* [PATCH v2 0/2] Add support for Thecus N2350 board @ 2023-04-12 2:57 ` Tony Dinh 0 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-12 2:57 UTC (permalink / raw) To: Andrew Lunn, Gregory Clement, devicetree, linux-arm-kernel Cc: Tony Dinh, Arnd Bergmann, Krzysztof Kozlowski, Olof Johansson, Rob Herring, Sebastian Hesselbarth, linux-kernel, soc Thecus N2350 is a NAS based on Marvell Armada 385 SoC. Board Specification: - Marvel MV88F6820 Dual Core at 1GHz - 1 GiB DDR4 RAM - 4MB Macronix mx25l3205d SPI flash - 512MB Hynix H27U4G8F2DTR-BC NAND flash - I2C - 2x USB 3.0 - 1x GBE LAN port (PHY: Marvell 88E1510) - 2x SATA (hot swap slots) - 3x buttons - 10x LEDS - serial console Changes in v2: - Add marvell,38x.yaml. For now, add this binding to the Marvell directory to keep it consistent with other Marvell yaml files. At a later date and a separate patch, consolidate the Marvell yaml files into marvell.yaml. - Fix various DT bindings conformance (too numerous to list) - Vendor prefix is not necessary, so remove it. Tony Dinh (2): ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x ARM: dts: mvebu: add Thecus N2350 board DTS .../bindings/arm/marvell/armada-38x.yaml | 27 ++ arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/armada-385-thecus-n2350.dts | 432 ++++++++++++++++++ 3 files changed, 460 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml create mode 100644 arch/arm/boot/dts/armada-385-thecus-n2350.dts -- 2.30.2 ^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v2 0/2] Add support for Thecus N2350 board @ 2023-04-12 2:57 ` Tony Dinh 0 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-12 2:57 UTC (permalink / raw) To: Andrew Lunn, Gregory Clement, devicetree, linux-arm-kernel Cc: Tony Dinh, Arnd Bergmann, Krzysztof Kozlowski, Olof Johansson, Rob Herring, Sebastian Hesselbarth, linux-kernel, soc Thecus N2350 is a NAS based on Marvell Armada 385 SoC. Board Specification: - Marvel MV88F6820 Dual Core at 1GHz - 1 GiB DDR4 RAM - 4MB Macronix mx25l3205d SPI flash - 512MB Hynix H27U4G8F2DTR-BC NAND flash - I2C - 2x USB 3.0 - 1x GBE LAN port (PHY: Marvell 88E1510) - 2x SATA (hot swap slots) - 3x buttons - 10x LEDS - serial console Changes in v2: - Add marvell,38x.yaml. For now, add this binding to the Marvell directory to keep it consistent with other Marvell yaml files. At a later date and a separate patch, consolidate the Marvell yaml files into marvell.yaml. - Fix various DT bindings conformance (too numerous to list) - Vendor prefix is not necessary, so remove it. Tony Dinh (2): ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x ARM: dts: mvebu: add Thecus N2350 board DTS .../bindings/arm/marvell/armada-38x.yaml | 27 ++ arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/armada-385-thecus-n2350.dts | 432 ++++++++++++++++++ 3 files changed, 460 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml create mode 100644 arch/arm/boot/dts/armada-385-thecus-n2350.dts -- 2.30.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x 2023-04-12 2:57 ` Tony Dinh @ 2023-04-12 2:57 ` Tony Dinh -1 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-12 2:57 UTC (permalink / raw) To: Andrew Lunn, Gregory Clement, devicetree, linux-arm-kernel Cc: Tony Dinh, Krzysztof Kozlowski, Rob Herring, Sebastian Hesselbarth, linux-kernel Add device tree binding for Marvell Armada 38x. Signed-off-by: Tony Dinh <mibodhi@gmail.com> --- Changes in v2: - Add marvell,38x.yaml. For now, add this binding to the Marvell directory to keep it consistent with other Marvell yaml files. At a later date and a separate patch, consolidate the Marvell yaml files into marvell.yaml. .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ 1 file changed, 27 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml b/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml new file mode 100644 index 000000000000..096bd46d932a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml @@ -0,0 +1,27 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/marvell/marvell,38x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell Armada 38x Platforms + +maintainers: + - Gregory CLEMENT <gregory.clement@bootlin.com> + - Andrew Lunn <andrew@lunn.ch> + +properties: + $nodename: + const: '/' + compatible: + oneOf: + + - description: Armada 380 SoC + items: + - const: marvell,armada380 + + - description: Armada 385 SoC + items: + - const: marvell,armada385 + +additionalProperties: true -- 2.30.2 ^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x @ 2023-04-12 2:57 ` Tony Dinh 0 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-12 2:57 UTC (permalink / raw) To: Andrew Lunn, Gregory Clement, devicetree, linux-arm-kernel Cc: Tony Dinh, Krzysztof Kozlowski, Rob Herring, Sebastian Hesselbarth, linux-kernel Add device tree binding for Marvell Armada 38x. Signed-off-by: Tony Dinh <mibodhi@gmail.com> --- Changes in v2: - Add marvell,38x.yaml. For now, add this binding to the Marvell directory to keep it consistent with other Marvell yaml files. At a later date and a separate patch, consolidate the Marvell yaml files into marvell.yaml. .