* [PATCH v8] ARM: dts: qcom: ipq4019: add USB devicetree nodes
@ 2020-09-09 16:38 Robert Marko
2020-10-02 17:39 ` Robert Marko
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Robert Marko @ 2020-09-09 16:38 UTC (permalink / raw)
To: agross, bjorn.andersson, robh+dt, linux-arm-msm, devicetree,
linux-kernel
Cc: John Crispin, Robert Marko, Luka Perkov, Vinod Koul
From: John Crispin <john@phrozen.org>
Since we now have driver for the USB PHY, and USB controller is already supported by the DWC3 driver lets add the necessary nodes to DTSI.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
---
Changes from v7 to v8:
* Add labels for usb2 and usb3 nodes
Changes from v6 to v7:
* Remove changes to qcom-ipq4019-ap.dk01.1.dtsi
It has slipped in unwanted, we only want to add
nodes to the DTSI.
arch/arm/boot/dts/qcom-ipq4019.dtsi | 74 +++++++++++++++++++++++++++++
1 file changed, 74 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index 74d8e2c8e4b3..4a973253024a 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -605,5 +605,79 @@ ethphy4: ethernet-phy@4 {
reg = <4>;
};
};
+
+ usb3_ss_phy: ssphy@9a000 {
+ compatible = "qcom,usb-ss-ipq4019-phy";
+ #phy-cells = <0>;
+ reg = <0x9a000 0x800>;
+ reg-names = "phy_base";
+ resets = <&gcc USB3_UNIPHY_PHY_ARES>;
+ reset-names = "por_rst";
+ status = "disabled";
+ };
+
+ usb3_hs_phy: hsphy@a6000 {
+ compatible = "qcom,usb-hs-ipq4019-phy";
+ #phy-cells = <0>;
+ reg = <0xa6000 0x40>;
+ reg-names = "phy_base";
+ resets = <&gcc USB3_HSPHY_POR_ARES>, <&gcc USB3_HSPHY_S_ARES>;
+ reset-names = "por_rst", "srif_rst";
+ status = "disabled";
+ };
+
+ usb3: usb3@8af8800 {
+ compatible = "qcom,dwc3";
+ reg = <0x8af8800 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&gcc GCC_USB3_MASTER_CLK>,
+ <&gcc GCC_USB3_SLEEP_CLK>,
+ <&gcc GCC_USB3_MOCK_UTMI_CLK>;
+ clock-names = "master", "sleep", "mock_utmi";
+ ranges;
+ status = "disabled";
+
+ dwc3@8a00000 {
+ compatible = "snps,dwc3";
+ reg = <0x8a00000 0xf8000>;
+ interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb3_hs_phy>, <&usb3_ss_phy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ dr_mode = "host";
+ };
+ };
+
+ usb2_hs_phy: hsphy@a8000 {
+ compatible = "qcom,usb-hs-ipq4019-phy";
+ #phy-cells = <0>;
+ reg = <0xa8000 0x40>;
+ reg-names = "phy_base";
+ resets = <&gcc USB2_HSPHY_POR_ARES>, <&gcc USB2_HSPHY_S_ARES>;
+ reset-names = "por_rst", "srif_rst";
+ status = "disabled";
+ };
+
+ usb2: usb2@60f8800 {
+ compatible = "qcom,dwc3";
+ reg = <0x60f8800 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&gcc GCC_USB2_MASTER_CLK>,
+ <&gcc GCC_USB2_SLEEP_CLK>,
+ <&gcc GCC_USB2_MOCK_UTMI_CLK>;
+ clock-names = "master", "sleep", "mock_utmi";
+ ranges;
+ status = "disabled";
+
+ dwc3@6000000 {
+ compatible = "snps,dwc3";
+ reg = <0x6000000 0xf8000>;
+ interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb2_hs_phy>;
+ phy-names = "usb2-phy";
+ dr_mode = "host";
+ };
+ };
};
};
--
2.26.2
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH v8] ARM: dts: qcom: ipq4019: add USB devicetree nodes
2020-09-09 16:38 [PATCH v8] ARM: dts: qcom: ipq4019: add USB devicetree nodes Robert Marko
@ 2020-10-02 17:39 ` Robert Marko
2020-11-04 13:44 ` Robert Marko
2021-01-22 21:40 ` patchwork-bot+linux-arm-msm
2 siblings, 0 replies; 4+ messages in thread
From: Robert Marko @ 2020-10-02 17:39 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, robh+dt, linux-arm-msm, devicetree,
linux-kernel
Cc: John Crispin, Luka Perkov, Vinod Koul
On Wed, Sep 9, 2020 at 6:38 PM Robert Marko <robert.marko@sartura.hr> wrote:
>
> From: John Crispin <john@phrozen.org>
>
> Since we now have driver for the USB PHY, and USB controller is already supported by the DWC3 driver lets add the necessary nodes to DTSI.
