* [U-Boot] [PATCH v2 0/3] Add Beelink GS1 Board
@ 2019-04-12 14:15 Clément Péron
2019-04-12 14:15 ` [U-Boot] [PATCH v2 1/3] arm: dts: h6: sync with dts with Linux sunxi Clément Péron
` (2 more replies)
0 siblings, 3 replies; 7+ messages in thread
From: Clément Péron @ 2019-04-12 14:15 UTC (permalink / raw)
To: u-boot
This serie introduce the Beelink GS1 board with a patch for
the reset on Allwinner H6.
Thanks to Jagan Teki most of the Beelink GS1 device-tree is
taken from the Orange Pi boards.
Changes with v1:
- Add bus-width for mmc2 node
- Add sha1 in the sync dts commit
Clément Péron (3):
arm: dts: h6: sync with dts with Linux sunxi
arm: dts: h6: Add Beelink GS1 initial support
arm: sunxi: h6: fix reset using r_wdog
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun50i-h6-beelink-gs1.dts | 184 ++++++++++++++++++
arch/arm/dts/sun50i-h6-orangepi.dtsi | 2 -
arch/arm/dts/sun50i-h6-pine-h64.dts | 4 -
arch/arm/dts/sun50i-h6.dtsi | 16 +-
.../include/asm/arch-sunxi/cpu_sun50i_h6.h | 1 +
arch/arm/mach-sunxi/board.c | 9 +-
configs/beelink_gs1_defconfig | 15 ++
8 files changed, 218 insertions(+), 14 deletions(-)
create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts
create mode 100644 configs/beelink_gs1_defconfig
--
2.17.1
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v2 1/3] arm: dts: h6: sync with dts with Linux sunxi
2019-04-12 14:15 [U-Boot] [PATCH v2 0/3] Add Beelink GS1 Board Clément Péron
@ 2019-04-12 14:15 ` Clément Péron
2019-04-12 14:15 ` [U-Boot] [PATCH v2 2/3] arm: dts: h6: Add Beelink GS1 initial support Clément Péron
2019-04-12 14:15 ` [U-Boot] [PATCH v2 3/3] arm: sunxi: h6: fix reset using r_wdog Clément Péron
2 siblings, 0 replies; 7+ messages in thread
From: Clément Péron @ 2019-04-12 14:15 UTC (permalink / raw)
To: u-boot
There are some differences between U-Boot and Linux device tree files.
Sync only the minor changes.
6ba2e45d57af - arm64: dts: allwinner: h6: move MMC pinctrl to dtsi <Clément Péron>
54eac67bbe3a - arm64: dts: allwinner: Fix pinctrl node names <Maxime Ripard>
31af04cd60d3 - arm64: dts: Remove inconsistent use of 'arm,armv8' compatible string <Rob Herring>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
arch/arm/dts/sun50i-h6-orangepi.dtsi | 2 --
arch/arm/dts/sun50i-h6-pine-h64.dts | 4 ----
arch/arm/dts/sun50i-h6.dtsi | 16 ++++++++++------
3 files changed, 10 insertions(+), 12 deletions(-)
diff --git a/arch/arm/dts/sun50i-h6-orangepi.dtsi b/arch/arm/dts/sun50i-h6-orangepi.dtsi
index 0612c19cd9..3748dcaa70 100644
--- a/arch/arm/dts/sun50i-h6-orangepi.dtsi
+++ b/arch/arm/dts/sun50i-h6-orangepi.dtsi
@@ -24,8 +24,6 @@
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <®_cldo1>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
bus-width = <4>;
diff --git a/arch/arm/dts/sun50i-h6-pine-h64.dts b/arch/arm/dts/sun50i-h6-pine-h64.dts
index ceffc40810..a26314c084 100644
--- a/arch/arm/dts/sun50i-h6-pine-h64.dts
+++ b/arch/arm/dts/sun50i-h6-pine-h64.dts
@@ -42,16 +42,12 @@
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <®_cldo1>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
status = "okay";
};
&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <®_cldo1>;
vqmmc-supply = <®_bldo2>;
non-removable;
diff --git a/arch/arm/dts/sun50i-h6.dtsi b/arch/arm/dts/sun50i-h6.dtsi
index cfa5fffcf6..5f01314703 100644
--- a/arch/arm/dts/sun50i-h6.dtsi
+++ b/arch/arm/dts/sun50i-h6.dtsi
@@ -19,28 +19,28 @@
#size-cells = <0>;
cpu0: cpu at 0 {
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
device_type = "cpu";
reg = <0>;
enable-method = "psci";
};
cpu1: cpu at 1 {
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
device_type = "cpu";
reg = <1>;
enable-method = "psci";
};
cpu2: cpu at 2 {
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
device_type = "cpu";
reg = <2>;
enable-method = "psci";
};
cpu3: cpu at 3 {
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
device_type = "cpu";
reg = <3>;
enable-method = "psci";
@@ -143,7 +143,7 @@
bias-pull-up;
};
- uart0_ph_pins: uart0-ph {
+ uart0_ph_pins: uart0-ph-pins {
pins = "PH0", "PH1";
function = "uart0";
};
@@ -158,6 +158,8 @@
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -186,6 +188,8 @@
resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -266,7 +270,7 @@
interrupt-controller;
#interrupt-cells = <3>;
- r_i2c_pins: r-i2c {
+ r_i2c_pins: r-i2c-pins {
pins = "PL0", "PL1";
function = "s_i2c";
};
--
2.17.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v2 2/3] arm: dts: h6: Add Beelink GS1 initial support
2019-04-12 14:15 [U-Boot] [PATCH v2 0/3] Add Beelink GS1 Board Clément Péron
2019-04-12 14:15 ` [U-Boot] [PATCH v2 1/3] arm: dts: h6: sync with dts with Linux sunxi Clément Péron
@ 2019-04-12 14:15 ` Clément Péron
2019-04-14 17:29 ` Jagan Teki
2019-04-12 14:15 ` [U-Boot] [PATCH v2 3/3] arm: sunxi: h6: fix reset using r_wdog Clément Péron
2 siblings, 1 reply; 7+ messages in thread
From: Clément Péron @ 2019-04-12 14:15 UTC (permalink / raw)
To: u-boot
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun50i-h6-beelink-gs1.dts | 184 +++++++++++++++++++++++++
configs/beelink_gs1_defconfig | 15 ++
3 files changed, 200 insertions(+)
create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts
create mode 100644 configs/beelink_gs1_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 86a01c2c70..61e7156284 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -467,6 +467,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
sun50i-h5-orangepi-prime.dtb \
sun50i-h5-orangepi-zero-plus2.dtb
dtb-$(CONFIG_MACH_SUN50I_H6) += \
+ sun50i-h6-beelink-gs1.dtb \
sun50i-h6-orangepi-lite2.dtb \
sun50i-h6-orangepi-one-plus.dtb \
sun50i-h6-pine-h64.dtb
diff --git a/arch/arm/dts/sun50i-h6-beelink-gs1.dts b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
new file mode 100644
index 0000000000..54b0882bed
--- /dev/null
+++ b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
@@ -0,0 +1,184 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2019 Clément Péron <peron.clem@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h6.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Beelink GS1";
+ compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power {
+ label = "beelink:white:power";
+ gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
+ default-state = "on";
+ };
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the DC jack */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_cldo1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc2 {
+ vmmc-supply = <®_cldo1>;
+ vqmmc-supply = <®_bldo2>;
+ non-removable;
+ cap-mmc-hw-reset;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp805: pmic at 36 {
+ compatible = "x-powers,axp805", "x-powers,axp806";
+ reg = <0x36>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ x-powers,self-working-mode;
+ vina-supply = <®_vcc5v>;
+ vinb-supply = <®_vcc5v>;
+ vinc-supply = <®_vcc5v>;
+ vind-supply = <®_vcc5v>;
+ vine-supply = <®_vcc5v>;
+ aldoin-supply = <®_vcc5v>;
+ bldoin-supply = <®_vcc5v>;
+ cldoin-supply = <®_vcc5v>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ac200";
+ regulator-enable-ramp-delay = <100000>;
+ };
+
+ reg_aldo3: aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc25-dram";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-bias-pll";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-efuse-pcie-hdmi-io";
+ };
+
+ reg_bldo3: bldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dcxoio";
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ reg_cldo1: cldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-1";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <960000>;
+ regulator-max-microvolt = <960000>;
+ regulator-name = "vdd-sys";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+ };
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
diff --git a/configs/beelink_gs1_defconfig b/configs/beelink_gs1_defconfig
new file mode 100644
index 0000000000..ef4dd29549
--- /dev/null
+++ b/configs/beelink_gs1_defconfig
@@ -0,0 +1,15 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN50I_H6=y
+CONFIG_MMC0_CD_PIN="PF6"
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+# CONFIG_PSCI_RESET is not set
+CONFIG_NR_DRAM_BANKS=1
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-beelink-gs1"
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
--
2.17.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v2 3/3] arm: sunxi: h6: fix reset using r_wdog
2019-04-12 14:15 [U-Boot] [PATCH v2 0/3] Add Beelink GS1 Board Clément Péron
2019-04-12 14:15 ` [U-Boot] [PATCH v2 1/3] arm: dts: h6: sync with dts with Linux sunxi Clément Péron
2019-04-12 14:15 ` [U-Boot] [PATCH v2 2/3] arm: dts: h6: Add Beelink GS1 initial support Clément Péron
@ 2019-04-12 14:15 ` Clément Péron
2 siblings, 0 replies; 7+ messages in thread
From: Clément Péron @ 2019-04-12 14:15 UTC (permalink / raw)
To: u-boot
WDOG is broken for some H6 rev. The board is not
reseted correctly.
Use the R_WDOG instead.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h | 1 +
arch/arm/mach-sunxi/board.c | 9 +++++++--
2 files changed, 8 insertions(+), 2 deletions(-)
diff --git a/arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h b/arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h
index 41a9b0fc47..6392cb07b4 100644
--- a/arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h
+++ b/arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h
@@ -60,6 +60,7 @@
#define SUNXI_RTC_BASE 0x07000000
#define SUNXI_R_CPUCFG_BASE 0x07000400
#define SUNXI_PRCM_BASE 0x07010000
+#define SUNXI_R_WDOG_BASE 0x07020400
#define SUNXI_R_PIO_BASE 0x07022000
#define SUNXI_R_UART_BASE 0x07080000
#define SUNXI_R_TWI_BASE 0x07081400
diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c
index b74eaf2a0e..1075b5ca54 100644
--- a/arch/arm/mach-sunxi/board.c
+++ b/arch/arm/mach-sunxi/board.c
@@ -287,9 +287,14 @@ void reset_cpu(ulong addr)
writel(WDT_MODE_RESET_EN | WDT_MODE_EN, &wdog->mode);
}
#elif defined(CONFIG_SUNXI_GEN_SUN6I) || defined(CONFIG_MACH_SUN50I_H6)
+#if defined(CONFIG_MACH_SUN50I_H6)
+ /* WDOG is broken for some H6 rev. use the R_WDOG instead */
static const struct sunxi_wdog *wdog =
- ((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
-
+ (struct sunxi_wdog *)SUNXI_R_WDOG_BASE;
+#else
+ static const struct sunxi_wdog *wdog =
+ ((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
+#endif
/* Set the watchdog for its shortest interval (.5s) and wait */
writel(WDT_CFG_RESET, &wdog->cfg);
writel(WDT_MODE_EN, &wdog->mode);
--
2.17.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v2 2/3] arm: dts: h6: Add Beelink GS1 initial support
2019-04-12 14:15 ` [U-Boot] [PATCH v2 2/3] arm: dts: h6: Add Beelink GS1 initial support Clément Péron
@ 2019-04-14 17:29 ` Jagan Teki
2019-04-14 21:27 ` Clément Péron
0 siblings, 1 reply; 7+ messages in thread
From: Jagan Teki @ 2019-04-14 17:29 UTC (permalink / raw)
To: u-boot
On Fri, Apr 12, 2019 at 7:45 PM Clément Péron <peron.clem@gmail.com> wrote:
>
> Beelink GS1 is an Allwinner H6 based TV box,
> which support:
> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> - GPU Mali-T720
> - 2GB LPDDR3 RAM
> - 16GB eMMC
> - AXP805 PMIC
> - 1Gbps GMAC via RTL8211E
> - USB 2.0 and 3.0 Host
> - HDMI port
> - S/PDIF port
> - 5V/2A DC power supply
> - Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
Please dts sync commit details here.
>
> Signed-off-by: Clément Péron <peron.clem@gmail.com>
> ---
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/sun50i-h6-beelink-gs1.dts | 184 +++++++++++++++++++++++++
Seems like this has part of required nodes, sync the complete dts.
> configs/beelink_gs1_defconfig | 15 ++
Add entry on board/sunxi/MAINTAINERS
> 3 files changed, 200 insertions(+)
> create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts
> create mode 100644 configs/beelink_gs1_defconfig
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 86a01c2c70..61e7156284 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -467,6 +467,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
> sun50i-h5-orangepi-prime.dtb \
> sun50i-h5-orangepi-zero-plus2.dtb
> dtb-$(CONFIG_MACH_SUN50I_H6) += \
> + sun50i-h6-beelink-gs1.dtb \
> sun50i-h6-orangepi-lite2.dtb \
> sun50i-h6-orangepi-one-plus.dtb \
> sun50i-h6-pine-h64.dtb
> diff --git a/arch/arm/dts/sun50i-h6-beelink-gs1.dts b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> new file mode 100644
> index 0000000000..54b0882bed
> --- /dev/null
> +++ b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> @@ -0,0 +1,184 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2019 Clément Péron <peron.clem@gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h6.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "Beelink GS1";
> + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + power {
> + label = "beelink:white:power";
> + gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> + default-state = "on";
> + };
> + };
> +
> + reg_vcc5v: vcc5v {
> + /* board wide 5V supply directly from the DC jack */
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-5v";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +};
> +
> +&mmc0 {
> + vmmc-supply = <®_cldo1>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + vmmc-supply = <®_cldo1>;
> + vqmmc-supply = <®_bldo2>;
> + non-removable;
> + cap-mmc-hw-reset;
> + bus-width = <8>;
> + status = "okay";
> +};
> +
> +&r_i2c {
> + status = "okay";
> +
> + axp805: pmic at 36 {
> + compatible = "x-powers,axp805", "x-powers,axp806";
> + reg = <0x36>;
> + interrupt-parent = <&r_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + x-powers,self-working-mode;
> + vina-supply = <®_vcc5v>;
> + vinb-supply = <®_vcc5v>;
> + vinc-supply = <®_vcc5v>;
> + vind-supply = <®_vcc5v>;
> + vine-supply = <®_vcc5v>;
> + aldoin-supply = <®_vcc5v>;
> + bldoin-supply = <®_vcc5v>;
> + cldoin-supply = <®_vcc5v>;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-pl";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-ac200";
> + regulator-enable-ramp-delay = <100000>;
> + };
> +
> + reg_aldo3: aldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc25-dram";
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-bias-pll";
> + };
> +
> + reg_bldo2: bldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-efuse-pcie-hdmi-io";
> + };
> +
> + reg_bldo3: bldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-dcxoio";
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + reg_cldo1: cldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-3v3";
> + };
> +
> + reg_cldo2: cldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-1";
> + };
> +
> + reg_cldo3: cldo3 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-2";
> + };
> +
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-gpu";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <960000>;
> + regulator-max-microvolt = <960000>;
> + regulator-name = "vdd-sys";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-always-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vcc-dram";
> + };
> +
> + sw {
> + /* unused */
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_ph_pins>;
> + status = "okay";
> +};
> diff --git a/configs/beelink_gs1_defconfig b/configs/beelink_gs1_defconfig
> new file mode 100644
> index 0000000000..ef4dd29549
> --- /dev/null
> +++ b/configs/beelink_gs1_defconfig
> @@ -0,0 +1,15 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_SUNXI=y
> +CONFIG_SPL=y
> +CONFIG_MACH_SUN50I_H6=y
> +CONFIG_MMC0_CD_PIN="PF6"
> +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> +# CONFIG_PSCI_RESET is not set
> +CONFIG_NR_DRAM_BANKS=1
> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> +# CONFIG_CMD_FLASH is not set
> +# CONFIG_SPL_DOS_PARTITION is not set
> +# CONFIG_SPL_EFI_PARTITION is not set
> +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-beelink-gs1"
> +CONFIG_LED=y
> +CONFIG_LED_GPIO=y
Seems like most of Allwinner gpio's are gpio-leds. so select LED
(since it's dm led core) in arch/arm/Kconfig if LED_GPIO. I'm thinking
this could be proper assignment.
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v2 2/3] arm: dts: h6: Add Beelink GS1 initial support
2019-04-14 17:29 ` Jagan Teki
@ 2019-04-14 21:27 ` Clément Péron
2019-04-15 5:33 ` Jagan Teki
0 siblings, 1 reply; 7+ messages in thread
From: Clément Péron @ 2019-04-14 21:27 UTC (permalink / raw)
To: u-boot
Hi,
On Sun, 14 Apr 2019 at 19:29, Jagan Teki <jagan@amarulasolutions.com> wrote:
>
> On Fri, Apr 12, 2019 at 7:45 PM Clément Péron <peron.clem@gmail.com> wrote:
> >
> > Beelink GS1 is an Allwinner H6 based TV box,
> > which support:
> > - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> > - GPU Mali-T720
> > - 2GB LPDDR3 RAM
> > - 16GB eMMC
> > - AXP805 PMIC
> > - 1Gbps GMAC via RTL8211E
> > - USB 2.0 and 3.0 Host
> > - HDMI port
> > - S/PDIF port
> > - 5V/2A DC power supply
> > - Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
>
> Please dts sync commit details here.
>
> >
> > Signed-off-by: Clément Péron <peron.clem@gmail.com>
> > ---
> > arch/arm/dts/Makefile | 1 +
> > arch/arm/dts/sun50i-h6-beelink-gs1.dts | 184 +++++++++++++++++++++++++
>
> Seems like this has part of required nodes, sync the complete dts.
Ok so you want to add the complete dts from linux.
I think only IP used in U-boot are needed.
I will do that in v3
>
> > configs/beelink_gs1_defconfig | 15 ++
>
> Add entry on board/sunxi/MAINTAINERS
Ok
>
> > 3 files changed, 200 insertions(+)
> > create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts
> > create mode 100644 configs/beelink_gs1_defconfig
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > index 86a01c2c70..61e7156284 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -467,6 +467,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
> > sun50i-h5-orangepi-prime.dtb \
> > sun50i-h5-orangepi-zero-plus2.dtb
> > dtb-$(CONFIG_MACH_SUN50I_H6) += \
> > + sun50i-h6-beelink-gs1.dtb \
> > sun50i-h6-orangepi-lite2.dtb \
> > sun50i-h6-orangepi-one-plus.dtb \
> > sun50i-h6-pine-h64.dtb
> > diff --git a/arch/arm/dts/sun50i-h6-beelink-gs1.dts b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> > new file mode 100644
> > index 0000000000..54b0882bed
> > --- /dev/null
> > +++ b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> > @@ -0,0 +1,184 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> > +/*
> > + * Copyright (C) 2019 Clément Péron <peron.clem@gmail.com>
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "sun50i-h6.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +
> > +/ {
> > + model = "Beelink GS1";
> > + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
> > +
> > + aliases {
> > + serial0 = &uart0;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + power {
> > + label = "beelink:white:power";
> > + gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> > + default-state = "on";
> > + };
> > + };
> > +
> > + reg_vcc5v: vcc5v {
> > + /* board wide 5V supply directly from the DC jack */
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc-5v";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
> > + };
> > +};
> > +
> > +&mmc0 {
> > + vmmc-supply = <®_cldo1>;
> > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> > + bus-width = <4>;
> > + status = "okay";
> > +};
> > +
> > +&mmc2 {
> > + vmmc-supply = <®_cldo1>;
> > + vqmmc-supply = <®_bldo2>;
> > + non-removable;
> > + cap-mmc-hw-reset;
> > + bus-width = <8>;
> > + status = "okay";
> > +};
> > +
> > +&r_i2c {
> > + status = "okay";
> > +
> > + axp805: pmic at 36 {
> > + compatible = "x-powers,axp805", "x-powers,axp806";
> > + reg = <0x36>;
> > + interrupt-parent = <&r_intc>;
> > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + x-powers,self-working-mode;
> > + vina-supply = <®_vcc5v>;
> > + vinb-supply = <®_vcc5v>;
> > + vinc-supply = <®_vcc5v>;
> > + vind-supply = <®_vcc5v>;
> > + vine-supply = <®_vcc5v>;
> > + aldoin-supply = <®_vcc5v>;
> > + bldoin-supply = <®_vcc5v>;
