From: Jisheng Zhang <jszhang@kernel.org> To: Conor Dooley <conor@kernel.org>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Paul Walmsley <paul.walmsley@sifive.com>, Palmer Dabbelt <palmer@dabbelt.com>, Albert Ou <aou@eecs.berkeley.edu>, Emil Renner Berthing <kernel@esmil.dk> Cc: linux-riscv@lists.infradead.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org Subject: [PATCH v3 6/6] riscv: dts: starfive: add Milkv Mars board device tree Date: Wed, 31 Jan 2024 21:26:00 +0800 [thread overview] Message-ID: <20240131132600.4067-7-jszhang@kernel.org> (raw) In-Reply-To: <20240131132600.4067-1-jszhang@kernel.org> The Milkv Mars is a development board based on the Starfive JH7110 SoC. The board features: - JH7110 SoC - 1/2/4/8 GiB LPDDR4 DRAM - AXP15060 PMIC - 40 pin GPIO header - 3x USB 3.0 host port - 1x USB 2.0 host port - 1x M.2 E-Key - 1x eMMC slot - 1x MicroSD slot - 1x QSPI Flash - 1x 1Gbps Ethernet port - 1x HDMI port - 1x 2-lane DSI and 1x 4-lane DSI - 1x 2-lane CSI Add the devicetree file describing the currently supported features, namely PMIC, UART, I2C, GPIO, SD card, QSPI Flash, eMMC and Ethernet. Signed-off-by: Jisheng Zhang <jszhang@kernel.org> --- arch/riscv/boot/dts/starfive/Makefile | 1 + .../boot/dts/starfive/jh7110-milkv-mars.dts | 35 +++++++++++++++++++ 2 files changed, 36 insertions(+) create mode 100644 arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile index 0141504c0f5c..2fa0cd7f31c3 100644 --- a/arch/riscv/boot/dts/starfive/Makefile +++ b/arch/riscv/boot/dts/starfive/Makefile @@ -8,5 +8,6 @@ DTC_FLAGS_jh7110-starfive-visionfive-2-v1.3b := -@ dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-beaglev-starlight.dtb dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-starfive-visionfive-v1.dtb +dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-mars.dtb dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.2a.dtb dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.3b.dtb diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts new file mode 100644 index 000000000000..de600e799e7d --- /dev/null +++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts @@ -0,0 +1,35 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2023 Jisheng Zhang <jszhang@kernel.org> + */ + +/dts-v1/; +#include "jh7110-visionfive2-mars-common.dtsi" + +/ { + model = "Milk-V Mars"; + compatible = "milkv,mars", "starfive,jh7110"; +}; + +&gmac0 { + starfive,tx-use-rgmii-clk; + assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>; + assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>; +}; + + +&phy0 { + motorcomm,tx-clk-adj-enabled; + motorcomm,tx-clk-10-inverted; + motorcomm,tx-clk-100-inverted; + motorcomm,tx-clk-1000-inverted; + motorcomm,rx-clk-drv-microamp = <3970>; + motorcomm,rx-data-drv-microamp = <2910>; + rx-internal-delay-ps = <1500>; + tx-internal-delay-ps = <1500>; +}; + +&mmc1 { + disable-wp; + cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>; +}; -- 2.43.0
WARNING: multiple messages have this Message-ID (diff)
From: Jisheng Zhang <jszhang@kernel.org> To: Conor Dooley <conor@kernel.org>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Paul Walmsley <paul.walmsley@sifive.com>, Palmer Dabbelt <palmer@dabbelt.com>, Albert Ou <aou@eecs.berkeley.edu>, Emil Renner Berthing <kernel@esmil.dk> Cc: linux-riscv@lists.infradead.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org Subject: [PATCH v3 6/6] riscv: dts: starfive: add Milkv Mars board device tree Date: Wed, 31 Jan 2024 21:26:00 +0800 [thread overview] Message-ID: <20240131132600.4067-7-jszhang@kernel.org> (raw) In-Reply-To: <20240131132600.4067-1-jszhang@kernel.org> The Milkv Mars is a development board based on the Starfive JH7110 SoC. The board features: - JH7110 SoC - 1/2/4/8 GiB LPDDR4 DRAM - AXP15060 PMIC - 40 pin GPIO header - 3x USB 3.0 host port - 1x USB 2.0 host port - 1x M.2 E-Key - 1x eMMC slot - 1x MicroSD slot - 1x QSPI Flash - 1x 1Gbps Ethernet port - 1x HDMI port - 1x 2-lane DSI and 1x 4-lane DSI - 1x 2-lane CSI Add the devicetree file describing the currently supported features, namely PMIC, UART, I2C, GPIO, SD card, QSPI Flash, eMMC and Ethernet. Signed-off-by: Jisheng Zhang <jszhang@kernel.org> --- arch/riscv/boot/dts/starfive/Makefile | 1 + .../boot/dts/starfive/jh7110-milkv-mars.dts | 35 +++++++++++++++++++ 2 files changed, 36 insertions(+) create mode 100644 arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile index 0141504c0f5c..2fa0cd7f31c3 100644 --- a/arch/riscv/boot/dts/starfive/Makefile +++ b/arch/riscv/boot/dts/starfive/Makefile @@ -8,5 +8,6 @@ DTC_FLAGS_jh7110-starfive-visionfive-2-v1.3b := -@ dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-beaglev-starlight.dtb dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-starfive-visionfive-v1.dtb +dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-mars.dtb dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.2a.dtb dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.3b.dtb diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts new file mode 100644 index 000000000000..de600e799e7d --- /dev/null +++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts @@ -0,0 +1,35 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2023 Jisheng Zhang <jszhang@kernel.org> + */ + +/dts-v1/; +#include "jh7110-visionfive2-mars-common.dtsi" + +/ { + model = "Milk-V Mars"; + compatible = "milkv,mars", "starfive,jh7110"; +}; + +&gmac0 { + starfive,tx-use-rgmii-clk; + assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>; + assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>; +}; + + +&phy0 { + motorcomm,tx-clk-adj-enabled; + motorcomm,tx-clk-10-inverted; + motorcomm,tx-clk-100-inverted; + motorcomm,tx-clk-1000-inverted; + motorcomm,rx-clk-drv-microamp = <3970>; + motorcomm,rx-data-drv-microamp = <2910>; + rx-internal-delay-ps = <1500>; + tx-internal-delay-ps = <1500>; +}; + +&mmc1 { + disable-wp; + cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>; +}; -- 2.43.0 _______________________________________________ linux-riscv mailing list linux-riscv@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-riscv
next prev parent reply other threads:[~2024-01-31 13:39 UTC|newest] Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top 2024-01-31 13:25 [PATCH v3 0/6] riscv: dts: starfive: add Milkv Mars board device tree Jisheng Zhang 2024-01-31 13:25 ` Jisheng Zhang 2024-01-31 13:25 ` [PATCH v3 1/6] riscv: dts: starfive: add 'cpus' label to jh7110 and jh7100 soc dtsi Jisheng Zhang 2024-01-31 13:25 ` Jisheng Zhang 2024-04-19 22:04 ` Emil Renner Berthing 2024-04-19 22:04 ` Emil Renner Berthing 2024-01-31 13:25 ` [PATCH v3 2/6] dt-bindings: riscv: starfive: add Milkv Mars board Jisheng Zhang 2024-01-31 13:25 ` Jisheng Zhang 2024-04-19 22:04 ` Emil Renner Berthing 2024-04-19 22:04 ` Emil Renner Berthing 2024-01-31 13:25 ` [PATCH v3 3/6] riscv: dts: starfive: visionfive 2: update sound and codec dt node name Jisheng Zhang 2024-01-31 13:25 ` Jisheng Zhang 2024-04-19 22:05 ` Emil Renner Berthing 2024-04-19 22:05 ` Emil Renner Berthing 2024-01-31 13:25 ` [PATCH v3 4/6] riscv: dts: starfive: visionfive 2: use cpus label for timebase freq Jisheng Zhang 2024-01-31 13:25 ` Jisheng Zhang 2024-04-19 22:05 ` Emil Renner Berthing 2024-04-19 22:05 ` Emil Renner Berthing 2024-01-31 13:25 ` [PATCH v3 5/6] riscv: dts: starfive: introduce a common board dtsi for jh7110 based boards Jisheng Zhang 2024-01-31 13:25 ` Jisheng Zhang 2024-01-31 13:26 ` Jisheng Zhang [this message] 2024-01-31 13:26 ` [PATCH v3 6/6] riscv: dts: starfive: add Milkv Mars board device tree Jisheng Zhang 2024-02-06 19:13 ` Conor Dooley 2024-02-06 19:13 ` Conor Dooley 2024-03-27 18:06 ` Conor Dooley 2024-03-27 18:06 ` Conor Dooley 2024-03-28 10:08 ` Jisheng Zhang 2024-03-28 10:08 ` Jisheng Zhang 2024-03-28 12:45 ` Emil Renner Berthing 2024-03-28 12:45 ` Emil Renner Berthing 2024-03-29 2:32 ` Jisheng Zhang 2024-03-29 2:32 ` Jisheng Zhang 2024-03-28 21:28 ` Heinrich Schuchardt 2024-03-28 21:28 ` Heinrich Schuchardt 2024-03-29 2:31 ` Jisheng Zhang 2024-03-29 2:31 ` Jisheng Zhang 2024-04-01 13:28 ` Heinrich Schuchardt 2024-04-01 13:28 ` Heinrich Schuchardt 2024-04-01 14:44 ` Jisheng Zhang 2024-04-01 14:44 ` Jisheng Zhang 2024-04-19 22:11 ` Emil Renner Berthing 2024-04-19 22:11 ` Emil Renner Berthing
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20240131132600.4067-7-jszhang@kernel.org \ --to=jszhang@kernel.org \ --cc=aou@eecs.berkeley.edu \ --cc=conor@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=kernel@esmil.dk \ --cc=krzysztof.kozlowski+dt@linaro.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-riscv@lists.infradead.org \ --cc=palmer@dabbelt.com \ --cc=paul.walmsley@sifive.com \ --cc=robh+dt@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.