[PATCH v1 0/7] devicetree fixes for Protonic and Plymovent boards

[PATCH v1 0/7] devicetree fixes for Protonic and Plymovent boards

[Oleksij Rempel]

Oleksij Rempel (7):
  dt-bindings: display: simple: add Innolux G070Y2-T02 panel
  drm: panel-simple: Add support for the Innolux G070Y2-T02 panel
  ARM: dts: imx6dl-prtvt7: Add display and panel nodes
  ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
  ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
  ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
  ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

 .../bindings/display/panel/panel-simple.yaml  |  2 +
 arch/arm/boot/dts/imx6dl-plym2m.dts           |  2 -
 arch/arm/boot/dts/imx6dl-prtvt7.dts           | 79 ++++++++++++++++---
 drivers/gpu/drm/panel/panel-simple.c          | 16 ++++
 4 files changed, 86 insertions(+), 13 deletions(-)

-- 
2.30.0

[PATCH v1 0/7] devicetree fixes for Protonic and Plymovent boards

[Oleksij Rempel]

Oleksij Rempel (7):
  dt-bindings: display: simple: add Innolux G070Y2-T02 panel
  drm: panel-simple: Add support for the Innolux G070Y2-T02 panel
  ARM: dts: imx6dl-prtvt7: Add display and panel nodes
  ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
  ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
  ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
  ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

 .../bindings/display/panel/panel-simple.yaml  |  2 +
 arch/arm/boot/dts/imx6dl-plym2m.dts           |  2 -
 arch/arm/boot/dts/imx6dl-prtvt7.dts           | 79 ++++++++++++++++---
 drivers/gpu/drm/panel/panel-simple.c          | 16 ++++
 4 files changed, 86 insertions(+), 13 deletions(-)

-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 0/7] devicetree fixes for Protonic and Plymovent boards

[Oleksij Rempel]

Oleksij Rempel (7):
  dt-bindings: display: simple: add Innolux G070Y2-T02 panel
  drm: panel-simple: Add support for the Innolux G070Y2-T02 panel
  ARM: dts: imx6dl-prtvt7: Add display and panel nodes
  ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
  ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
  ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
  ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

 .../bindings/display/panel/panel-simple.yaml  |  2 +
 arch/arm/boot/dts/imx6dl-plym2m.dts           |  2 -
 arch/arm/boot/dts/imx6dl-prtvt7.dts           | 79 ++++++++++++++++---
 drivers/gpu/drm/panel/panel-simple.c          | 16 ++++
 4 files changed, 86 insertions(+), 13 deletions(-)

-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v1 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
TFT LCD panel with TTL interface and a backlight unit.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 3207608d1178..f7a1465313db 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -152,6 +152,8 @@ properties:
       - innolux,at070tn92
         # Innolux G070Y2-L01 7" WVGA (800x480) TFT LCD panel
       - innolux,g070y2-l01
+        # Innolux G070Y2-T02 7" WVGA (800x480) TFT LCD TTL panel
+      - innolux,g070y2-t02
         # Innolux Corporation 10.1" G101ICE-L01 WXGA (1280x800) LVDS panel
       - innolux,g101ice-l01
         # Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel
-- 
2.30.0

[PATCH v1 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
TFT LCD panel with TTL interface and a backlight unit.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 3207608d1178..f7a1465313db 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -152,6 +152,8 @@ properties:
       - innolux,at070tn92
         # Innolux G070Y2-L01 7" WVGA (800x480) TFT LCD panel
       - innolux,g070y2-l01
+        # Innolux G070Y2-T02 7" WVGA (800x480) TFT LCD TTL panel
+      - innolux,g070y2-t02
         # Innolux Corporation 10.1" G101ICE-L01 WXGA (1280x800) LVDS panel
       - innolux,g101ice-l01
         # Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
TFT LCD panel with TTL interface and a backlight unit.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 3207608d1178..f7a1465313db 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -152,6 +152,8 @@ properties:
       - innolux,at070tn92
         # Innolux G070Y2-L01 7" WVGA (800x480) TFT LCD panel
       - innolux,g070y2-l01
+        # Innolux G070Y2-T02 7" WVGA (800x480) TFT LCD TTL panel
+      - innolux,g070y2-t02
         # Innolux Corporation 10.1" G101ICE-L01 WXGA (1280x800) LVDS panel
       - innolux,g101ice-l01
         # Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v1 2/7] drm: panel-simple: Add support for the Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add compatible and timings for the Innolux G070Y2-T02 panel. It is 7"
WVGA (800x480) TFT LCD panel with TTL interface and a backlight unit.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/gpu/drm/panel/panel-simple.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 41bbec72b2da..14996ca264f3 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -2149,6 +2149,19 @@ static const struct panel_desc innolux_g070y2_l01 = {
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
+static const struct panel_desc innolux_g070y2_t02 = {
+	.modes = &innolux_at070tn92_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 152,
+		.height = 92,
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
+	.connector_type = DRM_MODE_CONNECTOR_DPI,
+};
+
 static const struct display_timing innolux_g101ice_l01_timing = {
 	.pixelclock = { 60400000, 71100000, 74700000 },
 	.hactive = { 1280, 1280, 1280 },
@@ -4135,6 +4148,9 @@ static const struct of_device_id platform_of_match[] = {
 	}, {
 		.compatible = "innolux,g070y2-l01",
 		.data = &innolux_g070y2_l01,
+	}, {
+		.compatible = "innolux,g070y2-t02",
+		.data = &innolux_g070y2_t02,
 	}, {
 		.compatible = "innolux,g101ice-l01",
 		.data = &innolux_g101ice_l01
-- 
2.30.0

[PATCH v1 2/7] drm: panel-simple: Add support for the Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add compatible and timings for the Innolux G070Y2-T02 panel. It is 7"
WVGA (800x480) TFT LCD panel with TTL interface and a backlight unit.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/gpu/drm/panel/panel-simple.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 41bbec72b2da..14996ca264f3 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -2149,6 +2149,19 @@ static const struct panel_desc innolux_g070y2_l01 = {
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
+static const struct panel_desc innolux_g070y2_t02 = {
+	.modes = &innolux_at070tn92_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 152,
+		.height = 92,
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
+	.connector_type = DRM_MODE_CONNECTOR_DPI,
+};
+
 static const struct display_timing innolux_g101ice_l01_timing = {
 	.pixelclock = { 60400000, 71100000, 74700000 },
 	.hactive = { 1280, 1280, 1280 },
@@ -4135,6 +4148,9 @@ static const struct of_device_id platform_of_match[] = {
 	}, {
 		.compatible = "innolux,g070y2-l01",
 		.data = &innolux_g070y2_l01,
+	}, {
+		.compatible = "innolux,g070y2-t02",
+		.data = &innolux_g070y2_t02,
 	}, {
 		.compatible = "innolux,g101ice-l01",
 		.data = &innolux_g101ice_l01
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 2/7] drm: panel-simple: Add support for the Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add compatible and timings for the Innolux G070Y2-T02 panel. It is 7"
WVGA (800x480) TFT LCD panel with TTL interface and a backlight unit.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/gpu/drm/panel/panel-simple.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 41bbec72b2da..14996ca264f3 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -2149,6 +2149,19 @@ static const struct panel_desc innolux_g070y2_l01 = {
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
+static const struct panel_desc innolux_g070y2_t02 = {
+	.modes = &innolux_at070tn92_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 152,
+		.height = 92,
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
+	.connector_type = DRM_MODE_CONNECTOR_DPI,
+};
+
 static const struct display_timing innolux_g101ice_l01_timing = {
 	.pixelclock = { 60400000, 71100000, 74700000 },
 	.hactive = { 1280, 1280, 1280 },
@@ -4135,6 +4148,9 @@ static const struct of_device_id platform_of_match[] = {
 	}, {
 		.compatible = "innolux,g070y2-l01",
 		.data = &innolux_g070y2_l01,
+	}, {
+		.compatible = "innolux,g070y2-t02",
+		.data = &innolux_g070y2_t02,
 	}, {
 		.compatible = "innolux,g101ice-l01",
 		.data = &innolux_g101ice_l01
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v1 3/7] ARM: dts: imx6dl-prtvt7: Add display and panel nodes

[Oleksij Rempel]

Add Innolux G070Y2-T02 panel to the Protonic VT7 board.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 47 +++++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index ae6da241f13e..d9cb1e41cc10 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -31,6 +31,30 @@ backlight_lcd: backlight-lcd {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
 	keys {
 		compatible = "gpio-keys";
 		autorepeat;
@@ -138,6 +162,18 @@ led-debug0 {
 		};
 	};
 
+	panel {
+		compatible = "innolux,g070y2-t02";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	reg_bl_12v0: regulator-bl-12v0 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -149,6 +185,13 @@ reg_bl_12v0: regulator-bl-12v0 {
 		enable-active-high;
 	};
 
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_1v8: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "1v8";
@@ -260,6 +303,10 @@ &ipu1 {
 	status = "okay";
 };
 
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
 &pwm1 {
 	#pwm-cells = <2>;
 	pinctrl-names = "default";
-- 
2.30.0

[PATCH v1 3/7] ARM: dts: imx6dl-prtvt7: Add display and panel nodes

[Oleksij Rempel]

Add Innolux G070Y2-T02 panel to the Protonic VT7 board.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 47 +++++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index ae6da241f13e..d9cb1e41cc10 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -31,6 +31,30 @@ backlight_lcd: backlight-lcd {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
 	keys {
 		compatible = "gpio-keys";
 		autorepeat;
@@ -138,6 +162,18 @@ led-debug0 {
 		};
 	};
 
+	panel {
+		compatible = "innolux,g070y2-t02";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	reg_bl_12v0: regulator-bl-12v0 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -149,6 +185,13 @@ reg_bl_12v0: regulator-bl-12v0 {
 		enable-active-high;
 	};
 
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_1v8: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "1v8";
@@ -260,6 +303,10 @@ &ipu1 {
 	status = "okay";
 };
 
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
 &pwm1 {
 	#pwm-cells = <2>;
 	pinctrl-names = "default";
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 3/7] ARM: dts: imx6dl-prtvt7: Add display and panel nodes

[Oleksij Rempel]

Add Innolux G070Y2-T02 panel to the Protonic VT7 board.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 47 +++++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index ae6da241f13e..d9cb1e41cc10 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -31,6 +31,30 @@ backlight_lcd: backlight-lcd {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
 	keys {
 		compatible = "gpio-keys";
 		autorepeat;
@@ -138,6 +162,18 @@ led-debug0 {
 		};
 	};
 
+	panel {
+		compatible = "innolux,g070y2-t02";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	reg_bl_12v0: regulator-bl-12v0 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -149,6 +185,13 @@ reg_bl_12v0: regulator-bl-12v0 {
 		enable-active-high;
 	};
 
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_1v8: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "1v8";
@@ -260,6 +303,10 @@ &ipu1 {
 	status = "okay";
 };
 
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
 &pwm1 {
 	#pwm-cells = <2>;
 	pinctrl-names = "default";
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node

[Oleksij Rempel]

Add touchscreen support to the Protonic VT7 board.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index d9cb1e41cc10..63ae2065834c 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -266,6 +266,26 @@ &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
+
+	touchscreen@0 {
+		compatible = "ti,tsc2046";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_tsc>;
+		pinctrl-names ="default";
+		spi-max-frequency = <100000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		touchscreen-max-pressure = <4095>;
+
+		ti,vref-delay-usecs = /bits/ 16 <100>;
+		ti,x-plate-ohms = /bits/ 16 <800>;
+		ti,y-plate-ohms = /bits/ 16 <300>;
+
+		wakeup-source;
+	};
 };
 
 &i2c1 {
-- 
2.30.0

[PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node

[Oleksij Rempel]

Add touchscreen support to the Protonic VT7 board.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index d9cb1e41cc10..63ae2065834c 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -266,6 +266,26 @@ &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
+
+	touchscreen@0 {
+		compatible = "ti,tsc2046";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_tsc>;
+		pinctrl-names ="default";
+		spi-max-frequency = <100000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		touchscreen-max-pressure = <4095>;
+
+		ti,vref-delay-usecs = /bits/ 16 <100>;
+		ti,x-plate-ohms = /bits/ 16 <800>;
+		ti,y-plate-ohms = /bits/ 16 <300>;
+
+		wakeup-source;
+	};
 };
 
 &i2c1 {
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node

[Oleksij Rempel]

Add touchscreen support to the Protonic VT7 board.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index d9cb1e41cc10..63ae2065834c 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -266,6 +266,26 @@ &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
+
+	touchscreen@0 {
+		compatible = "ti,tsc2046";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_tsc>;
+		pinctrl-names ="default";
+		spi-max-frequency = <100000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		touchscreen-max-pressure = <4095>;
+
+		ti,vref-delay-usecs = /bits/ 16 <100>;
+		ti,x-plate-ohms = /bits/ 16 <800>;
+		ti,y-plate-ohms = /bits/ 16 <300>;
+
+		wakeup-source;
+	};
 };
 
 &i2c1 {
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v1 5/7] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio

[Oleksij Rempel]

The backlight power is controlled through the reg_bl_12v0 regulator.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 9 ---------
 1 file changed, 9 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 63ae2065834c..fe8df03c8bfb 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,14 +21,11 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_backlight>;
 		pwms = <&pwm1 0 500000>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
 		power-supply = <&reg_bl_12v0>;
-		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
 	display {
@@ -367,12 +364,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
 		>;
 	};
 
-	pinctrl_backlight: backlightgrp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28	0x1b0b0
-		>;
-	};
-
 	pinctrl_can1phy: can1phy {
 		fsl,pins = <
 			/* CAN1_SR */
-- 
2.30.0

[PATCH v1 5/7] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio

[Oleksij Rempel]

The backlight power is controlled through the reg_bl_12v0 regulator.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 9 ---------
 1 file changed, 9 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 63ae2065834c..fe8df03c8bfb 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,14 +21,11 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_backlight>;
 		pwms = <&pwm1 0 500000>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
 		power-supply = <&reg_bl_12v0>;
-		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
 	display {
@@ -367,12 +364,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
 		>;
 	};
 
-	pinctrl_backlight: backlightgrp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28	0x1b0b0
-		>;
-	};
-
 	pinctrl_can1phy: can1phy {
 		fsl,pins = <
 			/* CAN1_SR */
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 5/7] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio

[Oleksij Rempel]

The backlight power is controlled through the reg_bl_12v0 regulator.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 9 ---------
 1 file changed, 9 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 63ae2065834c..fe8df03c8bfb 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,14 +21,11 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_backlight>;
 		pwms = <&pwm1 0 500000>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
 		power-supply = <&reg_bl_12v0>;
-		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
 	display {
@@ -367,12 +364,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
 		>;
 	};
 
-	pinctrl_backlight: backlightgrp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28	0x1b0b0
-		>;
-	};
-
 	pinctrl_can1phy: can1phy {
 		fsl,pins = <
 			/* CAN1_SR */
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v1 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Oleksij Rempel]

At some point PWM cell count was changed, but it didn't triggered any
error, since this DT was overwriting "#pwm-cells".
To make sure, we are in sync with the kernel driver, remove this
property and fix the pwm consumer.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index fe8df03c8bfb..35d06ba93c88 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,7 +21,7 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 500000>;
+		pwms = <&pwm1 0 500000 0>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
@@ -325,7 +325,6 @@ &ipu1_di0_disp0 {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.30.0

[PATCH v1 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Oleksij Rempel]

At some point PWM cell count was changed, but it didn't triggered any
error, since this DT was overwriting "#pwm-cells".
To make sure, we are in sync with the kernel driver, remove this
property and fix the pwm consumer.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index fe8df03c8bfb..35d06ba93c88 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,7 +21,7 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 500000>;
+		pwms = <&pwm1 0 500000 0>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
@@ -325,7 +325,6 @@ &ipu1_di0_disp0 {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Oleksij Rempel]

At some point PWM cell count was changed, but it didn't triggered any
error, since this DT was overwriting "#pwm-cells".
To make sure, we are in sync with the kernel driver, remove this
property and fix the pwm consumer.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index fe8df03c8bfb..35d06ba93c88 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,7 +21,7 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 500000>;
+		pwms = <&pwm1 0 500000 0>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
@@ -325,7 +325,6 @@ &ipu1_di0_disp0 {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v1 7/7] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

[Oleksij Rempel]

Remove touchscreen-size-* properties.  This values are not correct, event if it
works with ts_test tool, it fails to work properly with weston.
And the real range of values reported by the driver (or measured by the
controller) is close to max values and may change with time on resistive
panels. So, it make no sense to keep this values in the device tree.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-plym2m.dts | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 4d0d3d3386af..c97274f0df07 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -138,8 +138,6 @@ touchscreen@0 {
 		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
 		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
 
-		touchscreen-size-x = <800>;
-		touchscreen-size-y = <480>;
 		touchscreen-inverted-x;
 		touchscreen-inverted-y;
 		touchscreen-max-pressure = <4095>;
-- 
2.30.0

[PATCH v1 7/7] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

[Oleksij Rempel]

Remove touchscreen-size-* properties.  This values are not correct, event if it
works with ts_test tool, it fails to work properly with weston.
And the real range of values reported by the driver (or measured by the
controller) is close to max values and may change with time on resistive
panels. So, it make no sense to keep this values in the device tree.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-plym2m.dts | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 4d0d3d3386af..c97274f0df07 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -138,8 +138,6 @@ touchscreen@0 {
 		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
 		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
 