> > + cldoin-supply = <®_vcc5v>;
> > +
> > + regulators {
> > + reg_aldo1: aldo1 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-pl";
> > + };
> > +
> > + reg_aldo2: aldo2 {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-ac200";
> > + regulator-enable-ramp-delay = <100000>;
> > + };
> > +
> > + reg_aldo3: aldo3 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc25-dram";
> > + };
> > +
> > + reg_bldo1: bldo1 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-name = "vcc-bias-pll";
> > + };
> > +
> > + reg_bldo2: bldo2 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-name = "vcc-efuse-pcie-hdmi-io";
> > + };
> > +
> > + reg_bldo3: bldo3 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-name = "vcc-dcxoio";
> > + };
> > +
> > + bldo4 {
> > + /* unused */
> > + };
> > +
> > + reg_cldo1: cldo1 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-3v3";
> > + };
> > +
> > + reg_cldo2: cldo2 {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-wifi-1";
> > + };
> > +
> > + reg_cldo3: cldo3 {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-wifi-2";
> > + };
> > +
> > + reg_dcdca: dcdca {
> > + regulator-always-on;
> > + regulator-min-microvolt = <810000>;
> > + regulator-max-microvolt = <1080000>;
> > + regulator-name = "vdd-cpu";
> > + };
> > +
> > + reg_dcdcc: dcdcc {
> > + regulator-min-microvolt = <810000>;
> > + regulator-max-microvolt = <1080000>;
> > + regulator-name = "vdd-gpu";
> > + };
> > +
> > + reg_dcdcd: dcdcd {
> > + regulator-always-on;
> > + regulator-min-microvolt = <960000>;
> > + regulator-max-microvolt = <960000>;
> > + regulator-name = "vdd-sys";
> > + };
> > +
> > + reg_dcdce: dcdce {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-name = "vcc-dram";
> > + };
> > +
> > + sw {
> > + /* unused */
> > + };
> > + };
> > + };
> > +};
> > +
> > +&uart0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart0_ph_pins>;
> > + status = "okay";
> > +};
> > diff --git a/configs/beelink_gs1_defconfig b/configs/beelink_gs1_defconfig
> > new file mode 100644
> > index 0000000000..ef4dd29549
> > --- /dev/null
> > +++ b/configs/beelink_gs1_defconfig
> > @@ -0,0 +1,15 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_SUNXI=y
> > +CONFIG_SPL=y
> > +CONFIG_MACH_SUN50I_H6=y
> > +CONFIG_MMC0_CD_PIN="PF6"
> > +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> > +# CONFIG_PSCI_RESET is not set
> > +CONFIG_NR_DRAM_BANKS=1
> > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > +# CONFIG_CMD_FLASH is not set
> > +# CONFIG_SPL_DOS_PARTITION is not set
> > +# CONFIG_SPL_EFI_PARTITION is not set
> > +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-beelink-gs1"
> > +CONFIG_LED=y
> > +CONFIG_LED_GPIO=y
>
> Seems like most of Allwinner gpio's are gpio-leds. so select LED
> (since it's dm led core) in arch/arm/Kconfig if LED_GPIO. I'm thinking
> this could be proper assignment.
We can't do that as LED_GPIO depends on LED.
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v2 2/3] arm: dts: h6: Add Beelink GS1 initial support
2019-04-14 21:27 ` Clément Péron
@ 2019-04-15 5:33 ` Jagan Teki
0 siblings, 0 replies; 7+ messages in thread
From: Jagan Teki @ 2019-04-15 5:33 UTC (permalink / raw)
To: u-boot
On Mon, Apr 15, 2019 at 2:58 AM Clément Péron <peron.clem@gmail.com> wrote:
>
> Hi,
>
> On Sun, 14 Apr 2019 at 19:29, Jagan Teki <jagan@amarulasolutions.com> wrote:
> >
> > On Fri, Apr 12, 2019 at 7:45 PM Clément Péron <peron.clem@gmail.com> wrote:
> > >
> > > Beelink GS1 is an Allwinner H6 based TV box,
> > > which support:
> > > - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> > > - GPU Mali-T720
> > > - 2GB LPDDR3 RAM
> > > - 16GB eMMC
> > > - AXP805 PMIC
> > > - 1Gbps GMAC via RTL8211E
> > > - USB 2.0 and 3.0 Host
> > > - HDMI port
> > > - S/PDIF port
> > > - 5V/2A DC power supply
> > > - Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
> >
> > Please dts sync commit details here.
