[PATCH V3 0/2] MFD and GPIO for STA2X11

[PATCH V3 0/2] MFD and GPIO for STA2X11

[Alessandro Rubini]

These two patches introduce the multi-function device and GPIO support for
the STA2X11 I/O Hub.  Core PCI support is already in linux-next.

V1: sent on Jan 26th as RFC and got no comments back

V2: sent on Feb 16th, fixed a number of minor details, got comments from
Linus Walleij and Samuel Ortiz.

V3: accepted all suggestions.  I delayed this resending a while because
I hoped the base STA2X11 patches to be accepted, but despite the positive
comments I got on those patches, they are not in linux-next as of today

This set, thus, refers to CONFIG_STA2X11 which is not yet upstream.linux-next.

Like in V2, I Cc'd both patches to all interested parties, because
the MFD patch must be fore the GPIO one, so they're better merged to
the same tree.

Alessandro Rubini (2):
  mfd: Add driver for STA2X11 MFD block
  gpio: add STA2X11 GPIO block

 arch/x86/include/asm/sta2x11.h  |   12 +
 drivers/gpio/Kconfig            |    8 +
 drivers/gpio/Makefile           |    1 +
 drivers/gpio/gpio-sta2x11.c     |  435 ++++++++++++++++++++++++++++++++++++
 drivers/mfd/Kconfig             |    6 +
 drivers/mfd/Makefile            |    1 +
 drivers/mfd/sta2x11-mfd.c       |  467 +++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/sta2x11-mfd.h |  324 +++++++++++++++++++++++++++
 8 files changed, 1254 insertions(+), 0 deletions(-)
 create mode 100644 arch/x86/include/asm/sta2x11.h
 create mode 100644 drivers/gpio/gpio-sta2x11.c
 create mode 100644 drivers/mfd/sta2x11-mfd.c
 create mode 100644 include/linux/mfd/sta2x11-mfd.h

-- 
1.7.7.2

[PATCH V3 1/2] mfd: Add driver for STA2X11 MFD block

[Alessandro Rubini]

This also introduces <asm/sta2x11.h> to export a function that is in
the base sta2x11 support patches. The header will increase with other
prototypes and constants over time.

Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
---
 arch/x86/include/asm/sta2x11.h  |   12 +
 drivers/mfd/Kconfig             |    6 +
 drivers/mfd/Makefile            |    1 +
 drivers/mfd/sta2x11-mfd.c       |  467 +++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/sta2x11-mfd.h |  324 +++++++++++++++++++++++++++
 5 files changed, 810 insertions(+), 0 deletions(-)
 create mode 100644 arch/x86/include/asm/sta2x11.h
 create mode 100644 drivers/mfd/sta2x11-mfd.c
 create mode 100644 include/linux/mfd/sta2x11-mfd.h

diff --git a/arch/x86/include/asm/sta2x11.h b/arch/x86/include/asm/sta2x11.h
new file mode 100644
index 0000000..e9d32df
--- /dev/null
+++ b/arch/x86/include/asm/sta2x11.h
@@ -0,0 +1,12 @@
+/*
+ * Header file for STMicroelectronics ConneXt (STA2X11) IOHub
+ */
+#ifndef __ASM_STA2X11_H
+#define __ASM_STA2X11_H
+
+#include <linux/pci.h>
+
+/* This needs to be called from the MFD to configure its sub-devices */
+struct sta2x11_instance *sta2x11_get_instance(struct pci_dev *pdev);
+
+#endif /* __ASM_STA2X11_H */
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 29f463c..c194c67 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -873,6 +873,12 @@ config MFD_RC5T583
 	  Additional drivers must be enabled in order to use the
 	  different functionality of the device.
 
+config MFD_STA2X11
+	bool "STA2X11 multi function device support"
+	depends on STA2X11
+	select MFD_CORE
+	select GPIO_STA2X11
+
 config MFD_ANATOP
 	bool "Support for Freescale i.MX on-chip ANATOP controller"
 	depends on SOC_IMX6Q
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 05fa538..7cd8f02 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_MFD_DAVINCI_VOICECODEC)	+= davinci_voicecodec.o
 obj-$(CONFIG_MFD_DM355EVM_MSP)	+= dm355evm_msp.o
 obj-$(CONFIG_MFD_TI_SSP)	+= ti-ssp.o
 
+obj-$(CONFIG_MFD_STA2X11)	+= sta2x11-mfd.o
 obj-$(CONFIG_MFD_STMPE)		+= stmpe.o
 obj-$(CONFIG_STMPE_I2C)		+= stmpe-i2c.o
 obj-$(CONFIG_STMPE_SPI)		+= stmpe-spi.o
diff --git a/drivers/mfd/sta2x11-mfd.c b/drivers/mfd/sta2x11-mfd.c
new file mode 100644
index 0000000..14a79e6
--- /dev/null
+++ b/drivers/mfd/sta2x11-mfd.c
@@ -0,0 +1,467 @@
+/*
+ * Copyright (c) 2009-2011 Wind River Systems, Inc.
+ * Copyright (c) 2011 ST Microelectronics (Alessandro Rubini)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ * See the GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/errno.h>
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <linux/list.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/pci.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/sta2x11-mfd.h>
+
+#include <asm/sta2x11.h>
+
+/* This describes STA2X11 MFD chip for us, we may have several */
+struct sta2x11_mfd {
+	struct sta2x11_instance *instance;
+	spinlock_t lock;
+	struct list_head list;
+	void __iomem *sctl_regs;
+	void __iomem *apbreg_regs;
+};
+
+static LIST_HEAD(sta2x11_mfd_list);
+
+/* Three functions to act on the list */
+static struct sta2x11_mfd *sta2x11_mfd_find(struct pci_dev *pdev)
+{
+	struct sta2x11_instance *instance;
+	struct sta2x11_mfd *mfd;
+
+	if (!pdev && !list_empty(&sta2x11_mfd_list)) {
+		pr_warning("%s: Unspecified device, "
+			    "using first instance\n", __func__);
+		return list_entry(sta2x11_mfd_list.next,
+				  struct sta2x11_mfd, list);
+	}
+
+	instance = sta2x11_get_instance(pdev);
+	if (!instance)
+		return NULL;
+	list_for_each_entry(mfd, &sta2x11_mfd_list, list) {
+		if (mfd->instance == instance)
+			return mfd;
+	}
+	return NULL;
+}
+
+static int __devinit sta2x11_mfd_add(struct pci_dev *pdev, gfp_t flags)
+{
+	struct sta2x11_mfd *mfd = sta2x11_mfd_find(pdev);
+	struct sta2x11_instance *instance;
+
+	if (mfd)
+		return -EBUSY;
+	instance = sta2x11_get_instance(pdev);
+	if (!instance)
+		return -EINVAL;
+	mfd = kzalloc(sizeof(*mfd), flags);
+	if (!mfd)
+		return -ENOMEM;
+	INIT_LIST_HEAD(&mfd->list);
+	spin_lock_init(&mfd->lock);
+	mfd->instance = instance;
+	list_add(&mfd->list, &sta2x11_mfd_list);
+	return 0;
+}
+
+static int __devexit mfd_remove(struct pci_dev *pdev)
+{
+	struct sta2x11_mfd *mfd = sta2x11_mfd_find(pdev);
+
+	if (!mfd)
+		return -ENODEV;
+	list_del(&mfd->list);
+	kfree(mfd);
+	return 0;
+}
+
+/* These two functions are exported and are not expected to fail */
+u32 sta2x11_sctl_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val)
+{
+	struct sta2x11_mfd *mfd = sta2x11_mfd_find(pdev);
+	u32 r;
+	unsigned long flags;
+
+	if (!mfd) {
+		dev_warn(&pdev->dev, ": can't access sctl regs\n");
+		return 0;
+	}
+	if (!mfd->sctl_regs) {
+		dev_warn(&pdev->dev, ": system ctl not initialized\n");
+		return 0;
+	}
+	spin_lock_irqsave(&mfd->lock, flags);
+	r = readl(mfd->sctl_regs + reg);
+	r &= ~mask;
+	r |= val;
+	if (mask)
+		writel(r, mfd->sctl_regs + reg);
+	spin_unlock_irqrestore(&mfd->lock, flags);
+	return r;
+}
+EXPORT_SYMBOL(sta2x11_sctl_mask);
+
+u32 sta2x11_apbreg_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val)
+{
+	struct sta2x11_mfd *mfd = sta2x11_mfd_find(pdev);
+	u32 r;
+	unsigned long flags;
+
+	if (!mfd) {
+		dev_warn(&pdev->dev, ": can't access apb regs\n");
+		return 0;
+	}
+	if (!mfd->apbreg_regs) {
+		dev_warn(&pdev->dev, ": apb bridge not initialized\n");
+		return 0;
+	}
+	spin_lock_irqsave(&mfd->lock, flags);
+	r = readl(mfd->apbreg_regs + reg);
+	r &= ~mask;
+	r |= val;
+	if (mask)
+		writel(r, mfd->apbreg_regs + reg);
+	spin_unlock_irqrestore(&mfd->lock, flags);
+	return r;
+}
+EXPORT_SYMBOL(sta2x11_apbreg_mask);
+
+/* Two debugfs files, for our registers (FIXME: one instance only) */
+#define REG(regname) {.name = #regname, .offset = SCTL_ ## regname}
+static struct debugfs_reg32 sta2x11_sctl_regs[] = {
+	REG(SCCTL), REG(ARMCFG), REG(SCPLLCTL), REG(SCPLLFCTRL),
+	REG(SCRESFRACT), REG(SCRESCTRL1), REG(SCRESXTRL2), REG(SCPEREN0),
+	REG(SCPEREN1), REG(SCPEREN2), REG(SCGRST), REG(SCPCIPMCR1),
+	REG(SCPCIPMCR2), REG(SCPCIPMSR1), REG(SCPCIPMSR2), REG(SCPCIPMSR3),
+	REG(SCINTREN), REG(SCRISR), REG(SCCLKSTAT0), REG(SCCLKSTAT1),
+	REG(SCCLKSTAT2), REG(SCRSTSTA),
+};
+#undef REG
+
+static struct debugfs_regset32 sctl_regset = {
+	.regs = sta2x11_sctl_regs,
+	.nregs = ARRAY_SIZE(sta2x11_sctl_regs),
+};
+
+#define REG(regname) {.name = #regname, .offset = regname}
+static struct debugfs_reg32 sta2x11_apbreg_regs[] = {
+	REG(APBREG_BSR), REG(APBREG_PAER), REG(APBREG_PWAC), REG(APBREG_PRAC),
+	REG(APBREG_PCG), REG(APBREG_PUR), REG(APBREG_EMU_PCG),
+};
+#undef REG
+
+static struct debugfs_regset32 apbreg_regset = {
+	.regs = sta2x11_apbreg_regs,
+	.nregs = ARRAY_SIZE(sta2x11_apbreg_regs),
+};
+
+static struct dentry *sta2x11_sctl_debugfs;
+static struct dentry *sta2x11_apbreg_debugfs;
+
+/* Probe for the two platform devices */
+static int sta2x11_sctl_probe(struct platform_device *dev)
+{
+	struct pci_dev **pdev;
+	struct sta2x11_mfd *mfd;
+	struct resource *res;
+
+	pdev = dev->dev.platform_data;
+	mfd = sta2x11_mfd_find(*pdev);
+	if (!mfd)
+		return -ENODEV;
+
+	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENOMEM;
+
+	if (!request_mem_region(res->start, resource_size(res),
+				"sta2x11-sctl"))
+		return -EBUSY;
+
+	mfd->sctl_regs = ioremap(res->start, resource_size(res));
+	if (!mfd->sctl_regs) {
+		release_mem_region(res->start, resource_size(res));
+		return -ENOMEM;
+	}
+	sctl_regset.base = mfd->sctl_regs;
+	sta2x11_sctl_debugfs = debugfs_create_regset32("sta2x11-sctl",
+						  S_IFREG | S_IRUGO,
+						  NULL, &sctl_regset);
+	return 0;
+}
+
+static int sta2x11_apbreg_probe(struct platform_device *dev)
+{
+	struct pci_dev **pdev;
+	struct sta2x11_mfd *mfd;
+	struct resource *res;
+
+	pdev = dev->dev.platform_data;
+	dev_dbg(&dev->dev, "%s: pdata is %p\n", __func__, pdev);
+	dev_dbg(&dev->dev, "%s: *pdata is %p\n", __func__, *pdev);
+
+	mfd = sta2x11_mfd_find(*pdev);
+	if (!mfd)
+		return -ENODEV;
+
+	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENOMEM;
+
+	if (!request_mem_region(res->start, resource_size(res),
+				"sta2x11-apbreg"))
+		return -EBUSY;
+
+	mfd->apbreg_regs = ioremap(res->start, resource_size(res));
+	if (!mfd->apbreg_regs) {
+		release_mem_region(res->start, resource_size(res));
+		return -ENOMEM;
+	}
+	dev_dbg(&dev->dev, "%s: regbase %p\n", __func__, mfd->apbreg_regs);
+
+	apbreg_regset.base = mfd->apbreg_regs;
+	sta2x11_apbreg_debugfs = debugfs_create_regset32("sta2x11-apbreg",
+						  S_IFREG | S_IRUGO,
+						  NULL, &apbreg_regset);
+	return 0;
+}
+
+/* The two platform drivers */
+static struct platform_driver sta2x11_sctl_platform_driver = {
+	.driver = {
+		.name	= "sta2x11-sctl",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= sta2x11_sctl_probe,
+};
+
+static int __init sta2x11_sctl_init(void)
+{
+	pr_info("%s\n", __func__);
+	return platform_driver_register(&sta2x11_sctl_platform_driver);
+}
+
+static struct platform_driver sta2x11_platform_driver = {
+	.driver = {
+		.name	= "sta2x11-apbreg",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= sta2x11_apbreg_probe,
+};
+
+static int __init sta2x11_apbreg_init(void)
+{
+	pr_info("%s\n", __func__);
+	return platform_driver_register(&sta2x11_platform_driver);
+}
+
+/*
+ * What follows is the PCI device that hosts the above two pdevs.
+ * Each logic block is 4kB and they are all consecutive: we use this info.
+ */
+
+/* Bar 0 */
+enum bar0_cells {
+	GPIO_0 = 0,
+	GPIO_1,
+	GPIO_2,
+	GPIO_3,
+	SCTL,
+	SCR,
+	TIME,
+};
+/* Bar 1 */
+enum bar1_cells {
+	APBREG = 0,
+};
+#define CELL_4K(_name, _cell) { \
+		.name = _name, \
+		.start = _cell * 4096, .end = _cell * 4096 + 4095, \
+		.flags = IORESOURCE_MEM, \
+		}
+
+static const __devinitconst struct resource gpio_resources[] = {
+	{
+		.name = "sta2x11_gpio", /* 4 consecutive cells, 1 driver */
+		.start = 0,
+		.end = (4 * 4096) - 1,
+		.flags = IORESOURCE_MEM,
+	}
+};
+static const __devinitconst struct resource sctl_resources[] = {
+	CELL_4K("sta2x11-sctl", SCTL),
+};
+static const __devinitconst struct resource scr_resources[] = {
+	CELL_4K("sta2x11-scr", SCR),
+};
+static const __devinitconst struct resource time_resources[] = {
+	CELL_4K("sta2x11-time", TIME),
+};
+
+static const __devinitconst struct resource apbreg_resources[] = {
+	CELL_4K("sta2x11-apbreg", APBREG),
+};
+
+#define DEV(_name, _r) \
+	{ .name = _name, .num_resources = ARRAY_SIZE(_r), .resources = _r, }
+
+static __devinitdata struct mfd_cell sta2x11_mfd_bar0[] = {
+	DEV("sta2x11-gpio", gpio_resources), /* offset 0: we add pdata later */
+	DEV("sta2x11-sctl", sctl_resources),
+	DEV("sta2x11-scr", scr_resources),
+	DEV("sta2x11-time", time_resources),
+};
+
+static __devinitdata struct mfd_cell sta2x11_mfd_bar1[] = {
+	DEV("sta2x11-apbreg", apbreg_resources),
+};
+
+static int sta2x11_mfd_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+	pci_save_state(pdev);
+	pci_disable_device(pdev);
+	pci_set_power_state(pdev, pci_choose_state(pdev, state));
+
+	return 0;
+}
+
+static int sta2x11_mfd_resume(struct pci_dev *pdev)
+{
+	int err;
+
+	pci_set_power_state(pdev, 0);
+	err = pci_enable_device(pdev);
+	if (err)
+		return err;
+	pci_restore_state(pdev);
+
+	return 0;
+}
+
+static int __devinit sta2x11_mfd_probe(struct pci_dev *pdev,
+				       const struct pci_device_id *pci_id)
+{
+	int err, i;
+	struct sta2x11_gpio_pdata *gpio_data;
+
+	dev_info(&pdev->dev, "%s\n", __func__);
+
+	err = pci_enable_device(pdev);
+	if (err) {
+		dev_err(&pdev->dev, "Can't enable device.\n");
+		return err;
+	}
+
+	err = pci_enable_msi(pdev);
+	if (err)
+		dev_info(&pdev->dev, "Enable msi failed\n");
+
+	/* Read gpio config data as pci device's platform data */
+	gpio_data = dev_get_platdata(&pdev->dev);
+	if (!gpio_data)
+		dev_warn(&pdev->dev, "no gpio configuration\n");
+
+	dev_dbg(&pdev->dev, "%s, gpio_data = %p (%p)\n", __func__,
+		gpio_data, &gpio_data);
+	dev_dbg(&pdev->dev, "%s, pdev = %p (%p)\n", __func__,
+		pdev, &pdev);
+
+	/* platform data is the pci device for all of them */
+	for (i = 0; i < ARRAY_SIZE(sta2x11_mfd_bar0); i++) {
+		sta2x11_mfd_bar0[i].pdata_size = sizeof(pdev);
+		sta2x11_mfd_bar0[i].platform_data = &pdev;
+	}
+	sta2x11_mfd_bar1[0].pdata_size = sizeof(pdev);
+	sta2x11_mfd_bar1[0].platform_data = &pdev;
+
+	/* Record this pdev before mfd_add_devices: their probe looks for it */
+	sta2x11_mfd_add(pdev, GFP_ATOMIC);
+
+
+	err = mfd_add_devices(&pdev->dev, -1,
+			      sta2x11_mfd_bar0,
+			      ARRAY_SIZE(sta2x11_mfd_bar0),
+			      &pdev->resource[0],
+			      0);
+	if (err) {
+		dev_err(&pdev->dev, "mfd_add_devices[0] failed: %d\n", err);
+		goto err_disable;
+	}
+
+	err = mfd_add_devices(&pdev->dev, -1,
+			      sta2x11_mfd_bar1,
+			      ARRAY_SIZE(sta2x11_mfd_bar1),
+			      &pdev->resource[1],
+			      0);
+	if (err) {
+		dev_err(&pdev->dev, "mfd_add_devices[1] failed: %d\n", err);
+		goto err_disable;
+	}
+
+	return 0;
+
+err_disable:
+	mfd_remove_devices(&pdev->dev);
+	pci_disable_device(pdev);
+	pci_disable_msi(pdev);
+	return err;
+}
+
+static DEFINE_PCI_DEVICE_TABLE(sta2x11_mfd_tbl) = {
+	{PCI_DEVICE(PCI_VENDOR_ID_STMICRO, PCI_DEVICE_ID_STMICRO_GPIO)},
+	{0,},
+};
+
+static struct pci_driver sta2x11_mfd_driver = {
+	.name =		"sta2x11-mfd",
+	.id_table =	sta2x11_mfd_tbl,
+	.probe =	sta2x11_mfd_probe,
+	.suspend =	sta2x11_mfd_suspend,
+	.resume =	sta2x11_mfd_resume,
+};
+
+static int __init sta2x11_mfd_init(void)
+{
+	pr_info("%s\n", __func__);
+	return pci_register_driver(&sta2x11_mfd_driver);
+}
+
+/*
+ * All of this must be ready before "normal" devices like MMCI appear.
+ * But MFD (the pci device) can't be too early. The following choice
+ * prepares platform drivers very early and probe the PCI device later,
+ * but before other PCI devices.
+ */
+subsys_initcall(sta2x11_apbreg_init);
+subsys_initcall(sta2x11_sctl_init);
+rootfs_initcall(sta2x11_mfd_init);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Wind River");
+MODULE_DESCRIPTION("STA2x11 mfd for GPIO, SCTL and APBREG");
+MODULE_DEVICE_TABLE(pci, sta2x11_mfd_tbl);
diff --git a/include/linux/mfd/sta2x11-mfd.h b/include/linux/mfd/sta2x11-mfd.h
new file mode 100644
index 0000000..d179227
--- /dev/null
+++ b/include/linux/mfd/sta2x11-mfd.h
@@ -0,0 +1,324 @@
+/*
+ * Copyright (c) 2009-2011 Wind River Systems, Inc.
+ * Copyright (c) 2011 ST Microelectronics (Alessandro Rubini)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ * See the GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * The STMicroelectronics ConneXt (STA2X11) chip has several unrelated
+ * functions in one PCI endpoint functions. This driver simply
+ * registers the platform devices in this iomemregion and exports a few
+ * functions to access common registers
+ */
+
+#ifndef __STA2X11_MFD_H
+#define __STA2X11_MFD_H
+#include <linux/types.h>
+#include <linux/pci.h>
+
+/*
+ * The MFD PCI block includes the GPIO peripherals and other register blocks.
+ * For GPIO, we have 32*4 bits (I use "gsta" for "gpio sta2x11".)
+ */
+#define GSTA_GPIO_PER_BLOCK	32
+#define GSTA_NR_BLOCKS		4
+#define GSTA_NR_GPIO		(GSTA_GPIO_PER_BLOCK * GSTA_NR_BLOCKS)
+
+/* Pinconfig is set by the board definition: altfunc, pull-up, pull-down */
+struct sta2x11_gpio_pdata {
+	unsigned pinconfig[GSTA_NR_GPIO];
+};
+
+/* Macros below lifted from sh_pfc.h, with minor differences */
+#define PINMUX_TYPE_NONE		0
+#define PINMUX_TYPE_FUNCTION		1
+#define PINMUX_TYPE_OUTPUT_LOW		2
+#define PINMUX_TYPE_OUTPUT_HIGH		3
+#define PINMUX_TYPE_INPUT		4
+#define PINMUX_TYPE_INPUT_PULLUP	5
+#define PINMUX_TYPE_INPUT_PULLDOWN	6
+
+/* Give names to GPIO pins, like PXA does, taken from the manual */
+#define STA2X11_GPIO0			0
+#define STA2X11_GPIO1			1
+#define STA2X11_GPIO2			2
+#define STA2X11_GPIO3			3
+#define STA2X11_GPIO4			4
+#define STA2X11_GPIO5			5
+#define STA2X11_GPIO6			6
+#define STA2X11_GPIO7			7
+#define STA2X11_GPIO8_RGBOUT_RED7	8
+#define STA2X11_GPIO9_RGBOUT_RED6	9
+#define STA2X11_GPIO10_RGBOUT_RED5	10
+#define STA2X11_GPIO11_RGBOUT_RED4	11
+#define STA2X11_GPIO12_RGBOUT_RED3	12
+#define STA2X11_GPIO13_RGBOUT_RED2	13
+#define STA2X11_GPIO14_RGBOUT_RED1	14
+#define STA2X11_GPIO15_RGBOUT_RED0	15
+#define STA2X11_GPIO16_RGBOUT_GREEN7	16
+#define STA2X11_GPIO17_RGBOUT_GREEN6	17
+#define STA2X11_GPIO18_RGBOUT_GREEN5	18
+#define STA2X11_GPIO19_RGBOUT_GREEN4	19
+#define STA2X11_GPIO20_RGBOUT_GREEN3	20
+#define STA2X11_GPIO21_RGBOUT_GREEN2	21
+#define STA2X11_GPIO22_RGBOUT_GREEN1	22
+#define STA2X11_GPIO23_RGBOUT_GREEN0	23
+#define STA2X11_GPIO24_RGBOUT_BLUE7	24
+#define STA2X11_GPIO25_RGBOUT_BLUE6	25
+#define STA2X11_GPIO26_RGBOUT_BLUE5	26
+#define STA2X11_GPIO27_RGBOUT_BLUE4	27
+#define STA2X11_GPIO28_RGBOUT_BLUE3	28
+#define STA2X11_GPIO29_RGBOUT_BLUE2	29
+#define STA2X11_GPIO30_RGBOUT_BLUE1	30
+#define STA2X11_GPIO31_RGBOUT_BLUE0	31
+#define STA2X11_GPIO32_RGBOUT_VSYNCH	32
+#define STA2X11_GPIO33_RGBOUT_HSYNCH	33
+#define STA2X11_GPIO34_RGBOUT_DEN	34
+#define STA2X11_GPIO35_ETH_CRS_DV	35
+#define STA2X11_GPIO36_ETH_TXD1		36
+#define STA2X11_GPIO37_ETH_TXD0		37
+#define STA2X11_GPIO38_ETH_TX_EN	38
+#define STA2X11_GPIO39_MDIO		39
+#define STA2X11_GPIO40_ETH_REF_CLK	40
+#define STA2X11_GPIO41_ETH_RXD1		41
+#define STA2X11_GPIO42_ETH_RXD0		42
+#define STA2X11_GPIO43_MDC		43
+#define STA2X11_GPIO44_CAN_TX		44
+#define STA2X11_GPIO45_CAN_RX		45
+#define STA2X11_GPIO46_MLB_DAT		46
+#define STA2X11_GPIO47_MLB_SIG		47
+#define STA2X11_GPIO48_SPI0_CLK		48
+#define STA2X11_GPIO49_SPI0_TXD		49
+#define STA2X11_GPIO50_SPI0_RXD		50
+#define STA2X11_GPIO51_SPI0_FRM		51
+#define STA2X11_GPIO52_SPI1_CLK		52
+#define STA2X11_GPIO53_SPI1_TXD		53
+#define STA2X11_GPIO54_SPI1_RXD		54
+#define STA2X11_GPIO55_SPI1_FRM		55
+#define STA2X11_GPIO56_SPI2_CLK		56
+#define STA2X11_GPIO57_SPI2_TXD		57
+#define STA2X11_GPIO58_SPI2_RXD		58
+#define STA2X11_GPIO59_SPI2_FRM		59
+#define STA2X11_GPIO60_I2C0_SCL		60
+#define STA2X11_GPIO61_I2C0_SDA		61
+#define STA2X11_GPIO62_I2C1_SCL		62
+#define STA2X11_GPIO63_I2C1_SDA		63
+#define STA2X11_GPIO64_I2C2_SCL		64
+#define STA2X11_GPIO65_I2C2_SDA		65
+#define STA2X11_GPIO66_I2C3_SCL		66
+#define STA2X11_GPIO67_I2C3_SDA		67
+#define STA2X11_GPIO68_MSP0_RCK		68
+#define STA2X11_GPIO69_MSP0_RXD		69
+#define STA2X11_GPIO70_MSP0_RFS		70
+#define STA2X11_GPIO71_MSP0_TCK		71
+#define STA2X11_GPIO72_MSP0_TXD		72
+#define STA2X11_GPIO73_MSP0_TFS		73
+#define STA2X11_GPIO74_MSP0_SCK		74
+#define STA2X11_GPIO75_MSP1_CK		75
+#define STA2X11_GPIO76_MSP1_RXD		76
+#define STA2X11_GPIO77_MSP1_FS		77
+#define STA2X11_GPIO78_MSP1_TXD		78
+#define STA2X11_GPIO79_MSP2_CK		79
+#define STA2X11_GPIO80_MSP2_RXD		80
+#define STA2X11_GPIO81_MSP2_FS		81
+#define STA2X11_GPIO82_MSP2_TXD		82
+#define STA2X11_GPIO83_MSP3_CK		83
+#define STA2X11_GPIO84_MSP3_RXD		84
+#define STA2X11_GPIO85_MSP3_FS		85
+#define STA2X11_GPIO86_MSP3_TXD		86
+#define STA2X11_GPIO87_MSP4_CK		87
+#define STA2X11_GPIO88_MSP4_RXD		88
+#define STA2X11_GPIO89_MSP4_FS		89
+#define STA2X11_GPIO90_MSP4_TXD		90
+#define STA2X11_GPIO91_MSP5_CK		91
+#define STA2X11_GPIO92_MSP5_RXD		92
+#define STA2X11_GPIO93_MSP5_FS		93
+#define STA2X11_GPIO94_MSP5_TXD		94
+#define STA2X11_GPIO95_SDIO3_DAT3	95
+#define STA2X11_GPIO96_SDIO3_DAT2	96
+#define STA2X11_GPIO97_SDIO3_DAT1	97
+#define STA2X11_GPIO98_SDIO3_DAT0	98
+#define STA2X11_GPIO99_SDIO3_CLK	99
+#define STA2X11_GPIO100_SDIO3_CMD	100
+#define STA2X11_GPIO101			101
+#define STA2X11_GPIO102			102
+#define STA2X11_GPIO103			103
+#define STA2X11_GPIO104			104
+#define STA2X11_GPIO105_SDIO2_DAT3	105
+#define STA2X11_GPIO106_SDIO2_DAT2	106
+#define STA2X11_GPIO107_SDIO2_DAT1	107
+#define STA2X11_GPIO108_SDIO2_DAT0	108
+#define STA2X11_GPIO109_SDIO2_CLK	109
+#define STA2X11_GPIO110_SDIO2_CMD	110
+#define STA2X11_GPIO111			111
+#define STA2X11_GPIO112			112
+#define STA2X11_GPIO113			113
+#define STA2X11_GPIO114			114
+#define STA2X11_GPIO115_SDIO1_DAT3	115
+#define STA2X11_GPIO116_SDIO1_DAT2	116
+#define STA2X11_GPIO117_SDIO1_DAT1	117
+#define STA2X11_GPIO118_SDIO1_DAT0	118
+#define STA2X11_GPIO119_SDIO1_CLK	119
+#define STA2X11_GPIO120_SDIO1_CMD	120
+#define STA2X11_GPIO121			121
+#define STA2X11_GPIO122			122
+#define STA2X11_GPIO123			123
+#define STA2X11_GPIO124			124
+#define STA2X11_GPIO125_UART2_TXD	125
+#define STA2X11_GPIO126_UART2_RXD	126
+#define STA2X11_GPIO127_UART3_TXD	127
+
+/*
+ * The APB bridge has its own registers, needed by our users as well.
+ * They are accessed with the following read/mask/write function.
+ */
+u32 sta2x11_apbreg_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val);
+
+/* CAN and MLB */
+#define APBREG_BSR	0x00	/* Bridge Status Reg */
+#define APBREG_PAER	0x08	/* Peripherals Address Error Reg */
+#define APBREG_PWAC	0x20	/* Peripheral Write Access Control reg */
+#define APBREG_PRAC	0x40	/* Peripheral Read Access Control reg */
+#define APBREG_PCG	0x60	/* Peripheral Clock Gating Reg */
+#define APBREG_PUR	0x80	/* Peripheral Under Reset Reg */
+#define APBREG_EMU_PCG	0xA0	/* Emulator Peripheral Clock Gating Reg */
+
+#define APBREG_CAN	(1 << 1)
+#define APBREG_MLB	(1 << 3)
+
+/* SARAC */
+#define APBREG_BSR_SARAC     0x100 /* Bridge Status Reg */
+#define APBREG_PAER_SARAC    0x108 /* Peripherals Address Error Reg */
+#define APBREG_PWAC_SARAC    0x120 /* Peripheral Write Access Control reg */
+#define APBREG_PRAC_SARAC    0x140 /* Peripheral Read Access Control reg */
+#define APBREG_PCG_SARAC     0x160 /* Peripheral Clock Gating Reg */
+#define APBREG_PUR_SARAC     0x180 /* Peripheral Under Reset Reg */
+#define APBREG_EMU_PCG_SARAC 0x1A0 /* Emulator Peripheral Clock Gating Reg */
+
+#define APBREG_SARAC	(1 << 2)
+
+/*
+ * The system controller has its own registers. Some of these are accessed
+ * by out users as well, using the following read/mask/write/function
+ */
+u32 sta2x11_sctl_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val);
+
+#define SCTL_SCCTL		0x00	/* System controller control register */
+#define SCTL_ARMCFG		0x04	/* ARM configuration register */
+#define SCTL_SCPLLCTL		0x08	/* PLL control status register */
+#define SCTL_SCPLLFCTRL		0x0c	/* PLL frequency control register */
+#define SCTL_SCRESFRACT		0x10	/* PLL fractional input register */
+#define SCTL_SCRESCTRL1		0x14	/* Peripheral reset control 1 */
+#define SCTL_SCRESXTRL2		0x18	/* Peripheral reset control 2 */
+#define SCTL_SCPEREN0		0x1c	/* Peripheral clock enable register 0 */
+#define SCTL_SCPEREN1		0x20	/* Peripheral clock enable register 1 */
+#define SCTL_SCPEREN2		0x24	/* Peripheral clock enable register 2 */
+#define SCTL_SCGRST		0x28	/* Peripheral global reset */
+#define SCTL_SCPCIPMCR1		0x30	/* PCI power management control 1 */
+#define SCTL_SCPCIPMCR2		0x34	/* PCI power management control 2 */
+#define SCTL_SCPCIPMSR1		0x38	/* PCI power management status 1 */
+#define SCTL_SCPCIPMSR2		0x3c	/* PCI power management status 2 */
+#define SCTL_SCPCIPMSR3		0x40	/* PCI power management status 3 */
+#define SCTL_SCINTREN		0x44	/* Interrupt enable */
+#define SCTL_SCRISR		0x48	/* RAW interrupt status */
+#define SCTL_SCCLKSTAT0		0x4c	/* Peripheral clocks status 0 */
+#define SCTL_SCCLKSTAT1		0x50	/* Peripheral clocks status 1 */
+#define SCTL_SCCLKSTAT2		0x54	/* Peripheral clocks status 2 */
+#define SCTL_SCRSTSTA		0x58	/* Reset status register */
+
+#define SCTL_SCRESCTRL1_USB_PHY_POR	(1 << 0)
+#define SCTL_SCRESCTRL1_USB_OTG	(1 << 1)
+#define SCTL_SCRESCTRL1_USB_HRST	(1 << 2)
+#define SCTL_SCRESCTRL1_USB_PHY_HOST	(1 << 3)
+#define SCTL_SCRESCTRL1_SATAII	(1 << 4)
+#define SCTL_SCRESCTRL1_VIP		(1 << 5)
+#define SCTL_SCRESCTRL1_PER_MMC0	(1 << 6)
+#define SCTL_SCRESCTRL1_PER_MMC1	(1 << 7)
+#define SCTL_SCRESCTRL1_PER_GPIO0	(1 << 8)
+#define SCTL_SCRESCTRL1_PER_GPIO1	(1 << 9)
+#define SCTL_SCRESCTRL1_PER_GPIO2	(1 << 10)
+#define SCTL_SCRESCTRL1_PER_GPIO3	(1 << 11)
+#define SCTL_SCRESCTRL1_PER_MTU0	(1 << 12)
+#define SCTL_SCRESCTRL1_KER_SPI0	(1 << 13)
+#define SCTL_SCRESCTRL1_KER_SPI1	(1 << 14)
+#define SCTL_SCRESCTRL1_KER_SPI2	(1 << 15)
+#define SCTL_SCRESCTRL1_KER_MCI0	(1 << 16)
+#define SCTL_SCRESCTRL1_KER_MCI1	(1 << 17)
+#define SCTL_SCRESCTRL1_PRE_HSI2C0	(1 << 18)
+#define SCTL_SCRESCTRL1_PER_HSI2C1	(1 << 19)
+#define SCTL_SCRESCTRL1_PER_HSI2C2	(1 << 20)
+#define SCTL_SCRESCTRL1_PER_HSI2C3	(1 << 21)
+#define SCTL_SCRESCTRL1_PER_MSP0	(1 << 22)
+#define SCTL_SCRESCTRL1_PER_MSP1	(1 << 23)
+#define SCTL_SCRESCTRL1_PER_MSP2	(1 << 24)
+#define SCTL_SCRESCTRL1_PER_MSP3	(1 << 25)
+#define SCTL_SCRESCTRL1_PER_MSP4	(1 << 26)
+#define SCTL_SCRESCTRL1_PER_MSP5	(1 << 27)
+#define SCTL_SCRESCTRL1_PER_MMC	(1 << 28)
+#define SCTL_SCRESCTRL1_KER_MSP0	(1 << 29)
+#define SCTL_SCRESCTRL1_KER_MSP1	(1 << 30)
+#define SCTL_SCRESCTRL1_KER_MSP2	(1 << 31)
+
+#define SCTL_SCPEREN0_UART0		(1 << 0)
+#define SCTL_SCPEREN0_UART1		(1 << 1)
+#define SCTL_SCPEREN0_UART2		(1 << 2)
+#define SCTL_SCPEREN0_UART3		(1 << 3)
+#define SCTL_SCPEREN0_MSP0		(1 << 4)
+#define SCTL_SCPEREN0_MSP1		(1 << 5)
+#define SCTL_SCPEREN0_MSP2		(1 << 6)
+#define SCTL_SCPEREN0_MSP3		(1 << 7)
+#define SCTL_SCPEREN0_MSP4		(1 << 8)
+#define SCTL_SCPEREN0_MSP5		(1 << 9)
+#define SCTL_SCPEREN0_SPI0		(1 << 10)
+#define SCTL_SCPEREN0_SPI1		(1 << 11)
+#define SCTL_SCPEREN0_SPI2		(1 << 12)
+#define SCTL_SCPEREN0_I2C0		(1 << 13)
+#define SCTL_SCPEREN0_I2C1		(1 << 14)
+#define SCTL_SCPEREN0_I2C2		(1 << 15)
+#define SCTL_SCPEREN0_I2C3		(1 << 16)
+#define SCTL_SCPEREN0_SVDO_LVDS		(1 << 17)
+#define SCTL_SCPEREN0_USB_HOST		(1 << 18)
+#define SCTL_SCPEREN0_USB_OTG		(1 << 19)
+#define SCTL_SCPEREN0_MCI0		(1 << 20)
+#define SCTL_SCPEREN0_MCI1		(1 << 21)
+#define SCTL_SCPEREN0_MCI2		(1 << 22)
+#define SCTL_SCPEREN0_MCI3		(1 << 23)
+#define SCTL_SCPEREN0_SATA		(1 << 24)
+#define SCTL_SCPEREN0_ETHERNET		(1 << 25)
+#define SCTL_SCPEREN0_VIC		(1 << 26)
+#define SCTL_SCPEREN0_DMA_AUDIO		(1 << 27)
+#define SCTL_SCPEREN0_DMA_SOC		(1 << 28)
+#define SCTL_SCPEREN0_RAM		(1 << 29)
+#define SCTL_SCPEREN0_VIP		(1 << 30)
+#define SCTL_SCPEREN0_ARM		(1 << 31)
+
+#define SCTL_SCPEREN1_UART0		(1 << 0)
+#define SCTL_SCPEREN1_UART1		(1 << 1)
+#define SCTL_SCPEREN1_UART2		(1 << 2)
+#define SCTL_SCPEREN1_UART3		(1 << 3)
+#define SCTL_SCPEREN1_MSP0		(1 << 4)
+#define SCTL_SCPEREN1_MSP1		(1 << 5)
+#define SCTL_SCPEREN1_MSP2		(1 << 6)
+#define SCTL_SCPEREN1_MSP3		(1 << 7)
+#define SCTL_SCPEREN1_MSP4		(1 << 8)
+#define SCTL_SCPEREN1_MSP5		(1 << 9)
+#define SCTL_SCPEREN1_SPI0		(1 << 10)
+#define SCTL_SCPEREN1_SPI1		(1 << 11)
+#define SCTL_SCPEREN1_SPI2		(1 << 12)
+#define SCTL_SCPEREN1_I2C0		(1 << 13)
+#define SCTL_SCPEREN1_I2C1		(1 << 14)
+#define SCTL_SCPEREN1_I2C2		(1 << 15)
+#define SCTL_SCPEREN1_I2C3		(1 << 16)
+#define SCTL_SCPEREN1_USB_PHY		(1 << 17)
+
+#endif /* __STA2X11_MFD_H */
-- 
1.7.7.2

[PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Alessandro Rubini]

This introduces 128 gpio bits (for each PCI device installed) with
working interrupt support.

Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
---
 drivers/gpio/Kconfig        |    8 +
 drivers/gpio/Makefile       |    1 +
 drivers/gpio/gpio-sta2x11.c |  435 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 444 insertions(+), 0 deletions(-)
 create mode 100644 drivers/gpio/gpio-sta2x11.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 7875c3f..d2dbd1d 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -153,6 +153,14 @@ config GPIO_PXA
 	help
 	  Say yes here to support the PXA GPIO device
 
+config GPIO_STA2X11
+	bool "STA2x11/ConneXt GPIO support"
+	depends on MFD_STA2X11
+	select GENERIC_IRQ_CHIP
+	help
+	  Say yes here to support the STA2x11/ConneXt GPIO device.
+	  The GPIO module has 128 GPIO pins with alternate functions.
+
 config GPIO_XILINX
 	bool "Xilinx GPIO support"
 	depends on PPC_OF || MICROBLAZE
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 1c2f6c0..fb749b1 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -49,6 +49,7 @@ obj-$(CONFIG_PLAT_SAMSUNG)	+= gpio-samsung.o
 obj-$(CONFIG_ARCH_SA1100)	+= gpio-sa1100.o
 obj-$(CONFIG_GPIO_SCH)		+= gpio-sch.o
 obj-$(CONFIG_GPIO_SODAVILLE)	+= gpio-sodaville.o
+obj-$(CONFIG_GPIO_STA2X11)	+= gpio-sta2x11.o
 obj-$(CONFIG_GPIO_STMPE)	+= gpio-stmpe.o
 obj-$(CONFIG_GPIO_SX150X)	+= gpio-sx150x.o
 obj-$(CONFIG_GPIO_TC3589X)	+= gpio-tc3589x.o
diff --git a/drivers/gpio/gpio-sta2x11.c b/drivers/gpio/gpio-sta2x11.c
new file mode 100644
index 0000000..38416be
--- /dev/null
+++ b/drivers/gpio/gpio-sta2x11.c
@@ -0,0 +1,435 @@
+/*
+ * STMicroelectronics ConneXt (STA2X11) GPIO driver
+ *
+ * Copyright 2012 ST Microelectronics (Alessandro Rubini)
+ * Based on gpio-ml-ioh.c, Copyright 2010 OKI Semiconductors Ltd.
+ * Also based on previous sta2x11 work, Copyright 2011 Wind River Systems, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ * See the GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/sta2x11-mfd.h>
+
+struct gsta_regs {
+	u32 dat;		/* 0x00 */
+	u32 dats;
+	u32 datc;
+	u32 pdis;
+	u32 dir;		/* 0x10 */
+	u32 dirs;
+	u32 dirc;
+	u32 unused_1c;
+	u32 afsela;		/* 0x20 */
+	u32 unused_24[7];
+	u32 rimsc;		/* 0x40 */
+	u32 fimsc;
+	u32 is;
+	u32 ic;
+};
+
+struct gsta_gpio {
+	spinlock_t			lock;
+	struct device			*dev;
+	void __iomem			*reg_base;
+	struct gsta_regs __iomem	*regs[GSTA_NR_BLOCKS];
+	struct gpio_chip		gpio;
+	int				irq_base;
+	/* FIXME: save the whole config here (AF, ...) */
+	unsigned			irq_type[GSTA_NR_GPIO];
+};
+
+static inline struct gsta_regs __iomem *__regs(struct gsta_gpio *chip, int nr)
+{
+	return chip->regs[nr / GSTA_GPIO_PER_BLOCK];
+}
+
+static inline u32 __bit(int nr)
+{
+	return 1U << (nr % GSTA_GPIO_PER_BLOCK);
+}
+
+/*
+ * gpio methods
+ */
+
+static void gsta_gpio_set(struct gpio_chip *gpio, unsigned nr, int val)
+{
+	struct gsta_gpio *chip = container_of(gpio, struct gsta_gpio, gpio);
+	struct gsta_regs __iomem *regs = __regs(chip, nr);
+	u32 bit = __bit(nr);
+
+	if (val)
+		writel(bit, &regs->dats);
+	else
+		writel(bit, &regs->datc);
+}
+
+static int gsta_gpio_get(struct gpio_chip *gpio, unsigned nr)
+{
+	struct gsta_gpio *chip = container_of(gpio, struct gsta_gpio, gpio);
+	struct gsta_regs __iomem *regs = __regs(chip, nr);
+	u32 bit = __bit(nr);
+
+	return readl(&regs->dat) & bit;
+}
+
+static int gsta_gpio_direction_output(struct gpio_chip *gpio, unsigned nr,
+				      int val)
+{
+	struct gsta_gpio *chip = container_of(gpio, struct gsta_gpio, gpio);
+	struct gsta_regs __iomem *regs = __regs(chip, nr);
+	u32 bit = __bit(nr);
+
+	writel(bit, &regs->dirs);
+	/* Data register after direction, otherwise pullup/down is selected */
+	if (val)
+		writel(bit, &regs->dats);
+	else
+		writel(bit, &regs->datc);
+	return 0;
+}
+
+static int gsta_gpio_direction_input(struct gpio_chip *gpio, unsigned nr)
+{
+	struct gsta_gpio *chip = container_of(gpio, struct gsta_gpio, gpio);
+	struct gsta_regs __iomem *regs = __regs(chip, nr);
+	u32 bit = __bit(nr);
+
+	writel(bit, &regs->dirc);
+	return 0;
+}
+
+static int gsta_gpio_to_irq(struct gpio_chip *gpio, unsigned offset)
+{
+	struct gsta_gpio *chip = container_of(gpio, struct gsta_gpio, gpio);
+	return chip->irq_base + offset;
+}
+
+static void gsta_gpio_setup(struct gsta_gpio *chip) /* called from probe */
+{
+	struct gpio_chip *gpio = &chip->gpio;
+
+	/*
+	 * ARCH_NR_GPIOS is currently 256 and dynamic allocation starts
+	 * from the end. However, for compatibility, we need the first
+	 * ConneXt device to start from gpio 0: it's the main chipset
+	 * on most boards so documents and drivers assume gpio0..gpio127
+	 */
+	static int gpio_base;
+
+	gpio->label = dev_name(chip->dev);
+	gpio->owner = THIS_MODULE;
+	gpio->direction_input = gsta_gpio_direction_input;
+	gpio->get = gsta_gpio_get;
+	gpio->direction_output = gsta_gpio_direction_output;
+	gpio->set = gsta_gpio_set;
+	gpio->dbg_show = NULL;
+	gpio->base = gpio_base;
+	gpio->ngpio = GSTA_NR_GPIO;
+	gpio->can_sleep = 0;
+	gpio->to_irq = gsta_gpio_to_irq;
+
+	/*
+	 * After the first device, turn to dynamic gpio numbers.
+	 * For example, with ARCH_NR_GPIOS = 256 we can fit two cards
+	 */
+	if (!gpio_base)
+		gpio_base = -1;
+}
+
+/*
+ * Special method: alternate functions and pullup/pulldown. This is only
+ * invoked on startup to configure gpio's according to platform data.
+ * FIXME : this functionality shall be managed (and exported to other drivers)
+ * via the pin control subsystem.
+ */
+static void gsta_set_config(struct gsta_gpio *chip, int nr, unsigned cfg)
+{
+	struct gsta_regs __iomem *regs = __regs(chip, nr);
+	unsigned long flags;
+	u32 bit = __bit(nr);
+	u32 val;
+	int err = 0;
+
+	pr_info("%s: %p %i %i\n", __func__, chip, nr, cfg);
+
+	if (cfg == PINMUX_TYPE_NONE)
+		return;
+
+	/* Alternate function or not? */
+	spin_lock_irqsave(&chip->lock, flags);
+	val = readl(&regs->afsela);
+	if (cfg == PINMUX_TYPE_FUNCTION)
+		val |= bit;
+	else
+		val &= ~bit;
+	writel(val | bit, &regs->afsela);
+	if (cfg == PINMUX_TYPE_FUNCTION) {
+		spin_unlock_irqrestore(&chip->lock, flags);
+		return;
+	}
+
+	/* not alternate function: set details */
+	switch (cfg) {
+	case PINMUX_TYPE_OUTPUT_LOW:
+		writel(bit, &regs->dirs);
+		writel(bit, &regs->datc);
+		break;
+	case PINMUX_TYPE_OUTPUT_HIGH:
+		writel(bit, &regs->dirs);
+		writel(bit, &regs->dats);
+		break;
+	case PINMUX_TYPE_INPUT:
+		writel(bit, &regs->dirc);
+		val = readl(&regs->pdis) | bit;
+		writel(val, &regs->pdis);
+		break;
+	case PINMUX_TYPE_INPUT_PULLUP:
+		writel(bit, &regs->dirc);
+		val = readl(&regs->pdis) & ~bit;
+		writel(val, &regs->pdis);
+		writel(bit, &regs->dats);
+		break;
+	case PINMUX_TYPE_INPUT_PULLDOWN:
+		writel(bit, &regs->dirc);
+		val = readl(&regs->pdis) & ~bit;
+		writel(val, &regs->pdis);
+		writel(bit, &regs->datc);
+		break;
+	default:
+		err = 1;
+	}
+	spin_unlock_irqrestore(&chip->lock, flags);
+	if (err)
+		pr_err("%s: chip %p, pin %i, cfg %i is invalid\n",
+		       __func__, chip, nr, cfg);
+}
+
+/*
+ * Irq methods
+ */
+
+static void gsta_irq_disable(struct irq_data *data)
+{
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(data);
+	struct gsta_gpio *chip = gc->private;
+	int nr = data->irq - chip->irq_base;
+	struct gsta_regs __iomem *regs = __regs(chip, nr);
+	u32 bit = __bit(nr);
+	u32 val;
+	unsigned long flags;
+
+	spin_lock_irqsave(&chip->lock, flags);
+	if (chip->irq_type[nr] & IRQ_TYPE_EDGE_RISING) {
+		val = readl(&regs->rimsc) & ~bit;
+		writel(val, &regs->rimsc);
+	}
+	if (chip->irq_type[nr] & IRQ_TYPE_EDGE_FALLING) {
+		val = readl(&regs->fimsc) & ~bit;
+		writel(val, &regs->fimsc);
+	}
+	spin_unlock_irqrestore(&chip->lock, flags);
+	return;
+}
+
+static void gsta_irq_enable(struct irq_data *data)
+{
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(data);
+	struct gsta_gpio *chip = gc->private;
+	int nr = data->irq - chip->irq_base;
+	struct gsta_regs __iomem *regs = __regs(chip, nr);
+	u32 bit = __bit(nr);
+	u32 val;
+	int type;
+	unsigned long flags;
+
+	type = chip->irq_type[nr];
+
+	spin_lock_irqsave(&chip->lock, flags);
+	val = readl(&regs->rimsc);
+	if (type & IRQ_TYPE_EDGE_RISING)
+		writel(val | bit, &regs->rimsc);
+	else
+		writel(val & ~bit, &regs->rimsc);
+	val = readl(&regs->rimsc);
+	if (type & IRQ_TYPE_EDGE_FALLING)
+		writel(val | bit, &regs->fimsc);
+	else
+		writel(val & ~bit, &regs->fimsc);
+	spin_unlock_irqrestore(&chip->lock, flags);
+	return;
+}
+
+static int gsta_irq_type(struct irq_data *d, unsigned int type)
+{
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+	struct gsta_gpio *chip = gc->private;
+	int nr = d->irq - chip->irq_base;
+
+	/* We only support edge interrupts */
+	if (!(type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING))) {
+		pr_debug("%s: unsupported type 0x%x\n", __func__, type);
+		return -EINVAL;
+	}
+
+	chip->irq_type[nr] = type; /* used for enable/disable */
+
+	gsta_irq_enable(d);
+	return 0;
+}
+
+static irqreturn_t gsta_gpio_handler(int irq, void *dev_id)
+{
+	struct gsta_gpio *chip = dev_id;
+	struct gsta_regs __iomem *regs;
+	u32 is;
+	int i, nr, base;
+	irqreturn_t ret = IRQ_NONE;
+
+	for (i = 0; i < GSTA_NR_BLOCKS; i++) {
+		regs = chip->regs[i];
+		base = chip->irq_base + i * GSTA_GPIO_PER_BLOCK;
+		while ((is = readl(&regs->is))) {
+			nr = __ffs(is);
+			irq = base + nr;
+			generic_handle_irq(irq);
+			writel(1 << nr, &regs->ic);
+			ret = IRQ_HANDLED;
+		}
+	}
+	return ret;
+}
+
+static __devinit void gsta_alloc_irq_chip(struct gsta_gpio *chip)
+{
+	struct irq_chip_generic *gc;
+	struct irq_chip_type *ct;
+
+	gc = irq_alloc_generic_chip(KBUILD_MODNAME, 1, chip->irq_base,
+				     chip->reg_base, handle_simple_irq);
+	gc->private = chip;
+	ct = gc->chip_types;
+
+	ct->chip.irq_set_type = gsta_irq_type;
+	ct->chip.irq_disable = gsta_irq_disable;
+	ct->chip.irq_enable = gsta_irq_enable;
+
+	/* FIXME: this makes at most 32 interrupts. Request 0 by now */
+	irq_setup_generic_chip(gc, 0 /* IRQ_MSK(GSTA_GPIO_PER_BLOCK) */, 0,
+			       IRQ_NOREQUEST | IRQ_NOPROBE, 0);
+
+	/* Set up all all 128 interrupts: code from setup_generic_chip */
+	{
+		struct irq_chip_type *ct = gc->chip_types;
+		int i, j;
+		for (j = 0; j < GSTA_NR_GPIO; j++) {
+			i = chip->irq_base + j;
+			irq_set_chip_and_handler(i, &ct->chip, ct->handler);
+			irq_set_chip_data(i, gc);
+			irq_modify_status(i, IRQ_NOREQUEST | IRQ_NOPROBE, 0);
+		}
+		gc->irq_cnt = i - gc->irq_base;
+	}
+}
+
+/* The platform device used here is instantiated by the MFD device */
+static int __devinit gsta_probe(struct platform_device *dev)
+{
+	int i, err;
+	struct pci_dev *pdev;
+	struct sta2x11_gpio_pdata *gpio_pdata;
+	struct gsta_gpio *chip;
+	struct resource *res;
+
+	pdev = *(struct pci_dev **)(dev->dev.platform_data);
+	gpio_pdata = dev_get_platdata(&pdev->dev);
+
+	if (gpio_pdata == NULL)
+		dev_err(&dev->dev, "no gpio config\n");
+	pr_debug("gpio config: %p\n", gpio_pdata);
+
+	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+
+	chip = devm_kzalloc(&dev->dev, sizeof(*chip), GFP_KERNEL);
+	chip->dev = &dev->dev;
+	chip->reg_base = devm_request_and_ioremap(&dev->dev, res);
+
+	for (i = 0; i < GSTA_NR_BLOCKS; i++) {
+		chip->regs[i] = chip->reg_base + i * 4096;
+		/* disable all irqs */
+		writel(0, &chip->regs[i]->rimsc);
+		writel(0, &chip->regs[i]->fimsc);
+		writel(~0, &chip->regs[i]->ic);
+	}
+	spin_lock_init(&chip->lock);
+	gsta_gpio_setup(chip);
+	for (i = 0; i < GSTA_NR_GPIO; i++)
+		gsta_set_config(chip, i, gpio_pdata->pinconfig[i]);
+
+	/* 384 was used in previous code: be compatible for other drivers */
+	err = irq_alloc_descs(-1, 384, GSTA_NR_GPIO, NUMA_NO_NODE);
+	if (err < 0) {
+		dev_warn(&dev->dev, "sta2x11 gpio: Can't get irq base (%i)\n",
+			 -err);
+		return err;
+	}
+	chip->irq_base = err;
+	gsta_alloc_irq_chip(chip);
+
+	err = request_irq(pdev->irq, gsta_gpio_handler,
+			     IRQF_SHARED, KBUILD_MODNAME, chip);
+	if (err < 0) {
+		dev_err(&dev->dev, "sta2x11 gpio: Can't request irq (%i)\n",
+			-err);
+		goto err_free_descs;
+	}
+
+	err = gpiochip_add(&chip->gpio);
+	if (err < 0) {
+		dev_err(&dev->dev, "sta2x11 gpio: Can't register (%i)\n",
+			-err);
+		goto err_free_irq;
+	}
+
+	platform_set_drvdata(dev, chip);
+	return 0;
+
+err_free_irq:
+	free_irq(pdev->irq, chip);
+err_free_descs:
+	irq_free_descs(chip->irq_base, GSTA_NR_GPIO);
+	return err;
+}
+
+static struct platform_driver sta2x11_gpio_platform_driver = {
+	.driver = {
+		.name	= "sta2x11-gpio",
+		.owner	= THIS_MODULE,
+	},
+	.probe = gsta_probe,
+};
+
+module_platform_driver(sta2x11_gpio_platform_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("sta2x11_gpio GPIO driver");
-- 
1.7.7.2

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Linus Walleij]

On Thu, Apr 12, 2012 at 10:48 AM, Alessandro Rubini <rubini@gnudd.com> wrote:

> +/*
> + * Special method: alternate functions and pullup/pulldown. This is only
> + * invoked on startup to configure gpio's according to platform data.
> + * FIXME : this functionality shall be managed (and exported to other drivers)
> + * via the pin control subsystem.
> + */
> +static void gsta_set_config(struct gsta_gpio *chip, int nr, unsigned cfg)
> +{
> +       struct gsta_regs __iomem *regs = __regs(chip, nr);
> +       unsigned long flags;
> +       u32 bit = __bit(nr);
> +       u32 val;
> +       int err = 0;
> +
> +       pr_info("%s: %p %i %i\n", __func__, chip, nr, cfg);
> +
> +       if (cfg == PINMUX_TYPE_NONE)
> +               return;
> +
> +       /* Alternate function or not? */
> +       spin_lock_irqsave(&chip->lock, flags);
> +       val = readl(&regs->afsela);
> +       if (cfg == PINMUX_TYPE_FUNCTION)
> +               val |= bit;
> +       else
> +               val &= ~bit;
> +       writel(val | bit, &regs->afsela);
> +       if (cfg == PINMUX_TYPE_FUNCTION) {
> +               spin_unlock_irqrestore(&chip->lock, flags);
> +               return;
> +       }
> +
> +       /* not alternate function: set details */
> +       switch (cfg) {
> +       case PINMUX_TYPE_OUTPUT_LOW:
> +               writel(bit, &regs->dirs);
> +               writel(bit, &regs->datc);
> +               break;
> +       case PINMUX_TYPE_OUTPUT_HIGH:
> +               writel(bit, &regs->dirs);
> +               writel(bit, &regs->dats);
> +               break;
> +       case PINMUX_TYPE_INPUT:
> +               writel(bit, &regs->dirc);
> +               val = readl(&regs->pdis) | bit;
> +               writel(val, &regs->pdis);
> +               break;
> +       case PINMUX_TYPE_INPUT_PULLUP:
> +               writel(bit, &regs->dirc);
> +               val = readl(&regs->pdis) & ~bit;
> +               writel(val, &regs->pdis);
> +               writel(bit, &regs->dats);
> +               break;
> +       case PINMUX_TYPE_INPUT_PULLDOWN:
> +               writel(bit, &regs->dirc);
> +               val = readl(&regs->pdis) & ~bit;
> +               writel(val, &regs->pdis);
> +               writel(bit, &regs->datc);
> +               break;
> +       default:
> +               err = 1;
> +       }
> +       spin_unlock_irqrestore(&chip->lock, flags);
> +       if (err)
> +               pr_err("%s: chip %p, pin %i, cfg %i is invalid\n",
> +                      __func__, chip, nr, cfg);
> +}

I would still prefer to use the pinctrl subsystem for this from day 1 instead of
adding more custom stuff for later refactoring...

Yours,
Linus Walleij

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Alessandro Rubini]

> I would still prefer to use the pinctrl subsystem for this from day
> 1 instead of adding more custom stuff for later refactoring...

I see your point. I attacked pinctrl some time ago, but it is overly
complex for this simple stuff. We have static configuration that is
enacted at boot, and that's it.  Using pinctrl would mean much more
code (and more bugs, as a side effect) for no real advantage.  I
appreciate the flexibility of pinctrl, and I see it's really good to
have a way to describe complex SoC hardware, but it just isn't always
needed.

Besides, it's still marked as experimental, which on one side is not
reassuring about its stability, and on the other means my whole
chipset should depend on experimental as a consequence.

thanks
/alessandro

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Linus Walleij]

On Fri, Apr 13, 2012 at 1:44 PM, Alessandro Rubini <rubini@gnudd.com> wrote:

> Besides, it's still marked as experimental, which on one side is not
> reassuring about its stability, and on the other means my whole
> chipset should depend on experimental as a consequence.

Yeah I heard that having it marked experimental was considered
harmful for adoption so we have pushed a patch removing the
experimental status. It should appear in -next tomorrow or so...

Yours,
Linus Walleij

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Linus Walleij]

On Thu, Apr 12, 2012 at 10:48 AM, Alessandro Rubini <rubini@gnudd.com> wrote:

> This introduces 128 gpio bits (for each PCI device installed) with
> working interrupt support.
>
> Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
> Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
> Cc: Alan Cox <alan@linux.intel.com>

Grant, I prefer that you make a decision on this driver since I have
a conflict of interest (it's written for ST).

Yours,
Linus Walleij

Re: [PATCH V3 0/2] MFD and GPIO for STA2X11

[Samuel Ortiz]

Hi Alessandro,

On Thu, Apr 12, 2012 at 10:48:32AM +0200, Alessandro Rubini wrote:
> These two patches introduce the multi-function device and GPIO support for
> the STA2X11 I/O Hub.  Core PCI support is already in linux-next.
> 
> V1: sent on Jan 26th as RFC and got no comments back
> 
> V2: sent on Feb 16th, fixed a number of minor details, got comments from
> Linus Walleij and Samuel Ortiz.
> 
> V3: accepted all suggestions.  I delayed this resending a while because
> I hoped the base STA2X11 patches to be accepted, but despite the positive
> comments I got on those patches, they are not in linux-next as of today
There was a misunderstanding here: I was expecting a new patchset from you
before applying it, since v2 had some unresolved comments.
In fact, there are still some minor issues with it, see my comments on the MFD
patch.

Cheers,
Samuel.

-- 
Intel Open Source Technology Centre
http://oss.intel.com/

Re: [PATCH V3 1/2] mfd: Add driver for STA2X11 MFD block

[Samuel Ortiz]

Hi Alessandro,

On Thu, Apr 12, 2012 at 10:48:44AM +0200, Alessandro Rubini wrote:
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 29f463c..c194c67 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -873,6 +873,12 @@ config MFD_RC5T583
>  	  Additional drivers must be enabled in order to use the
>  	  different functionality of the device.
>  
> +config MFD_STA2X11
> +	bool "STA2X11 multi function device support"
> +	depends on STA2X11
> +	select MFD_CORE
> +	select GPIO_STA2X11
So you haven't fixed that one:

- You should not select GPIO_STA2X11 as this won't select the STA2X211 gpio
  driver dependencies for you. So if you build this driver with GPIOLIB=n then
  your build will fail.
- Why would this one depend on STA2X11 ? I see that you're calling
  sta2x11_get_instance() from this driver but I wonder if you could simply
  replace the mfd->instance pointer with one pointing to the pci_dev. Not
  depending on STA2X11 at all gives you the benefit of a much larger build
  coverage from linux-next for example.


> +/* Bar 0 */
> +enum bar0_cells {
> +	GPIO_0 = 0,
> +	GPIO_1,
> +	GPIO_2,
> +	GPIO_3,
> +	SCTL,
> +	SCR,
> +	TIME,
> +};
Please protect those ones with a proper namespace.

Cheers,
Samuel.

-- 
Intel Open Source Technology Centre
http://oss.intel.com/

Re: [PATCH V3 1/2] mfd: Add driver for STA2X11 MFD block

[Alessandro Rubini]

Hello Samuel, thanks for commenting.

> - You should not select GPIO_STA2X11 as this won't select the STA2X211 gpio
>   driver dependencies for you. So if you build this driver with GPIOLIB=n then
>   your build will fail.

Ok. I recall this now, but I've forgotten while editing.

> - Why would this one depend on STA2X11 ? I see that you're calling
>   sta2x11_get_instance() from this driver but I wonder if you could simply
>   replace the mfd->instance pointer with one pointing to the pci_dev. Not
>   depending on STA2X11 at all gives you the benefit of a much larger build
>   coverage from linux-next for example.

Right. But I need to know the instance, because other drivers will
call on mfd for some configuration, and I need to match their device
instance with the mfd one.  The sta2x11 is a complex bridge, with 4
sub-buses, but being pci you can in theory plug two such boards
in the same computer, and I'd love that setup to work properly.

>> +/* Bar 0 */
>> +enum bar0_cells {
>> +	GPIO_0 = 0,
>> +	GPIO_1,
>> +	GPIO_2,
>> +	GPIO_3,
>> +	SCTL,
>> +	SCR,
>> +	TIME,
>> +};
> Please protect those ones with a proper namespace.

I remember this and I didn't do it on purpose (but I didn't comment on
the submission because so much time had passed). I protected all the
gpio bits, but this is only a local shortcut (it's in the .c
file), to name the ordering of the hardware blocks in the mfd.
It's only used a few lines later to build resource addresses.

Thanks
/alessandro

Re: [PATCH V3 1/2] mfd: Add driver for STA2X11 MFD block

[Samuel Ortiz]

Hi Alessandro,

On Thu, Apr 12, 2012 at 10:48:44AM +0200, Alessandro Rubini wrote:
> This also introduces <asm/sta2x11.h> to export a function that is in
> the base sta2x11 support patches. The header will increase with other
> prototypes and constants over time.
I applied this one, after removing the GPIO_STA2X11 selection from the Kconfig
entry, and after protecting bar0_cells and bar1_cells namespace with a STA2X11
prefix.
Please have a look at it and let me know if there are some issues with it.

Cheers,
Samuel.

-- 
Intel Open Source Technology Centre
http://oss.intel.com/

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Samuel Ortiz]

Hi Alessandro,

On Thu, Apr 12, 2012 at 10:48:55AM +0200, Alessandro Rubini wrote:
> This introduces 128 gpio bits (for each PCI device installed) with
> working interrupt support.
I also applied this one, although I'd prefer to get Grant's ACK on it.
Grant could also apply it to his tree as the build time dependencies are
protected by the MFD_STA2X11 symbol.

Cheers,
Samuel.

-- 
Intel Open Source Technology Centre
http://oss.intel.com/

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Grant Likely]

On Thu, 12 Apr 2012 10:48:55 +0200, Alessandro Rubini <rubini@gnudd.com> wrote:
> This introduces 128 gpio bits (for each PCI device installed) with
> working interrupt support.
> 
> Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
> Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
> Cc: Alan Cox <alan@linux.intel.com>
> ---
[...]
> +/* The platform device used here is instantiated by the MFD device */
> +static int __devinit gsta_probe(struct platform_device *dev)
> +{
> +	int i, err;
> +	struct pci_dev *pdev;
> +	struct sta2x11_gpio_pdata *gpio_pdata;
> +	struct gsta_gpio *chip;
> +	struct resource *res;
> +
> +	pdev = *(struct pci_dev **)(dev->dev.platform_data);
> +	gpio_pdata = dev_get_platdata(&pdev->dev);
> +
> +	if (gpio_pdata == NULL)
> +		dev_err(&dev->dev, "no gpio config\n");
> +	pr_debug("gpio config: %p\n", gpio_pdata);
> +
> +	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
> +
> +	chip = devm_kzalloc(&dev->dev, sizeof(*chip), GFP_KERNEL);
> +	chip->dev = &dev->dev;
> +	chip->reg_base = devm_request_and_ioremap(&dev->dev, res);
> +
> +	for (i = 0; i < GSTA_NR_BLOCKS; i++) {
> +		chip->regs[i] = chip->reg_base + i * 4096;
> +		/* disable all irqs */
> +		writel(0, &chip->regs[i]->rimsc);
> +		writel(0, &chip->regs[i]->fimsc);
> +		writel(~0, &chip->regs[i]->ic);
> +	}
> +	spin_lock_init(&chip->lock);
> +	gsta_gpio_setup(chip);
> +	for (i = 0; i < GSTA_NR_GPIO; i++)
> +		gsta_set_config(chip, i, gpio_pdata->pinconfig[i]);
> +
> +	/* 384 was used in previous code: be compatible for other drivers */
> +	err = irq_alloc_descs(-1, 384, GSTA_NR_GPIO, NUMA_NO_NODE);
> +	if (err < 0) {
> +		dev_warn(&dev->dev, "sta2x11 gpio: Can't get irq base (%i)\n",
> +			 -err);
> +		return err;
> +	}
> +	chip->irq_base = err;

Where does the number 384 come from?  It looks like the driver only
needs to allocate a range of irqs and that it doesn't actually matter
what the real numbers are.  Can 0 be used instead?

Actually, I'd rather see this driver switched to using
irq_domain_add_linear so that irq_descs can be allocated on demand
instead of all at once.  That way only gpios actually used for irqs
get setup.

To convert, use irq_domain_add_linear() and then irq_data->hwirq gets
populated with the gpio number automatically for you and
irq_find_mapping takes care of the hwirq->irq reverse lookup.

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Alessandro Rubini]

Hello Grant. Sorry for the delay.

>> +	/* 384 was used in previous code: be compatible for other drivers */
>> +	err = irq_alloc_descs(-1, 384, GSTA_NR_GPIO, NUMA_NO_NODE);

> Where does the number 384 come from?  It looks like the driver only
> needs to allocate a range of irqs and that it doesn't actually matter
> what the real numbers are.  Can 0 be used instead?

The problem is that there are a number of drivers already working (but
not ready to be upstreamed), and we'd better continue using them.  So,
the mmc driver is requesting a specific interrupt number.  The code is
GPL (published on sourceforge) and I'd better remain compatible.

I'm not completely clear (yet) about how to get the right interrupt
number in those other drivers, but I'm willing to remove the constraint
as they are cleaned up and submitted.

> Actually, I'd rather see this driver switched to using
> irq_domain_add_linear so that irq_descs can be allocated on demand
> instead of all at once.  That way only gpios actually used for irqs
> get setup.

If it is a request, I'll evaluate it soon.  I assume an incremental
patch over what Samuel has already picked up is fine.

thanks
/alessandro

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Mark Brown]

On Mon, May 14, 2012 at 09:25:34AM +0200, Alessandro Rubini wrote:

> >> +	/* 384 was used in previous code: be compatible for other drivers */
> >> +	err = irq_alloc_descs(-1, 384, GSTA_NR_GPIO, NUMA_NO_NODE);

> > Where does the number 384 come from?  It looks like the driver only
> > needs to allocate a range of irqs and that it doesn't actually matter
> > what the real numbers are.  Can 0 be used instead?

> The problem is that there are a number of drivers already working (but
> not ready to be upstreamed), and we'd better continue using them.  So,
> the mmc driver is requesting a specific interrupt number.  The code is
> GPL (published on sourceforge) and I'd better remain compatible.

> I'm not completely clear (yet) about how to get the right interrupt
> number in those other drivers, but I'm willing to remove the constraint
> as they are cleaned up and submitted.

Use platform data for both this driver and the other drivers (or device
tree if you're doing that).  This will hard code the magic numbers in
the board files, not in the driver.

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Alessandro Rubini]

Me:
>> I'm not completely clear (yet) about how to get the right interrupt
>> number in those other drivers, but I'm willing to remove the constraint
>> as they are cleaned up and submitted.

Mark Brown:
> Use platform data for both this driver and the other drivers (or device
> tree if you're doing that).  This will hard code the magic numbers in
> the board files, not in the driver.

Yes, but it's not that easy. If the gpio driver gets unpredictable
interrupt numbers associated to the pins, the other drivers must
recover those numbers in some way.  That's why I currently started
from 384, like the prevoous gpio driver was doing: the platform data
uses that knowledge in the drivers I'm still using internally (but are
not submittable as-is, so I'm working on them).

thanks
/alessandro

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 939 bytes --]

On Mon, May 14, 2012 at 11:51:11AM +0200, Alessandro Rubini wrote:
> Me:
> >> I'm not completely clear (yet) about how to get the right interrupt
> >> number in those other drivers, but I'm willing to remove the constraint
> >> as they are cleaned up and submitted.

> Mark Brown:
> > Use platform data for both this driver and the other drivers (or device
> > tree if you're doing that).  This will hard code the magic numbers in
> > the board files, not in the driver.

> Yes, but it's not that easy. If the gpio driver gets unpredictable
> interrupt numbers associated to the pins, the other drivers must
> recover those numbers in some way.  That's why I currently started
> from 384, like the prevoous gpio driver was doing: the platform data
> uses that knowledge in the drivers I'm still using internally (but are
> not submittable as-is, so I'm working on them).

If you use platform data why would you get unpredicatable numbers?

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Alessandro Rubini]

> If you use platform data why would you get unpredicatable numbers?

Because I request the irq numbers from the gpio driver (now I request
a free slot starting from 384, because previous drivers had it
hardwired).  So if the gpio driver requests a slot starting from 0 it
may get different values -- in general I can't now what it gets.

So the irq number is unknown at compile time, and can't be written in
the platform data.

Actually, the problem is there in any case if you plug two chips in
the same computer -- this is extremely unlikely because the sta2x11 is
currently only used as a motherboard chipset.  The thing must be
fixed in any case, because it's a pci device, but still using 384
allows me to use platform data for the current drivers that I'm running
until they are ported to upstream quality standards.

/alessandro

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 599 bytes --]

On Mon, May 14, 2012 at 12:06:45PM +0200, Alessandro Rubini wrote:

> > If you use platform data why would you get unpredicatable numbers?

> Because I request the irq numbers from the gpio driver (now I request
> a free slot starting from 384, because previous drivers had it
> hardwired).  So if the gpio driver requests a slot starting from 0 it
> may get different values -- in general I can't now what it gets.

But this is because you're not using platform data!  If you use platform
data to tell all the drivers including the gpio driver which ranges to
use then this problem does not exist.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH V3 2/2] gpio: add STA2X11 GPIO block

[Samuel Ortiz]

Hi Alessandro,

On Mon, May 14, 2012 at 09:25:34AM +0200, Alessandro Rubini wrote:
> Hello Grant. Sorry for the delay.
> 
> >> +	/* 384 was used in previous code: be compatible for other drivers */
> >> +	err = irq_alloc_descs(-1, 384, GSTA_NR_GPIO, NUMA_NO_NODE);
> 
> > Where does the number 384 come from?  It looks like the driver only
> > needs to allocate a range of irqs and that it doesn't actually matter
> > what the real numbers are.  Can 0 be used instead?
> 
> The problem is that there are a number of drivers already working (but
> not ready to be upstreamed), and we'd better continue using them.  So,
> the mmc driver is requesting a specific interrupt number.  The code is
> GPL (published on sourceforge) and I'd better remain compatible.
> 
> I'm not completely clear (yet) about how to get the right interrupt
> number in those other drivers, but I'm willing to remove the constraint
> as they are cleaned up and submitted.
> 
> > Actually, I'd rather see this driver switched to using
> > irq_domain_add_linear so that irq_descs can be allocated on demand
> > instead of all at once.  That way only gpios actually used for irqs
> > get setup.
> 
> If it is a request, I'll evaluate it soon.  I assume an incremental
> patch over what Samuel has already picked up is fine.
That is fine with me at least.

Cheers,
Samuel.

-- 
Intel Open Source Technology Centre
http://oss.intel.com/