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ 1 file changed, 27 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml b/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml new file mode 100644 index 000000000000..096bd46d932a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml @@ -0,0 +1,27 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/marvell/marvell,38x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell Armada 38x Platforms + +maintainers: + - Gregory CLEMENT <gregory.clement@bootlin.com> + - Andrew Lunn <andrew@lunn.ch> + +properties: + $nodename: + const: '/' + compatible: + oneOf: + + - description: Armada 380 SoC + items: + - const: marvell,armada380 + + - description: Armada 385 SoC + items: + - const: marvell,armada385 + +additionalProperties: true -- 2.30.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x 2023-04-12 2:57 ` Tony Dinh @ 2023-04-12 7:13 ` Krzysztof Kozlowski -1 siblings, 0 replies; 24+ messages in thread From: Krzysztof Kozlowski @ 2023-04-12 7:13 UTC (permalink / raw) To: Tony Dinh, Andrew Lunn, Gregory Clement, devicetree, linux-arm-kernel Cc: Krzysztof Kozlowski, Rob Herring, Sebastian Hesselbarth, linux-kernel On 12/04/2023 04:57, Tony Dinh wrote: > Add device tree binding for Marvell Armada 38x. > > Signed-off-by: Tony Dinh <mibodhi@gmail.com> Use subject prefixes matching the subsystem (which you can get for example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory your patch is touching). This is not DTS. These are bindings. > --- > > Changes in v2: > - Add marvell,38x.yaml. For now, add this binding to the Marvell > directory to keep it consistent with other Marvell yaml files. > At a later date and a separate patch, consolidate the Marvell > yaml files into marvell.yaml. > > .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ > 1 file changed, 27 insertions(+) > create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml marvell,armada-38x.yaml Or just squash it with existing armada bindings... Keeping one binding per one SoC group is a bit a lot. > > diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml b/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > new file mode 100644 > index 000000000000..096bd46d932a > --- /dev/null > +++ b/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > @@ -0,0 +1,27 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/arm/marvell/marvell,38x.yaml# Does not look like you tested the bindings. Please run `make dt_binding_check` (see Documentation/devicetree/bindings/writing-schema.rst for instructions). Best regards, Krzysztof ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x @ 2023-04-12 7:13 ` Krzysztof Kozlowski 0 siblings, 0 replies; 24+ messages in thread From: Krzysztof Kozlowski @ 2023-04-12 7:13 UTC (permalink / raw) To: Tony Dinh, Andrew Lunn, Gregory Clement, devicetree, linux-arm-kernel Cc: Krzysztof Kozlowski, Rob Herring, Sebastian Hesselbarth, linux-kernel On 12/04/2023 04:57, Tony Dinh wrote: > Add device tree binding for Marvell Armada 38x. > > Signed-off-by: Tony Dinh <mibodhi@gmail.com> Use subject prefixes matching the subsystem (which you can get for example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory your patch is touching). This is not DTS. These are bindings. > --- > > Changes in v2: > - Add marvell,38x.yaml. For now, add this binding to the Marvell > directory to keep it consistent with other Marvell yaml files. > At a later date and a separate patch, consolidate the Marvell > yaml files into marvell.yaml. > > .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ > 1 file changed, 27 insertions(+) > create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml marvell,armada-38x.yaml Or just squash it with existing armada bindings... Keeping one binding per one SoC group is a bit a lot. > > diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml b/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > new file mode 100644 > index 000000000000..096bd46d932a > --- /dev/null > +++ b/Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > @@ -0,0 +1,27 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/arm/marvell/marvell,38x.yaml# Does not look like you tested the bindings. Please run `make dt_binding_check` (see Documentation/devicetree/bindings/writing-schema.rst for instructions). Best regards, Krzysztof _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x 2023-04-12 2:57 ` Tony Dinh @ 2023-04-12 12:36 ` Rob Herring -1 siblings, 0 replies; 24+ messages in thread From: Rob Herring @ 2023-04-12 12:36 UTC (permalink / raw) To: Tony Dinh Cc: Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: > Add device tree binding for Marvell Armada 38x. > > Signed-off-by: Tony Dinh <mibodhi@gmail.com> > --- > > Changes in v2: > - Add marvell,38x.yaml. For now, add this binding to the Marvell > directory to keep it consistent with other Marvell yaml files. > At a later date and a separate patch, consolidate the Marvell > yaml files into marvell.yaml. > > .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ > 1 file changed, 27 insertions(+) > create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema. ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x @ 2023-04-12 12:36 ` Rob Herring 0 siblings, 0 replies; 24+ messages in thread From: Rob Herring @ 2023-04-12 12:36 UTC (permalink / raw) To: Tony Dinh Cc: Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: > Add device tree binding for Marvell Armada 38x. > > Signed-off-by: Tony Dinh <mibodhi@gmail.com> > --- > > Changes in v2: > - Add marvell,38x.yaml. For now, add this binding to the Marvell > directory to keep it consistent with other Marvell yaml files. > At a later date and a separate patch, consolidate the Marvell > yaml files into marvell.yaml. > > .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ > 1 file changed, 27 insertions(+) > create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema. _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x 2023-04-12 12:36 ` Rob Herring @ 2023-04-12 19:05 ` Tony Dinh -1 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-12 19:05 UTC (permalink / raw) To: Rob Herring Cc: Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth Hi Rob, Hi Krzysztof, On Wed, Apr 12, 2023 at 5:36 AM Rob Herring <robh@kernel.org> wrote: > > > On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: > > Add device tree binding for Marvell Armada 38x. > > > > Signed-off-by: Tony Dinh <mibodhi@gmail.com> > > --- > > > > Changes in v2: > > - Add marvell,38x.yaml. For now, add this binding to the Marvell > > directory to keep it consistent with other Marvell yaml files. > > At a later date and a separate patch, consolidate the Marvell > > yaml files into marvell.yaml. > > > > .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ > > 1 file changed, 27 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > > > > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > yamllint warnings/errors: > > dtschema/dtc warnings/errors: > ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename > expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# > > doc reference errors (make refcheckdocs): > > See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com > > The base for the series is generally the latest rc1. A different dependency > should be noted in *this* patch. > > If you already ran 'make dt_binding_check' and didn't see the above > error(s), then make sure 'yamllint' is installed and dt-schema is up to > date: > > pip3 install dtschema --upgrade > > Please check and re-submit after running the above command yourself. Note > that DT_SCHEMA_FILES can be set to your schema file to speed up checking > your schema. However, it must be unset to test all examples with your schema. > Thanks for the reviews. After running make dt_binding_check for it seems like hours (on a dual-core 1.8GHz ARM box), I got impatient and used make CHECK_DTBS=y armada-385-thecus-n2350.dtb I'll move this to another faster box and run make dt_binding_check. All the best, Tony ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x @ 2023-04-12 19:05 ` Tony Dinh 0 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-12 19:05 UTC (permalink / raw) To: Rob Herring Cc: Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth Hi Rob, Hi Krzysztof, On Wed, Apr 12, 2023 at 5:36 AM Rob Herring <robh@kernel.org> wrote: > > > On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: > > Add device tree binding for Marvell Armada 38x. > > > > Signed-off-by: Tony Dinh <mibodhi@gmail.com> > > --- > > > > Changes in v2: > > - Add marvell,38x.yaml. For now, add this binding to the Marvell > > directory to keep it consistent with other Marvell yaml files. > > At a later date and a separate patch, consolidate the Marvell > > yaml files into marvell.yaml. > > > > .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ > > 1 file changed, 27 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > > > > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > yamllint warnings/errors: > > dtschema/dtc warnings/errors: > ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename > expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# > > doc reference errors (make refcheckdocs): > > See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com > > The base for the series is generally the latest rc1. A different dependency > should be noted in *this* patch. > > If you already ran 'make dt_binding_check' and didn't see the above > error(s), then make sure 'yamllint' is installed and dt-schema is up to > date: > > pip3 install dtschema --upgrade > > Please check and re-submit after running the above command yourself. Note > that DT_SCHEMA_FILES can be set to your schema file to speed up checking > your schema. However, it must be unset to test all examples with your schema. > Thanks for the reviews. After running make dt_binding_check for it seems like hours (on a dual-core 1.8GHz ARM box), I got impatient and used make CHECK_DTBS=y armada-385-thecus-n2350.dtb I'll move this to another faster box and run make dt_binding_check. All the best, Tony _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x 2023-04-12 19:05 ` Tony Dinh @ 2023-04-13 7:51 ` Krzysztof Kozlowski -1 siblings, 0 replies; 24+ messages in thread From: Krzysztof Kozlowski @ 2023-04-13 7:51 UTC (permalink / raw) To: Tony Dinh, Rob Herring Cc: Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth On 12/04/2023 21:05, Tony Dinh wrote: > Hi Rob, > Hi Krzysztof, > > On Wed, Apr 12, 2023 at 5:36 AM Rob Herring <robh@kernel.org> wrote: >> >> >> On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: >>> Add device tree binding for Marvell Armada 38x. >>> >>> Signed-off-by: Tony Dinh <mibodhi@gmail.com> >>> --- >>> >>> Changes in v2: >>> - Add marvell,38x.yaml. For now, add this binding to the Marvell >>> directory to keep it consistent with other Marvell yaml files. >>> At a later date and a separate patch, consolidate the Marvell >>> yaml files into marvell.yaml. >>> >>> .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ >>> 1 file changed, 27 insertions(+) >>> create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml >>> >> >> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' >> on your patch (DT_CHECKER_FLAGS is new in v5.13): >> >> yamllint warnings/errors: >> >> dtschema/dtc warnings/errors: >> ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename >> expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# >> >> doc reference errors (make refcheckdocs): >> >> See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com >> >> The base for the series is generally the latest rc1. A different dependency >> should be noted in *this* patch. >> >> If you already ran 'make dt_binding_check' and didn't see the above >> error(s), then make sure 'yamllint' is installed and dt-schema is up to >> date: >> >> pip3 install dtschema --upgrade >> >> Please check and re-submit after running the above command yourself. Note >> that DT_SCHEMA_FILES can be set to your schema file to speed up checking >> your schema. However, it must be unset to test all examples with your schema. >> > > Thanks for the reviews. After running make dt_binding_check for it > seems like hours (on a dual-core 1.8GHz ARM box), I got impatient and > used > make CHECK_DTBS=y armada-385-thecus-n2350.dtb > > I'll move this to another faster box and run make dt_binding_check. So many questions... 1. Why do you have to run it on arm? Not on regular machine for work? No one of us does like that... 2. You are now mixing now two different commands. You were asked to run DT_SCHEMA_FILES 3. Read the provided guide how to speed it up. It runs within few seconds. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x @ 2023-04-13 7:51 ` Krzysztof Kozlowski 0 siblings, 0 replies; 24+ messages in thread From: Krzysztof Kozlowski @ 2023-04-13 7:51 UTC (permalink / raw) To: Tony Dinh, Rob Herring Cc: Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth On 12/04/2023 21:05, Tony Dinh wrote: > Hi Rob, > Hi Krzysztof, > > On Wed, Apr 12, 2023 at 5:36 AM Rob Herring <robh@kernel.org> wrote: >> >> >> On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: >>> Add device tree binding for Marvell Armada 38x. >>> >>> Signed-off-by: Tony Dinh <mibodhi@gmail.com> >>> --- >>> >>> Changes in v2: >>> - Add marvell,38x.yaml. For now, add this binding to the Marvell >>> directory to keep it consistent with other Marvell yaml files. >>> At a later date and a separate patch, consolidate the Marvell >>> yaml files into marvell.yaml. >>> >>> .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ >>> 1 file changed, 27 insertions(+) >>> create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml >>> >> >> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' >> on your patch (DT_CHECKER_FLAGS is new in v5.13): >> >> yamllint warnings/errors: >> >> dtschema/dtc warnings/errors: >> ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename >> expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# >> >> doc reference errors (make refcheckdocs): >> >> See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com >> >> The base for the series is generally the latest rc1. A different dependency >> should be noted in *this* patch. >> >> If you already ran 'make dt_binding_check' and didn't see the above >> error(s), then make sure 'yamllint' is installed and dt-schema is up to >> date: >> >> pip3 install dtschema --upgrade >> >> Please check and re-submit after running the above command yourself. Note >> that DT_SCHEMA_FILES can be set to your schema file to speed up checking >> your schema. However, it must be unset to test all examples with your schema. >> > > Thanks for the reviews. After running make dt_binding_check for it > seems like hours (on a dual-core 1.8GHz ARM box), I got impatient and > used > make CHECK_DTBS=y armada-385-thecus-n2350.dtb > > I'll move this to another faster box and run make dt_binding_check. So many questions... 1. Why do you have to run it on arm? Not on regular machine for work? No one of us does like that... 2. You are now mixing now two different commands. You were asked to run DT_SCHEMA_FILES 3. Read the provided guide how to speed it up. It runs within few seconds. Best regards, Krzysztof _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x 2023-04-13 7:51 ` Krzysztof Kozlowski @ 2023-04-13 19:12 ` Tony Dinh -1 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-13 19:12 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth Hi Krzysztof, On Thu, Apr 13, 2023 at 12:51 AM Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 12/04/2023 21:05, Tony Dinh wrote: > > Hi Rob, > > Hi Krzysztof, > > > > On Wed, Apr 12, 2023 at 5:36 AM Rob Herring <robh@kernel.org> wrote: > >> > >> > >> On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: > >>> Add device tree binding for Marvell Armada 38x. > >>> > >>> Signed-off-by: Tony Dinh <mibodhi@gmail.com> > >>> --- > >>> > >>> Changes in v2: > >>> - Add marvell,38x.yaml. For now, add this binding to the Marvell > >>> directory to keep it consistent with other Marvell yaml files. > >>> At a later date and a separate patch, consolidate the Marvell > >>> yaml files into marvell.yaml. > >>> > >>> .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ > >>> 1 file changed, 27 insertions(+) > >>> create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > >>> > >> > >> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > >> on your patch (DT_CHECKER_FLAGS is new in v5.13): > >> > >> yamllint warnings/errors: > >> > >> dtschema/dtc warnings/errors: > >> ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename > >> expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# > >> > >> doc reference errors (make refcheckdocs): > >> > >> See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com > >> > >> The base for the series is generally the latest rc1. A different dependency > >> should be noted in *this* patch. > >> > >> If you already ran 'make dt_binding_check' and didn't see the above > >> error(s), then make sure 'yamllint' is installed and dt-schema is up to > >> date: > >> > >> pip3 install dtschema --upgrade > >> > >> Please check and re-submit after running the above command yourself. Note > >> that DT_SCHEMA_FILES can be set to your schema file to speed up checking > >> your schema. However, it must be unset to test all examples with your schema. > >> > > > > Thanks for the reviews. After running make dt_binding_check for it > > seems like hours (on a dual-core 1.8GHz ARM box), I got impatient and > > used > > make CHECK_DTBS=y armada-385-thecus-n2350.dtb > > > > I'll move this to another faster box and run make dt_binding_check. > > So many questions... > 1. Why do you have to run it on arm? Not on regular machine for work? No > one of us does like that... It's just more convenient for me to run on ARM (I also build ARM kernels natively with distcc). This is not work related, so I cannot use machines at work. I can use my personal 4-core laptop, though. > 2. You are now mixing now two different commands. You were asked to run > DT_SCHEMA_FILES OK. As you can see, I have no experience with schema before. > 3. Read the provided guide how to speed it up. It runs within few seconds. Good to know there is a way. Thanks for the advice! All the best, Tony > > > Best regards, > Krzysztof > ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x @ 2023-04-13 19:12 ` Tony Dinh 0 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-13 19:12 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Rob Herring, Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth Hi Krzysztof, On Thu, Apr 13, 2023 at 12:51 AM Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 12/04/2023 21:05, Tony Dinh wrote: > > Hi Rob, > > Hi Krzysztof, > > > > On Wed, Apr 12, 2023 at 5:36 AM Rob Herring <robh@kernel.org> wrote: > >> > >> > >> On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: > >>> Add device tree binding for Marvell Armada 38x. > >>> > >>> Signed-off-by: Tony Dinh <mibodhi@gmail.com> > >>> --- > >>> > >>> Changes in v2: > >>> - Add marvell,38x.yaml. For now, add this binding to the Marvell > >>> directory to keep it consistent with other Marvell yaml files. > >>> At a later date and a separate patch, consolidate the Marvell > >>> yaml files into marvell.yaml. > >>> > >>> .