARRAY_SLOW;
- else if (spi->mode & SPI_RX_QUAD && info->flags & RD_QUAD)
- flash->read_cmd = CMD_READ_QUAD_OUTPUT_FAST;
- else if (spi->mode & SPI_RX_DUAL && info->flags & RD_DUAL)
- flash->read_cmd = CMD_READ_DUAL_OUTPUT_FAST;
-
- /* Look for write commands */
- if (info->flags & WR_QPP && spi->mode & SPI_TX_QUAD)
- flash->write_cmd = CMD_QUAD_PAGE_PROGRAM;
- else
- /* Go for default supported write cmd */
- flash->write_cmd = CMD_PAGE_PROGRAM;
-
- /* Set the quad enable bit - only for quad commands */
- if ((flash->read_cmd == CMD_READ_QUAD_OUTPUT_FAST) ||
- (flash->read_cmd == CMD_READ_QUAD_IO_FAST) ||
- (flash->write_cmd == CMD_QUAD_PAGE_PROGRAM)) {
- ret = set_quad_mode(flash, info);
- if (ret) {
- debug("SF: Fail to set QEB for %02x\n",
- JEDEC_MFR(info));
- return -EINVAL;
- }
- }
-
- /* Read dummy_byte: dummy byte is determined based on the
- * dummy cycles of a particular command.
- * Fast commands - dummy_byte = dummy_cycles/8
- * I/O commands- dummy_byte = (dummy_cycles * no.of lines)/8
- * For I/O commands except cmd[0] everything goes on no.of lines
- * based on particular command but incase of fast commands except
- * data all go on single line irrespective of command.
- */
- switch (flash->read_cmd) {
- case CMD_READ_QUAD_IO_FAST:
- flash->dummy_byte = 2;
- break;
- case CMD_READ_ARRAY_SLOW:
- flash->dummy_byte = 0;
- break;
- default:
- flash->dummy_byte = 1;
- }
-
-#ifdef CONFIG_SPI_FLASH_STMICRO
- if (info->flags & E_FSR)
- flash->flags |= SNOR_F_USE_FSR;
-#endif
-
- /* Configure the BAR - discover bank cmds and read current bank */
-#ifdef CONFIG_SPI_FLASH_BAR
- ret = read_bar(flash, info);
- if (ret < 0)
- return ret;
-#endif
-
-#if CONFIG_IS_ENABLED(OF_CONTROL) && !CONFIG_IS_ENABLED(OF_PLATDATA)
- ret = spi_flash_decode_fdt(flash);
- if (ret) {
- debug("SF: FDT decode error\n");
- return -EINVAL;
- }
-#endif
-
-#ifndef CONFIG_SPL_BUILD
- printf("SF: Detected %s with page size ", flash->name);
- print_size(flash->page_size, ", erase size ");
- print_size(flash->erase_size, ", total ");
- print_size(flash->size, "");
- if (flash->memory_map)
- printf(", mapped at %p", flash->memory_map);
- puts("\n");
-#endif
-
-#ifndef CONFIG_SPI_FLASH_BAR
- if (((flash->dual_flash == SF_SINGLE_FLASH) &&
- (flash->size > SPI_FLASH_16MB_BOUN)) ||
- ((flash->dual_flash > SF_SINGLE_FLASH) &&
- (flash->size > SPI_FLASH_16MB_BOUN << 1))) {
- puts("SF: Warning - Only lower 16MiB accessible,");
- puts(" Full access #define CONFIG_SPI_FLASH_BAR\n");
- }
-#endif
-
- return 0;
-}
diff --git a/drivers/mtd/spi/spi_flash_ids.c b/drivers/mtd/spi/spi_flash_ids.c
deleted file mode 100644
index ad0a0c815014..000000000000
--- a/drivers/mtd/spi/spi_flash_ids.c
+++ /dev/null
@@ -1,211 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * SPI Flash ID's.
- *
- * Copyright (C) 2016 Jagan Teki <jagan@openedev.com>
- * Copyright (C) 2013 Jagannadha Sutradharudu Teki, Xilinx Inc.
- */
-
-#include <common.h>
-#include <spi.h>
-#include <spi_flash.h>
-
-#include "sf_internal.h"
-
-/* Used when the "_ext_id" is two bytes at most */
-#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
- .id = { \
- ((_jedec_id) >> 16) & 0xff, \
- ((_jedec_id) >> 8) & 0xff, \
- (_jedec_id) & 0xff, \
- ((_ext_id) >> 8) & 0xff, \
- (_ext_id) & 0xff, \
- }, \
- .id_len = (!(_jedec_id) ? 0 : (3 + ((_ext_id) ? 2 : 0))), \
- .sector_size = (_sector_size), \
- .n_sectors = (_n_sectors), \
- .page_size = 256, \
- .flags = (_flags),
-
-#define INFO6(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
- .id = { \
- ((_jedec_id) >> 16) & 0xff, \
- ((_jedec_id) >> 8) & 0xff, \
- (_jedec_id) & 0xff, \
- ((_ext_id) >> 16) & 0xff, \
- ((_ext_id) >> 8) & 0xff, \
- (_ext_id) & 0xff, \
- }, \
- .id_len = 6, \
- .sector_size = (_sector_size), \
- .n_sectors = (_n_sectors), \
- .page_size = 256, \
- .flags = (_flags),
-
-const struct spi_flash_info spi_flash_ids[] = {
-#ifdef CONFIG_SPI_FLASH_ATMEL /* ATMEL */
- {"at45db011d", INFO(0x1f2200, 0x0, 64 * 1024, 4, SECT_4K) },
- {"at45db021d", INFO(0x1f2300, 0x0, 64 * 1024, 8, SECT_4K) },
- {"at45db041d", INFO(0x1f2400, 0x0, 64 * 1024, 8, SECT_4K) },
- {"at45db081d", INFO(0x1f2500, 0x0, 64 * 1024, 16, SECT_4K) },
- {"at45db161d", INFO(0x1f2600, 0x0, 64 * 1024, 32, SECT_4K) },
- {"at45db321d", INFO(0x1f2700, 0x0, 64 * 1024, 64, SECT_4K) },
- {"at45db641d", INFO(0x1f2800, 0x0, 64 * 1024, 128, SECT_4K) },
- {"at25df321a", INFO(0x1f4701, 0x0, 64 * 1024, 64, SECT_4K) },
- {"at25df321", INFO(0x1f4700, 0x0, 64 * 1024, 64, SECT_4K) },
- {"at26df081a", INFO(0x1f4501, 0x0, 64 * 1024, 16, SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_EON /* EON */
- {"en25q32b", INFO(0x1c3016, 0x0, 64 * 1024, 64, 0) },
- {"en25q64", INFO(0x1c3017, 0x0, 64 * 1024, 128, SECT_4K) },
- {"en25q128b", INFO(0x1c3018, 0x0, 64 * 1024, 256, 0) },
- {"en25s64", INFO(0x1c3817, 0x0, 64 * 1024, 128, 0) },
-#endif
-#ifdef CONFIG_SPI_FLASH_GIGADEVICE /* GIGADEVICE */
- {"gd25q16c", INFO(0xc84015, 0x0, 64 * 1024, 32, RD_FULL | WR_QPP | SECT_4K) },
- {"gd25q64b", INFO(0xc84017, 0x0, 64 * 1024, 128, SECT_4K) },
- {"gd25q32b", INFO(0xc84016, 0x0, 64 * 1024, 64, SECT_4K) },
- {"gd25lq32", INFO(0xc86016, 0x0, 64 * 1024, 64, SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_ISSI /* ISSI */
- {"is25lq040b", INFO(0x9d4013, 0x0, 64 * 1024, 8, 0) },
- {"is25lp032", INFO(0x9d6016, 0x0, 64 * 1024, 64, 0) },
- {"is25lp064", INFO(0x9d6017, 0x0, 64 * 1024, 128, 0) },
- {"is25lp128", INFO(0x9d6018, 0x0, 64 * 1024, 256, 0) },
- {"is25lp256", INFO(0x9d6019, 0x0, 64 * 1024, 512, 0) },
- {"is25wp032", INFO(0x9d7016, 0x0, 64 * 1024, 64, RD_FULL | SECT_4K) },
- {"is25wp064", INFO(0x9d7017, 0x0, 64 * 1024, 128, RD_FULL | SECT_4K) },
- {"is25wp128", INFO(0x9d7018, 0x0, 64 * 1024, 256, RD_FULL | SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_MACRONIX /* MACRONIX */
- {"mx25l2006e", INFO(0xc22012, 0x0, 64 * 1024, 4, 0) },
- {"mx25l4005", INFO(0xc22013, 0x0, 64 * 1024, 8, 0) },
- {"mx25l8005", INFO(0xc22014, 0x0, 64 * 1024, 16, 0) },
- {"mx25l1605d", INFO(0xc22015, 0x0, 64 * 1024, 32, 0) },
- {"mx25l3205d", INFO(0xc22016, 0x0, 64 * 1024, 64, 0) },
- {"mx25l6405d", INFO(0xc22017, 0x0, 64 * 1024, 128, 0) },
- {"mx25l12805", INFO(0xc22018, 0x0, 64 * 1024, 256, RD_FULL | WR_QPP) },
- {"mx25l25635f", INFO(0xc22019, 0x0, 64 * 1024, 512, RD_FULL | WR_QPP) },
- {"mx25l51235f", INFO(0xc2201a, 0x0, 64 * 1024, 1024, RD_FULL | WR_QPP) },
- {"mx25l1633e", INFO(0xc22415, 0x0, 64 * 1024, 32, RD_FULL | WR_QPP | SECT_4K) },
- {"mx25u6435f", INFO(0xc22537, 0x0, 64 * 1024, 128, RD_FULL | WR_QPP) },
- {"mx25l12855e", INFO(0xc22618, 0x0, 64 * 1024, 256, RD_FULL | WR_QPP) },
- {"mx25u1635e", INFO(0xc22535, 0x0, 64 * 1024, 32, SECT_4K) },
- {"mx25u25635f", INFO(0xc22539, 0x0, 64 * 1024, 512, RD_FULL | WR_QPP) },
- {"mx66u51235f", INFO(0xc2253a, 0x0, 64 * 1024, 1024, RD_FULL | WR_QPP) },
- {"mx66l1g45g", INFO(0xc2201b, 0x0, 64 * 1024, 2048, RD_FULL | WR_QPP) },
-#endif
-#ifdef CONFIG_SPI_FLASH_SPANSION /* SPANSION */
- {"s25fl008a", INFO(0x010213, 0x0, 64 * 1024, 16, 0) },
- {"s25fl016a", INFO(0x010214, 0x0, 64 * 1024, 32, 0) },
- {"s25fl032a", INFO(0x010215, 0x0, 64 * 1024, 64, 0) },
- {"s25fl064a", INFO(0x010216, 0x0, 64 * 1024, 128, 0) },
- {"s25fl208k", INFO(0x014014, 0x0, 64 * 1024, 16, 0) },
- {"s25fl116k", INFO(0x014015, 0x0, 64 * 1024, 32, 0) },
- {"s25fl164k", INFO(0x014017, 0x0140, 64 * 1024, 128, 0) },
- {"s25fl128p_256k", INFO(0x012018, 0x0300, 256 * 1024, 64, RD_FULL | WR_QPP) },
- {"s25fl128p_64k", INFO(0x012018, 0x0301, 64 * 1024, 256, RD_FULL | WR_QPP) },
- {"s25fl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, RD_FULL | WR_QPP) },
- {"s25fl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, RD_FULL | WR_QPP) },
- {"s25fl128s_256k", INFO(0x012018, 0x4d00, 256 * 1024, 64, RD_FULL | WR_QPP) },
- {"s25fl128s_64k", INFO(0x012018, 0x4d01, 64 * 1024, 256, RD_FULL | WR_QPP) },
- {"s25fl128l", INFO(0x016018, 0, 64 * 1024, 256, RD_FULL | WR_QPP) },
- {"s25fl256s_256k", INFO(0x010219, 0x4d00, 256 * 1024, 128, RD_FULL | WR_QPP) },
- {"s25fs256s_64k", INFO6(0x010219, 0x4d0181, 64 * 1024, 512, RD_FULL | WR_QPP | SECT_4K) },
- {"s25fl256s_64k", INFO(0x010219, 0x4d01, 64 * 1024, 512, RD_FULL | WR_QPP) },
- {"s25fs512s", INFO6(0x010220, 0x4d0081, 256 * 1024, 256, RD_FULL | WR_QPP | SECT_4K) },
- {"s25fl512s_256k", INFO(0x010220, 0x4d00, 256 * 1024, 256, RD_FULL | WR_QPP) },
- {"s25fl512s_64k", INFO(0x010220, 0x4d01, 64 * 1024, 1024, RD_FULL | WR_QPP) },
- {"s25fl512s_512k", INFO(0x010220, 0x4f00, 256 * 1024, 256, RD_FULL | WR_QPP) },
-#endif
-#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
- {"m25p10", INFO(0x202011, 0x0, 32 * 1024, 4, 0) },
- {"m25p20", INFO(0x202012, 0x0, 64 * 1024, 4, 0) },
- {"m25p40", INFO(0x202013, 0x0, 64 * 1024, 8, 0) },
- {"m25p80", INFO(0x202014, 0x0, 64 * 1024, 16, 0) },
- {"m25p16", INFO(0x202015, 0x0, 64 * 1024, 32, 0) },
- {"m25pE16", INFO(0x208015, 0x1000, 64 * 1024, 32, 0) },
- {"m25pX16", INFO(0x207115, 0x1000, 64 * 1024, 32, RD_QUAD | RD_DUAL) },
- {"m25p32", INFO(0x202016, 0x0, 64 * 1024, 64, 0) },
- {"m25p64", INFO(0x202017, 0x0, 64 * 1024, 128, 0) },
- {"m25p128", INFO(0x202018, 0x0, 256 * 1024, 64, 0) },
- {"m25pX64", INFO(0x207117, 0x0, 64 * 1024, 128, SECT_4K) },
- {"n25q016a", INFO(0x20bb15, 0x0, 64 * 1024, 32, SECT_4K) },
- {"n25q32", INFO(0x20ba16, 0x0, 64 * 1024, 64, RD_FULL | WR_QPP | SECT_4K) },
- {"n25q32a", INFO(0x20bb16, 0x0, 64 * 1024, 64, RD_FULL | WR_QPP | SECT_4K) },
- {"n25q64", INFO(0x20ba17, 0x0, 64 * 1024, 128, RD_FULL | WR_QPP | SECT_4K) },
- {"n25q64a", INFO(0x20bb17, 0x0, 64 * 1024, 128, RD_FULL | WR_QPP | SECT_4K) },
- {"n25q128", INFO(0x20ba18, 0x0, 64 * 1024, 256, RD_FULL | WR_QPP) },
- {"n25q128a", INFO(0x20bb18, 0x0, 64 * 1024, 256, RD_FULL | WR_QPP) },
- {"n25q256", INFO(0x20ba19, 0x0, 64 * 1024, 512, RD_FULL | WR_QPP | E_FSR | SECT_4K) },
- {"n25q256a", INFO(0x20bb19, 0x0, 64 * 1024, 512, RD_FULL | WR_QPP | E_FSR | SECT_4K) },
- {"n25q512", INFO(0x20ba20, 0x0, 64 * 1024, 1024, RD_FULL | WR_QPP | E_FSR | SECT_4K) },
- {"n25q512a", INFO(0x20bb20, 0x0, 64 * 1024, 1024, RD_FULL | WR_QPP | E_FSR | SECT_4K) },
- {"n25q1024", INFO(0x20ba21, 0x0, 64 * 1024, 2048, RD_FULL | WR_QPP | E_FSR | SECT_4K) },
- {"n25q1024a", INFO(0x20bb21, 0x0, 64 * 1024, 2048, RD_FULL | WR_QPP | E_FSR | SECT_4K) },
- {"mt25qu02g", INFO(0x20bb22, 0x0, 64 * 1024, 4096, RD_FULL | WR_QPP | E_FSR | SECT_4K) },
- {"mt25ql02g", INFO(0x20ba22, 0x0, 64 * 1024, 4096, RD_FULL | WR_QPP | E_FSR | SECT_4K) },
- {"mt35xu512g", INFO6(0x2c5b1a, 0x104100, 128 * 1024, 512, E_FSR | SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_SST /* SST */
- {"sst25vf040b", INFO(0xbf258d, 0x0, 64 * 1024, 8, SECT_4K | SST_WR) },
- {"sst25vf080b", INFO(0xbf258e, 0x0, 64 * 1024, 16, SECT_4K | SST_WR) },
- {"sst25vf016b", INFO(0xbf2541, 0x0, 64 * 1024, 32, SECT_4K | SST_WR) },
- {"sst25vf032b", INFO(0xbf254a, 0x0, 64 * 1024, 64, SECT_4K | SST_WR) },
- {"sst25vf064c", INFO(0xbf254b, 0x0, 64 * 1024, 128, SECT_4K) },
- {"sst25wf512", INFO(0xbf2501, 0x0, 64 * 1024, 1, SECT_4K | SST_WR) },
- {"sst25wf010", INFO(0xbf2502, 0x0, 64 * 1024, 2, SECT_4K | SST_WR) },
- {"sst25wf020", INFO(0xbf2503, 0x0, 64 * 1024, 4, SECT_4K | SST_WR) },
- {"sst25wf040", INFO(0xbf2504, 0x0, 64 * 1024, 8, SECT_4K | SST_WR) },
- {"sst25wf040b", INFO(0x621613, 0x0, 64 * 1024, 8, SECT_4K) },
- {"sst25wf080", INFO(0xbf2505, 0x0, 64 * 1024, 16, SECT_4K | SST_WR) },
- {"sst26wf016", INFO(0xbf2651, 0x0, 64 * 1024, 32, SECT_4K) },
- {"sst26wf032", INFO(0xbf2622, 0x0, 64 * 1024, 64, SECT_4K) },
- {"sst26wf064", INFO(0xbf2643, 0x0, 64 * 1024, 128, SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_WINBOND /* WINBOND */
- {"w25p80", INFO(0xef2014, 0x0, 64 * 1024, 16, 0) },
- {"w25p16", INFO(0xef2015, 0x0, 64 * 1024, 32, 0) },
- {"w25p32", INFO(0xef2016, 0x0, 64 * 1024, 64, 0) },
- {"w25x40", INFO(0xef3013, 0x0, 64 * 1024, 8, SECT_4K) },
- {"w25x16", INFO(0xef3015, 0x0, 64 * 1024, 32, SECT_4K) },
- {"w25x32", INFO(0xef3016, 0x0, 64 * 1024, 64, SECT_4K) },
- {"w25x64", INFO(0xef3017, 0x0, 64 * 1024, 128, SECT_4K) },
- {"w25q80bl", INFO(0xef4014, 0x0, 64 * 1024, 16, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q16cl", INFO(0xef4015, 0x0, 64 * 1024, 32, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q32bv", INFO(0xef4016, 0x0, 64 * 1024, 64, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q64cv", INFO(0xef4017, 0x0, 64 * 1024, 128, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q128bv", INFO(0xef4018, 0x0, 64 * 1024, 256, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q256", INFO(0xef4019, 0x0, 64 * 1024, 512, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q80bw", INFO(0xef5014, 0x0, 64 * 1024, 16, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q16dw", INFO(0xef6015, 0x0, 64 * 1024, 32, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q16jv", INFO(0xef7015, 0x0, 64 * 1024, 32, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q32dw", INFO(0xef6016, 0x0, 64 * 1024, 64, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q32jv", INFO(0xef7016, 0x0, 64 * 1024, 64, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q64dw", INFO(0xef6017, 0x0, 64 * 1024, 128, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q64jv", INFO(0xef7017, 0x0, 64 * 1024, 128, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q128fw", INFO(0xef6018, 0x0, 64 * 1024, 256, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q128jv", INFO(0xef7018, 0x0, 64 * 1024, 256, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q256fw", INFO(0xef6019, 0x0, 64 * 1024, 512, RD_FULL | WR_QPP | SECT_4K) },
- {"w25q256jw", INFO(0xef7019, 0x0, 64 * 1024, 512, RD_FULL | WR_QPP | SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_XMC /* Wuhan Xinxin Semiconductor Manufacturing Corp */
- { "xm25qh64a", INFO(0x207017, 0x0, 64 * 1024, 128, SECT_4K | RD_DUAL | RD_QUAD) },
- { "xm25qh128a", INFO(0x207018, 0x0, 64 * 1024, 256, SECT_4K | RD_DUAL | RD_QUAD) },
-#endif
- {}, /* Empty entry to terminate the list */
- /*
- * Note:
- * Below paired flash devices has similar spi_flash params.
- * (s25fl129p_64k, s25fl128s_64k)
- * (w25q80bl, w25q80bv)
- * (w25q16cl, w25q16dv, w25q16jv)
- * (w25q32bv, w25q32fv_spi)
- * (w25q64cv, w25q64fv_spi)
- * (w25q128bv, w25q128fv_spi)
- * (w25q32dw, w25q32fv_qpi)
- * (w25q64dw, w25q64fv_qpi)
- * (w25q128fw, w25q128fv_qpi)
- * (w25q256fw, w25q256fv_qpi)
- */
-};
--
2.20.1
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 07/11] mtd: spi: Add lightweight SPI flash stack for SPL
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (5 preceding siblings ...)
2018-12-21 6:38 ` [U-Boot] [PATCH v2 06/11] mtd: spi: Remove unused files Vignesh R
@ 2018-12-21 6:38 ` Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 08/11] configs: Enable SPI_FLASH_TINY for resource constrained boards Vignesh R
` (7 subsequent siblings)
14 siblings, 0 replies; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
Add a tiny SPI flash stack that just supports reading data/images from
SPI flash. This is useful for boards that have SPL size constraints and
would need to use SPI flash framework just to read images/data from
flash. There is approximately 1.5 to 2KB savings with this.
Based on prior work of reducing spi flash id table by
Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
common/spl/Kconfig | 10 +-
drivers/mtd/spi/Makefile | 10 +-
drivers/mtd/spi/sf_internal.h | 2 +
drivers/mtd/spi/spi-nor-core.c | 266 +----------
drivers/mtd/spi/spi-nor-ids.c | 297 ++++++++++++
drivers/mtd/spi/spi-nor-tiny.c | 810 +++++++++++++++++++++++++++++++++
6 files changed, 1131 insertions(+), 264 deletions(-)
create mode 100644 drivers/mtd/spi/spi-nor-ids.c
create mode 100644 drivers/mtd/spi/spi-nor-tiny.c
diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index 9d8405b7daa8..f5f3ac3cf290 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -731,9 +731,17 @@ config SPL_SPI_FLASH_SUPPORT
if SPL_SPI_FLASH_SUPPORT
+config SPL_SPI_FLASH_TINY
+ bool "Enable low footprint SPL SPI Flash support"
+ help
+ Enable lightweight SPL SPI Flash support that supports just reading
+ data/images from flash. No support to write/erase flash. Enable
+ this if you have SPL size limitations and don't need full
+ fledged SPI flash support.
+
config SPL_SPI_FLASH_SFDP_SUPPORT
bool "SFDP table parsing support for SPI NOR flashes"
- depends on !SPI_FLASH_BAR
+ depends on !SPI_FLASH_BAR && !SPL_SPI_FLASH_TINY
help
Enable support for parsing and auto discovery of parameters for
SPI NOR flashes using Serial Flash Discoverable Parameters (SFDP)
diff --git a/drivers/mtd/spi/Makefile b/drivers/mtd/spi/Makefile
index 70058d3df2b9..f99f6cb16e29 100644
--- a/drivers/mtd/spi/Makefile
+++ b/drivers/mtd/spi/Makefile
@@ -4,12 +4,20 @@
# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
obj-$(CONFIG_DM_SPI_FLASH) += sf-uclass.o
+spi-nor-y := sf_probe.o spi-nor-ids.o
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_SPI_BOOT) += fsl_espi_spl.o
+ifeq ($(CONFIG_SPL_SPI_FLASH_TINY),y)
+spi-nor-y += spi-nor-tiny.o
+else
+spi-nor-y += spi-nor-core.o
+endif
+else
+spi-nor-y += spi-nor-core.o
endif
-obj-$(CONFIG_SPI_FLASH) += sf_probe.o spi-nor-core.o
+obj-$(CONFIG_SPI_FLASH) += spi-nor.o
obj-$(CONFIG_SPI_FLASH_DATAFLASH) += sf_dataflash.o sf.o
obj-$(CONFIG_SPI_FLASH_MTD) += sf_mtd.o
obj-$(CONFIG_SPI_FLASH_SANDBOX) += sandbox.o
diff --git a/drivers/mtd/spi/sf_internal.h b/drivers/mtd/spi/sf_internal.h
index fd00e0d1b23b..a6bf734830a7 100644
--- a/drivers/mtd/spi/sf_internal.h
+++ b/drivers/mtd/spi/sf_internal.h
@@ -16,7 +16,9 @@
#define SPI_NOR_MAX_ADDR_WIDTH 4
struct flash_info {
+#if !CONFIG_IS_ENABLED(SPI_FLASH_TINY)
char *name;
+#endif
/*
* This array stores the ID bytes.
diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c
index c2e5f9320b95..b006bff64684 100644
--- a/drivers/mtd/spi/spi-nor-core.c
+++ b/drivers/mtd/spi/spi-nor-core.c
@@ -881,284 +881,26 @@ static int stm_is_locked(struct spi_nor *nor, loff_t ofs, uint64_t len)
}
#endif /* CONFIG_SPI_FLASH_STMICRO */
-/* Used when the "_ext_id" is two bytes at most */
-#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
- .id = { \
- ((_jedec_id) >> 16) & 0xff, \
- ((_jedec_id) >> 8) & 0xff, \
- (_jedec_id) & 0xff, \
- ((_ext_id) >> 8) & 0xff, \
- (_ext_id) & 0xff, \
- }, \
- .id_len = (!(_jedec_id) ? 0 : (3 + ((_ext_id) ? 2 : 0))), \
- .sector_size = (_sector_size), \
- .n_sectors = (_n_sectors), \
- .page_size = 256, \
- .flags = (_flags),
-
-#define INFO6(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
- .id = { \
- ((_jedec_id) >> 16) & 0xff, \
- ((_jedec_id) >> 8) & 0xff, \
- (_jedec_id) & 0xff, \
- ((_ext_id) >> 16) & 0xff, \
- ((_ext_id) >> 8) & 0xff, \
- (_ext_id) & 0xff, \
- }, \
- .id_len = 6, \
- .sector_size = (_sector_size), \
- .n_sectors = (_n_sectors), \
- .page_size = 256, \
- .flags = (_flags),
-
-/* NOTE: double check command sets and memory organization when you add
- * more nor chips. This current list focusses on newer chips, which
- * have been converging on command sets which including JEDEC ID.
- *
- * All newly added entries should describe *hardware* and should use SECT_4K
- * (or SECT_4K_PMC) if hardware supports erasing 4 KiB sectors. For usage
- * scenarios excluding small sectors there is config option that can be
- * disabled: CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.
- * For historical (and compatibility) reasons (before we got above config) some
- * old entries may be missing 4K flag.
- */
-const struct flash_info spi_nor_ids[] = {
-#ifdef CONFIG_SPI_FLASH_ATMEL /* ATMEL */
- /* Atmel -- some are (confusingly) marketed as "DataFlash" */
- { "at26df321", INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) },
- { "at25df321a", INFO(0x1f4701, 0, 64 * 1024, 64, SECT_4K) },
-
- { "at45db011d", INFO(0x1f2200, 0, 64 * 1024, 4, SECT_4K) },
- { "at45db021d", INFO(0x1f2300, 0, 64 * 1024, 8, SECT_4K) },
- { "at45db041d", INFO(0x1f2400, 0, 64 * 1024, 8, SECT_4K) },
- { "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) },
- { "at45db161d", INFO(0x1f2600, 0, 64 * 1024, 32, SECT_4K) },
- { "at45db321d", INFO(0x1f2700, 0, 64 * 1024, 64, SECT_4K) },
- { "at45db641d", INFO(0x1f2800, 0, 64 * 1024, 128, SECT_4K) },
- { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_EON /* EON */
- /* EON -- en25xxx */
- { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) },
- { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) },
- { "en25qh128", INFO(0x1c7018, 0, 64 * 1024, 256, 0) },
- { "en25s64", INFO(0x1c3817, 0, 64 * 1024, 128, SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_GIGADEVICE /* GIGADEVICE */
- /* GigaDevice */
- {
- "gd25q16", INFO(0xc84015, 0, 64 * 1024, 32,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
- "gd25q32", INFO(0xc84016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
- "gd25lq32", INFO(0xc86016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
- "gd25q64", INFO(0xc84017, 0, 64 * 1024, 128,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
-#endif
-#ifdef CONFIG_SPI_FLASH_ISSI /* ISSI */
- /* ISSI */
- { "is25lq040b", INFO(0x9d4013, 0, 64 * 1024, 8,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "is25lp032", INFO(0x9d6016, 0, 64 * 1024, 64, 0) },
- { "is25lp064", INFO(0x9d6017, 0, 64 * 1024, 128, 0) },
- { "is25lp128", INFO(0x9d6018, 0, 64 * 1024, 256,
- SECT_4K | SPI_NOR_DUAL_READ) },
- { "is25lp256", INFO(0x9d6019, 0, 64 * 1024, 512,
- SECT_4K | SPI_NOR_DUAL_READ) },
- { "is25wp032", INFO(0x9d7016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "is25wp064", INFO(0x9d7017, 0, 64 * 1024, 128,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "is25wp128", INFO(0x9d7018, 0, 64 * 1024, 256,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-#endif
-#ifdef CONFIG_SPI_FLASH_MACRONIX /* MACRONIX */
- /* Macronix */
- { "mx25l2005a", INFO(0xc22012, 0, 64 * 1024, 4, SECT_4K) },
- { "mx25l4005a", INFO(0xc22013, 0, 64 * 1024, 8, SECT_4K) },
- { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) },
- { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) },
- { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, SECT_4K) },
- { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, SECT_4K) },
- { "mx25u2033e", INFO(0xc22532, 0, 64 * 1024, 4, SECT_4K) },
- { "mx25u1635e", INFO(0xc22535, 0, 64 * 1024, 32, SECT_4K) },
- { "mx25u6435f", INFO(0xc22537, 0, 64 * 1024, 128, SECT_4K) },
- { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
- { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
- { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "mx25u25635f", INFO(0xc22539, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_4B_OPCODES) },
- { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
- { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
- { "mx66u51235f", INFO(0xc2253a, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
- { "mx66l1g45g", INFO(0xc2201b, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "mx25l1633e", INFO(0xc22415, 0, 64 * 1024, 32, SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES | SECT_4K) },
-#endif
-
-#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
- /* Micron */
- { "n25q016a", INFO(0x20bb15, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
- { "n25q032a", INFO(0x20bb16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
- { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q064a", INFO(0x20bb17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "n25q256ax1", INFO(0x20bb19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
- { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
- { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
- { "n25q00a", INFO(0x20bb21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
- { "mt25qu02g", INFO(0x20bb22, 0, 64 * 1024, 4096, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
-#endif
-#ifdef CONFIG_SPI_FLASH_SPANSION /* SPANSION */
- /* Spansion/Cypress -- single (large) sector size only, at least
- * for the chips listed here (without boot sectors).
- */
- { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR) },
- { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl512s", INFO6(0x010220, 0x4d0081, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl512s_256k", INFO(0x010220, 0x4d00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl512s_64k", INFO(0x010220, 0x4d01, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl512s_512k", INFO(0x010220, 0x4f00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
- { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
- { "s25fl128s", INFO6(0x012018, 0x4d0180, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
- { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
- { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) },
- { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) },
- { "s25fl116k", INFO(0x014015, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "s25fl164k", INFO(0x014017, 0, 64 * 1024, 128, SECT_4K) },
- { "s25fl208k", INFO(0x014014, 0, 64 * 1024, 16, SECT_4K | SPI_NOR_DUAL_READ) },
- { "s25fl128l", INFO(0x016018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
-#endif
-#ifdef CONFIG_SPI_FLASH_SST /* SST */
- /* SST -- large erase sizes are "overlays", "sectors" are 4K */
- { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
- { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
- { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K | SST_WRITE) },
- { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K | SST_WRITE) },
- { "sst25vf064c", INFO(0xbf254b, 0, 64 * 1024, 128, SECT_4K) },
- { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1, SECT_4K | SST_WRITE) },
- { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2, SECT_4K | SST_WRITE) },
- { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4, SECT_4K | SST_WRITE) },
- { "sst25wf020a", INFO(0x621612, 0, 64 * 1024, 4, SECT_4K) },
- { "sst25wf040b", INFO(0x621613, 0, 64 * 1024, 8, SECT_4K) },
- { "sst25wf040", INFO(0xbf2504, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
- { "sst25wf080", INFO(0xbf2505, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
- { "sst26vf064b", INFO(0xbf2643, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "sst26wf016", INFO(0xbf2651, 0, 64 * 1024, 32, SECT_4K) },
- { "sst26wf032", INFO(0xbf2622, 0, 64 * 1024, 64, SECT_4K) },
- { "sst26wf064", INFO(0xbf2643, 0, 64 * 1024, 128, SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
- /* ST Microelectronics -- newer production may have feature updates */
- { "m25p10", INFO(0x202011, 0, 32 * 1024, 4, 0) },
- { "m25p20", INFO(0x202012, 0, 64 * 1024, 4, 0) },
- { "m25p40", INFO(0x202013, 0, 64 * 1024, 8, 0) },
- { "m25p80", INFO(0x202014, 0, 64 * 1024, 16, 0) },
- { "m25p16", INFO(0x202015, 0, 64 * 1024, 32, 0) },
- { "m25p32", INFO(0x202016, 0, 64 * 1024, 64, 0) },
- { "m25p64", INFO(0x202017, 0, 64 * 1024, 128, 0) },
- { "m25p128", INFO(0x202018, 0, 256 * 1024, 64, 0) },
- { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) },
- { "m25px16", INFO(0x207115, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "m25px64", INFO(0x207117, 0, 64 * 1024, 128, 0) },
-#endif
-#ifdef CONFIG_SPI_FLASH_WINBOND /* WINBOND */
- /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
- { "w25x05", INFO(0xef3010, 0, 64 * 1024, 1, SECT_4K) },
- { "w25x10", INFO(0xef3011, 0, 64 * 1024, 2, SECT_4K) },
- { "w25x20", INFO(0xef3012, 0, 64 * 1024, 4, SECT_4K) },
- { "w25x40", INFO(0xef3013, 0, 64 * 1024, 8, SECT_4K) },
- { "w25x80", INFO(0xef3014, 0, 64 * 1024, 16, SECT_4K) },
- { "w25x16", INFO(0xef3015, 0, 64 * 1024, 32, SECT_4K) },
- {
- "w25q16dw", INFO(0xef6015, 0, 64 * 1024, 32,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- { "w25x32", INFO(0xef3016, 0, 64 * 1024, 64, SECT_4K) },
- { "w25q20cl", INFO(0xef4012, 0, 64 * 1024, 4, SECT_4K) },
- { "w25q20bw", INFO(0xef5012, 0, 64 * 1024, 4, SECT_4K) },
- { "w25q20ew", INFO(0xef6012, 0, 64 * 1024, 4, SECT_4K) },
- { "w25q32", INFO(0xef4016, 0, 64 * 1024, 64, SECT_4K) },
- {
- "w25q32dw", INFO(0xef6016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
- "w25q32jv", INFO(0xef7016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
- { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
- {
- "w25q64dw", INFO(0xef6017, 0, 64 * 1024, 128,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
- "w25q128fw", INFO(0xef6018, 0, 64 * 1024, 256,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) },
- { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) },
- { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) },
- { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024,
- SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ) },
-#endif
-#ifdef CONFIG_SPI_FLASH_XMC
- /* XMC (Wuhan Xinxin Semiconductor Manufacturing Corp.) */
- { "XM25QH64A", INFO(0x207017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "XM25QH128A", INFO(0x207018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-#endif
- { },
-};
-
static const struct flash_info *spi_nor_read_id(struct spi_nor *nor)
{
int tmp;
u8 id[SPI_NOR_MAX_ID_LEN];
const struct flash_info *info;
- if (!ARRAY_SIZE(spi_nor_ids))
- return ERR_PTR(-ENODEV);
-
tmp = nor->read_reg(nor, SPINOR_OP_RDID, id, SPI_NOR_MAX_ID_LEN);
if (tmp < 0) {
dev_dbg(nor->dev, "error %d reading JEDEC ID\n", tmp);
return ERR_PTR(tmp);
}
- for (tmp = 0; tmp < ARRAY_SIZE(spi_nor_ids) - 1; tmp++) {
- info = &spi_nor_ids[tmp];
+ info = spi_nor_ids;
+ for (; info->name; info++) {
if (info->id_len) {
if (!memcmp(info->id, id, info->id_len))
- return &spi_nor_ids[tmp];
+ return info;
}
}
+
dev_err(nor->dev, "unrecognized JEDEC id bytes: %02x, %02x, %02x\n",
id[0], id[1], id[2]);
return ERR_PTR(-ENODEV);
diff --git a/drivers/mtd/spi/spi-nor-ids.c b/drivers/mtd/spi/spi-nor-ids.c
new file mode 100644
index 000000000000..3215e2431dc0
--- /dev/null
+++ b/drivers/mtd/spi/spi-nor-ids.c
@@ -0,0 +1,297 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ *
+ * Copyright (C) 2013 Jagannadha Sutradharudu Teki, Xilinx Inc.
