[PATCH v2 5/5] arm64: dts: meson: a1: support USB controller in OTG mode

[Dmitry Rokosov <ddrokosov@sberdevices.ru>]

Amlogic A1 SoC family has USB2.0 controller based on dwc2 and dwc3
heads. It supports otg/host/peripheral modes.

Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
---
 arch/arm64/boot/dts/amlogic/meson-a1.dtsi | 59 +++++++++++++++++++++++
 1 file changed, 59 insertions(+)

diff --git a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
index ae7d39cff07a..02af0aac6780 100644
--- a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
@@ -8,6 +8,8 @@
 #include <dt-bindings/gpio/meson-a1-gpio.h>
 #include <dt-bindings/clock/amlogic,a1-pll-clkc.h>
 #include <dt-bindings/clock/amlogic,a1-clkc.h>
+#include <dt-bindings/power/meson-a1-power.h>
+#include <dt-bindings/reset/amlogic,meson-a1-reset.h>
 
 / {
 	compatible = "amlogic,a1";
@@ -169,6 +171,17 @@ gpio_intc: interrupt-controller@0440 {
 				amlogic,channel-interrupts =
 					<49 50 51 52 53 54 55 56>;
 			};
+
+			usb2_phy1: phy@4000 {
+				compatible = "amlogic,a1-usb2-phy";
+				clocks = <&clkc CLKID_USB_PHY_IN>;
+				clock-names = "xtal";
+				reg = <0x0 0x4000 0x0 0x60>;
+				resets = <&reset RESET_USBPHY>;
+				reset-names = "phy";
+				#phy-cells = <0>;
+				power-domains = <&pwrc PWRC_USB_ID>;
+			};
 		};
 
 		gic: interrupt-controller@ff901000 {
@@ -192,6 +205,52 @@ spifc: spi@fd000400 {
 			#size-cells = <0>;
 			status = "disabled";
 		};
+
+		usb: usb@fe004400 {
+			status = "disabled";
+			compatible = "amlogic,meson-a1-usb-ctrl";
+			reg = <0x0 0xfe004400 0x0 0xa0>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&clkc CLKID_USB_CTRL>,
+				 <&clkc CLKID_USB_BUS>,
+				 <&clkc CLKID_USB_CTRL_IN>;
+			clock-names = "usb_ctrl", "usb_bus", "xtal_usb_ctrl";
+			resets = <&reset RESET_USBCTRL>;
+			reset-name = "usb_ctrl";
+
+			dr_mode = "otg";
+
+			phys = <&usb2_phy1>;
+			phy-names = "usb2-phy1";
+
+			dwc2: usb@ff500000 {
+				compatible = "amlogic,meson-a1-usb", "snps,dwc2";
+				reg = <0x0 0xff500000 0x0 0x40000>;
+				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb2_phy1>;
+				phy-names = "usb2_phy";
+				clocks = <&clkc CLKID_USB_PHY>;
+				clock-names = "otg";
+				dr_mode = "peripheral";
+				g-rx-fifo-size = <192>;
+				g-np-tx-fifo-size = <128>;
+				g-tx-fifo-size = <128 128 16 16 16>;
+			};
+
+			dwc3: usb@ff400000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0xff400000 0x0 0x100000>;
+				interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				snps,dis_u2_susphy_quirk;
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,parkmode-disable-ss-quirk;
+			};
+		};
 	};
 
 	timer {
-- 
2.36.0


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic