All of lore.kernel.org
 help / color / mirror / Atom feed
From: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
To: Matt Roper <matthew.d.roper@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Subject: Re: [Intel-gfx] [PATCH v3 09/15] drm/i915/rkl: Don't try to access transcoder D
Date: Thu, 4 Jun 2020 19:55:29 +0300	[thread overview]
Message-ID: <20200604165529.GW6112@intel.com> (raw)
In-Reply-To: <20200603211529.3005059-10-matthew.d.roper@intel.com>

On Wed, Jun 03, 2020 at 02:15:23PM -0700, Matt Roper wrote:
> There are a couple places in our driver that loop over transcoders A..D
> for gen11+; since RKL only has three pipes/transcoders, this can lead to
> unclaimed register reads/writes.  We should add checks for transcoder
> existence where appropriate.
> 
> v2: Move one transcoder check that wound up in the wrong function after
>     conflict resolution.  It belongs in bdw_get_trans_port_sync_config
>     rather than bxt_get_dsi_transcoder_state.
> 
> v3: Switch loops to use for_each_cpu_transcoder_masked() since this
>     iterator already checks the platform's transcoder mask for us.
>     (Ville)
> 
> Cc: Aditya Swarup <aditya.swarup@intel.com>
> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
> Signed-off-by: Matt Roper <matthew.d.roper@intel.com>

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

> ---
>  drivers/gpu/drm/i915/i915_irq.c | 8 ++++++--
>  1 file changed, 6 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
> index f3ea81a17352..40a71c4a1ef5 100644
> --- a/drivers/gpu/drm/i915/i915_irq.c
> +++ b/drivers/gpu/drm/i915/i915_irq.c
> @@ -2885,13 +2885,15 @@ static void gen11_display_irq_reset(struct drm_i915_private *dev_priv)
>  {
>  	struct intel_uncore *uncore = &dev_priv->uncore;
>  	enum pipe pipe;
> +	u32 trans_mask = BIT(TRANSCODER_A) | BIT(TRANSCODER_B) |
> +		BIT(TRANSCODER_C) | BIT(TRANSCODER_D);
>  
>  	intel_uncore_write(uncore, GEN11_DISPLAY_INT_CTL, 0);
>  
>  	if (INTEL_GEN(dev_priv) >= 12) {
>  		enum transcoder trans;
>  
> -		for (trans = TRANSCODER_A; trans <= TRANSCODER_D; trans++) {
> +		for_each_cpu_transcoder_masked(dev_priv, trans, trans_mask) {
>  			enum intel_display_power_domain domain;
>  
>  			domain = POWER_DOMAIN_TRANSCODER(trans);
> @@ -3413,6 +3415,8 @@ static void gen8_de_irq_postinstall(struct drm_i915_private *dev_priv)
>  	u32 de_port_masked = gen8_de_port_aux_mask(dev_priv);
>  	u32 de_port_enables;
>  	u32 de_misc_masked = GEN8_DE_EDP_PSR;
> +	u32 trans_mask = BIT(TRANSCODER_A) | BIT(TRANSCODER_B) |
> +		BIT(TRANSCODER_C) | BIT(TRANSCODER_D);
>  	enum pipe pipe;
>  
>  	if (INTEL_GEN(dev_priv) <= 10)
> @@ -3433,7 +3437,7 @@ static void gen8_de_irq_postinstall(struct drm_i915_private *dev_priv)
>  	if (INTEL_GEN(dev_priv) >= 12) {
>  		enum transcoder trans;
>  
> -		for (trans = TRANSCODER_A; trans <= TRANSCODER_D; trans++) {
> +		for_each_cpu_transcoder_masked(dev_priv, trans, trans_mask) {
>  			enum intel_display_power_domain domain;
>  
>  			domain = POWER_DOMAIN_TRANSCODER(trans);
> -- 
> 2.24.1

-- 
Ville Syrjälä
Intel
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

  reply	other threads:[~2020-06-04 16:55 UTC|newest]

Thread overview: 41+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-06-03 21:15 [Intel-gfx] [PATCH v3 00/15] Remaining RKL patches Matt Roper
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 01/15] drm/i915/rkl: Set transcoder mask properly Matt Roper
2020-06-04 15:34   ` Ville Syrjälä
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 02/15] drm/i915/rkl: Program BW_BUDDY0 registers instead of BW_BUDDY1/2 Matt Roper
2020-06-03 22:34   ` Aditya Swarup
2020-06-03 23:12     ` Matt Roper
2020-06-04  1:18       ` Aditya Swarup
2020-06-04 17:01   ` Ville Syrjälä
2020-06-04 22:12     ` Matt Roper
2020-06-05 11:43       ` Ville Syrjälä
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 03/15] drm/i915/rkl: RKL has no MBUS_ABOX_CTL{1, 2} Matt Roper
2020-06-04 18:31   ` Ville Syrjälä
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 04/15] drm/i915/rkl: Handle new DPCLKA_CFGCR0 layout Matt Roper
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 05/15] drm/i915/rkl: Setup ports/phys Matt Roper
2020-06-04 17:09   ` Ville Syrjälä
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 06/15] drm/i915/rkl: provide port/phy mapping for vbt Matt Roper
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 07/15] drm/i915/rkl: Update TGP's pin mapping when paired with RKL Matt Roper
2020-06-04 18:29   ` Ville Syrjälä
2020-06-04 23:18     ` Matt Roper
2020-06-05 11:52       ` Ville Syrjälä
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 08/15] drm/i915/rkl: Add DDC pin mapping Matt Roper
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 09/15] drm/i915/rkl: Don't try to access transcoder D Matt Roper
2020-06-04 16:55   ` Ville Syrjälä [this message]
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 10/15] drm/i915/rkl: Don't try to read out DSI transcoders Matt Roper
2020-06-04 16:59   ` Ville Syrjälä
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 11/15] drm/i915/rkl: Handle comp master/slave relationships for PHYs Matt Roper
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 12/15] drm/i915/rkl: Add DPLL4 support Matt Roper
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 13/15] drm/i915/rkl: Handle HTI Matt Roper
2020-06-04 16:59   ` Ville Syrjälä
2020-06-04 22:55     ` Matt Roper
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 14/15] drm/i915/rkl: Disable PSR2 Matt Roper
2020-06-04 17:41   ` Rodrigo Vivi
2020-06-03 21:15 ` [Intel-gfx] [PATCH v3 15/15] drm/i915/rkl: Add initial workarounds Matt Roper
2020-06-03 22:02 ` [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Remaining RKL patches Patchwork
2020-06-03 22:03 ` [Intel-gfx] ✗ Fi.CI.SPARSE: " Patchwork
2020-06-03 22:23 ` [Intel-gfx] ✓ Fi.CI.BAT: success " Patchwork
2020-06-04  8:34 ` [Intel-gfx] ✓ Fi.CI.IGT: " Patchwork
2020-06-04 16:39   ` Matt Roper
2020-06-05 22:11     ` Chris Wilson
2020-06-06  3:21       ` Matt Roper
2020-06-06  9:01         ` Chris Wilson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200604165529.GW6112@intel.com \
    --to=ville.syrjala@linux.intel.com \
    --cc=intel-gfx@lists.freedesktop.org \
    --cc=matthew.d.roper@intel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.