Re: [PATCH v11 3/6] arm64: dts: allwinner: Add Allwinner H616 .dtsi file

["Jernej Škrabec" <jernej.skrabec@gmail.com>]

Hi!

Dne petek, 29. april 2022 ob 01:09:30 CEST je Andre Przywara napisal(a):
> This (relatively) new SoC is similar to the H6, but drops the (broken)
> PCIe support and the USB 3.0 controller. It also gets the management
> controller removed, which in turn removes *some*, but not all of the
> devices formerly dedicated to the ARISC (CPUS).
> And while there is still the extra sunxi interrupt controller, the
> package lacks the corresponding NMI pin, so no interrupts for the PMIC.
> 
> The reserved memory node is actually handled by Trusted Firmware now,
> but U-Boot fails to propagate this to a separately loaded DTB, so we
> keep it in here for now, until U-Boot learns to do this properly.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 574 ++++++++++++++++++
>  1 file changed, 574 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> 
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/
boot/dts/allwinner/sun50i-h616.dtsi
> new file mode 100644
> index 000000000000..cc06cdd15ba5
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> @@ -0,0 +1,574 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +// Copyright (C) 2020 Arm Ltd.
> +// based on the H6 dtsi, which is:
> +//   Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/sun50i-h616-ccu.h>
> +#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
> +#include <dt-bindings/reset/sun50i-h616-ccu.h>
> +#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
> +
> +/ {
> +	interrupt-parent = <&gic>;
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu0: cpu@0 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			reg = <0>;
> +			enable-method = "psci";
> +			clocks = <&ccu CLK_CPUX>;
> +		};
> +
> +		cpu1: cpu@1 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			reg = <1>;
> +			enable-method = "psci";
> +			clocks = <&ccu CLK_CPUX>;
> +		};
> +
> +		cpu2: cpu@2 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			reg = <2>;
> +			enable-method = "psci";
> +			clocks = <&ccu CLK_CPUX>;
> +		};
> +
> +		cpu3: cpu@3 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			reg = <3>;
> +			enable-method = "psci";
> +			clocks = <&ccu CLK_CPUX>;
> +		};
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		/* 512KiB reserved for ARM Trusted Firmware (BL31) */
> +		secmon_reserved: secmon@40000000 {
> +			reg = <0x0 0x40000000 0x0 0x80000>;
> +			no-map;
> +		};
> +	};

I'm not a fan of above. If anything changes in future in BL31, U-Boot would 
need to reconfigure it anyway. Can we just skip it?

> +
> +	osc24M: osc24M-clk {
> +		#clock-cells = <0>;
> +		compatible = "fixed-clock";
> +		clock-frequency = <24000000>;
> +		clock-output-names = "osc24M";
> +	};
> +
> +	pmu {
> +		compatible = "arm,cortex-a53-pmu";
> +		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-0.2";
> +		method = "smc";
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		arm,no-tick-in-suspend;
> +		interrupts = <GIC_PPI 13
> +			(GIC_CPU_MASK_SIMPLE(4) | 
IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 14
> +			(GIC_CPU_MASK_SIMPLE(4) | 
IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 11
> +			(GIC_CPU_MASK_SIMPLE(4) | 
IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 10
> +			(GIC_CPU_MASK_SIMPLE(4) | 
IRQ_TYPE_LEVEL_HIGH)>;
> +	};

Vendor kernel sets IRQ to low level. What is the difference?

> +
> +	soc@0 {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0x0 0x0 0x0 0x40000000>;
> +
> +		syscon: syscon@3000000 {
> +			compatible = "allwinner,sun50i-h616-system-
control";
> +			reg = <0x03000000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			sram_c: sram@28000 {
> +				compatible = "mmio-sram";
> +				reg = <0x00028000 0x30000>;
> +				#address-cells = <1>;
> +				#size-cells = <1>;
> +				ranges = <0 0x00028000 0x30000>;
> +			};
> +		};
> +
> +		ccu: clock@3001000 {
> +			compatible = "allwinner,sun50i-h616-ccu";
> +			reg = <0x03001000 0x1000>;
> +			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
> +			clock-names = "hosc", "losc", "iosc";
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +		};
> +
> +		watchdog: watchdog@30090a0 {
> +			compatible = "allwinner,sun50i-h616-wdt",
> +				     "allwinner,sun6i-a31-wdt";
> +			reg = <0x030090a0 0x20>;
> +			interrupts = <GIC_SPI 50 
IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&osc24M>;
> +		};
> +
> +		pio: pinctrl@300b000 {
> +			compatible = "allwinner,sun50i-h616-pinctrl";
> +			reg = <0x0300b000 0x400>;
> +			interrupts = <GIC_SPI 51 
IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 52 
IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 53 
IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 43 
IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 54 
IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 55 
IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 56 
IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 57 
IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 
0>;
> +			clock-names = "apb", "hosc", "losc";
> +			gpio-controller;
> +			#gpio-cells = <3>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +
> +			ext_rgmii_pins: rgmii-pins {
> +				pins = "PI0", "PI1", "PI2", "PI3", 
"PI4",
> +				       "PI5", "PI7", "PI8", "PI9", 
"PI10",
> +				       "PI11", "PI12", "PI13", 
"PI14", "PI15",
> +				       "PI16";
> +				function = "emac0";
> +				drive-strength = <40>;
> +			};
> +
> +			i2c0_pins: i2c0-pins {
> +				pins = "PI6", "PI7";
> +				function = "i2c0";
> +			};
> +
> +			i2c3_ph_pins: i2c3-ph-pins {
> +				pins = "PH4", "PH5";
> +				function = "i2c3";
> +			};
> +
> +			ir_rx_pin: ir-rx-pin {
> +				pins = "PH10";
> +				function = "ir_rx";
> +			};
> +
> +			mmc0_pins: mmc0-pins {
> +				pins = "PF0", "PF1", "PF2", "PF3",
> +				       "PF4", "PF5";
> +				function = "mmc0";
> +				drive-strength = <30>;
> +				bias-pull-up;
> +			};
> +
> +			mmc1_pins: mmc1-pins {
> +				pins = "PG0", "PG1", "PG2", "PG3",
> +				       "PG4", "PG5";
> +				function = "mmc1";
> +				drive-strength = <30>;
> +				bias-pull-up;
> +			};
> +
> +			mmc2_pins: mmc2-pins {
> +				pins = "PC0", "PC1", "PC5", "PC6",
> +				       "PC8", "PC9", "PC10", 
"PC11",
> +				       "PC13", "PC14", "PC15", 
"PC16";
> +				function = "mmc2";
> +				drive-strength = <30>;
> +				bias-pull-up;
> +			};
> +
> +			spi0_pins: spi0-pins {
> +				pins = "PC0", "PC2", "PC3", "PC4";
> +				function = "spi0";
> +			};
> +
> +			spi1_pins: spi1-pins {
> +				pins = "PH6", "PH7", "PH8";
> +				function = "spi1";
> +			};
> +
> +			spi1_cs_pin: spi1-cs-pin {
> +				pins = "PH5";
> +				function = "spi1";
> +			};
> +
> +			uart0_ph_pins: uart0-ph-pins {
> +				pins = "PH0", "PH1";
> +				function = "uart0";
> +			};
> +
> +			uart1_pins: uart1-pins {
> +				pins = "PG6", "PG7";
> +				function = "uart1";
> +			};
> +
> +			uart1_rts_cts_pins: uart1-rts-cts-pins {
> +				pins = "PG8", "PG9";
> +				function = "uart1";
> +			};

Please add /omit-if-no-ref/ where applicable.

> +		};
> +
> +		gic: interrupt-controller@3021000 {
> +			compatible = "arm,gic-400";
> +			reg = <0x03021000 0x1000>,
> +			      <0x03022000 0x2000>,
> +			      <0x03024000 0x2000>,
> +			      <0x03026000 0x2000>;
> +			interrupts = <GIC_PPI 9 
(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +		};
> +
> +		mmc0: mmc@4020000 {
> +			compatible = "allwinner,sun50i-h616-mmc",
> +				     "allwinner,sun50i-a100-mmc";
> +			reg = <0x04020000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC0>, <&ccu 
CLK_MMC0>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC0>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 35 
IRQ_TYPE_LEVEL_HIGH>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mmc0_pins>;
> +			status = "disabled";
> +			max-frequency = <150000000>;
> +			cap-sd-highspeed;
> +			cap-mmc-highspeed;
> +			mmc-ddr-3_3v;
> +			cap-sdio-irq;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		mmc1: mmc@4021000 {
> +			compatible = "allwinner,sun50i-h616-mmc",
> +				     "allwinner,sun50i-a100-mmc";
> +			reg = <0x04021000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC1>, <&ccu 
CLK_MMC1>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC1>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 36 
IRQ_TYPE_LEVEL_HIGH>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mmc1_pins>;
> +			status = "disabled";
> +			max-frequency = <150000000>;
> +			cap-sd-highspeed;
> +			cap-mmc-highspeed;
> +			mmc-ddr-3_3v;
> +			cap-sdio-irq;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		mmc2: mmc@4022000 {
> +			compatible = "allwinner,sun50i-h616-emmc",
> +				     "allwinner,sun50i-a100-emmc";
> +			reg = <0x04022000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC2>, <&ccu 
CLK_MMC2>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC2>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 37 
IRQ_TYPE_LEVEL_HIGH>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mmc2_pins>;
> +			status = "disabled";
> +			max-frequency = <150000000>;
> +			cap-sd-highspeed;
> +			cap-mmc-highspeed;
> +			mmc-ddr-3_3v;
> +			cap-sdio-irq;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		uart0: serial@5000000 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05000000 0x400>;
> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART0>;
> +			resets = <&ccu RST_BUS_UART0>;
> +			status = "disabled";
> +		};
> +
> +		uart1: serial@5000400 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05000400 0x400>;
> +			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART1>;
> +			resets = <&ccu RST_BUS_UART1>;
> +			status = "disabled";
> +		};
> +
> +		uart2: serial@5000800 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05000800 0x400>;
> +			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART2>;
> +			resets = <&ccu RST_BUS_UART2>;
> +			status = "disabled";
> +		};
> +
> +		uart3: serial@5000c00 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05000c00 0x400>;
> +			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART3>;
> +			resets = <&ccu RST_BUS_UART3>;
> +			status = "disabled";
> +		};
> +
> +		uart4: serial@5001000 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05001000 0x400>;
> +			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART4>;
> +			resets = <&ccu RST_BUS_UART4>;
> +			status = "disabled";
> +		};
> +
> +		uart5: serial@5001400 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05001400 0x400>;
> +			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART5>;
> +			resets = <&ccu RST_BUS_UART5>;
> +			status = "disabled";
> +		};
> +
> +		i2c0: i2c@5002000 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x05002000 0x400>;
> +			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_I2C0>;
> +			resets = <&ccu RST_BUS_I2C0>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&i2c0_pins>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		i2c1: i2c@5002400 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x05002400 0x400>;
> +			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_I2C1>;
> +			resets = <&ccu RST_BUS_I2C1>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		i2c2: i2c@5002800 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x05002800 0x400>;
> +			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_I2C2>;
> +			resets = <&ccu RST_BUS_I2C2>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		i2c3: i2c@5002c00 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x05002c00 0x400>;
> +			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_I2C3>;
> +			resets = <&ccu RST_BUS_I2C3>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		i2c4: i2c@5003000 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x05003000 0x400>;
> +			interrupts = <GIC_SPI 10 
IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_I2C4>;
> +			resets = <&ccu RST_BUS_I2C4>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		spi0: spi@5010000 {
> +			compatible = "allwinner,sun50i-h616-spi",
> +				     "allwinner,sun8i-h3-spi";
> +			reg = <0x05010000 0x1000>;
> +			interrupts = <GIC_SPI 12 
IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_SPI0>, <&ccu 
CLK_SPI0>;
> +			clock-names = "ahb", "mod";
> +			resets = <&ccu RST_BUS_SPI0>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&spi0_pins>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		spi1: spi@5011000 {
> +			compatible = "allwinner,sun50i-h616-spi",
> +				     "allwinner,sun8i-h3-spi";
> +			reg = <0x05011000 0x1000>;
> +			interrupts = <GIC_SPI 13 
IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_SPI1>, <&ccu 
CLK_SPI1>;
> +			clock-names = "ahb", "mod";
> +			resets = <&ccu RST_BUS_SPI1>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&spi1_pins>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		emac0: ethernet@5020000 {
> +			compatible = "allwinner,sun50i-h616-emac",
> +				     "allwinner,sun50i-a64-emac";
> +			syscon = <&syscon>;
> +			reg = <0x05020000 0x10000>;
> +			interrupts = <GIC_SPI 14 
IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "macirq";
> +			resets = <&ccu RST_BUS_EMAC0>;
> +			reset-names = "stmmaceth";
> +			clocks = <&ccu CLK_BUS_EMAC0>;
> +			clock-names = "stmmaceth";
> +			status = "disabled";
> +
> +			mdio0: mdio {
> +				compatible = "snps,dwmac-mdio";
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
> +		};
> +
> +		rtc: rtc@7000000 {
> +			compatible = "allwinner,sun50i-h616-rtc";
> +			reg = <0x07000000 0x400>;
> +			interrupts = <GIC_SPI 101 
IRQ_TYPE_LEVEL_HIGH>;

Above interrupt doesn't seem to be correct according to documentation. It 
should be 104.

> +			clocks = <&r_ccu CLK_R_APB1_RTC>, <&osc24M>,
> +				 <&ccu CLK_PLL_SYSTEM_32K>;
> +			clock-names = "bus", "hosc",
> +				      "pll-32k";
> +			clock-output-names = "osc32k", "osc32k-out", 
"iosc";
> +			#clock-cells = <1>;
> +		};
> +
> +		r_ccu: clock@7010000 {
> +			compatible = "allwinner,sun50i-h616-r-ccu";
> +			reg = <0x07010000 0x210>;
> +			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
> +				 <&ccu CLK_PLL_PERIPH0>;
> +			clock-names = "hosc", "losc", "iosc", "pll-
periph";
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +		};
> +
> +		r_pio: pinctrl@7022000 {
> +			compatible = "allwinner,sun50i-h616-r-
pinctrl";
> +			reg = <0x07022000 0x400>;
> +			interrupts = <GIC_SPI 43 
IRQ_TYPE_LEVEL_HIGH>;

Above interrupt is already used for port E in first pinctrl. Is this shared 
somehow?

Best regards,
Jernej

> +			clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, 
<&rtc 0>;
> +			clock-names = "apb", "hosc", "losc";
> +			gpio-controller;
> +			#gpio-cells = <3>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +
> +			r_i2c_pins: r-i2c-pins {
> +				pins = "PL0", "PL1";
> +				function = "s_i2c";
> +			};
> +
> +			r_rsb_pins: r-rsb-pins {
> +				pins = "PL0", "PL1";
> +				function = "s_rsb";
> +			};
> +		};
> +
> +		ir: ir@7040000 {
> +			compatible = "allwinner,sun50i-h616-ir",
> +				     "allwinner,sun6i-a31-ir";
> +			reg = <0x07040000 0x400>;
> +			interrupts = <GIC_SPI 106 
IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&r_ccu CLK_R_APB1_IR>,
> +				 <&r_ccu CLK_IR>;
> +			clock-names = "apb", "ir";
> +			resets = <&r_ccu RST_R_APB1_IR>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&ir_rx_pin>;
> +			status = "disabled";
> +		};
> +
> +		r_i2c: i2c@7081400 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x07081400 0x400>;
> +			interrupts = <GIC_SPI 105 
IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&r_ccu CLK_R_APB2_I2C>;
> +			resets = <&r_ccu RST_R_APB2_I2C>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		r_rsb: rsb@7083000 {
> +			compatible = "allwinner,sun50i-h616-rsb",
> +				     "allwinner,sun8i-a23-rsb";
> +			reg = <0x07083000 0x400>;
> +			interrupts = <GIC_SPI 109 
IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&r_ccu CLK_R_APB2_RSB>;
> +			clock-frequency = <3000000>;
> +			resets = <&r_ccu RST_R_APB2_RSB>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&r_rsb_pins>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +	};
> +};
> -- 
> 2.35.3
> 
>