From: <Tudor.Ambarus@microchip.com>
To: <alexandre.belloni@bootlin.com>,
<Ludovic.Desroches@microchip.com>, <Nicolas.Ferre@microchip.com>
Cc: <robh+dt@kernel.org>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <Codrin.Ciubotariu@microchip.com>,
<Tudor.Ambarus@microchip.com>
Subject: [PATCH 01/16] ARM: dts: at91: sama5d2: Fix the label numbering for flexcom functions
Date: Thu, 14 May 2020 05:03:07 +0000 [thread overview]
Message-ID: <20200514050301.147442-2-tudor.ambarus@microchip.com> (raw)
In-Reply-To: <20200514050301.147442-1-tudor.ambarus@microchip.com>
From: Tudor Ambarus <tudor.ambarus@microchip.com>
The sama5d2 SoC has the following IPs: [uart0, uart4], {spi0, spi1}, {i2c0, i2c1}.
Label the flexcom functions in order:
flx0: uart5, spi2, i2c2
flx1: uart6, spi3, i2c3
flx2: uart7, spi4, i2c4
flx3: uart8, spi5, i2c5
flx4: uart9, spi6, i2c6
Some boards respected this scheme, others not. Fix the ones that didn't.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
---
arch/arm/boot/dts/at91-kizbox3-hs.dts | 4 ++--
arch/arm/boot/dts/at91-kizbox3_common.dtsi | 8 ++++----
arch/arm/boot/dts/at91-sama5d27_som1_ek.dts | 20 ++++++++++----------
arch/arm/boot/dts/at91-sama5d2_icp.dts | 8 ++++----
arch/arm/boot/dts/at91-sama5d2_xplained.dts | 2 +-
5 files changed, 21 insertions(+), 21 deletions(-)
diff --git a/arch/arm/boot/dts/at91-kizbox3-hs.dts b/arch/arm/boot/dts/at91-kizbox3-hs.dts
index 8734e7f8939e..0da1f0557eaf 100644
--- a/arch/arm/boot/dts/at91-kizbox3-hs.dts
+++ b/arch/arm/boot/dts/at91-kizbox3-hs.dts
@@ -283,7 +283,7 @@
&flx3 {
status = "okay";
- uart6: serial@200 {
+ uart8: serial@200 {
status = "okay";
};
};
@@ -291,7 +291,7 @@
&flx4 {
status = "okay";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
status = "okay";
};
};
diff --git a/arch/arm/boot/dts/at91-kizbox3_common.dtsi b/arch/arm/boot/dts/at91-kizbox3_common.dtsi
index 299e74d23184..d7a6c972bdac 100644
--- a/arch/arm/boot/dts/at91-kizbox3_common.dtsi
+++ b/arch/arm/boot/dts/at91-kizbox3_common.dtsi
@@ -28,7 +28,7 @@
serial3 = &uart3;
serial4 = &uart4;
serial5 = &uart5;
- serial6 = &uart6;
+ serial6 = &uart8;
};
chosen {
@@ -207,7 +207,7 @@
};
};
- pinctrl_flx4_default: flx4_i2c2_default {
+ pinctrl_flx4_default: flx4_i2c6_default {
pinmux = <PIN_PD12__FLEXCOM4_IO0>, //DATA
<PIN_PD13__FLEXCOM4_IO1>; //CLK
bias-disable;
@@ -324,7 +324,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
status = "disabled";
- uart6: serial@200 {
+ uart8: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x400>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -350,7 +350,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "disabled";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
diff --git a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
index b0853bf7901c..d215243fe163 100644
--- a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
@@ -21,7 +21,7 @@
serial1 = &uart4; /* mikro BUS 1 */
serial2 = &uart2; /* mikro BUS 2 */
i2c1 = &i2c1;
- i2c2 = &i2c2;
+ i2c2 = &i2c3;
};
chosen {
@@ -125,7 +125,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
- i2c2: i2c@600 {
+ i2c3: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -178,7 +178,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
status = "disabled";
- uart7: serial@200 {
+ uart8: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -190,7 +190,7 @@
status = "disabled"; /* Conflict with isc. */
};
- spi2: spi@400 {
+ spi5: spi@400 {
compatible = "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -207,7 +207,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
status = "okay";
- uart6: serial@200 {
+ uart9: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -216,10 +216,10 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
atmel,fifo-size = <32>;
- status = "disabled"; /* Conflict with spi3 and i2c3. */
+ status = "disabled"; /* Conflict with spi6 and i2c6. */
};
- spi3: spi@400 {
+ spi6: spi@400 {
compatible = "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -228,10 +228,10 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mikrobus_spi &pinctrl_mikrobus1_spi_cs &pinctrl_mikrobus2_spi_cs>;
atmel,fifo-size = <16>;
- status = "okay"; /* Conflict with uart6 and i2c3. */
+ status = "okay"; /* Conflict with uart5 and i2c6. */
};
- i2c3: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -243,7 +243,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
atmel,fifo-size = <16>;
- status = "disabled"; /* Conflict with uart6 and spi3. */
+ status = "disabled"; /* Conflict with uart5 and spi6. */
};
};
diff --git a/arch/arm/boot/dts/at91-sama5d2_icp.dts b/arch/arm/boot/dts/at91-sama5d2_icp.dts
index cc9fa700eafb..1d9556dbbd63 100644
--- a/arch/arm/boot/dts/at91-sama5d2_icp.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_icp.dts
@@ -22,7 +22,7 @@
serial0 = &uart0; /* debug uart0 + mikro BUS 1 */
serial1 = &uart1; /* mikro BUS 3 */
serial3 = &uart3; /* mikro BUS 2 */
- serial5 = &uart5; /* flx2 */
+ serial5 = &uart7; /* flx2 */
i2c0 = &i2c0;
i2c1 = &i2c1;
};
@@ -159,7 +159,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
status = "okay";
- uart5: serial@200 {
+ uart7: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <21 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -184,7 +184,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
status = "okay";
- spi3: spi@400 {
+ spi5: spi@400 {
compatible = "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -201,7 +201,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index e0c6cff1a312..0666708b05f9 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -377,7 +377,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
--
2.23.0
WARNING: multiple messages have this Message-ID (diff)
From: <Tudor.Ambarus@microchip.com>
To: <alexandre.belloni@bootlin.com>,
<Ludovic.Desroches@microchip.com>, <Nicolas.Ferre@microchip.com>
Cc: devicetree@vger.kernel.org, Tudor.Ambarus@microchip.com,
linux-kernel@vger.kernel.org, robh+dt@kernel.org,
Codrin.Ciubotariu@microchip.com,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH 01/16] ARM: dts: at91: sama5d2: Fix the label numbering for flexcom functions
Date: Thu, 14 May 2020 05:03:07 +0000 [thread overview]
Message-ID: <20200514050301.147442-2-tudor.ambarus@microchip.com> (raw)
In-Reply-To: <20200514050301.147442-1-tudor.ambarus@microchip.com>
From: Tudor Ambarus <tudor.ambarus@microchip.com>
The sama5d2 SoC has the following IPs: [uart0, uart4], {spi0, spi1}, {i2c0, i2c1}.
Label the flexcom functions in order:
flx0: uart5, spi2, i2c2
flx1: uart6, spi3, i2c3
flx2: uart7, spi4, i2c4
flx3: uart8, spi5, i2c5
flx4: uart9, spi6, i2c6
Some boards respected this scheme, others not. Fix the ones that didn't.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
---
arch/arm/boot/dts/at91-kizbox3-hs.dts | 4 ++--
arch/arm/boot/dts/at91-kizbox3_common.dtsi | 8 ++++----
arch/arm/boot/dts/at91-sama5d27_som1_ek.dts | 20 ++++++++++----------
arch/arm/boot/dts/at91-sama5d2_icp.dts | 8 ++++----
arch/arm/boot/dts/at91-sama5d2_xplained.dts | 2 +-
5 files changed, 21 insertions(+), 21 deletions(-)
diff --git a/arch/arm/boot/dts/at91-kizbox3-hs.dts b/arch/arm/boot/dts/at91-kizbox3-hs.dts
index 8734e7f8939e..0da1f0557eaf 100644
--- a/arch/arm/boot/dts/at91-kizbox3-hs.dts
+++ b/arch/arm/boot/dts/at91-kizbox3-hs.dts
@@ -283,7 +283,7 @@
&flx3 {
status = "okay";
- uart6: serial@200 {
+ uart8: serial@200 {
status = "okay";
};
};
@@ -291,7 +291,7 @@
&flx4 {
status = "okay";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
status = "okay";
};
};
diff --git a/arch/arm/boot/dts/at91-kizbox3_common.dtsi b/arch/arm/boot/dts/at91-kizbox3_common.dtsi
index 299e74d23184..d7a6c972bdac 100644
--- a/arch/arm/boot/dts/at91-kizbox3_common.dtsi
+++ b/arch/arm/boot/dts/at91-kizbox3_common.dtsi
@@ -28,7 +28,7 @@
serial3 = &uart3;
serial4 = &uart4;
serial5 = &uart5;
- serial6 = &uart6;
+ serial6 = &uart8;
};
chosen {
@@ -207,7 +207,7 @@
};
};
- pinctrl_flx4_default: flx4_i2c2_default {
+ pinctrl_flx4_default: flx4_i2c6_default {
pinmux = <PIN_PD12__FLEXCOM4_IO0>, //DATA
<PIN_PD13__FLEXCOM4_IO1>; //CLK
bias-disable;
@@ -324,7 +324,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
status = "disabled";
- uart6: serial@200 {
+ uart8: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x400>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -350,7 +350,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "disabled";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
diff --git a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
index b0853bf7901c..d215243fe163 100644
--- a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
@@ -21,7 +21,7 @@
serial1 = &uart4; /* mikro BUS 1 */
serial2 = &uart2; /* mikro BUS 2 */
i2c1 = &i2c1;
- i2c2 = &i2c2;
+ i2c2 = &i2c3;
};
chosen {
@@ -125,7 +125,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
- i2c2: i2c@600 {
+ i2c3: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -178,7 +178,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
status = "disabled";
- uart7: serial@200 {
+ uart8: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -190,7 +190,7 @@
status = "disabled"; /* Conflict with isc. */
};
- spi2: spi@400 {
+ spi5: spi@400 {
compatible = "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -207,7 +207,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
status = "okay";
- uart6: serial@200 {
+ uart9: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -216,10 +216,10 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
atmel,fifo-size = <32>;
- status = "disabled"; /* Conflict with spi3 and i2c3. */
+ status = "disabled"; /* Conflict with spi6 and i2c6. */
};
- spi3: spi@400 {
+ spi6: spi@400 {
compatible = "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -228,10 +228,10 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mikrobus_spi &pinctrl_mikrobus1_spi_cs &pinctrl_mikrobus2_spi_cs>;
atmel,fifo-size = <16>;
- status = "okay"; /* Conflict with uart6 and i2c3. */
+ status = "okay"; /* Conflict with uart5 and i2c6. */
};
- i2c3: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -243,7 +243,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
atmel,fifo-size = <16>;
- status = "disabled"; /* Conflict with uart6 and spi3. */
+ status = "disabled"; /* Conflict with uart5 and spi6. */
};
};
diff --git a/arch/arm/boot/dts/at91-sama5d2_icp.dts b/arch/arm/boot/dts/at91-sama5d2_icp.dts
index cc9fa700eafb..1d9556dbbd63 100644
--- a/arch/arm/boot/dts/at91-sama5d2_icp.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_icp.dts
@@ -22,7 +22,7 @@
serial0 = &uart0; /* debug uart0 + mikro BUS 1 */
serial1 = &uart1; /* mikro BUS 3 */
serial3 = &uart3; /* mikro BUS 2 */
- serial5 = &uart5; /* flx2 */
+ serial5 = &uart7; /* flx2 */
i2c0 = &i2c0;
i2c1 = &i2c1;
};
@@ -159,7 +159,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
status = "okay";
- uart5: serial@200 {
+ uart7: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <21 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -184,7 +184,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
status = "okay";
- spi3: spi@400 {
+ spi5: spi@400 {
compatible = "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -201,7 +201,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index e0c6cff1a312..0666708b05f9 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -377,7 +377,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
- i2c2: i2c@600 {
+ i2c6: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
--
2.23.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-05-14 5:03 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-14 5:03 [PATCH 00/16] ARM: dts: at91: sama5d2: Rework Flexcom definitions Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus [this message]
2020-05-14 5:03 ` [PATCH 01/16] ARM: dts: at91: sama5d2: Fix the label numbering for flexcom functions Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 02/16] ARM: dts: at91: sama5d2: Move flx4 definitions in the SoC dtsi Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 03/16] ARM: dts: at91: sama5d2: Move flx3 " Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 04/16] ARM: dts: at91: sama5d2: Move flx2 " Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 05/16] ARM: dts: at91: sama5d2: Move flx1 " Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 06/16] ARM: dts: at91: sama5d2: Move flx0 " Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 07/16] ARM: dts: at91: sama5d2: Specify the FIFO size for the Flexcom UART Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 09/16] ARM: dts: at91: sama5d2: Add DMA bindings for the flx3 SPI function Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 08/16] ARM: dts: at91: sama5d2: Add DMA bindings for the SPI and UART flx4 functions Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 10/16] ARM: dts: at91: sama5d2: Add DMA bindings for the flx1 I2C function Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 11/16] ARM: dts: at91: sama5d2: Add DMA bindings for the SPI and I2C flx0 functions Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 13/16] ARM: dts: at91: sama5d2: Remove i2s and tcb aliases from SoC dtsi Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 12/16] ARM: dts: at91: sama5d2: Add missing flexcom definitions Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 14/16] ARM: dts: at91: sama5d2_xplained: Add alias for DBGU Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 16/16] ARM: dts: at91: sama5d2_ptc_ek: Add comments to describe the aliases Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-14 5:03 ` [PATCH 15/16] ARM: dts: at91: sama5d2_xplained: Describe the flx0 I2C function Tudor.Ambarus
2020-05-14 5:03 ` Tudor.Ambarus
2020-05-15 14:51 ` [PATCH 00/16] ARM: dts: at91: sama5d2: Rework Flexcom definitions Alexandre Belloni
2020-05-15 14:51 ` Alexandre Belloni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200514050301.147442-2-tudor.ambarus@microchip.com \
--to=tudor.ambarus@microchip.com \
--cc=Codrin.Ciubotariu@microchip.com \
--cc=Ludovic.Desroches@microchip.com \
--cc=Nicolas.Ferre@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.