>
> Signed-off-by: John Crispin <john@phrozen.org>
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> Cc: Luka Perkov <luka.perkov@sartura.hr>
> Reviewed-by: Vinod Koul <vkoul@kernel.org>
> ---
> Changes from v7 to v8:
> * Add labels for usb2 and usb3 nodes
> Changes from v6 to v7:
> * Remove changes to qcom-ipq4019-ap.dk01.1.dtsi
> It has slipped in unwanted, we only want to add
> nodes to the DTSI.
>
> arch/arm/boot/dts/qcom-ipq4019.dtsi | 74 +++++++++++++++++++++++++++++
> 1 file changed, 74 insertions(+)
>
> diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
> index 74d8e2c8e4b3..4a973253024a 100644
> --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
> +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
> @@ -605,5 +605,79 @@ ethphy4: ethernet-phy@4 {
> reg = <4>;
> };
> };
> +
> + usb3_ss_phy: ssphy@9a000 {
> + compatible = "qcom,usb-ss-ipq4019-phy";
> + #phy-cells = <0>;
> + reg = <0x9a000 0x800>;
> + reg-names = "phy_base";
> + resets = <&gcc USB3_UNIPHY_PHY_ARES>;
> + reset-names = "por_rst";
> + status = "disabled";
> + };
> +
> + usb3_hs_phy: hsphy@a6000 {
> + compatible = "qcom,usb-hs-ipq4019-phy";
> + #phy-cells = <0>;
> + reg = <0xa6000 0x40>;
> + reg-names = "phy_base";
> + resets = <&gcc USB3_HSPHY_POR_ARES>, <&gcc USB3_HSPHY_S_ARES>;
> + reset-names = "por_rst", "srif_rst";
> + status = "disabled";
> + };
> +
> + usb3: usb3@8af8800 {
> + compatible = "qcom,dwc3";
> + reg = <0x8af8800 0x100>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + clocks = <&gcc GCC_USB3_MASTER_CLK>,
> + <&gcc GCC_USB3_SLEEP_CLK>,
> + <&gcc GCC_USB3_MOCK_UTMI_CLK>;
> + clock-names = "master", "sleep", "mock_utmi";
> + ranges;
> + status = "disabled";
> +
> + dwc3@8a00000 {
> + compatible = "snps,dwc3";
> + reg = <0x8a00000 0xf8000>;
> + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&usb3_hs_phy>, <&usb3_ss_phy>;
> + phy-names = "usb2-phy", "usb3-phy";
> + dr_mode = "host";
> + };
> + };
> +
> + usb2_hs_phy: hsphy@a8000 {
> + compatible = "qcom,usb-hs-ipq4019-phy";
> + #phy-cells = <0>;
> + reg = <0xa8000 0x40>;
> + reg-names = "phy_base";
> + resets = <&gcc USB2_HSPHY_POR_ARES>, <&gcc USB2_HSPHY_S_ARES>;
> + reset-names = "por_rst", "srif_rst";
> + status = "disabled";
> + };
> +
> + usb2: usb2@60f8800 {
> + compatible = "qcom,dwc3";
> + reg = <0x60f8800 0x100>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + clocks = <&gcc GCC_USB2_MASTER_CLK>,
> + <&gcc GCC_USB2_SLEEP_CLK>,
> + <&gcc GCC_USB2_MOCK_UTMI_CLK>;
> + clock-names = "master", "sleep", "mock_utmi";
> + ranges;
> + status = "disabled";
> +
> + dwc3@6000000 {
> + compatible = "snps,dwc3";
> + reg = <0x6000000 0xf8000>;
> + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&usb2_hs_phy>;
> + phy-names = "usb2-phy";
> + dr_mode = "host";
> + };
> + };
> };
> };
> --
> 2.26.2
>
Hi,
Is there an issue with the patch preventing the review?
Regards,
Robert
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH v8] ARM: dts: qcom: ipq4019: add USB devicetree nodes
2020-09-09 16:38 [PATCH v8] ARM: dts: qcom: ipq4019: add USB devicetree nodes Robert Marko
2020-10-02 17:39 ` Robert Marko
@ 2020-11-04 13:44 ` Robert Marko
2021-01-22 21:40 ` patchwork-bot+linux-arm-msm
2 siblings, 0 replies; 4+ messages in thread
From: Robert Marko @ 2020-11-04 13:44 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, robh+dt, linux-arm-msm, devicetree,
linux-kernel
Cc: John Crispin, Luka Perkov, Vinod Koul
On Wed, Sep 9, 2020 at 6:38 PM Robert Marko <robert.marko@sartura.hr> wrote:
>
> From: John Crispin <john@phrozen.org>
>
> Since we now have driver for the USB PHY, and USB controller is already supported by the DWC3 driver lets add the necessary nodes to DTSI.
>
> Signed-off-by: John Crispin <john@phrozen.org>
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> Cc: Luka Perkov <luka.perkov@sartura.hr>
> Reviewed-by: Vinod Koul <vkoul@kernel.org>
> ---
> Changes from v7 to v8:
> * Add labels for usb2 and usb3 nodes
> Changes from v6 to v7:
> * Remove changes to qcom-ipq4019-ap.dk01.1.dtsi
> It has slipped in unwanted, we only want to add
> nodes to the DTSI.
>
> arch/arm/boot/dts/qcom-ipq4019.dtsi | 74 +++++++++++++++++++++++++++++
> 1 file changed, 74 insertions(+)
>
> diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
> index 74d8e2c8e4b3..4a973253024a 100644
> --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
> +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
> @@ -605,5 +605,79 @@ ethphy4: ethernet-phy@4 {
> reg = <4>;
> };
> };
> +
> + usb3_ss_phy: ssphy@9a000 {
> + compatible = "qcom,usb-ss-ipq4019-phy";
> + #phy-cells = <0>;
> + reg = <0x9a000 0x800>;
> + reg-names = "phy_base";
> + resets = <&gcc USB3_UNIPHY_PHY_ARES>;
> + reset-names = "por_rst";
> + status = "disabled";
> + };
> +
> + usb3_hs_phy: hsphy@a6000 {
> + compatible = "qcom,usb-hs-ipq4019-phy";
> + #phy-cells = <0>;
> + reg = <0xa6000 0x40>;
> + reg-names = "phy_base";
> + resets = <&gcc USB3_HSPHY_POR_ARES>, <&gcc USB3_HSPHY_S_ARES>;
> + reset-names = "por_rst", "srif_rst";
> + status = "disabled";
> + };
> +
> + usb3: usb3@8af8800 {
> + compatible = "qcom,dwc3";
> + reg = <0x8af8800 0x100>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + clocks = <&gcc GCC_USB3_MASTER_CLK>,
> + <&gcc GCC_USB3_SLEEP_CLK>,
> + <&gcc GCC_USB3_MOCK_UTMI_CLK>;
> + clock-names = "master", "sleep", "mock_utmi";
> + ranges;
> + status = "disabled";
> +
> + dwc3@8a00000 {
> + compatible = "snps,dwc3";
> + reg = <0x8a00000 0xf8000>;
> + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&usb3_hs_phy>, <&usb3_ss_phy>;
> + phy-names = "usb2-phy", "usb3-phy";
> + dr_mode = "host";
> + };
> + };
> +
> + usb2_hs_phy: hsphy@a8000 {
> + compatible = "qcom,usb-hs-ipq4019-phy";
> + #phy-cells = <0>;
> + reg = <0xa8000 0x40>;
> + reg-names = "phy_base";
> + resets = <&gcc USB2_HSPHY_POR_ARES>, <&gcc USB2_HSPHY_S_ARES>;
> + reset-names = "por_rst", "srif_rst";
> + status = "disabled";
> + };
> +
> + usb2: usb2@60f8800 {
> + compatible = "qcom,dwc3";
> + reg = <0x60f8800 0x100>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + clocks = <&gcc GCC_USB2_MASTER_CLK>,
> + <&gcc GCC_USB2_SLEEP_CLK>,
> + <&gcc GCC_USB2_MOCK_UTMI_CLK>;
> + clock-names = "master", "sleep", "mock_utmi";
> + ranges;
> + status = "disabled";
> +
> + dwc3@6000000 {
> + compatible = "snps,dwc3";
> + reg = <0x6000000 0xf8000>;
> + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&usb2_hs_phy>;
> + phy-names = "usb2-phy";
> + dr_mode = "host";
> + };
> + };
> };
> };
> --
> 2.26.2
Hi,
Any chance of reviewing this?
Regards,
Robert
>
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH v8] ARM: dts: qcom: ipq4019: add USB devicetree nodes
2020-09-09 16:38 [PATCH v8] ARM: dts: qcom: ipq4019: add USB devicetree nodes Robert Marko
2020-10-02 17:39 ` Robert Marko
2020-11-04 13:44 ` Robert Marko
@ 2021-01-22 21:40 ` patchwork-bot+linux-arm-msm
2 siblings, 0 replies; 4+ messages in thread
From: patchwork-bot+linux-arm-msm @ 2021-01-22 21:40 UTC (permalink / raw)
To: Robert Marko; +Cc: linux-arm-msm
Hello:
This patch was applied to qcom/linux.git (refs/heads/for-next):
On Wed, 9 Sep 2020 18:38:31 +0200 you wrote:
> From: John Crispin <john@phrozen.org>
>
> Since we now have driver for the USB PHY, and USB controller is already supported by the DWC3 driver lets add the necessary nodes to DTSI.
>
> Signed-off-by: John Crispin <john@phrozen.org>
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> Cc: Luka Perkov <luka.perkov@sartura.hr>
> Reviewed-by: Vinod Koul <vkoul@kernel.org>
>
> [...]
Here is the summary with links:
- [v8] ARM: dts: qcom: ipq4019: add USB devicetree nodes
https://git.kernel.org/qcom/c/b8afc254b401
You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2021-01-22 21:41 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-09-09 16:38 [PATCH v8] ARM: dts: qcom: ipq4019: add USB devicetree nodes Robert Marko
2020-10-02 17:39 ` Robert Marko
2020-11-04 13:44 ` Robert Marko
2021-01-22 21:40 ` patchwork-bot+linux-arm-msm
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.