+ * Copyright (C) 2016 Jagan Teki <jagan@openedev.com>
+ * Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+#include <common.h>
+#include <spi.h>
+#include <spi_flash.h>
+
+#include "sf_internal.h"
+
+/* Exclude chip names for SPL to save space */
+#if !CONFIG_IS_ENABLED(SPI_FLASH_TINY)
+#define INFO_NAME(_name) .name = _name,
+#else
+#define INFO_NAME(_name)
+#endif
+
+/* Used when the "_ext_id" is two bytes at most */
+#define INFO(_name, _jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
+ INFO_NAME(_name) \
+ .id = { \
+ ((_jedec_id) >> 16) & 0xff, \
+ ((_jedec_id) >> 8) & 0xff, \
+ (_jedec_id) & 0xff, \
+ ((_ext_id) >> 8) & 0xff, \
+ (_ext_id) & 0xff, \
+ }, \
+ .id_len = (!(_jedec_id) ? 0 : (3 + ((_ext_id) ? 2 : 0))), \
+ .sector_size = (_sector_size), \
+ .n_sectors = (_n_sectors), \
+ .page_size = 256, \
+ .flags = (_flags),
+
+#define INFO6(_name, _jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
+ INFO_NAME(_name) \
+ .id = { \
+ ((_jedec_id) >> 16) & 0xff, \
+ ((_jedec_id) >> 8) & 0xff, \
+ (_jedec_id) & 0xff, \
+ ((_ext_id) >> 16) & 0xff, \
+ ((_ext_id) >> 8) & 0xff, \
+ (_ext_id) & 0xff, \
+ }, \
+ .id_len = 6, \
+ .sector_size = (_sector_size), \
+ .n_sectors = (_n_sectors), \
+ .page_size = 256, \
+ .flags = (_flags),
+
+/* NOTE: double check command sets and memory organization when you add
+ * more nor chips. This current list focusses on newer chips, which
+ * have been converging on command sets which including JEDEC ID.
+ *
+ * All newly added entries should describe *hardware* and should use SECT_4K
+ * (or SECT_4K_PMC) if hardware supports erasing 4 KiB sectors. For usage
+ * scenarios excluding small sectors there is config option that can be
+ * disabled: CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.
+ * For historical (and compatibility) reasons (before we got above config) some
+ * old entries may be missing 4K flag.
+ */
+const struct flash_info spi_nor_ids[] = {
+#ifdef CONFIG_SPI_FLASH_ATMEL /* ATMEL */
+ /* Atmel -- some are (confusingly) marketed as "DataFlash" */
+ { INFO("at26df321", 0x1f4700, 0, 64 * 1024, 64, SECT_4K) },
+ { INFO("at25df321a", 0x1f4701, 0, 64 * 1024, 64, SECT_4K) },
+
+ { INFO("at45db011d", 0x1f2200, 0, 64 * 1024, 4, SECT_4K) },
+ { INFO("at45db021d", 0x1f2300, 0, 64 * 1024, 8, SECT_4K) },
+ { INFO("at45db041d", 0x1f2400, 0, 64 * 1024, 8, SECT_4K) },
+ { INFO("at45db081d", 0x1f2500, 0, 64 * 1024, 16, SECT_4K) },
+ { INFO("at45db161d", 0x1f2600, 0, 64 * 1024, 32, SECT_4K) },
+ { INFO("at45db321d", 0x1f2700, 0, 64 * 1024, 64, SECT_4K) },
+ { INFO("at45db641d", 0x1f2800, 0, 64 * 1024, 128, SECT_4K) },
+ { INFO("at26df081a", 0x1f4501, 0, 64 * 1024, 16, SECT_4K) },
+#endif
+#ifdef CONFIG_SPI_FLASH_EON /* EON */
+ /* EON -- en25xxx */
+ { INFO("en25q32b", 0x1c3016, 0, 64 * 1024, 64, 0) },
+ { INFO("en25q64", 0x1c3017, 0, 64 * 1024, 128, SECT_4K) },
+ { INFO("en25qh128", 0x1c7018, 0, 64 * 1024, 256, 0) },
+ { INFO("en25s64", 0x1c3817, 0, 64 * 1024, 128, SECT_4K) },
+#endif
+#ifdef CONFIG_SPI_FLASH_GIGADEVICE /* GIGADEVICE */
+ /* GigaDevice */
+ {
+ INFO("gd25q16", 0xc84015, 0, 64 * 1024, 32,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ INFO("gd25q32", 0xc84016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ INFO("gd25lq32", 0xc86016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ INFO("gd25q64", 0xc84017, 0, 64 * 1024, 128,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+#endif
+#ifdef CONFIG_SPI_FLASH_ISSI /* ISSI */
+ /* ISSI */
+ { INFO("is25lq040b", 0x9d4013, 0, 64 * 1024, 8,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("is25lp032", 0x9d6016, 0, 64 * 1024, 64, 0) },
+ { INFO("is25lp064", 0x9d6017, 0, 64 * 1024, 128, 0) },
+ { INFO("is25lp128", 0x9d6018, 0, 64 * 1024, 256,
+ SECT_4K | SPI_NOR_DUAL_READ) },
+ { INFO("is25lp256", 0x9d6019, 0, 64 * 1024, 512,
+ SECT_4K | SPI_NOR_DUAL_READ) },
+ { INFO("is25wp032", 0x9d7016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("is25wp064", 0x9d7017, 0, 64 * 1024, 128,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("is25wp128", 0x9d7018, 0, 64 * 1024, 256,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+#endif
+#ifdef CONFIG_SPI_FLASH_MACRONIX /* MACRONIX */
+ /* Macronix */
+ { INFO("mx25l2005a", 0xc22012, 0, 64 * 1024, 4, SECT_4K) },
+ { INFO("mx25l4005a", 0xc22013, 0, 64 * 1024, 8, SECT_4K) },
+ { INFO("mx25l8005", 0xc22014, 0, 64 * 1024, 16, 0) },
+ { INFO("mx25l1606e", 0xc22015, 0, 64 * 1024, 32, SECT_4K) },
+ { INFO("mx25l3205d", 0xc22016, 0, 64 * 1024, 64, SECT_4K) },
+ { INFO("mx25l6405d", 0xc22017, 0, 64 * 1024, 128, SECT_4K) },
+ { INFO("mx25u2033e", 0xc22532, 0, 64 * 1024, 4, SECT_4K) },
+ { INFO("mx25u1635e", 0xc22535, 0, 64 * 1024, 32, SECT_4K) },
+ { INFO("mx25u6435f", 0xc22537, 0, 64 * 1024, 128, SECT_4K) },
+ { INFO("mx25l12805d", 0xc22018, 0, 64 * 1024, 256, 0) },
+ { INFO("mx25l12855e", 0xc22618, 0, 64 * 1024, 256, 0) },
+ { INFO("mx25l25635e", 0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("mx25u25635f", 0xc22539, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_4B_OPCODES) },
+ { INFO("mx25l25655e", 0xc22619, 0, 64 * 1024, 512, 0) },
+ { INFO("mx66l51235l", 0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+ { INFO("mx66u51235f", 0xc2253a, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+ { INFO("mx66l1g45g", 0xc2201b, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("mx25l1633e", 0xc22415, 0, 64 * 1024, 32, SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES | SECT_4K) },
+#endif
+
+#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
+ /* Micron */
+ { INFO("n25q016a", 0x20bb15, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_QUAD_READ) },
+ { INFO("n25q032", 0x20ba16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
+ { INFO("n25q032a", 0x20bb16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
+ { INFO("n25q064", 0x20ba17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
+ { INFO("n25q064a", 0x20bb17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
+ { INFO("n25q128a11", 0x20bb18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
+ { INFO("n25q128a13", 0x20ba18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
+ { INFO("n25q256a", 0x20ba19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+ { INFO("n25q256ax1", 0x20bb19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+ { INFO("n25q512a", 0x20bb20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+ { INFO("n25q512ax3", 0x20ba20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+ { INFO("n25q00", 0x20ba21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
+ { INFO("n25q00a", 0x20bb21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
+ { INFO("mt25qu02g", 0x20bb22, 0, 64 * 1024, 4096, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
+#endif
+#ifdef CONFIG_SPI_FLASH_SPANSION /* SPANSION */
+ /* Spansion/Cypress -- single (large) sector size only, at least
+ * for the chips listed here (without boot sectors).
+ */
+ { INFO("s25sl032p", 0x010215, 0x4d00, 64 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("s25sl064p", 0x010216, 0x4d00, 64 * 1024, 128, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("s25fl256s0", 0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR) },
+ { INFO("s25fl256s1", 0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { INFO6("s25fl512s", 0x010220, 0x4d0081, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { INFO("s25fl512s_256k", 0x010220, 0x4d00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { INFO("s25fl512s_64k", 0x010220, 0x4d01, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { INFO("s25fl512s_512k", 0x010220, 0x4f00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { INFO("s25sl12800", 0x012018, 0x0300, 256 * 1024, 64, 0) },
+ { INFO("s25sl12801", 0x012018, 0x0301, 64 * 1024, 256, 0) },
+ { INFO6("s25fl128s", 0x012018, 0x4d0180, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { INFO("s25fl129p0", 0x012018, 0x4d00, 256 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { INFO("s25fl129p1", 0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { INFO("s25sl008a", 0x010213, 0, 64 * 1024, 16, 0) },
+ { INFO("s25sl016a", 0x010214, 0, 64 * 1024, 32, 0) },
+ { INFO("s25sl032a", 0x010215, 0, 64 * 1024, 64, 0) },
+ { INFO("s25sl064a", 0x010216, 0, 64 * 1024, 128, 0) },
+ { INFO("s25fl116k", 0x014015, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("s25fl164k", 0x014017, 0, 64 * 1024, 128, SECT_4K) },
+ { INFO("s25fl208k", 0x014014, 0, 64 * 1024, 16, SECT_4K | SPI_NOR_DUAL_READ) },
+ { INFO("s25fl128l", 0x016018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+#endif
+#ifdef CONFIG_SPI_FLASH_SST /* SST */
+ /* SST -- large erase sizes are "overlays", "sectors" are 4K */
+ { INFO("sst25vf040b", 0xbf258d, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
+ { INFO("sst25vf080b", 0xbf258e, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
+ { INFO("sst25vf016b", 0xbf2541, 0, 64 * 1024, 32, SECT_4K | SST_WRITE) },
+ { INFO("sst25vf032b", 0xbf254a, 0, 64 * 1024, 64, SECT_4K | SST_WRITE) },
+ { INFO("sst25vf064c", 0xbf254b, 0, 64 * 1024, 128, SECT_4K) },
+ { INFO("sst25wf512", 0xbf2501, 0, 64 * 1024, 1, SECT_4K | SST_WRITE) },
+ { INFO("sst25wf010", 0xbf2502, 0, 64 * 1024, 2, SECT_4K | SST_WRITE) },
+ { INFO("sst25wf020", 0xbf2503, 0, 64 * 1024, 4, SECT_4K | SST_WRITE) },
+ { INFO("sst25wf020a", 0x621612, 0, 64 * 1024, 4, SECT_4K) },
+ { INFO("sst25wf040b", 0x621613, 0, 64 * 1024, 8, SECT_4K) },
+ { INFO("sst25wf040", 0xbf2504, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
+ { INFO("sst25wf080", 0xbf2505, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
+ { INFO("sst26vf064b", 0xbf2643, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("sst26wf016", 0xbf2651, 0, 64 * 1024, 32, SECT_4K) },
+ { INFO("sst26wf032", 0xbf2622, 0, 64 * 1024, 64, SECT_4K) },
+ { INFO("sst26wf064", 0xbf2643, 0, 64 * 1024, 128, SECT_4K) },
+#endif
+#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
+ /* ST Microelectronics -- newer production may have feature updates */
+ { INFO("m25p10", 0x202011, 0, 32 * 1024, 4, 0) },
+ { INFO("m25p20", 0x202012, 0, 64 * 1024, 4, 0) },
+ { INFO("m25p40", 0x202013, 0, 64 * 1024, 8, 0) },
+ { INFO("m25p80", 0x202014, 0, 64 * 1024, 16, 0) },
+ { INFO("m25p16", 0x202015, 0, 64 * 1024, 32, 0) },
+ { INFO("m25p32", 0x202016, 0, 64 * 1024, 64, 0) },
+ { INFO("m25p64", 0x202017, 0, 64 * 1024, 128, 0) },
+ { INFO("m25p128", 0x202018, 0, 256 * 1024, 64, 0) },
+ { INFO("m25pe16", 0x208015, 0, 64 * 1024, 32, SECT_4K) },
+ { INFO("m25px16", 0x207115, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("m25px64", 0x207117, 0, 64 * 1024, 128, 0) },
+#endif
+#ifdef CONFIG_SPI_FLASH_WINBOND /* WINBOND */
+ /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
+ { INFO("w25p80", 0xef2014, 0x0, 64 * 1024, 16, 0) },
+ { INFO("w25p16", 0xef2015, 0x0, 64 * 1024, 32, 0) },
+ { INFO("w25p32", 0xef2016, 0x0, 64 * 1024, 64, 0) },
+ { INFO("w25x05", 0xef3010, 0, 64 * 1024, 1, SECT_4K) },
+ { INFO("w25x40", 0xef3013, 0, 64 * 1024, 8, SECT_4K) },
+ { INFO("w25x16", 0xef3015, 0, 64 * 1024, 32, SECT_4K) },
+ {
+ INFO("w25q16dw", 0xef6015, 0, 64 * 1024, 32,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ { INFO("w25x32", 0xef3016, 0, 64 * 1024, 64, SECT_4K) },
+ { INFO("w25q20cl", 0xef4012, 0, 64 * 1024, 4, SECT_4K) },
+ { INFO("w25q20bw", 0xef5012, 0, 64 * 1024, 4, SECT_4K) },
+ { INFO("w25q20ew", 0xef6012, 0, 64 * 1024, 4, SECT_4K) },
+ { INFO("w25q32", 0xef4016, 0, 64 * 1024, 64, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ {
+ INFO("w25q32dw", 0xef6016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ INFO("w25q32jv", 0xef7016, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ { INFO("w25x64", 0xef3017, 0, 64 * 1024, 128, SECT_4K) },
+ {
+ INFO("w25q64dw", 0xef6017, 0, 64 * 1024, 128,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ INFO("w25q64jv", 0xef7017, 0, 64 * 1024, 128,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ INFO("w25q128fw", 0xef6018, 0, 64 * 1024, 256,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ INFO("w25q128jv", 0xef7018, 0, 64 * 1024, 256,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ INFO("w25q256fw", 0xef6019, 0, 64 * 1024, 512,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ {
+ INFO("w25q256jw", 0xef7019, 0, 64 * 1024, 512,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+ },
+ { INFO("w25q80", 0xef5014, 0, 64 * 1024, 16, SECT_4K) },
+ { INFO("w25q80bl", 0xef4014, 0, 64 * 1024, 16, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("w25q16cl", 0xef4015, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("w25q64cv", 0xef4017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("w25q128", 0xef4018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("w25q256", 0xef4019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+#endif
+#ifdef CONFIG_SPI_FLASH_XMC
+ /* XMC (Wuhan Xinxin Semiconductor Manufacturing Corp.) */
+ { INFO("XM25QH64A", 0x207017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { INFO("XM25QH128A", 0x207018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+#endif
+ { },
+};
diff --git a/drivers/mtd/spi/spi-nor-tiny.c b/drivers/mtd/spi/spi-nor-tiny.c
new file mode 100644
index 000000000000..c5274ed6b41e
--- /dev/null
+++ b/drivers/mtd/spi/spi-nor-tiny.c
@@ -0,0 +1,810 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Based on m25p80.c, by Mike Lavender (mike at steroidmicros.com), with
+ * influence from lart.c (Abraham Van Der Merwe) and mtd_dataflash.c
+ *
+ * Copyright (C) 2005, Intec Automation Inc.
+ * Copyright (C) 2014, Freescale Semiconductor, Inc.
+ *
+ * Synced from Linux v4.19
+ */
+
+#include <common.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/log2.h>
+#include <linux/math64.h>
+#include <linux/sizes.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/spi-nor.h>
+#include <spi-mem.h>
+#include <spi.h>
+
+#include "sf_internal.h"
+
+/* Define max times to check status register before we give up. */
+
+/*
+ * For everything but full-chip erase; probably could be much smaller, but kept
+ * around for safety for now
+ */
+
+#define HZ CONFIG_SYS_HZ
+
+#define DEFAULT_READY_WAIT_JIFFIES (40UL * HZ)
+
+static int spi_nor_read_write_reg(struct spi_nor *nor, struct spi_mem_op
+ *op, void *buf)
+{
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ op->data.buf.in = buf;
+ else
+ op->data.buf.out = buf;
+ return spi_mem_exec_op(nor->spi, op);
+}
+
+static int spi_nor_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len)
+{
+ struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(code, 1),
+ SPI_MEM_OP_NO_ADDR,
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_IN(len, NULL, 1));
+ int ret;
+
+ ret = spi_nor_read_write_reg(nor, &op, val);
+ if (ret < 0)
+ dev_dbg(&flash->spimem->spi->dev, "error %d reading %x\n", ret,
+ code);
+
+ return ret;
+}
+
+static int spi_nor_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
+{
+ struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(opcode, 1),
+ SPI_MEM_OP_NO_ADDR,
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_OUT(len, NULL, 1));
+
+ return spi_nor_read_write_reg(nor, &op, buf);
+}
+
+static ssize_t spi_nor_read_data(struct spi_nor *nor, loff_t from, size_t len,
+ u_char *buf)
+{
+ struct spi_mem_op op =
+ SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 1),
+ SPI_MEM_OP_ADDR(nor->addr_width, from, 1),
+ SPI_MEM_OP_DUMMY(nor->read_dummy, 1),
+ SPI_MEM_OP_DATA_IN(len, buf, 1));
+ size_t remaining = len;
+ int ret;
+
+ /* get transfer protocols. */
+ op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->read_proto);
+ op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->read_proto);
+ op.dummy.buswidth = op.addr.buswidth;
+ op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->read_proto);
+
+ /* convert the dummy cycles to the number of bytes */
+ op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
+
+ while (remaining) {
+ op.data.nbytes = remaining < UINT_MAX ? remaining : UINT_MAX;
+ ret = spi_mem_adjust_op_size(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ ret = spi_mem_exec_op(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ op.addr.val += op.data.nbytes;
+ remaining -= op.data.nbytes;
+ op.data.buf.in += op.data.nbytes;
+ }
+
+ return len;
+}
+
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+/*
+ * Read configuration register, returning its value in the
+ * location. Return the configuration register value.
+ * Returns negative if error occurred.
+ */
+static int read_cr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = spi_nor_read_reg(nor, SPINOR_OP_RDCR, &val, 1);
+ if (ret < 0) {
+ dev_dbg(nor->dev, "error %d reading CR\n", ret);
+ return ret;
+ }
+
+ return val;
+}
+#endif
+
+/*
+ * Write status register 1 byte
+ * Returns negative if error occurred.
+ */
+static inline int write_sr(struct spi_nor *nor, u8 val)
+{
+ nor->cmd_buf[0] = val;
+ return spi_nor_write_reg(nor, SPINOR_OP_WRSR, nor->cmd_buf, 1);
+}
+
+/*
+ * Set write enable latch with Write Enable command.
+ * Returns negative if error occurred.
+ */
+static inline int write_enable(struct spi_nor *nor)
+{
+ return spi_nor_write_reg(nor, SPINOR_OP_WREN, NULL, 0);
+}
+
+/*
+ * Send write disable instruction to the chip.
+ */
+static inline int write_disable(struct spi_nor *nor)
+{
+ return spi_nor_write_reg(nor, SPINOR_OP_WRDI, NULL, 0);
+}
+
+static inline struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd)
+{
+ return mtd->priv;
+}
+
+static u8 spi_nor_convert_opcode(u8 opcode, const u8 table[][2], size_t size)
+{
+ size_t i;
+
+ for (i = 0; i < size; i++)
+ if (table[i][0] == opcode)
+ return table[i][1];
+
+ /* No conversion found, keep input op code. */
+ return opcode;
+}
+
+static inline u8 spi_nor_convert_3to4_read(u8 opcode)
+{
+ static const u8 spi_nor_3to4_read[][2] = {
+ { SPINOR_OP_READ, SPINOR_OP_READ_4B },
+ { SPINOR_OP_READ_FAST, SPINOR_OP_READ_FAST_4B },
+ { SPINOR_OP_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B },
+ { SPINOR_OP_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B },
+ { SPINOR_OP_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B },
+ { SPINOR_OP_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B },
+ };
+
+ return spi_nor_convert_opcode(opcode, spi_nor_3to4_read,
+ ARRAY_SIZE(spi_nor_3to4_read));
+}
+
+static void spi_nor_set_4byte_opcodes(struct spi_nor *nor,
+ const struct flash_info *info)
+{
+ nor->read_opcode = spi_nor_convert_3to4_read(nor->read_opcode);
+}
+
+/* Enable/disable 4-byte addressing mode. */
+static inline int set_4byte(struct spi_nor *nor, const struct flash_info *info,
+ int enable)
+{
+ int status;
+ bool need_wren = false;
+ u8 cmd;
+
+ switch (JEDEC_MFR(info)) {
+ case SNOR_MFR_ST:
+ case SNOR_MFR_MICRON:
+ /* Some Micron need WREN command; all will accept it */
+ need_wren = true;
+ case SNOR_MFR_MACRONIX:
+ case SNOR_MFR_WINBOND:
+ if (need_wren)
+ write_enable(nor);
+
+ cmd = enable ? SPINOR_OP_EN4B : SPINOR_OP_EX4B;
+ status = spi_nor_write_reg(nor, cmd, NULL, 0);
+ if (need_wren)
+ write_disable(nor);
+
+ if (!status && !enable &&
+ JEDEC_MFR(info) == SNOR_MFR_WINBOND) {
+ /*
+ * On Winbond W25Q256FV, leaving 4byte mode causes
+ * the Extended Address Register to be set to 1, so all
+ * 3-byte-address reads come from the second 16M.
+ * We must clear the register to enable normal behavior.
+ */
+ write_enable(nor);
+ nor->cmd_buf[0] = 0;
+ spi_nor_write_reg(nor, SPINOR_OP_WREAR,
+ nor->cmd_buf, 1);
+ write_disable(nor);
+ }
+
+ return status;
+ default:
+ /* Spansion style */
+ nor->cmd_buf[0] = enable << 7;
+ return spi_nor_write_reg(nor, SPINOR_OP_BRWR, nor->cmd_buf, 1);
+ }
+}
+
+#if defined(CONFIG_SPI_FLASH_SPANSION) || \
+ defined(CONFIG_SPI_FLASH_WINBOND) || \
+ defined(CONFIG_SPI_FLASH_MACRONIX)
+/*
+ * Read the status register, returning its value in the location
+ * Return the status register value.
+ * Returns negative if error occurred.
+ */
+static int read_sr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = spi_nor_read_reg(nor, SPINOR_OP_RDSR, &val, 1);
+ if (ret < 0) {
+ pr_debug("error %d reading SR\n", (int)ret);
+ return ret;
+ }
+
+ return val;
+}
+
+/*
+ * Read the flag status register, returning its value in the location
+ * Return the status register value.
+ * Returns negative if error occurred.
+ */
+static int read_fsr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = spi_nor_read_reg(nor, SPINOR_OP_RDFSR, &val, 1);
+ if (ret < 0) {
+ pr_debug("error %d reading FSR\n", ret);
+ return ret;
+ }
+
+ return val;
+}
+
+static int spi_nor_sr_ready(struct spi_nor *nor)
+{
+ int sr = read_sr(nor);
+
+ if (sr < 0)
+ return sr;
+
+ return !(sr & SR_WIP);
+}
+
+static int spi_nor_fsr_ready(struct spi_nor *nor)
+{
+ int fsr = read_fsr(nor);
+
+ if (fsr < 0)
+ return fsr;
+ return fsr & FSR_READY;
+}
+
+static int spi_nor_ready(struct spi_nor *nor)
+{
+ int sr, fsr;
+
+ sr = spi_nor_sr_ready(nor);
+ if (sr < 0)
+ return sr;
+ fsr = nor->flags & SNOR_F_USE_FSR ? spi_nor_fsr_ready(nor) : 1;
+ if (fsr < 0)
+ return fsr;
+ return sr && fsr;
+}
+
+/*
+ * Service routine to read status register until ready, or timeout occurs.
+ * Returns non-zero if error.
+ */
+static int spi_nor_wait_till_ready_with_timeout(struct spi_nor *nor,
+ unsigned long timeout)
+{
+ unsigned long timebase;
+ int ret;
+
+ timebase = get_timer(0);
+
+ while (get_timer(timebase) < timeout) {
+ ret = spi_nor_ready(nor);
+ if (ret < 0)
+ return ret;
+ if (ret)
+ return 0;
+ }
+
+ dev_err(nor->dev, "flash operation timed out\n");
+
+ return -ETIMEDOUT;
+}
+
+static int spi_nor_wait_till_ready(struct spi_nor *nor)
+{
+ return spi_nor_wait_till_ready_with_timeout(nor,
+ DEFAULT_READY_WAIT_JIFFIES);
+}
+#endif /* CONFIG_SPI_FLASH_SPANSION */
+
+/*
+ * Erase an address range on the nor chip. The address range may extend
+ * one or more erase sectors. Return an error is there is a problem erasing.
+ */
+static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
+{
+ return -ENOTSUPP;
+}
+
+static const struct flash_info *spi_nor_read_id(struct spi_nor *nor)
+{
+ int tmp;
+ u8 id[SPI_NOR_MAX_ID_LEN];
+ const struct flash_info *info;
+
+ tmp = spi_nor_read_reg(nor, SPINOR_OP_RDID, id, SPI_NOR_MAX_ID_LEN);
+ if (tmp < 0) {
+ dev_dbg(nor->dev, "error %d reading JEDEC ID\n", tmp);
+ return ERR_PTR(tmp);
+ }
+
+ info = spi_nor_ids;
+ for (; info->sector_size != 0; info++) {
+ if (info->id_len) {
+ if (!memcmp(info->id, id, info->id_len))
+ return info;
+ }
+ }
+ dev_dbg(nor->dev, "unrecognized JEDEC id bytes: %02x, %02x, %02x\n",
+ id[0], id[1], id[2]);
+ return ERR_PTR(-ENODEV);
+}
+
+static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ int ret;
+
+ dev_dbg(nor->dev, "from 0x%08x, len %zd\n", (u32)from, len);
+
+ while (len) {
+ loff_t addr = from;
+
+ ret = spi_nor_read_data(nor, addr, len, buf);
+ if (ret == 0) {
+ /* We shouldn't see 0-length reads */
+ ret = -EIO;
+ goto read_err;
+ }
+ if (ret < 0)
+ goto read_err;
+
+ *retlen += ret;
+ buf += ret;
+ from += ret;
+ len -= ret;
+ }
+ ret = 0;
+
+read_err:
+ return ret;
+}
+
+/*
+ * Write an address range to the nor chip. Data must be written in
+ * FLASH_PAGESIZE chunks. The address range may be any size provided
+ * it is within the physical boundaries.
+ */
+static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+{
+ return -ENOTSUPP;
+}
+
+#ifdef CONFIG_SPI_FLASH_MACRONIX
+/**
+ * macronix_quad_enable() - set QE bit in Status Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Status Register.
+ *
+ * bit 6 of the Status Register is the QE bit for Macronix like QSPI memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int macronix_quad_enable(struct spi_nor *nor)
+{
+ int ret, val;
+
+ val = read_sr(nor);
+ if (val < 0)
+ return val;
+ if (val & SR_QUAD_EN_MX)
+ return 0;
+
+ write_enable(nor);
+
+ write_sr(nor, val | SR_QUAD_EN_MX);
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ return ret;
+
+ ret = read_sr(nor);
+ if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) {
+ dev_err(nor->dev, "Macronix Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+/*
+ * Write status Register and configuration register with 2 bytes
+ * The first byte will be written to the status register, while the
+ * second byte will be written to the configuration register.
+ * Return negative if error occurred.
+ */
+static int write_sr_cr(struct spi_nor *nor, u8 *sr_cr)
+{
+ int ret;
+
+ write_enable(nor);
+
+ ret = spi_nor_write_reg(nor, SPINOR_OP_WRSR, sr_cr, 2);
+ if (ret < 0) {
+ dev_dbg(nor->dev,
+ "error while writing configuration register\n");
+ return -EINVAL;
+ }
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret) {
+ dev_dbg(nor->dev,
+ "timeout while writing configuration register\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+/**
+ * spansion_read_cr_quad_enable() - set QE bit in Configuration Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Configuration Register.
+ * This function should be used with QSPI memories supporting the Read
+ * Configuration Register (35h) instruction.
+ *
+ * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
+ * memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spansion_read_cr_quad_enable(struct spi_nor *nor)
+{
+ u8 sr_cr[2];
+ int ret;
+
+ /* Check current Quad Enable bit value. */
+ ret = read_cr(nor);
+ if (ret < 0) {
+ dev_dbg(dev, "error while reading configuration register\n");
+ return -EINVAL;
+ }
+
+ if (ret & CR_QUAD_EN_SPAN)
+ return 0;
+
+ sr_cr[1] = ret | CR_QUAD_EN_SPAN;
+
+ /* Keep the current value of the Status Register. */
+ ret = read_sr(nor);
+ if (ret < 0) {
+ dev_dbg(dev, "error while reading status register\n");
+ return -EINVAL;
+ }
+ sr_cr[0] = ret;
+
+ ret = write_sr_cr(nor, sr_cr);
+ if (ret)
+ return ret;
+
+ /* Read back and check it. */
+ ret = read_cr(nor);
+ if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) {
+ dev_dbg(nor->dev, "Spansion Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+#endif /* CONFIG_SPI_FLASH_SPANSION */
+
+struct spi_nor_read_command {
+ u8 num_mode_clocks;
+ u8 num_wait_states;
+ u8 opcode;
+ enum spi_nor_protocol proto;
+};
+
+enum spi_nor_read_command_index {
+ SNOR_CMD_READ,
+ SNOR_CMD_READ_FAST,
+
+ /* Quad SPI */
+ SNOR_CMD_READ_1_1_4,
+
+ SNOR_CMD_READ_MAX
+};
+
+struct spi_nor_flash_parameter {
+ struct spi_nor_hwcaps hwcaps;
+ struct spi_nor_read_command reads[SNOR_CMD_READ_MAX];
+};
+
+static void
+spi_nor_set_read_settings(struct spi_nor_read_command *read,
+ u8 num_mode_clocks,
+ u8 num_wait_states,
+ u8 opcode,
+ enum spi_nor_protocol proto)
+{
+ read->num_mode_clocks = num_mode_clocks;
+ read->num_wait_states = num_wait_states;
+ read->opcode = opcode;
+ read->proto = proto;
+}
+
+static int spi_nor_init_params(struct spi_nor *nor,
+ const struct flash_info *info,
+ struct spi_nor_flash_parameter *params)
+{
+ /* (Fast) Read settings. */
+ params->hwcaps.mask = SNOR_HWCAPS_READ;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ],
+ 0, 0, SPINOR_OP_READ,
+ SNOR_PROTO_1_1_1);
+
+ if (!(info->flags & SPI_NOR_NO_FR)) {
+ params->hwcaps.mask |= SNOR_HWCAPS_READ_FAST;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_FAST],
+ 0, 8, SPINOR_OP_READ_FAST,
+ SNOR_PROTO_1_1_1);
+ }
+
+ if (info->flags & SPI_NOR_QUAD_READ) {
+ params->hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_1_1_4],
+ 0, 8, SPINOR_OP_READ_1_1_4,
+ SNOR_PROTO_1_1_4);
+ }
+
+ return 0;
+}
+
+static int spi_nor_select_read(struct spi_nor *nor,
+ const struct spi_nor_flash_parameter *params,
+ u32 shared_hwcaps)
+{
+ int best_match = shared_hwcaps & SNOR_HWCAPS_READ_MASK;
+ int cmd;
+ const struct spi_nor_read_command *read;
+
+ if (best_match < 0)
+ return -EINVAL;
+
+ if (best_match & SNOR_HWCAPS_READ_1_1_4)
+ cmd = SNOR_CMD_READ_1_1_4;
+ else if (best_match & SNOR_HWCAPS_READ_FAST)
+ cmd = SNOR_CMD_READ_FAST;
+ else
+ cmd = SNOR_CMD_READ;
+
+ read = ¶ms->reads[cmd];
+ nor->read_opcode = read->opcode;
+ nor->read_proto = read->proto;
+
+ /*
+ * In the spi-nor framework, we don't need to make the difference
+ * between mode clock cycles and wait state clock cycles.
+ * Indeed, the value of the mode clock cycles is used by a QSPI
+ * flash memory to know whether it should enter or leave its 0-4-4
+ * (Continuous Read / XIP) mode.
+ * eXecution In Place is out of the scope of the mtd sub-system.
+ * Hence we choose to merge both mode and wait state clock cycles
+ * into the so called dummy clock cycles.
+ */
+ nor->read_dummy = read->num_mode_clocks + read->num_wait_states;
+ return 0;
+}
+
+static int spi_nor_setup(struct spi_nor *nor, const struct flash_info *info,
+ const struct spi_nor_flash_parameter *params,
+ const struct spi_nor_hwcaps *hwcaps)
+{
+ u32 shared_mask;
+ int err;
+
+ /*
+ * Keep only the hardware capabilities supported by both the SPI
+ * controller and the SPI flash memory.
+ */
+ shared_mask = hwcaps->mask & params->hwcaps.mask;
+
+ /* Select the (Fast) Read command. */
+ err = spi_nor_select_read(nor, params, shared_mask);
+ if (err) {
+ dev_dbg(nor->dev,
+ "can't select read settings supported by both the SPI controller and memory.\n");
+ return err;
+ }
+
+ /* Enable Quad I/O if needed. */
+ if (spi_nor_get_protocol_width(nor->read_proto) == 4) {
+ switch (JEDEC_MFR(info)) {
+#ifdef CONFIG_SPI_FLASH_MACRONIX
+ case SNOR_MFR_MACRONIX:
+ err = macronix_quad_enable(nor);
+ break;
+#endif
+ case SNOR_MFR_ST:
+ case SNOR_MFR_MICRON:
+ break;
+
+ default:
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+ /* Kept only for backward compatibility purpose. */
+ err = spansion_read_cr_quad_enable(nor);
+#endif
+ break;
+ }
+ }
+ if (err) {
+ dev_dbg(nor->dev, "quad mode not supported\n");
+ return err;
+ }
+
+ return 0;
+}
+
+static int spi_nor_init(struct spi_nor *nor)
+{
+ if (nor->addr_width == 4 &&
+ (JEDEC_MFR(nor->info) != SNOR_MFR_SPANSION) &&
+ !(nor->info->flags & SPI_NOR_4B_OPCODES)) {
+ /*
+ * If the RESET# pin isn't hooked up properly, or the system
+ * otherwise doesn't perform a reset command in the boot
+ * sequence, it's impossible to 100% protect against unexpected
+ * reboots (e.g., crashes). Warn the user (or hopefully, system
+ * designer) that this is bad.
+ */
+ if (nor->flags & SNOR_F_BROKEN_RESET)
+ printf("enabling reset hack; may not recover from unexpected reboots\n");
+ set_4byte(nor, nor->info, 1);
+ }
+
+ return 0;
+}
+
+int spi_nor_scan(struct spi_nor *nor)
+{
+ struct spi_nor_flash_parameter params;
+ const struct flash_info *info = NULL;
+ struct mtd_info *mtd = &nor->mtd;
+ struct spi_nor_hwcaps hwcaps = {
+ .mask = SNOR_HWCAPS_READ |
+ SNOR_HWCAPS_READ_FAST
+ };
+ struct spi_slave *spi = nor->spi;
+ int ret;
+
+ /* Reset SPI protocol for all commands. */
+ nor->reg_proto = SNOR_PROTO_1_1_1;
+ nor->read_proto = SNOR_PROTO_1_1_1;
+ nor->write_proto = SNOR_PROTO_1_1_1;
+
+ if (spi->mode & SPI_RX_QUAD)
+ hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4;
+
+ info = spi_nor_read_id(nor);
+ if (IS_ERR_OR_NULL(info))
+ return -ENOENT;
+ /* Parse the Serial Flash Discoverable Parameters table. */
+ ret = spi_nor_init_params(nor, info, ¶ms);
+ if (ret)
+ return ret;
+
+ mtd->name = "spi-flash";
+ mtd->priv = nor;
+ mtd->type = MTD_NORFLASH;
+ mtd->writesize = 1;
+ mtd->flags = MTD_CAP_NORFLASH;
+ mtd->size = info->sector_size * info->n_sectors;
+ mtd->_erase = spi_nor_erase;
+ mtd->_read = spi_nor_read;
+ mtd->_write = spi_nor_write;
+
+ nor->size = mtd->size;
+
+ if (info->flags & USE_FSR)
+ nor->flags |= SNOR_F_USE_FSR;
+ if (info->flags & USE_CLSR)
+ nor->flags |= SNOR_F_USE_CLSR;
+
+ if (info->flags & SPI_NOR_NO_FR)
+ params.hwcaps.mask &= ~SNOR_HWCAPS_READ_FAST;
+
+ /*
+ * Configure the SPI memory:
+ * - select op codes for (Fast) Read, Page Program and Sector Erase.
+ * - set the number of dummy cycles (mode cycles + wait states).
+ * - set the SPI protocols for register and memory accesses.
+ * - set the Quad Enable bit if needed (required by SPI x-y-4 protos).