> >
> > >
> > > Signed-off-by: Clément Péron <peron.clem@gmail.com>
> > > ---
> > > arch/arm/dts/Makefile | 1 +
> > > arch/arm/dts/sun50i-h6-beelink-gs1.dts | 184 +++++++++++++++++++++++++
> >
> > Seems like this has part of required nodes, sync the complete dts.
>
> Ok so you want to add the complete dts from linux.
>
> I think only IP used in U-boot are needed.
>
> I will do that in v3
>
> >
> > > configs/beelink_gs1_defconfig | 15 ++
> >
> > Add entry on board/sunxi/MAINTAINERS
>
> Ok
>
> >
> > > 3 files changed, 200 insertions(+)
> > > create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts
> > > create mode 100644 configs/beelink_gs1_defconfig
> > >
> > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > > index 86a01c2c70..61e7156284 100644
> > > --- a/arch/arm/dts/Makefile
> > > +++ b/arch/arm/dts/Makefile
> > > @@ -467,6 +467,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
> > > sun50i-h5-orangepi-prime.dtb \
> > > sun50i-h5-orangepi-zero-plus2.dtb
> > > dtb-$(CONFIG_MACH_SUN50I_H6) += \
> > > + sun50i-h6-beelink-gs1.dtb \
> > > sun50i-h6-orangepi-lite2.dtb \
> > > sun50i-h6-orangepi-one-plus.dtb \
> > > sun50i-h6-pine-h64.dtb
> > > diff --git a/arch/arm/dts/sun50i-h6-beelink-gs1.dts b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> > > new file mode 100644
> > > index 0000000000..54b0882bed
> > > --- /dev/null
> > > +++ b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> > > @@ -0,0 +1,184 @@
> > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> > > +/*
> > > + * Copyright (C) 2019 Clément Péron <peron.clem@gmail.com>
> > > + */
> > > +
> > > +/dts-v1/;
> > > +
> > > +#include "sun50i-h6.dtsi"
> > > +
> > > +#include <dt-bindings/gpio/gpio.h>
> > > +
> > > +/ {
> > > + model = "Beelink GS1";
> > > + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
> > > +
> > > + aliases {
> > > + serial0 = &uart0;
> > > + };
> > > +
> > > + chosen {
> > > + stdout-path = "serial0:115200n8";
> > > + };
> > > +
> > > + leds {
> > > + compatible = "gpio-leds";
> > > +
> > > + power {
> > > + label = "beelink:white:power";
> > > + gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> > > + default-state = "on";
> > > + };
> > > + };
> > > +
> > > + reg_vcc5v: vcc5v {
> > > + /* board wide 5V supply directly from the DC jack */
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "vcc-5v";
> > > + regulator-min-microvolt = <5000000>;
> > > + regulator-max-microvolt = <5000000>;
> > > + regulator-always-on;
> > > + };
> > > +};
> > > +
> > > +&mmc0 {
> > > + vmmc-supply = <®_cldo1>;
> > > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> > > + bus-width = <4>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&mmc2 {
> > > + vmmc-supply = <®_cldo1>;
> > > + vqmmc-supply = <®_bldo2>;
> > > + non-removable;
> > > + cap-mmc-hw-reset;
> > > + bus-width = <8>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&r_i2c {
> > > + status = "okay";
> > > +
> > > + axp805: pmic at 36 {
> > > + compatible = "x-powers,axp805", "x-powers,axp806";
> > > + reg = <0x36>;
> > > + interrupt-parent = <&r_intc>;
> > > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> > > + interrupt-controller;
> > > + #interrupt-cells = <1>;
> > > + x-powers,self-working-mode;
> > > + vina-supply = <®_vcc5v>;
> > > + vinb-supply = <®_vcc5v>;
> > > + vinc-supply = <®_vcc5v>;
> > > + vind-supply = <®_vcc5v>;
> > > + vine-supply = <®_vcc5v>;
> > > + aldoin-supply = <®_vcc5v>;
> > > + bldoin-supply = <®_vcc5v>;
> > > + cldoin-supply = <®_vcc5v>;
> > > +
> > > + regulators {
> > > + reg_aldo1: aldo1 {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <3300000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-name = "vcc-pl";
> > > + };
> > > +
> > > + reg_aldo2: aldo2 {
> > > + regulator-min-microvolt = <3300000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-name = "vcc-ac200";
> > > + regulator-enable-ramp-delay = <100000>;
> > > + };
> > > +
> > > + reg_aldo3: aldo3 {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <3300000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-name = "vcc25-dram";
> > > + };
> > > +
> > > + reg_bldo1: bldo1 {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> > > + regulator-name = "vcc-bias-pll";
> > > + };
> > > +
> > > + reg_bldo2: bldo2 {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> > > + regulator-name = "vcc-efuse-pcie-hdmi-io";
> > > + };
> > > +
> > > + reg_bldo3: bldo3 {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> > > + regulator-name = "vcc-dcxoio";
> > > + };
> > > +
> > > + bldo4 {
> > > + /* unused */
> > > + };
> > > +
> > > + reg_cldo1: cldo1 {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <3300000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-name = "vcc-3v3";
> > > + };
> > > +
> > > + reg_cldo2: cldo2 {
> > > + regulator-min-microvolt = <3300000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-name = "vcc-wifi-1";
> > > + };
> > > +
> > > + reg_cldo3: cldo3 {
> > > + regulator-min-microvolt = <3300000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-name = "vcc-wifi-2";
> > > + };
> > > +
> > > + reg_dcdca: dcdca {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <810000>;
> > > + regulator-max-microvolt = <1080000>;
> > > + regulator-name = "vdd-cpu";
> > > + };
> > > +
> > > + reg_dcdcc: dcdcc {
> > > + regulator-min-microvolt = <810000>;
> > > + regulator-max-microvolt = <1080000>;
> > > + regulator-name = "vdd-gpu";
> > > + };
> > > +
> > > + reg_dcdcd: dcdcd {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <960000>;
> > > + regulator-max-microvolt = <960000>;
> > > + regulator-name = "vdd-sys";
> > > + };
> > > +
> > > + reg_dcdce: dcdce {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <1200000>;
> > > + regulator-max-microvolt = <1200000>;
> > > + regulator-name = "vcc-dram";
> > > + };
> > > +
> > > + sw {
> > > + /* unused */
> > > + };
> > > + };
> > > + };
> > > +};
> > > +
> > > +&uart0 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&uart0_ph_pins>;
> > > + status = "okay";
> > > +};
> > > diff --git a/configs/beelink_gs1_defconfig b/configs/beelink_gs1_defconfig
> > > new file mode 100644
> > > index 0000000000..ef4dd29549
> > > --- /dev/null
> > > +++ b/configs/beelink_gs1_defconfig
> > > @@ -0,0 +1,15 @@
> > > +CONFIG_ARM=y
> > > +CONFIG_ARCH_SUNXI=y
> > > +CONFIG_SPL=y
> > > +CONFIG_MACH_SUN50I_H6=y
> > > +CONFIG_MMC0_CD_PIN="PF6"
> > > +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> > > +# CONFIG_PSCI_RESET is not set
> > > +CONFIG_NR_DRAM_BANKS=1
> > > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > > +# CONFIG_CMD_FLASH is not set
> > > +# CONFIG_SPL_DOS_PARTITION is not set
> > > +# CONFIG_SPL_EFI_PARTITION is not set
> > > +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-beelink-gs1"
> > > +CONFIG_LED=y
> > > +CONFIG_LED_GPIO=y
> >
> > Seems like most of Allwinner gpio's are gpio-leds. so select LED
> > (since it's dm led core) in arch/arm/Kconfig if LED_GPIO. I'm thinking
> > this could be proper assignment.
>
> We can't do that as LED_GPIO depends on LED.
True.
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2019-04-15 5:33 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-04-12 14:15 [U-Boot] [PATCH v2 0/3] Add Beelink GS1 Board Clément Péron
2019-04-12 14:15 ` [U-Boot] [PATCH v2 1/3] arm: dts: h6: sync with dts with Linux sunxi Clément Péron
2019-04-12 14:15 ` [U-Boot] [PATCH v2 2/3] arm: dts: h6: Add Beelink GS1 initial support Clément Péron
2019-04-14 17:29 ` Jagan Teki
2019-04-14 21:27 ` Clément Péron
2019-04-15 5:33 ` Jagan Teki
2019-04-12 14:15 ` [U-Boot] [PATCH v2 3/3] arm: sunxi: h6: fix reset using r_wdog Clément Péron
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.