* [PATCH v1 0/7] devicetree fixes for Protonic and Plymovent boards
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, linux-arm-kernel
Oleksij Rempel (7):
dt-bindings: display: simple: add Innolux G070Y2-T02 panel
drm: panel-simple: Add support for the Innolux G070Y2-T02 panel
ARM: dts: imx6dl-prtvt7: Add display and panel nodes
ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties
.../bindings/display/panel/panel-simple.yaml | 2 +
arch/arm/boot/dts/imx6dl-plym2m.dts | 2 -
arch/arm/boot/dts/imx6dl-prtvt7.dts | 79 ++++++++++++++++---
drivers/gpu/drm/panel/panel-simple.c | 16 ++++
4 files changed, 86 insertions(+), 13 deletions(-)
--
2.30.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH v1 0/7] devicetree fixes for Protonic and Plymovent boards
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Fabio Estevam, linux-arm-kernel
Oleksij Rempel (7):
dt-bindings: display: simple: add Innolux G070Y2-T02 panel
drm: panel-simple: Add support for the Innolux G070Y2-T02 panel
ARM: dts: imx6dl-prtvt7: Add display and panel nodes
ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties
.../bindings/display/panel/panel-simple.yaml | 2 +
arch/arm/boot/dts/imx6dl-plym2m.dts | 2 -
arch/arm/boot/dts/imx6dl-prtvt7.dts | 79 ++++++++++++++++---
drivers/gpu/drm/panel/panel-simple.c | 16 ++++
4 files changed, 86 insertions(+), 13 deletions(-)
--
2.30.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH v1 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel
2021-01-20 14:22 ` Oleksij Rempel
(?)
@ 2021-01-20 14:22 ` Oleksij Rempel
-1 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Robin van der Gracht, dri-devel
Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
TFT LCD panel with TTL interface and a backlight unit.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/display/panel/panel-simple.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 3207608d1178..f7a1465313db 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -152,6 +152,8 @@ properties:
- innolux,at070tn92
# Innolux G070Y2-L01 7" WVGA (800x480) TFT LCD panel
- innolux,g070y2-l01
+ # Innolux G070Y2-T02 7" WVGA (800x480) TFT LCD TTL panel
+ - innolux,g070y2-t02
# Innolux Corporation 10.1" G101ICE-L01 WXGA (1280x800) LVDS panel
- innolux,g101ice-l01
# Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel
--
2.30.0
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, linux-arm-kernel
Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
TFT LCD panel with TTL interface and a backlight unit.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/display/panel/panel-simple.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 3207608d1178..f7a1465313db 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -152,6 +152,8 @@ properties:
- innolux,at070tn92
# Innolux G070Y2-L01 7" WVGA (800x480) TFT LCD panel
- innolux,g070y2-l01
+ # Innolux G070Y2-T02 7" WVGA (800x480) TFT LCD TTL panel
+ - innolux,g070y2-t02
# Innolux Corporation 10.1" G101ICE-L01 WXGA (1280x800) LVDS panel
- innolux,g101ice-l01
# Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel
--
2.30.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Fabio Estevam, linux-arm-kernel
Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
TFT LCD panel with TTL interface and a backlight unit.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/display/panel/panel-simple.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 3207608d1178..f7a1465313db 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -152,6 +152,8 @@ properties:
- innolux,at070tn92
# Innolux G070Y2-L01 7" WVGA (800x480) TFT LCD panel
- innolux,g070y2-l01
+ # Innolux G070Y2-T02 7" WVGA (800x480) TFT LCD TTL panel
+ - innolux,g070y2-t02
# Innolux Corporation 10.1" G101ICE-L01 WXGA (1280x800) LVDS panel
- innolux,g101ice-l01
# Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel
--
2.30.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 2/7] drm: panel-simple: Add support for the Innolux G070Y2-T02 panel
2021-01-20 14:22 ` Oleksij Rempel
(?)
@ 2021-01-20 14:22 ` Oleksij Rempel
-1 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, Robin van der Gracht, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander, dri-devel
Add compatible and timings for the Innolux G070Y2-T02 panel. It is 7"
WVGA (800x480) TFT LCD panel with TTL interface and a backlight unit.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
drivers/gpu/drm/panel/panel-simple.c | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 41bbec72b2da..14996ca264f3 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -2149,6 +2149,19 @@ static const struct panel_desc innolux_g070y2_l01 = {
.connector_type = DRM_MODE_CONNECTOR_LVDS,
};
+static const struct panel_desc innolux_g070y2_t02 = {
+ .modes = &innolux_at070tn92_mode,
+ .num_modes = 1,
+ .bpc = 8,
+ .size = {
+ .width = 152,
+ .height = 92,
+ },
+ .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+ .bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
+ .connector_type = DRM_MODE_CONNECTOR_DPI,
+};
+
static const struct display_timing innolux_g101ice_l01_timing = {
.pixelclock = { 60400000, 71100000, 74700000 },
.hactive = { 1280, 1280, 1280 },
@@ -4135,6 +4148,9 @@ static const struct of_device_id platform_of_match[] = {
}, {
.compatible = "innolux,g070y2-l01",
.data = &innolux_g070y2_l01,
+ }, {
+ .compatible = "innolux,g070y2-t02",
+ .data = &innolux_g070y2_t02,
}, {
.compatible = "innolux,g101ice-l01",
.data = &innolux_g101ice_l01
--
2.30.0
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 2/7] drm: panel-simple: Add support for the Innolux G070Y2-T02 panel
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, linux-arm-kernel
Add compatible and timings for the Innolux G070Y2-T02 panel. It is 7"
WVGA (800x480) TFT LCD panel with TTL interface and a backlight unit.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
drivers/gpu/drm/panel/panel-simple.c | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 41bbec72b2da..14996ca264f3 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -2149,6 +2149,19 @@ static const struct panel_desc innolux_g070y2_l01 = {
.connector_type = DRM_MODE_CONNECTOR_LVDS,
};
+static const struct panel_desc innolux_g070y2_t02 = {
+ .modes = &innolux_at070tn92_mode,
+ .num_modes = 1,
+ .bpc = 8,
+ .size = {
+ .width = 152,
+ .height = 92,
+ },
+ .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+ .bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
+ .connector_type = DRM_MODE_CONNECTOR_DPI,
+};
+
static const struct display_timing innolux_g101ice_l01_timing = {
.pixelclock = { 60400000, 71100000, 74700000 },
.hactive = { 1280, 1280, 1280 },
@@ -4135,6 +4148,9 @@ static const struct of_device_id platform_of_match[] = {
}, {
.compatible = "innolux,g070y2-l01",
.data = &innolux_g070y2_l01,
+ }, {
+ .compatible = "innolux,g070y2-t02",
+ .data = &innolux_g070y2_t02,
}, {
.compatible = "innolux,g101ice-l01",
.data = &innolux_g101ice_l01
--
2.30.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 2/7] drm: panel-simple: Add support for the Innolux G070Y2-T02 panel
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Fabio Estevam, linux-arm-kernel
Add compatible and timings for the Innolux G070Y2-T02 panel. It is 7"
WVGA (800x480) TFT LCD panel with TTL interface and a backlight unit.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
drivers/gpu/drm/panel/panel-simple.c | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 41bbec72b2da..14996ca264f3 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -2149,6 +2149,19 @@ static const struct panel_desc innolux_g070y2_l01 = {
.connector_type = DRM_MODE_CONNECTOR_LVDS,
};
+static const struct panel_desc innolux_g070y2_t02 = {
+ .modes = &innolux_at070tn92_mode,
+ .num_modes = 1,
+ .bpc = 8,
+ .size = {
+ .width = 152,
+ .height = 92,
+ },
+ .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+ .bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
+ .connector_type = DRM_MODE_CONNECTOR_DPI,
+};
+
static const struct display_timing innolux_g101ice_l01_timing = {
.pixelclock = { 60400000, 71100000, 74700000 },
.hactive = { 1280, 1280, 1280 },
@@ -4135,6 +4148,9 @@ static const struct of_device_id platform_of_match[] = {
}, {
.compatible = "innolux,g070y2-l01",
.data = &innolux_g070y2_l01,
+ }, {
+ .compatible = "innolux,g070y2-t02",
+ .data = &innolux_g070y2_t02,
}, {
.compatible = "innolux,g101ice-l01",
.data = &innolux_g101ice_l01
--
2.30.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 3/7] ARM: dts: imx6dl-prtvt7: Add display and panel nodes
2021-01-20 14:22 ` Oleksij Rempel
(?)
@ 2021-01-20 14:22 ` Oleksij Rempel
-1 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, Robin van der Gracht, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander, dri-devel
Add Innolux G070Y2-T02 panel to the Protonic VT7 board.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 47 +++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index ae6da241f13e..d9cb1e41cc10 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -31,6 +31,30 @@ backlight_lcd: backlight-lcd {
enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
};
+ display {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
keys {
compatible = "gpio-keys";
autorepeat;
@@ -138,6 +162,18 @@ led-debug0 {
};
};
+ panel {
+ compatible = "innolux,g070y2-t02";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
reg_bl_12v0: regulator-bl-12v0 {
compatible = "regulator-fixed";
pinctrl-names = "default";
@@ -149,6 +185,13 @@ reg_bl_12v0: regulator-bl-12v0 {
enable-active-high;
};
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
reg_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "1v8";
@@ -260,6 +303,10 @@ &ipu1 {
status = "okay";
};
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
&pwm1 {
#pwm-cells = <2>;
pinctrl-names = "default";
--
2.30.0
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 3/7] ARM: dts: imx6dl-prtvt7: Add display and panel nodes
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, linux-arm-kernel
Add Innolux G070Y2-T02 panel to the Protonic VT7 board.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 47 +++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index ae6da241f13e..d9cb1e41cc10 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -31,6 +31,30 @@ backlight_lcd: backlight-lcd {
enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
};
+ display {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
keys {
compatible = "gpio-keys";
autorepeat;
@@ -138,6 +162,18 @@ led-debug0 {
};
};
+ panel {
+ compatible = "innolux,g070y2-t02";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
reg_bl_12v0: regulator-bl-12v0 {
compatible = "regulator-fixed";
pinctrl-names = "default";
@@ -149,6 +185,13 @@ reg_bl_12v0: regulator-bl-12v0 {
enable-active-high;
};
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
reg_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "1v8";
@@ -260,6 +303,10 @@ &ipu1 {
status = "okay";
};
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
&pwm1 {
#pwm-cells = <2>;
pinctrl-names = "default";
--
2.30.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 3/7] ARM: dts: imx6dl-prtvt7: Add display and panel nodes
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Fabio Estevam, linux-arm-kernel
Add Innolux G070Y2-T02 panel to the Protonic VT7 board.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 47 +++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index ae6da241f13e..d9cb1e41cc10 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -31,6 +31,30 @@ backlight_lcd: backlight-lcd {
enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
};
+ display {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
keys {
compatible = "gpio-keys";
autorepeat;
@@ -138,6 +162,18 @@ led-debug0 {
};
};
+ panel {
+ compatible = "innolux,g070y2-t02";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
reg_bl_12v0: regulator-bl-12v0 {
compatible = "regulator-fixed";
pinctrl-names = "default";
@@ -149,6 +185,13 @@ reg_bl_12v0: regulator-bl-12v0 {
enable-active-high;
};
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
reg_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "1v8";
@@ -260,6 +303,10 @@ &ipu1 {
status = "okay";
};
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
&pwm1 {
#pwm-cells = <2>;
pinctrl-names = "default";
--
2.30.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
2021-01-20 14:22 ` Oleksij Rempel
(?)
@ 2021-01-20 14:22 ` Oleksij Rempel
-1 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, Robin van der Gracht, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander, dri-devel
Add touchscreen support to the Protonic VT7 board.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index d9cb1e41cc10..63ae2065834c 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -266,6 +266,26 @@ &ecspi2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
+
+ touchscreen@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ pinctrl-0 = <&pinctrl_tsc>;
+ pinctrl-names ="default";
+ spi-max-frequency = <100000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+ pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ touchscreen-max-pressure = <4095>;
+
+ ti,vref-delay-usecs = /bits/ 16 <100>;
+ ti,x-plate-ohms = /bits/ 16 <800>;
+ ti,y-plate-ohms = /bits/ 16 <300>;
+
+ wakeup-source;
+ };
};
&i2c1 {
--
2.30.0
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, linux-arm-kernel
Add touchscreen support to the Protonic VT7 board.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index d9cb1e41cc10..63ae2065834c 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -266,6 +266,26 @@ &ecspi2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
+
+ touchscreen@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ pinctrl-0 = <&pinctrl_tsc>;
+ pinctrl-names ="default";
+ spi-max-frequency = <100000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+ pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ touchscreen-max-pressure = <4095>;
+
+ ti,vref-delay-usecs = /bits/ 16 <100>;
+ ti,x-plate-ohms = /bits/ 16 <800>;
+ ti,y-plate-ohms = /bits/ 16 <300>;
+
+ wakeup-source;
+ };
};
&i2c1 {
--
2.30.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Fabio Estevam, linux-arm-kernel
Add touchscreen support to the Protonic VT7 board.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index d9cb1e41cc10..63ae2065834c 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -266,6 +266,26 @@ &ecspi2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
+
+ touchscreen@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ pinctrl-0 = <&pinctrl_tsc>;
+ pinctrl-names ="default";
+ spi-max-frequency = <100000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+ pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ touchscreen-max-pressure = <4095>;
+
+ ti,vref-delay-usecs = /bits/ 16 <100>;
+ ti,x-plate-ohms = /bits/ 16 <800>;
+ ti,y-plate-ohms = /bits/ 16 <300>;
+
+ wakeup-source;
+ };
};
&i2c1 {
--
2.30.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* Re: [PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
2021-01-20 14:22 ` Oleksij Rempel
(?)
@ 2021-01-20 14:47 ` robin
-1 siblings, 0 replies; 27+ messages in thread
From: robin @ 2021-01-20 14:47 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter,
devicetree, Fabio Estevam, linux-arm-kernel, linux-kernel,
NXP Linux Team, Pengutronix Kernel Team, David Jander, dri-devel
On 2021-01-20 15:22, Oleksij Rempel wrote:
> Add touchscreen support to the Protonic VT7 board.
>
> Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
> 1 file changed, 20 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> index d9cb1e41cc10..63ae2065834c 100644
> --- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> @@ -266,6 +266,26 @@ &ecspi2 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_ecspi2>;
> status = "okay";
> +
> + touchscreen@0 {
> + compatible = "ti,tsc2046";
> + reg = <0>;
> + pinctrl-0 = <&pinctrl_tsc>;
> + pinctrl-names ="default";
> + spi-max-frequency = <100000>;
> + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
> + pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
> +
> + touchscreen-inverted-x;
> + touchscreen-inverted-y;
Please remove both inverted properties since it's not inverted.
> + touchscreen-max-pressure = <4095>;
> +
> + ti,vref-delay-usecs = /bits/ 16 <100>;
> + ti,x-plate-ohms = /bits/ 16 <800>;
> + ti,y-plate-ohms = /bits/ 16 <300>;
> +
> + wakeup-source;
> + };
> };
>
> &i2c1 {
Robin
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
@ 2021-01-20 14:47 ` robin
0 siblings, 0 replies; 27+ messages in thread
From: robin @ 2021-01-20 14:47 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, devicetree, Pengutronix Kernel Team, dri-devel,
David Airlie, Sam Ravnborg, Sascha Hauer, linux-kernel,
Rob Herring, Thierry Reding, NXP Linux Team, David Jander,
Shawn Guo, linux-arm-kernel
On 2021-01-20 15:22, Oleksij Rempel wrote:
> Add touchscreen support to the Protonic VT7 board.
>
> Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
> 1 file changed, 20 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> index d9cb1e41cc10..63ae2065834c 100644
> --- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> @@ -266,6 +266,26 @@ &ecspi2 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_ecspi2>;
> status = "okay";
> +
> + touchscreen@0 {
> + compatible = "ti,tsc2046";
> + reg = <0>;
> + pinctrl-0 = <&pinctrl_tsc>;
> + pinctrl-names ="default";
> + spi-max-frequency = <100000>;
> + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
> + pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
> +
> + touchscreen-inverted-x;
> + touchscreen-inverted-y;
Please remove both inverted properties since it's not inverted.
> + touchscreen-max-pressure = <4095>;
> +
> + ti,vref-delay-usecs = /bits/ 16 <100>;
> + ti,x-plate-ohms = /bits/ 16 <800>;
> + ti,y-plate-ohms = /bits/ 16 <300>;
> +
> + wakeup-source;
> + };
> };
>
> &i2c1 {
Robin
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v1 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
@ 2021-01-20 14:47 ` robin
0 siblings, 0 replies; 27+ messages in thread
From: robin @ 2021-01-20 14:47 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, devicetree, Fabio Estevam, Pengutronix Kernel Team,
dri-devel, David Airlie, Sam Ravnborg, Sascha Hauer,
linux-kernel, Rob Herring, Thierry Reding, NXP Linux Team,
Daniel Vetter, David Jander, Shawn Guo, linux-arm-kernel
On 2021-01-20 15:22, Oleksij Rempel wrote:
> Add touchscreen support to the Protonic VT7 board.
>
> Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> arch/arm/boot/dts/imx6dl-prtvt7.dts | 20 ++++++++++++++++++++
> 1 file changed, 20 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> index d9cb1e41cc10..63ae2065834c 100644
> --- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> @@ -266,6 +266,26 @@ &ecspi2 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_ecspi2>;
> status = "okay";
> +
> + touchscreen@0 {
> + compatible = "ti,tsc2046";
> + reg = <0>;
> + pinctrl-0 = <&pinctrl_tsc>;
> + pinctrl-names ="default";
> + spi-max-frequency = <100000>;
> + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
> + pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
> +
> + touchscreen-inverted-x;
> + touchscreen-inverted-y;
Please remove both inverted properties since it's not inverted.
> + touchscreen-max-pressure = <4095>;
> +
> + ti,vref-delay-usecs = /bits/ 16 <100>;
> + ti,x-plate-ohms = /bits/ 16 <800>;
> + ti,y-plate-ohms = /bits/ 16 <300>;
> +
> + wakeup-source;
> + };
> };
>
> &i2c1 {
Robin
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH v1 5/7] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
2021-01-20 14:22 ` Oleksij Rempel
(?)
@ 2021-01-20 14:22 ` Oleksij Rempel
-1 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, Robin van der Gracht, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander, dri-devel
The backlight power is controlled through the reg_bl_12v0 regulator.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 9 ---------
1 file changed, 9 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 63ae2065834c..fe8df03c8bfb 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,14 +21,11 @@ memory@10000000 {
backlight_lcd: backlight-lcd {
compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_backlight>;
pwms = <&pwm1 0 500000>;
brightness-levels = <0 20 81 248 1000>;
default-brightness-level = <20>;
num-interpolated-steps = <21>;
power-supply = <®_bl_12v0>;
- enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
};
display {
@@ -367,12 +364,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
>;
};
- pinctrl_backlight: backlightgrp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
- >;
- };
-
pinctrl_can1phy: can1phy {
fsl,pins = <
/* CAN1_SR */
--
2.30.0
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 5/7] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, linux-arm-kernel
The backlight power is controlled through the reg_bl_12v0 regulator.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 9 ---------
1 file changed, 9 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 63ae2065834c..fe8df03c8bfb 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,14 +21,11 @@ memory@10000000 {
backlight_lcd: backlight-lcd {
compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_backlight>;
pwms = <&pwm1 0 500000>;
brightness-levels = <0 20 81 248 1000>;
default-brightness-level = <20>;
num-interpolated-steps = <21>;
power-supply = <®_bl_12v0>;
- enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
};
display {
@@ -367,12 +364,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
>;
};
- pinctrl_backlight: backlightgrp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
- >;
- };
-
pinctrl_can1phy: can1phy {
fsl,pins = <
/* CAN1_SR */
--
2.30.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 5/7] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Fabio Estevam, linux-arm-kernel
The backlight power is controlled through the reg_bl_12v0 regulator.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 9 ---------
1 file changed, 9 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 63ae2065834c..fe8df03c8bfb 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,14 +21,11 @@ memory@10000000 {
backlight_lcd: backlight-lcd {
compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_backlight>;
pwms = <&pwm1 0 500000>;
brightness-levels = <0 20 81 248 1000>;
default-brightness-level = <20>;
num-interpolated-steps = <21>;
power-supply = <®_bl_12v0>;
- enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
};
display {
@@ -367,12 +364,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
>;
};
- pinctrl_backlight: backlightgrp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
- >;
- };
-
pinctrl_can1phy: can1phy {
fsl,pins = <
/* CAN1_SR */
--
2.30.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
2021-01-20 14:22 ` Oleksij Rempel
(?)
@ 2021-01-20 14:22 ` Oleksij Rempel
-1 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Robin van der Gracht, dri-devel
At some point PWM cell count was changed, but it didn't triggered any
error, since this DT was overwriting "#pwm-cells".
To make sure, we are in sync with the kernel driver, remove this
property and fix the pwm consumer.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index fe8df03c8bfb..35d06ba93c88 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,7 +21,7 @@ memory@10000000 {
backlight_lcd: backlight-lcd {
compatible = "pwm-backlight";
- pwms = <&pwm1 0 500000>;
+ pwms = <&pwm1 0 500000 0>;
brightness-levels = <0 20 81 248 1000>;
default-brightness-level = <20>;
num-interpolated-steps = <21>;
@@ -325,7 +325,6 @@ &ipu1_di0_disp0 {
};
&pwm1 {
- #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
--
2.30.0
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, linux-arm-kernel
At some point PWM cell count was changed, but it didn't triggered any
error, since this DT was overwriting "#pwm-cells".
To make sure, we are in sync with the kernel driver, remove this
property and fix the pwm consumer.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index fe8df03c8bfb..35d06ba93c88 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,7 +21,7 @@ memory@10000000 {
backlight_lcd: backlight-lcd {
compatible = "pwm-backlight";
- pwms = <&pwm1 0 500000>;
+ pwms = <&pwm1 0 500000 0>;
brightness-levels = <0 20 81 248 1000>;
default-brightness-level = <20>;
num-interpolated-steps = <21>;
@@ -325,7 +325,6 @@ &ipu1_di0_disp0 {
};
&pwm1 {
- #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
--
2.30.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Fabio Estevam, linux-arm-kernel
At some point PWM cell count was changed, but it didn't triggered any
error, since this DT was overwriting "#pwm-cells".
To make sure, we are in sync with the kernel driver, remove this
property and fix the pwm consumer.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index fe8df03c8bfb..35d06ba93c88 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,7 +21,7 @@ memory@10000000 {
backlight_lcd: backlight-lcd {
compatible = "pwm-backlight";
- pwms = <&pwm1 0 500000>;
+ pwms = <&pwm1 0 500000 0>;
brightness-levels = <0 20 81 248 1000>;
default-brightness-level = <20>;
num-interpolated-steps = <21>;
@@ -325,7 +325,6 @@ &ipu1_di0_disp0 {
};
&pwm1 {
- #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
--
2.30.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 7/7] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties
2021-01-20 14:22 ` Oleksij Rempel
(?)
@ 2021-01-20 14:22 ` Oleksij Rempel
-1 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Robin van der Gracht, dri-devel
Remove touchscreen-size-* properties. This values are not correct, event if it
works with ts_test tool, it fails to work properly with weston.
And the real range of values reported by the driver (or measured by the
controller) is close to max values and may change with time on resistive
panels. So, it make no sense to keep this values in the device tree.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-plym2m.dts | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 4d0d3d3386af..c97274f0df07 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -138,8 +138,6 @@ touchscreen@0 {
interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
- touchscreen-size-x = <800>;
- touchscreen-size-y = <480>;
touchscreen-inverted-x;
touchscreen-inverted-y;
touchscreen-max-pressure = <4095>;
--
2.30.0
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 7/7] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, linux-arm-kernel
Remove touchscreen-size-* properties. This values are not correct, event if it
works with ts_test tool, it fails to work properly with weston.
And the real range of values reported by the driver (or measured by the
controller) is close to max values and may change with time on resistive
panels. So, it make no sense to keep this values in the device tree.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-plym2m.dts | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 4d0d3d3386af..c97274f0df07 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -138,8 +138,6 @@ touchscreen@0 {
interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
- touchscreen-size-x = <800>;
- touchscreen-size-y = <480>;
touchscreen-inverted-x;
touchscreen-inverted-y;
touchscreen-max-pressure = <4095>;
--
2.30.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v1 7/7] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties
@ 2021-01-20 14:22 ` Oleksij Rempel
0 siblings, 0 replies; 27+ messages in thread
From: Oleksij Rempel @ 2021-01-20 14:22 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Robin van der Gracht, linux-kernel, dri-devel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Fabio Estevam, linux-arm-kernel
Remove touchscreen-size-* properties. This values are not correct, event if it
works with ts_test tool, it fails to work properly with weston.
And the real range of values reported by the driver (or measured by the
controller) is close to max values and may change with time on resistive
panels. So, it make no sense to keep this values in the device tree.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-plym2m.dts | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 4d0d3d3386af..c97274f0df07 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -138,8 +138,6 @@ touchscreen@0 {
interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
- touchscreen-size-x = <800>;
- touchscreen-size-y = <480>;
touchscreen-inverted-x;
touchscreen-inverted-y;
touchscreen-max-pressure = <4095>;
--
2.30.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 27+ messages in thread