-		touchscreen-size-x = <800>;
-		touchscreen-size-y = <480>;
 		touchscreen-inverted-x;
 		touchscreen-inverted-y;
 		touchscreen-max-pressure = <4095>;
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 7/7] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

[Oleksij Rempel]

Remove touchscreen-size-* properties.  This values are not correct, event if it
works with ts_test tool, it fails to work properly with weston.
And the real range of values reported by the driver (or measured by the
controller) is close to max values and may change with time on resistive
panels. So, it make no sense to keep this values in the device tree.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-plym2m.dts | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 4d0d3d3386af..c97274f0df07 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -138,8 +138,6 @@ touchscreen@0 {
 		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
 		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
 
-		touchscreen-size-x = <800>;
-		touchscreen-size-y = <480>;
 		touchscreen-inverted-x;
 		touchscreen-inverted-y;
 		touchscreen-max-pressure = <4095>;
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node

[robin]

On 2021-01-20 15:22, Oleksij Rempel wrote:
> Add touchscreen support to the Protonic VT7 board.
> 
> Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
>  1 file changed, 20 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> index d9cb1e41cc10..63ae2065834c 100644
> --- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> @@ -266,6 +266,26 @@ &ecspi2 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_ecspi2>;
>  	status = "okay";
> +
> +	touchscreen@0 {
> +		compatible = "ti,tsc2046";
> +		reg = <0>;
> +		pinctrl-0 = <&pinctrl_tsc>;
> +		pinctrl-names ="default";
> +		spi-max-frequency = <100000>;
> +		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
> +		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
> +
> +		touchscreen-inverted-x;
> +		touchscreen-inverted-y;

Please remove both inverted properties since it's not inverted.

> +		touchscreen-max-pressure = <4095>;
> +
> +		ti,vref-delay-usecs = /bits/ 16 <100>;
> +		ti,x-plate-ohms = /bits/ 16 <800>;
> +		ti,y-plate-ohms = /bits/ 16 <300>;
> +
> +		wakeup-source;
> +	};
>  };
> 
>  &i2c1 {

Robin

Re: [PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node

[robin]

On 2021-01-20 15:22, Oleksij Rempel wrote:
> Add touchscreen support to the Protonic VT7 board.
> 
> Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
>  1 file changed, 20 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> index d9cb1e41cc10..63ae2065834c 100644
> --- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> @@ -266,6 +266,26 @@ &ecspi2 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_ecspi2>;
>  	status = "okay";
> +
> +	touchscreen@0 {
> +		compatible = "ti,tsc2046";
> +		reg = <0>;
> +		pinctrl-0 = <&pinctrl_tsc>;
> +		pinctrl-names ="default";
> +		spi-max-frequency = <100000>;
> +		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
> +		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
> +
> +		touchscreen-inverted-x;
> +		touchscreen-inverted-y;

Please remove both inverted properties since it's not inverted.

> +		touchscreen-max-pressure = <4095>;
> +
> +		ti,vref-delay-usecs = /bits/ 16 <100>;
> +		ti,x-plate-ohms = /bits/ 16 <800>;
> +		ti,y-plate-ohms = /bits/ 16 <300>;
> +
> +		wakeup-source;
> +	};
>  };
> 
>  &i2c1 {

Robin

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node

[robin]

On 2021-01-20 15:22, Oleksij Rempel wrote:
> Add touchscreen support to the Protonic VT7 board.
> 
> Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
>  1 file changed, 20 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> index d9cb1e41cc10..63ae2065834c 100644
> --- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> @@ -266,6 +266,26 @@ &ecspi2 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_ecspi2>;
>  	status = "okay";
> +
> +	touchscreen@0 {
> +		compatible = "ti,tsc2046";
> +		reg = <0>;
> +		pinctrl-0 = <&pinctrl_tsc>;
> +		pinctrl-names ="default";
> +		spi-max-frequency = <100000>;
> +		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
> +		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
> +
> +		touchscreen-inverted-x;
> +		touchscreen-inverted-y;

Please remove both inverted properties since it's not inverted.

> +		touchscreen-max-pressure = <4095>;
> +
> +		ti,vref-delay-usecs = /bits/ 16 <100>;
> +		ti,x-plate-ohms = /bits/ 16 <800>;
> +		ti,y-plate-ohms = /bits/ 16 <300>;
> +
> +		wakeup-source;
> +	};
>  };
> 
>  &i2c1 {

Robin
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel