* [PATCH 0/4] PHYTEC i.MX 6UL/ULL devicetree patches
@ 2021-12-01 12:53 ` Andrej Picej
0 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-01 12:53 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, soc
Cc: robh+dt, kernel, shawnguo, leoyang.li, krzysztof.kozlowski,
linux, festevam, arnd, linux-imx, andrej.picej, y.bas
Hi all,
this patch series contains PHYTEC i.MX 6UL/ULL devicetree patches not
yet upstreamed.
First and second patch add devicetree for relatively new phyGATE
Tauri-S, which is based on i.MX 6ULL.
Third patch changes USB LDO voltage for i.MX 6UL/ULL phyCORE devices so
they match USB Full-speed compliance.
The fourth patch moves from using 2 pwm-cell to default 3 cell pwm
property.
Best regards,
Andrej
Alexander Bauer (1):
ARM: dts: imx6ull: Add support for PHYTEC phyGATE-Tauri-S with i.MX
6ULL
Andrej Picej (2):
dt-bindings: arm: fsl: add PHYTEC phyGATE Tauri i.MX6 ULL
ARM: dts: imx6ul: peb-av-02: move to 3 cell pwm
Yunus Bas (1):
ARM: dts: imx6ul: phycore: Change USB LDO voltage for usb compliance
.../devicetree/bindings/arm/fsl.yaml | 9 +
arch/arm/boot/dts/Makefile | 2 +
.../boot/dts/imx6ul-phytec-phycore-som.dtsi | 5 +
.../dts/imx6ul-phytec-segin-peb-av-02.dtsi | 3 +-
.../boot/dts/imx6ull-phytec-tauri-emmc.dts | 20 +
.../boot/dts/imx6ull-phytec-tauri-nand.dts | 20 +
arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi | 605 ++++++++++++++++++
7 files changed, 662 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi
--
2.25.1
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 0/4] PHYTEC i.MX 6UL/ULL devicetree patches
@ 2021-12-01 12:53 ` Andrej Picej
0 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-01 12:53 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, soc
Cc: robh+dt, kernel, shawnguo, leoyang.li, krzysztof.kozlowski,
linux, festevam, arnd, linux-imx, andrej.picej, y.bas
Hi all,
this patch series contains PHYTEC i.MX 6UL/ULL devicetree patches not
yet upstreamed.
First and second patch add devicetree for relatively new phyGATE
Tauri-S, which is based on i.MX 6ULL.
Third patch changes USB LDO voltage for i.MX 6UL/ULL phyCORE devices so
they match USB Full-speed compliance.
The fourth patch moves from using 2 pwm-cell to default 3 cell pwm
property.
Best regards,
Andrej
Alexander Bauer (1):
ARM: dts: imx6ull: Add support for PHYTEC phyGATE-Tauri-S with i.MX
6ULL
Andrej Picej (2):
dt-bindings: arm: fsl: add PHYTEC phyGATE Tauri i.MX6 ULL
ARM: dts: imx6ul: peb-av-02: move to 3 cell pwm
Yunus Bas (1):
ARM: dts: imx6ul: phycore: Change USB LDO voltage for usb compliance
.../devicetree/bindings/arm/fsl.yaml | 9 +
arch/arm/boot/dts/Makefile | 2 +
.../boot/dts/imx6ul-phytec-phycore-som.dtsi | 5 +
.../dts/imx6ul-phytec-segin-peb-av-02.dtsi | 3 +-
.../boot/dts/imx6ull-phytec-tauri-emmc.dts | 20 +
.../boot/dts/imx6ull-phytec-tauri-nand.dts | 20 +
arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi | 605 ++++++++++++++++++
7 files changed, 662 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 1/4] dt-bindings: arm: fsl: add PHYTEC phyGATE Tauri i.MX6 ULL
2021-12-01 12:53 ` Andrej Picej
@ 2021-12-01 12:53 ` Andrej Picej
-1 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-01 12:53 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, soc
Cc: robh+dt, kernel, shawnguo, leoyang.li, krzysztof.kozlowski,
linux, festevam, arnd, linux-imx, andrej.picej, y.bas
Add devicetree bindings for phyGATE Tauri board with phyCORE-i.MX6 ULL.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 0b595b26061f..9c37f22b6c61 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -602,6 +602,15 @@ properties:
- const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
- const: fsl,imx6ull
+ - description: i.MX6ULL PHYTEC phyGATE-Tauri
+ items:
+ - enum:
+ - phytec,imx6ull-phygate-tauri-emmc
+ - phytec,imx6ull-phygate-tauri-nand
+ - const: phytec,imx6ull-phygate-tauri # PHYTEC phyGATE-Tauri with i.MX6 ULL
+ - const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
+ - const: fsl,imx6ull
+
- description: i.MX6ULL Boards with Toradex Colibri iMX6ULL Modules
items:
- enum:
--
2.25.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 1/4] dt-bindings: arm: fsl: add PHYTEC phyGATE Tauri i.MX6 ULL
@ 2021-12-01 12:53 ` Andrej Picej
0 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-01 12:53 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, soc
Cc: robh+dt, kernel, shawnguo, leoyang.li, krzysztof.kozlowski,
linux, festevam, arnd, linux-imx, andrej.picej, y.bas
Add devicetree bindings for phyGATE Tauri board with phyCORE-i.MX6 ULL.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 0b595b26061f..9c37f22b6c61 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -602,6 +602,15 @@ properties:
- const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
- const: fsl,imx6ull
+ - description: i.MX6ULL PHYTEC phyGATE-Tauri
+ items:
+ - enum:
+ - phytec,imx6ull-phygate-tauri-emmc
+ - phytec,imx6ull-phygate-tauri-nand
+ - const: phytec,imx6ull-phygate-tauri # PHYTEC phyGATE-Tauri with i.MX6 ULL
+ - const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
+ - const: fsl,imx6ull
+
- description: i.MX6ULL Boards with Toradex Colibri iMX6ULL Modules
items:
- enum:
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 2/4] ARM: dts: imx6ull: Add support for PHYTEC phyGATE-Tauri-S with i.MX 6ULL
2021-12-01 12:53 ` Andrej Picej
@ 2021-12-01 12:53 ` Andrej Picej
-1 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-01 12:53 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, soc
Cc: robh+dt, kernel, shawnguo, leoyang.li, krzysztof.kozlowski,
linux, festevam, arnd, linux-imx, andrej.picej, y.bas
From: Alexander Bauer <a.bauer@phytec.de>
Add support for the PHYTEC phyGATE-Tauri-S with i.MX 6ULL with eMMC or
NAND.
Supported features:
* eMMC/NAND
* i2c RTC
* i2c TEMP
* PMIC
* PWM
* debug UART
* CAN
* SD card
* 2x 1Gbit Ethernet
* RS232/RS485
* USB 2.0 Host
* TPM
* SPI-NOR
Signed-off-by: Alexander Bauer <a.bauer@phytec.de>
Signed-off-by: Jens Lang <j.lang@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
---
arch/arm/boot/dts/Makefile | 2 +
.../boot/dts/imx6ull-phytec-tauri-emmc.dts | 20 +
.../boot/dts/imx6ull-phytec-tauri-nand.dts | 20 +
arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi | 605 ++++++++++++++++++
4 files changed, 647 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..c2bfad6e640e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -693,6 +693,8 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-phytec-segin-ff-rdk-nand.dtb \
imx6ull-phytec-segin-ff-rdk-emmc.dtb \
imx6ull-phytec-segin-lc-rdk-nand.dtb \
+ imx6ull-phytec-tauri-nand.dtb \
+ imx6ull-phytec-tauri-emmc.dtb \
imx6ulz-14x14-evk.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
diff --git a/arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts b/arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts
new file mode 100644
index 000000000000..14adb87da911
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull-phytec-tauri.dtsi"
+
+/ {
+ model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+ compatible = "phytec,imx6ull-phygate-tauri",
+ "phytec,imx6ull-phygate-tauri-emmc",
+ "phytec,imx6ull-pcl063", "fsl,imx6ull";
+};
+
+/* EMMC-Version */
+&usdhc2 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts b/arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts
new file mode 100644
index 000000000000..ae396ac63443
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull-phytec-tauri.dtsi"
+
+/ {
+ model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+ compatible = "phytec,imx6ull-phygate-tauri",
+ "phytec,imx6ull-phygate-tauri-nand",
+ "phytec,imx6ull-pcl063", "fsl,imx6ull";
+};
+
+/* NAND-Version */
+&gpmi {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi b/arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi
new file mode 100644
index 000000000000..62a70d80c009
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi
@@ -0,0 +1,605 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-phytec-phycore-som.dtsi"
+
+/ {
+
+ model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+ compatible = "phytec,imx6ull-phygate-tauri",
+ "phytec,imx6ull-pcl063", "fsl,imx6ull";
+
+ aliases {
+ rtc0 = &i2c_rtc;
+ rtc1 = &snvs_rtc;
+ };
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-key";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ key {
+ label = "KEY-A";
+ gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+ linux,code = <30>;
+ wakeup-source;
+ };
+ };
+
+ reg_adc1_vref_3v3: regulator-vref-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_s25fl064_hold: regulator-s25fl064-hold {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_s25fl064_hold>;
+ compatible = "regulator-fixed";
+ regulator-name = "s25fl064_hold";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 17 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_usb_hub_vbus: regulator-hub-otg1-vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbhubpwr>;
+ compatible = "regulator-fixed";
+ regulator-name = "usb_hub_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1pwr>;
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ user_leds: user-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_user_leds>,
+ <&pinctrl_user_leds_snvs>;
+
+ user-led1 {
+ label = "yellow";
+ gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "off";
+ };
+
+ user-led2 {
+ label = "red";
+ gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "off";
+ };
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ fsl,spi-num-chipselects = <3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>,
+ <&pinctrl_ecspi1_cs>;
+ cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>,
+ <&gpio3 10 GPIO_ACTIVE_LOW>,
+ <&gpio3 11 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ spi_dev0: spi@0 {
+ compatible = "linux,spidev";
+ spi-max-frequency = <57600000>;
+ reg = <0>;
+ };
+
+ tpm_tis: tpm@1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tpm>;
+ compatible = "tcg,tpm_tis-spi";
+ reg = <1>;
+ spi-max-frequency = <20000000>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ status = "okay";
+ };
+
+/* S25FL064P */
+ s25fl064: flash@2 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = " jedec,spi-nor";
+ reg = <2>;
+ spi-max-frequency = <40000000>;
+ m25p,fast-read;
+ status = "disabled";
+ };
+};
+
+&ecspi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ dmas = <&sdma 7 8 0>,
+ <&sdma 8 8 0>;
+ dma-names = "rx", "tx";
+ status = "okay";
+
+ spi_dev1: spi@0 {
+ compatible = "linux,spidev";
+ spi-max-frequency = <57600000>;
+ reg = <0>;
+ };
+};
+
+ðphy1 {
+ status = "okay";
+};
+
+&fec1 {
+ status = "okay";
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy2>;
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ i2c_rtc: rtc@68 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc_int>;
+ compatible = "microcrystal,rv4162";
+ reg = <0x68>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ tmp102: tmp@49 {
+ compatible = "ti,tmp102";
+ reg = <0x49>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tempsense>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ #thermal-sensor-cells = <1>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ sda-gpios = <&gpio1 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ sda-gpios = <&gpio3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+&i2c4 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ pinctrl-1 = <&pinctrl_i2c4_gpio>;
+ sda-gpios = <&gpio3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio3 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+&mdio {
+ ethphy2: ethernet-phy@2 {
+ reg = <2>;
+ micrel,led-mode = <1>;
+ clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+ clock-names = "rmii-ref";
+ status = "okay";
+ };
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&pwm6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm6>;
+ status = "okay";
+};
+
+&pwm7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm7>;
+ status = "okay";
+};
+
+&pwm8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm8>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+/* UART4 * RS485 */
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ rts-gpios = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+ rs485-rts-active-high;
+ linux,rs485-enabled-at-boot-time;
+ status = "okay";
+};
+
+/* UART5 * RS232 */
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart7>;
+ status = "okay";
+};
+
+/* USB */
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1>;
+ vbus-supply = <®_usb_otg1_vbus>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usb_hub_vbus>;
+ disable-over-current;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
+
+&usdhc2 {
+ status = "disabled";
+};
+
+&iomuxc_snvs {
+
+ pinctrl_rtc_int: rtcintgrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x17059
+ >;
+ };
+
+ pinctrl_stmpe: stmpegrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x17059
+ >;
+ };
+
+ pinctrl_tempsense: tempsensegrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x17059
+ >;
+ };
+
+ pinctrl_tpm: tpmgrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x17059
+ >;
+ };
+
+ pinctrl_usbhubpwr: usbhubpwrgrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x17059
+ >;
+ };
+
+ pinctrl_user_leds_snvs: user_ledsgrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x79
+ >;
+ };
+};
+
+&iomuxc {
+
+ pinctrl_gpio: gpio_gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x17059 /* nUART_MUX_RS232 */
+ MX6UL_PAD_CSI_DATA04__GPIO4_IO25 0x17059 /* nUART_MUX_DUAL_RX_TX */
+ >;
+ };
+
+ pinctrl_gpio_keys: gpio_keysgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x79
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x100b1
+ MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO 0x100b1
+ MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x100b1
+ MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x10b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK 0x100b1
+ MX6UL_PAD_LCD_DATA23__ECSPI1_MISO 0x100b1
+ MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi1_cs: ecspi1csgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA21__GPIO3_IO26 0x10b0
+ MX6UL_PAD_LCD_DATA05__GPIO3_IO10 0x10b0
+ MX6UL_PAD_LCD_DATA06__GPIO3_IO11 0x10b0
+ >;
+ };
+
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b010
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b010
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b010
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b010
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA10__FLEXCAN2_TX 0x0b0b0
+ MX6UL_PAD_LCD_DATA11__FLEXCAN2_RX 0x0b0b0
+ >;
+ };
+
+ princtrl_flexcan2_en: flexcan2engrp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x17059
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__I2C2_SCL 0xb0
+ MX6UL_PAD_GPIO1_IO01__I2C2_SDA 0xb0
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__GPIO1_IO00 0xb0
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA01__I2C3_SCL 0xb0
+ MX6UL_PAD_LCD_DATA00__I2C3_SDA 0xb0
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA01__GPIO3_IO06 0xb0
+ MX6UL_PAD_LCD_DATA00__GPIO3_IO05 0xb0
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA03__I2C4_SCL 0xb0
+ MX6UL_PAD_LCD_DATA02__I2C4_SDA 0xb0
+ >;
+ };
+
+ pinctrl_i2c4_gpio: i2c4gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA03__GPIO3_IO08 0xb0
+ MX6UL_PAD_LCD_DATA02__GPIO3_IO07 0xb0
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO04__PWM3_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_pwm6: pwm6grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TDI__PWM6_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_pwm7: pwm7grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TCK__PWM7_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_pwm8: pwm8grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TRST_B__PWM8_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_s25fl064_hold: s25fl064_holdgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA12__GPIO3_IO17 0x100b1
+ >;
+ };
+
+ pinctrl_sai2: sai2grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088
+ MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088
+ MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088
+ MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088
+ MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__UART4_DCE_TX 0x1b0b1
+ MX6UL_PAD_LCD_ENABLE__UART4_DCE_RX 0x1b0b1
+ MX6UL_PAD_LCD_HSYNC__GPIO3_IO02 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart7: uart7grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA16__UART7_DCE_TX 0x1b0b1
+ MX6UL_PAD_LCD_DATA17__UART7_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1: usbotg1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA06__GPIO4_IO27 0x80
+ >;
+ };
+
+ pinctrl_usbotg1pwr: usbotg1pwrgrp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA07__GPIO4_IO28 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_user_leds: user_ledsgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x79
+ >;
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 2/4] ARM: dts: imx6ull: Add support for PHYTEC phyGATE-Tauri-S with i.MX 6ULL
@ 2021-12-01 12:53 ` Andrej Picej
0 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-01 12:53 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, soc
Cc: robh+dt, kernel, shawnguo, leoyang.li, krzysztof.kozlowski,
linux, festevam, arnd, linux-imx, andrej.picej, y.bas
From: Alexander Bauer <a.bauer@phytec.de>
Add support for the PHYTEC phyGATE-Tauri-S with i.MX 6ULL with eMMC or
NAND.
Supported features:
* eMMC/NAND
* i2c RTC
* i2c TEMP
* PMIC
* PWM
* debug UART
* CAN
* SD card
* 2x 1Gbit Ethernet
* RS232/RS485
* USB 2.0 Host
* TPM
* SPI-NOR
Signed-off-by: Alexander Bauer <a.bauer@phytec.de>
Signed-off-by: Jens Lang <j.lang@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
---
arch/arm/boot/dts/Makefile | 2 +
.../boot/dts/imx6ull-phytec-tauri-emmc.dts | 20 +
.../boot/dts/imx6ull-phytec-tauri-nand.dts | 20 +
arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi | 605 ++++++++++++++++++
4 files changed, 647 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts
create mode 100644 arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..c2bfad6e640e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -693,6 +693,8 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-phytec-segin-ff-rdk-nand.dtb \
imx6ull-phytec-segin-ff-rdk-emmc.dtb \
imx6ull-phytec-segin-lc-rdk-nand.dtb \
+ imx6ull-phytec-tauri-nand.dtb \
+ imx6ull-phytec-tauri-emmc.dtb \
imx6ulz-14x14-evk.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
diff --git a/arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts b/arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts
new file mode 100644
index 000000000000..14adb87da911
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull-phytec-tauri.dtsi"
+
+/ {
+ model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+ compatible = "phytec,imx6ull-phygate-tauri",
+ "phytec,imx6ull-phygate-tauri-emmc",
+ "phytec,imx6ull-pcl063", "fsl,imx6ull";
+};
+
+/* EMMC-Version */
+&usdhc2 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts b/arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts
new file mode 100644
index 000000000000..ae396ac63443
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull-phytec-tauri.dtsi"
+
+/ {
+ model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+ compatible = "phytec,imx6ull-phygate-tauri",
+ "phytec,imx6ull-phygate-tauri-nand",
+ "phytec,imx6ull-pcl063", "fsl,imx6ull";
+};
+
+/* NAND-Version */
+&gpmi {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi b/arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi
new file mode 100644
index 000000000000..62a70d80c009
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi
@@ -0,0 +1,605 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-phytec-phycore-som.dtsi"
+
+/ {
+
+ model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+ compatible = "phytec,imx6ull-phygate-tauri",
+ "phytec,imx6ull-pcl063", "fsl,imx6ull";
+
+ aliases {
+ rtc0 = &i2c_rtc;
+ rtc1 = &snvs_rtc;
+ };
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-key";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ key {
+ label = "KEY-A";
+ gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+ linux,code = <30>;
+ wakeup-source;
+ };
+ };
+
+ reg_adc1_vref_3v3: regulator-vref-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_s25fl064_hold: regulator-s25fl064-hold {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_s25fl064_hold>;
+ compatible = "regulator-fixed";
+ regulator-name = "s25fl064_hold";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 17 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_usb_hub_vbus: regulator-hub-otg1-vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbhubpwr>;
+ compatible = "regulator-fixed";
+ regulator-name = "usb_hub_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1pwr>;
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ user_leds: user-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_user_leds>,
+ <&pinctrl_user_leds_snvs>;
+
+ user-led1 {
+ label = "yellow";
+ gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "off";
+ };
+
+ user-led2 {
+ label = "red";
+ gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "off";
+ };
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ fsl,spi-num-chipselects = <3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>,
+ <&pinctrl_ecspi1_cs>;
+ cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>,
+ <&gpio3 10 GPIO_ACTIVE_LOW>,
+ <&gpio3 11 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ spi_dev0: spi@0 {
+ compatible = "linux,spidev";
+ spi-max-frequency = <57600000>;
+ reg = <0>;
+ };
+
+ tpm_tis: tpm@1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tpm>;
+ compatible = "tcg,tpm_tis-spi";
+ reg = <1>;
+ spi-max-frequency = <20000000>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ status = "okay";
+ };
+
+/* S25FL064P */
+ s25fl064: flash@2 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = " jedec,spi-nor";
+ reg = <2>;
+ spi-max-frequency = <40000000>;
+ m25p,fast-read;
+ status = "disabled";
+ };
+};
+
+&ecspi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ dmas = <&sdma 7 8 0>,
+ <&sdma 8 8 0>;
+ dma-names = "rx", "tx";
+ status = "okay";
+
+ spi_dev1: spi@0 {
+ compatible = "linux,spidev";
+ spi-max-frequency = <57600000>;
+ reg = <0>;
+ };
+};
+
+ðphy1 {
+ status = "okay";
+};
+
+&fec1 {
+ status = "okay";
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy2>;
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ i2c_rtc: rtc@68 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc_int>;
+ compatible = "microcrystal,rv4162";
+ reg = <0x68>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ tmp102: tmp@49 {
+ compatible = "ti,tmp102";
+ reg = <0x49>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tempsense>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ #thermal-sensor-cells = <1>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ sda-gpios = <&gpio1 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ sda-gpios = <&gpio3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+&i2c4 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ pinctrl-1 = <&pinctrl_i2c4_gpio>;
+ sda-gpios = <&gpio3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio3 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+&mdio {
+ ethphy2: ethernet-phy@2 {
+ reg = <2>;
+ micrel,led-mode = <1>;
+ clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+ clock-names = "rmii-ref";
+ status = "okay";
+ };
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&pwm6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm6>;
+ status = "okay";
+};
+
+&pwm7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm7>;
+ status = "okay";
+};
+
+&pwm8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm8>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+/* UART4 * RS485 */
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ rts-gpios = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+ rs485-rts-active-high;
+ linux,rs485-enabled-at-boot-time;
+ status = "okay";
+};
+
+/* UART5 * RS232 */
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart7>;
+ status = "okay";
+};
+
+/* USB */
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1>;
+ vbus-supply = <®_usb_otg1_vbus>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usb_hub_vbus>;
+ disable-over-current;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
+
+&usdhc2 {
+ status = "disabled";
+};
+
+&iomuxc_snvs {
+
+ pinctrl_rtc_int: rtcintgrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x17059
+ >;
+ };
+
+ pinctrl_stmpe: stmpegrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x17059
+ >;
+ };
+
+ pinctrl_tempsense: tempsensegrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x17059
+ >;
+ };
+
+ pinctrl_tpm: tpmgrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x17059
+ >;
+ };
+
+ pinctrl_usbhubpwr: usbhubpwrgrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x17059
+ >;
+ };
+
+ pinctrl_user_leds_snvs: user_ledsgrp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x79
+ >;
+ };
+};
+
+&iomuxc {
+
+ pinctrl_gpio: gpio_gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x17059 /* nUART_MUX_RS232 */
+ MX6UL_PAD_CSI_DATA04__GPIO4_IO25 0x17059 /* nUART_MUX_DUAL_RX_TX */
+ >;
+ };
+
+ pinctrl_gpio_keys: gpio_keysgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x79
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x100b1
+ MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO 0x100b1
+ MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x100b1
+ MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x10b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK 0x100b1
+ MX6UL_PAD_LCD_DATA23__ECSPI1_MISO 0x100b1
+ MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi1_cs: ecspi1csgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA21__GPIO3_IO26 0x10b0
+ MX6UL_PAD_LCD_DATA05__GPIO3_IO10 0x10b0
+ MX6UL_PAD_LCD_DATA06__GPIO3_IO11 0x10b0
+ >;
+ };
+
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b010
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b010
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b010
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b010
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA10__FLEXCAN2_TX 0x0b0b0
+ MX6UL_PAD_LCD_DATA11__FLEXCAN2_RX 0x0b0b0
+ >;
+ };
+
+ princtrl_flexcan2_en: flexcan2engrp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x17059
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__I2C2_SCL 0xb0
+ MX6UL_PAD_GPIO1_IO01__I2C2_SDA 0xb0
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__GPIO1_IO00 0xb0
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA01__I2C3_SCL 0xb0
+ MX6UL_PAD_LCD_DATA00__I2C3_SDA 0xb0
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA01__GPIO3_IO06 0xb0
+ MX6UL_PAD_LCD_DATA00__GPIO3_IO05 0xb0
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA03__I2C4_SCL 0xb0
+ MX6UL_PAD_LCD_DATA02__I2C4_SDA 0xb0
+ >;
+ };
+
+ pinctrl_i2c4_gpio: i2c4gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA03__GPIO3_IO08 0xb0
+ MX6UL_PAD_LCD_DATA02__GPIO3_IO07 0xb0
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO04__PWM3_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_pwm6: pwm6grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TDI__PWM6_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_pwm7: pwm7grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TCK__PWM7_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_pwm8: pwm8grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TRST_B__PWM8_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_s25fl064_hold: s25fl064_holdgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA12__GPIO3_IO17 0x100b1
+ >;
+ };
+
+ pinctrl_sai2: sai2grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088
+ MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088
+ MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088
+ MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088
+ MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__UART4_DCE_TX 0x1b0b1
+ MX6UL_PAD_LCD_ENABLE__UART4_DCE_RX 0x1b0b1
+ MX6UL_PAD_LCD_HSYNC__GPIO3_IO02 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart7: uart7grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA16__UART7_DCE_TX 0x1b0b1
+ MX6UL_PAD_LCD_DATA17__UART7_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1: usbotg1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA06__GPIO4_IO27 0x80
+ >;
+ };
+
+ pinctrl_usbotg1pwr: usbotg1pwrgrp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA07__GPIO4_IO28 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_user_leds: user_ledsgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x79
+ >;
+ };
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 3/4] ARM: dts: imx6ul: phycore: Change USB LDO voltage for usb compliance
2021-12-01 12:53 ` Andrej Picej
@ 2021-12-01 12:53 ` Andrej Picej
-1 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-01 12:53 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, soc
Cc: robh+dt, kernel, shawnguo, leoyang.li, krzysztof.kozlowski,
linux, festevam, arnd, linux-imx, andrej.picej, y.bas
From: Yunus Bas <y.bas@phytec.de>
According to the NXP usb compliance reference, the USB data lines for
Full/Low speed are connected to the ARM USB LDO, which is set to
minimum-voltage = 2.6V and maximum-voltage = 3.4 V. When the regulator
is deactivated, the data lines are defaulty driven with 2.6V, which is
not USB Full-Speed compliant. To be compliant, we need to activate the
USB LDO regulator and set it to the value of 3V, which is the specified
value in the USB specification.
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
---
arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi
index 3cddc68917a0..2e03be3d43ec 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi
@@ -83,6 +83,11 @@ eeprom@52 {
};
};
+®_3p0 {
+ regulator-min-microvolt = <3000000>;
+ regulator-always-on;
+};
+
&snvs_poweroff {
status = "okay";
};
--
2.25.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 3/4] ARM: dts: imx6ul: phycore: Change USB LDO voltage for usb compliance
@ 2021-12-01 12:53 ` Andrej Picej
0 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-01 12:53 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, soc
Cc: robh+dt, kernel, shawnguo, leoyang.li, krzysztof.kozlowski,
linux, festevam, arnd, linux-imx, andrej.picej, y.bas
From: Yunus Bas <y.bas@phytec.de>
According to the NXP usb compliance reference, the USB data lines for
Full/Low speed are connected to the ARM USB LDO, which is set to
minimum-voltage = 2.6V and maximum-voltage = 3.4 V. When the regulator
is deactivated, the data lines are defaulty driven with 2.6V, which is
not USB Full-Speed compliant. To be compliant, we need to activate the
USB LDO regulator and set it to the value of 3V, which is the specified
value in the USB specification.
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
---
arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi
index 3cddc68917a0..2e03be3d43ec 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi
@@ -83,6 +83,11 @@ eeprom@52 {
};
};
+®_3p0 {
+ regulator-min-microvolt = <3000000>;
+ regulator-always-on;
+};
+
&snvs_poweroff {
status = "okay";
};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 4/4] ARM: dts: imx6ul: peb-av-02: move to 3 cell pwm
2021-12-01 12:53 ` Andrej Picej
@ 2021-12-01 12:53 ` Andrej Picej
-1 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-01 12:53 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, soc
Cc: robh+dt, kernel, shawnguo, leoyang.li, krzysztof.kozlowski,
linux, festevam, arnd, linux-imx, andrej.picej, y.bas
Instead of changing default pwm-cells property, use the default
"#pwm-cells = <3>" and add the third option.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
---
arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi b/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi
index 7cda6944501d..6ce534a896ef 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi
+++ b/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi
@@ -11,7 +11,7 @@ backlight_lcd: backlight-lcd {
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <5>;
power-supply = <®_backlight_en>;
- pwms = <&pwm3 0 5000000>;
+ pwms = <&pwm3 0 5000000 0>;
status = "disabled";
};
@@ -91,7 +91,6 @@ lcdif_parallel_out: endpoint {
};
&pwm3 {
- #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm3>;
status = "disabled";
--
2.25.1
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 4/4] ARM: dts: imx6ul: peb-av-02: move to 3 cell pwm
@ 2021-12-01 12:53 ` Andrej Picej
0 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-01 12:53 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, soc
Cc: robh+dt, kernel, shawnguo, leoyang.li, krzysztof.kozlowski,
linux, festevam, arnd, linux-imx, andrej.picej, y.bas
Instead of changing default pwm-cells property, use the default
"#pwm-cells = <3>" and add the third option.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
---
arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi b/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi
index 7cda6944501d..6ce534a896ef 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi
+++ b/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi
@@ -11,7 +11,7 @@ backlight_lcd: backlight-lcd {
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <5>;
power-supply = <®_backlight_en>;
- pwms = <&pwm3 0 5000000>;
+ pwms = <&pwm3 0 5000000 0>;
status = "disabled";
};
@@ -91,7 +91,6 @@ lcdif_parallel_out: endpoint {
};
&pwm3 {
- #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm3>;
status = "disabled";
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH 0/4] PHYTEC i.MX 6UL/ULL devicetree patches
2021-12-01 12:53 ` Andrej Picej
@ 2021-12-13 16:13 ` Arnd Bergmann
-1 siblings, 0 replies; 18+ messages in thread
From: Arnd Bergmann @ 2021-12-13 16:13 UTC (permalink / raw)
To: Andrej Picej
Cc: DTML, Linux ARM, SoC Team, Rob Herring, Sascha Hauer, Shawn Guo,
Leo Li, Krzysztof Kozlowski, Oleksij Rempel, Fabio Estevam,
Arnd Bergmann, NXP Linux Team, Yunus Bas
On Wed, Dec 1, 2021 at 1:53 PM Andrej Picej <andrej.picej@norik.com> wrote:
>
> Hi all,
>
> this patch series contains PHYTEC i.MX 6UL/ULL devicetree patches not
> yet upstreamed.
>
> First and second patch add devicetree for relatively new phyGATE
> Tauri-S, which is based on i.MX 6ULL.
>
> Third patch changes USB LDO voltage for i.MX 6UL/ULL phyCORE devices so
> they match USB Full-speed compliance.
>
> The fourth patch moves from using 2 pwm-cell to default 3 cell pwm
> property.
Hi Andrej,
We don't normally merge board specific changes directly into the SoC
tree, please
resend to the i.MX maintainers. You can keep the rest of the Cc list except for
soc@kernel.org.
As a general rule, try to make the "To:" address of the patch series the person
that you expect to act on it, either reviewing or applying.
Arnd
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 0/4] PHYTEC i.MX 6UL/ULL devicetree patches
@ 2021-12-13 16:13 ` Arnd Bergmann
0 siblings, 0 replies; 18+ messages in thread
From: Arnd Bergmann @ 2021-12-13 16:13 UTC (permalink / raw)
To: Andrej Picej
Cc: DTML, Linux ARM, SoC Team, Rob Herring, Sascha Hauer, Shawn Guo,
Leo Li, Krzysztof Kozlowski, Oleksij Rempel, Fabio Estevam,
Arnd Bergmann, NXP Linux Team, Yunus Bas
On Wed, Dec 1, 2021 at 1:53 PM Andrej Picej <andrej.picej@norik.com> wrote:
>
> Hi all,
>
> this patch series contains PHYTEC i.MX 6UL/ULL devicetree patches not
> yet upstreamed.
>
> First and second patch add devicetree for relatively new phyGATE
> Tauri-S, which is based on i.MX 6ULL.
>
> Third patch changes USB LDO voltage for i.MX 6UL/ULL phyCORE devices so
> they match USB Full-speed compliance.
>
> The fourth patch moves from using 2 pwm-cell to default 3 cell pwm
> property.
Hi Andrej,
We don't normally merge board specific changes directly into the SoC
tree, please
resend to the i.MX maintainers. You can keep the rest of the Cc list except for
soc@kernel.org.
As a general rule, try to make the "To:" address of the patch series the person
that you expect to act on it, either reviewing or applying.
Arnd
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 1/4] dt-bindings: arm: fsl: add PHYTEC phyGATE Tauri i.MX6 ULL
2021-12-01 12:53 ` Andrej Picej
@ 2021-12-13 19:15 ` Rob Herring
-1 siblings, 0 replies; 18+ messages in thread
From: Rob Herring @ 2021-12-13 19:15 UTC (permalink / raw)
To: Andrej Picej
Cc: devicetree, linux-arm-kernel, soc, kernel, shawnguo, leoyang.li,
krzysztof.kozlowski, linux, festevam, arnd, linux-imx, y.bas
On Wed, Dec 01, 2021 at 01:53:24PM +0100, Andrej Picej wrote:
> Add devicetree bindings for phyGATE Tauri board with phyCORE-i.MX6 ULL.
>
> Signed-off-by: Andrej Picej <andrej.picej@norik.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index 0b595b26061f..9c37f22b6c61 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -602,6 +602,15 @@ properties:
> - const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
> - const: fsl,imx6ull
>
> + - description: i.MX6ULL PHYTEC phyGATE-Tauri
> + items:
> + - enum:
> + - phytec,imx6ull-phygate-tauri-emmc
> + - phytec,imx6ull-phygate-tauri-nand
> + - const: phytec,imx6ull-phygate-tauri # PHYTEC phyGATE-Tauri with i.MX6 ULL
Is there really a need for 2 compatibles here? Either
phytec,imx6ull-phygate-tauri is specific enough (as nand/emmc can be
described elsewhere) or you need
phytec,imx6ull-phygate-tauri-emmc/phytec,imx6ull-phygate-tauri-nand.
> + - const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
> + - const: fsl,imx6ull
> +
> - description: i.MX6ULL Boards with Toradex Colibri iMX6ULL Modules
> items:
> - enum:
> --
> 2.25.1
>
>
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 1/4] dt-bindings: arm: fsl: add PHYTEC phyGATE Tauri i.MX6 ULL
@ 2021-12-13 19:15 ` Rob Herring
0 siblings, 0 replies; 18+ messages in thread
From: Rob Herring @ 2021-12-13 19:15 UTC (permalink / raw)
To: Andrej Picej
Cc: devicetree, linux-arm-kernel, soc, kernel, shawnguo, leoyang.li,
krzysztof.kozlowski, linux, festevam, arnd, linux-imx, y.bas
On Wed, Dec 01, 2021 at 01:53:24PM +0100, Andrej Picej wrote:
> Add devicetree bindings for phyGATE Tauri board with phyCORE-i.MX6 ULL.
>
> Signed-off-by: Andrej Picej <andrej.picej@norik.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index 0b595b26061f..9c37f22b6c61 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -602,6 +602,15 @@ properties:
> - const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
> - const: fsl,imx6ull
>
> + - description: i.MX6ULL PHYTEC phyGATE-Tauri
> + items:
> + - enum:
> + - phytec,imx6ull-phygate-tauri-emmc
> + - phytec,imx6ull-phygate-tauri-nand
> + - const: phytec,imx6ull-phygate-tauri # PHYTEC phyGATE-Tauri with i.MX6 ULL
Is there really a need for 2 compatibles here? Either
phytec,imx6ull-phygate-tauri is specific enough (as nand/emmc can be
described elsewhere) or you need
phytec,imx6ull-phygate-tauri-emmc/phytec,imx6ull-phygate-tauri-nand.
> + - const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
> + - const: fsl,imx6ull
> +
> - description: i.MX6ULL Boards with Toradex Colibri iMX6ULL Modules
> items:
> - enum:
> --
> 2.25.1
>
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 0/4] PHYTEC i.MX 6UL/ULL devicetree patches
2021-12-13 16:13 ` Arnd Bergmann
@ 2021-12-16 7:13 ` Andrej Picej
-1 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-16 7:13 UTC (permalink / raw)
To: Arnd Bergmann
Cc: DTML, Linux ARM, SoC Team, Rob Herring, Sascha Hauer, Shawn Guo,
Leo Li, Krzysztof Kozlowski, Oleksij Rempel, Fabio Estevam,
NXP Linux Team, Yunus Bas
On 13. 12. 21 17:13, Arnd Bergmann wrote:
> Hi Andrej,
>
> We don't normally merge board specific changes directly into the SoC
> tree, please
> resend to the i.MX maintainers. You can keep the rest of the Cc list except for
> soc@kernel.org.
>
> As a general rule, try to make the "To:" address of the patch series the person
> that you expect to act on it, either reviewing or applying.
>
> Arnd
>
Hi Arnd,
sorry for late reply and thanks for this information.
I will resend the patch series and change the a addresses.
Best regards,
Andrej
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 0/4] PHYTEC i.MX 6UL/ULL devicetree patches
@ 2021-12-16 7:13 ` Andrej Picej
0 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-16 7:13 UTC (permalink / raw)
To: Arnd Bergmann
Cc: DTML, Linux ARM, SoC Team, Rob Herring, Sascha Hauer, Shawn Guo,
Leo Li, Krzysztof Kozlowski, Oleksij Rempel, Fabio Estevam,
NXP Linux Team, Yunus Bas
On 13. 12. 21 17:13, Arnd Bergmann wrote:
> Hi Andrej,
>
> We don't normally merge board specific changes directly into the SoC
> tree, please
> resend to the i.MX maintainers. You can keep the rest of the Cc list except for
> soc@kernel.org.
>
> As a general rule, try to make the "To:" address of the patch series the person
> that you expect to act on it, either reviewing or applying.
>
> Arnd
>
Hi Arnd,
sorry for late reply and thanks for this information.
I will resend the patch series and change the a addresses.
Best regards,
Andrej
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 1/4] dt-bindings: arm: fsl: add PHYTEC phyGATE Tauri i.MX6 ULL
2021-12-13 19:15 ` Rob Herring
@ 2021-12-16 8:45 ` Andrej Picej
-1 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-16 8:45 UTC (permalink / raw)
To: Rob Herring
Cc: devicetree, linux-arm-kernel, soc, kernel, shawnguo, leoyang.li,
krzysztof.kozlowski, linux, festevam, arnd, linux-imx, y.bas
Hi Rob,
On 13. 12. 21 20:15, Rob Herring wrote:
> On Wed, Dec 01, 2021 at 01:53:24PM +0100, Andrej Picej wrote:
>> Add devicetree bindings for phyGATE Tauri board with phyCORE-i.MX6 ULL.
>>
>> Signed-off-by: Andrej Picej <andrej.picej@norik.com>
>> ---
>> Documentation/devicetree/bindings/arm/fsl.yaml | 9 +++++++++
>> 1 file changed, 9 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
>> index 0b595b26061f..9c37f22b6c61 100644
>> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
>> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
>> @@ -602,6 +602,15 @@ properties:
>> - const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
>> - const: fsl,imx6ull
>>
>> + - description: i.MX6ULL PHYTEC phyGATE-Tauri
>> + items:
>> + - enum:
>> + - phytec,imx6ull-phygate-tauri-emmc
>> + - phytec,imx6ull-phygate-tauri-nand
>> + - const: phytec,imx6ull-phygate-tauri # PHYTEC phyGATE-Tauri with i.MX6 ULL
>
> Is there really a need for 2 compatibles here? Either
> phytec,imx6ull-phygate-tauri is specific enough (as nand/emmc can be
> described elsewhere) or you need
> phytec,imx6ull-phygate-tauri-emmc/phytec,imx6ull-phygate-tauri-nand.
sorry for late reply. Yes, I think we need both. We have two board types
for Tauri, one with eMMC and the other with NAND. Depending on this the
NAND or eMMC gets enabled. The same logic is already used with other
PHYTEC boards (e.g. Segin and Mira). Or did you had something other in mind?
>
>
>> + - const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
>> + - const: fsl,imx6ull
>> +
>> - description: i.MX6ULL Boards with Toradex Colibri iMX6ULL Modules
>> items:
>> - enum:
>> --
>> 2.25.1
>>
>>
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 1/4] dt-bindings: arm: fsl: add PHYTEC phyGATE Tauri i.MX6 ULL
@ 2021-12-16 8:45 ` Andrej Picej
0 siblings, 0 replies; 18+ messages in thread
From: Andrej Picej @ 2021-12-16 8:45 UTC (permalink / raw)
To: Rob Herring
Cc: devicetree, linux-arm-kernel, soc, kernel, shawnguo, leoyang.li,
krzysztof.kozlowski, linux, festevam, arnd, linux-imx, y.bas
Hi Rob,
On 13. 12. 21 20:15, Rob Herring wrote:
> On Wed, Dec 01, 2021 at 01:53:24PM +0100, Andrej Picej wrote:
>> Add devicetree bindings for phyGATE Tauri board with phyCORE-i.MX6 ULL.
>>
>> Signed-off-by: Andrej Picej <andrej.picej@norik.com>
>> ---
>> Documentation/devicetree/bindings/arm/fsl.yaml | 9 +++++++++
>> 1 file changed, 9 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
>> index 0b595b26061f..9c37f22b6c61 100644
>> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
>> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
>> @@ -602,6 +602,15 @@ properties:
>> - const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
>> - const: fsl,imx6ull
>>
>> + - description: i.MX6ULL PHYTEC phyGATE-Tauri
>> + items:
>> + - enum:
>> + - phytec,imx6ull-phygate-tauri-emmc
>> + - phytec,imx6ull-phygate-tauri-nand
>> + - const: phytec,imx6ull-phygate-tauri # PHYTEC phyGATE-Tauri with i.MX6 ULL
>
> Is there really a need for 2 compatibles here? Either
> phytec,imx6ull-phygate-tauri is specific enough (as nand/emmc can be
> described elsewhere) or you need
> phytec,imx6ull-phygate-tauri-emmc/phytec,imx6ull-phygate-tauri-nand.
sorry for late reply. Yes, I think we need both. We have two board types
for Tauri, one with eMMC and the other with NAND. Depending on this the
NAND or eMMC gets enabled. The same logic is already used with other
PHYTEC boards (e.g. Segin and Mira). Or did you had something other in mind?
>
>
>> + - const: phytec,imx6ull-pcl063 # PHYTEC phyCORE-i.MX 6ULL
>> + - const: fsl,imx6ull
>> +
>> - description: i.MX6ULL Boards with Toradex Colibri iMX6ULL Modules
>> items:
>> - enum:
>> --
>> 2.25.1
>>
>>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2021-12-16 8:47 UTC | newest]
Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-12-01 12:53 [PATCH 0/4] PHYTEC i.MX 6UL/ULL devicetree patches Andrej Picej
2021-12-01 12:53 ` Andrej Picej
2021-12-01 12:53 ` [PATCH 1/4] dt-bindings: arm: fsl: add PHYTEC phyGATE Tauri i.MX6 ULL Andrej Picej
2021-12-01 12:53 ` Andrej Picej
2021-12-13 19:15 ` Rob Herring
2021-12-13 19:15 ` Rob Herring
2021-12-16 8:45 ` Andrej Picej
2021-12-16 8:45 ` Andrej Picej
2021-12-01 12:53 ` [PATCH 2/4] ARM: dts: imx6ull: Add support for PHYTEC phyGATE-Tauri-S with i.MX 6ULL Andrej Picej
2021-12-01 12:53 ` Andrej Picej
2021-12-01 12:53 ` [PATCH 3/4] ARM: dts: imx6ul: phycore: Change USB LDO voltage for usb compliance Andrej Picej
2021-12-01 12:53 ` Andrej Picej
2021-12-01 12:53 ` [PATCH 4/4] ARM: dts: imx6ul: peb-av-02: move to 3 cell pwm Andrej Picej
2021-12-01 12:53 ` Andrej Picej
2021-12-13 16:13 ` [PATCH 0/4] PHYTEC i.MX 6UL/ULL devicetree patches Arnd Bergmann
2021-12-13 16:13 ` Arnd Bergmann
2021-12-16 7:13 ` Andrej Picej
2021-12-16 7:13 ` Andrej Picej
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.