+ */
+ ret = spi_nor_setup(nor, info, ¶ms, &hwcaps);
+ if (ret)
+ return ret;
+
+ if (nor->addr_width) {
+ /* already configured from SFDP */
+ } else if (info->addr_width) {
+ nor->addr_width = info->addr_width;
+ } else if (mtd->size > 0x1000000) {
+ /* enable 4-byte addressing if the device exceeds 16MiB */
+ nor->addr_width = 4;
+ if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
+ info->flags & SPI_NOR_4B_OPCODES)
+ spi_nor_set_4byte_opcodes(nor, info);
+ } else {
+ nor->addr_width = 3;
+ }
+
+ if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) {
+ dev_dbg(dev, "address width is too large: %u\n",
+ nor->addr_width);
+ return -EINVAL;
+ }
+
+ /* Send all the required SPI flash commands to initialize device */
+ nor->info = info;
+ ret = spi_nor_init(nor);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(spi_nor_scan);
+
+/* U-Boot specific functions, need to extend MTD to support these */
+int spi_flash_cmd_get_sw_write_prot(struct spi_nor *nor)
+{
+ return -ENOTSUPP;
+}
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Huang Shijie <shijie8@gmail.com>");
+MODULE_AUTHOR("Mike Lavender");
+MODULE_DESCRIPTION("framework for SPI NOR");
--
2.20.1
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 08/11] configs: Enable SPI_FLASH_TINY for resource constrained boards
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (6 preceding siblings ...)
2018-12-21 6:38 ` [U-Boot] [PATCH v2 07/11] mtd: spi: Add lightweight SPI flash stack for SPL Vignesh R
@ 2018-12-21 6:38 ` Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 09/11] configs: Remove SF_DUAL_FLASH Vignesh R
` (6 subsequent siblings)
14 siblings, 0 replies; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
Enable SPI_FLASH_TINY to reduce SPL size on boards that are too short of
memory. SPI_FLASH_TINY provides a read only implementation of SPI NOR
stack for use in SPL.
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
configs/axm_defconfig | 1 +
configs/da850_am18xxevm_defconfig | 1 +
configs/da850evm_nand_defconfig | 2 +-
configs/db-88f6820-gp_defconfig | 1 +
configs/porter_defconfig | 1 +
configs/stout_defconfig | 1 +
configs/taurus_defconfig | 3 ++-
configs/turris_omnia_defconfig | 2 +-
8 files changed, 9 insertions(+), 3 deletions(-)
diff --git a/configs/axm_defconfig b/configs/axm_defconfig
index 89d6b6f2012c..7aa7a4a5c6e7 100644
--- a/configs/axm_defconfig
+++ b/configs/axm_defconfig
@@ -20,6 +20,7 @@ CONFIG_BOOTARGS="\0addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SPL_SPI_FLASH_TINY=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_HUSH_PARSER=y
# CONFIG_CMD_BDI is not set
diff --git a/configs/da850_am18xxevm_defconfig b/configs/da850_am18xxevm_defconfig
index 58745fec8267..053a1f6fd65a 100644
--- a/configs/da850_am18xxevm_defconfig
+++ b/configs/da850_am18xxevm_defconfig
@@ -19,6 +19,7 @@ CONFIG_VERSION_VARIABLE=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_BOARD_INIT=y
+CONFIG_SPL_SPI_FLASH_TINY=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot > "
diff --git a/configs/da850evm_nand_defconfig b/configs/da850evm_nand_defconfig
index 5c498749d604..d7aa9426b4c7 100644
--- a/configs/da850evm_nand_defconfig
+++ b/configs/da850evm_nand_defconfig
@@ -18,11 +18,11 @@ CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SPL_SPI_FLASH_TINY=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot > "
CONFIG_CRC32_VERIFY=y
-# CONFIG_CMD_EEPROM is not set
CONFIG_CMD_DM=y
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_GPT is not set
diff --git a/configs/db-88f6820-gp_defconfig b/configs/db-88f6820-gp_defconfig
index 413010c4efb1..15ae81450443 100644
--- a/configs/db-88f6820-gp_defconfig
+++ b/configs/db-88f6820-gp_defconfig
@@ -19,6 +19,7 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_SPI_FLASH_TINY=y
CONFIG_SPL_SPI_LOAD=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_I2C=y
diff --git a/configs/porter_defconfig b/configs/porter_defconfig
index d51db3d5cb28..6fa750a03a7d 100644
--- a/configs/porter_defconfig
+++ b/configs/porter_defconfig
@@ -23,6 +23,7 @@ CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
CONFIG_SPL_RAM_SUPPORT=y
CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_SPI_FLASH_TINY=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_SPL_YMODEM_SUPPORT=y
CONFIG_HUSH_PARSER=y
diff --git a/configs/stout_defconfig b/configs/stout_defconfig
index acd05564f327..d99d97b60b2f 100644
--- a/configs/stout_defconfig
+++ b/configs/stout_defconfig
@@ -23,6 +23,7 @@ CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
CONFIG_SPL_RAM_SUPPORT=y
CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_SPI_FLASH_TINY=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_SPL_YMODEM_SUPPORT=y
CONFIG_HUSH_PARSER=y
diff --git a/configs/taurus_defconfig b/configs/taurus_defconfig
index e53e075d4825..e9d9f86d51b3 100644
--- a/configs/taurus_defconfig
+++ b/configs/taurus_defconfig
@@ -22,6 +22,7 @@ CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(boots
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SPL_SPI_FLASH_TINY=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
@@ -60,7 +61,7 @@ CONFIG_USB_GADGET_MANUFACTURER="Siemens AG"
CONFIG_USB_GADGET_VENDOR_NUM=0x0908
CONFIG_USB_GADGET_PRODUCT_NUM=0x02d2
CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_USE_TINY_PRINTF=y
CONFIG_WDT=y
CONFIG_WDT_AT91=y
CONFIG_AT91_HW_WDT_TIMEOUT=y
+CONFIG_USE_TINY_PRINTF=y
diff --git a/configs/turris_omnia_defconfig b/configs/turris_omnia_defconfig
index 38c5de18bb2d..9279431df8aa 100644
--- a/configs/turris_omnia_defconfig
+++ b/configs/turris_omnia_defconfig
@@ -20,6 +20,7 @@ CONFIG_MISC_INIT_R=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_SPI_FLASH_TINY=y
CONFIG_SPL_SPI_LOAD=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_I2C=y
@@ -52,6 +53,5 @@ CONFIG_KIRKWOOD_SPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
CONFIG_WDT=y
CONFIG_WDT_ORION=y
--
2.20.1
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 09/11] configs: Remove SF_DUAL_FLASH
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (7 preceding siblings ...)
2018-12-21 6:38 ` [U-Boot] [PATCH v2 08/11] configs: Enable SPI_FLASH_TINY for resource constrained boards Vignesh R
@ 2018-12-21 6:38 ` Vignesh R
2019-01-25 14:47 ` Jagan Teki
2018-12-21 6:38 ` [U-Boot] [PATCH v2 10/11] configs: Don't use SPI_FLASH_BAR as default Vignesh R
` (5 subsequent siblings)
14 siblings, 1 reply; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
SF_DUAL_FLASH claims to enable support for SF_DUAL_STACKED_FLASH and
SF_DUAL_PARALLEL_FLASH. But, in current U-Boot code, grepping for above
enums yield no user and therefore support seems to be incomplete. Remove
these configs so as to avoid confusion.
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
configs/topic_miamilite_defconfig | 1 -
configs/topic_miamiplus_defconfig | 1 -
configs/xilinx_zynqmp_mini_qspi_defconfig | 1 -
configs/xilinx_zynqmp_zc1232_revA_defconfig | 1 -
configs/xilinx_zynqmp_zc1254_revA_defconfig | 1 -
configs/xilinx_zynqmp_zc1275_revA_defconfig | 1 -
configs/xilinx_zynqmp_zc1275_revB_defconfig | 1 -
configs/xilinx_zynqmp_zcu104_revA_defconfig | 1 -
configs/xilinx_zynqmp_zcu104_revC_defconfig | 1 -
configs/xilinx_zynqmp_zcu106_revA_defconfig | 1 -
doc/SPI/README.dual-flash | 92 ---------------------
include/configs/socfpga_stratix10_socdk.h | 1 -
12 files changed, 103 deletions(-)
delete mode 100644 doc/SPI/README.dual-flash
diff --git a/configs/topic_miamilite_defconfig b/configs/topic_miamilite_defconfig
index 4486975f9503..a2ff87a55029 100644
--- a/configs/topic_miamilite_defconfig
+++ b/configs/topic_miamilite_defconfig
@@ -41,7 +41,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
-CONFIG_SF_DUAL_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_DEBUG_UART_ZYNQ=y
diff --git a/configs/topic_miamiplus_defconfig b/configs/topic_miamiplus_defconfig
index ee83f0545bd5..74deff0a19c8 100644
--- a/configs/topic_miamiplus_defconfig
+++ b/configs/topic_miamiplus_defconfig
@@ -40,7 +40,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
-CONFIG_SF_DUAL_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
# CONFIG_NETDEVICES is not set
diff --git a/configs/xilinx_zynqmp_mini_qspi_defconfig b/configs/xilinx_zynqmp_mini_qspi_defconfig
index de7bf079551f..1138faffcc39 100644
--- a/configs/xilinx_zynqmp_mini_qspi_defconfig
+++ b/configs/xilinx_zynqmp_mini_qspi_defconfig
@@ -56,7 +56,6 @@ CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
-CONFIG_SF_DUAL_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zc1232_revA_defconfig b/configs/xilinx_zynqmp_zc1232_revA_defconfig
index 7521fc4e34e4..4700956dd2db 100644
--- a/configs/xilinx_zynqmp_zc1232_revA_defconfig
+++ b/configs/xilinx_zynqmp_zc1232_revA_defconfig
@@ -38,7 +38,6 @@ CONFIG_MISC=y
CONFIG_DM_MMC=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
-CONFIG_SF_DUAL_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zc1254_revA_defconfig b/configs/xilinx_zynqmp_zc1254_revA_defconfig
index e0822b931edb..0570414a0532 100644
--- a/configs/xilinx_zynqmp_zc1254_revA_defconfig
+++ b/configs/xilinx_zynqmp_zc1254_revA_defconfig
@@ -38,7 +38,6 @@ CONFIG_MISC=y
CONFIG_DM_MMC=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
-CONFIG_SF_DUAL_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zc1275_revA_defconfig b/configs/xilinx_zynqmp_zc1275_revA_defconfig
index 3afed6973709..7c83f7036814 100644
--- a/configs/xilinx_zynqmp_zc1275_revA_defconfig
+++ b/configs/xilinx_zynqmp_zc1275_revA_defconfig
@@ -38,7 +38,6 @@ CONFIG_MISC=y
CONFIG_DM_MMC=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
-CONFIG_SF_DUAL_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zc1275_revB_defconfig b/configs/xilinx_zynqmp_zc1275_revB_defconfig
index 7e31b1112f8f..e2aade7606bf 100644
--- a/configs/xilinx_zynqmp_zc1275_revB_defconfig
+++ b/configs/xilinx_zynqmp_zc1275_revB_defconfig
@@ -41,7 +41,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
-CONFIG_SF_DUAL_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zcu104_revA_defconfig b/configs/xilinx_zynqmp_zcu104_revA_defconfig
index ff57ca8674e6..b612ce213224 100644
--- a/configs/xilinx_zynqmp_zcu104_revA_defconfig
+++ b/configs/xilinx_zynqmp_zcu104_revA_defconfig
@@ -58,7 +58,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
-CONFIG_SF_DUAL_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zcu104_revC_defconfig b/configs/xilinx_zynqmp_zcu104_revC_defconfig
index 0357b1744545..2fb66b2177ab 100644
--- a/configs/xilinx_zynqmp_zcu104_revC_defconfig
+++ b/configs/xilinx_zynqmp_zcu104_revC_defconfig
@@ -59,7 +59,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
-CONFIG_SF_DUAL_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zcu106_revA_defconfig b/configs/xilinx_zynqmp_zcu106_revA_defconfig
index 210c9a347fb2..20e210ec3822 100644
--- a/configs/xilinx_zynqmp_zcu106_revA_defconfig
+++ b/configs/xilinx_zynqmp_zcu106_revA_defconfig
@@ -67,7 +67,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
-CONFIG_SF_DUAL_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/doc/SPI/README.dual-flash b/doc/SPI/README.dual-flash
deleted file mode 100644
index 6c88d65dd49f..000000000000
--- a/doc/SPI/README.dual-flash
+++ /dev/null
@@ -1,92 +0,0 @@
-SPI/QSPI Dual flash connection modes:
-=====================================
-
-This describes how SPI/QSPI flash memories are connected to a given
-controller in a single chip select line.
-
-Current spi_flash framework supports, single flash memory connected
-to a given controller with single chip select line, but there are some
-hw logics(ex: xilinx zynq qspi) that describes two/dual memories are
-connected with a single chip select line from a controller.
-
-"dual_flash" from include/spi.h describes these types of connection mode
-
-Possible connections:
---------------------
-SF_SINGLE_FLASH:
- - single spi flash memory connected with single chip select line.
-
- +------------+ CS +---------------+
- | |----------------------->| |
- | Controller | I0[3:0] | Flash memory |
- | SPI/QSPI |<======================>| (SPI/QSPI) |
- | | CLK | |
- | |----------------------->| |
- +------------+ +---------------+
-
-SF_DUAL_STACKED_FLASH:
- - dual spi/qspi flash memories are connected with a single chipselect
- line and these two memories are operating stacked fasion with shared buses.
- - xilinx zynq qspi controller has implemented this feature [1]
-
- +------------+ CS +---------------+
- | |---------------------->| |
- | | I0[3:0] | Upper Flash |
- | | +=========>| memory |
- | | | CLK | (SPI/QSPI) |
- | | | +---->| |
- | Controller | CS | | +---------------+
- | SPI/QSPI |------------|----|---->| |
- | | I0[3:0] | | | Lower Flash |
- | |<===========+====|====>| memory |
- | | CLK | | (SPI/QSPI) |
- | |-----------------+---->| |
- +------------+ +---------------+
-
- - two memory flash devices should has same hw part attributes (like size,
- vendor..etc)
- - Configurations:
- on LQSPI_CFG register, Enable TWO_MEM[BIT:30] on LQSPI_CFG
- Enable U_PAGE[BIT:28] if U_PAGE flag set - upper memory
- Disable U_PAGE[BIT:28] if U_PAGE flag unset - lower memory
- - Operation:
- accessing memories serially like one after another.
- by default, if U_PAGE is unset lower memory should accessible,
- once user wants to access upper memory need to set U_PAGE.
-
-SPI_FLASH_CONN_DUALPARALLEL:
- - dual spi/qspi flash memories are connected with a single chipselect
- line and these two memories are operating parallel with separate buses.
- - xilinx zynq qspi controller has implemented this feature [1]
-
- +-------------+ CS +---------------+
- | |---------------------->| |
- | | I0[3:0] | Upper Flash |
- | |<=====================>| memory |
- | | CLK | (SPI/QSPI) |
- | |---------------------->| |
- | Controller | CS +---------------+
- | SPI/QSPI |---------------------->| |
- | | I0[3:0] | Lower Flash |
- | |<=====================>| memory |
- | | CLK | (SPI/QSPI) |
- | |---------------------->| |
- +-------------+ +---------------+
-
- - two memory flash devices should has same hw part attributes (like size,
- vendor..etc)
- - Configurations:
- Need to enable SEP_BUS[BIT:29],TWO_MEM[BIT:30] on LQSPI_CFG register.
- - Operation:
- Even bits, i.e. bit 0, 2, 4 ., of a data word is located in the lower memory
- and odd bits, i.e. bit 1, 3, 5, ., of a data word is located in the upper memory.
-
-Note: Technically there is only one CS line from the controller, but
-zynq qspi controller has an internal hw logic to enable additional CS
-when controller is configured for dual memories.
-
-[1] http://www.xilinx.com/support/documentation/user_guides/ug585-Zynq-7000-TRM.pdf
-
---
-Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
-05-01-2014.
diff --git a/include/configs/socfpga_stratix10_socdk.h b/include/configs/socfpga_stratix10_socdk.h
index e190b3d9889d..0b705e6adb80 100644
--- a/include/configs/socfpga_stratix10_socdk.h
+++ b/include/configs/socfpga_stratix10_socdk.h
@@ -57,7 +57,6 @@
*/
#ifdef CONFIG_CADENCE_QSPI
/* Enable it if you want to use dual-stacked mode */
-#undef CONFIG_SF_DUAL_FLASH
/*#define CONFIG_QSPI_RBF_ADDR 0x720000*/
/* Flash device info */
--
2.20.1
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 10/11] configs: Don't use SPI_FLASH_BAR as default
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (8 preceding siblings ...)
2018-12-21 6:38 ` [U-Boot] [PATCH v2 09/11] configs: Remove SF_DUAL_FLASH Vignesh R
@ 2018-12-21 6:38 ` Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 11/11] MAINTAINERS: Add an entry for SPI NOR Vignesh R
` (4 subsequent siblings)
14 siblings, 0 replies; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
arch/arm/mach-omap2/am33xx/Kconfig | 1 -
configs/alt_defconfig | 1 -
configs/am57xx_evm_defconfig | 1 -
configs/am57xx_hs_evm_defconfig | 1 -
configs/ap121_defconfig | 1 -
configs/ap143_defconfig | 1 -
configs/avnet_ultra96_rev1_defconfig | 1 -
configs/axs101_defconfig | 1 -
configs/axs103_defconfig | 1 -
configs/bg0900_defconfig | 1 -
configs/blanche_defconfig | 1 -
configs/cl-som-am57x_defconfig | 1 -
configs/clearfog_defconfig | 1 -
configs/cm_t43_defconfig | 1 -
configs/db-88f6820-amc_defconfig | 1 -
configs/display5_defconfig | 1 -
configs/display5_factory_defconfig | 1 -
configs/dra7xx_evm_defconfig | 1 -
configs/dra7xx_hs_evm_defconfig | 1 -
configs/ds109_defconfig | 1 -
configs/ds414_defconfig | 1 -
configs/evb-rv1108_defconfig | 1 -
configs/gose_defconfig | 1 -
configs/helios4_defconfig | 1 -
configs/k2g_evm_defconfig | 1 -
configs/k2g_hs_evm_defconfig | 1 -
configs/koelsch_defconfig | 1 -
configs/lager_defconfig | 1 -
configs/maxbcm_defconfig | 1 -
configs/mt7629_rfb_defconfig | 1 -
configs/mx6sxsabreauto_defconfig | 1 -
configs/mx6sxsabresd_defconfig | 1 -
configs/mx6ul_14x14_evk_defconfig | 1 -
configs/mx6ul_9x9_evk_defconfig | 1 -
configs/mx6ull_14x14_evk_defconfig | 1 -
configs/mx6ull_14x14_evk_plugin_defconfig | 1 -
configs/mx7dsabresd_qspi_defconfig | 1 -
configs/porter_defconfig | 1 -
configs/r8a77970_eagle_defconfig | 1 -
configs/silk_defconfig | 1 -
configs/socfpga_arria5_defconfig | 1 -
configs/socfpga_cyclone5_defconfig | 1 -
configs/socfpga_is1_defconfig | 1 -
configs/socfpga_sockit_defconfig | 1 -
configs/socfpga_socrates_defconfig | 1 -
configs/socfpga_sr1500_defconfig | 1 -
configs/socfpga_stratix10_defconfig | 1 -
configs/stout_defconfig | 1 -
configs/topic_miami_defconfig | 1 -
configs/topic_miamilite_defconfig | 1 -
configs/topic_miamiplus_defconfig | 1 -
configs/xilinx_versal_virt_defconfig | 1 -
configs/xilinx_zynqmp_mini_qspi_defconfig | 1 -
configs/xilinx_zynqmp_zc1232_revA_defconfig | 1 -
configs/xilinx_zynqmp_zc1254_revA_defconfig | 1 -
configs/xilinx_zynqmp_zc1275_revA_defconfig | 1 -
configs/xilinx_zynqmp_zc1275_revB_defconfig | 1 -
configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 -
configs/xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 1 -
configs/xilinx_zynqmp_zc1751_xm018_dc4_defconfig | 1 -
configs/xilinx_zynqmp_zcu100_revC_defconfig | 1 -
configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 1 -
configs/xilinx_zynqmp_zcu102_revA_defconfig | 1 -
configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 -
configs/xilinx_zynqmp_zcu104_revA_defconfig | 1 -
configs/xilinx_zynqmp_zcu104_revC_defconfig | 1 -
configs/xilinx_zynqmp_zcu106_revA_defconfig | 1 -
configs/xilinx_zynqmp_zcu111_revA_defconfig | 1 -
configs/zynq_cc108_defconfig | 1 -
configs/zynq_cse_qspi_defconfig | 1 -
configs/zynq_dlc20_rev1_0_defconfig | 1 -
configs/zynq_microzed_defconfig | 1 -
configs/zynq_minized_defconfig | 1 -
configs/zynq_z_turn_defconfig | 1 -
configs/zynq_zc702_defconfig | 1 -
configs/zynq_zc706_defconfig | 1 -
configs/zynq_zc770_xm010_defconfig | 1 -
configs/zynq_zc770_xm013_defconfig | 1 -
configs/zynq_zed_defconfig | 1 -
configs/zynq_zybo_defconfig | 1 -
configs/zynq_zybo_z7_defconfig | 1 -
doc/SPI/README.ti_qspi_dra_test | 1 -
drivers/spi/Kconfig | 5 +++++
include/configs/T102xQDS.h | 1 -
include/configs/T102xRDB.h | 1 -
include/configs/T104xRDB.h | 1 -
include/configs/T208xQDS.h | 1 -
include/configs/T208xRDB.h | 1 -
include/configs/gw_ventana.h | 1 -
include/configs/km/kmp204x-common.h | 1 -
include/configs/ls1021aiot.h | 1 -
91 files changed, 5 insertions(+), 90 deletions(-)
diff --git a/arch/arm/mach-omap2/am33xx/Kconfig b/arch/arm/mach-omap2/am33xx/Kconfig
index 57284c4ae122..1bc87ebcad2d 100644
--- a/arch/arm/mach-omap2/am33xx/Kconfig
+++ b/arch/arm/mach-omap2/am33xx/Kconfig
@@ -230,7 +230,6 @@ config TARGET_AM43XX_EVM
imply DM_I2C
imply DM_SPI
imply DM_SPI_FLASH
- imply SPI_FLASH_BAR
imply SPL_ENV_SUPPORT
imply SPL_EXT_SUPPORT
imply SPL_FAT_SUPPORT
diff --git a/configs/alt_defconfig b/configs/alt_defconfig
index 396ed5eaf287..44f1e1c51a4c 100644
--- a/configs/alt_defconfig
+++ b/configs/alt_defconfig
@@ -65,7 +65,6 @@ CONFIG_RENESAS_SDHI=y
CONFIG_MTD=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHY_MICREL=y
diff --git a/configs/am57xx_evm_defconfig b/configs/am57xx_evm_defconfig
index aa8283033e53..7e14ae0ccd97 100644
--- a/configs/am57xx_evm_defconfig
+++ b/configs/am57xx_evm_defconfig
@@ -56,7 +56,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_OMAP_HS=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
diff --git a/configs/am57xx_hs_evm_defconfig b/configs/am57xx_hs_evm_defconfig
index 09f3774b6d0e..ef8e7ced30fc 100644
--- a/configs/am57xx_hs_evm_defconfig
+++ b/configs/am57xx_hs_evm_defconfig
@@ -59,7 +59,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_OMAP_HS=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
diff --git a/configs/ap121_defconfig b/configs/ap121_defconfig
index 5d54267cd345..c9dbe4d72174 100644
--- a/configs/ap121_defconfig
+++ b/configs/ap121_defconfig
@@ -35,7 +35,6 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_SPI_FLASH_EON=y
CONFIG_SPI_FLASH_GIGADEVICE=y
diff --git a/configs/ap143_defconfig b/configs/ap143_defconfig
index 83eb583b563e..7c1a296e2775 100644
--- a/configs/ap143_defconfig
+++ b/configs/ap143_defconfig
@@ -34,7 +34,6 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
# CONFIG_NET is not set
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_SPI_FLASH_EON=y
CONFIG_SPI_FLASH_GIGADEVICE=y
diff --git a/configs/avnet_ultra96_rev1_defconfig b/configs/avnet_ultra96_rev1_defconfig
index 9ca884e4056a..542700a4ae43 100644
--- a/configs/avnet_ultra96_rev1_defconfig
+++ b/configs/avnet_ultra96_rev1_defconfig
@@ -60,7 +60,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/axs101_defconfig b/configs/axs101_defconfig
index b4621c359fc6..b77ecc178151 100644
--- a/configs/axs101_defconfig
+++ b/configs/axs101_defconfig
@@ -38,7 +38,6 @@ CONFIG_MMC=y
CONFIG_MMC_DW=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_DM_ETH=y
diff --git a/configs/axs103_defconfig b/configs/axs103_defconfig
index e7894d297cda..f42b694ca78b 100644
--- a/configs/axs103_defconfig
+++ b/configs/axs103_defconfig
@@ -38,7 +38,6 @@ CONFIG_MMC=y
CONFIG_MMC_DW=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_DM_ETH=y
diff --git a/configs/bg0900_defconfig b/configs/bg0900_defconfig
index 6de81621cd45..2bafc793bc80 100644
--- a/configs/bg0900_defconfig
+++ b/configs/bg0900_defconfig
@@ -32,7 +32,6 @@ CONFIG_DOS_PARTITION=y
CONFIG_NAND=y
CONFIG_NAND_MXS=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_MII=y
CONFIG_CONS_INDEX=0
diff --git a/configs/blanche_defconfig b/configs/blanche_defconfig
index 244ab22f6fc1..c5042d885f4e 100644
--- a/configs/blanche_defconfig
+++ b/configs/blanche_defconfig
@@ -49,7 +49,6 @@ CONFIG_MTD_NOR_FLASH=y
CONFIG_FLASH_CFI_DRIVER=y
CONFIG_SYS_FLASH_CFI=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SMC911X=y
CONFIG_SMC911X_BASE=0x18000000
diff --git a/configs/cl-som-am57x_defconfig b/configs/cl-som-am57x_defconfig
index c5337f909e95..6e174067e22a 100644
--- a/configs/cl-som-am57x_defconfig
+++ b/configs/cl-som-am57x_defconfig
@@ -37,7 +37,6 @@ CONFIG_LED_STATUS_BIT=37
CONFIG_LED_STATUS_STATE=2
CONFIG_MMC_OMAP_HS=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_SPI_FLASH_EON=y
CONFIG_SPI_FLASH_GIGADEVICE=y
diff --git a/configs/clearfog_defconfig b/configs/clearfog_defconfig
index 2e59686291b7..aba9ff06a32d 100644
--- a/configs/clearfog_defconfig
+++ b/configs/clearfog_defconfig
@@ -48,7 +48,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_SDMA=y
CONFIG_MMC_SDHCI_MV=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHY_MARVELL=y
diff --git a/configs/cm_t43_defconfig b/configs/cm_t43_defconfig
index eb4a8f5a3308..b77b1c2c3c03 100644
--- a/configs/cm_t43_defconfig
+++ b/configs/cm_t43_defconfig
@@ -49,7 +49,6 @@ CONFIG_DM_GPIO=y
CONFIG_MMC_OMAP_HS=y
CONFIG_NAND=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_SPI_FLASH_EON=y
CONFIG_SPI_FLASH_GIGADEVICE=y
diff --git a/configs/db-88f6820-amc_defconfig b/configs/db-88f6820-amc_defconfig
index dd58198a5469..0f42935f394a 100644
--- a/configs/db-88f6820-amc_defconfig
+++ b/configs/db-88f6820-amc_defconfig
@@ -49,7 +49,6 @@ CONFIG_SYS_I2C_MVTWSI=y
CONFIG_NAND=y
CONFIG_NAND_PXA3XX=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHY_MARVELL=y
diff --git a/configs/display5_defconfig b/configs/display5_defconfig
index e6162e3cfb7c..a07c5d812249 100644
--- a/configs/display5_defconfig
+++ b/configs/display5_defconfig
@@ -64,7 +64,6 @@ CONFIG_SYS_BOOTCOUNT_ADDR=0x020CC068
CONFIG_FSL_ESDHC=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
diff --git a/configs/display5_factory_defconfig b/configs/display5_factory_defconfig
index 6ef85e246ccf..44980864798e 100644
--- a/configs/display5_factory_defconfig
+++ b/configs/display5_factory_defconfig
@@ -65,7 +65,6 @@ CONFIG_DFU_SF=y
CONFIG_FSL_ESDHC=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
diff --git a/configs/dra7xx_evm_defconfig b/configs/dra7xx_evm_defconfig
index 2b6606f9e205..338319e2df83 100644
--- a/configs/dra7xx_evm_defconfig
+++ b/configs/dra7xx_evm_defconfig
@@ -67,7 +67,6 @@ CONFIG_SPL_MMC_HS200_SUPPORT=y
CONFIG_MMC_OMAP_HS=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_DM_ETH=y
CONFIG_DRIVER_TI_CPSW=y
diff --git a/configs/dra7xx_hs_evm_defconfig b/configs/dra7xx_hs_evm_defconfig
index 725acb527942..4d71b1308bea 100644
--- a/configs/dra7xx_hs_evm_defconfig
+++ b/configs/dra7xx_hs_evm_defconfig
@@ -65,7 +65,6 @@ CONFIG_MMC_HS200_SUPPORT=y
CONFIG_MMC_OMAP_HS=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_DM_ETH=y
CONFIG_DRIVER_TI_CPSW=y
diff --git a/configs/ds109_defconfig b/configs/ds109_defconfig
index 352403e57385..3e4e71bcbf4e 100644
--- a/configs/ds109_defconfig
+++ b/configs/ds109_defconfig
@@ -25,7 +25,6 @@ CONFIG_SYS_I2C_MVTWSI=y
# CONFIG_MMC is not set
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_MVGBE=y
CONFIG_MII=y
diff --git a/configs/ds414_defconfig b/configs/ds414_defconfig
index 5325bd9968a8..8e1272a3817e 100644
--- a/configs/ds414_defconfig
+++ b/configs/ds414_defconfig
@@ -44,7 +44,6 @@ CONFIG_SPL_OF_TRANSLATE=y
# CONFIG_MMC is not set
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_MARVELL=y
diff --git a/configs/evb-rv1108_defconfig b/configs/evb-rv1108_defconfig
index 2ef041f2c50e..c267213a9d97 100644
--- a/configs/evb-rv1108_defconfig
+++ b/configs/evb-rv1108_defconfig
@@ -29,7 +29,6 @@ CONFIG_FASTBOOT_FLASH_MMC_DEV=1
CONFIG_ROCKCHIP_GPIO=y
CONFIG_SYS_I2C_ROCKCHIP=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_GIGADEVICE=y
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_SPI_FLASH_MTD=y
diff --git a/configs/gose_defconfig b/configs/gose_defconfig
index 0368c659633e..a5afb3c5699b 100644
--- a/configs/gose_defconfig
+++ b/configs/gose_defconfig
@@ -64,7 +64,6 @@ CONFIG_RENESAS_SDHI=y
CONFIG_MTD=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHY_MICREL=y
diff --git a/configs/helios4_defconfig b/configs/helios4_defconfig
index 3bb4622fbee0..3e2488e6371f 100644
--- a/configs/helios4_defconfig
+++ b/configs/helios4_defconfig
@@ -48,7 +48,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_SDMA=y
CONFIG_MMC_SDHCI_MV=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_PHY_GIGE=y
CONFIG_MVNETA=y
diff --git a/configs/k2g_evm_defconfig b/configs/k2g_evm_defconfig
index 8a0703969665..8331866580d0 100644
--- a/configs/k2g_evm_defconfig
+++ b/configs/k2g_evm_defconfig
@@ -44,7 +44,6 @@ CONFIG_NAND=y
CONFIG_NAND_DAVINCI=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
diff --git a/configs/k2g_hs_evm_defconfig b/configs/k2g_hs_evm_defconfig
index 5f91f11d3621..19dccfd31cd5 100644
--- a/configs/k2g_hs_evm_defconfig
+++ b/configs/k2g_hs_evm_defconfig
@@ -37,7 +37,6 @@ CONFIG_NAND=y
CONFIG_NAND_DAVINCI=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
diff --git a/configs/koelsch_defconfig b/configs/koelsch_defconfig
index dbacfd87ba5d..1ff14ac4abd0 100644
--- a/configs/koelsch_defconfig
+++ b/configs/koelsch_defconfig
@@ -64,7 +64,6 @@ CONFIG_RENESAS_SDHI=y
CONFIG_MTD=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHY_MICREL=y
diff --git a/configs/lager_defconfig b/configs/lager_defconfig
index 242e104b6bd3..d924d76911de 100644
--- a/configs/lager_defconfig
+++ b/configs/lager_defconfig
@@ -66,7 +66,6 @@ CONFIG_RENESAS_SDHI=y
CONFIG_MTD=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHY_MICREL=y
diff --git a/configs/maxbcm_defconfig b/configs/maxbcm_defconfig
index a4d2fcd2596a..5c716cdec8b8 100644
--- a/configs/maxbcm_defconfig
+++ b/configs/maxbcm_defconfig
@@ -33,7 +33,6 @@ CONFIG_DEFAULT_DEVICE_TREE="armada-xp-maxbcm"
CONFIG_SPL_OF_TRANSLATE=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/mt7629_rfb_defconfig b/configs/mt7629_rfb_defconfig
index 1729d13c3d38..e390d8cc0b22 100644
--- a/configs/mt7629_rfb_defconfig
+++ b/configs/mt7629_rfb_defconfig
@@ -43,7 +43,6 @@ CONFIG_DM_GPIO=y
# CONFIG_MMC is not set
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_EON=y
CONFIG_SPI_FLASH_GIGADEVICE=y
CONFIG_SPI_FLASH_ISSI=y
diff --git a/configs/mx6sxsabreauto_defconfig b/configs/mx6sxsabreauto_defconfig
index 41fac12d0c91..1f3dc837890a 100644
--- a/configs/mx6sxsabreauto_defconfig
+++ b/configs/mx6sxsabreauto_defconfig
@@ -38,7 +38,6 @@ CONFIG_NAND=y
CONFIG_NAND_MXS=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
CONFIG_MII=y
diff --git a/configs/mx6sxsabresd_defconfig b/configs/mx6sxsabresd_defconfig
index d04ec4f9a34a..6ad293907109 100644
--- a/configs/mx6sxsabresd_defconfig
+++ b/configs/mx6sxsabresd_defconfig
@@ -40,7 +40,6 @@ CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
diff --git a/configs/mx6ul_14x14_evk_defconfig b/configs/mx6ul_14x14_evk_defconfig
index 607045f8570d..12b51c777d83 100644
--- a/configs/mx6ul_14x14_evk_defconfig
+++ b/configs/mx6ul_14x14_evk_defconfig
@@ -45,7 +45,6 @@ CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
diff --git a/configs/mx6ul_9x9_evk_defconfig b/configs/mx6ul_9x9_evk_defconfig
index 2c8be5fb31ef..dad9e5a1da14 100644
--- a/configs/mx6ul_9x9_evk_defconfig
+++ b/configs/mx6ul_9x9_evk_defconfig
@@ -45,7 +45,6 @@ CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
diff --git a/configs/mx6ull_14x14_evk_defconfig b/configs/mx6ull_14x14_evk_defconfig
index 0b7dcd63a944..e4076927c41e 100644
--- a/configs/mx6ull_14x14_evk_defconfig
+++ b/configs/mx6ull_14x14_evk_defconfig
@@ -32,7 +32,6 @@ CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
diff --git a/configs/mx6ull_14x14_evk_plugin_defconfig b/configs/mx6ull_14x14_evk_plugin_defconfig
index 6fee83d020d1..aae81e2772c4 100644
--- a/configs/mx6ull_14x14_evk_plugin_defconfig
+++ b/configs/mx6ull_14x14_evk_plugin_defconfig
@@ -33,7 +33,6 @@ CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
diff --git a/configs/mx7dsabresd_qspi_defconfig b/configs/mx7dsabresd_qspi_defconfig
index 48f4068e8cd0..3ef95851d761 100644
--- a/configs/mx7dsabresd_qspi_defconfig
+++ b/configs/mx7dsabresd_qspi_defconfig
@@ -49,7 +49,6 @@ CONFIG_MMC_HS200_SUPPORT=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_EON=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_PHYLIB=y
diff --git a/configs/porter_defconfig b/configs/porter_defconfig
index 6fa750a03a7d..057d9bcd6d2b 100644
--- a/configs/porter_defconfig
+++ b/configs/porter_defconfig
@@ -65,7 +65,6 @@ CONFIG_RENESAS_SDHI=y
CONFIG_MTD=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHY_MICREL=y
diff --git a/configs/r8a77970_eagle_defconfig b/configs/r8a77970_eagle_defconfig
index 5af1bdb221f6..d269c62101e3 100644
--- a/configs/r8a77970_eagle_defconfig
+++ b/configs/r8a77970_eagle_defconfig
@@ -43,7 +43,6 @@ CONFIG_SYS_I2C_RCAR_IIC=y
# CONFIG_MMC is not set
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_PHY_MICREL=y
diff --git a/configs/silk_defconfig b/configs/silk_defconfig
index 3350e6903960..3cb4f6e005ae 100644
--- a/configs/silk_defconfig
+++ b/configs/silk_defconfig
@@ -66,7 +66,6 @@ CONFIG_RENESAS_SDHI=y
CONFIG_MTD=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHY_MICREL=y
diff --git a/configs/socfpga_arria5_defconfig b/configs/socfpga_arria5_defconfig
index e7e1121c5c42..02e329a70417 100644
--- a/configs/socfpga_arria5_defconfig
+++ b/configs/socfpga_arria5_defconfig
@@ -51,7 +51,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_DW=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
diff --git a/configs/socfpga_cyclone5_defconfig b/configs/socfpga_cyclone5_defconfig
index 8989c4dc96ce..13dc508631e9 100644
--- a/configs/socfpga_cyclone5_defconfig
+++ b/configs/socfpga_cyclone5_defconfig
@@ -51,7 +51,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_DW=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/socfpga_is1_defconfig b/configs/socfpga_is1_defconfig
index 682e58fdb8b8..cd7211d202ba 100644
--- a/configs/socfpga_is1_defconfig
+++ b/configs/socfpga_is1_defconfig
@@ -48,7 +48,6 @@ CONFIG_SYS_I2C_DW=y
# CONFIG_MMC is not set
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
diff --git a/configs/socfpga_sockit_defconfig b/configs/socfpga_sockit_defconfig
index 66f7733ee86a..c2c3c9eec4ab 100644
--- a/configs/socfpga_sockit_defconfig
+++ b/configs/socfpga_sockit_defconfig
@@ -51,7 +51,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_DW=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/socfpga_socrates_defconfig b/configs/socfpga_socrates_defconfig
index 05f38cbcd22f..0fc76152a315 100644
--- a/configs/socfpga_socrates_defconfig
+++ b/configs/socfpga_socrates_defconfig
@@ -52,7 +52,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_DW=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/socfpga_sr1500_defconfig b/configs/socfpga_sr1500_defconfig
index 97366cdfff0c..d984047bfe63 100644
--- a/configs/socfpga_sr1500_defconfig
+++ b/configs/socfpga_sr1500_defconfig
@@ -53,7 +53,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_DW=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_PHY_MARVELL=y
diff --git a/configs/socfpga_stratix10_defconfig b/configs/socfpga_stratix10_defconfig
index 5f3d733a8bc2..8550acb9ba2b 100644
--- a/configs/socfpga_stratix10_defconfig
+++ b/configs/socfpga_stratix10_defconfig
@@ -39,7 +39,6 @@ CONFIG_SYS_I2C_DW=y
CONFIG_DM_MMC=y
CONFIG_MMC_DW=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
diff --git a/configs/stout_defconfig b/configs/stout_defconfig
index d99d97b60b2f..5c4261824342 100644
--- a/configs/stout_defconfig
+++ b/configs/stout_defconfig
@@ -65,7 +65,6 @@ CONFIG_RENESAS_SDHI=y
CONFIG_MTD=y
CONFIG_MTD_DEVICE=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHY_MICREL=y
diff --git a/configs/topic_miami_defconfig b/configs/topic_miami_defconfig
index 6bdfd63c8ee0..407c3bdaa3de 100644
--- a/configs/topic_miami_defconfig
+++ b/configs/topic_miami_defconfig
@@ -40,7 +40,6 @@ CONFIG_ZYNQ_I2C1=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_DEBUG_UART_ZYNQ=y
diff --git a/configs/topic_miamilite_defconfig b/configs/topic_miamilite_defconfig
index a2ff87a55029..8e912d8586d2 100644
--- a/configs/topic_miamilite_defconfig
+++ b/configs/topic_miamilite_defconfig
@@ -40,7 +40,6 @@ CONFIG_ZYNQ_I2C1=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_DEBUG_UART_ZYNQ=y
diff --git a/configs/topic_miamiplus_defconfig b/configs/topic_miamiplus_defconfig
index 74deff0a19c8..371b2ad91571 100644
--- a/configs/topic_miamiplus_defconfig
+++ b/configs/topic_miamiplus_defconfig
@@ -39,7 +39,6 @@ CONFIG_ZYNQ_I2C1=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
# CONFIG_NETDEVICES is not set
diff --git a/configs/xilinx_versal_virt_defconfig b/configs/xilinx_versal_virt_defconfig
index 668c313a2914..c56b504bef7c 100644
--- a/configs/xilinx_versal_virt_defconfig
+++ b/configs/xilinx_versal_virt_defconfig
@@ -47,7 +47,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_mini_qspi_defconfig b/configs/xilinx_zynqmp_mini_qspi_defconfig
index 1138faffcc39..9f2a2f59f6ea 100644
--- a/configs/xilinx_zynqmp_mini_qspi_defconfig
+++ b/configs/xilinx_zynqmp_mini_qspi_defconfig
@@ -55,7 +55,6 @@ CONFIG_SPL_DM_SEQ_ALIAS=y
# CONFIG_MMC is not set
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zc1232_revA_defconfig b/configs/xilinx_zynqmp_zc1232_revA_defconfig
index 4700956dd2db..06247a0628fb 100644
--- a/configs/xilinx_zynqmp_zc1232_revA_defconfig
+++ b/configs/xilinx_zynqmp_zc1232_revA_defconfig
@@ -37,7 +37,6 @@ CONFIG_FPGA_ZYNQMPPL=y
CONFIG_MISC=y
CONFIG_DM_MMC=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zc1254_revA_defconfig b/configs/xilinx_zynqmp_zc1254_revA_defconfig
index 0570414a0532..5bc1aaba696b 100644
--- a/configs/xilinx_zynqmp_zc1254_revA_defconfig
+++ b/configs/xilinx_zynqmp_zc1254_revA_defconfig
@@ -37,7 +37,6 @@ CONFIG_FPGA_ZYNQMPPL=y
CONFIG_MISC=y
CONFIG_DM_MMC=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zc1275_revA_defconfig b/configs/xilinx_zynqmp_zc1275_revA_defconfig
index 7c83f7036814..d0b0a19caf93 100644
--- a/configs/xilinx_zynqmp_zc1275_revA_defconfig
+++ b/configs/xilinx_zynqmp_zc1275_revA_defconfig
@@ -37,7 +37,6 @@ CONFIG_FPGA_ZYNQMPPL=y
CONFIG_MISC=y
CONFIG_DM_MMC=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zc1275_revB_defconfig b/configs/xilinx_zynqmp_zc1275_revB_defconfig
index e2aade7606bf..6bc3b6af9a67 100644
--- a/configs/xilinx_zynqmp_zc1275_revB_defconfig
+++ b/configs/xilinx_zynqmp_zc1275_revB_defconfig
@@ -40,7 +40,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig b/configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig
index ec26dd70fd57..536cfc98f115 100644
--- a/configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig
+++ b/configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig
@@ -61,7 +61,6 @@ CONFIG_MMC_HS200_SUPPORT=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zc1751_xm016_dc2_defconfig b/configs/xilinx_zynqmp_zc1751_xm016_dc2_defconfig
index c2b3d189ec4d..213f4c9cbfe4 100644
--- a/configs/xilinx_zynqmp_zc1751_xm016_dc2_defconfig
+++ b/configs/xilinx_zynqmp_zc1751_xm016_dc2_defconfig
@@ -58,7 +58,6 @@ CONFIG_MTD_DEVICE=y
CONFIG_NAND=y
CONFIG_NAND_ARASAN=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SST=y
CONFIG_PHY_MARVELL=y
CONFIG_PHY_NATSEMI=y
diff --git a/configs/xilinx_zynqmp_zc1751_xm018_dc4_defconfig b/configs/xilinx_zynqmp_zc1751_xm018_dc4_defconfig
index a0bbc0fbde8b..6e31550e601c 100644
--- a/configs/xilinx_zynqmp_zc1751_xm018_dc4_defconfig
+++ b/configs/xilinx_zynqmp_zc1751_xm018_dc4_defconfig
@@ -47,7 +47,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zcu100_revC_defconfig b/configs/xilinx_zynqmp_zcu100_revC_defconfig
index 429bfd4fd3dd..23d2ca58c1b7 100644
--- a/configs/xilinx_zynqmp_zcu100_revC_defconfig
+++ b/configs/xilinx_zynqmp_zcu100_revC_defconfig
@@ -60,7 +60,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zcu102_rev1_0_defconfig b/configs/xilinx_zynqmp_zcu102_rev1_0_defconfig
index e41366ecf7d0..4a7ad87f4093 100644
--- a/configs/xilinx_zynqmp_zcu102_rev1_0_defconfig
+++ b/configs/xilinx_zynqmp_zcu102_rev1_0_defconfig
@@ -75,7 +75,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zcu102_revA_defconfig b/configs/xilinx_zynqmp_zcu102_revA_defconfig
index 41a03371d514..aa2adbd19313 100644
--- a/configs/xilinx_zynqmp_zcu102_revA_defconfig
+++ b/configs/xilinx_zynqmp_zcu102_revA_defconfig
@@ -72,7 +72,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zcu102_revB_defconfig b/configs/xilinx_zynqmp_zcu102_revB_defconfig
index 78deb6a967f2..17903a1e29d2 100644
--- a/configs/xilinx_zynqmp_zcu102_revB_defconfig
+++ b/configs/xilinx_zynqmp_zcu102_revB_defconfig
@@ -72,7 +72,6 @@ CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zcu104_revA_defconfig b/configs/xilinx_zynqmp_zcu104_revA_defconfig
index b612ce213224..28e18ae1252e 100644
--- a/configs/xilinx_zynqmp_zcu104_revA_defconfig
+++ b/configs/xilinx_zynqmp_zcu104_revA_defconfig
@@ -57,7 +57,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zcu104_revC_defconfig b/configs/xilinx_zynqmp_zcu104_revC_defconfig
index 2fb66b2177ab..3ddd63181603 100644
--- a/configs/xilinx_zynqmp_zcu104_revC_defconfig
+++ b/configs/xilinx_zynqmp_zcu104_revC_defconfig
@@ -58,7 +58,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zcu106_revA_defconfig b/configs/xilinx_zynqmp_zcu106_revA_defconfig
index 20e210ec3822..a6da8976317c 100644
--- a/configs/xilinx_zynqmp_zcu106_revA_defconfig
+++ b/configs/xilinx_zynqmp_zcu106_revA_defconfig
@@ -66,7 +66,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/xilinx_zynqmp_zcu111_revA_defconfig b/configs/xilinx_zynqmp_zcu111_revA_defconfig
index 8bace6d80883..f5dcceb6ae30 100644
--- a/configs/xilinx_zynqmp_zcu111_revA_defconfig
+++ b/configs/xilinx_zynqmp_zcu111_revA_defconfig
@@ -60,7 +60,6 @@ CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/zynq_cc108_defconfig b/configs/zynq_cc108_defconfig
index c06e546e0a2c..48bd2523e25f 100644
--- a/configs/zynq_cc108_defconfig
+++ b/configs/zynq_cc108_defconfig
@@ -34,7 +34,6 @@ CONFIG_DM_GPIO=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_ISSI=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
diff --git a/configs/zynq_cse_qspi_defconfig b/configs/zynq_cse_qspi_defconfig
index 2aee069bb188..d78a842e6a79 100644
--- a/configs/zynq_cse_qspi_defconfig
+++ b/configs/zynq_cse_qspi_defconfig
@@ -57,7 +57,6 @@ CONFIG_DEFAULT_DEVICE_TREE="zynq-cse-qspi-single"
CONFIG_SPL_DM_SEQ_ALIAS=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_ISSI=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
diff --git a/configs/zynq_dlc20_rev1_0_defconfig b/configs/zynq_dlc20_rev1_0_defconfig
index 4b9fdfe186c8..1acfad8486ac 100644
--- a/configs/zynq_dlc20_rev1_0_defconfig
+++ b/configs/zynq_dlc20_rev1_0_defconfig
@@ -50,7 +50,6 @@ CONFIG_ZYNQ_I2C0=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_PHY_REALTEK=y
diff --git a/configs/zynq_microzed_defconfig b/configs/zynq_microzed_defconfig
index 29b8594d8bc1..d705be077e36 100644
--- a/configs/zynq_microzed_defconfig
+++ b/configs/zynq_microzed_defconfig
@@ -40,7 +40,6 @@ CONFIG_DM_GPIO=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_WINBOND=y
diff --git a/configs/zynq_minized_defconfig b/configs/zynq_minized_defconfig
index 8597c41ca03c..cdf31330a29d 100644
--- a/configs/zynq_minized_defconfig
+++ b/configs/zynq_minized_defconfig
@@ -41,7 +41,6 @@ CONFIG_DM_GPIO=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_WINBOND=y
diff --git a/configs/zynq_z_turn_defconfig b/configs/zynq_z_turn_defconfig
index e40afaacf865..830c9ef067b0 100644
--- a/configs/zynq_z_turn_defconfig
+++ b/configs/zynq_z_turn_defconfig
@@ -40,7 +40,6 @@ CONFIG_LED_GPIO=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_WINBOND=y
diff --git a/configs/zynq_zc702_defconfig b/configs/zynq_zc702_defconfig
index 27e6bd1e0e8b..1ae867d72503 100644
--- a/configs/zynq_zc702_defconfig
+++ b/configs/zynq_zc702_defconfig
@@ -52,7 +52,6 @@ CONFIG_LED_GPIO=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_ISSI=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
diff --git a/configs/zynq_zc706_defconfig b/configs/zynq_zc706_defconfig
index bcbfa65e41b1..5ac94326f718 100644
--- a/configs/zynq_zc706_defconfig
+++ b/configs/zynq_zc706_defconfig
@@ -52,7 +52,6 @@ CONFIG_ZYNQ_I2C0=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_ISSI=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
diff --git a/configs/zynq_zc770_xm010_defconfig b/configs/zynq_zc770_xm010_defconfig
index fed1502d1b6b..22d5b847668c 100644
--- a/configs/zynq_zc770_xm010_defconfig
+++ b/configs/zynq_zc770_xm010_defconfig
@@ -41,7 +41,6 @@ CONFIG_DM_GPIO=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_ISSI=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
diff --git a/configs/zynq_zc770_xm013_defconfig b/configs/zynq_zc770_xm013_defconfig
index a08bd2993385..dcadaf21316b 100644
--- a/configs/zynq_zc770_xm013_defconfig
+++ b/configs/zynq_zc770_xm013_defconfig
@@ -35,7 +35,6 @@ CONFIG_FPGA_ZYNQPL=y
CONFIG_DM_GPIO=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_ISSI=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
diff --git a/configs/zynq_zed_defconfig b/configs/zynq_zed_defconfig
index c583c5c83b92..eaaf0a09b912 100644
--- a/configs/zynq_zed_defconfig
+++ b/configs/zynq_zed_defconfig
@@ -43,7 +43,6 @@ CONFIG_DM_GPIO=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_WINBOND=y
diff --git a/configs/zynq_zybo_defconfig b/configs/zynq_zybo_defconfig
index 82931713a2ce..300cf05456a6 100644
--- a/configs/zynq_zybo_defconfig
+++ b/configs/zynq_zybo_defconfig
@@ -50,7 +50,6 @@ CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET=0xFA
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_PHY_MARVELL=y
CONFIG_PHY_REALTEK=y
diff --git a/configs/zynq_zybo_z7_defconfig b/configs/zynq_zybo_z7_defconfig
index 190759fe8b0e..3670b1998dc7 100644
--- a/configs/zynq_zybo_z7_defconfig
+++ b/configs/zynq_zybo_z7_defconfig
@@ -47,7 +47,6 @@ CONFIG_ZYNQ_I2C1=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_PHY_REALTEK=y
CONFIG_MII=y
diff --git a/doc/SPI/README.ti_qspi_dra_test b/doc/SPI/README.ti_qspi_dra_test
index fe378572369b..e89f53587fa7 100644
--- a/doc/SPI/README.ti_qspi_dra_test
+++ b/doc/SPI/README.ti_qspi_dra_test
@@ -22,7 +22,6 @@ Commands to erase/write u-boot/mlo to flash device
--------------------------------------------------
U-Boot# sf probe 0
SF: Detected S25FL256S_64K with page size 256 Bytes, erase size 64 KiB, total 32 MiB, mapped at 5c000000
-SF: Warning - Only lower 16MiB accessible, Full access #define CONFIG_SPI_FLASH_BAR
U-Boot# sf erase 0 0x10000
SF: 65536 bytes @ 0x0 Erased: OK
U-Boot# sf erase 0x20000 0x10000
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 5ee855fc5319..43b3f68fee10 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -111,6 +111,7 @@ config FSL_DSPI
config ICH_SPI
bool "Intel ICH SPI driver"
+ imply SPI_FLASH_BAR
help
Enable the Intel ICH SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Intel
@@ -140,6 +141,7 @@ config MT7621_SPI
config MTK_QSPI
bool "Mediatek QSPI driver"
+ imply SPI_FLASH_BAR
help
Enable the Mediatek QSPI driver. This driver can be
used to access the SPI NOR flash on platforms embedding this
@@ -172,6 +174,7 @@ config PL022_SPI
config RENESAS_RPC_SPI
bool "Renesas RPC SPI driver"
depends on RCAR_GEN3
+ imply SPI_FLASH_BAR
help
Enable the Renesas RPC SPI driver, used to access SPI NOR flash
on Renesas RCar Gen3 SoCs. This uses driver model and requires a
@@ -213,6 +216,7 @@ config SANDBOX_SPI
config STM32_QSPI
bool "STM32F7 QSPI driver"
depends on STM32F7
+ imply SPI_FLASH_BAR
help
Enable the STM32F7 Quad-SPI (QSPI) driver. This driver can be
used to access the SPI NOR flash chips on platforms embedding
@@ -309,6 +313,7 @@ config FSL_ESPI
config FSL_QSPI
bool "Freescale QSPI driver"
+ imply SPI_FLASH_BAR
help
Enable the Freescale Quad-SPI (QSPI) driver. This driver can be
used to access the SPI NOR flash on platforms embedding this
diff --git a/include/configs/T102xQDS.h b/include/configs/T102xQDS.h
index f3b0fe0144ff..c63dfd318680 100644
--- a/include/configs/T102xQDS.h
+++ b/include/configs/T102xQDS.h
@@ -501,7 +501,6 @@ unsigned long get_board_ddr_clk(void);
/*
* eSPI - Enhanced SPI
*/
-#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
diff --git a/include/configs/T102xRDB.h b/include/configs/T102xRDB.h
index 673d1112e22a..c72be9fb387a 100644
--- a/include/configs/T102xRDB.h
+++ b/include/configs/T102xRDB.h
@@ -498,7 +498,6 @@ unsigned long get_board_ddr_clk(void);
/*
* eSPI - Enhanced SPI
*/
-#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h
index 7375d6ff4607..4cecab3401e9 100644
--- a/include/configs/T104xRDB.h
+++ b/include/configs/T104xRDB.h
@@ -521,7 +521,6 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
/*
* eSPI - Enhanced SPI
*/
-#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
#define CONFIG_ENV_SPI_BUS 0
diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h
index 1dcf2779d755..69ec109831a0 100644
--- a/include/configs/T208xQDS.h
+++ b/include/configs/T208xQDS.h
@@ -497,7 +497,6 @@ unsigned long get_board_ddr_clk(void);
*/
#ifdef CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
#endif
diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h
index ddb60b3d6d94..1d6a390b72df 100644
--- a/include/configs/T208xRDB.h
+++ b/include/configs/T208xRDB.h
@@ -437,7 +437,6 @@ unsigned long get_board_ddr_clk(void);
* eSPI - Enhanced SPI
*/
#ifdef CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
#endif
diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h
index 6cafdc66859b..6e23fa29b33b 100644
--- a/include/configs/gw_ventana.h
+++ b/include/configs/gw_ventana.h
@@ -52,7 +52,6 @@
/* SPI */
#ifdef CONFIG_CMD_SF
#define CONFIG_SPI_FLASH_MTD
- #define CONFIG_SPI_FLASH_BAR
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
/* GPIO 3-19 (21248) */
diff --git a/include/configs/km/kmp204x-common.h b/include/configs/km/kmp204x-common.h
index a8f7300c1eb2..c762c93ac0aa 100644
--- a/include/configs/km/kmp204x-common.h
+++ b/include/configs/km/kmp204x-common.h
@@ -253,7 +253,6 @@ int get_scl(void);
/*
* eSPI - Enhanced SPI
*/
-#define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE 0
diff --git a/include/configs/ls1021aiot.h b/include/configs/ls1021aiot.h
index 10dc0c68435b..6be8df109bd6 100644
--- a/include/configs/ls1021aiot.h
+++ b/include/configs/ls1021aiot.h
@@ -135,7 +135,6 @@
#define QSPI0_AMBA_BASE 0x40000000
#define FSL_QSPI_FLASH_SIZE (1 << 24)
#define FSL_QSPI_FLASH_NUM 2
-#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SPI_FLASH_SPANSION
#endif
--
2.20.1
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 11/11] MAINTAINERS: Add an entry for SPI NOR
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (9 preceding siblings ...)
2018-12-21 6:38 ` [U-Boot] [PATCH v2 10/11] configs: Don't use SPI_FLASH_BAR as default Vignesh R
@ 2018-12-21 6:38 ` Vignesh R
2018-12-21 7:26 ` [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Stefan Roese
` (3 subsequent siblings)
14 siblings, 0 replies; 33+ messages in thread
From: Vignesh R @ 2018-12-21 6:38 UTC (permalink / raw)
To: u-boot
Add myself as co-maintainer for U-Boot SPI NOR subsystem.
Signed-off-by: Vignesh R <vigneshr@ti.com>
---
MAINTAINERS | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 0fb089807c57..a6d2b6e1bd5a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -634,6 +634,15 @@ F: drivers/mtd/spi/
F: drivers/spi/
F: include/spi*
+SPI-NOR
+M: Jagan Teki <jagan@openedev.com>
+M: Vignesh R <vigneshr@ti.com>
+S: Maintained
+F: drivers/mtd/spi/
+F: include/spi_flash.h
+F: include/linux/mtd/cfi.h
+F: include/linux/mtd/spi-nor.h
+
SPMI
M: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
S: Maintained
--
2.20.1
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (10 preceding siblings ...)
2018-12-21 6:38 ` [U-Boot] [PATCH v2 11/11] MAINTAINERS: Add an entry for SPI NOR Vignesh R
@ 2018-12-21 7:26 ` Stefan Roese
2018-12-21 10:33 ` Simon Goldschmidt
` (2 subsequent siblings)
14 siblings, 0 replies; 33+ messages in thread
From: Stefan Roese @ 2018-12-21 7:26 UTC (permalink / raw)
To: u-boot
Hi Vignesh,
On 21.12.18 07:38, Vignesh R wrote:
> U-Boot SPI NOR support (sf layer) is quite outdated as it does not
> support 4 byte addressing opcodes, SFDP table parsing and different types of
> quad mode enable sequences. Many newer flashes no longer support BANK
> registers used by sf layer to a access >16MB space.
> Also, many SPI controllers have special MMIO interfaces which provide
> accelerated read/write access but require knowledge of flash parameters
> to make use of it. Recent spi-mem layer provides a way to support such
> flashes but sf layer isn't using that.
> This patch series syncs SPI NOR framework from Linux v4.19. It also adds
> spi-mem support on top.
> So, we gain 4byte addressing support and SFDP support. This makes
> migrating to U-Boot MTD framework easier.
>
> Tested with few Spansion, micron and macronix flashes with TI's dra7xx,
> k2g, am43xx EVMs. I dont have access to flashes from other vendors. So,
> I would greatly appreciate testing on other platforms. Complete series
> with dependencies here[1]
>
> For clean build on some platforms, depends on CONFIG_SPI_FLASH migration
> to defconfigs [2]
>
> [1] https://github.com/r-vignesh/u-boot.git branch: spi-nor-mig-patch-v2
> [2] https://patchwork.ozlabs.org/patch/1007485/
>
> Simon, Stefan, Thanks for testing previous versions.
> I haven't carried Tested-by's here as I have added back SPI_FLASH_BAR
> support (but isn't enabled by default). Would be great if you could
> retest this series.
> I am hoping there won't be any major rework/changes after this round.
I just tested this new patchset on my LinkIt Smart 7688 board with the
4-byte strapped SPI NOR mx25l25635e device and it works without any
issues. So feel free to add my T-b tag to this series:
Tested-by: Stefan Roese <sr@denx.de>
Thanks,
Stefan
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (11 preceding siblings ...)
2018-12-21 7:26 ` [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Stefan Roese
@ 2018-12-21 10:33 ` Simon Goldschmidt
2018-12-21 11:11 ` Vignesh R
2019-01-14 15:02 ` Vignesh R
2019-01-21 17:14 ` Horatiu Vultur
14 siblings, 1 reply; 33+ messages in thread
From: Simon Goldschmidt @ 2018-12-21 10:33 UTC (permalink / raw)
To: u-boot
Am Fr., 21. Dez. 2018, 07:37 hat Vignesh R <vigneshr@ti.com> geschrieben:
> U-Boot SPI NOR support (sf layer) is quite outdated as it does not
> support 4 byte addressing opcodes, SFDP table parsing and different types
> of
> quad mode enable sequences. Many newer flashes no longer support BANK
> registers used by sf layer to a access >16MB space.
> Also, many SPI controllers have special MMIO interfaces which provide
> accelerated read/write access but require knowledge of flash parameters
> to make use of it. Recent spi-mem layer provides a way to support such
> flashes but sf layer isn't using that.
> This patch series syncs SPI NOR framework from Linux v4.19. It also adds
> spi-mem support on top.
> So, we gain 4byte addressing support and SFDP support. This makes
> migrating to U-Boot MTD framework easier.
>
> Tested with few Spansion, micron and macronix flashes with TI's dra7xx,
> k2g, am43xx EVMs. I dont have access to flashes from other vendors. So,
> I would greatly appreciate testing on other platforms. Complete series
> with dependencies here[1]
>
> For clean build on some platforms, depends on CONFIG_SPI_FLASH migration
> to defconfigs [2]
>
> [1] https://github.com/r-vignesh/u-boot.git branch: spi-nor-mig-patch-v2
> [2] https://patchwork.ozlabs.org/patch/1007485/
>
> Simon, Stefan, Thanks for testing previous versions.
> I haven't carried Tested-by's here as I have added back SPI_FLASH_BAR
> support (but isn't enabled by default). Would be great if you could
> retest this series.
> I am hoping there won't be any major rework/changes after this round.
>
Hi Vignesh,
I just did a quick test on this but it fails to boot. I guess this could be
a size problem. Unfortunately, the socfpga gen5 config does not correctly
check SPL size currently. I'll have to work on that. I'll test your patch
with a more limited config when I find the time.
Regards,
Simon
> Change log:
> Since v1:
> Remove #ifindef __UBOOT__
> Add back BAR support, but dont enable as default for all platform (see
> 10/11 for more details)
> Enable SPI_FLASH_TINY on boards where there is SPL size constraint as
> seen on travis ci builds.
> Drop sf_mtd changes for now as it seems to cause issues.
> v1: https://patchwork.ozlabs.org/cover/1012146/
>
> Since RFC v2:
> Fix issues reported by Simon Goldschmidt wrt 4 use of byte addressing
> opcode
> Fix issues in compiling SFDP code
> Re organize file names and Makefile to simply spi-nor-tiny inclusion
> Remove SPI_FLASH_BAR and SF_DUAL_FLASH as these are no longer used
> RFC v2: https://patchwork.ozlabs.org/cover/1007589/
>
> Since RFC v1:
> Add lightweight SPI flash stack for boards with SPL size constraints
> Provide non DM version of spi-mem
> Fix build issues on different platforms as reported by travis-ci on v1
>
> RFC v1: https://patchwork.ozlabs.org/cover/1004689/
>
> Vignesh R (11):
> spi-mem: Claim SPI bus before spi mem access
> spi: Add non DM version of SPI_MEM
> sh: bitops: add hweight*() macros
> mtd: spi: Port SPI NOR framework from Linux
> mtd: spi: Switch to new SPI NOR framework
> mtd: spi: Remove unused files
> mtd: spi: Add lightweight SPI flash stack for SPL
> configs: Enable SPI_FLASH_TINY for resource constrained boards
> configs: Remove SF_DUAL_FLASH
> configs: Don't use SPI_FLASH_BAR as default
> MAINTAINERS: Add an entry for SPI NOR
>
> MAINTAINERS | 9 +
> arch/arm/mach-omap2/am33xx/Kconfig | 1 -
> arch/sh/include/asm/bitops.h | 4 +
> common/spl/Kconfig | 21 +-
> configs/alt_defconfig | 1 -
> configs/am57xx_evm_defconfig | 1 -
> configs/am57xx_hs_evm_defconfig | 1 -
> configs/ap121_defconfig | 1 -
> configs/ap143_defconfig | 1 -
> configs/avnet_ultra96_rev1_defconfig | 1 -
> configs/axm_defconfig | 1 +
> configs/axs101_defconfig | 1 -
> configs/axs103_defconfig | 1 -
> configs/bg0900_defconfig | 1 -
> configs/blanche_defconfig | 1 -
> configs/cl-som-am57x_defconfig | 1 -
> configs/clearfog_defconfig | 1 -
> configs/cm_t43_defconfig | 1 -
> configs/da850_am18xxevm_defconfig | 1 +
> configs/da850evm_nand_defconfig | 2 +-
> configs/db-88f6820-amc_defconfig | 1 -
> configs/db-88f6820-gp_defconfig | 1 +
> configs/display5_defconfig | 1 -
> configs/display5_factory_defconfig | 1 -
> configs/dra7xx_evm_defconfig | 1 -
> configs/dra7xx_hs_evm_defconfig | 1 -
> configs/ds109_defconfig | 1 -
> configs/ds414_defconfig | 1 -
> configs/evb-rv1108_defconfig | 1 -
> configs/gose_defconfig | 1 -
> configs/helios4_defconfig | 1 -
> configs/k2g_evm_defconfig | 1 -
> configs/k2g_hs_evm_defconfig | 1 -
> configs/koelsch_defconfig | 1 -
> configs/lager_defconfig | 1 -
> configs/maxbcm_defconfig | 1 -
> configs/mt7629_rfb_defconfig | 1 -
> configs/mx6sxsabreauto_defconfig | 1 -
> configs/mx6sxsabresd_defconfig | 1 -
> configs/mx6ul_14x14_evk_defconfig | 1 -
> configs/mx6ul_9x9_evk_defconfig | 1 -
> configs/mx6ull_14x14_evk_defconfig | 1 -
> configs/mx6ull_14x14_evk_plugin_defconfig | 1 -
> configs/mx7dsabresd_qspi_defconfig | 1 -
> configs/porter_defconfig | 2 +-
> configs/r8a77970_eagle_defconfig | 1 -
> configs/silk_defconfig | 1 -
> configs/socfpga_arria5_defconfig | 1 -
> configs/socfpga_cyclone5_defconfig | 1 -
> configs/socfpga_is1_defconfig | 1 -
> configs/socfpga_sockit_defconfig | 1 -
> configs/socfpga_socrates_defconfig | 1 -
> configs/socfpga_sr1500_defconfig | 1 -
> configs/socfpga_stratix10_defconfig | 1 -
> configs/stout_defconfig | 2 +-
> configs/taurus_defconfig | 3 +-
> configs/topic_miami_defconfig | 1 -
> configs/topic_miamilite_defconfig | 2 -
> configs/topic_miamiplus_defconfig | 2 -
> configs/turris_omnia_defconfig | 2 +-
> configs/xilinx_versal_virt_defconfig | 1 -
> configs/xilinx_zynqmp_mini_qspi_defconfig | 2 -
> configs/xilinx_zynqmp_zc1232_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1254_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1275_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1275_revB_defconfig | 2 -
> .../xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 -
> .../xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 1 -
> .../xilinx_zynqmp_zc1751_xm018_dc4_defconfig | 1 -
> configs/xilinx_zynqmp_zcu100_revC_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_revA_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 -
> configs/xilinx_zynqmp_zcu104_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zcu104_revC_defconfig | 2 -
> configs/xilinx_zynqmp_zcu106_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zcu111_revA_defconfig | 1 -
> configs/zynq_cc108_defconfig | 1 -
> configs/zynq_cse_qspi_defconfig | 1 -
> configs/zynq_dlc20_rev1_0_defconfig | 1 -
> configs/zynq_microzed_defconfig | 1 -
> configs/zynq_minized_defconfig | 1 -
> configs/zynq_z_turn_defconfig | 1 -
> configs/zynq_zc702_defconfig | 1 -
> configs/zynq_zc706_defconfig | 1 -
> configs/zynq_zc770_xm010_defconfig | 1 -
> configs/zynq_zc770_xm013_defconfig | 1 -
> configs/zynq_zed_defconfig | 1 -
> configs/zynq_zybo_defconfig | 1 -
> configs/zynq_zybo_z7_defconfig | 1 -
> doc/SPI/README.dual-flash | 92 -
> doc/SPI/README.ti_qspi_dra_test | 1 -
> drivers/mtd/spi/Kconfig | 16 +-
> drivers/mtd/spi/Makefile | 12 +-
> drivers/mtd/spi/sandbox.c | 36 +-
> drivers/mtd/spi/sf_dataflash.c | 11 +-
> drivers/mtd/spi/sf_internal.h | 225 +-
> drivers/mtd/spi/sf_probe.c | 33 +-
> drivers/mtd/spi/spi-nor-core.c | 2432 +++++++++++++++++
> drivers/mtd/spi/spi-nor-ids.c | 297 ++
> drivers/mtd/spi/spi-nor-tiny.c | 810 ++++++
> drivers/mtd/spi/spi_flash.c | 1337 ---------
> drivers/mtd/spi/spi_flash_ids.c | 211 --
> drivers/spi/Kconfig | 9 +-
> drivers/spi/Makefile | 1 +
> drivers/spi/spi-mem-nodm.c | 89 +
> drivers/spi/spi-mem.c | 6 +
> drivers/spi/stm32_qspi.c | 4 +-
> include/configs/T102xQDS.h | 1 -
> include/configs/T102xRDB.h | 1 -
> include/configs/T104xRDB.h | 1 -
> include/configs/T208xQDS.h | 1 -
> include/configs/T208xRDB.h | 1 -
> include/configs/gw_ventana.h | 1 -
> include/configs/km/kmp204x-common.h | 1 -
> include/configs/ls1021aiot.h | 1 -
> include/configs/socfpga_stratix10_socdk.h | 1 -
> include/linux/mtd/cfi.h | 32 +
> include/linux/mtd/spi-nor.h | 419 +++
> include/spi_flash.h | 105 +-
> 120 files changed, 4266 insertions(+), 2058 deletions(-)
> delete mode 100644 doc/SPI/README.dual-flash
> create mode 100644 drivers/mtd/spi/spi-nor-core.c
> create mode 100644 drivers/mtd/spi/spi-nor-ids.c
> create mode 100644 drivers/mtd/spi/spi-nor-tiny.c
> delete mode 100644 drivers/mtd/spi/spi_flash.c
> delete mode 100644 drivers/mtd/spi/spi_flash_ids.c
> create mode 100644 drivers/spi/spi-mem-nodm.c
> create mode 100644 include/linux/mtd/cfi.h
> create mode 100644 include/linux/mtd/spi-nor.h
>
> --
> 2.20.1
>
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2018-12-21 10:33 ` Simon Goldschmidt
@ 2018-12-21 11:11 ` Vignesh R
2018-12-21 13:29 ` Simon Goldschmidt
0 siblings, 1 reply; 33+ messages in thread
From: Vignesh R @ 2018-12-21 11:11 UTC (permalink / raw)
To: u-boot
Hi Simon,
[...]
>
> Hi Vignesh,
>
> I just did a quick test on this but it fails to boot. I guess this could
> be a size problem.
I guess. SPL_SPI_FLASH_TINY would help with SPL size issue here.
> Unfortunately, the socfpga gen5 config does not
> correctly check SPL size currently. I'll have to work on that. I'll test
> your patch with a more limited config when I find the time.
>
Okay, thanks!
Regards
Vignesh
> Regards,
> Simon
>
>
> Change log:
> Since v1:
> Remove #ifindef __UBOOT__
> Add back BAR support, but dont enable as default for all platform (see
> 10/11 for more details)
> Enable SPI_FLASH_TINY on boards where there is SPL size constraint as
> seen on travis ci builds.
> Drop sf_mtd changes for now as it seems to cause issues.
