* [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1
@ 2021-09-20 8:40 Vyacheslav Bocharov
2021-09-20 8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov
` (3 more replies)
0 siblings, 4 replies; 6+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-20 8:40 UTC (permalink / raw)
To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic
Add support for new home automation devices manufactured by JetHome.
Patches prepared for use with the "ARM: meson: Sync Amlogic DT from Linux 5.14" patch series by Neil Armstrong
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console
Changes from v2:
- fix "Alignment should match open parenthesis" in board/amlogic/jethub-j80/jethub-j80.c
- add missing files to board/amlogic/jethub-j80/MAINTAINERS
- fix unexpected unindent in doc files
Changes from v1:
- fix BOOT_TARGET_DEVICES in jethub.h (patch 1/3)
- add lore URLs to description (patch 2/3)
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Vyacheslav Bocharov (3):
ARM: amlogic: add JetHub common config header
ARM: amlogic: add JetHub D1/H1 device support
ARM: amlogic: add JetHub D1/H1 docs
arch/arm/dts/Makefile | 2 +
.../arm/dts/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++
.../meson-gxl-s905w-jethome-jethub-j80.dts | 241 ++++++++++++
board/amlogic/jethub-j80/MAINTAINERS | 9 +
board/amlogic/jethub-j80/Makefile | 6 +
board/amlogic/jethub-j80/jethub-j80.c | 68 ++++
configs/jethub_j100_defconfig | 55 +++
configs/jethub_j80_defconfig | 63 +++
doc/board/amlogic/index.rst | 128 ++++---
doc/board/amlogic/jethub-j100.rst | 108 ++++++
doc/board/amlogic/jethub-j80.rst | 97 +++++
include/configs/jethub.h | 40 ++
12 files changed, 1115 insertions(+), 63 deletions(-)
create mode 100644 arch/arm/dts/meson-axg-jethome-jethub-j100.dts
create mode 100644 arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts
create mode 100644 board/amlogic/jethub-j80/MAINTAINERS
create mode 100644 board/amlogic/jethub-j80/Makefile
create mode 100644 board/amlogic/jethub-j80/jethub-j80.c
create mode 100644 configs/jethub_j100_defconfig
create mode 100644 configs/jethub_j80_defconfig
create mode 100644 doc/board/amlogic/jethub-j100.rst
create mode 100644 doc/board/amlogic/jethub-j80.rst
create mode 100644 include/configs/jethub.h
--
2.30.2
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 1/3] ARM: amlogic: add JetHub common config header
2021-09-20 8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov
@ 2021-09-20 8:40 ` Vyacheslav Bocharov
2021-09-20 12:30 ` Neil Armstrong
2021-09-20 8:40 ` [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support Vyacheslav Bocharov
` (2 subsequent siblings)
3 siblings, 1 reply; 6+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-20 8:40 UTC (permalink / raw)
To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic
JetHub devices uses its own boot sequence with "rescue" button
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
include/configs/jethub.h | 40 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 40 insertions(+)
create mode 100644 include/configs/jethub.h
diff --git a/include/configs/jethub.h b/include/configs/jethub.h
new file mode 100644
index 0000000000..35f85095ac
--- /dev/null
+++ b/include/configs/jethub.h
@@ -0,0 +1,40 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration for JetHome devices
+ * Copyright (C) 2021 Vyacheslav Bocharov
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+#ifndef __JETHUB_CONFIG_H
+#define __JETHUB_CONFIG_H
+
+#if defined(CONFIG_MESON_AXG)
+#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \
+ "bootcmd_rescue=" \
+ "if gpio input 10; then " \
+ "run bootcmd_usb0;" \
+ "fi;\0"
+#else
+#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \
+ "bootcmd_rescue=" \
+ "if test \"${userbutton}\" = \"true\"; then " \
+ "run bootcmd_mmc0; " \
+ "fi;\0"
+#endif
+
+#define BOOTENV_DEV_NAME_RESCUE(devtypeu, devtypel, instance) \
+ "rescue "
+
+#ifndef BOOT_TARGET_DEVICES
+#define BOOT_TARGET_DEVICES(func) \
+ func(RESCUE, rescue, na) \
+ func(MMC, mmc, 1) \
+ func(MMC, mmc, 0) \
+ BOOT_TARGET_DEVICES_USB(func) \
+ func(PXE, pxe, na) \
+ func(DHCP, dhcp, na)
+#endif
+
+#include <configs/meson64.h>
+
+#endif /* __JETHUB_CONFIG_H */
--
2.30.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support
2021-09-20 8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov
2021-09-20 8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov
@ 2021-09-20 8:40 ` Vyacheslav Bocharov
2021-09-20 8:40 ` [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs Vyacheslav Bocharov
2021-09-21 7:27 ` [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Neil Armstrong
3 siblings, 0 replies; 6+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-20 8:40 UTC (permalink / raw)
To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic
Add support for new home automation devices.
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console
Patches from:
- JetHub H1
https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.in
https://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
- JetHub D1
https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.in
https://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm/dts/Makefile | 2 +
.../arm/dts/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++
.../meson-gxl-s905w-jethome-jethub-j80.dts | 241 ++++++++++++
board/amlogic/jethub-j80/MAINTAINERS | 9 +
board/amlogic/jethub-j80/Makefile | 6 +
board/amlogic/jethub-j80/jethub-j80.c | 68 ++++
configs/jethub_j100_defconfig | 55 +++
configs/jethub_j80_defconfig | 63 +++
8 files changed, 805 insertions(+)
create mode 100644 arch/arm/dts/meson-axg-jethome-jethub-j100.dts
create mode 100644 arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts
create mode 100644 board/amlogic/jethub-j80/MAINTAINERS
create mode 100644 board/amlogic/jethub-j80/Makefile
create mode 100644 board/amlogic/jethub-j80/jethub-j80.c
create mode 100644 configs/jethub_j100_defconfig
create mode 100644 configs/jethub_j80_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index f0160d2dc0..d1893a9812 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -169,10 +169,12 @@ dtb-$(CONFIG_ARCH_MESON) += \
meson-gxl-s905x-libretech-cc-v2.dtb \
meson-gxl-s905x-khadas-vim.dtb \
meson-gxl-s905d-libretech-pc.dtb \
+ meson-gxl-s905w-jethome-jethub-j80.dtb \
meson-gxm-khadas-vim2.dtb \
meson-gxm-s912-libretech-pc.dtb \
meson-gxm-wetek-core2.dtb \
meson-axg-s400.dtb \
+ meson-axg-jethome-jethub-j100.dtb \
meson-g12a-u200.dtb \
meson-g12a-sei510.dtb \
meson-g12b-gtking.dtb \
diff --git a/arch/arm/dts/meson-axg-jethome-jethub-j100.dts b/arch/arm/dts/meson-axg-jethome-jethub-j100.dts
new file mode 100644
index 0000000000..5783732dc6
--- /dev/null
+++ b/arch/arm/dts/meson-axg-jethome-jethub-j100.dts
@@ -0,0 +1,361 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
+ model = "JetHome JetHub J100";
+ aliases {
+ serial0 = &uart_AO; /* Console */
+ serial1 = &uart_AO_B; /* External UART (Wireless Module) */
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ /* 1024MB RAM */
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ reserved-memory {
+ linux,cma {
+ size = <0x0 0x400000>;
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ usb_pwr: regulator-usb_pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&scpi_sensors 0>;
+ trips {
+ cpu_passive: cpu-passive {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ cpu_hot: cpu-hot {
+ temperature = <80000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "hot";
+ };
+
+ cpu_critical: cpu-critical {
+ temperature = <100000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+ };
+
+ cpu_cooling_maps: cooling-maps {
+ map0 {
+ trip = <&cpu_passive>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ onewire {
+ compatible = "w1-gpio";
+ gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>;
+ #gpio-cells = <1>;
+ };
+};
+
+&efuse {
+ sn: sn@32 {
+ reg = <0x32 0x20>;
+ };
+
+ eth_mac: eth_mac@0 {
+ reg = <0x0 0x6>;
+ };
+
+ bt_mac: bt_mac@6 {
+ reg = <0x6 0x6>;
+ };
+
+ wifi_mac: wifi_mac@c {
+ reg = <0xc 0x6>;
+ };
+
+ bid: bid@12 {
+ reg = <0x12 0x20>;
+ };
+};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_rmii_x_pins>;
+ pinctrl-names = "default";
+ phy-handle = <ð_phy0>;
+ phy-mode = "rmii";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+ eth_phy0: ethernet-phy@0 {
+ /* compatible = "ethernet-phy-id0243.0c54";*/
+ max-speed = <100>;
+ reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <10000>;
+ reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+ status = "okay";
+ pinctrl-0 = <&i2c1_z_pins>;
+ pinctrl-names = "default";
+
+ /* RTC */
+ pcf8563: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ status = "okay";
+ };
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+ status = "okay";
+ pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_ab {
+ status = "okay";
+ pinctrl-0 = <&pwm_a_x20_pins>;
+ pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr104;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* emmc storage */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+ status = "okay";
+ pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* UART Console */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_b_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+ status = "okay";
+ pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
+ pinctrl-names = "default";
+};
+
+&gpio {
+ gpio-line-names =
+ "", "", "", "", "", // 0 - 4
+ "", "", "", "", "", // 5 - 9
+ "UserButton", "", "", "", "", // 10 - 14
+ "", "", "", "", "", // 15 - 19
+ "", "", "", "", "", // 20 - 24
+ "", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
+ "Output1", "", "", "", "", // 30 - 34
+ "", "ZigBeeBOOT", "", "", "", // 35 - 39
+ "", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+ "Input2", "Input1", "", "", "", // 45 - 49
+ "", "", "", "", "", // 50 - 54
+ "", "", "", "", "", // 55 - 59
+ "", "", "", "", "", // 60 - 64
+ "", "", "", "", "", // 65 - 69
+ "", "", "", "", "", // 70 - 74
+ "", "", "", "", "", // 75 - 79
+ "", "", "", "", "", // 80 - 84
+ "", ""; // 85-86
+};
+
+&cpu0 {
+ #cooling-cells = <2>;
+};
+
+&cpu1 {
+ #cooling-cells = <2>;
+};
+
+&cpu2 {
+ #cooling-cells = <2>;
+};
+
+&cpu3 {
+ #cooling-cells = <2>;
+};
diff --git a/arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts b/arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts
new file mode 100644
index 0000000000..6eafb90869
--- /dev/null
+++ b/arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl.dtsi"
+
+/ {
+ compatible = "jethome,jethub-j80", "amlogic,s905w", "amlogic,meson-gxl";
+ model = "JetHome JetHub J80";
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ reserved-memory {
+ linux,cma {
+ size = <0x0 0x1000000>;
+ };
+ };
+
+ aliases {
+ serial0 = &uart_AO; /* Console */
+ serial1 = &uart_A; /* Bluetooth */
+ serial2 = &uart_AO_B; /* Wireless module 1 */
+ serial3 = &uart_C; /* Wireless module 2 */
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+};
+
+&efuse {
+ bt_mac: bt_mac@6 {
+ reg = <0x6 0x6>;
+ };
+
+ wifi_mac: wifi_mac@C {
+ reg = <0xc 0x6>;
+ };
+};
+
+&sn {
+ reg = <0x32 0x20>;
+};
+
+ð_mac {
+ reg = <0x0 0x6>;
+};
+
+&bid {
+ reg = <0x12 0x20>;
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+
+ non-removable;
+ disable-wp;
+
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* Console UART */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* S905W only has access to its internal PHY */
+ðmac {
+ status = "okay";
+ phy-mode = "rmii";
+ phy-handle = <&internal_phy>;
+};
+
+&internal_phy {
+ status = "okay";
+ pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>;
+ pinctrl-names = "default";
+};
+
+&uart_A {
+ status = "okay";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+};
+
+&uart_C {
+ status = "okay";
+ pinctrl-0 = <&uart_c_pins>;
+ pinctrl-names = "default";
+};
+
+&uart_AO_B {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_b_pins>, <&uart_ao_b_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+};
+
+&i2c_B {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_b_pins>;
+
+ pcf8563: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ status = "okay";
+ };
+};
diff --git a/board/amlogic/jethub-j80/MAINTAINERS b/board/amlogic/jethub-j80/MAINTAINERS
new file mode 100644
index 0000000000..459e9f89da
--- /dev/null
+++ b/board/amlogic/jethub-j80/MAINTAINERS
@@ -0,0 +1,9 @@
+JetHome JetHub
+M: Vyacheslav Bocharov <adeep@lexina.in>
+S: Maintained
+L: u-boot-amlogic@groups.io
+F: board/amlogic/jethub-j80/
+F: configs/jethub_j80_defconfig
+F: configs/jethub_j100_defconfig
+F: doc/board/amlogic/jethub-j80.rst
+F: doc/board/amlogic/jethub-j100.rst
diff --git a/board/amlogic/jethub-j80/Makefile b/board/amlogic/jethub-j80/Makefile
new file mode 100644
index 0000000000..a727a4b222
--- /dev/null
+++ b/board/amlogic/jethub-j80/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2021 Vyacheslav Bocharov
+# Author: Vyacheslav Bocharov <adeep@lexina.in>
+
+obj-y := jethub-j80.o
diff --git a/board/amlogic/jethub-j80/jethub-j80.c b/board/amlogic/jethub-j80/jethub-j80.c
new file mode 100644
index 0000000000..ae402303aa
--- /dev/null
+++ b/board/amlogic/jethub-j80/jethub-j80.c
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2021 Vyacheslav Bocharov
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <adc.h>
+#include <env.h>
+#include <init.h>
+#include <net.h>
+#include <asm/io.h>
+#include <asm/arch/gx.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+#include <asm/arch/mem.h>
+
+#define EFUSE_SN_OFFSET 50
+#define EFUSE_SN_SIZE 32
+#define EFUSE_MAC_OFFSET 0
+#define EFUSE_MAC_SIZE 6
+#define EFUSE_USID_OFFSET 18
+#define EFUSE_USID_SIZE 32
+
+int misc_init_r(void)
+{
+ u8 mac_addr[EFUSE_MAC_SIZE];
+ char serial[EFUSE_SN_SIZE];
+ char usid[EFUSE_USID_SIZE];
+ ssize_t len;
+ unsigned int adcval;
+ int ret;
+ char value[16];
+
+ if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
+ len = meson_sm_read_efuse(EFUSE_MAC_OFFSET,
+ mac_addr, EFUSE_MAC_SIZE);
+ if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr))
+ eth_env_set_enetaddr("ethaddr", mac_addr);
+ else
+ meson_generate_serial_ethaddr();
+ }
+
+ if (!env_get("serial")) {
+ len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
+ EFUSE_SN_SIZE);
+ if (len == EFUSE_SN_SIZE)
+ env_set("serial", serial);
+ }
+
+ if (!env_get("usid")) {
+ len = meson_sm_read_efuse(EFUSE_USID_OFFSET, usid,
+ EFUSE_USID_SIZE);
+ if (len == EFUSE_USID_SIZE)
+ env_set("usid", usid);
+ }
+
+ ret = adc_channel_single_shot("adc@8680", 0, &adcval);
+ if (adcval < 3000)
+ env_set("userbutton", "true");
+ else
+ env_set("userbutton", "false");
+
+ return 0;
+}
diff --git a/configs/jethub_j100_defconfig b/configs/jethub_j100_defconfig
new file mode 100644
index 0000000000..290ce4db85
--- /dev/null
+++ b/configs/jethub_j100_defconfig
@@ -0,0 +1,55 @@
+CONFIG_ARM=y
+CONFIG_SYS_CONFIG_NAME="jethub"
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x2000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-axg-jethome-jethub-j100"
+CONFIG_MESON_AXG=y
+CONFIG_DEBUG_UART_BASE=0xff803000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" jethubj100"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_MISC_INIT_R=y
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+CONFIG_RANDOM_UUID=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_MTD_UBI=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE_MESON8B=y
+CONFIG_MESON_GXL_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_AXG=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_DWC3_MESON_GXL=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/configs/jethub_j80_defconfig b/configs/jethub_j80_defconfig
new file mode 100644
index 0000000000..7db05af3b0
--- /dev/null
+++ b/configs/jethub_j80_defconfig
@@ -0,0 +1,63 @@
+CONFIG_ARM=y
+CONFIG_SYS_BOARD="jethub-j80"
+CONFIG_SYS_CONFIG_NAME="jethub"
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x2000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-gxl-s905w-jethome-jethub-j80"
+CONFIG_MESON_GXL=y
+CONFIG_DEBUG_UART_BASE=0xc81004c0
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" jethubj80"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_CONSOLE_MUX=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_MISC_INIT_R=y
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_ADC=y
+CONFIG_CMD_GPIO=y
+CONFIG_RANDOM_UUID=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SARADC_MESON=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_MTD_UBI=y
+CONFIG_PHY_MESON_GXL=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_DM_MDIO_MUX=y
+CONFIG_ETH_DESIGNWARE_MESON8B=y
+CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MESON_GXL_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_GXL=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_DWC3_MESON_GXL=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_OF_LIBFDT_OVERLAY=y
--
2.30.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs
2021-09-20 8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov
2021-09-20 8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov
2021-09-20 8:40 ` [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support Vyacheslav Bocharov
@ 2021-09-20 8:40 ` Vyacheslav Bocharov
2021-09-21 7:27 ` [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Neil Armstrong
3 siblings, 0 replies; 6+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-20 8:40 UTC (permalink / raw)
To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic
Fix doc/board/amlogic/index.rst:
- Add S905W to S905X column.
- Add JetHub devices to the corresponding columns.
- Fix tabs to spaces for table alignment
Add doc/board/amlogic files:
- jethub-j100.rst
- jethub-j80.rst
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
---
doc/board/amlogic/index.rst | 128 +++++++++++++++---------------
doc/board/amlogic/jethub-j100.rst | 108 +++++++++++++++++++++++++
doc/board/amlogic/jethub-j80.rst | 97 ++++++++++++++++++++++
3 files changed, 270 insertions(+), 63 deletions(-)
create mode 100644 doc/board/amlogic/jethub-j100.rst
create mode 100644 doc/board/amlogic/jethub-j80.rst
diff --git a/doc/board/amlogic/index.rst b/doc/board/amlogic/index.rst
index 2913ab281a..c18f1b7e71 100644
--- a/doc/board/amlogic/index.rst
+++ b/doc/board/amlogic/index.rst
@@ -10,69 +10,69 @@ An up-do-date matrix is also available on: http://linux-meson.com
This matrix concerns the actual source code version.
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| | S905 | S905X | S912 | A113X | S905X2 | S922X | S905X3 |
-| | | S805X | S905D | | S905D2 | A311D | S905D3 |
-| | | | | | S905Y2 | | |
-+===============================+===========+=================+==============+============+============+=============+==============+
-| Boards | Odroid-C2 | P212 | Khadas VIM2 | S400 | U200 | Odroid-N2 | SEI610 |
-| | Nanopi-K2 | Khadas-VIM | Libretech-PC | | SEI510 | Khadas-VIM3 | Khadas-VIM3L |
-| | P200 | LibreTech-CC v1 | WeTek Core2 | | | GT-King/Pro | Odroid-C4 |
-| | P201 | LibreTech-AC v2 | | | | GSKing-X | Odroid-HC4 |
-| | | | | | | | BananaPi-M5 |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| UART | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Pinctrl/GPIO | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Clock Control | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| PWM | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Reset Control | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Infrared Decoder | No | No | No | No | No | No | No |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Ethernet | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Multi-core | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Fuse access | **Yes** | **Yes** |**Yes** |**Yes** |**Yes** |**Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| SPI (FC) | **Yes** | **Yes** | **Yes** | **Yes** |**Yes** | **Yes** | No |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| SPI (CC) | No | No | No | No | No | No | No |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| I2C | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| USB | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| USB OTG | No | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| eMMC | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| SDCard | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| NAND | No | No | No | No | No | No | No |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| ADC | **Yes** | **Yes** | **Yes** | No | No | No | No |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| CVBS Output | **Yes** | **Yes** | **Yes** | *N/A* | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| HDMI Output | **Yes** | **Yes** | **Yes** | *N/A* | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| CEC | No | No | No | *N/A* | No | No | No |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Thermal Sensor | No | No | No | No | No | No | No |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| LCD/LVDS Output | No | *N/A* | No | No | No | No | No |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| MIPI DSI Output | *N/A* | *N/A* | *N/A* | No | No | No | No |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| SoC (version) information | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| PCIe (+NVMe) | *N/A* | *N/A* | *N/A* | **Yes** | **Yes** | **Yes** | **Yes** |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| | S905 | S905X | S912 | A113X | S905X2 | S922X | S905X3 |
+| | | S805X | S905D | | S905D2 | A311D | S905D3 |
+| | | S905W | | | S905Y2 | | |
++===============================+===========+=================+==============+=============+============+=============+==============+
+| Boards | Odroid-C2 | P212 | Khadas VIM2 | S400 | U200 | Odroid-N2 | SEI610 |
+| | Nanopi-K2 | Khadas-VIM | Libretech-PC | JetHub J100 | SEI510 | Khadas-VIM3 | Khadas-VIM3L |
+| | P200 | LibreTech-CC v1 | WeTek Core2 | | | GT-King/Pro | Odroid-C4 |
+| | P201 | LibreTech-AC v2 | | | | GSKing-X | Odroid-HC4 |
+| | | JetHub J80 | | | | | BananaPi-M5 |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| UART | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Pinctrl/GPIO | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Clock Control | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| PWM | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Reset Control | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Infrared Decoder | No | No | No | No | No | No | No |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Ethernet | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Multi-core | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Fuse access | **Yes** | **Yes** |**Yes** |**Yes** |**Yes** |**Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| SPI (FC) | **Yes** | **Yes** | **Yes** | **Yes** |**Yes** | **Yes** | No |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| SPI (CC) | No | No | No | No | No | No | No |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| I2C | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| USB | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| USB OTG | No | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| eMMC | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| SDCard | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| NAND | No | No | No | No | No | No | No |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| ADC | **Yes** | **Yes** | **Yes** | No | No | No | No |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| CVBS Output | **Yes** | **Yes** | **Yes** | *N/A* | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| HDMI Output | **Yes** | **Yes** | **Yes** | *N/A* | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| CEC | No | No | No | *N/A* | No | No | No |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Thermal Sensor | No | No | No | No | No | No | No |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| LCD/LVDS Output | No | *N/A* | No | No | No | No | No |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| MIPI DSI Output | *N/A* | *N/A* | *N/A* | No | No | No | No |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| SoC (version) information | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| PCIe (+NVMe) | *N/A* | *N/A* | *N/A* | **Yes** | **Yes** | **Yes** | **Yes** |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
Board Documentation
-------------------
@@ -82,6 +82,8 @@ Board Documentation
beelink-gtking
beelink-gtkingpro
+ jethub-j100
+ jethub-j80
khadas-vim2
khadas-vim3l
khadas-vim3
diff --git a/doc/board/amlogic/jethub-j100.rst b/doc/board/amlogic/jethub-j100.rst
new file mode 100644
index 0000000000..58602787d3
--- /dev/null
+++ b/doc/board/amlogic/jethub-j100.rst
@@ -0,0 +1,108 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+U-Boot for JetHub J100
+=======================
+
+JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
+controller manufactured by JetHome with the following specifications:
+
+ - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
+ - no video out
+ - 512Mb/1GB DDR3
+ - 8/16GB eMMC flash
+ - 1 x USB 2.0
+ - 1 x 10/100Mbps ethernet
+ - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE
+ 802.11a/b/g/n/ac, Bluetooth 4.2.
+ - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output
+ power and Zigbee 3.0 support.
+ - 2 x gpio LEDS
+ - GPIO user Button
+ - 1 x 1-Wire
+ - 2 x RS-485
+ - 4 x dry contact digital GPIO inputs
+ - 3 x relay GPIO outputs
+ - DC source with a voltage of 9 to 56 V / Passive POE
+ - DIN Rail Mounting case
+
+U-Boot compilation
+------------------
+
+.. code-block:: bash
+
+ $ export CROSS_COMPILE=aarch64-none-elf-
+ $ make jethub_j100_defconfig
+ $ make
+
+Image creation
+--------------
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain binaries
+from the git tree published by the board vendor:
+
+.. code-block:: bash
+
+ $ git clone https://github.com/jethome-ru/jethub-aml-tools jethub-u-boot
+ $ cd jethub-u-boot
+ $ export FIPDIR=$PWD
+
+Go back to mainline U-boot source tree then :
+
+.. code-block:: bash
+
+ $ mkdir fip
+
+ $ cp $FIPDIR/j100/bl2.bin fip/
+ $ cp $FIPDIR/j100/acs.bin fip/
+ $ cp $FIPDIR/j100/bl21.bin fip/
+ $ cp $FIPDIR/j100/bl30.bin fip/
+ $ cp $FIPDIR/j100/bl301.bin fip/
+ $ cp $FIPDIR/j100/bl31.img fip/
+ $ cp u-boot.bin fip/bl33.bin
+
+ $ $FIPDIR/blx_fix.sh \
+ fip/bl30.bin \
+ fip/zero_tmp \
+ fip/bl30_zero.bin \
+ fip/bl301.bin \
+ fip/bl301_zero.bin \
+ fip/bl30_new.bin \
+ bl30
+
+ $ $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ $ $FIPDIR/blx_fix.sh \
+ fip/bl2_acs.bin \
+ fip/zero_tmp \
+ fip/bl2_zero.bin \
+ fip/bl21.bin \
+ fip/bl21_zero.bin \
+ fip/bl2_new.bin \
+ bl2
+
+ $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl30_new.bin \
+ --output fip/bl30_new.bin.enc \
+ --level v3 --type bl30
+ $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl31.img \
+ --output fip/bl31.img.enc \
+ --level v3 --type bl31
+ $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl33.bin --compress lz4 \
+ --output fip/bl33.bin.enc \
+ --level v3 --type bl33
+ $ $FIPDIR/j100/aml_encrypt_axg --bl2sig --input fip/bl2_new.bin \
+ --output fip/bl2.n.bin.sig
+ $ $FIPDIR/j100/aml_encrypt_axg --bootmk \
+ --output fip/u-boot.bin \
+ --bl2 fip/bl2.n.bin.sig \
+ --bl30 fip/bl30_new.bin.enc \
+ --bl31 fip/bl31.img.enc \
+ --bl33 fip/bl33.bin.enc --level v3
+
+and then write the image to eMMC with:
+
+.. code-block:: bash
+
+ $ DEV=/dev/your_emmc_device
+ $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
diff --git a/doc/board/amlogic/jethub-j80.rst b/doc/board/amlogic/jethub-j80.rst
new file mode 100644
index 0000000000..6b7bdc78b1
--- /dev/null
+++ b/doc/board/amlogic/jethub-j80.rst
@@ -0,0 +1,97 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+U-Boot for JetHub J80
+======================
+
+JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation
+controller manufactured by JetHome with the following specifications:
+
+ - Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
+ - No video out
+ - 1GB DDR3
+ - 8/16GB eMMC flash
+ - 2 x USB 2.0
+ - 1 x 10/100Mbps ethernet
+ - SDIO WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
+ - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output
+ power and Zigbee 3.0 support.
+ - MicroSD 2.x/3.x/4.x DS/HS cards.
+ - 1 x gpio LED
+ - ADC user Button
+ - DC source 5V microUSB
+ - Square plastic case
+
+U-Boot compilation
+------------------
+
+.. code-block:: bash
+
+ $ export CROSS_COMPILE=aarch64-none-elf-
+ $ make jethub_j80_defconfig
+ $ make
+
+Image creation
+--------------
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain binaries
+from the git tree published by the board vendor:
+
+.. code-block:: bash
+
+ $ git clone https://github.com/jethome-ru/jethub-aml-tools jethub-u-boot
+ $ cd jethub-u-boot
+ $ export FIPDIR=$PWD
+
+Go back to mainline U-Boot source tree then :
+
+.. code-block:: bash
+
+ $ mkdir fip
+
+ $ cp $FIPDIR/j80/bl2.bin fip/
+ $ cp $FIPDIR/j80/acs.bin fip/
+ $ cp $FIPDIR/j80/bl21.bin fip/
+ $ cp $FIPDIR/j80/bl30.bin fip/
+ $ cp $FIPDIR/j80/bl301.bin fip/
+ $ cp $FIPDIR/j80/bl31.img fip/
+ $ cp u-boot.bin fip/bl33.bin
+
+ $ $FIPDIR/blx_fix.sh \
+ fip/bl30.bin \
+ fip/zero_tmp \
+ fip/bl30_zero.bin \
+ fip/bl301.bin \
+ fip/bl301_zero.bin \
+ fip/bl30_new.bin \
+ bl30
+
+ $ python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ $ $FIPDIR/blx_fix.sh \
+ fip/bl2_acs.bin \
+ fip/zero_tmp \
+ fip/bl2_zero.bin \
+ fip/bl21.bin \
+ fip/bl21_zero.bin \
+ fip/bl2_new.bin \
+ bl2
+
+ $ $FIPDIR/j80/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
+ $ $FIPDIR/j80/aml_encrypt_gxl --bl3enc --input fip/bl31.img
+ $ $FIPDIR/j80/aml_encrypt_gxl --bl3enc --input fip/bl33.bin --compress lz4
+ $ $FIPDIR/j80/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
+ $ $FIPDIR/j80/aml_encrypt_gxl --bootmk \
+ --output fip/u-boot.bin \
+ --bl2 fip/bl2.n.bin.sig \
+ --bl30 fip/bl30_new.bin.enc \
+ --bl31 fip/bl31.img.enc \
+ --bl33 fip/bl33.bin.enc
+
+and then write the image to SD/eMMC with:
+
+.. code-block:: bash
+
+ $ DEV=/dev/your_sd_device
+ $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
--
2.30.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v3 1/3] ARM: amlogic: add JetHub common config header
2021-09-20 8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov
@ 2021-09-20 12:30 ` Neil Armstrong
0 siblings, 0 replies; 6+ messages in thread
From: Neil Armstrong @ 2021-09-20 12:30 UTC (permalink / raw)
To: Vyacheslav Bocharov; +Cc: u-boot, u-boot-amlogic
On 20/09/2021 10:40, Vyacheslav Bocharov wrote:
> JetHub devices uses its own boot sequence with "rescue" button
>
> Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
> ---
> include/configs/jethub.h | 40 ++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 40 insertions(+)
> create mode 100644 include/configs/jethub.h
>
> diff --git a/include/configs/jethub.h b/include/configs/jethub.h
> new file mode 100644
> index 0000000000..35f85095ac
> --- /dev/null
> +++ b/include/configs/jethub.h
> @@ -0,0 +1,40 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Configuration for JetHome devices
> + * Copyright (C) 2021 Vyacheslav Bocharov
> + * Author: Vyacheslav Bocharov <adeep@lexina.in>
> + */
> +
> +#ifndef __JETHUB_CONFIG_H
> +#define __JETHUB_CONFIG_H
> +
> +#if defined(CONFIG_MESON_AXG)
> +#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \
> + "bootcmd_rescue=" \
> + "if gpio input 10; then " \
> + "run bootcmd_usb0;" \
> + "fi;\0"
> +#else
> +#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \
> + "bootcmd_rescue=" \
> + "if test \"${userbutton}\" = \"true\"; then " \
> + "run bootcmd_mmc0; " \
> + "fi;\0"
> +#endif
> +
> +#define BOOTENV_DEV_NAME_RESCUE(devtypeu, devtypel, instance) \
> + "rescue "
> +
> +#ifndef BOOT_TARGET_DEVICES
> +#define BOOT_TARGET_DEVICES(func) \
> + func(RESCUE, rescue, na) \
> + func(MMC, mmc, 1) \
> + func(MMC, mmc, 0) \
> + BOOT_TARGET_DEVICES_USB(func) \
> + func(PXE, pxe, na) \
> + func(DHCP, dhcp, na)
> +#endif
> +
> +#include <configs/meson64.h>
> +
> +#endif /* __JETHUB_CONFIG_H */
>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1
2021-09-20 8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov
` (2 preceding siblings ...)
2021-09-20 8:40 ` [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs Vyacheslav Bocharov
@ 2021-09-21 7:27 ` Neil Armstrong
3 siblings, 0 replies; 6+ messages in thread
From: Neil Armstrong @ 2021-09-21 7:27 UTC (permalink / raw)
To: Vyacheslav Bocharov; +Cc: u-boot, u-boot-amlogic
On 20/09/2021 10:40, Vyacheslav Bocharov wrote:
> Add support for new home automation devices manufactured by JetHome.
> Patches prepared for use with the "ARM: meson: Sync Amlogic DT from Linux 5.14" patch series by Neil Armstrong
>
> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
> - DIN Rail Mounting case
> - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
> - no video out
> - 512Mb/1GB DDR3
> - 8/16GB eMMC flash
> - 1 x USB 2.0
> - 1 x 10/100Mbps ethernet
> - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
> - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
> - 2 x gpio LEDS
> - GPIO user Button
> - 1 x 1-Wire
> - 2 x RS-485
> - 4 x dry contact digital GPIO inputs
> - 3 x relay GPIO outputs
> - DC source with a voltage of 9 to 56 V / Passive POE
>
> JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
> - Square plastic case
> - Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
> - no video out
> - 1GB DDR3
> - 8/16GB eMMC flash
> - 2 x USB 2.0
> - 1 x 10/100Mbps ethernet
> - WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
> - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
> - MicroSD 2.x/3.x/4.x DS/HS cards.
> - 1 x gpio LED
> - ADC user Button
> - DC source 5V microUSB with serial console
>
> Changes from v2:
> - fix "Alignment should match open parenthesis" in board/amlogic/jethub-j80/jethub-j80.c
> - add missing files to board/amlogic/jethub-j80/MAINTAINERS
> - fix unexpected unindent in doc files
>
> Changes from v1:
> - fix BOOT_TARGET_DEVICES in jethub.h (patch 1/3)
> - add lore URLs to description (patch 2/3)
>
> Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
>
> Vyacheslav Bocharov (3):
> ARM: amlogic: add JetHub common config header
> ARM: amlogic: add JetHub D1/H1 device support
> ARM: amlogic: add JetHub D1/H1 docs
>
> arch/arm/dts/Makefile | 2 +
> .../arm/dts/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++
> .../meson-gxl-s905w-jethome-jethub-j80.dts | 241 ++++++++++++
> board/amlogic/jethub-j80/MAINTAINERS | 9 +
> board/amlogic/jethub-j80/Makefile | 6 +
> board/amlogic/jethub-j80/jethub-j80.c | 68 ++++
> configs/jethub_j100_defconfig | 55 +++
> configs/jethub_j80_defconfig | 63 +++
> doc/board/amlogic/index.rst | 128 ++++---
> doc/board/amlogic/jethub-j100.rst | 108 ++++++
> doc/board/amlogic/jethub-j80.rst | 97 +++++
> include/configs/jethub.h | 40 ++
> 12 files changed, 1115 insertions(+), 63 deletions(-)
> create mode 100644 arch/arm/dts/meson-axg-jethome-jethub-j100.dts
> create mode 100644 arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts
> create mode 100644 board/amlogic/jethub-j80/MAINTAINERS
> create mode 100644 board/amlogic/jethub-j80/Makefile
> create mode 100644 board/amlogic/jethub-j80/jethub-j80.c
> create mode 100644 configs/jethub_j100_defconfig
> create mode 100644 configs/jethub_j80_defconfig
> create mode 100644 doc/board/amlogic/jethub-j100.rst
> create mode 100644 doc/board/amlogic/jethub-j80.rst
> create mode 100644 include/configs/jethub.h
>
Applied to u-boot-amlogic-next
Neil
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2021-09-21 7:28 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-09-20 8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov
2021-09-20 8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov
2021-09-20 12:30 ` Neil Armstrong
2021-09-20 8:40 ` [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support Vyacheslav Bocharov
2021-09-20 8:40 ` [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs Vyacheslav Bocharov
2021-09-21 7:27 ` [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Neil Armstrong
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.