[PATCH 03/12] rockchip: rk3568-rock-3a: Sync device tree from linux

[Jonas Karlman <jonas@kwiboo.se>]

Running U-Boot from eMMC on a ROCK 3 Model A result in the following:

  U-Boot SPL 2023.04-rc3 (Mar 11 2023 - 17:24:48 +0000)
  Trying to boot from MMC1
  Card did not respond to voltage select! : -110
  spl: mmc init failed with error: -95
  SPL: failed to boot from all boot devices
  ### ERROR ### Please RESET the board ###

The sdhci node is missing in board device tree, sync device tree from
linux v6.3-rc1 to fix booting from eMMC. Also disable sdmmc2 and uart1
nodes related to using a WiFi and BT module in the M2 slot.

Fixes: b44c54f600ab ("arm64: dts: rockchip: rk3568: Add Radxa ROCK 3 Model A board support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
---
 arch/arm/dts/rk3568-rock-3a-u-boot.dtsi |  10 +-
 arch/arm/dts/rk3568-rock-3a.dts         | 261 +++++++++++++++++++++++-
 2 files changed, 262 insertions(+), 9 deletions(-)

diff --git a/arch/arm/dts/rk3568-rock-3a-u-boot.dtsi b/arch/arm/dts/rk3568-rock-3a-u-boot.dtsi
index b5ca23a82a20..04bbb01b5d51 100644
--- a/arch/arm/dts/rk3568-rock-3a-u-boot.dtsi
+++ b/arch/arm/dts/rk3568-rock-3a-u-boot.dtsi
@@ -9,12 +9,16 @@
 / {
 	chosen {
 		stdout-path = &uart2;
-		u-boot,spl-boot-order = "same-as-spl", &sdmmc0;
+		u-boot,spl-boot-order = "same-as-spl", &sdmmc0, &sdhci;
 	};
 };
 
-&sdmmc0 {
-	status = "okay";
+&sdmmc2 {
+	status = "disabled";
+};
+
+&uart1 {
+	status = "disabled";
 };
 
 &uart2 {
diff --git a/arch/arm/dts/rk3568-rock-3a.dts b/arch/arm/dts/rk3568-rock-3a.dts
index a2f2baa4ea91..917f5b2b8aab 100644
--- a/arch/arm/dts/rk3568-rock-3a.dts
+++ b/arch/arm/dts/rk3568-rock-3a.dts
@@ -1,22 +1,37 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
- * Copyright (c) 2023 Akash Gajjar <gajjar04akash@gmail.com>
- */
 
 /dts-v1/;
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
 #include "rk3568.dtsi"
 
 / {
 	model = "Radxa ROCK3 Model A";
 	compatible = "radxa,rock3a", "rockchip,rk3568";
 
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc0;
+	};
+
 	chosen: chosen {
 		stdout-path = "serial2:1500000n8";
 	};
 
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	gmac1_clkin: external-gmac1-clock {
 		compatible = "fixed-clock";
 		clock-frequency = <125000000>;
@@ -24,13 +39,93 @@
 		#clock-cells = <0>;
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		led_user: led-0 {
+			gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&led_user_en>;
+		};
+	};
+
+	rk809-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Analog RK809";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&rk809>;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable>;
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <5000000>;
+		reset-gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_LOW>;
+	};
+
 	vcc12v_dcin: vcc12v-dcin-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc12v_dcin";
 		regulator-always-on;
 		regulator-boot-on;
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
+	};
+
+	pcie30_avdd0v9: pcie30-avdd0v9-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd0v9";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	pcie30_avdd1v8: pcie30-avdd1v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	/* pi6c pcie clock generator */
+	vcc3v3_pi6c_03: vcc3v3-pi6c-03-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pi6c_03";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc3v3_pcie: vcc3v3-pcie-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_enable_h>;
+		regulator-name = "vcc3v3_pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
 	};
 
 	vcc3v3_sys: vcc3v3-sys-regulator {
@@ -91,6 +186,7 @@
 		enable-active-high;
 		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en>;
 		regulator-name = "vcc5v0_usb_otg";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
@@ -164,7 +260,43 @@
 	clock_in_out = "input";
 	phy-handle = <&rgmii_phy1>;
 	phy-mode = "rgmii-id";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_clkinout
+		     &gmac1m1_rgmii_bus>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
 	pinctrl-names = "default";
+	pinctrl-0 = <&hdmitx_scl &hdmitx_sda &hdmitxm1_cec>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
 	status = "okay";
 };
 
@@ -441,6 +573,13 @@
 };
 
 &i2s1_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s1m0_sclktx &i2s1m0_lrcktx &i2s1m0_sdi0 &i2s1m0_sdo0>;
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+&i2s2_2ch {
 	rockchip,trcm-sync-tx-only;
 	status = "okay";
 };
@@ -457,6 +596,27 @@
 	};
 };
 
+&pcie2x1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_h>;
+	reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+	status = "okay";
+};
+
+&pcie30phy {
+	phy-supply = <&vcc3v3_pi6c_03>;
+	status = "okay";
+};
+
+&pcie3x2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie30x2m1_pins>;
+	reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+	status = "okay";
+};
+
 &pinctrl {
 	cam {
 		vcc_cam_en: vcc_cam_en {
@@ -551,6 +711,78 @@
 	status = "okay";
 };
 
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr50;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	bus-width = <4>;
+	disable-wp;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_cmd &sdmmc2m0_clk>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rk809 1>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake &bt_wake &bt_enable>;
+		vbat-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcc_1v8>;
+		/* vddio comes from regulator on module, use IO bank voltage instead */
+	};
+};
+
 &uart2 {
 	status = "okay";
 };
@@ -607,3 +839,20 @@
 	phy-supply = <&vcc5v0_usb_host>;
 	status = "okay";
 };
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
-- 
2.39.2