> v1: https://patchwork.ozlabs.org/cover/1012146/
>
> Since RFC v2:
> Fix issues reported by Simon Goldschmidt wrt 4 use of byte
> addressing opcode
> Fix issues in compiling SFDP code
> Re organize file names and Makefile to simply spi-nor-tiny inclusion
> Remove SPI_FLASH_BAR and SF_DUAL_FLASH as these are no longer used
> RFC v2: https://patchwork.ozlabs.org/cover/1007589/
>
> Since RFC v1:
> Add lightweight SPI flash stack for boards with SPL size constraints
> Provide non DM version of spi-mem
> Fix build issues on different platforms as reported by travis-ci on v1
>
> RFC v1: https://patchwork.ozlabs.org/cover/1004689/
>
> Vignesh R (11):
> spi-mem: Claim SPI bus before spi mem access
> spi: Add non DM version of SPI_MEM
> sh: bitops: add hweight*() macros
> mtd: spi: Port SPI NOR framework from Linux
> mtd: spi: Switch to new SPI NOR framework
> mtd: spi: Remove unused files
> mtd: spi: Add lightweight SPI flash stack for SPL
> configs: Enable SPI_FLASH_TINY for resource constrained boards
> configs: Remove SF_DUAL_FLASH
> configs: Don't use SPI_FLASH_BAR as default
> MAINTAINERS: Add an entry for SPI NOR
>
> MAINTAINERS | 9 +
> arch/arm/mach-omap2/am33xx/Kconfig | 1 -
> arch/sh/include/asm/bitops.h | 4 +
> common/spl/Kconfig | 21 +-
> configs/alt_defconfig | 1 -
> configs/am57xx_evm_defconfig | 1 -
> configs/am57xx_hs_evm_defconfig | 1 -
> configs/ap121_defconfig | 1 -
> configs/ap143_defconfig | 1 -
> configs/avnet_ultra96_rev1_defconfig | 1 -
> configs/axm_defconfig | 1 +
> configs/axs101_defconfig | 1 -
> configs/axs103_defconfig | 1 -
> configs/bg0900_defconfig | 1 -
> configs/blanche_defconfig | 1 -
> configs/cl-som-am57x_defconfig | 1 -
> configs/clearfog_defconfig | 1 -
> configs/cm_t43_defconfig | 1 -
> configs/da850_am18xxevm_defconfig | 1 +
> configs/da850evm_nand_defconfig | 2 +-
> configs/db-88f6820-amc_defconfig | 1 -
> configs/db-88f6820-gp_defconfig | 1 +
> configs/display5_defconfig | 1 -
> configs/display5_factory_defconfig | 1 -
> configs/dra7xx_evm_defconfig | 1 -
> configs/dra7xx_hs_evm_defconfig | 1 -
> configs/ds109_defconfig | 1 -
> configs/ds414_defconfig | 1 -
> configs/evb-rv1108_defconfig | 1 -
> configs/gose_defconfig | 1 -
> configs/helios4_defconfig | 1 -
> configs/k2g_evm_defconfig | 1 -
> configs/k2g_hs_evm_defconfig | 1 -
> configs/koelsch_defconfig | 1 -
> configs/lager_defconfig | 1 -
> configs/maxbcm_defconfig | 1 -
> configs/mt7629_rfb_defconfig | 1 -
> configs/mx6sxsabreauto_defconfig | 1 -
> configs/mx6sxsabresd_defconfig | 1 -
> configs/mx6ul_14x14_evk_defconfig | 1 -
> configs/mx6ul_9x9_evk_defconfig | 1 -
> configs/mx6ull_14x14_evk_defconfig | 1 -
> configs/mx6ull_14x14_evk_plugin_defconfig | 1 -
> configs/mx7dsabresd_qspi_defconfig | 1 -
> configs/porter_defconfig | 2 +-
> configs/r8a77970_eagle_defconfig | 1 -
> configs/silk_defconfig | 1 -
> configs/socfpga_arria5_defconfig | 1 -
> configs/socfpga_cyclone5_defconfig | 1 -
> configs/socfpga_is1_defconfig | 1 -
> configs/socfpga_sockit_defconfig | 1 -
> configs/socfpga_socrates_defconfig | 1 -
> configs/socfpga_sr1500_defconfig | 1 -
> configs/socfpga_stratix10_defconfig | 1 -
> configs/stout_defconfig | 2 +-
> configs/taurus_defconfig | 3 +-
> configs/topic_miami_defconfig | 1 -
> configs/topic_miamilite_defconfig | 2 -
> configs/topic_miamiplus_defconfig | 2 -
> configs/turris_omnia_defconfig | 2 +-
> configs/xilinx_versal_virt_defconfig | 1 -
> configs/xilinx_zynqmp_mini_qspi_defconfig | 2 -
> configs/xilinx_zynqmp_zc1232_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1254_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1275_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1275_revB_defconfig | 2 -
> .../xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 -
> .../xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 1 -
> .../xilinx_zynqmp_zc1751_xm018_dc4_defconfig | 1 -
> configs/xilinx_zynqmp_zcu100_revC_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_revA_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 -
> configs/xilinx_zynqmp_zcu104_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zcu104_revC_defconfig | 2 -
> configs/xilinx_zynqmp_zcu106_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zcu111_revA_defconfig | 1 -
> configs/zynq_cc108_defconfig | 1 -
> configs/zynq_cse_qspi_defconfig | 1 -
> configs/zynq_dlc20_rev1_0_defconfig | 1 -
> configs/zynq_microzed_defconfig | 1 -
> configs/zynq_minized_defconfig | 1 -
> configs/zynq_z_turn_defconfig | 1 -
> configs/zynq_zc702_defconfig | 1 -
> configs/zynq_zc706_defconfig | 1 -
> configs/zynq_zc770_xm010_defconfig | 1 -
> configs/zynq_zc770_xm013_defconfig | 1 -
> configs/zynq_zed_defconfig | 1 -
> configs/zynq_zybo_defconfig | 1 -
> configs/zynq_zybo_z7_defconfig | 1 -
> doc/SPI/README.dual-flash | 92 -
> doc/SPI/README.ti_qspi_dra_test | 1 -
> drivers/mtd/spi/Kconfig | 16 +-
> drivers/mtd/spi/Makefile | 12 +-
> drivers/mtd/spi/sandbox.c | 36 +-
> drivers/mtd/spi/sf_dataflash.c | 11 +-
> drivers/mtd/spi/sf_internal.h | 225 +-
> drivers/mtd/spi/sf_probe.c | 33 +-
> drivers/mtd/spi/spi-nor-core.c | 2432 +++++++++++++++++
> drivers/mtd/spi/spi-nor-ids.c | 297 ++
> drivers/mtd/spi/spi-nor-tiny.c | 810 ++++++
> drivers/mtd/spi/spi_flash.c | 1337 ---------
> drivers/mtd/spi/spi_flash_ids.c | 211 --
> drivers/spi/Kconfig | 9 +-
> drivers/spi/Makefile | 1 +
> drivers/spi/spi-mem-nodm.c | 89 +
> drivers/spi/spi-mem.c | 6 +
> drivers/spi/stm32_qspi.c | 4 +-
> include/configs/T102xQDS.h | 1 -
> include/configs/T102xRDB.h | 1 -
> include/configs/T104xRDB.h | 1 -
> include/configs/T208xQDS.h | 1 -
> include/configs/T208xRDB.h | 1 -
> include/configs/gw_ventana.h | 1 -
> include/configs/km/kmp204x-common.h | 1 -
> include/configs/ls1021aiot.h | 1 -
> include/configs/socfpga_stratix10_socdk.h | 1 -
> include/linux/mtd/cfi.h | 32 +
> include/linux/mtd/spi-nor.h | 419 +++
> include/spi_flash.h | 105 +-
> 120 files changed, 4266 insertions(+), 2058 deletions(-)
> delete mode 100644 doc/SPI/README.dual-flash
> create mode 100644 drivers/mtd/spi/spi-nor-core.c
> create mode 100644 drivers/mtd/spi/spi-nor-ids.c
> create mode 100644 drivers/mtd/spi/spi-nor-tiny.c
> delete mode 100644 drivers/mtd/spi/spi_flash.c
> delete mode 100644 drivers/mtd/spi/spi_flash_ids.c
> create mode 100644 drivers/spi/spi-mem-nodm.c
> create mode 100644 include/linux/mtd/cfi.h
> create mode 100644 include/linux/mtd/spi-nor.h
>
> --
> 2.20.1
>
--
Regards
Vignesh
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2018-12-21 11:11 ` Vignesh R
@ 2018-12-21 13:29 ` Simon Goldschmidt
2018-12-22 7:43 ` Simon Goldschmidt
0 siblings, 1 reply; 33+ messages in thread
From: Simon Goldschmidt @ 2018-12-21 13:29 UTC (permalink / raw)
To: u-boot
Am 21.12.2018 um 12:11 schrieb Vignesh R:
> Hi Simon,
> [...]
>>
>> Hi Vignesh,
>>
>> I just did a quick test on this but it fails to boot. I guess this could
>> be a size problem.
>
> I guess. SPL_SPI_FLASH_TINY would help with SPL size issue here.
Yes, after enabling that it works. With the tiny framework, I get
~1.5KiB reduction compared to current mainline.
>
>> Unfortunately, the socfpga gen5 config does not
>> correctly check SPL size currently. I'll have to work on that. I'll test
>> your patch with a more limited config when I find the time.
>>
> Okay, thanks!
I can successfully boot with your v2 patch applied with the standard and
the tiny framework. However, allow me some more time to check SFDP (and
maybe BAR) and also to check that the correct opcodes are used
(stateless 4-byte opcodes should be used).
Regards,
Simon
>
> Regards
> Vignesh
>
>> Regards,
>> Simon
>>
>>
>> Change log:
>> Since v1:
>> Remove #ifindef __UBOOT__
>> Add back BAR support, but dont enable as default for all platform (see
>> 10/11 for more details)
>> Enable SPI_FLASH_TINY on boards where there is SPL size constraint as
>> seen on travis ci builds.
>> Drop sf_mtd changes for now as it seems to cause issues.
>> v1: https://patchwork.ozlabs.org/cover/1012146/
>>
>> Since RFC v2:
>> Fix issues reported by Simon Goldschmidt wrt 4 use of byte
>> addressing opcode
>> Fix issues in compiling SFDP code
>> Re organize file names and Makefile to simply spi-nor-tiny inclusion
>> Remove SPI_FLASH_BAR and SF_DUAL_FLASH as these are no longer used
>> RFC v2: https://patchwork.ozlabs.org/cover/1007589/
>>
>> Since RFC v1:
>> Add lightweight SPI flash stack for boards with SPL size constraints
>> Provide non DM version of spi-mem
>> Fix build issues on different platforms as reported by travis-ci on v1
>>
>> RFC v1: https://patchwork.ozlabs.org/cover/1004689/
>>
>> Vignesh R (11):
>> spi-mem: Claim SPI bus before spi mem access
>> spi: Add non DM version of SPI_MEM
>> sh: bitops: add hweight*() macros
>> mtd: spi: Port SPI NOR framework from Linux
>> mtd: spi: Switch to new SPI NOR framework
>> mtd: spi: Remove unused files
>> mtd: spi: Add lightweight SPI flash stack for SPL
>> configs: Enable SPI_FLASH_TINY for resource constrained boards
>> configs: Remove SF_DUAL_FLASH
>> configs: Don't use SPI_FLASH_BAR as default
>> MAINTAINERS: Add an entry for SPI NOR
>>
>> MAINTAINERS | 9 +
>> arch/arm/mach-omap2/am33xx/Kconfig | 1 -
>> arch/sh/include/asm/bitops.h | 4 +
>> common/spl/Kconfig | 21 +-
>> configs/alt_defconfig | 1 -
>> configs/am57xx_evm_defconfig | 1 -
>> configs/am57xx_hs_evm_defconfig | 1 -
>> configs/ap121_defconfig | 1 -
>> configs/ap143_defconfig | 1 -
>> configs/avnet_ultra96_rev1_defconfig | 1 -
>> configs/axm_defconfig | 1 +
>> configs/axs101_defconfig | 1 -
>> configs/axs103_defconfig | 1 -
>> configs/bg0900_defconfig | 1 -
>> configs/blanche_defconfig | 1 -
>> configs/cl-som-am57x_defconfig | 1 -
>> configs/clearfog_defconfig | 1 -
>> configs/cm_t43_defconfig | 1 -
>> configs/da850_am18xxevm_defconfig | 1 +
>> configs/da850evm_nand_defconfig | 2 +-
>> configs/db-88f6820-amc_defconfig | 1 -
>> configs/db-88f6820-gp_defconfig | 1 +
>> configs/display5_defconfig | 1 -
>> configs/display5_factory_defconfig | 1 -
>> configs/dra7xx_evm_defconfig | 1 -
>> configs/dra7xx_hs_evm_defconfig | 1 -
>> configs/ds109_defconfig | 1 -
>> configs/ds414_defconfig | 1 -
>> configs/evb-rv1108_defconfig | 1 -
>> configs/gose_defconfig | 1 -
>> configs/helios4_defconfig | 1 -
>> configs/k2g_evm_defconfig | 1 -
>> configs/k2g_hs_evm_defconfig | 1 -
>> configs/koelsch_defconfig | 1 -
>> configs/lager_defconfig | 1 -
>> configs/maxbcm_defconfig | 1 -
>> configs/mt7629_rfb_defconfig | 1 -
>> configs/mx6sxsabreauto_defconfig | 1 -
>> configs/mx6sxsabresd_defconfig | 1 -
>> configs/mx6ul_14x14_evk_defconfig | 1 -
>> configs/mx6ul_9x9_evk_defconfig | 1 -
>> configs/mx6ull_14x14_evk_defconfig | 1 -
>> configs/mx6ull_14x14_evk_plugin_defconfig | 1 -
>> configs/mx7dsabresd_qspi_defconfig | 1 -
>> configs/porter_defconfig | 2 +-
>> configs/r8a77970_eagle_defconfig | 1 -
>> configs/silk_defconfig | 1 -
>> configs/socfpga_arria5_defconfig | 1 -
>> configs/socfpga_cyclone5_defconfig | 1 -
>> configs/socfpga_is1_defconfig | 1 -
>> configs/socfpga_sockit_defconfig | 1 -
>> configs/socfpga_socrates_defconfig | 1 -
>> configs/socfpga_sr1500_defconfig | 1 -
>> configs/socfpga_stratix10_defconfig | 1 -
>> configs/stout_defconfig | 2 +-
>> configs/taurus_defconfig | 3 +-
>> configs/topic_miami_defconfig | 1 -
>> configs/topic_miamilite_defconfig | 2 -
>> configs/topic_miamiplus_defconfig | 2 -
>> configs/turris_omnia_defconfig | 2 +-
>> configs/xilinx_versal_virt_defconfig | 1 -
>> configs/xilinx_zynqmp_mini_qspi_defconfig | 2 -
>> configs/xilinx_zynqmp_zc1232_revA_defconfig | 2 -
>> configs/xilinx_zynqmp_zc1254_revA_defconfig | 2 -
>> configs/xilinx_zynqmp_zc1275_revA_defconfig | 2 -
>> configs/xilinx_zynqmp_zc1275_revB_defconfig | 2 -
>> .../xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 -
>> .../xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 1 -
>> .../xilinx_zynqmp_zc1751_xm018_dc4_defconfig | 1 -
>> configs/xilinx_zynqmp_zcu100_revC_defconfig | 1 -
>> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 1 -
>> configs/xilinx_zynqmp_zcu102_revA_defconfig | 1 -
>> configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 -
>> configs/xilinx_zynqmp_zcu104_revA_defconfig | 2 -
>> configs/xilinx_zynqmp_zcu104_revC_defconfig | 2 -
>> configs/xilinx_zynqmp_zcu106_revA_defconfig | 2 -
>> configs/xilinx_zynqmp_zcu111_revA_defconfig | 1 -
>> configs/zynq_cc108_defconfig | 1 -
>> configs/zynq_cse_qspi_defconfig | 1 -
>> configs/zynq_dlc20_rev1_0_defconfig | 1 -
>> configs/zynq_microzed_defconfig | 1 -
>> configs/zynq_minized_defconfig | 1 -
>> configs/zynq_z_turn_defconfig | 1 -
>> configs/zynq_zc702_defconfig | 1 -
>> configs/zynq_zc706_defconfig | 1 -
>> configs/zynq_zc770_xm010_defconfig | 1 -
>> configs/zynq_zc770_xm013_defconfig | 1 -
>> configs/zynq_zed_defconfig | 1 -
>> configs/zynq_zybo_defconfig | 1 -
>> configs/zynq_zybo_z7_defconfig | 1 -
>> doc/SPI/README.dual-flash | 92 -
>> doc/SPI/README.ti_qspi_dra_test | 1 -
>> drivers/mtd/spi/Kconfig | 16 +-
>> drivers/mtd/spi/Makefile | 12 +-
>> drivers/mtd/spi/sandbox.c | 36 +-
>> drivers/mtd/spi/sf_dataflash.c | 11 +-
>> drivers/mtd/spi/sf_internal.h | 225 +-
>> drivers/mtd/spi/sf_probe.c | 33 +-
>> drivers/mtd/spi/spi-nor-core.c | 2432 +++++++++++++++++
>> drivers/mtd/spi/spi-nor-ids.c | 297 ++
>> drivers/mtd/spi/spi-nor-tiny.c | 810 ++++++
>> drivers/mtd/spi/spi_flash.c | 1337 ---------
>> drivers/mtd/spi/spi_flash_ids.c | 211 --
>> drivers/spi/Kconfig | 9 +-
>> drivers/spi/Makefile | 1 +
>> drivers/spi/spi-mem-nodm.c | 89 +
>> drivers/spi/spi-mem.c | 6 +
>> drivers/spi/stm32_qspi.c | 4 +-
>> include/configs/T102xQDS.h | 1 -
>> include/configs/T102xRDB.h | 1 -
>> include/configs/T104xRDB.h | 1 -
>> include/configs/T208xQDS.h | 1 -
>> include/configs/T208xRDB.h | 1 -
>> include/configs/gw_ventana.h | 1 -
>> include/configs/km/kmp204x-common.h | 1 -
>> include/configs/ls1021aiot.h | 1 -
>> include/configs/socfpga_stratix10_socdk.h | 1 -
>> include/linux/mtd/cfi.h | 32 +
>> include/linux/mtd/spi-nor.h | 419 +++
>> include/spi_flash.h | 105 +-
>> 120 files changed, 4266 insertions(+), 2058 deletions(-)
>> delete mode 100644 doc/SPI/README.dual-flash
>> create mode 100644 drivers/mtd/spi/spi-nor-core.c
>> create mode 100644 drivers/mtd/spi/spi-nor-ids.c
>> create mode 100644 drivers/mtd/spi/spi-nor-tiny.c
>> delete mode 100644 drivers/mtd/spi/spi_flash.c
>> delete mode 100644 drivers/mtd/spi/spi_flash_ids.c
>> create mode 100644 drivers/spi/spi-mem-nodm.c
>> create mode 100644 include/linux/mtd/cfi.h
>> create mode 100644 include/linux/mtd/spi-nor.h
>>
>> --
>> 2.20.1
>>
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2018-12-21 13:29 ` Simon Goldschmidt
@ 2018-12-22 7:43 ` Simon Goldschmidt
2019-01-09 9:26 ` Vignesh R
0 siblings, 1 reply; 33+ messages in thread
From: Simon Goldschmidt @ 2018-12-22 7:43 UTC (permalink / raw)
To: u-boot
Am 21.12.2018 um 14:29 schrieb Simon Goldschmidt:
> Am 21.12.2018 um 12:11 schrieb Vignesh R:
>> Hi Simon,
>> [...]
>>>
>>> Hi Vignesh,
>>>
>>> I just did a quick test on this but it fails to boot. I guess this could
>>> be a size problem.
>>
>> I guess. SPL_SPI_FLASH_TINY would help with SPL size issue here.
>
> Yes, after enabling that it works. With the tiny framework, I get
> ~1.5KiB reduction compared to current mainline.
>
>>
>>> Unfortunately, the socfpga gen5 config does not
>>> correctly check SPL size currently. I'll have to work on that. I'll test
>>> your patch with a more limited config when I find the time.
>>>
>> Okay, thanks!
>
> I can successfully boot with your v2 patch applied with the standard and
> the tiny framework. However, allow me some more time to check SFDP (and
> maybe BAR) and also to check that the correct opcodes are used
> (stateless 4-byte opcodes should be used).
After testing different configs with SPL and U-Boot:
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
However, two suggestions:
- I would recommend to enable SPL_SPI_FLASH_TINY by default to prevent
SPL size increasement for any board
- SPL_SPI_FLASH_TINY does not provide BAR support and the Kconfig option
does not reflect this. This should probably be fixed before making
SPL_SPI_FLASH_TINY the default.
Regards,
Simon
>
> Regards,
> Simon
>
>>
>> Regards
>> Vignesh
>>
>>> Regards,
>>> Simon
>>>
>>>
>>> Change log:
>>> Since v1:
>>> Remove #ifindef __UBOOT__
>>> Add back BAR support, but dont enable as default for all platform (see
>>> 10/11 for more details)
>>> Enable SPI_FLASH_TINY on boards where there is SPL size constraint as
>>> seen on travis ci builds.
>>> Drop sf_mtd changes for now as it seems to cause issues.
>>> v1: https://patchwork.ozlabs.org/cover/1012146/
>>>
>>> Since RFC v2:
>>> Fix issues reported by Simon Goldschmidt wrt 4 use of byte
>>> addressing opcode
>>> Fix issues in compiling SFDP code
>>> Re organize file names and Makefile to simply spi-nor-tiny inclusion
>>> Remove SPI_FLASH_BAR and SF_DUAL_FLASH as these are no longer used
>>> RFC v2: https://patchwork.ozlabs.org/cover/1007589/
>>>
>>> Since RFC v1:
>>> Add lightweight SPI flash stack for boards with SPL size constraints
>>> Provide non DM version of spi-mem
>>> Fix build issues on different platforms as reported by travis-ci on v1
>>>
>>> RFC v1: https://patchwork.ozlabs.org/cover/1004689/
>>>
>>> Vignesh R (11):
>>> spi-mem: Claim SPI bus before spi mem access
>>> spi: Add non DM version of SPI_MEM
>>> sh: bitops: add hweight*() macros
>>> mtd: spi: Port SPI NOR framework from Linux
>>> mtd: spi: Switch to new SPI NOR framework
>>> mtd: spi: Remove unused files
>>> mtd: spi: Add lightweight SPI flash stack for SPL
>>> configs: Enable SPI_FLASH_TINY for resource constrained boards
>>> configs: Remove SF_DUAL_FLASH
>>> configs: Don't use SPI_FLASH_BAR as default
>>> MAINTAINERS: Add an entry for SPI NOR
>>>
>>> MAINTAINERS | 9 +
>>> arch/arm/mach-omap2/am33xx/Kconfig | 1 -
>>> arch/sh/include/asm/bitops.h | 4 +
>>> common/spl/Kconfig | 21 +-
>>> configs/alt_defconfig | 1 -
>>> configs/am57xx_evm_defconfig | 1 -
>>> configs/am57xx_hs_evm_defconfig | 1 -
>>> configs/ap121_defconfig | 1 -
>>> configs/ap143_defconfig | 1 -
>>> configs/avnet_ultra96_rev1_defconfig | 1 -
>>> configs/axm_defconfig | 1 +
>>> configs/axs101_defconfig | 1 -
>>> configs/axs103_defconfig | 1 -
>>> configs/bg0900_defconfig | 1 -
>>> configs/blanche_defconfig | 1 -
>>> configs/cl-som-am57x_defconfig | 1 -
>>> configs/clearfog_defconfig | 1 -
>>> configs/cm_t43_defconfig | 1 -
>>> configs/da850_am18xxevm_defconfig | 1 +
>>> configs/da850evm_nand_defconfig | 2 +-
>>> configs/db-88f6820-amc_defconfig | 1 -
>>> configs/db-88f6820-gp_defconfig | 1 +
>>> configs/display5_defconfig | 1 -
>>> configs/display5_factory_defconfig | 1 -
>>> configs/dra7xx_evm_defconfig | 1 -
>>> configs/dra7xx_hs_evm_defconfig | 1 -
>>> configs/ds109_defconfig | 1 -
>>> configs/ds414_defconfig | 1 -
>>> configs/evb-rv1108_defconfig | 1 -
>>> configs/gose_defconfig | 1 -
>>> configs/helios4_defconfig | 1 -
>>> configs/k2g_evm_defconfig | 1 -
>>> configs/k2g_hs_evm_defconfig | 1 -
>>> configs/koelsch_defconfig | 1 -
>>> configs/lager_defconfig | 1 -
>>> configs/maxbcm_defconfig | 1 -
>>> configs/mt7629_rfb_defconfig | 1 -
>>> configs/mx6sxsabreauto_defconfig | 1 -
>>> configs/mx6sxsabresd_defconfig | 1 -
>>> configs/mx6ul_14x14_evk_defconfig | 1 -
>>> configs/mx6ul_9x9_evk_defconfig | 1 -
>>> configs/mx6ull_14x14_evk_defconfig | 1 -
>>> configs/mx6ull_14x14_evk_plugin_defconfig | 1 -
>>> configs/mx7dsabresd_qspi_defconfig | 1 -
>>> configs/porter_defconfig | 2 +-
>>> configs/r8a77970_eagle_defconfig | 1 -
>>> configs/silk_defconfig | 1 -
>>> configs/socfpga_arria5_defconfig | 1 -
>>> configs/socfpga_cyclone5_defconfig | 1 -
>>> configs/socfpga_is1_defconfig | 1 -
>>> configs/socfpga_sockit_defconfig | 1 -
>>> configs/socfpga_socrates_defconfig | 1 -
>>> configs/socfpga_sr1500_defconfig | 1 -
>>> configs/socfpga_stratix10_defconfig | 1 -
>>> configs/stout_defconfig | 2 +-
>>> configs/taurus_defconfig | 3 +-
>>> configs/topic_miami_defconfig | 1 -
>>> configs/topic_miamilite_defconfig | 2 -
>>> configs/topic_miamiplus_defconfig | 2 -
>>> configs/turris_omnia_defconfig | 2 +-
>>> configs/xilinx_versal_virt_defconfig | 1 -
>>> configs/xilinx_zynqmp_mini_qspi_defconfig | 2 -
>>> configs/xilinx_zynqmp_zc1232_revA_defconfig | 2 -
>>> configs/xilinx_zynqmp_zc1254_revA_defconfig | 2 -
>>> configs/xilinx_zynqmp_zc1275_revA_defconfig | 2 -
>>> configs/xilinx_zynqmp_zc1275_revB_defconfig | 2 -
>>> .../xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 -
>>> .../xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 1 -
>>> .../xilinx_zynqmp_zc1751_xm018_dc4_defconfig | 1 -
>>> configs/xilinx_zynqmp_zcu100_revC_defconfig | 1 -
>>> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 1 -
>>> configs/xilinx_zynqmp_zcu102_revA_defconfig | 1 -
>>> configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 -
>>> configs/xilinx_zynqmp_zcu104_revA_defconfig | 2 -
>>> configs/xilinx_zynqmp_zcu104_revC_defconfig | 2 -
>>> configs/xilinx_zynqmp_zcu106_revA_defconfig | 2 -
>>> configs/xilinx_zynqmp_zcu111_revA_defconfig | 1 -
>>> configs/zynq_cc108_defconfig | 1 -
>>> configs/zynq_cse_qspi_defconfig | 1 -
>>> configs/zynq_dlc20_rev1_0_defconfig | 1 -
>>> configs/zynq_microzed_defconfig | 1 -
>>> configs/zynq_minized_defconfig | 1 -
>>> configs/zynq_z_turn_defconfig | 1 -
>>> configs/zynq_zc702_defconfig | 1 -
>>> configs/zynq_zc706_defconfig | 1 -
>>> configs/zynq_zc770_xm010_defconfig | 1 -
>>> configs/zynq_zc770_xm013_defconfig | 1 -
>>> configs/zynq_zed_defconfig | 1 -
>>> configs/zynq_zybo_defconfig | 1 -
>>> configs/zynq_zybo_z7_defconfig | 1 -
>>> doc/SPI/README.dual-flash | 92 -
>>> doc/SPI/README.ti_qspi_dra_test | 1 -
>>> drivers/mtd/spi/Kconfig | 16 +-
>>> drivers/mtd/spi/Makefile | 12 +-
>>> drivers/mtd/spi/sandbox.c | 36 +-
>>> drivers/mtd/spi/sf_dataflash.c | 11 +-
>>> drivers/mtd/spi/sf_internal.h | 225 +-
>>> drivers/mtd/spi/sf_probe.c | 33 +-
>>> drivers/mtd/spi/spi-nor-core.c | 2432 +++++++++++++++++
>>> drivers/mtd/spi/spi-nor-ids.c | 297 ++
>>> drivers/mtd/spi/spi-nor-tiny.c | 810 ++++++
>>> drivers/mtd/spi/spi_flash.c | 1337 ---------
>>> drivers/mtd/spi/spi_flash_ids.c | 211 --
>>> drivers/spi/Kconfig | 9 +-
>>> drivers/spi/Makefile | 1 +
>>> drivers/spi/spi-mem-nodm.c | 89 +
>>> drivers/spi/spi-mem.c | 6 +
>>> drivers/spi/stm32_qspi.c | 4 +-
>>> include/configs/T102xQDS.h | 1 -
>>> include/configs/T102xRDB.h | 1 -
>>> include/configs/T104xRDB.h | 1 -
>>> include/configs/T208xQDS.h | 1 -
>>> include/configs/T208xRDB.h | 1 -
>>> include/configs/gw_ventana.h | 1 -
>>> include/configs/km/kmp204x-common.h | 1 -
>>> include/configs/ls1021aiot.h | 1 -
>>> include/configs/socfpga_stratix10_socdk.h | 1 -
>>> include/linux/mtd/cfi.h | 32 +
>>> include/linux/mtd/spi-nor.h | 419 +++
>>> include/spi_flash.h | 105 +-
>>> 120 files changed, 4266 insertions(+), 2058 deletions(-)
>>> delete mode 100644 doc/SPI/README.dual-flash
>>> create mode 100644 drivers/mtd/spi/spi-nor-core.c
>>> create mode 100644 drivers/mtd/spi/spi-nor-ids.c
>>> create mode 100644 drivers/mtd/spi/spi-nor-tiny.c
>>> delete mode 100644 drivers/mtd/spi/spi_flash.c
>>> delete mode 100644 drivers/mtd/spi/spi_flash_ids.c
>>> create mode 100644 drivers/spi/spi-mem-nodm.c
>>> create mode 100644 include/linux/mtd/cfi.h
>>> create mode 100644 include/linux/mtd/spi-nor.h
>>>
>>> --
>>> 2.20.1
>>>
>>
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2018-12-22 7:43 ` Simon Goldschmidt
@ 2019-01-09 9:26 ` Vignesh R
0 siblings, 0 replies; 33+ messages in thread
From: Vignesh R @ 2019-01-09 9:26 UTC (permalink / raw)
To: u-boot
On 22/12/18 1:13 PM, Simon Goldschmidt wrote:
> Am 21.12.2018 um 14:29 schrieb Simon Goldschmidt:
>> Am 21.12.2018 um 12:11 schrieb Vignesh R:
>>> Hi Simon,
>>> [...]
>>>>
>>>> Hi Vignesh,
>>>>
>>>> I just did a quick test on this but it fails to boot. I guess this could
>>>> be a size problem.
>>>
>>> I guess. SPL_SPI_FLASH_TINY would help with SPL size issue here.
>>
>> Yes, after enabling that it works. With the tiny framework, I get
>> ~1.5KiB reduction compared to current mainline.
>>
>>>
>>>> Unfortunately, the socfpga gen5 config does not
>>>> correctly check SPL size currently. I'll have to work on that. I'll test
>>>> your patch with a more limited config when I find the time.
>>>>
>>> Okay, thanks!
>>
>> I can successfully boot with your v2 patch applied with the standard and
>> the tiny framework. However, allow me some more time to check SFDP (and
>> maybe BAR) and also to check that the correct opcodes are used
>> (stateless 4-byte opcodes should be used).
>
> After testing different configs with SPL and U-Boot:
>
> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
>
> However, two suggestions:
> - I would recommend to enable SPL_SPI_FLASH_TINY by default to prevent
> SPL size increasement for any board
I am fine with doing this if there are no objections on "[PATCH v2
10/11] configs: Don't use SPI_FLASH_BAR as default"
> - SPL_SPI_FLASH_TINY does not provide BAR support and the Kconfig option
> does not reflect this. This should probably be fixed before making
> SPL_SPI_FLASH_TINY the default.
>
Ok, I will make SPI_FLASH_BAR depend on !SPL_SPI_FLASH_TINY
Thanks for the suggestions!
> Regards,
> Simon
>
>>
>> Regards,
>> Simon
>>
>>>
>>> Regards
>>> Vignesh
>>>
>>>> Regards,
>>>> Simon
>>>>
>>>>
>>>> Change log:
>>>> Since v1:
>>>> Remove #ifindef __UBOOT__
>>>> Add back BAR support, but dont enable as default for all platform (see
>>>> 10/11 for more details)
>>>> Enable SPI_FLASH_TINY on boards where there is SPL size constraint as
>>>> seen on travis ci builds.
>>>> Drop sf_mtd changes for now as it seems to cause issues.
>>>> v1: https://patchwork.ozlabs.org/cover/1012146/
>>>>
>>>> Since RFC v2:
>>>> Fix issues reported by Simon Goldschmidt wrt 4 use of byte
>>>> addressing opcode
>>>> Fix issues in compiling SFDP code
>>>> Re organize file names and Makefile to simply spi-nor-tiny inclusion
>>>> Remove SPI_FLASH_BAR and SF_DUAL_FLASH as these are no longer used
>>>> RFC v2: https://patchwork.ozlabs.org/cover/1007589/
>>>>
>>>> Since RFC v1:
>>>> Add lightweight SPI flash stack for boards with SPL size constraints
>>>> Provide non DM version of spi-mem
>>>> Fix build issues on different platforms as reported by travis-ci on v1
>>>>
>>>> RFC v1: https://patchwork.ozlabs.org/cover/1004689/
>>>>
>>>> Vignesh R (11):
>>>> spi-mem: Claim SPI bus before spi mem access
>>>> spi: Add non DM version of SPI_MEM
>>>> sh: bitops: add hweight*() macros
>>>> mtd: spi: Port SPI NOR framework from Linux
>>>> mtd: spi: Switch to new SPI NOR framework
>>>> mtd: spi: Remove unused files
>>>> mtd: spi: Add lightweight SPI flash stack for SPL
>>>> configs: Enable SPI_FLASH_TINY for resource constrained boards
>>>> configs: Remove SF_DUAL_FLASH
>>>> configs: Don't use SPI_FLASH_BAR as default
>>>> MAINTAINERS: Add an entry for SPI NOR
>>>>
>>>> MAINTAINERS | 9 +
>>>> arch/arm/mach-omap2/am33xx/Kconfig | 1 -
>>>> arch/sh/include/asm/bitops.h | 4 +
>>>> common/spl/Kconfig | 21 +-
>>>> configs/alt_defconfig | 1 -
>>>> configs/am57xx_evm_defconfig | 1 -
>>>> configs/am57xx_hs_evm_defconfig | 1 -
>>>> configs/ap121_defconfig | 1 -
>>>> configs/ap143_defconfig | 1 -
>>>> configs/avnet_ultra96_rev1_defconfig | 1 -
>>>> configs/axm_defconfig | 1 +
>>>> configs/axs101_defconfig | 1 -
>>>> configs/axs103_defconfig | 1 -
>>>> configs/bg0900_defconfig | 1 -
>>>> configs/blanche_defconfig | 1 -
>>>> configs/cl-som-am57x_defconfig | 1 -
>>>> configs/clearfog_defconfig | 1 -
>>>> configs/cm_t43_defconfig | 1 -
>>>> configs/da850_am18xxevm_defconfig | 1 +
>>>> configs/da850evm_nand_defconfig | 2 +-
>>>> configs/db-88f6820-amc_defconfig | 1 -
>>>> configs/db-88f6820-gp_defconfig | 1 +
>>>> configs/display5_defconfig | 1 -
>>>> configs/display5_factory_defconfig | 1 -
>>>> configs/dra7xx_evm_defconfig | 1 -
>>>> configs/dra7xx_hs_evm_defconfig | 1 -
>>>> configs/ds109_defconfig | 1 -
>>>> configs/ds414_defconfig | 1 -
>>>> configs/evb-rv1108_defconfig | 1 -
>>>> configs/gose_defconfig | 1 -
>>>> configs/helios4_defconfig | 1 -
>>>> configs/k2g_evm_defconfig | 1 -
>>>> configs/k2g_hs_evm_defconfig | 1 -
>>>> configs/koelsch_defconfig | 1 -
>>>> configs/lager_defconfig | 1 -
>>>> configs/maxbcm_defconfig | 1 -
>>>> configs/mt7629_rfb_defconfig | 1 -
>>>> configs/mx6sxsabreauto_defconfig | 1 -
>>>> configs/mx6sxsabresd_defconfig | 1 -
>>>> configs/mx6ul_14x14_evk_defconfig | 1 -
>>>> configs/mx6ul_9x9_evk_defconfig | 1 -
>>>> configs/mx6ull_14x14_evk_defconfig | 1 -
>>>> configs/mx6ull_14x14_evk_plugin_defconfig | 1 -
>>>> configs/mx7dsabresd_qspi_defconfig | 1 -
>>>> configs/porter_defconfig | 2 +-
>>>> configs/r8a77970_eagle_defconfig | 1 -
>>>> configs/silk_defconfig | 1 -
>>>> configs/socfpga_arria5_defconfig | 1 -
>>>> configs/socfpga_cyclone5_defconfig | 1 -
>>>> configs/socfpga_is1_defconfig | 1 -
>>>> configs/socfpga_sockit_defconfig | 1 -
>>>> configs/socfpga_socrates_defconfig | 1 -
>>>> configs/socfpga_sr1500_defconfig | 1 -
>>>> configs/socfpga_stratix10_defconfig | 1 -
>>>> configs/stout_defconfig | 2 +-
>>>> configs/taurus_defconfig | 3 +-
>>>> configs/topic_miami_defconfig | 1 -
>>>> configs/topic_miamilite_defconfig | 2 -
>>>> configs/topic_miamiplus_defconfig | 2 -
>>>> configs/turris_omnia_defconfig | 2 +-
>>>> configs/xilinx_versal_virt_defconfig | 1 -
>>>> configs/xilinx_zynqmp_mini_qspi_defconfig | 2 -
>>>> configs/xilinx_zynqmp_zc1232_revA_defconfig | 2 -
>>>> configs/xilinx_zynqmp_zc1254_revA_defconfig | 2 -
>>>> configs/xilinx_zynqmp_zc1275_revA_defconfig | 2 -
>>>> configs/xilinx_zynqmp_zc1275_revB_defconfig | 2 -
>>>> .../xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 -
>>>> .../xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 1 -
>>>> .../xilinx_zynqmp_zc1751_xm018_dc4_defconfig | 1 -
>>>> configs/xilinx_zynqmp_zcu100_revC_defconfig | 1 -
>>>> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 1 -
>>>> configs/xilinx_zynqmp_zcu102_revA_defconfig | 1 -
>>>> configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 -
>>>> configs/xilinx_zynqmp_zcu104_revA_defconfig | 2 -
>>>> configs/xilinx_zynqmp_zcu104_revC_defconfig | 2 -
>>>> configs/xilinx_zynqmp_zcu106_revA_defconfig | 2 -
>>>> configs/xilinx_zynqmp_zcu111_revA_defconfig | 1 -
>>>> configs/zynq_cc108_defconfig | 1 -
>>>> configs/zynq_cse_qspi_defconfig | 1 -
>>>> configs/zynq_dlc20_rev1_0_defconfig | 1 -
>>>> configs/zynq_microzed_defconfig | 1 -
>>>> configs/zynq_minized_defconfig | 1 -
>>>> configs/zynq_z_turn_defconfig | 1 -
>>>> configs/zynq_zc702_defconfig | 1 -
>>>> configs/zynq_zc706_defconfig | 1 -
>>>> configs/zynq_zc770_xm010_defconfig | 1 -
>>>> configs/zynq_zc770_xm013_defconfig | 1 -
>>>> configs/zynq_zed_defconfig | 1 -
>>>> configs/zynq_zybo_defconfig | 1 -
>>>> configs/zynq_zybo_z7_defconfig | 1 -
>>>> doc/SPI/README.dual-flash | 92 -
>>>> doc/SPI/README.ti_qspi_dra_test | 1 -
>>>> drivers/mtd/spi/Kconfig | 16 +-
>>>> drivers/mtd/spi/Makefile | 12 +-
>>>> drivers/mtd/spi/sandbox.c | 36 +-
>>>> drivers/mtd/spi/sf_dataflash.c | 11 +-
>>>> drivers/mtd/spi/sf_internal.h | 225 +-
>>>> drivers/mtd/spi/sf_probe.c | 33 +-
>>>> drivers/mtd/spi/spi-nor-core.c | 2432 +++++++++++++++++
>>>> drivers/mtd/spi/spi-nor-ids.c | 297 ++
>>>> drivers/mtd/spi/spi-nor-tiny.c | 810 ++++++
>>>> drivers/mtd/spi/spi_flash.c | 1337 ---------
>>>> drivers/mtd/spi/spi_flash_ids.c | 211 --
>>>> drivers/spi/Kconfig | 9 +-
>>>> drivers/spi/Makefile | 1 +
>>>> drivers/spi/spi-mem-nodm.c | 89 +
>>>> drivers/spi/spi-mem.c | 6 +
>>>> drivers/spi/stm32_qspi.c | 4 +-
>>>> include/configs/T102xQDS.h | 1 -
>>>> include/configs/T102xRDB.h | 1 -
>>>> include/configs/T104xRDB.h | 1 -
>>>> include/configs/T208xQDS.h | 1 -
>>>> include/configs/T208xRDB.h | 1 -
>>>> include/configs/gw_ventana.h | 1 -
>>>> include/configs/km/kmp204x-common.h | 1 -
>>>> include/configs/ls1021aiot.h | 1 -
>>>> include/configs/socfpga_stratix10_socdk.h | 1 -
>>>> include/linux/mtd/cfi.h | 32 +
>>>> include/linux/mtd/spi-nor.h | 419 +++
>>>> include/spi_flash.h | 105 +-
>>>> 120 files changed, 4266 insertions(+), 2058 deletions(-)
>>>> delete mode 100644 doc/SPI/README.dual-flash
>>>> create mode 100644 drivers/mtd/spi/spi-nor-core.c
>>>> create mode 100644 drivers/mtd/spi/spi-nor-ids.c
>>>> create mode 100644 drivers/mtd/spi/spi-nor-tiny.c
>>>> delete mode 100644 drivers/mtd/spi/spi_flash.c
>>>> delete mode 100644 drivers/mtd/spi/spi_flash_ids.c
>>>> create mode 100644 drivers/spi/spi-mem-nodm.c
>>>> create mode 100644 include/linux/mtd/cfi.h
>>>> create mode 100644 include/linux/mtd/spi-nor.h
>>>>
>>>> --
>>>> 2.20.1
>>>>
>>>
>>
>
--
Regards
Vignesh
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (12 preceding siblings ...)
