From: Steen Hegelund <steen.hegelund@microchip.com> To: "David S. Miller" <davem@davemloft.net>, Jakub Kicinski <kuba@kernel.org>, Rob Herring <robh+dt@kernel.org>, Device Tree List <devicetree@vger.kernel.org> Cc: Steen Hegelund <steen.hegelund@microchip.com>, Andrew Lunn <andrew@lunn.ch>, Russell King <linux@armlinux.org.uk>, Lars Povlsen <lars.povlsen@microchip.com>, Bjarni Jonasson <bjarni.jonasson@microchip.com>, Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>, Alexandre Belloni <alexandre.belloni@bootlin.com>, Madalin Bucur <madalin.bucur@oss.nxp.com>, Nicolas Ferre <nicolas.ferre@microchip.com>, Mark Einon <mark.einon@gmail.com>, Masahiro Yamada <masahiroy@kernel.org>, Arnd Bergmann <arnd@arndb.de>, <netdev@vger.kernel.org>, <linux-kernel@vger.kernel.org>, <linux-arm-kernel@lists.infradead.org> Subject: [RFC PATCH v2 8/8] arm64: dts: sparx5: Add the Sparx5 switch node Date: Thu, 17 Dec 2020 08:51:34 +0100 [thread overview] Message-ID: <20201217075134.919699-9-steen.hegelund@microchip.com> (raw) In-Reply-To: <20201217075134.919699-1-steen.hegelund@microchip.com> This provides switchdev support for the Microship Sparx5 PCB134 and PCB135 reference boards. This commit depends on the following series currently on their way into the kernel: - Sparx5 SerDes Driver Link: https://lore.kernel.org/r/20201211090541.157926-1-steen.hegelund@microchip.com/ - Serial GPIO Controller Link: https://lore.kernel.org/r/20201113145151.68900-1-lars.povlsen@microchip.com/ Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com> Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com> --- arch/arm64/boot/dts/microchip/sparx5.dtsi | 60 ++ .../dts/microchip/sparx5_pcb134_board.dtsi | 424 ++++++++++-- .../dts/microchip/sparx5_pcb135_board.dtsi | 602 +++++++++++++++++- 3 files changed, 1026 insertions(+), 60 deletions(-) diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi index e480238489fa..085ab5a4fa50 100644 --- a/arch/arm64/boot/dts/microchip/sparx5.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi @@ -267,6 +267,21 @@ emmc_pins: emmc-pins { "GPIO_46", "GPIO_47"; function = "emmc"; }; + + miim1_pins: miim1-pins { + pins = "GPIO_56", "GPIO_57"; + function = "miim"; + }; + + miim2_pins: miim2-pins { + pins = "GPIO_58", "GPIO_59"; + function = "miim"; + }; + + miim3_pins: miim3-pins { + pins = "GPIO_52", "GPIO_53"; + function = "miim"; + }; }; sgpio0: gpio@61101036c { @@ -379,6 +394,44 @@ tmon0: tmon@610508110 { clocks = <&ahb_clk>; }; + mdio0: mdio@6110102b0 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102b0 0x24>; + }; + + mdio1: mdio@6110102d4 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim1_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102d4 0x24>; + }; + + mdio2: mdio@6110102f8 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim2_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102d4 0x24>; + }; + + mdio3: mdio@61101031c { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim3_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x1101031c 0x24>; + }; + serdes: serdes@10808000 { compatible = "microchip,sparx5-serdes"; #phy-cells = <1>; @@ -386,5 +439,12 @@ serdes: serdes@10808000 { reg = <0x6 0x10808000 0x5d0000>; }; + switch: switch@610004000 { + compatible = "microchip,sparx5-switch"; + reg = <0x6 0x10004000 0x800000>, + <0x6 0x11010000 0x1b00000>; + reg-names = "devices", "gcb"; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + }; }; }; diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi index 6820579448d0..efa35cbcef49 100644 --- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi @@ -7,30 +7,6 @@ #include "sparx5_pcb_common.dtsi" /{ - aliases { - i2c0 = &i2c0; - i2c100 = &i2c100; - i2c101 = &i2c101; - i2c102 = &i2c102; - i2c103 = &i2c103; - i2c104 = &i2c104; - i2c105 = &i2c105; - i2c106 = &i2c106; - i2c107 = &i2c107; - i2c108 = &i2c108; - i2c109 = &i2c109; - i2c110 = &i2c110; - i2c111 = &i2c111; - i2c112 = &i2c112; - i2c113 = &i2c113; - i2c114 = &i2c114; - i2c115 = &i2c115; - i2c116 = &i2c116; - i2c117 = &i2c117; - i2c118 = &i2c118; - i2c119 = &i2c119; - }; - gpio-restart { compatible = "gpio-restart"; gpios = <&gpio 37 GPIO_ACTIVE_LOW>; @@ -328,6 +304,11 @@ gpio@1 { }; }; +&sgpio2 { + status = "okay"; + microchip,sgpio-port-ranges = <0 0>, <11 31>; +}; + &gpio { i2cmux_pins_i: i2cmux-pins-i { pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19", @@ -415,9 +396,9 @@ i2c0_emux: i2c0-emux@0 { &i2c0_imux { pinctrl-names = - "i2c100", "i2c101", "i2c102", "i2c103", - "i2c104", "i2c105", "i2c106", "i2c107", - "i2c108", "i2c109", "i2c110", "i2c111", "idle"; + "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4", + "i2c_sfp5", "i2c_sfp6", "i2c_sfp7", "i2c_sfp8", + "i2c_sfp9", "i2c_sfp10", "i2c_sfp11", "i2c_sfp12", "idle"; pinctrl-0 = <&i2cmux_0>; pinctrl-1 = <&i2cmux_1>; pinctrl-2 = <&i2cmux_2>; @@ -431,62 +412,62 @@ &i2c0_imux { pinctrl-10 = <&i2cmux_10>; pinctrl-11 = <&i2cmux_11>; pinctrl-12 = <&i2cmux_pins_i>; - i2c100: i2c_sfp1 { + i2c_sfp1: i2c_sfp1 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c101: i2c_sfp2 { + i2c_sfp2: i2c_sfp2 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c102: i2c_sfp3 { + i2c_sfp3: i2c_sfp3 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c103: i2c_sfp4 { + i2c_sfp4: i2c_sfp4 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; - i2c104: i2c_sfp5 { + i2c_sfp5: i2c_sfp5 { reg = <0x4>; #address-cells = <1>; #size-cells = <0>; }; - i2c105: i2c_sfp6 { + i2c_sfp6: i2c_sfp6 { reg = <0x5>; #address-cells = <1>; #size-cells = <0>; }; - i2c106: i2c_sfp7 { + i2c_sfp7: i2c_sfp7 { reg = <0x6>; #address-cells = <1>; #size-cells = <0>; }; - i2c107: i2c_sfp8 { + i2c_sfp8: i2c_sfp8 { reg = <0x7>; #address-cells = <1>; #size-cells = <0>; }; - i2c108: i2c_sfp9 { + i2c_sfp9: i2c_sfp9 { reg = <0x8>; #address-cells = <1>; #size-cells = <0>; }; - i2c109: i2c_sfp10 { + i2c_sfp10: i2c_sfp10 { reg = <0x9>; #address-cells = <1>; #size-cells = <0>; }; - i2c110: i2c_sfp11 { + i2c_sfp11: i2c_sfp11 { reg = <0xa>; #address-cells = <1>; #size-cells = <0>; }; - i2c111: i2c_sfp12 { + i2c_sfp12: i2c_sfp12 { reg = <0xb>; #address-cells = <1>; #size-cells = <0>; @@ -499,44 +480,393 @@ &gpio 60 GPIO_ACTIVE_HIGH &gpio 61 GPIO_ACTIVE_HIGH &gpio 54 GPIO_ACTIVE_HIGH>; idle-state = <0x8>; - i2c112: i2c_sfp13 { + i2c_sfp13: i2c_sfp13 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c113: i2c_sfp14 { + i2c_sfp14: i2c_sfp14 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c114: i2c_sfp15 { + i2c_sfp15: i2c_sfp15 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c115: i2c_sfp16 { + i2c_sfp16: i2c_sfp16 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; - i2c116: i2c_sfp17 { + i2c_sfp17: i2c_sfp17 { reg = <0x4>; #address-cells = <1>; #size-cells = <0>; }; - i2c117: i2c_sfp18 { + i2c_sfp18: i2c_sfp18 { reg = <0x5>; #address-cells = <1>; #size-cells = <0>; }; - i2c118: i2c_sfp19 { + i2c_sfp19: i2c_sfp19 { reg = <0x6>; #address-cells = <1>; #size-cells = <0>; }; - i2c119: i2c_sfp20 { + i2c_sfp20: i2c_sfp20 { reg = <0x7>; #address-cells = <1>; #size-cells = <0>; }; }; + +&mdio3 { + status = "ok"; + phy64: ethernet-phy@64 { + reg = <28>; + }; +}; + +&axi { + sfp_eth12: sfp-eth12 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + tx-disable-gpios = <&sgpio_out2 11 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 11 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 11 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 12 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth13: sfp-eth13 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + tx-disable-gpios = <&sgpio_out2 12 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 12 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 12 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 13 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth14: sfp-eth14 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp3>; + tx-disable-gpios = <&sgpio_out2 13 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 13 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 13 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 14 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth15: sfp-eth15 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp4>; + tx-disable-gpios = <&sgpio_out2 14 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 14 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 14 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 15 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth48: sfp-eth48 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp5>; + tx-disable-gpios = <&sgpio_out2 15 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 15 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 15 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 16 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth49: sfp-eth49 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp6>; + tx-disable-gpios = <&sgpio_out2 16 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 16 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 16 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 17 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth50: sfp-eth50 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp7>; + tx-disable-gpios = <&sgpio_out2 17 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 17 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 17 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 18 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth51: sfp-eth51 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp8>; + tx-disable-gpios = <&sgpio_out2 18 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 18 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 18 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 19 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth52: sfp-eth52 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp9>; + tx-disable-gpios = <&sgpio_out2 19 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 19 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 19 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 20 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth53: sfp-eth53 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp10>; + tx-disable-gpios = <&sgpio_out2 20 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 20 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 20 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 21 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth54: sfp-eth54 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp11>; + tx-disable-gpios = <&sgpio_out2 21 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 21 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 21 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 22 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth55: sfp-eth55 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp12>; + tx-disable-gpios = <&sgpio_out2 22 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 22 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 22 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 23 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth56: sfp-eth56 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp13>; + tx-disable-gpios = <&sgpio_out2 23 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 23 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 23 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 24 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth57: sfp-eth57 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp14>; + tx-disable-gpios = <&sgpio_out2 24 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 24 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 24 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 25 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth58: sfp-eth58 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp15>; + tx-disable-gpios = <&sgpio_out2 25 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 25 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 25 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 26 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth59: sfp-eth59 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp16>; + tx-disable-gpios = <&sgpio_out2 26 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 26 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 26 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 27 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth60: sfp-eth60 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp17>; + tx-disable-gpios = <&sgpio_out2 27 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 27 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 27 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth61: sfp-eth61 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp18>; + tx-disable-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth62: sfp-eth62 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp19>; + tx-disable-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth63: sfp-eth63 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp20>; + tx-disable-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>; + }; +}; + +&switch { + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + /* 10G SFPs */ + port12: port@12 { + reg = <12>; + max-speed = <10000>; + phys = <&serdes 13>; + sfp = <&sfp_eth12>; + sd_sgpio = <301>; + managed = "in-band-status"; + }; + port13: port@13 { + reg = <13>; + /* Example: CU SFP, 1G speed */ + max-speed = <10000>; + phys = <&serdes 14>; + sfp = <&sfp_eth13>; + sd_sgpio = <305>; + managed = "in-band-status"; + }; + port14: port@14 { + reg = <14>; + max-speed = <10000>; + phys = <&serdes 15>; + sfp = <&sfp_eth14>; + sd_sgpio = <309>; + managed = "in-band-status"; + }; + port15: port@15 { + reg = <15>; + max-speed = <10000>; + phys = <&serdes 16>; + sfp = <&sfp_eth15>; + sd_sgpio = <313>; + managed = "in-band-status"; + }; + port48: port@48 { + reg = <48>; + max-speed = <10000>; + phys = <&serdes 17>; + sfp = <&sfp_eth48>; + sd_sgpio = <317>; + managed = "in-band-status"; + }; + port49: port@49 { + reg = <49>; + max-speed = <10000>; + phys = <&serdes 18>; + sfp = <&sfp_eth49>; + sd_sgpio = <321>; + managed = "in-band-status"; + }; + port50: port@50 { + reg = <50>; + max-speed = <10000>; + phys = <&serdes 19>; + sfp = <&sfp_eth50>; + sd_sgpio = <325>; + managed = "in-band-status"; + }; + port51: port@51 { + reg = <51>; + max-speed = <10000>; + phys = <&serdes 20>; + sfp = <&sfp_eth51>; + sd_sgpio = <329>; + managed = "in-band-status"; + }; + port52: port@52 { + reg = <52>; + max-speed = <10000>; + phys = <&serdes 21>; + sfp = <&sfp_eth52>; + sd_sgpio = <333>; + managed = "in-band-status"; + }; + port53: port@53 { + reg = <53>; + max-speed = <10000>; + phys = <&serdes 22>; + sfp = <&sfp_eth53>; + sd_sgpio = <337>; + managed = "in-band-status"; + }; + port54: port@54 { + reg = <54>; + max-speed = <10000>; + phys = <&serdes 23>; + sfp = <&sfp_eth54>; + sd_sgpio = <341>; + managed = "in-band-status"; + }; + port55: port@55 { + reg = <55>; + max-speed = <10000>; + phys = <&serdes 24>; + sfp = <&sfp_eth55>; + sd_sgpio = <345>; + managed = "in-band-status"; + }; + /* 25G SFPs */ + port56: port@56 { + reg = <56>; + max-speed = <10000>; + phys = <&serdes 25>; + sfp = <&sfp_eth56>; + sd_sgpio = <349>; + managed = "in-band-status"; + }; + port57: port@57 { + reg = <57>; + max-speed = <10000>; + phys = <&serdes 26>; + sfp = <&sfp_eth57>; + sd_sgpio = <353>; + managed = "in-band-status"; + }; + port58: port@58 { + reg = <58>; + max-speed = <10000>; + phys = <&serdes 27>; + sfp = <&sfp_eth58>; + sd_sgpio = <357>; + managed = "in-band-status"; + }; + port59: port@59 { + reg = <59>; + max-speed = <10000>; + phys = <&serdes 28>; + sfp = <&sfp_eth59>; + sd_sgpio = <361>; + managed = "in-band-status"; + }; + port60: port@60 { + reg = <60>; + max-speed = <10000>; + phys = <&serdes 29>; + sfp = <&sfp_eth60>; + sd_sgpio = <365>; + managed = "in-band-status"; + }; + port61: port@61 { + reg = <61>; + max-speed = <10000>; + phys = <&serdes 30>; + sfp = <&sfp_eth61>; + sd_sgpio = <369>; + managed = "in-band-status"; + }; + port62: port@62 { + reg = <62>; + max-speed = <10000>; + phys = <&serdes 31>; + sfp = <&sfp_eth62>; + sd_sgpio = <373>; + managed = "in-band-status"; + }; + port63: port@63 { + reg = <63>; + max-speed = <10000>; + phys = <&serdes 32>; + sfp = <&sfp_eth63>; + sd_sgpio = <377>; + managed = "in-band-status"; + }; + /* Finally the Management interface */ + port64: port@64 { + reg = <64>; + max-speed = <1000>; + phys = <&serdes 0>; + phy-handle = <&phy64>; + phy-mode = "sgmii"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi index e28c6dd16377..69e136c7bb9c 100644 --- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi @@ -7,14 +7,6 @@ #include "sparx5_pcb_common.dtsi" /{ - aliases { - i2c0 = &i2c0; - i2c152 = &i2c152; - i2c153 = &i2c153; - i2c154 = &i2c154; - i2c155 = &i2c155; - }; - gpio-restart { compatible = "gpio-restart"; gpios = <&gpio 37 GPIO_ACTIVE_LOW>; @@ -138,6 +130,11 @@ gpio@1 { }; }; +&sgpio2 { + status = "okay"; + microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>; +}; + &axi { i2c0_imux: i2c0-imux@0 { compatible = "i2c-mux-pinctrl"; @@ -149,31 +146,610 @@ i2c0_imux: i2c0-imux@0 { &i2c0_imux { pinctrl-names = - "i2c152", "i2c153", "i2c154", "i2c155", + "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4", "idle"; pinctrl-0 = <&i2cmux_s29>; pinctrl-1 = <&i2cmux_s30>; pinctrl-2 = <&i2cmux_s31>; pinctrl-3 = <&i2cmux_s32>; pinctrl-4 = <&i2cmux_pins_i>; - i2c152: i2c_sfp1 { + i2c_sfp1: i2c_sfp1 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c153: i2c_sfp2 { + i2c_sfp2: i2c_sfp2 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c154: i2c_sfp3 { + i2c_sfp3: i2c_sfp3 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c155: i2c_sfp4 { + i2c_sfp4: i2c_sfp4 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; }; + +&axi { + sfp_eth60: sfp-eth60 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + tx-disable-gpios = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth61: sfp-eth61 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + tx-disable-gpios = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth62: sfp-eth62 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp3>; + tx-disable-gpios = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth63: sfp-eth63 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp4>; + tx-disable-gpios = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>; + }; +}; + +&mdio0 { + status = "ok"; + phy0: ethernet-phy@0 { + reg = <0>; + }; + phy1: ethernet-phy@1 { + reg = <1>; + }; + phy2: ethernet-phy@2 { + reg = <2>; + }; + phy3: ethernet-phy@3 { + reg = <3>; + }; + phy4: ethernet-phy@4 { + reg = <4>; + }; + phy5: ethernet-phy@5 { + reg = <5>; + }; + phy6: ethernet-phy@6 { + reg = <6>; + }; + phy7: ethernet-phy@7 { + reg = <7>; + }; + phy8: ethernet-phy@8 { + reg = <8>; + }; + phy9: ethernet-phy@9 { + reg = <9>; + }; + phy10: ethernet-phy@10 { + reg = <10>; + }; + phy11: ethernet-phy@11 { + reg = <11>; + }; + phy12: ethernet-phy@12 { + reg = <12>; + }; + phy13: ethernet-phy@13 { + reg = <13>; + }; + phy14: ethernet-phy@14 { + reg = <14>; + }; + phy15: ethernet-phy@15 { + reg = <15>; + }; + phy16: ethernet-phy@16 { + reg = <16>; + }; + phy17: ethernet-phy@17 { + reg = <17>; + }; + phy18: ethernet-phy@18 { + reg = <18>; + }; + phy19: ethernet-phy@19 { + reg = <19>; + }; + phy20: ethernet-phy@20 { + reg = <20>; + }; + phy21: ethernet-phy@21 { + reg = <21>; + }; + phy22: ethernet-phy@22 { + reg = <22>; + }; + phy23: ethernet-phy@23 { + reg = <23>; + }; +}; + +&mdio1 { + status = "ok"; + phy24: ethernet-phy@24 { + reg = <0>; + }; + phy25: ethernet-phy@25 { + reg = <1>; + }; + phy26: ethernet-phy@26 { + reg = <2>; + }; + phy27: ethernet-phy@27 { + reg = <3>; + }; + phy28: ethernet-phy@28 { + reg = <4>; + }; + phy29: ethernet-phy@29 { + reg = <5>; + }; + phy30: ethernet-phy@30 { + reg = <6>; + }; + phy31: ethernet-phy@31 { + reg = <7>; + }; + phy32: ethernet-phy@32 { + reg = <8>; + }; + phy33: ethernet-phy@33 { + reg = <9>; + }; + phy34: ethernet-phy@34 { + reg = <10>; + }; + phy35: ethernet-phy@35 { + reg = <11>; + }; + phy36: ethernet-phy@36 { + reg = <12>; + }; + phy37: ethernet-phy@37 { + reg = <13>; + }; + phy38: ethernet-phy@38 { + reg = <14>; + }; + phy39: ethernet-phy@39 { + reg = <15>; + }; + phy40: ethernet-phy@40 { + reg = <16>; + }; + phy41: ethernet-phy@41 { + reg = <17>; + }; + phy42: ethernet-phy@42 { + reg = <18>; + }; + phy43: ethernet-phy@43 { + reg = <19>; + }; + phy44: ethernet-phy@44 { + reg = <20>; + }; + phy45: ethernet-phy@45 { + reg = <21>; + }; + phy46: ethernet-phy@46 { + reg = <22>; + }; + phy47: ethernet-phy@47 { + reg = <23>; + }; +}; + +&mdio3 { + status = "ok"; + phy64: ethernet-phy@64 { + reg = <28>; + }; +}; + +&switch { + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port0: port@0 { + reg = <0>; + max-speed = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy0>; + phy-mode = "qsgmii"; + }; + port1: port@1 { + reg = <1>; + max-speed = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy1>; + phy-mode = "qsgmii"; + }; + port2: port@2 { + reg = <2>; + max-speed = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy2>; + phy-mode = "qsgmii"; + }; + port3: port@3 { + reg = <3>; + max-speed = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy3>; + phy-mode = "qsgmii"; + }; + port4: port@4 { + reg = <4>; + max-speed = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy4>; + phy-mode = "qsgmii"; + }; + port5: port@5 { + reg = <5>; + max-speed = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy5>; + phy-mode = "qsgmii"; + }; + port6: port@6 { + reg = <6>; + max-speed = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy6>; + phy-mode = "qsgmii"; + }; + port7: port@7 { + reg = <7>; + max-speed = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy7>; + phy-mode = "qsgmii"; + }; + port8: port@8 { + reg = <8>; + max-speed = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy8>; + phy-mode = "qsgmii"; + }; + port9: port@9 { + reg = <9>; + max-speed = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy9>; + phy-mode = "qsgmii"; + }; + port10: port@10 { + reg = <10>; + max-speed = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy10>; + phy-mode = "qsgmii"; + }; + port11: port@11 { + reg = <11>; + max-speed = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy11>; + phy-mode = "qsgmii"; + }; + port12: port@12 { + reg = <12>; + max-speed = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy12>; + phy-mode = "qsgmii"; + }; + port13: port@13 { + reg = <13>; + max-speed = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy13>; + phy-mode = "qsgmii"; + }; + port14: port@14 { + reg = <14>; + max-speed = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy14>; + phy-mode = "qsgmii"; + }; + port15: port@15 { + reg = <15>; + max-speed = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy15>; + phy-mode = "qsgmii"; + }; + port16: port@16 { + reg = <16>; + max-speed = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy16>; + phy-mode = "qsgmii"; + }; + port17: port@17 { + reg = <17>; + max-speed = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy17>; + phy-mode = "qsgmii"; + }; + port18: port@18 { + reg = <18>; + max-speed = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy18>; + phy-mode = "qsgmii"; + }; + port19: port@19 { + reg = <19>; + max-speed = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy19>; + phy-mode = "qsgmii"; + }; + port20: port@20 { + reg = <20>; + max-speed = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy20>; + phy-mode = "qsgmii"; + }; + port21: port@21 { + reg = <21>; + max-speed = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy21>; + phy-mode = "qsgmii"; + }; + port22: port@22 { + reg = <22>; + max-speed = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy22>; + phy-mode = "qsgmii"; + }; + port23: port@23 { + reg = <23>; + max-speed = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy23>; + phy-mode = "qsgmii"; + }; + port24: port@24 { + reg = <24>; + max-speed = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy24>; + phy-mode = "qsgmii"; + }; + port25: port@25 { + reg = <25>; + max-speed = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy25>; + phy-mode = "qsgmii"; + }; + port26: port@26 { + reg = <26>; + max-speed = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy26>; + phy-mode = "qsgmii"; + }; + port27: port@27 { + reg = <27>; + max-speed = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy27>; + phy-mode = "qsgmii"; + }; + port28: port@28 { + reg = <28>; + max-speed = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy28>; + phy-mode = "qsgmii"; + }; + port29: port@29 { + reg = <29>; + max-speed = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy29>; + phy-mode = "qsgmii"; + }; + port30: port@30 { + reg = <30>; + max-speed = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy30>; + phy-mode = "qsgmii"; + }; + port31: port@31 { + reg = <31>; + max-speed = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy31>; + phy-mode = "qsgmii"; + }; + port32: port@32 { + reg = <32>; + max-speed = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy32>; + phy-mode = "qsgmii"; + }; + port33: port@33 { + reg = <33>; + max-speed = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy33>; + phy-mode = "qsgmii"; + }; + port34: port@34 { + reg = <34>; + max-speed = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy34>; + phy-mode = "qsgmii"; + }; + port35: port@35 { + reg = <35>; + max-speed = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy35>; + phy-mode = "qsgmii"; + }; + port36: port@36 { + reg = <36>; + max-speed = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy36>; + phy-mode = "qsgmii"; + }; + port37: port@37 { + reg = <37>; + max-speed = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy37>; + phy-mode = "qsgmii"; + }; + port38: port@38 { + reg = <38>; + max-speed = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy38>; + phy-mode = "qsgmii"; + }; + port39: port@39 { + reg = <39>; + max-speed = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy39>; + phy-mode = "qsgmii"; + }; + port40: port@40 { + reg = <40>; + max-speed = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy40>; + phy-mode = "qsgmii"; + }; + port41: port@41 { + reg = <41>; + max-speed = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy41>; + phy-mode = "qsgmii"; + }; + port42: port@42 { + reg = <42>; + max-speed = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy42>; + phy-mode = "qsgmii"; + }; + port43: port@43 { + reg = <43>; + max-speed = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy43>; + phy-mode = "qsgmii"; + }; + port44: port@44 { + reg = <44>; + max-speed = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy44>; + phy-mode = "qsgmii"; + }; + port45: port@45 { + reg = <45>; + max-speed = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy45>; + phy-mode = "qsgmii"; + }; + port46: port@46 { + reg = <46>; + max-speed = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy46>; + phy-mode = "qsgmii"; + }; + port47: port@47 { + reg = <47>; + max-speed = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy47>; + phy-mode = "qsgmii"; + }; + /* Then the 25G interfaces */ + port60: port@60 { + reg = <60>; + max-speed = <25000>; + phys = <&serdes 29>; + sfp = <&sfp_eth60>; + managed = "in-band-status"; + }; + port61: port@61 { + reg = <61>; + max-speed = <25000>; + phys = <&serdes 30>; + sfp = <&sfp_eth61>; + managed = "in-band-status"; + }; + port62: port@62 { + reg = <62>; + max-speed = <25000>; + phys = <&serdes 31>; + sfp = <&sfp_eth62>; + managed = "in-band-status"; + }; + port63: port@63 { + reg = <63>; + max-speed = <25000>; + phys = <&serdes 32>; + sfp = <&sfp_eth63>; + managed = "in-band-status"; + }; + /* Finally the Management interface */ + port64: port@64 { + reg = <64>; + max-speed = <1000>; + phys = <&serdes 0>; + phy-handle = <&phy64>; + phy-mode = "sgmii"; + }; + }; +}; -- 2.29.2
WARNING: multiple messages have this Message-ID (diff)
From: Steen Hegelund <steen.hegelund@microchip.com> To: "David S. Miller" <davem@davemloft.net>, Jakub Kicinski <kuba@kernel.org>, Rob Herring <robh+dt@kernel.org>, Device Tree List <devicetree@vger.kernel.org> Cc: Andrew Lunn <andrew@lunn.ch>, Alexandre Belloni <alexandre.belloni@bootlin.com>, linux-kernel@vger.kernel.org, Arnd Bergmann <arnd@arndb.de>, Bjarni Jonasson <bjarni.jonasson@microchip.com>, Madalin Bucur <madalin.bucur@oss.nxp.com>, netdev@vger.kernel.org, Steen Hegelund <steen.hegelund@microchip.com>, Russell King <linux@armlinux.org.uk>, Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>, linux-arm-kernel@lists.infradead.org, Mark Einon <mark.einon@gmail.com>, Masahiro Yamada <masahiroy@kernel.org>, Lars Povlsen <lars.povlsen@microchip.com> Subject: [RFC PATCH v2 8/8] arm64: dts: sparx5: Add the Sparx5 switch node Date: Thu, 17 Dec 2020 08:51:34 +0100 [thread overview] Message-ID: <20201217075134.919699-9-steen.hegelund@microchip.com> (raw) In-Reply-To: <20201217075134.919699-1-steen.hegelund@microchip.com> This provides switchdev support for the Microship Sparx5 PCB134 and PCB135 reference boards. This commit depends on the following series currently on their way into the kernel: - Sparx5 SerDes Driver Link: https://lore.kernel.org/r/20201211090541.157926-1-steen.hegelund@microchip.com/ - Serial GPIO Controller Link: https://lore.kernel.org/r/20201113145151.68900-1-lars.povlsen@microchip.com/ Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com> Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com> --- arch/arm64/boot/dts/microchip/sparx5.dtsi | 60 ++ .../dts/microchip/sparx5_pcb134_board.dtsi | 424 ++++++++++-- .../dts/microchip/sparx5_pcb135_board.dtsi | 602 +++++++++++++++++- 3 files changed, 1026 insertions(+), 60 deletions(-) diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi index e480238489fa..085ab5a4fa50 100644 --- a/arch/arm64/boot/dts/microchip/sparx5.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi @@ -267,6 +267,21 @@ emmc_pins: emmc-pins { "GPIO_46", "GPIO_47"; function = "emmc"; }; + + miim1_pins: miim1-pins { + pins = "GPIO_56", "GPIO_57"; + function = "miim"; + }; + + miim2_pins: miim2-pins { + pins = "GPIO_58", "GPIO_59"; + function = "miim"; + }; + + miim3_pins: miim3-pins { + pins = "GPIO_52", "GPIO_53"; + function = "miim"; + }; }; sgpio0: gpio@61101036c { @@ -379,6 +394,44 @@ tmon0: tmon@610508110 { clocks = <&ahb_clk>; }; + mdio0: mdio@6110102b0 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102b0 0x24>; + }; + + mdio1: mdio@6110102d4 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim1_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102d4 0x24>; + }; + + mdio2: mdio@6110102f8 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim2_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102d4 0x24>; + }; + + mdio3: mdio@61101031c { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim3_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x1101031c 0x24>; + }; + serdes: serdes@10808000 { compatible = "microchip,sparx5-serdes"; #phy-cells = <1>; @@ -386,5 +439,12 @@ serdes: serdes@10808000 { reg = <0x6 0x10808000 0x5d0000>; }; + switch: switch@610004000 { + compatible = "microchip,sparx5-switch"; + reg = <0x6 0x10004000 0x800000>, + <0x6 0x11010000 0x1b00000>; + reg-names = "devices", "gcb"; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + }; }; }; diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi index 6820579448d0..efa35cbcef49 100644 --- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi @@ -7,30 +7,6 @@ #include "sparx5_pcb_common.dtsi" /{ - aliases { - i2c0 = &i2c0; - i2c100 = &i2c100; - i2c101 = &i2c101; - i2c102 = &i2c102; - i2c103 = &i2c103; - i2c104 = &i2c104; - i2c105 = &i2c105; - i2c106 = &i2c106; - i2c107 = &i2c107; - i2c108 = &i2c108; - i2c109 = &i2c109; - i2c110 = &i2c110; - i2c111 = &i2c111; - i2c112 = &i2c112; - i2c113 = &i2c113; - i2c114 = &i2c114; - i2c115 = &i2c115; - i2c116 = &i2c116; - i2c117 = &i2c117; - i2c118 = &i2c118; - i2c119 = &i2c119; - }; - gpio-restart { compatible = "gpio-restart"; gpios = <&gpio 37 GPIO_ACTIVE_LOW>; @@ -328,6 +304,11 @@ gpio@1 { }; }; +&sgpio2 { + status = "okay"; + microchip,sgpio-port-ranges = <0 0>, <11 31>; +}; + &gpio { i2cmux_pins_i: i2cmux-pins-i { pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19", @@ -415,9 +396,9 @@ i2c0_emux: i2c0-emux@0 { &i2c0_imux { pinctrl-names = - "i2c100", "i2c101", "i2c102", "i2c103", - "i2c104", "i2c105", "i2c106", "i2c107", - "i2c108", "i2c109", "i2c110", "i2c111", "idle"; + "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4", + "i2c_sfp5", "i2c_sfp6", "i2c_sfp7", "i2c_sfp8", + "i2c_sfp9", "i2c_sfp10", "i2c_sfp11", "i2c_sfp12", "idle"; pinctrl-0 = <&i2cmux_0>; pinctrl-1 = <&i2cmux_1>; pinctrl-2 = <&i2cmux_2>; @@ -431,62 +412,62 @@ &i2c0_imux { pinctrl-10 = <&i2cmux_10>; pinctrl-11 = <&i2cmux_11>; pinctrl-12 = <&i2cmux_pins_i>; - i2c100: i2c_sfp1 { + i2c_sfp1: i2c_sfp1 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c101: i2c_sfp2 { + i2c_sfp2: i2c_sfp2 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c102: i2c_sfp3 { + i2c_sfp3: i2c_sfp3 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c103: i2c_sfp4 { + i2c_sfp4: i2c_sfp4 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; - i2c104: i2c_sfp5 { + i2c_sfp5: i2c_sfp5 { reg = <0x4>; #address-cells = <1>; #size-cells = <0>; }; - i2c105: i2c_sfp6 { + i2c_sfp6: i2c_sfp6 { reg = <0x5>; #address-cells = <1>; #size-cells = <0>; }; - i2c106: i2c_sfp7 { + i2c_sfp7: i2c_sfp7 { reg = <0x6>; #address-cells = <1>; #size-cells = <0>; }; - i2c107: i2c_sfp8 { + i2c_sfp8: i2c_sfp8 { reg = <0x7>; #address-cells = <1>; #size-cells = <0>; }; - i2c108: i2c_sfp9 { + i2c_sfp9: i2c_sfp9 { reg = <0x8>; #address-cells = <1>; #size-cells = <0>; }; - i2c109: i2c_sfp10 { + i2c_sfp10: i2c_sfp10 { reg = <0x9>; #address-cells = <1>; #size-cells = <0>; }; - i2c110: i2c_sfp11 { + i2c_sfp11: i2c_sfp11 { reg = <0xa>; #address-cells = <1>; #size-cells = <0>; }; - i2c111: i2c_sfp12 { + i2c_sfp12: i2c_sfp12 { reg = <0xb>; #address-cells = <1>; #size-cells = <0>; @@ -499,44 +480,393 @@ &gpio 60 GPIO_ACTIVE_HIGH &gpio 61 GPIO_ACTIVE_HIGH &gpio 54 GPIO_ACTIVE_HIGH>; idle-state = <0x8>; - i2c112: i2c_sfp13 { + i2c_sfp13: i2c_sfp13 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c113: i2c_sfp14 { + i2c_sfp14: i2c_sfp14 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c114: i2c_sfp15 { + i2c_sfp15: i2c_sfp15 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c115: i2c_sfp16 { + i2c_sfp16: i2c_sfp16 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; - i2c116: i2c_sfp17 { + i2c_sfp17: i2c_sfp17 { reg = <0x4>; #address-cells = <1>; #size-cells = <0>; }; - i2c117: i2c_sfp18 { + i2c_sfp18: i2c_sfp18 { reg = <0x5>; #address-cells = <1>; #size-cells = <0>; }; - i2c118: i2c_sfp19 { + i2c_sfp19: i2c_sfp19 { reg = <0x6>; #address-cells = <1>; #size-cells = <0>; }; - i2c119: i2c_sfp20 { + i2c_sfp20: i2c_sfp20 { reg = <0x7>; #address-cells = <1>; #size-cells = <0>; }; }; + +&mdio3 { + status = "ok"; + phy64: ethernet-phy@64 { + reg = <28>; + }; +}; + +&axi { + sfp_eth12: sfp-eth12 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + tx-disable-gpios = <&sgpio_out2 11 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 11 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 11 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 12 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth13: sfp-eth13 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + tx-disable-gpios = <&sgpio_out2 12 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 12 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 12 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 13 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth14: sfp-eth14 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp3>; + tx-disable-gpios = <&sgpio_out2 13 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 13 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 13 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 14 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth15: sfp-eth15 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp4>; + tx-disable-gpios = <&sgpio_out2 14 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 14 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 14 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 15 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth48: sfp-eth48 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp5>; + tx-disable-gpios = <&sgpio_out2 15 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 15 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 15 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 16 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth49: sfp-eth49 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp6>; + tx-disable-gpios = <&sgpio_out2 16 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 16 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 16 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 17 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth50: sfp-eth50 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp7>; + tx-disable-gpios = <&sgpio_out2 17 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 17 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 17 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 18 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth51: sfp-eth51 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp8>; + tx-disable-gpios = <&sgpio_out2 18 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 18 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 18 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 19 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth52: sfp-eth52 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp9>; + tx-disable-gpios = <&sgpio_out2 19 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 19 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 19 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 20 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth53: sfp-eth53 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp10>; + tx-disable-gpios = <&sgpio_out2 20 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 20 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 20 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 21 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth54: sfp-eth54 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp11>; + tx-disable-gpios = <&sgpio_out2 21 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 21 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 21 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 22 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth55: sfp-eth55 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp12>; + tx-disable-gpios = <&sgpio_out2 22 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 22 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 22 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 23 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth56: sfp-eth56 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp13>; + tx-disable-gpios = <&sgpio_out2 23 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 23 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 23 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 24 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth57: sfp-eth57 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp14>; + tx-disable-gpios = <&sgpio_out2 24 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 24 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 24 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 25 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth58: sfp-eth58 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp15>; + tx-disable-gpios = <&sgpio_out2 25 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 25 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 25 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 26 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth59: sfp-eth59 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp16>; + tx-disable-gpios = <&sgpio_out2 26 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 26 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 26 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 27 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth60: sfp-eth60 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp17>; + tx-disable-gpios = <&sgpio_out2 27 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 27 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 27 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth61: sfp-eth61 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp18>; + tx-disable-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth62: sfp-eth62 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp19>; + tx-disable-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth63: sfp-eth63 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp20>; + tx-disable-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>; + }; +}; + +&switch { + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + /* 10G SFPs */ + port12: port@12 { + reg = <12>; + max-speed = <10000>; + phys = <&serdes 13>; + sfp = <&sfp_eth12>; + sd_sgpio = <301>; + managed = "in-band-status"; + }; + port13: port@13 { + reg = <13>; + /* Example: CU SFP, 1G speed */ + max-speed = <10000>; + phys = <&serdes 14>; + sfp = <&sfp_eth13>; + sd_sgpio = <305>; + managed = "in-band-status"; + }; + port14: port@14 { + reg = <14>; + max-speed = <10000>; + phys = <&serdes 15>; + sfp = <&sfp_eth14>; + sd_sgpio = <309>; + managed = "in-band-status"; + }; + port15: port@15 { + reg = <15>; + max-speed = <10000>; + phys = <&serdes 16>; + sfp = <&sfp_eth15>; + sd_sgpio = <313>; + managed = "in-band-status"; + }; + port48: port@48 { + reg = <48>; + max-speed = <10000>; + phys = <&serdes 17>; + sfp = <&sfp_eth48>; + sd_sgpio = <317>; + managed = "in-band-status"; + }; + port49: port@49 { + reg = <49>; + max-speed = <10000>; + phys = <&serdes 18>; + sfp = <&sfp_eth49>; + sd_sgpio = <321>; + managed = "in-band-status"; + }; + port50: port@50 { + reg = <50>; + max-speed = <10000>; + phys = <&serdes 19>; + sfp = <&sfp_eth50>; + sd_sgpio = <325>; + managed = "in-band-status"; + }; + port51: port@51 { + reg = <51>; + max-speed = <10000>; + phys = <&serdes 20>; + sfp = <&sfp_eth51>; + sd_sgpio = <329>; + managed = "in-band-status"; + }; + port52: port@52 { + reg = <52>; + max-speed = <10000>; + phys = <&serdes 21>; + sfp = <&sfp_eth52>; + sd_sgpio = <333>; + managed = "in-band-status"; + }; + port53: port@53 { + reg = <53>; + max-speed = <10000>; + phys = <&serdes 22>; + sfp = <&sfp_eth53>; + sd_sgpio = <337>; + managed = "in-band-status"; + }; + port54: port@54 { + reg = <54>; + max-speed = <10000>; + phys = <&serdes 23>; + sfp = <&sfp_eth54>; + sd_sgpio = <341>; + managed = "in-band-status"; + }; + port55: port@55 { + reg = <55>; + max-speed = <10000>; + phys = <&serdes 24>; + sfp = <&sfp_eth55>; + sd_sgpio = <345>; + managed = "in-band-status"; + }; + /* 25G SFPs */ + port56: port@56 { + reg = <56>; + max-speed = <10000>; + phys = <&serdes 25>; + sfp = <&sfp_eth56>; + sd_sgpio = <349>; + managed = "in-band-status"; + }; + port57: port@57 { + reg = <57>; + max-speed = <10000>; + phys = <&serdes 26>; + sfp = <&sfp_eth57>; + sd_sgpio = <353>; + managed = "in-band-status"; + }; + port58: port@58 { + reg = <58>; + max-speed = <10000>; + phys = <&serdes 27>; + sfp = <&sfp_eth58>; + sd_sgpio = <357>; + managed = "in-band-status"; + }; + port59: port@59 { + reg = <59>; + max-speed = <10000>; + phys = <&serdes 28>; + sfp = <&sfp_eth59>; + sd_sgpio = <361>; + managed = "in-band-status"; + }; + port60: port@60 { + reg = <60>; + max-speed = <10000>; + phys = <&serdes 29>; + sfp = <&sfp_eth60>; + sd_sgpio = <365>; + managed = "in-band-status"; + }; + port61: port@61 { + reg = <61>; + max-speed = <10000>; + phys = <&serdes 30>; + sfp = <&sfp_eth61>; + sd_sgpio = <369>; + managed = "in-band-status"; + }; + port62: port@62 { + reg = <62>; + max-speed = <10000>; + phys = <&serdes 31>; + sfp = <&sfp_eth62>; + sd_sgpio = <373>; + managed = "in-band-status"; + }; + port63: port@63 { + reg = <63>; + max-speed = <10000>; + phys = <&serdes 32>; + sfp = <&sfp_eth63>; + sd_sgpio = <377>; + managed = "in-band-status"; + }; + /* Finally the Management interface */ + port64: port@64 { + reg = <64>; + max-speed = <1000>; + phys = <&serdes 0>; + phy-handle = <&phy64>; + phy-mode = "sgmii"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi index e28c6dd16377..69e136c7bb9c 100644 --- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi @@ -7,14 +7,6 @@ #include "sparx5_pcb_common.dtsi" /{ - aliases { - i2c0 = &i2c0; - i2c152 = &i2c152; - i2c153 = &i2c153; - i2c154 = &i2c154; - i2c155 = &i2c155; - }; - gpio-restart { compatible = "gpio-restart"; gpios = <&gpio 37 GPIO_ACTIVE_LOW>; @@ -138,6 +130,11 @@ gpio@1 { }; }; +&sgpio2 { + status = "okay"; + microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>; +}; + &axi { i2c0_imux: i2c0-imux@0 { compatible = "i2c-mux-pinctrl"; @@ -149,31 +146,610 @@ i2c0_imux: i2c0-imux@0 { &i2c0_imux { pinctrl-names = - "i2c152", "i2c153", "i2c154", "i2c155", + "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4", "idle"; pinctrl-0 = <&i2cmux_s29>; pinctrl-1 = <&i2cmux_s30>; pinctrl-2 = <&i2cmux_s31>; pinctrl-3 = <&i2cmux_s32>; pinctrl-4 = <&i2cmux_pins_i>; - i2c152: i2c_sfp1 { + i2c_sfp1: i2c_sfp1 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c153: i2c_sfp2 { + i2c_sfp2: i2c_sfp2 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c154: i2c_sfp3 { + i2c_sfp3: i2c_sfp3 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c155: i2c_sfp4 { + i2c_sfp4: i2c_sfp4 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; }; + +&axi { + sfp_eth60: sfp-eth60 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + tx-disable-gpios = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth61: sfp-eth61 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + tx-disable-gpios = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth62: sfp-eth62 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp3>; + tx-disable-gpios = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth63: sfp-eth63 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp4>; + tx-disable-gpios = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>; + }; +}; + +&mdio0 { + status = "ok"; + phy0: ethernet-phy@0 { + reg = <0>; + }; + phy1: ethernet-phy@1 { + reg = <1>; + }; + phy2: ethernet-phy@2 { + reg = <2>; + }; + phy3: ethernet-phy@3 { + reg = <3>; + }; + phy4: ethernet-phy@4 { + reg = <4>; + }; + phy5: ethernet-phy@5 { + reg = <5>; + }; + phy6: ethernet-phy@6 { + reg = <6>; + }; + phy7: ethernet-phy@7 { + reg = <7>; + }; + phy8: ethernet-phy@8 { + reg = <8>; + }; + phy9: ethernet-phy@9 { + reg = <9>; + }; + phy10: ethernet-phy@10 { + reg = <10>; + }; + phy11: ethernet-phy@11 { + reg = <11>; + }; + phy12: ethernet-phy@12 { + reg = <12>; + }; + phy13: ethernet-phy@13 { + reg = <13>; + }; + phy14: ethernet-phy@14 { + reg = <14>; + }; + phy15: ethernet-phy@15 { + reg = <15>; + }; + phy16: ethernet-phy@16 { + reg = <16>; + }; + phy17: ethernet-phy@17 { + reg = <17>; + }; + phy18: ethernet-phy@18 { + reg = <18>; + }; + phy19: ethernet-phy@19 { + reg = <19>; + }; + phy20: ethernet-phy@20 { + reg = <20>; + }; + phy21: ethernet-phy@21 { + reg = <21>; + }; + phy22: ethernet-phy@22 { + reg = <22>; + }; + phy23: ethernet-phy@23 { + reg = <23>; + }; +}; + +&mdio1 { + status = "ok"; + phy24: ethernet-phy@24 { + reg = <0>; + }; + phy25: ethernet-phy@25 { + reg = <1>; + }; + phy26: ethernet-phy@26 { + reg = <2>; + }; + phy27: ethernet-phy@27 { + reg = <3>; + }; + phy28: ethernet-phy@28 { + reg = <4>; + }; + phy29: ethernet-phy@29 { + reg = <5>; + }; + phy30: ethernet-phy@30 { + reg = <6>; + }; + phy31: ethernet-phy@31 { + reg = <7>; + }; + phy32: ethernet-phy@32 { + reg = <8>; + }; + phy33: ethernet-phy@33 { + reg = <9>; + }; + phy34: ethernet-phy@34 { + reg = <10>; + }; + phy35: ethernet-phy@35 { + reg = <11>; + }; + phy36: ethernet-phy@36 { + reg = <12>; + }; + phy37: ethernet-phy@37 { + reg = <13>; + }; + phy38: ethernet-phy@38 { + reg = <14>; + }; + phy39: ethernet-phy@39 { + reg = <15>; + }; + phy40: ethernet-phy@40 { + reg = <16>; + }; + phy41: ethernet-phy@41 { + reg = <17>; + }; + phy42: ethernet-phy@42 { + reg = <18>; + }; + phy43: ethernet-phy@43 { + reg = <19>; + }; + phy44: ethernet-phy@44 { + reg = <20>; + }; + phy45: ethernet-phy@45 { + reg = <21>; + }; + phy46: ethernet-phy@46 { + reg = <22>; + }; + phy47: ethernet-phy@47 { + reg = <23>; + }; +}; + +&mdio3 { + status = "ok"; + phy64: ethernet-phy@64 { + reg = <28>; + }; +}; + +&switch { + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port0: port@0 { + reg = <0>; + max-speed = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy0>; + phy-mode = "qsgmii"; + }; + port1: port@1 { + reg = <1>; + max-speed = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy1>; + phy-mode = "qsgmii"; + }; + port2: port@2 { + reg = <2>; + max-speed = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy2>; + phy-mode = "qsgmii"; + }; + port3: port@3 { + reg = <3>; + max-speed = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy3>; + phy-mode = "qsgmii"; + }; + port4: port@4 { + reg = <4>; + max-speed = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy4>; + phy-mode = "qsgmii"; + }; + port5: port@5 { + reg = <5>; + max-speed = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy5>; + phy-mode = "qsgmii"; + }; + port6: port@6 { + reg = <6>; + max-speed = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy6>; + phy-mode = "qsgmii"; + }; + port7: port@7 { + reg = <7>; + max-speed = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy7>; + phy-mode = "qsgmii"; + }; + port8: port@8 { + reg = <8>; + max-speed = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy8>; + phy-mode = "qsgmii"; + }; + port9: port@9 { + reg = <9>; + max-speed = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy9>; + phy-mode = "qsgmii"; + }; + port10: port@10 { + reg = <10>; + max-speed = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy10>; + phy-mode = "qsgmii"; + }; + port11: port@11 { + reg = <11>; + max-speed = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy11>; + phy-mode = "qsgmii"; + }; + port12: port@12 { + reg = <12>; + max-speed = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy12>; + phy-mode = "qsgmii"; + }; + port13: port@13 { + reg = <13>; + max-speed = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy13>; + phy-mode = "qsgmii"; + }; + port14: port@14 { + reg = <14>; + max-speed = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy14>; + phy-mode = "qsgmii"; + }; + port15: port@15 { + reg = <15>; + max-speed = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy15>; + phy-mode = "qsgmii"; + }; + port16: port@16 { + reg = <16>; + max-speed = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy16>; + phy-mode = "qsgmii"; + }; + port17: port@17 { + reg = <17>; + max-speed = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy17>; + phy-mode = "qsgmii"; + }; + port18: port@18 { + reg = <18>; + max-speed = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy18>; + phy-mode = "qsgmii"; + }; + port19: port@19 { + reg = <19>; + max-speed = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy19>; + phy-mode = "qsgmii"; + }; + port20: port@20 { + reg = <20>; + max-speed = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy20>; + phy-mode = "qsgmii"; + }; + port21: port@21 { + reg = <21>; + max-speed = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy21>; + phy-mode = "qsgmii"; + }; + port22: port@22 { + reg = <22>; + max-speed = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy22>; + phy-mode = "qsgmii"; + }; + port23: port@23 { + reg = <23>; + max-speed = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy23>; + phy-mode = "qsgmii"; + }; + port24: port@24 { + reg = <24>; + max-speed = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy24>; + phy-mode = "qsgmii"; + }; + port25: port@25 { + reg = <25>; + max-speed = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy25>; + phy-mode = "qsgmii"; + }; + port26: port@26 { + reg = <26>; + max-speed = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy26>; + phy-mode = "qsgmii"; + }; + port27: port@27 { + reg = <27>; + max-speed = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy27>; + phy-mode = "qsgmii"; + }; + port28: port@28 { + reg = <28>; + max-speed = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy28>; + phy-mode = "qsgmii"; + }; + port29: port@29 { + reg = <29>; + max-speed = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy29>; + phy-mode = "qsgmii"; + }; + port30: port@30 { + reg = <30>; + max-speed = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy30>; + phy-mode = "qsgmii"; + }; + port31: port@31 { + reg = <31>; + max-speed = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy31>; + phy-mode = "qsgmii"; + }; + port32: port@32 { + reg = <32>; + max-speed = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy32>; + phy-mode = "qsgmii"; + }; + port33: port@33 { + reg = <33>; + max-speed = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy33>; + phy-mode = "qsgmii"; + }; + port34: port@34 { + reg = <34>; + max-speed = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy34>; + phy-mode = "qsgmii"; + }; + port35: port@35 { + reg = <35>; + max-speed = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy35>; + phy-mode = "qsgmii"; + }; + port36: port@36 { + reg = <36>; + max-speed = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy36>; + phy-mode = "qsgmii"; + }; + port37: port@37 { + reg = <37>; + max-speed = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy37>; + phy-mode = "qsgmii"; + }; + port38: port@38 { + reg = <38>; + max-speed = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy38>; + phy-mode = "qsgmii"; + }; + port39: port@39 { + reg = <39>; + max-speed = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy39>; + phy-mode = "qsgmii"; + }; + port40: port@40 { + reg = <40>; + max-speed = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy40>; + phy-mode = "qsgmii"; + }; + port41: port@41 { + reg = <41>; + max-speed = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy41>; + phy-mode = "qsgmii"; + }; + port42: port@42 { + reg = <42>; + max-speed = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy42>; + phy-mode = "qsgmii"; + }; + port43: port@43 { + reg = <43>; + max-speed = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy43>; + phy-mode = "qsgmii"; + }; + port44: port@44 { + reg = <44>; + max-speed = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy44>; + phy-mode = "qsgmii"; + }; + port45: port@45 { + reg = <45>; + max-speed = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy45>; + phy-mode = "qsgmii"; + }; + port46: port@46 { + reg = <46>; + max-speed = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy46>; + phy-mode = "qsgmii"; + }; + port47: port@47 { + reg = <47>; + max-speed = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy47>; + phy-mode = "qsgmii"; + }; + /* Then the 25G interfaces */ + port60: port@60 { + reg = <60>; + max-speed = <25000>; + phys = <&serdes 29>; + sfp = <&sfp_eth60>; + managed = "in-band-status"; + }; + port61: port@61 { + reg = <61>; + max-speed = <25000>; + phys = <&serdes 30>; + sfp = <&sfp_eth61>; + managed = "in-band-status"; + }; + port62: port@62 { + reg = <62>; + max-speed = <25000>; + phys = <&serdes 31>; + sfp = <&sfp_eth62>; + managed = "in-band-status"; + }; + port63: port@63 { + reg = <63>; + max-speed = <25000>; + phys = <&serdes 32>; + sfp = <&sfp_eth63>; + managed = "in-band-status"; + }; + /* Finally the Management interface */ + port64: port@64 { + reg = <64>; + max-speed = <1000>; + phys = <&serdes 0>; + phy-handle = <&phy64>; + phy-mode = "sgmii"; + }; + }; +}; -- 2.29.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-12-17 7:53 UTC|newest] Thread overview: 75+ messages / expand[flat|nested] mbox.gz Atom feed top 2020-12-17 7:51 [RFC PATCH v2 0/8] Adding the Sparx5 Switch Driver Steen Hegelund 2020-12-17 7:51 ` Steen Hegelund 2020-12-17 7:51 ` [RFC PATCH v2 1/8] dt-bindings: net: sparx5: Add sparx5-switch bindings Steen Hegelund 2020-12-17 7:51 ` Steen Hegelund 2020-12-19 17:54 ` Andrew Lunn 2020-12-19 17:54 ` Andrew Lunn 2020-12-21 0:55 ` Florian Fainelli 2020-12-21 0:55 ` Florian Fainelli 2020-12-21 10:00 ` Steen Hegelund 2020-12-21 10:00 ` Steen Hegelund 2020-12-21 21:40 ` Rob Herring 2020-12-21 21:40 ` Rob Herring 2020-12-22 7:30 ` Steen Hegelund 2020-12-22 7:30 ` Steen Hegelund 2020-12-17 7:51 ` [RFC PATCH v2 2/8] net: sparx5: add the basic sparx5 driver Steen Hegelund 2020-12-19 19:11 ` Andrew Lunn 2020-12-19 19:11 ` Andrew Lunn 2020-12-22 13:50 ` Steen Hegelund 2020-12-22 13:50 ` Steen Hegelund 2020-12-22 15:01 ` Andrew Lunn 2020-12-22 15:01 ` Andrew Lunn 2020-12-22 16:56 ` Alexandre Belloni 2020-12-22 16:56 ` Alexandre Belloni 2020-12-23 9:03 ` Lars Povlsen 2020-12-23 9:03 ` Lars Povlsen 2020-12-23 8:52 ` Steen Hegelund 2020-12-23 8:52 ` Steen Hegelund 2020-12-17 7:51 ` [RFC PATCH v2 3/8] net: sparx5: add hostmode with phylink support Steen Hegelund 2020-12-17 7:51 ` Steen Hegelund 2020-12-19 19:51 ` Andrew Lunn 2020-12-19 19:51 ` Andrew Lunn 2020-12-22 9:46 ` Steen Hegelund 2020-12-22 9:46 ` Steen Hegelund 2020-12-22 14:41 ` Andrew Lunn 2020-12-22 14:41 ` Andrew Lunn 2020-12-23 13:29 ` Steen Hegelund 2020-12-23 13:29 ` Steen Hegelund 2020-12-23 20:58 ` Alexandre Belloni 2020-12-23 20:58 ` Alexandre Belloni 2020-12-23 21:05 ` Andrew Lunn 2020-12-23 21:05 ` Andrew Lunn 2020-12-17 7:51 ` [RFC PATCH v2 4/8] net: sparx5: add port module support Steen Hegelund 2020-12-17 7:51 ` Steen Hegelund 2020-12-20 23:35 ` Andrew Lunn 2020-12-20 23:35 ` Andrew Lunn 2020-12-22 14:55 ` Bjarni Jonasson 2020-12-22 14:55 ` Bjarni Jonasson 2020-12-22 15:08 ` Andrew Lunn 2020-12-22 15:08 ` Andrew Lunn 2020-12-17 7:51 ` [RFC PATCH v2 5/8] net: sparx5: add switching, vlan and mactable support Steen Hegelund 2020-12-17 7:51 ` Steen Hegelund 2020-12-21 0:25 ` Andrew Lunn 2020-12-21 0:25 ` Andrew Lunn 2020-12-23 13:54 ` Steen Hegelund 2020-12-23 13:54 ` Steen Hegelund 2020-12-17 7:51 ` [RFC PATCH v2 6/8] net: sparx5: add calendar bandwidth allocation support Steen Hegelund 2020-12-17 7:51 ` Steen Hegelund 2020-12-17 7:51 ` [RFC PATCH v2 7/8] net: sparx5: add ethtool configuration and statistics support Steen Hegelund 2020-12-17 7:51 ` Steen Hegelund 2020-12-19 23:31 ` Andrew Lunn 2020-12-19 23:31 ` Andrew Lunn 2020-12-17 7:51 ` Steen Hegelund [this message] 2020-12-17 7:51 ` [RFC PATCH v2 8/8] arm64: dts: sparx5: Add the Sparx5 switch node Steen Hegelund 2020-12-19 20:24 ` Andrew Lunn 2020-12-19 20:24 ` Andrew Lunn 2020-12-23 14:31 ` Steen Hegelund 2020-12-23 14:31 ` Steen Hegelund 2020-12-23 15:49 ` Andrew Lunn 2020-12-23 15:49 ` Andrew Lunn 2020-12-21 0:58 ` [RFC PATCH v2 0/8] Adding the Sparx5 Switch Driver Florian Fainelli 2020-12-21 0:58 ` Florian Fainelli 2020-12-21 14:31 ` Steen Hegelund 2020-12-21 14:31 ` Steen Hegelund 2020-12-22 11:29 ` Lars Povlsen 2020-12-22 11:29 ` Lars Povlsen
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20201217075134.919699-9-steen.hegelund@microchip.com \ --to=steen.hegelund@microchip.com \ --cc=UNGLinuxDriver@microchip.com \ --cc=alexandre.belloni@bootlin.com \ --cc=andrew@lunn.ch \ --cc=arnd@arndb.de \ --cc=bjarni.jonasson@microchip.com \ --cc=davem@davemloft.net \ --cc=devicetree@vger.kernel.org \ --cc=kuba@kernel.org \ --cc=lars.povlsen@microchip.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux@armlinux.org.uk \ --cc=madalin.bucur@oss.nxp.com \ --cc=mark.einon@gmail.com \ --cc=masahiroy@kernel.org \ --cc=netdev@vger.kernel.org \ --cc=nicolas.ferre@microchip.com \ --cc=robh+dt@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.