2018-12-21 10:33 ` Simon Goldschmidt
@ 2019-01-14 15:02 ` Vignesh R
2019-01-14 15:05 ` Tom Rini
2019-01-21 11:58 ` Vignesh R
2019-01-21 17:14 ` Horatiu Vultur
14 siblings, 2 replies; 33+ messages in thread
From: Vignesh R @ 2019-01-14 15:02 UTC (permalink / raw)
To: u-boot
Hi Jagan,
Could you please review v2? If we plan to merge this series for
v2019.04, we should probably plan to take it a bit early so as to
address any regression or fall out in time. Thanks!
Regards
Vignesh
On 21/12/18 12:08 PM, Vignesh R wrote:
> U-Boot SPI NOR support (sf layer) is quite outdated as it does not
> support 4 byte addressing opcodes, SFDP table parsing and different types of
> quad mode enable sequences. Many newer flashes no longer support BANK
> registers used by sf layer to a access >16MB space.
> Also, many SPI controllers have special MMIO interfaces which provide
> accelerated read/write access but require knowledge of flash parameters
> to make use of it. Recent spi-mem layer provides a way to support such
> flashes but sf layer isn't using that.
> This patch series syncs SPI NOR framework from Linux v4.19. It also adds
> spi-mem support on top.
> So, we gain 4byte addressing support and SFDP support. This makes
> migrating to U-Boot MTD framework easier.
>
> Tested with few Spansion, micron and macronix flashes with TI's dra7xx,
> k2g, am43xx EVMs. I dont have access to flashes from other vendors. So,
> I would greatly appreciate testing on other platforms. Complete series
> with dependencies here[1]
>
> For clean build on some platforms, depends on CONFIG_SPI_FLASH migration
> to defconfigs [2]
>
> [1] https://github.com/r-vignesh/u-boot.git branch: spi-nor-mig-patch-v2
> [2] https://patchwork.ozlabs.org/patch/1007485/
>
> Simon, Stefan, Thanks for testing previous versions.
> I haven't carried Tested-by's here as I have added back SPI_FLASH_BAR
> support (but isn't enabled by default). Would be great if you could
> retest this series.
> I am hoping there won't be any major rework/changes after this round.
>
> Change log:
> Since v1:
> Remove #ifindef __UBOOT__
> Add back BAR support, but dont enable as default for all platform (see
> 10/11 for more details)
> Enable SPI_FLASH_TINY on boards where there is SPL size constraint as
> seen on travis ci builds.
> Drop sf_mtd changes for now as it seems to cause issues.
> v1: https://patchwork.ozlabs.org/cover/1012146/
>
> Since RFC v2:
> Fix issues reported by Simon Goldschmidt wrt 4 use of byte addressing opcode
> Fix issues in compiling SFDP code
> Re organize file names and Makefile to simply spi-nor-tiny inclusion
> Remove SPI_FLASH_BAR and SF_DUAL_FLASH as these are no longer used
> RFC v2: https://patchwork.ozlabs.org/cover/1007589/
>
> Since RFC v1:
> Add lightweight SPI flash stack for boards with SPL size constraints
> Provide non DM version of spi-mem
> Fix build issues on different platforms as reported by travis-ci on v1
>
> RFC v1: https://patchwork.ozlabs.org/cover/1004689/
>
> Vignesh R (11):
> spi-mem: Claim SPI bus before spi mem access
> spi: Add non DM version of SPI_MEM
> sh: bitops: add hweight*() macros
> mtd: spi: Port SPI NOR framework from Linux
> mtd: spi: Switch to new SPI NOR framework
> mtd: spi: Remove unused files
> mtd: spi: Add lightweight SPI flash stack for SPL
> configs: Enable SPI_FLASH_TINY for resource constrained boards
> configs: Remove SF_DUAL_FLASH
> configs: Don't use SPI_FLASH_BAR as default
> MAINTAINERS: Add an entry for SPI NOR
>
> MAINTAINERS | 9 +
> arch/arm/mach-omap2/am33xx/Kconfig | 1 -
> arch/sh/include/asm/bitops.h | 4 +
> common/spl/Kconfig | 21 +-
> configs/alt_defconfig | 1 -
> configs/am57xx_evm_defconfig | 1 -
> configs/am57xx_hs_evm_defconfig | 1 -
> configs/ap121_defconfig | 1 -
> configs/ap143_defconfig | 1 -
> configs/avnet_ultra96_rev1_defconfig | 1 -
> configs/axm_defconfig | 1 +
> configs/axs101_defconfig | 1 -
> configs/axs103_defconfig | 1 -
> configs/bg0900_defconfig | 1 -
> configs/blanche_defconfig | 1 -
> configs/cl-som-am57x_defconfig | 1 -
> configs/clearfog_defconfig | 1 -
> configs/cm_t43_defconfig | 1 -
> configs/da850_am18xxevm_defconfig | 1 +
> configs/da850evm_nand_defconfig | 2 +-
> configs/db-88f6820-amc_defconfig | 1 -
> configs/db-88f6820-gp_defconfig | 1 +
> configs/display5_defconfig | 1 -
> configs/display5_factory_defconfig | 1 -
> configs/dra7xx_evm_defconfig | 1 -
> configs/dra7xx_hs_evm_defconfig | 1 -
> configs/ds109_defconfig | 1 -
> configs/ds414_defconfig | 1 -
> configs/evb-rv1108_defconfig | 1 -
> configs/gose_defconfig | 1 -
> configs/helios4_defconfig | 1 -
> configs/k2g_evm_defconfig | 1 -
> configs/k2g_hs_evm_defconfig | 1 -
> configs/koelsch_defconfig | 1 -
> configs/lager_defconfig | 1 -
> configs/maxbcm_defconfig | 1 -
> configs/mt7629_rfb_defconfig | 1 -
> configs/mx6sxsabreauto_defconfig | 1 -
> configs/mx6sxsabresd_defconfig | 1 -
> configs/mx6ul_14x14_evk_defconfig | 1 -
> configs/mx6ul_9x9_evk_defconfig | 1 -
> configs/mx6ull_14x14_evk_defconfig | 1 -
> configs/mx6ull_14x14_evk_plugin_defconfig | 1 -
> configs/mx7dsabresd_qspi_defconfig | 1 -
> configs/porter_defconfig | 2 +-
> configs/r8a77970_eagle_defconfig | 1 -
> configs/silk_defconfig | 1 -
> configs/socfpga_arria5_defconfig | 1 -
> configs/socfpga_cyclone5_defconfig | 1 -
> configs/socfpga_is1_defconfig | 1 -
> configs/socfpga_sockit_defconfig | 1 -
> configs/socfpga_socrates_defconfig | 1 -
> configs/socfpga_sr1500_defconfig | 1 -
> configs/socfpga_stratix10_defconfig | 1 -
> configs/stout_defconfig | 2 +-
> configs/taurus_defconfig | 3 +-
> configs/topic_miami_defconfig | 1 -
> configs/topic_miamilite_defconfig | 2 -
> configs/topic_miamiplus_defconfig | 2 -
> configs/turris_omnia_defconfig | 2 +-
> configs/xilinx_versal_virt_defconfig | 1 -
> configs/xilinx_zynqmp_mini_qspi_defconfig | 2 -
> configs/xilinx_zynqmp_zc1232_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1254_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1275_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1275_revB_defconfig | 2 -
> .../xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 -
> .../xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 1 -
> .../xilinx_zynqmp_zc1751_xm018_dc4_defconfig | 1 -
> configs/xilinx_zynqmp_zcu100_revC_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_revA_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 -
> configs/xilinx_zynqmp_zcu104_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zcu104_revC_defconfig | 2 -
> configs/xilinx_zynqmp_zcu106_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zcu111_revA_defconfig | 1 -
> configs/zynq_cc108_defconfig | 1 -
> configs/zynq_cse_qspi_defconfig | 1 -
> configs/zynq_dlc20_rev1_0_defconfig | 1 -
> configs/zynq_microzed_defconfig | 1 -
> configs/zynq_minized_defconfig | 1 -
> configs/zynq_z_turn_defconfig | 1 -
> configs/zynq_zc702_defconfig | 1 -
> configs/zynq_zc706_defconfig | 1 -
> configs/zynq_zc770_xm010_defconfig | 1 -
> configs/zynq_zc770_xm013_defconfig | 1 -
> configs/zynq_zed_defconfig | 1 -
> configs/zynq_zybo_defconfig | 1 -
> configs/zynq_zybo_z7_defconfig | 1 -
> doc/SPI/README.dual-flash | 92 -
> doc/SPI/README.ti_qspi_dra_test | 1 -
> drivers/mtd/spi/Kconfig | 16 +-
> drivers/mtd/spi/Makefile | 12 +-
> drivers/mtd/spi/sandbox.c | 36 +-
> drivers/mtd/spi/sf_dataflash.c | 11 +-
> drivers/mtd/spi/sf_internal.h | 225 +-
> drivers/mtd/spi/sf_probe.c | 33 +-
> drivers/mtd/spi/spi-nor-core.c | 2432 +++++++++++++++++
> drivers/mtd/spi/spi-nor-ids.c | 297 ++
> drivers/mtd/spi/spi-nor-tiny.c | 810 ++++++
> drivers/mtd/spi/spi_flash.c | 1337 ---------
> drivers/mtd/spi/spi_flash_ids.c | 211 --
> drivers/spi/Kconfig | 9 +-
> drivers/spi/Makefile | 1 +
> drivers/spi/spi-mem-nodm.c | 89 +
> drivers/spi/spi-mem.c | 6 +
> drivers/spi/stm32_qspi.c | 4 +-
> include/configs/T102xQDS.h | 1 -
> include/configs/T102xRDB.h | 1 -
> include/configs/T104xRDB.h | 1 -
> include/configs/T208xQDS.h | 1 -
> include/configs/T208xRDB.h | 1 -
> include/configs/gw_ventana.h | 1 -
> include/configs/km/kmp204x-common.h | 1 -
> include/configs/ls1021aiot.h | 1 -
> include/configs/socfpga_stratix10_socdk.h | 1 -
> include/linux/mtd/cfi.h | 32 +
> include/linux/mtd/spi-nor.h | 419 +++
> include/spi_flash.h | 105 +-
> 120 files changed, 4266 insertions(+), 2058 deletions(-)
> delete mode 100644 doc/SPI/README.dual-flash
> create mode 100644 drivers/mtd/spi/spi-nor-core.c
> create mode 100644 drivers/mtd/spi/spi-nor-ids.c
> create mode 100644 drivers/mtd/spi/spi-nor-tiny.c
> delete mode 100644 drivers/mtd/spi/spi_flash.c
> delete mode 100644 drivers/mtd/spi/spi_flash_ids.c
> create mode 100644 drivers/spi/spi-mem-nodm.c
> create mode 100644 include/linux/mtd/cfi.h
> create mode 100644 include/linux/mtd/spi-nor.h
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2019-01-14 15:02 ` Vignesh R
@ 2019-01-14 15:05 ` Tom Rini
2019-01-21 11:58 ` Vignesh R
1 sibling, 0 replies; 33+ messages in thread
From: Tom Rini @ 2019-01-14 15:05 UTC (permalink / raw)
To: u-boot
On Mon, Jan 14, 2019 at 08:32:29PM +0530, Vignesh R wrote:
> Hi Jagan,
>
> Could you please review v2? If we plan to merge this series for
> v2019.04, we should probably plan to take it a bit early so as to
> address any regression or fall out in time. Thanks!
Yes, please, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190114/3c7622f2/attachment.sig>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2019-01-14 15:02 ` Vignesh R
2019-01-14 15:05 ` Tom Rini
@ 2019-01-21 11:58 ` Vignesh R
2019-01-21 12:10 ` Jagan Teki
1 sibling, 1 reply; 33+ messages in thread
From: Vignesh R @ 2019-01-21 11:58 UTC (permalink / raw)
To: u-boot
On 14/01/19 8:32 PM, Vignesh R wrote:
> Hi Jagan,
>
> Could you please review v2? If we plan to merge this series for
> v2019.04, we should probably plan to take it a bit early so as to
> address any regression or fall out in time. Thanks!
>
Gentle ping... Jagan could you review this series?
If there are no comments, I will address Simon's comments and post v3 tomo.
Regards
Vignesh
> Regards
> Vignesh
>
> On 21/12/18 12:08 PM, Vignesh R wrote:
>> U-Boot SPI NOR support (sf layer) is quite outdated as it does not
>> support 4 byte addressing opcodes, SFDP table parsing and different types of
>> quad mode enable sequences. Many newer flashes no longer support BANK
>> registers used by sf layer to a access >16MB space.
>> Also, many SPI controllers have special MMIO interfaces which provide
>> accelerated read/write access but require knowledge of flash parameters
>> to make use of it. Recent spi-mem layer provides a way to support such
>> flashes but sf layer isn't using that.
>> This patch series syncs SPI NOR framework from Linux v4.19. It also adds
>> spi-mem support on top.
>> So, we gain 4byte addressing support and SFDP support. This makes
>> migrating to U-Boot MTD framework easier.
>>
>> Tested with few Spansion, micron and macronix flashes with TI's dra7xx,
>> k2g, am43xx EVMs. I dont have access to flashes from other vendors. So,
>> I would greatly appreciate testing on other platforms. Complete series
>> with dependencies here[1]
>>
>> For clean build on some platforms, depends on CONFIG_SPI_FLASH migration
>> to defconfigs [2]
>>
>> [1] https://github.com/r-vignesh/u-boot.git branch: spi-nor-mig-patch-v2
>> [2] https://patchwork.ozlabs.org/patch/1007485/
>>
>> Simon, Stefan, Thanks for testing previous versions.
>> I haven't carried Tested-by's here as I have added back SPI_FLASH_BAR
>> support (but isn't enabled by default). Would be great if you could
>> retest this series.
>> I am hoping there won't be any major rework/changes after this round.
>>
>> Change log:
>> Since v1:
>> Remove #ifindef __UBOOT__
>> Add back BAR support, but dont enable as default for all platform (see
>> 10/11 for more details)
>> Enable SPI_FLASH_TINY on boards where there is SPL size constraint as
>> seen on travis ci builds.
>> Drop sf_mtd changes for now as it seems to cause issues.
>> v1: https://patchwork.ozlabs.org/cover/1012146/
>>
>> Since RFC v2:
>> Fix issues reported by Simon Goldschmidt wrt 4 use of byte addressing opcode
>> Fix issues in compiling SFDP code
>> Re organize file names and Makefile to simply spi-nor-tiny inclusion
>> Remove SPI_FLASH_BAR and SF_DUAL_FLASH as these are no longer used
>> RFC v2: https://patchwork.ozlabs.org/cover/1007589/
>>
>> Since RFC v1:
>> Add lightweight SPI flash stack for boards with SPL size constraints
>> Provide non DM version of spi-mem
>> Fix build issues on different platforms as reported by travis-ci on v1
>>
>> RFC v1: https://patchwork.ozlabs.org/cover/1004689/
>>
>> Vignesh R (11):
>> spi-mem: Claim SPI bus before spi mem access
>> spi: Add non DM version of SPI_MEM
>> sh: bitops: add hweight*() macros
>> mtd: spi: Port SPI NOR framework from Linux
>> mtd: spi: Switch to new SPI NOR framework
>> mtd: spi: Remove unused files
>> mtd: spi: Add lightweight SPI flash stack for SPL
>> configs: Enable SPI_FLASH_TINY for resource constrained boards
>> configs: Remove SF_DUAL_FLASH
>> configs: Don't use SPI_FLASH_BAR as default
>> MAINTAINERS: Add an entry for SPI NOR
>>
>> MAINTAINERS | 9 +
>> arch/arm/mach-omap2/am33xx/Kconfig | 1 -
>> arch/sh/include/asm/bitops.h | 4 +
>> common/spl/Kconfig | 21 +-
>> configs/alt_defconfig | 1 -
>> configs/am57xx_evm_defconfig | 1 -
>> configs/am57xx_hs_evm_defconfig | 1 -
>> configs/ap121_defconfig | 1 -
>> configs/ap143_defconfig | 1 -
>> configs/avnet_ultra96_rev1_defconfig | 1 -
>> configs/axm_defconfig | 1 +
>> configs/axs101_defconfig | 1 -
>> configs/axs103_defconfig | 1 -
>> configs/bg0900_defconfig | 1 -
>> configs/blanche_defconfig | 1 -
>> configs/cl-som-am57x_defconfig | 1 -
>> configs/clearfog_defconfig | 1 -
>> configs/cm_t43_defconfig | 1 -
>> configs/da850_am18xxevm_defconfig | 1 +
>> configs/da850evm_nand_defconfig | 2 +-
>> configs/db-88f6820-amc_defconfig | 1 -
>> configs/db-88f6820-gp_defconfig | 1 +
>> configs/display5_defconfig | 1 -
>> configs/display5_factory_defconfig | 1 -
>> configs/dra7xx_evm_defconfig | 1 -
>> configs/dra7xx_hs_evm_defconfig | 1 -
>> configs/ds109_defconfig | 1 -
>> configs/ds414_defconfig | 1 -
>> configs/evb-rv1108_defconfig | 1 -
>> configs/gose_defconfig | 1 -
>> configs/helios4_defconfig | 1 -
>> configs/k2g_evm_defconfig | 1 -
>> configs/k2g_hs_evm_defconfig | 1 -
>> configs/koelsch_defconfig | 1 -
>> configs/lager_defconfig | 1 -
>> configs/maxbcm_defconfig | 1 -
>> configs/mt7629_rfb_defconfig | 1 -
>> configs/mx6sxsabreauto_defconfig | 1 -
>> configs/mx6sxsabresd_defconfig | 1 -
>> configs/mx6ul_14x14_evk_defconfig | 1 -
>> configs/mx6ul_9x9_evk_defconfig | 1 -
>> configs/mx6ull_14x14_evk_defconfig | 1 -
>> configs/mx6ull_14x14_evk_plugin_defconfig | 1 -
>> configs/mx7dsabresd_qspi_defconfig | 1 -
>> configs/porter_defconfig | 2 +-
>> configs/r8a77970_eagle_defconfig | 1 -
>> configs/silk_defconfig | 1 -
>> configs/socfpga_arria5_defconfig | 1 -
>> configs/socfpga_cyclone5_defconfig | 1 -
>> configs/socfpga_is1_defconfig | 1 -
>> configs/socfpga_sockit_defconfig | 1 -
>> configs/socfpga_socrates_defconfig | 1 -
>> configs/socfpga_sr1500_defconfig | 1 -
>> configs/socfpga_stratix10_defconfig | 1 -
>> configs/stout_defconfig | 2 +-
>> configs/taurus_defconfig | 3 +-
>> configs/topic_miami_defconfig | 1 -
>> configs/topic_miamilite_defconfig | 2 -
>> configs/topic_miamiplus_defconfig | 2 -
>> configs/turris_omnia_defconfig | 2 +-
>> configs/xilinx_versal_virt_defconfig | 1 -
>> configs/xilinx_zynqmp_mini_qspi_defconfig | 2 -
>> configs/xilinx_zynqmp_zc1232_revA_defconfig | 2 -
>> configs/xilinx_zynqmp_zc1254_revA_defconfig | 2 -
>> configs/xilinx_zynqmp_zc1275_revA_defconfig | 2 -
>> configs/xilinx_zynqmp_zc1275_revB_defconfig | 2 -
>> .../xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 -
>> .../xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 1 -
>> .../xilinx_zynqmp_zc1751_xm018_dc4_defconfig | 1 -
>> configs/xilinx_zynqmp_zcu100_revC_defconfig | 1 -
>> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 1 -
>> configs/xilinx_zynqmp_zcu102_revA_defconfig | 1 -
>> configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 -
>> configs/xilinx_zynqmp_zcu104_revA_defconfig | 2 -
>> configs/xilinx_zynqmp_zcu104_revC_defconfig | 2 -
>> configs/xilinx_zynqmp_zcu106_revA_defconfig | 2 -
>> configs/xilinx_zynqmp_zcu111_revA_defconfig | 1 -
>> configs/zynq_cc108_defconfig | 1 -
>> configs/zynq_cse_qspi_defconfig | 1 -
>> configs/zynq_dlc20_rev1_0_defconfig | 1 -
>> configs/zynq_microzed_defconfig | 1 -
>> configs/zynq_minized_defconfig | 1 -
>> configs/zynq_z_turn_defconfig | 1 -
>> configs/zynq_zc702_defconfig | 1 -
>> configs/zynq_zc706_defconfig | 1 -
>> configs/zynq_zc770_xm010_defconfig | 1 -
>> configs/zynq_zc770_xm013_defconfig | 1 -
>> configs/zynq_zed_defconfig | 1 -
>> configs/zynq_zybo_defconfig | 1 -
>> configs/zynq_zybo_z7_defconfig | 1 -
>> doc/SPI/README.dual-flash | 92 -
>> doc/SPI/README.ti_qspi_dra_test | 1 -
>> drivers/mtd/spi/Kconfig | 16 +-
>> drivers/mtd/spi/Makefile | 12 +-
>> drivers/mtd/spi/sandbox.c | 36 +-
>> drivers/mtd/spi/sf_dataflash.c | 11 +-
>> drivers/mtd/spi/sf_internal.h | 225 +-
>> drivers/mtd/spi/sf_probe.c | 33 +-
>> drivers/mtd/spi/spi-nor-core.c | 2432 +++++++++++++++++
>> drivers/mtd/spi/spi-nor-ids.c | 297 ++
>> drivers/mtd/spi/spi-nor-tiny.c | 810 ++++++
>> drivers/mtd/spi/spi_flash.c | 1337 ---------
>> drivers/mtd/spi/spi_flash_ids.c | 211 --
>> drivers/spi/Kconfig | 9 +-
>> drivers/spi/Makefile | 1 +
>> drivers/spi/spi-mem-nodm.c | 89 +
>> drivers/spi/spi-mem.c | 6 +
>> drivers/spi/stm32_qspi.c | 4 +-
>> include/configs/T102xQDS.h | 1 -
>> include/configs/T102xRDB.h | 1 -
>> include/configs/T104xRDB.h | 1 -
>> include/configs/T208xQDS.h | 1 -
>> include/configs/T208xRDB.h | 1 -
>> include/configs/gw_ventana.h | 1 -
>> include/configs/km/kmp204x-common.h | 1 -
>> include/configs/ls1021aiot.h | 1 -
>> include/configs/socfpga_stratix10_socdk.h | 1 -
>> include/linux/mtd/cfi.h | 32 +
>> include/linux/mtd/spi-nor.h | 419 +++
>> include/spi_flash.h | 105 +-
>> 120 files changed, 4266 insertions(+), 2058 deletions(-)
>> delete mode 100644 doc/SPI/README.dual-flash
>> create mode 100644 drivers/mtd/spi/spi-nor-core.c
>> create mode 100644 drivers/mtd/spi/spi-nor-ids.c
>> create mode 100644 drivers/mtd/spi/spi-nor-tiny.c
>> delete mode 100644 drivers/mtd/spi/spi_flash.c
>> delete mode 100644 drivers/mtd/spi/spi_flash_ids.c
>> create mode 100644 drivers/spi/spi-mem-nodm.c
>> create mode 100644 include/linux/mtd/cfi.h
>> create mode 100644 include/linux/mtd/spi-nor.h
>>
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot
>
--
Regards
Vignesh
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2019-01-21 11:58 ` Vignesh R
@ 2019-01-21 12:10 ` Jagan Teki
2019-01-21 14:47 ` Vignesh R
0 siblings, 1 reply; 33+ messages in thread
From: Jagan Teki @ 2019-01-21 12:10 UTC (permalink / raw)
To: u-boot
On Mon, Jan 21, 2019 at 5:28 PM Vignesh R <vigneshr@ti.com> wrote:
>
>
>
> On 14/01/19 8:32 PM, Vignesh R wrote:
> > Hi Jagan,
> >
> > Could you please review v2? If we plan to merge this series for
> > v2019.04, we should probably plan to take it a bit early so as to
> > address any regression or fall out in time. Thanks!
> >
>
> Gentle ping... Jagan could you review this series?
> If there are no comments, I will address Simon's comments and post v3 tomo.
Been with DM migration changes, will comment in coming days.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2019-01-21 12:10 ` Jagan Teki
@ 2019-01-21 14:47 ` Vignesh R
2019-01-21 17:08 ` Tom Rini
0 siblings, 1 reply; 33+ messages in thread
From: Vignesh R @ 2019-01-21 14:47 UTC (permalink / raw)
To: u-boot
On 21-Jan-19 5:40 PM, Jagan Teki wrote:
> On Mon, Jan 21, 2019 at 5:28 PM Vignesh R <vigneshr@ti.com> wrote:
>>
>>
>>
>> On 14/01/19 8:32 PM, Vignesh R wrote:
>>> Hi Jagan,
>>>
>>> Could you please review v2? If we plan to merge this series for
>>> v2019.04, we should probably plan to take it a bit early so as to
>>> address any regression or fall out in time. Thanks!
>>>
>>
>> Gentle ping... Jagan could you review this series?
>> If there are no comments, I will address Simon's comments and post v3 tomo.
>
> Been with DM migration changes, will comment in coming days.
Thanks! I would really appreciate if you could consider this series in
time for v2019.04 merge window. This is really blocking further
developments/HW enablements.
There have been at least 3 different patches series just in last couple
weeks [1][2][3], trying to accomplish smaller parts of what this series
does, thus duplicating community efforts.
[1]https://patchwork.ozlabs.org/cover/1025806/
[2]https://patchwork.ozlabs.org/cover/1025167/
[3]https://patchwork.ozlabs.org/patch/1021174/
Also, have received personal pings on whats the state of this series
from few ppl.
Regards
Vignesh
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2019-01-21 14:47 ` Vignesh R
@ 2019-01-21 17:08 ` Tom Rini
2019-01-22 6:25 ` Stefan Roese
0 siblings, 1 reply; 33+ messages in thread
From: Tom Rini @ 2019-01-21 17:08 UTC (permalink / raw)
To: u-boot
On Mon, Jan 21, 2019 at 08:17:31PM +0530, Vignesh R wrote:
>
>
> On 21-Jan-19 5:40 PM, Jagan Teki wrote:
> > On Mon, Jan 21, 2019 at 5:28 PM Vignesh R <vigneshr@ti.com> wrote:
> >>
> >>
> >>
> >> On 14/01/19 8:32 PM, Vignesh R wrote:
> >>> Hi Jagan,
> >>>
> >>> Could you please review v2? If we plan to merge this series for
> >>> v2019.04, we should probably plan to take it a bit early so as to
> >>> address any regression or fall out in time. Thanks!
> >>>
> >>
> >> Gentle ping... Jagan could you review this series?
> >> If there are no comments, I will address Simon's comments and post v3 tomo.
> >
> > Been with DM migration changes, will comment in coming days.
>
> Thanks! I would really appreciate if you could consider this series in
> time for v2019.04 merge window. This is really blocking further
> developments/HW enablements.
> There have been at least 3 different patches series just in last couple
> weeks [1][2][3], trying to accomplish smaller parts of what this series
> does, thus duplicating community efforts.
>
> [1]https://patchwork.ozlabs.org/cover/1025806/
> [2]https://patchwork.ozlabs.org/cover/1025167/
> [3]https://patchwork.ozlabs.org/patch/1021174/
>
> Also, have received personal pings on whats the state of this series
> from few ppl.
I really want to see this in for v2019.04 as well, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190121/66410ab2/attachment.sig>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
` (13 preceding siblings ...)
2019-01-14 15:02 ` Vignesh R
@ 2019-01-21 17:14 ` Horatiu Vultur
14 siblings, 0 replies; 33+ messages in thread
From: Horatiu Vultur @ 2019-01-21 17:14 UTC (permalink / raw)
To: u-boot
Hi Vignesh,
I have done few small tests on Ocelot and Luton boards which have
SPI NOR: mx25l25635f and m25p128. I have not seen any issues. So
if you want, you can add:
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
The 12/21/2018 12:08, Vignesh R wrote:
> U-Boot SPI NOR support (sf layer) is quite outdated as it does not
> support 4 byte addressing opcodes, SFDP table parsing and different types of
> quad mode enable sequences. Many newer flashes no longer support BANK
> registers used by sf layer to a access >16MB space.
> Also, many SPI controllers have special MMIO interfaces which provide
> accelerated read/write access but require knowledge of flash parameters
> to make use of it. Recent spi-mem layer provides a way to support such
> flashes but sf layer isn't using that.
> This patch series syncs SPI NOR framework from Linux v4.19. It also adds
> spi-mem support on top.
> So, we gain 4byte addressing support and SFDP support. This makes
> migrating to U-Boot MTD framework easier.
>
> Tested with few Spansion, micron and macronix flashes with TI's dra7xx,
> k2g, am43xx EVMs. I dont have access to flashes from other vendors. So,
> I would greatly appreciate testing on other platforms. Complete series
> with dependencies here[1]
>
> For clean build on some platforms, depends on CONFIG_SPI_FLASH migration
> to defconfigs [2]
>
> [1] https://github.com/r-vignesh/u-boot.git branch: spi-nor-mig-patch-v2
> [2] https://patchwork.ozlabs.org/patch/1007485/
>
> Simon, Stefan, Thanks for testing previous versions.
> I haven't carried Tested-by's here as I have added back SPI_FLASH_BAR
> support (but isn't enabled by default). Would be great if you could
> retest this series.
> I am hoping there won't be any major rework/changes after this round.
>
> Change log:
> Since v1:
> Remove #ifindef __UBOOT__
> Add back BAR support, but dont enable as default for all platform (see
> 10/11 for more details)
> Enable SPI_FLASH_TINY on boards where there is SPL size constraint as
> seen on travis ci builds.
> Drop sf_mtd changes for now as it seems to cause issues.
> v1: https://patchwork.ozlabs.org/cover/1012146/
>
> Since RFC v2:
> Fix issues reported by Simon Goldschmidt wrt 4 use of byte addressing opcode
> Fix issues in compiling SFDP code
> Re organize file names and Makefile to simply spi-nor-tiny inclusion
> Remove SPI_FLASH_BAR and SF_DUAL_FLASH as these are no longer used
> RFC v2: https://patchwork.ozlabs.org/cover/1007589/
>
> Since RFC v1:
> Add lightweight SPI flash stack for boards with SPL size constraints
> Provide non DM version of spi-mem
> Fix build issues on different platforms as reported by travis-ci on v1
>
> RFC v1: https://patchwork.ozlabs.org/cover/1004689/
>
> Vignesh R (11):
> spi-mem: Claim SPI bus before spi mem access
> spi: Add non DM version of SPI_MEM
> sh: bitops: add hweight*() macros
> mtd: spi: Port SPI NOR framework from Linux
> mtd: spi: Switch to new SPI NOR framework
> mtd: spi: Remove unused files
> mtd: spi: Add lightweight SPI flash stack for SPL
> configs: Enable SPI_FLASH_TINY for resource constrained boards
> configs: Remove SF_DUAL_FLASH
> configs: Don't use SPI_FLASH_BAR as default
> MAINTAINERS: Add an entry for SPI NOR
>
> MAINTAINERS | 9 +
> arch/arm/mach-omap2/am33xx/Kconfig | 1 -
> arch/sh/include/asm/bitops.h | 4 +
> common/spl/Kconfig | 21 +-
> configs/alt_defconfig | 1 -
> configs/am57xx_evm_defconfig | 1 -
> configs/am57xx_hs_evm_defconfig | 1 -
> configs/ap121_defconfig | 1 -
> configs/ap143_defconfig | 1 -
> configs/avnet_ultra96_rev1_defconfig | 1 -
> configs/axm_defconfig | 1 +
> configs/axs101_defconfig | 1 -
> configs/axs103_defconfig | 1 -
> configs/bg0900_defconfig | 1 -
> configs/blanche_defconfig | 1 -
> configs/cl-som-am57x_defconfig | 1 -
> configs/clearfog_defconfig | 1 -
> configs/cm_t43_defconfig | 1 -
> configs/da850_am18xxevm_defconfig | 1 +
> configs/da850evm_nand_defconfig | 2 +-
> configs/db-88f6820-amc_defconfig | 1 -
> configs/db-88f6820-gp_defconfig | 1 +
> configs/display5_defconfig | 1 -
> configs/display5_factory_defconfig | 1 -
> configs/dra7xx_evm_defconfig | 1 -
> configs/dra7xx_hs_evm_defconfig | 1 -
> configs/ds109_defconfig | 1 -
> configs/ds414_defconfig | 1 -
> configs/evb-rv1108_defconfig | 1 -
> configs/gose_defconfig | 1 -
> configs/helios4_defconfig | 1 -
> configs/k2g_evm_defconfig | 1 -
> configs/k2g_hs_evm_defconfig | 1 -
> configs/koelsch_defconfig | 1 -
> configs/lager_defconfig | 1 -
> configs/maxbcm_defconfig | 1 -
> configs/mt7629_rfb_defconfig | 1 -
> configs/mx6sxsabreauto_defconfig | 1 -
> configs/mx6sxsabresd_defconfig | 1 -
> configs/mx6ul_14x14_evk_defconfig | 1 -
> configs/mx6ul_9x9_evk_defconfig | 1 -
> configs/mx6ull_14x14_evk_defconfig | 1 -
> configs/mx6ull_14x14_evk_plugin_defconfig | 1 -
> configs/mx7dsabresd_qspi_defconfig | 1 -
> configs/porter_defconfig | 2 +-
> configs/r8a77970_eagle_defconfig | 1 -
> configs/silk_defconfig | 1 -
> configs/socfpga_arria5_defconfig | 1 -
> configs/socfpga_cyclone5_defconfig | 1 -
> configs/socfpga_is1_defconfig | 1 -
> configs/socfpga_sockit_defconfig | 1 -
> configs/socfpga_socrates_defconfig | 1 -
> configs/socfpga_sr1500_defconfig | 1 -
> configs/socfpga_stratix10_defconfig | 1 -
> configs/stout_defconfig | 2 +-
> configs/taurus_defconfig | 3 +-
> configs/topic_miami_defconfig | 1 -
> configs/topic_miamilite_defconfig | 2 -
> configs/topic_miamiplus_defconfig | 2 -
> configs/turris_omnia_defconfig | 2 +-
> configs/xilinx_versal_virt_defconfig | 1 -
> configs/xilinx_zynqmp_mini_qspi_defconfig | 2 -
> configs/xilinx_zynqmp_zc1232_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1254_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1275_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zc1275_revB_defconfig | 2 -
> .../xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 1 -
> .../xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 1 -
> .../xilinx_zynqmp_zc1751_xm018_dc4_defconfig | 1 -
> configs/xilinx_zynqmp_zcu100_revC_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_revA_defconfig | 1 -
> configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 -
> configs/xilinx_zynqmp_zcu104_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zcu104_revC_defconfig | 2 -
> configs/xilinx_zynqmp_zcu106_revA_defconfig | 2 -
> configs/xilinx_zynqmp_zcu111_revA_defconfig | 1 -
> configs/zynq_cc108_defconfig | 1 -
> configs/zynq_cse_qspi_defconfig | 1 -
> configs/zynq_dlc20_rev1_0_defconfig | 1 -
> configs/zynq_microzed_defconfig | 1 -
> configs/zynq_minized_defconfig | 1 -
> configs/zynq_z_turn_defconfig | 1 -
> configs/zynq_zc702_defconfig | 1 -
> configs/zynq_zc706_defconfig | 1 -
> configs/zynq_zc770_xm010_defconfig | 1 -
> configs/zynq_zc770_xm013_defconfig | 1 -
> configs/zynq_zed_defconfig | 1 -
> configs/zynq_zybo_defconfig | 1 -
> configs/zynq_zybo_z7_defconfig | 1 -
> doc/SPI/README.dual-flash | 92 -
> doc/SPI/README.ti_qspi_dra_test | 1 -
> drivers/mtd/spi/Kconfig | 16 +-
> drivers/mtd/spi/Makefile | 12 +-
> drivers/mtd/spi/sandbox.c | 36 +-
> drivers/mtd/spi/sf_dataflash.c | 11 +-
> drivers/mtd/spi/sf_internal.h | 225 +-
> drivers/mtd/spi/sf_probe.c | 33 +-
> drivers/mtd/spi/spi-nor-core.c | 2432 +++++++++++++++++
> drivers/mtd/spi/spi-nor-ids.c | 297 ++
> drivers/mtd/spi/spi-nor-tiny.c | 810 ++++++
> drivers/mtd/spi/spi_flash.c | 1337 ---------
> drivers/mtd/spi/spi_flash_ids.c | 211 --
> drivers/spi/Kconfig | 9 +-
> drivers/spi/Makefile | 1 +
> drivers/spi/spi-mem-nodm.c | 89 +
> drivers/spi/spi-mem.c | 6 +
> drivers/spi/stm32_qspi.c | 4 +-
> include/configs/T102xQDS.h | 1 -
> include/configs/T102xRDB.h | 1 -
> include/configs/T104xRDB.h | 1 -
> include/configs/T208xQDS.h | 1 -
> include/configs/T208xRDB.h | 1 -
> include/configs/gw_ventana.h | 1 -
> include/configs/km/kmp204x-common.h | 1 -
> include/configs/ls1021aiot.h | 1 -
> include/configs/socfpga_stratix10_socdk.h | 1 -
> include/linux/mtd/cfi.h | 32 +
> include/linux/mtd/spi-nor.h | 419 +++
> include/spi_flash.h | 105 +-
> 120 files changed, 4266 insertions(+), 2058 deletions(-)
> delete mode 100644 doc/SPI/README.dual-flash
> create mode 100644 drivers/mtd/spi/spi-nor-core.c
> create mode 100644 drivers/mtd/spi/spi-nor-ids.c
> create mode 100644 drivers/mtd/spi/spi-nor-tiny.c
> delete mode 100644 drivers/mtd/spi/spi_flash.c
> delete mode 100644 drivers/mtd/spi/spi_flash_ids.c
> create mode 100644 drivers/spi/spi-mem-nodm.c
> create mode 100644 include/linux/mtd/cfi.h
> create mode 100644 include/linux/mtd/spi-nor.h
>
> --
> 2.20.1
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot
--
/Horatiu
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework
2019-01-21 17:08 ` Tom Rini
@ 2019-01-22 6:25 ` Stefan Roese
0 siblings, 0 replies; 33+ messages in thread
From: Stefan Roese @ 2019-01-22 6:25 UTC (permalink / raw)
To: u-boot
On 21.01.19 18:08, Tom Rini wrote:
> On Mon, Jan 21, 2019 at 08:17:31PM +0530, Vignesh R wrote:
>>
>>
>> On 21-Jan-19 5:40 PM, Jagan Teki wrote:
>>> On Mon, Jan 21, 2019 at 5:28 PM Vignesh R <vigneshr@ti.com> wrote:
>>>>
>>>>
>>>>
>>>> On 14/01/19 8:32 PM, Vignesh R wrote:
>>>>> Hi Jagan,
>>>>>
>>>>> Could you please review v2? If we plan to merge this series for
>>>>> v2019.04, we should probably plan to take it a bit early so as to
>>>>> address any regression or fall out in time. Thanks!
>>>>>
>>>>
>>>> Gentle ping... Jagan could you review this series?
>>>> If there are no comments, I will address Simon's comments and post v3 tomo.
>>>
>>> Been with DM migration changes, will comment in coming days.
>>
>> Thanks! I would really appreciate if you could consider this series in
>> time for v2019.04 merge window. This is really blocking further
>> developments/HW enablements.
>> There have been at least 3 different patches series just in last couple
>> weeks [1][2][3], trying to accomplish smaller parts of what this series
>> does, thus duplicating community efforts.
>>
>> [1]https://patchwork.ozlabs.org/cover/1025806/
>> [2]https://patchwork.ozlabs.org/cover/1025167/
>> [3]https://patchwork.ozlabs.org/patch/1021174/
>>
>> Also, have received personal pings on whats the state of this series
>> from few ppl.
>
> I really want to see this in for v2019.04 as well, thanks!
Full ack. We really should integrate this patchset soon in this
release cycle, so that many people can test it on their hardware.
Thanks,
Stefan
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 09/11] configs: Remove SF_DUAL_FLASH
2018-12-21 6:38 ` [U-Boot] [PATCH v2 09/11] configs: Remove SF_DUAL_FLASH Vignesh R
@ 2019-01-25 14:47 ` Jagan Teki
2019-01-25 15:01 ` Vignesh R
0 siblings, 1 reply; 33+ messages in thread
From: Jagan Teki @ 2019-01-25 14:47 UTC (permalink / raw)
To: u-boot
On Fri, Dec 21, 2018 at 12:18 PM Vignesh R <vigneshr@ti.com> wrote:
>
> SF_DUAL_FLASH claims to enable support for SF_DUAL_STACKED_FLASH and
> SF_DUAL_PARALLEL_FLASH. But, in current U-Boot code, grepping for above
> enums yield no user and therefore support seems to be incomplete. Remove
> these configs so as to avoid confusion.
So, with Linux sync. all dual flash code is dropped is it?
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 09/11] configs: Remove SF_DUAL_FLASH
2019-01-25 14:47 ` Jagan Teki
@ 2019-01-25 15:01 ` Vignesh R
2019-01-28 6:36 ` Jagan Teki
0 siblings, 1 reply; 33+ messages in thread
From: Vignesh R @ 2019-01-25 15:01 UTC (permalink / raw)
To: u-boot
On 25/01/19 8:17 PM, Jagan Teki wrote:
> On Fri, Dec 21, 2018 at 12:18 PM Vignesh R <vigneshr@ti.com> wrote:
>>
>> SF_DUAL_FLASH claims to enable support for SF_DUAL_STACKED_FLASH and
>> SF_DUAL_PARALLEL_FLASH. But, in current U-Boot code, grepping for above
>> enums yield no user and therefore support seems to be incomplete. Remove
>> these configs so as to avoid confusion.
>
> So, with Linux sync. all dual flash code is dropped is it?
>
Yes, because Linux does not support dual flash. I did try to add back
dual flash support, but could not find any SPI flash claiming
SF_DUAL_FLASH capability in today's U-Boot code. Therefore, this patch
just drops the CONFIG option.
Dual flash can always be added back to this framework when there is an
actual user of the code in _mainline_ U-Boot.
--
Regards
Vignesh
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 04/11] mtd: spi: Port SPI NOR framework from Linux
2018-12-21 6:38 ` [U-Boot] [PATCH v2 04/11] mtd: spi: Port SPI NOR framework from Linux Vignesh R
@ 2019-01-27 18:48 ` Jagan Teki
2019-01-28 11:43 ` Vignesh R
0 siblings, 1 reply; 33+ messages in thread
From: Jagan Teki @ 2019-01-27 18:48 UTC (permalink / raw)
To: u-boot
Do you have this whole series in some branch in github? I'm unable to
apply it on master.
On Fri, Dec 21, 2018 at 12:15 PM Vignesh R <vigneshr@ti.com> wrote:
>
> Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
> support 4 byte addressing opcodes, SFDP table parsing and different types of
> quad mode enable sequences. Many newer flashes no longer support BANK
> registers used by sf layer to a access >16MB space.
> Also, many SPI controllers have special MMIO interfaces which provide
> accelerated read/write access but require knowledge of flash parameters
> to make use of it. Recent spi-mem layer provides a way to support such
> flashes but sf layer isn't using that.
> So sync SPI NOR framework from Linux v4.19 and add spi-mem support on top.
> in order to gain 4 byte addressing support, SFDP support and a way to
> support SPI controllers with MMIO flash interface.
Understand the usage if direct complete sync, however it's difficult
for me to review whole stuff. Can you please break into few patches
like Basic sync, SFDP and other.
>
> Signed-off-by: Vignesh R <vigneshr@ti.com>
> ---
> drivers/mtd/spi/spi-nor-core.c | 2590 ++++++++++++++++++++++++++++++++
> include/linux/mtd/cfi.h | 32 +
> include/linux/mtd/spi-nor.h | 410 +++++
> 3 files changed, 3032 insertions(+)
> create mode 100644 drivers/mtd/spi/spi-nor-core.c
> create mode 100644 include/linux/mtd/cfi.h
> create mode 100644 include/linux/mtd/spi-nor.h
>
> diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c
> new file mode 100644
> index 000000000000..597898d3b4af
> --- /dev/null
> +++ b/drivers/mtd/spi/spi-nor-core.c
> @@ -0,0 +1,2590 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Based on m25p80.c, by Mike Lavender (mike at steroidmicros.com), with
> + * influence from lart.c (Abraham Van Der Merwe) and mtd_dataflash.c
> + *
> + * Copyright (C) 2005, Intec Automation Inc.
> + * Copyright (C) 2014, Freescale Semiconductor, Inc.
> + *
> + * Synced from Linux v4.19
> + */
> +
> +#include <common.h>
> +#include <linux/err.h>
> +#include <linux/errno.h>
> +#include <linux/log2.h>
> +#include <linux/math64.h>
> +#include <linux/sizes.h>
> +
> +#include <linux/mtd/mtd.h>
> +#include <linux/mtd/spi-nor.h>
> +#include <spi-mem.h>
> +#include <spi.h>
> +
> +/* Define max times to check status register before we give up. */
> +
> +/*
> + * For everything but full-chip erase; probably could be much smaller, but kept
> + * around for safety for now
> + */
> +
> +#define HZ CONFIG_SYS_HZ
> +
> +#define DEFAULT_READY_WAIT_JIFFIES (40UL * HZ)
> +
> +#define SPI_NOR_MAX_ID_LEN 6
> +#define SPI_NOR_MAX_ADDR_WIDTH 4
> +
> +struct flash_info {
> + char *name;
> +
> + /*
> + * This array stores the ID bytes.
> + * The first three bytes are the JEDIC ID.
> + * JEDEC ID zero means "no ID" (mostly older chips).
> + */
> + u8 id[SPI_NOR_MAX_ID_LEN];
> + u8 id_len;
> +
> + /* The size listed here is what works with SPINOR_OP_SE, which isn't
> + * necessarily called a "sector" by the vendor.
> + */
> + unsigned int sector_size;
> + u16 n_sectors;
> +
> + u16 page_size;
> + u16 addr_width;
> +
> + u16 flags;
> +#define SECT_4K BIT(0) /* SPINOR_OP_BE_4K works uniformly */
> +#define SPI_NOR_NO_ERASE BIT(1) /* No erase command needed */
> +#define SST_WRITE BIT(2) /* use SST byte programming */
> +#define SPI_NOR_NO_FR BIT(3) /* Can't do fastread */
> +#define SECT_4K_PMC BIT(4) /* SPINOR_OP_BE_4K_PMC works uniformly */
> +#define SPI_NOR_DUAL_READ BIT(5) /* Flash supports Dual Read */
> +#define SPI_NOR_QUAD_READ BIT(6) /* Flash supports Quad Read */
> +#define USE_FSR BIT(7) /* use flag status register */
> +#define SPI_NOR_HAS_LOCK BIT(8) /* Flash supports lock/unlock via SR */
> +#define SPI_NOR_HAS_TB BIT(9) /*
> + * Flash SR has Top/Bottom (TB) protect
> + * bit. Must be used with
> + * SPI_NOR_HAS_LOCK.
> + */
> +#define SPI_S3AN BIT(10) /*
> + * Xilinx Spartan 3AN In-System Flash
> + * (MFR cannot be used for probing
> + * because it has the same value as
> + * ATMEL flashes)
> + */
> +#define SPI_NOR_4B_OPCODES BIT(11) /*
> + * Use dedicated 4byte address op codes
> + * to support memory size above 128Mib.
> + */
> +#define NO_CHIP_ERASE BIT(12) /* Chip does not support chip erase */
> +#define SPI_NOR_SKIP_SFDP BIT(13) /* Skip parsing of SFDP tables */
> +#define USE_CLSR BIT(14) /* use CLSR command */
> +
> + int (*quad_enable)(struct spi_nor *nor);
> +};
> +
> +#define JEDEC_MFR(info) ((info)->id[0])
> +
> +static int spi_nor_read_write_reg(struct spi_nor *nor, struct spi_mem_op
> + *op, void *buf)
> +{
> + if (op->data.dir == SPI_MEM_DATA_IN)
> + op->data.buf.in = buf;
> + else
> + op->data.buf.out = buf;
> + return spi_mem_exec_op(nor->spi, op);
> +}
> +
> +static int spi_nor_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len)
> +{
> + struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(code, 1),
> + SPI_MEM_OP_NO_ADDR,
> + SPI_MEM_OP_NO_DUMMY,
> + SPI_MEM_OP_DATA_IN(len, NULL, 1));
> + int ret;
> +
> + ret = spi_nor_read_write_reg(nor, &op, val);
> + if (ret < 0)
> + dev_dbg(&flash->spimem->spi->dev, "error %d reading %x\n", ret,
> + code);
> +
> + return ret;
> +}
> +
> +static int spi_nor_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
> +{
> + struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(opcode, 1),
> + SPI_MEM_OP_NO_ADDR,
> + SPI_MEM_OP_NO_DUMMY,
> + SPI_MEM_OP_DATA_OUT(len, NULL, 1));
> +
> + return spi_nor_read_write_reg(nor, &op, buf);
> +}
> +
> +static ssize_t spi_nor_read_data(struct spi_nor *nor, loff_t from, size_t len,
> + u_char *buf)
> +{
> + struct spi_mem_op op =
> + SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 1),
> + SPI_MEM_OP_ADDR(nor->addr_width, from, 1),
> + SPI_MEM_OP_DUMMY(nor->read_dummy, 1),
> + SPI_MEM_OP_DATA_IN(len, buf, 1));
> + size_t remaining = len;
> + int ret;
> +
> + /* get transfer protocols. */
> + op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->read_proto);
> + op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->read_proto);
> + op.dummy.buswidth = op.addr.buswidth;
> + op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->read_proto);
> +
> + /* convert the dummy cycles to the number of bytes */
> + op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
> +
> + while (remaining) {
> + op.data.nbytes = remaining < UINT_MAX ? remaining : UINT_MAX;
> + ret = spi_mem_adjust_op_size(nor->spi, &op);
> + if (ret)
> + return ret;
> +
> + ret = spi_mem_exec_op(nor->spi, &op);
> + if (ret)
> + return ret;
> +
> + op.addr.val += op.data.nbytes;
> + remaining -= op.data.nbytes;
> + op.data.buf.in += op.data.nbytes;
> + }
> +
> + return len;
> +}
> +
> +static ssize_t spi_nor_write_data(struct spi_nor *nor, loff_t to, size_t len,
> + const u_char *buf)
> +{
> + struct spi_mem_op op =
> + SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 1),
> + SPI_MEM_OP_ADDR(nor->addr_width, to, 1),
> + SPI_MEM_OP_NO_DUMMY,
> + SPI_MEM_OP_DATA_OUT(len, buf, 1));
> + size_t remaining = len;
> + int ret;
> +
> + /* get transfer protocols. */
> + op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->write_proto);
> + op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->write_proto);
> + op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->write_proto);
> +
> + if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second)
> + op.addr.nbytes = 0;
> +
> + while (remaining) {
> + op.data.nbytes = remaining < UINT_MAX ? remaining : UINT_MAX;
> + ret = spi_mem_adjust_op_size(nor->spi, &op);
> + if (ret)
> + return ret;
> +
> + ret = spi_mem_exec_op(nor->spi, &op);
> + if (ret)
> + return ret;
> +
> + op.addr.val += op.data.nbytes;
> + remaining -= op.data.nbytes;
> + op.data.buf.out += op.data.nbytes;
> + }
> +
> + return len;
> +}
> +
> +/*
> + * Read the status register, returning its value in the location
> + * Return the status register value.
> + * Returns negative if error occurred.
> + */
> +static int read_sr(struct spi_nor *nor)
> +{
> + int ret;
> + u8 val;
> +
> + ret = nor->read_reg(nor, SPINOR_OP_RDSR, &val, 1);
> + if (ret < 0) {
> + pr_debug("error %d reading SR\n", (int)ret);
> + return ret;
> + }
> +
> + return val;
> +}
> +
> +/*
> + * Read the flag status register, returning its value in the location
> + * Return the status register value.
> + * Returns negative if error occurred.
> + */
> +static int read_fsr(struct spi_nor *nor)
> +{
> + int ret;
> + u8 val;
> +
> + ret = nor->read_reg(nor, SPINOR_OP_RDFSR, &val, 1);
> + if (ret < 0) {
> + pr_debug("error %d reading FSR\n", ret);
> + return ret;
> + }
> +
> + return val;
> +}
> +
> +/*
> + * Read configuration register, returning its value in the
> + * location. Return the configuration register value.
> + * Returns negative if error occurred.
> + */
> +#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
> +static int read_cr(struct spi_nor *nor)
> +{
> + int ret;
> + u8 val;
> +
> + ret = nor->read_reg(nor, SPINOR_OP_RDCR, &val, 1);
> + if (ret < 0) {
> + dev_dbg(nor->dev, "error %d reading CR\n", ret);
> + return ret;
> + }
> +
> + return val;
> +}
> +#endif
> +
> +/*
> + * Write status register 1 byte
> + * Returns negative if error occurred.
> + */
> +static int write_sr(struct spi_nor *nor, u8 val)
> +{
> + nor->cmd_buf[0] = val;
> + return nor->write_reg(nor, SPINOR_OP_WRSR, nor->cmd_buf, 1);
> +}
> +
> +/*
> + * Set write enable latch with Write Enable command.
> + * Returns negative if error occurred.
> + */
> +static int write_enable(struct spi_nor *nor)
> +{
> + return nor->write_reg(nor, SPINOR_OP_WREN, NULL, 0);
> +}
> +
> +/*
> + * Send write disable instruction to the chip.
> + */
> +static int write_disable(struct spi_nor *nor)
> +{
> + return nor->write_reg(nor, SPINOR_OP_WRDI, NULL, 0);
> +}
> +
> +static struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd)
> +{
> + return mtd->priv;
> +}
> +
> +static u8 spi_nor_convert_opcode(u8 opcode, const u8 table[][2], size_t size)
> +{
> + size_t i;
> +
> + for (i = 0; i < size; i++)
> + if (table[i][0] == opcode)
> + return table[i][1];
> +
> + /* No conversion found, keep input op code. */
> + return opcode;
> +}
> +
> +static u8 spi_nor_convert_3to4_read(u8 opcode)
> +{
> + static const u8 spi_nor_3to4_read[][2] = {
> + { SPINOR_OP_READ, SPINOR_OP_READ_4B },
> + { SPINOR_OP_READ_FAST, SPINOR_OP_READ_FAST_4B },
> + { SPINOR_OP_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B },
> + { SPINOR_OP_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B },
> + { SPINOR_OP_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B },
> + { SPINOR_OP_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B },
> +
> + { SPINOR_OP_READ_1_1_1_DTR, SPINOR_OP_READ_1_1_1_DTR_4B },
> + { SPINOR_OP_READ_1_2_2_DTR, SPINOR_OP_READ_1_2_2_DTR_4B },
> + { SPINOR_OP_READ_1_4_4_DTR, SPINOR_OP_READ_1_4_4_DTR_4B },
> + };
> +
> + return spi_nor_convert_opcode(opcode, spi_nor_3to4_read,
> + ARRAY_SIZE(spi_nor_3to4_read));
> +}
> +
> +static u8 spi_nor_convert_3to4_program(u8 opcode)
> +{
> + static const u8 spi_nor_3to4_program[][2] = {
> + { SPINOR_OP_PP, SPINOR_OP_PP_4B },
> + { SPINOR_OP_PP_1_1_4, SPINOR_OP_PP_1_1_4_4B },
> + { SPINOR_OP_PP_1_4_4, SPINOR_OP_PP_1_4_4_4B },
> + };
> +
> + return spi_nor_convert_opcode(opcode, spi_nor_3to4_program,
> + ARRAY_SIZE(spi_nor_3to4_program));
> +}
> +
> +static u8 spi_nor_convert_3to4_erase(u8 opcode)
> +{
> + static const u8 spi_nor_3to4_erase[][2] = {
> + { SPINOR_OP_BE_4K, SPINOR_OP_BE_4K_4B },
> + { SPINOR_OP_BE_32K, SPINOR_OP_BE_32K_4B },
> + { SPINOR_OP_SE, SPINOR_OP_SE_4B },
> + };
> +
> + return spi_nor_convert_opcode(opcode, spi_nor_3to4_erase,
> + ARRAY_SIZE(spi_nor_3to4_erase));
> +}
> +
> +static void spi_nor_set_4byte_opcodes(struct spi_nor *nor,
> + const struct flash_info *info)
> +{
> + /* Do some manufacturer fixups first */
> + switch (JEDEC_MFR(info)) {
> + case SNOR_MFR_SPANSION:
> + /* No small sector erase for 4-byte command set */
> + nor->erase_opcode = SPINOR_OP_SE;
> + nor->mtd.erasesize = info->sector_size;
> + break;
> +
> + default:
> + break;
> + }
> +
> + nor->read_opcode = spi_nor_convert_3to4_read(nor->read_opcode);
> + nor->program_opcode = spi_nor_convert_3to4_program(nor->program_opcode);
> + nor->erase_opcode = spi_nor_convert_3to4_erase(nor->erase_opcode);
> +}
> +
> +/* Enable/disable 4-byte addressing mode. */
> +static int set_4byte(struct spi_nor *nor, const struct flash_info *info,
> + int enable)
> +{
> + int status;
> + bool need_wren = false;
> + u8 cmd;
> +
> + switch (JEDEC_MFR(info)) {
> + case SNOR_MFR_ST:
> + case SNOR_MFR_MICRON:
> + /* Some Micron need WREN command; all will accept it */
> + need_wren = true;
> + case SNOR_MFR_MACRONIX:
> + case SNOR_MFR_WINBOND:
> + if (need_wren)
> + write_enable(nor);
> +
> + cmd = enable ? SPINOR_OP_EN4B : SPINOR_OP_EX4B;
> + status = nor->write_reg(nor, cmd, NULL, 0);
> + if (need_wren)
> + write_disable(nor);
> +
> + if (!status && !enable &&
> + JEDEC_MFR(info) == SNOR_MFR_WINBOND) {
> + /*
> + * On Winbond W25Q256FV, leaving 4byte mode causes
> + * the Extended Address Register to be set to 1, so all
> + * 3-byte-address reads come from the second 16M.
> + * We must clear the register to enable normal behavior.
> + */
> + write_enable(nor);
> + nor->cmd_buf[0] = 0;
> + nor->write_reg(nor, SPINOR_OP_WREAR, nor->cmd_buf, 1);
> + write_disable(nor);
> + }
> +
> + return status;
> + default:
> + /* Spansion style */
> + nor->cmd_buf[0] = enable << 7;
> + return nor->write_reg(nor, SPINOR_OP_BRWR, nor->cmd_buf, 1);
> + }
> +}
> +
> +static int spi_nor_sr_ready(struct spi_nor *nor)
> +{
> + int sr = read_sr(nor);
> +
> + if (sr < 0)
> + return sr;
> +
> +#ifndef CONFIG_SPL_BUILD
> + if (nor->flags & SNOR_F_USE_CLSR && sr & (SR_E_ERR | SR_P_ERR)) {
> + if (sr & SR_E_ERR)
> + dev_dbg(nor->dev, "Erase Error occurred\n");
> + else
> + dev_dbg(nor->dev, "Programming Error occurred\n");
> +
> + nor->write_reg(nor, SPINOR_OP_CLSR, NULL, 0);
> + return -EIO;
> + }
> +#endif
Does it increase SPL size? or do we always assume SPL can't access
flash that would require CLSR?
> +
> + return !(sr & SR_WIP);
> +}
> +
> +static int spi_nor_fsr_ready(struct spi_nor *nor)
> +{
> + int fsr = read_fsr(nor);
> +
> + if (fsr < 0)
> + return fsr;
> +#ifndef CONFIG_SPL_BUILD
> + if (fsr & (FSR_E_ERR | FSR_P_ERR)) {
> + if (fsr & FSR_E_ERR)
> + dev_dbg(nor->dev, "Erase operation failed.\n");
> + else
> + dev_dbg(nor->dev, "Program operation failed.\n");
> +
> + if (fsr & FSR_PT_ERR)
> + dev_dbg(nor->dev,
> + "Attempted to modify a protected sector.\n");
> +
> + nor->write_reg(nor, SPINOR_OP_CLFSR, NULL, 0);
> + return -EIO;
> + }
> +#endif
> + return fsr & FSR_READY;
> +}
> +
> +static int spi_nor_ready(struct spi_nor *nor)
> +{
> + int sr, fsr;
> +
> + sr = spi_nor_sr_ready(nor);
> + if (sr < 0)
> + return sr;
> + fsr = nor->flags & SNOR_F_USE_FSR ? spi_nor_fsr_ready(nor) : 1;
> + if (fsr < 0)
> + return fsr;
> + return sr && fsr;
> +}
> +
> +/*
> + * Service routine to read status register until ready, or timeout occurs.
> + * Returns non-zero if error.
> + */
> +static int spi_nor_wait_till_ready_with_timeout(struct spi_nor *nor,
> + unsigned long timeout)
> +{
> + unsigned long timebase;
> + int ret;
> +
> + timebase = get_timer(0);
> +
> + while (get_timer(timebase) < timeout) {
> + ret = spi_nor_ready(nor);
> + if (ret < 0)
> + return ret;
> + if (ret)
> + return 0;
> + }
> +
> + dev_err(nor->dev, "flash operation timed out\n");
> +
> + return -ETIMEDOUT;
> +}
> +
> +static int spi_nor_wait_till_ready(struct spi_nor *nor)
> +{
> + return spi_nor_wait_till_ready_with_timeout(nor,
> + DEFAULT_READY_WAIT_JIFFIES);
> +}
> +
> +/*
> + * Initiate the erasure of a single sector
> + */
> +static int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
> +{
> + u8 buf[SPI_NOR_MAX_ADDR_WIDTH];
> + int i;
> +
> + if (nor->erase)
> + return nor->erase(nor, addr);
> +
> + /*
> + * Default implementation, if driver doesn't have a specialized HW
> + * control
> + */
> + for (i = nor->addr_width - 1; i >= 0; i--) {
> + buf[i] = addr & 0xff;
> + addr >>= 8;
> + }
> +
> + return nor->write_reg(nor, nor->erase_opcode, buf, nor->addr_width);
> +}
> +
> +/*
> + * Erase an address range on the nor chip. The address range may extend
> + * one or more erase sectors. Return an error is there is a problem erasing.
> + */
> +static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
> +{
> + struct spi_nor *nor = mtd_to_spi_nor(mtd);
> + u32 addr, len, rem;
> + int ret;
> +
> + dev_dbg(nor->dev, "at 0x%llx, len %lld\n", (long long)instr->addr,
> + (long long)instr->len);
> +
> + div_u64_rem(instr->len, mtd->erasesize, &rem);
> + if (rem)
> + return -EINVAL;
> +
> + addr = instr->addr;
> + len = instr->len;
> +
> + while (len) {
> + write_enable(nor);
> +
> + ret = spi_nor_erase_sector(nor, addr);
> + if (ret)
> + goto erase_err;
> +
> + addr += mtd->erasesize;
> + len -= mtd->erasesize;
> +
> + ret = spi_nor_wait_till_ready(nor);
> + if (ret)
> + goto erase_err;
> + }
> +
> + write_disable(nor);
> +
> +erase_err:
> + return ret;
> +}
> +
> +#if defined(CONFIG_SPI_FLASH_STMICRO) || defined(CONFIG_SPI_FLASH_SST)
> +/* Write status register and ensure bits in mask match written values */
> +static int write_sr_and_check(struct spi_nor *nor, u8 status_new, u8 mask)
> +{
> + int ret;
> +
> + write_enable(nor);
> + ret = write_sr(nor, status_new);
> + if (ret)
> + return ret;
> +
> + ret = spi_nor_wait_till_ready(nor);
> + if (ret)
> + return ret;
> +
> + ret = read_sr(nor);
> + if (ret < 0)
> + return ret;
> +
> + return ((ret & mask) != (status_new & mask)) ? -EIO : 0;
> +}
> +
> +static void stm_get_locked_range(struct spi_nor *nor, u8 sr, loff_t *ofs,
> + uint64_t *len)
> +{
> + struct mtd_info *mtd = &nor->mtd;
> + u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
> + int shift = ffs(mask) - 1;
> + int pow;
> +
> + if (!(sr & mask)) {
> + /* No protection */
> + *ofs = 0;
> + *len = 0;
> + } else {
> + pow = ((sr & mask) ^ mask) >> shift;
> + *len = mtd->size >> pow;
> + if (nor->flags & SNOR_F_HAS_SR_TB && sr & SR_TB)
> + *ofs = 0;
> + else
> + *ofs = mtd->size - *len;
> + }
> +}
> +
> +/*
> + * Return 1 if the entire region is locked (if @locked is true) or unlocked (if
> + * @locked is false); 0 otherwise
> + */
> +static int stm_check_lock_status_sr(struct spi_nor *nor, loff_t ofs, u64 len,
> + u8 sr, bool locked)
> +{
> + loff_t lock_offs;
> + uint64_t lock_len;
> +
> + if (!len)
> + return 1;
> +
> + stm_get_locked_range(nor, sr, &lock_offs, &lock_len);
> +
> + if (locked)
> + /* Requested range is a sub-range of locked range */
> + return (ofs + len <= lock_offs + lock_len) && (ofs >= lock_offs);
> + else
> + /* Requested range does not overlap with locked range */
> + return (ofs >= lock_offs + lock_len) || (ofs + len <= lock_offs);
> +}
> +
> +static int stm_is_locked_sr(struct spi_nor *nor, loff_t ofs, uint64_t len,
> + u8 sr)
> +{
> + return stm_check_lock_status_sr(nor, ofs, len, sr, true);
> +}
> +
> +static int stm_is_unlocked_sr(struct spi_nor *nor, loff_t ofs, uint64_t len,
> + u8 sr)
> +{
> + return stm_check_lock_status_sr(nor, ofs, len, sr, false);
> +}
> +
> +/*
> + * Lock a region of the flash. Compatible with ST Micro and similar flash.
> + * Supports the block protection bits BP{0,1,2} in the status register
> + * (SR). Does not support these features found in newer SR bitfields:
> + * - SEC: sector/block protect - only handle SEC=0 (block protect)
> + * - CMP: complement protect - only support CMP=0 (range is not complemented)
> + *
> + * Support for the following is provided conditionally for some flash:
> + * - TB: top/bottom protect
> + *
> + * Sample table portion for 8MB flash (Winbond w25q64fw):
> + *
> + * SEC | TB | BP2 | BP1 | BP0 | Prot Length | Protected Portion
> + * --------------------------------------------------------------------------
> + * X | X | 0 | 0 | 0 | NONE | NONE
> + * 0 | 0 | 0 | 0 | 1 | 128 KB | Upper 1/64
> + * 0 | 0 | 0 | 1 | 0 | 256 KB | Upper 1/32
> + * 0 | 0 | 0 | 1 | 1 | 512 KB | Upper 1/16
> + * 0 | 0 | 1 | 0 | 0 | 1 MB | Upper 1/8
> + * 0 | 0 | 1 | 0 | 1 | 2 MB | Upper 1/4
> + * 0 | 0 | 1 | 1 | 0 | 4 MB | Upper 1/2
> + * X | X | 1 | 1 | 1 | 8 MB | ALL
> + * ------|-------|-------|-------|-------|---------------|-------------------
> + * 0 | 1 | 0 | 0 | 1 | 128 KB | Lower 1/64
> + * 0 | 1 | 0 | 1 | 0 | 256 KB | Lower 1/32
> + * 0 | 1 | 0 | 1 | 1 | 512 KB | Lower 1/16
> + * 0 | 1 | 1 | 0 | 0 | 1 MB | Lower 1/8
> + * 0 | 1 | 1 | 0 | 1 | 2 MB | Lower 1/4
> + * 0 | 1 | 1 | 1 | 0 | 4 MB | Lower 1/2
> + *
> + * Returns negative on errors, 0 on success.
> + */
> +static int stm_lock(struct spi_nor *nor, loff_t ofs, uint64_t len)
> +{
> + struct mtd_info *mtd = &nor->mtd;
> + int status_old, status_new;
> + u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
> + u8 shift = ffs(mask) - 1, pow, val;
> + loff_t lock_len;
> + bool can_be_top = true, can_be_bottom = nor->flags & SNOR_F_HAS_SR_TB;
> + bool use_top;
> +
> + status_old = read_sr(nor);
> + if (status_old < 0)
> + return status_old;
> +
> + /* If nothing in our range is unlocked, we don't need to do anything */
> + if (stm_is_locked_sr(nor, ofs, len, status_old))
> + return 0;
> +
> + /* If anything below us is unlocked, we can't use 'bottom' protection */
> + if (!stm_is_locked_sr(nor, 0, ofs, status_old))
> + can_be_bottom = false;
> +
> + /* If anything above us is unlocked, we can't use 'top' protection */
> + if (!stm_is_locked_sr(nor, ofs + len, mtd->size - (ofs + len),
> + status_old))
> + can_be_top = false;
> +
> + if (!can_be_bottom && !can_be_top)
> + return -EINVAL;
> +
> + /* Prefer top, if both are valid */
> + use_top = can_be_top;
> +
> + /* lock_len: length of region that should end up locked */
> + if (use_top)
> + lock_len = mtd->size - ofs;
> + else
> + lock_len = ofs + len;
> +
> + /*
> + * Need smallest pow such that:
> + *
> + * 1 / (2^pow) <= (len / size)
> + *
> + * so (assuming power-of-2 size) we do:
> + *
> + * pow = ceil(log2(size / len)) = log2(size) - floor(log2(len))
> + */
> + pow = ilog2(mtd->size) - ilog2(lock_len);
> + val = mask - (pow << shift);
> + if (val & ~mask)
> + return -EINVAL;
> + /* Don't "lock" with no region! */
> + if (!(val & mask))
> + return -EINVAL;
> +
> + status_new = (status_old & ~mask & ~SR_TB) | val;
> +
> + /* Disallow further writes if WP pin is asserted */
> + status_new |= SR_SRWD;
> +
> + if (!use_top)
> + status_new |= SR_TB;
> +
> + /* Don't bother if they're the same */
> + if (status_new == status_old)
> + return 0;
> +
> + /* Only modify protection if it will not unlock other areas */
> + if ((status_new & mask) < (status_old & mask))
> + return -EINVAL;
> +
> + return write_sr_and_check(nor, status_new, mask);
> +}
> +
> +/*
> + * Unlock a region of the flash. See stm_lock() for more info
> + *
> + * Returns negative on errors, 0 on success.
> + */
> +static int stm_unlock(struct spi_nor *nor, loff_t ofs, uint64_t len)
> +{
> + struct mtd_info *mtd = &nor->mtd;
> + int status_old, status_new;
> + u8 mask = SR_BP2 | SR_BP1 | SR_BP0;
> + u8 shift = ffs(mask) - 1, pow, val;
> + loff_t lock_len;
> + bool can_be_top = true, can_be_bottom = nor->flags & SNOR_F_HAS_SR_TB;
> + bool use_top;
> +
> + status_old = read_sr(nor);
> + if (status_old < 0)
> + return status_old;
> +
> + /* If nothing in our range is locked, we don't need to do anything */
> + if (stm_is_unlocked_sr(nor, ofs, len, status_old))
> + return 0;
> +
> + /* If anything below us is locked, we can't use 'top' protection */
> + if (!stm_is_unlocked_sr(nor, 0, ofs, status_old))
> + can_be_top = false;
> +
> + /* If anything above us is locked, we can't use 'bottom' protection */
> + if (!stm_is_unlocked_sr(nor, ofs + len, mtd->size - (ofs + len),
> + status_old))
> + can_be_bottom = false;
> +
> + if (!can_be_bottom && !can_be_top)
> + return -EINVAL;
> +
> + /* Prefer top, if both are valid */
> + use_top = can_be_top;
> +
> + /* lock_len: length of region that should remain locked */
> + if (use_top)
> + lock_len = mtd->size - (ofs + len);
> + else
> + lock_len = ofs;
> +
> + /*
> + * Need largest pow such that:
> + *
> + * 1 / (2^pow) >= (len / size)
> + *
> + * so (assuming power-of-2 size) we do:
> + *
> + * pow = floor(log2(size / len)) = log2(size) - ceil(log2(len))
> + */
> + pow = ilog2(mtd->size) - order_base_2(lock_len);
> + if (lock_len == 0) {
> + val = 0; /* fully unlocked */
> + } else {
> + val = mask - (pow << shift);
> + /* Some power-of-two sizes are not supported */
> + if (val & ~mask)
> + return -EINVAL;
> + }
> +
> + status_new = (status_old & ~mask & ~SR_TB) | val;
> +
> + /* Don't protect status register if we're fully unlocked */
> + if (lock_len == 0)
> + status_new &= ~SR_SRWD;
> +
> + if (!use_top)
> + status_new |= SR_TB;
> +
> + /* Don't bother if they're the same */
> + if (status_new == status_old)
> + return 0;
> +
> + /* Only modify protection if it will not lock other areas */
> + if ((status_new & mask) > (status_old & mask))
> + return -EINVAL;
> +
> + return write_sr_and_check(nor, status_new, mask);
> +}
> +
> +/*
> + * Check if a region of the flash is (completely) locked. See stm_lock() for
> + * more info.
> + *
> + * Returns 1 if entire region is locked, 0 if any portion is unlocked, and
> + * negative on errors.
> + */
> +static int stm_is_locked(struct spi_nor *nor, loff_t ofs, uint64_t len)
> +{
> + int status;
> +
> + status = read_sr(nor);
> + if (status < 0)
> + return status;
> +
> + return stm_is_locked_sr(nor, ofs, len, status);
> +}
> +#endif /* CONFIG_SPI_FLASH_STMICRO */
> +
> +/* Used when the "_ext_id" is two bytes at most */
> +#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
> + .id = { \
> + ((_jedec_id) >> 16) & 0xff, \
> + ((_jedec_id) >> 8) & 0xff, \
> + (_jedec_id) & 0xff, \
> + ((_ext_id) >> 8) & 0xff, \
> + (_ext_id) & 0xff, \
> + }, \
> + .id_len = (!(_jedec_id) ? 0 : (3 + ((_ext_id) ? 2 : 0))), \
> + .sector_size = (_sector_size), \
> + .n_sectors = (_n_sectors), \
> + .page_size = 256, \
> + .flags = (_flags),
> +
> +#define INFO6(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
> + .id = { \
> + ((_jedec_id) >> 16) & 0xff, \
> + ((_jedec_id) >> 8) & 0xff, \
> + (_jedec_id) & 0xff, \
> + ((_ext_id) >> 16) & 0xff, \
> + ((_ext_id) >> 8) & 0xff, \
> + (_ext_id) & 0xff, \
> + }, \
> + .id_len = 6, \
> + .sector_size = (_sector_size), \
> + .n_sectors = (_n_sectors), \
> + .page_size = 256, \
> + .flags = (_flags),
> +
> +/* NOTE: double check command sets and memory organization when you add
> + * more nor chips. This current list focusses on newer chips, which
> + * have been converging on command sets which including JEDEC ID.
> + *
> + * All newly added entries should describe *hardware* and should use SECT_4K
> + * (or SECT_4K_PMC) if hardware supports erasing 4 KiB sectors. For usage
> + * scenarios excluding small sectors there is config option that can be
> + * disabled: CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.
> + * For historical (and compatibility) reasons (before we got above config) some
> + * old entries may be missing 4K flag.
> + */
> +const struct flash_info spi_nor_ids[] = {
> +#ifdef CONFIG_SPI_FLASH_ATMEL /* ATMEL */
> + /* Atmel -- some are (confusingly) marketed as "DataFlash" */
> + { "at26df321", INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) },
> + { "at25df321a", INFO(0x1f4701, 0, 64 * 1024, 64, SECT_4K) },
> +
> + { "at45db011d", INFO(0x1f2200, 0, 64 * 1024, 4, SECT_4K) },
> + { "at45db021d", INFO(0x1f2300, 0, 64 * 1024, 8, SECT_4K) },
> + { "at45db041d", INFO(0x1f2400, 0, 64 * 1024, 8, SECT_4K) },
> + { "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) },
> + { "at45db161d", INFO(0x1f2600, 0, 64 * 1024, 32, SECT_4K) },
> + { "at45db321d", INFO(0x1f2700, 0, 64 * 1024, 64, SECT_4K) },
> + { "at45db641d", INFO(0x1f2800, 0, 64 * 1024, 128, SECT_4K) },
> + { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) },
> +#endif
> +#ifdef CONFIG_SPI_FLASH_EON /* EON */
> + /* EON -- en25xxx */
> + { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) },
> + { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) },
> + { "en25qh128", INFO(0x1c7018, 0, 64 * 1024, 256, 0) },
> + { "en25s64", INFO(0x1c3817, 0, 64 * 1024, 128, SECT_4K) },
> +#endif
> +#ifdef CONFIG_SPI_FLASH_GIGADEVICE /* GIGADEVICE */
> + /* GigaDevice */
> + {
> + "gd25q16", INFO(0xc84015, 0, 64 * 1024, 32,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
> + SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
> + },
> + {
> + "gd25q32", INFO(0xc84016, 0, 64 * 1024, 64,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
> + SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
> + },
> + {
> + "gd25lq32", INFO(0xc86016, 0, 64 * 1024, 64,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
> + SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
> + },
> + {
> + "gd25q64", INFO(0xc84017, 0, 64 * 1024, 128,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
> + SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
> + },
> +#endif
> +#ifdef CONFIG_SPI_FLASH_ISSI /* ISSI */
> + /* ISSI */
> + { "is25lq040b", INFO(0x9d4013, 0, 64 * 1024, 8,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "is25lp032", INFO(0x9d6016, 0, 64 * 1024, 64, 0) },
> + { "is25lp064", INFO(0x9d6017, 0, 64 * 1024, 128, 0) },
> + { "is25lp128", INFO(0x9d6018, 0, 64 * 1024, 256,
> + SECT_4K | SPI_NOR_DUAL_READ) },
> + { "is25lp256", INFO(0x9d6019, 0, 64 * 1024, 512,
> + SECT_4K | SPI_NOR_DUAL_READ) },
> + { "is25wp032", INFO(0x9d7016, 0, 64 * 1024, 64,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "is25wp064", INFO(0x9d7017, 0, 64 * 1024, 128,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "is25wp128", INFO(0x9d7018, 0, 64 * 1024, 256,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> +#endif
> +#ifdef CONFIG_SPI_FLASH_MACRONIX /* MACRONIX */
> + /* Macronix */
> + { "mx25l2005a", INFO(0xc22012, 0, 64 * 1024, 4, SECT_4K) },
> + { "mx25l4005a", INFO(0xc22013, 0, 64 * 1024, 8, SECT_4K) },
> + { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) },
> + { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) },
> + { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, SECT_4K) },
> + { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, SECT_4K) },
> + { "mx25u2033e", INFO(0xc22532, 0, 64 * 1024, 4, SECT_4K) },
> + { "mx25u1635e", INFO(0xc22535, 0, 64 * 1024, 32, SECT_4K) },
> + { "mx25u6435f", INFO(0xc22537, 0, 64 * 1024, 128, SECT_4K) },
> + { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
> + { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
> + { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "mx25u25635f", INFO(0xc22539, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_4B_OPCODES) },
> + { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
> + { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
> + { "mx66u51235f", INFO(0xc2253a, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
> + { "mx66l1g45g", INFO(0xc2201b, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "mx25l1633e", INFO(0xc22415, 0, 64 * 1024, 32, SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES | SECT_4K) },
> +#endif
> +
> +#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
> + /* Micron */
> + { "n25q016a", INFO(0x20bb15, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_QUAD_READ) },
> + { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
> + { "n25q032a", INFO(0x20bb16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
> + { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
> + { "n25q064a", INFO(0x20bb17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
> + { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
> + { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
> + { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "n25q256ax1", INFO(0x20bb19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_QUAD_READ) },
> + { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
> + { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
> + { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
> + { "n25q00a", INFO(0x20bb21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
> + { "mt25qu02g", INFO(0x20bb22, 0, 64 * 1024, 4096, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
> +#endif
> +#ifdef CONFIG_SPI_FLASH_SPANSION /* SPANSION */
> + /* Spansion/Cypress -- single (large) sector size only, at least
> + * for the chips listed here (without boot sectors).
> + */
> + { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR) },
> + { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> + { "s25fl512s", INFO6(0x010220, 0x4d0081, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> + { "s25fl512s_256k", INFO(0x010220, 0x4d00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> + { "s25fl512s_64k", INFO(0x010220, 0x4d01, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> + { "s25fl512s_512k", INFO(0x010220, 0x4f00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> + { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
> + { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
> + { "s25fl128s", INFO6(0x012018, 0x4d0180, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> + { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> + { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> + { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
> + { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
> + { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) },
> + { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) },
> + { "s25fl116k", INFO(0x014015, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "s25fl164k", INFO(0x014017, 0, 64 * 1024, 128, SECT_4K) },
> + { "s25fl208k", INFO(0x014014, 0, 64 * 1024, 16, SECT_4K | SPI_NOR_DUAL_READ) },
> + { "s25fl128l", INFO(0x016018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
> +#endif
> +#ifdef CONFIG_SPI_FLASH_SST /* SST */
> + /* SST -- large erase sizes are "overlays", "sectors" are 4K */
> + { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
> + { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
> + { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K | SST_WRITE) },
> + { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K | SST_WRITE) },
> + { "sst25vf064c", INFO(0xbf254b, 0, 64 * 1024, 128, SECT_4K) },
> + { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1, SECT_4K | SST_WRITE) },
> + { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2, SECT_4K | SST_WRITE) },
> + { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4, SECT_4K | SST_WRITE) },
> + { "sst25wf020a", INFO(0x621612, 0, 64 * 1024, 4, SECT_4K) },
> + { "sst25wf040b", INFO(0x621613, 0, 64 * 1024, 8, SECT_4K) },
> + { "sst25wf040", INFO(0xbf2504, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
> + { "sst25wf080", INFO(0xbf2505, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
> + { "sst26vf064b", INFO(0xbf2643, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "sst26wf016", INFO(0xbf2651, 0, 64 * 1024, 32, SECT_4K) },
> + { "sst26wf032", INFO(0xbf2622, 0, 64 * 1024, 64, SECT_4K) },
> + { "sst26wf064", INFO(0xbf2643, 0, 64 * 1024, 128, SECT_4K) },
> +#endif
> +#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
> + /* ST Microelectronics -- newer production may have feature updates */
> + { "m25p10", INFO(0x202011, 0, 32 * 1024, 4, 0) },
> + { "m25p20", INFO(0x202012, 0, 64 * 1024, 4, 0) },
> + { "m25p40", INFO(0x202013, 0, 64 * 1024, 8, 0) },
> + { "m25p80", INFO(0x202014, 0, 64 * 1024, 16, 0) },
> + { "m25p16", INFO(0x202015, 0, 64 * 1024, 32, 0) },
> + { "m25p32", INFO(0x202016, 0, 64 * 1024, 64, 0) },
> + { "m25p64", INFO(0x202017, 0, 64 * 1024, 128, 0) },
> + { "m25p128", INFO(0x202018, 0, 256 * 1024, 64, 0) },
> + { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) },
> + { "m25px16", INFO(0x207115, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "m25px64", INFO(0x207117, 0, 64 * 1024, 128, 0) },
> +#endif
> +#ifdef CONFIG_SPI_FLASH_WINBOND /* WINBOND */
> + /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
> + { "w25x05", INFO(0xef3010, 0, 64 * 1024, 1, SECT_4K) },
> + { "w25x10", INFO(0xef3011, 0, 64 * 1024, 2, SECT_4K) },
> + { "w25x20", INFO(0xef3012, 0, 64 * 1024, 4, SECT_4K) },
> + { "w25x40", INFO(0xef3013, 0, 64 * 1024, 8, SECT_4K) },
> + { "w25x80", INFO(0xef3014, 0, 64 * 1024, 16, SECT_4K) },
> + { "w25x16", INFO(0xef3015, 0, 64 * 1024, 32, SECT_4K) },
> + {
> + "w25q16dw", INFO(0xef6015, 0, 64 * 1024, 32,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
> + SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
> + },
> + { "w25x32", INFO(0xef3016, 0, 64 * 1024, 64, SECT_4K) },
> + { "w25q20cl", INFO(0xef4012, 0, 64 * 1024, 4, SECT_4K) },
> + { "w25q20bw", INFO(0xef5012, 0, 64 * 1024, 4, SECT_4K) },
> + { "w25q20ew", INFO(0xef6012, 0, 64 * 1024, 4, SECT_4K) },
> + { "w25q32", INFO(0xef4016, 0, 64 * 1024, 64, SECT_4K) },
> + {
> + "w25q32dw", INFO(0xef6016, 0, 64 * 1024, 64,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
> + SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
> + },
> + {
> + "w25q32jv", INFO(0xef7016, 0, 64 * 1024, 64,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
> + SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
> + },
> + { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
> + { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
> + {
> + "w25q64dw", INFO(0xef6017, 0, 64 * 1024, 128,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
> + SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
> + },
> + {
> + "w25q128fw", INFO(0xef6018, 0, 64 * 1024, 256,
> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
> + SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
> + },
> + { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) },
> + { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) },
> + { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) },
> + { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024,
> + SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ) },
> +#endif
> +#ifdef CONFIG_SPI_FLASH_XMC
> + /* XMC (Wuhan Xinxin Semiconductor Manufacturing Corp.) */
> + { "XM25QH64A", INFO(0x207017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> + { "XM25QH128A", INFO(0x207018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
> +#endif
> + { },
> +};
> +
> +static const struct flash_info *spi_nor_read_id(struct spi_nor *nor)
> +{
> + int tmp;
> + u8 id[SPI_NOR_MAX_ID_LEN];
> + const struct flash_info *info;
> +
> + if (!ARRAY_SIZE(spi_nor_ids))
> + return ERR_PTR(-ENODEV);
> +
> + tmp = nor->read_reg(nor, SPINOR_OP_RDID, id, SPI_NOR_MAX_ID_LEN);
> + if (tmp < 0) {
> + dev_dbg(nor->dev, "error %d reading JEDEC ID\n", tmp);
> + return ERR_PTR(tmp);
> + }
> +
> + for (tmp = 0; tmp < ARRAY_SIZE(spi_nor_ids) - 1; tmp++) {
> + info = &spi_nor_ids[tmp];
> + if (info->id_len) {
> + if (!memcmp(info->id, id, info->id_len))
> + return &spi_nor_ids[tmp];
> + }
> + }
> + dev_err(nor->dev, "unrecognized JEDEC id bytes: %02x, %02x, %02x\n",
> + id[0], id[1], id[2]);
> + return ERR_PTR(-ENODEV);
> +}
> +
> +static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
> + size_t *retlen, u_char *buf)
> +{
> + struct spi_nor *nor = mtd_to_spi_nor(mtd);
> + int ret;
> +
> + dev_dbg(nor->dev, "from 0x%08x, len %zd\n", (u32)from, len);
> +
> + while (len) {
> + loff_t addr = from;
> +
> + ret = nor->read(nor, addr, len, buf);
> + if (ret == 0) {
> + /* We shouldn't see 0-length reads */
> + ret = -EIO;
> + goto read_err;
> + }
> + if (ret < 0)
> + goto read_err;
> +
> + *retlen += ret;
> + buf += ret;
> + from += ret;
> + len -= ret;
> + }
> + ret = 0;
> +
> +read_err:
> + return ret;
> +}
> +
> +#ifdef CONFIG_SPI_FLASH_SST
> +static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
> + size_t *retlen, const u_char *buf)
> +{
> + struct spi_nor *nor = mtd_to_spi_nor(mtd);
> + size_t actual;
> + int ret;
> +
> + dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
> +
> + write_enable(nor);
> +
> + nor->sst_write_second = false;
> +
> + actual = to % 2;
> + /* Start write from odd address. */
> + if (actual) {
> + nor->program_opcode = SPINOR_OP_BP;
> +
> + /* write one byte. */
> + ret = nor->write(nor, to, 1, buf);
> + if (ret < 0)
> + goto sst_write_err;
> + ret = spi_nor_wait_till_ready(nor);
> + if (ret)
> + goto sst_write_err;
> + }
> + to += actual;
> +
> + /* Write out most of the data here. */
> + for (; actual < len - 1; actual += 2) {
> + nor->program_opcode = SPINOR_OP_AAI_WP;
> +
> + /* write two bytes. */
> + ret = nor->write(nor, to, 2, buf + actual);
> + if (ret < 0)
> + goto sst_write_err;
> + ret = spi_nor_wait_till_ready(nor);
> + if (ret)
> + goto sst_write_err;
> + to += 2;
> + nor->sst_write_second = true;
> + }
> + nor->sst_write_second = false;
> +
> + write_disable(nor);
> + ret = spi_nor_wait_till_ready(nor);
> + if (ret)
> + goto sst_write_err;
> +
> + /* Write out trailing byte if it exists. */
> + if (actual != len) {
> + write_enable(nor);
> +
> + nor->program_opcode = SPINOR_OP_BP;
> + ret = nor->write(nor, to, 1, buf + actual);
> + if (ret < 0)
> + goto sst_write_err;
> + ret = spi_nor_wait_till_ready(nor);
> + if (ret)
> + goto sst_write_err;
> + write_disable(nor);
> + actual += 1;
> + }
> +sst_write_err:
> + *retlen += actual;
> + return ret;
> +}
> +#endif
> +/*
> + * Write an address range to the nor chip. Data must be written in
> + * FLASH_PAGESIZE chunks. The address range may be any size provided
> + * it is within the physical boundaries.
> + */
> +static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
> + size_t *retlen, const u_char *buf)
> +{
> + struct spi_nor *nor = mtd_to_spi_nor(mtd);
> + size_t page_offset, page_remain, i;
> + ssize_t ret;
> +
> + dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
> +
> + for (i = 0; i < len; ) {
> + ssize_t written;
> + loff_t addr = to + i;
> +
> + /*
> + * If page_size is a power of two, the offset can be quickly
> + * calculated with an AND operation. On the other cases we
> + * need to do a modulus operation (more expensive).
> + * Power of two numbers have only one bit set and we can use
> + * the instruction hweight32 to detect if we need to do a
> + * modulus (do_div()) or not.
> + */
> + if (hweight32(nor->page_size) == 1) {
> + page_offset = addr & (nor->page_size - 1);
> + } else {
> + u64 aux = addr;
> +
> + page_offset = do_div(aux, nor->page_size);
> + }
> + /* the size of data remaining on the first page */
> + page_remain = min_t(size_t,
> + nor->page_size - page_offset, len - i);
> +
> + write_enable(nor);
> + ret = nor->write(nor, addr, page_remain, buf + i);
> + if (ret < 0)
> + goto write_err;
> + written = ret;
> +
> + ret = spi_nor_wait_till_ready(nor);
> + if (ret)
> + goto write_err;
> + *retlen += written;
> + i += written;
> + if (written != page_remain) {
> + ret = -EIO;
> + goto write_err;
> + }
> + }
> +
> +write_err:
> + return ret;
> +}
> +
> +#ifdef CONFIG_SPI_FLASH_MACRONIX
> +/**
> + * macronix_quad_enable() - set QE bit in Status Register.
> + * @nor: pointer to a 'struct spi_nor'
> + *
> + * Set the Quad Enable (QE) bit in the Status Register.
> + *
> + * bit 6 of the Status Register is the QE bit for Macronix like QSPI memories.
> + *
> + * Return: 0 on success, -errno otherwise.
> + */
> +static int macronix_quad_enable(struct spi_nor *nor)
> +{
> + int ret, val;
> +
> + val = read_sr(nor);
> + if (val < 0)
> + return val;
> + if (val & SR_QUAD_EN_MX)
> + return 0;
> +
> + write_enable(nor);
> +
> + write_sr(nor, val | SR_QUAD_EN_MX);
> +
> + ret = spi_nor_wait_till_ready(nor);
> + if (ret)
> + return ret;
> +
> + ret = read_sr(nor);
> + if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) {
> + dev_err(nor->dev, "Macronix Quad bit not set\n");
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +#endif
> +
> +#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
> +/*
> + * Write status Register and configuration register with 2 bytes
> + * The first byte will be written to the status register, while the
> + * second byte will be written to the configuration register.
> + * Return negative if error occurred.
> + */
> +static int write_sr_cr(struct spi_nor *nor, u8 *sr_cr)
> +{
> + int ret;
> +
> + write_enable(nor);
> +
> + ret = nor->write_reg(nor, SPINOR_OP_WRSR, sr_cr, 2);
> + if (ret < 0) {
> + dev_dbg(nor->dev,
> + "error while writing configuration register\n");
> + return -EINVAL;
> + }
> +
> + ret = spi_nor_wait_till_ready(nor);
> + if (ret) {
> + dev_dbg(nor->dev,
> + "timeout while writing configuration register\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * spansion_read_cr_quad_enable() - set QE bit in Configuration Register.
> + * @nor: pointer to a 'struct spi_nor'
> + *
> + * Set the Quad Enable (QE) bit in the Configuration Register.
> + * This function should be used with QSPI memories supporting the Read
> + * Configuration Register (35h) instruction.
> + *
> + * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
> + * memories.
> + *
> + * Return: 0 on success, -errno otherwise.
> + */
> +static int spansion_read_cr_quad_enable(struct spi_nor *nor)
> +{
> + u8 sr_cr[2];
> + int ret;
> +
> + /* Check current Quad Enable bit value. */
> + ret = read_cr(nor);
> + if (ret < 0) {
> + dev_dbg(dev, "error while reading configuration register\n");
> + return -EINVAL;
> + }
> +
> + if (ret & CR_QUAD_EN_SPAN)
> + return 0;
> +
> + sr_cr[1] = ret | CR_QUAD_EN_SPAN;
> +
> + /* Keep the current value of the Status Register. */
> + ret = read_sr(nor);
> + if (ret < 0) {
> + dev_dbg(dev, "error while reading status register\n");
> + return -EINVAL;
> + }
> + sr_cr[0] = ret;
> +
> + ret = write_sr_cr(nor, sr_cr);
> + if (ret)
> + return ret;
> +
> + /* Read back and check it. */
> + ret = read_cr(nor);
> + if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) {
> + dev_dbg(nor->dev, "Spansion Quad bit not set\n");
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +#if CONFIG_IS_ENABLED(SPI_FLASH_SFDP_SUPPORT)
> +/**
> + * spansion_no_read_cr_quad_enable() - set QE bit in Configuration Register.
> + * @nor: pointer to a 'struct spi_nor'
> + *
> + * Set the Quad Enable (QE) bit in the Configuration Register.
> + * This function should be used with QSPI memories not supporting the Read
> + * Configuration Register (35h) instruction.
> + *
> + * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
> + * memories.
> + *
> + * Return: 0 on success, -errno otherwise.
> + */
> +static int spansion_no_read_cr_quad_enable(struct spi_nor *nor)
> +{
> + u8 sr_cr[2];
> + int ret;
> +
> + /* Keep the current value of the Status Register. */
> + ret = read_sr(nor);
> + if (ret < 0) {
> + dev_dbg(nor->dev, "error while reading status register\n");
> + return -EINVAL;
> + }
> + sr_cr[0] = ret;
> + sr_cr[1] = CR_QUAD_EN_SPAN;
> +
> + return write_sr_cr(nor, sr_cr);
> +}
> +
> +#endif /* CONFIG_SPI_FLASH_SFDP_SUPPORT */
> +#endif /* CONFIG_SPI_FLASH_SPANSION */
> +
> +struct spi_nor_read_command {
> + u8 num_mode_clocks;
> + u8 num_wait_states;
> + u8 opcode;
> + enum spi_nor_protocol proto;
> +};
> +
> +struct spi_nor_pp_command {
> + u8 opcode;
> + enum spi_nor_protocol proto;
> +};
> +
> +enum spi_nor_read_command_index {
> + SNOR_CMD_READ,
> + SNOR_CMD_READ_FAST,
> + SNOR_CMD_READ_1_1_1_DTR,
> +
> + /* Dual SPI */
> + SNOR_CMD_READ_1_1_2,
> + SNOR_CMD_READ_1_2_2,
> + SNOR_CMD_READ_2_2_2,
> + SNOR_CMD_READ_1_2_2_DTR,
> +
> + /* Quad SPI */
> + SNOR_CMD_READ_1_1_4,
> + SNOR_CMD_READ_1_4_4,
> + SNOR_CMD_READ_4_4_4,
> + SNOR_CMD_READ_1_4_4_DTR,
> +
> + /* Octo SPI */
> + SNOR_CMD_READ_1_1_8,
> + SNOR_CMD_READ_1_8_8,
> + SNOR_CMD_READ_8_8_8,
> + SNOR_CMD_READ_1_8_8_DTR,
> +
> + SNOR_CMD_READ_MAX
> +};
> +
> +enum spi_nor_pp_command_index {
> + SNOR_CMD_PP,
> +
> + /* Quad SPI */
> + SNOR_CMD_PP_1_1_4,
> + SNOR_CMD_PP_1_4_4,
> + SNOR_CMD_PP_4_4_4,
> +
> + /* Octo SPI */
> + SNOR_CMD_PP_1_1_8,
> + SNOR_CMD_PP_1_8_8,
> + SNOR_CMD_PP_8_8_8,
> +
> + SNOR_CMD_PP_MAX
> +};
I'm afraid whether we teatsed all thse combinations? or we doing for
the sake of Linux sync?
> --
> 2.20.1
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot
--
Jagan Teki
Senior Linux Kernel Engineer | Amarula Solutions
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 09/11] configs: Remove SF_DUAL_FLASH
2019-01-25 15:01 ` Vignesh R
@ 2019-01-28 6:36 ` Jagan Teki
0 siblings, 0 replies; 33+ messages in thread
From: Jagan Teki @ 2019-01-28 6:36 UTC (permalink / raw)
To: u-boot
On Fri, Jan 25, 2019 at 8:30 PM Vignesh R <vigneshr@ti.com> wrote:
>
>
>
> On 25/01/19 8:17 PM, Jagan Teki wrote:
> > On Fri, Dec 21, 2018 at 12:18 PM Vignesh R <vigneshr@ti.com> wrote:
> >>
> >> SF_DUAL_FLASH claims to enable support for SF_DUAL_STACKED_FLASH and
> >> SF_DUAL_PARALLEL_FLASH. But, in current U-Boot code, grepping for above
> >> enums yield no user and therefore support seems to be incomplete. Remove
> >> these configs so as to avoid confusion.
> >
> > So, with Linux sync. all dual flash code is dropped is it?
> >
>
> Yes, because Linux does not support dual flash. I did try to add back
> dual flash support, but could not find any SPI flash claiming
> SF_DUAL_FLASH capability in today's U-Boot code. Therefore, this patch
> just drops the CONFIG option.
> Dual flash can always be added back to this framework when there is an
> actual user of the code in _mainline_ U-Boot.
As I said in previous version patches, it is not always to have some
functionalities in Linux and dual flash is useful for bootloader in
Xilinx Zynq IP's. True that nothing has been done in Linux front and
even we asked about the "plan of work" on this context to Michal and
Siva in previous mails, unfortunately no is responded. On that note
I'm fine with going this change, thanks.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 01/11] spi-mem: Claim SPI bus before spi mem access
2018-12-21 6:38 ` [U-Boot] [PATCH v2 01/11] spi-mem: Claim SPI bus before spi mem access Vignesh R
@ 2019-01-28 6:54 ` Jagan Teki
2019-01-28 9:44 ` Vignesh R
0 siblings, 1 reply; 33+ messages in thread
From: Jagan Teki @ 2019-01-28 6:54 UTC (permalink / raw)
To: u-boot
On Fri, Dec 21, 2018 at 12:08 PM Vignesh R <vigneshr@ti.com> wrote:
>
> It is necessary to call spi_claim_bus() before starting any SPI
> transactions and this restriction would also apply when calling spi-mem
> operationss. Therefore claim and release bus before requesting transfer
> via exec_op.
>
> Signed-off-by: Vignesh R <vigneshr@ti.com>
> ---
> drivers/spi/spi-mem.c | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
> index 1da20b8de5c4..4c1463118ab2 100644
> --- a/drivers/spi/spi-mem.c
> +++ b/drivers/spi/spi-mem.c
> @@ -231,7 +231,13 @@ int spi_mem_exec_op(struct spi_slave *slave, const struct spi_mem_op *op)
> mutex_lock(&ctlr->bus_lock_mutex);
> mutex_lock(&ctlr->io_mutex);
> #endif
> + ret = spi_claim_bus(slave);
> + if (ret < 0)
> + return ret;
> +
> ret = ops->mem_ops->exec_op(slave, op);
> +
> + spi_release_bus(slave);
This making spi claims twice, since it's been doing before spi_xfer in
below code. better to make it before the if.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 01/11] spi-mem: Claim SPI bus before spi mem access
2019-01-28 6:54 ` Jagan Teki
@ 2019-01-28 9:44 ` Vignesh R
0 siblings, 0 replies; 33+ messages in thread
From: Vignesh R @ 2019-01-28 9:44 UTC (permalink / raw)
To: u-boot
On 28/01/19 12:24 PM, Jagan Teki wrote:
> On Fri, Dec 21, 2018 at 12:08 PM Vignesh R <vigneshr@ti.com> wrote:
>>
>> It is necessary to call spi_claim_bus() before starting any SPI
>> transactions and this restriction would also apply when calling spi-mem
>> operationss. Therefore claim and release bus before requesting transfer
>> via exec_op.
>>
>> Signed-off-by: Vignesh R <vigneshr@ti.com>
>> ---
>> drivers/spi/spi-mem.c | 6 ++++++
>> 1 file changed, 6 insertions(+)
>>
>> diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
>> index 1da20b8de5c4..4c1463118ab2 100644
>> --- a/drivers/spi/spi-mem.c
>> +++ b/drivers/spi/spi-mem.c
>> @@ -231,7 +231,13 @@ int spi_mem_exec_op(struct spi_slave *slave, const struct spi_mem_op *op)
>> mutex_lock(&ctlr->bus_lock_mutex);
>> mutex_lock(&ctlr->io_mutex);
>> #endif
>> + ret = spi_claim_bus(slave);
>> + if (ret < 0)
>> + return ret;
>> +
>> ret = ops->mem_ops->exec_op(slave, op);
>> +
>> + spi_release_bus(slave);
>
> This making spi claims twice, since it's been doing before spi_xfer in
> below code. better to make it before the if.
>
Ok, I will call it from common place
--
Regards
Vignesh
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v2 04/11] mtd: spi: Port SPI NOR framework from Linux
2019-01-27 18:48 ` Jagan Teki
@ 2019-01-28 11:43 ` Vignesh R
0 siblings, 0 replies; 33+ messages in thread
From: Vignesh R @ 2019-01-28 11:43 UTC (permalink / raw)
To: u-boot
On 28/01/19 12:18 AM, Jagan Teki wrote:
> Do you have this whole series in some branch in github? I'm unable to
> apply it on master.
>
Here is my tentative v3 branch[1] based on top of today's master. I
haven't got to splitting up this patch yet. But have addressed all other
comments by you and Simon on this version.
[1] https://github.com/r-vignesh/u-boot.git branch: spi-nor-mig-patch-v3
Let me know if there are any additional comments. Thanks for the review!
> On Fri, Dec 21, 2018 at 12:15 PM Vignesh R <vigneshr@ti.com> wrote:
>>
>> Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
>> support 4 byte addressing opcodes, SFDP table parsing and different types of
>> quad mode enable sequences. Many newer flashes no longer support BANK
>> registers used by sf layer to a access >16MB space.
>> Also, many SPI controllers have special MMIO interfaces which provide
>> accelerated read/write access but require knowledge of flash parameters
>> to make use of it. Recent spi-mem layer provides a way to support such
>> flashes but sf layer isn't using that.
>> So sync SPI NOR framework from Linux v4.19 and add spi-mem support on top.
>> in order to gain 4 byte addressing support, SFDP support and a way to
>> support SPI controllers with MMIO flash interface.
>
> Understand the usage if direct complete sync, however it's difficult
> for me to review whole stuff. Can you please break into few patches
> like Basic sync, SFDP and other.
>
Ok, Let me see how that can be done.
>>
>> Signed-off-by: Vignesh R <vigneshr@ti.com>
>> ---
>> drivers/mtd/spi/spi-nor-core.c | 2590 ++++++++++++++++++++++++++++++++
>> include/linux/mtd/cfi.h | 32 +
>> include/linux/mtd/spi-nor.h | 410 +++++
>> 3 files changed, 3032 insertions(+)
>> create mode 100644 drivers/mtd/spi/spi-nor-core.c
>> create mode 100644 include/linux/mtd/cfi.h
>> create mode 100644 include/linux/mtd/spi-nor.h
>>
[...]
>> +static int spi_nor_sr_ready(struct spi_nor *nor)
>> +{
>> + int sr = read_sr(nor);
>> +
>> + if (sr < 0)
>> + return sr;
>> +
>> +#ifndef CONFIG_SPL_BUILD
>> + if (nor->flags & SNOR_F_USE_CLSR && sr & (SR_E_ERR | SR_P_ERR)) {
>> + if (sr & SR_E_ERR)
>> + dev_dbg(nor->dev, "Erase Error occurred\n");
>> + else
>> + dev_dbg(nor->dev, "Programming Error occurred\n");
>> +
>> + nor->write_reg(nor, SPINOR_OP_CLSR, NULL, 0);
>> + return -EIO;
>> + }
>> +#endif
>
> Does it increase SPL size? or do we always assume SPL can't access
> flash that would require CLSR?
>
Code size increase.. But now that we have SPI_FLASH_TINY, will drop this...
>> +
>> + return !(sr & SR_WIP);
>> +}
>> +
[...]
>> +enum spi_nor_read_command_index {
>> + SNOR_CMD_READ,
>> + SNOR_CMD_READ_FAST,
>> + SNOR_CMD_READ_1_1_1_DTR,
>> +
>> + /* Dual SPI */
>> + SNOR_CMD_READ_1_1_2,
>> + SNOR_CMD_READ_1_2_2,
>> + SNOR_CMD_READ_2_2_2,
>> + SNOR_CMD_READ_1_2_2_DTR,
>> +
>> + /* Quad SPI */
>> + SNOR_CMD_READ_1_1_4,
>> + SNOR_CMD_READ_1_4_4,
>> + SNOR_CMD_READ_4_4_4,
>> + SNOR_CMD_READ_1_4_4_DTR,
>> +
>> + /* Octo SPI */
>> + SNOR_CMD_READ_1_1_8,
>> + SNOR_CMD_READ_1_8_8,
>> + SNOR_CMD_READ_8_8_8,
>> + SNOR_CMD_READ_1_8_8_DTR,
>> +
>> + SNOR_CMD_READ_MAX
>> +};
>> +
>> +enum spi_nor_pp_command_index {
>> + SNOR_CMD_PP,
>> +
>> + /* Quad SPI */
>> + SNOR_CMD_PP_1_1_4,
>> + SNOR_CMD_PP_1_4_4,
>> + SNOR_CMD_PP_4_4_4,
>> +
>> + /* Octo SPI */
>> + SNOR_CMD_PP_1_1_8,
>> + SNOR_CMD_PP_1_8_8,
>> + SNOR_CMD_PP_8_8_8,
>> +
>> + SNOR_CMD_PP_MAX
>> +};
>
> I'm afraid whether we teatsed all thse combinations? or we doing for
> the sake of Linux sync?
>
Code exists for 1_1_1, 1_1_2, 1_1_4 and 4_4_4 modes and has been tested
(on par with current U-Boot SF stack). 1-2-2 and 1-4-4 should work with
SFDP(haven't tested it on a real hw though). Other modes are not
implemented (but exists as a result of sync up with Linux) and enums are
dummy definitions with no effect on code (are there for future use). I
can drop unused once if you prefer.
--
Regards
Vignesh
^ permalink raw reply [flat|nested] 33+ messages in thread
end of thread, other threads:[~2019-01-28 11:43 UTC | newest]
Thread overview: 33+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-12-21 6:38 [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 01/11] spi-mem: Claim SPI bus before spi mem access Vignesh R
2019-01-28 6:54 ` Jagan Teki
2019-01-28 9:44 ` Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 02/11] spi: Add non DM version of SPI_MEM Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 03/11] sh: bitops: add hweight*() macros Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 04/11] mtd: spi: Port SPI NOR framework from Linux Vignesh R
2019-01-27 18:48 ` Jagan Teki
2019-01-28 11:43 ` Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 05/11] mtd: spi: Switch to new SPI NOR framework Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 06/11] mtd: spi: Remove unused files Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 07/11] mtd: spi: Add lightweight SPI flash stack for SPL Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 08/11] configs: Enable SPI_FLASH_TINY for resource constrained boards Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 09/11] configs: Remove SF_DUAL_FLASH Vignesh R
2019-01-25 14:47 ` Jagan Teki
2019-01-25 15:01 ` Vignesh R
2019-01-28 6:36 ` Jagan Teki
2018-12-21 6:38 ` [U-Boot] [PATCH v2 10/11] configs: Don't use SPI_FLASH_BAR as default Vignesh R
2018-12-21 6:38 ` [U-Boot] [PATCH v2 11/11] MAINTAINERS: Add an entry for SPI NOR Vignesh R
2018-12-21 7:26 ` [U-Boot] [PATCH v2 00/11] SF: Migrate to Linux SPI NOR framework Stefan Roese
2018-12-21 10:33 ` Simon Goldschmidt
2018-12-21 11:11 ` Vignesh R
2018-12-21 13:29 ` Simon Goldschmidt
2018-12-22 7:43 ` Simon Goldschmidt
2019-01-09 9:26 ` Vignesh R
2019-01-14 15:02 ` Vignesh R
2019-01-14 15:05 ` Tom Rini
2019-01-21 11:58 ` Vignesh R
2019-01-21 12:10 ` Jagan Teki
2019-01-21 14:47 ` Vignesh R
2019-01-21 17:08 ` Tom Rini
2019-01-22 6:25 ` Stefan Roese
2019-01-21 17:14 ` Horatiu Vultur
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.