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ > >>> 1 file changed, 27 insertions(+) > >>> create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > >>> > >> > >> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > >> on your patch (DT_CHECKER_FLAGS is new in v5.13): > >> > >> yamllint warnings/errors: > >> > >> dtschema/dtc warnings/errors: > >> ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename > >> expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# > >> > >> doc reference errors (make refcheckdocs): > >> > >> See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com > >> > >> The base for the series is generally the latest rc1. A different dependency > >> should be noted in *this* patch. > >> > >> If you already ran 'make dt_binding_check' and didn't see the above > >> error(s), then make sure 'yamllint' is installed and dt-schema is up to > >> date: > >> > >> pip3 install dtschema --upgrade > >> > >> Please check and re-submit after running the above command yourself. Note > >> that DT_SCHEMA_FILES can be set to your schema file to speed up checking > >> your schema. However, it must be unset to test all examples with your schema. > >> > > > > Thanks for the reviews. After running make dt_binding_check for it > > seems like hours (on a dual-core 1.8GHz ARM box), I got impatient and > > used > > make CHECK_DTBS=y armada-385-thecus-n2350.dtb > > > > I'll move this to another faster box and run make dt_binding_check. > > So many questions... > 1. Why do you have to run it on arm? Not on regular machine for work? No > one of us does like that... It's just more convenient for me to run on ARM (I also build ARM kernels natively with distcc). This is not work related, so I cannot use machines at work. I can use my personal 4-core laptop, though. > 2. You are now mixing now two different commands. You were asked to run > DT_SCHEMA_FILES OK. As you can see, I have no experience with schema before. > 3. Read the provided guide how to speed it up. It runs within few seconds. Good to know there is a way. Thanks for the advice! All the best, Tony > > > Best regards, > Krzysztof > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x 2023-04-12 12:36 ` Rob Herring @ 2023-05-01 22:46 ` Tony Dinh -1 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-05-01 22:46 UTC (permalink / raw) To: Rob Herring Cc: Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth Hi Rob, On Wed, Apr 12, 2023 at 5:36 AM Rob Herring <robh@kernel.org> wrote: > > > On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: > > Add device tree binding for Marvell Armada 38x. > > > > Signed-off-by: Tony Dinh <mibodhi@gmail.com> > > --- > > > > Changes in v2: > > - Add marvell,38x.yaml. For now, add this binding to the Marvell > > directory to keep it consistent with other Marvell yaml files. > > At a later date and a separate patch, consolidate the Marvell > > yaml files into marvell.yaml. > > > > .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ > > 1 file changed, 27 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > > > > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > yamllint warnings/errors: > > dtschema/dtc warnings/errors: > ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename > expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# > > doc reference errors (make refcheckdocs): > > See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com > > The base for the series is generally the latest rc1. A different dependency > should be noted in *this* patch. > > If you already ran 'make dt_binding_check' and didn't see the above > error(s), then make sure 'yamllint' is installed and dt-schema is up to > date: > > pip3 install dtschema --upgrade > > Please check and re-submit after running the above command yourself. Note > that DT_SCHEMA_FILES can be set to your schema file to speed up checking > your schema. However, it must be unset to test all examples with your schema. > Would dt-schema in Debian 12 work? or must it be the latest dtschema installed by pip3 or from GitHub? Thanks, Tony ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x @ 2023-05-01 22:46 ` Tony Dinh 0 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-05-01 22:46 UTC (permalink / raw) To: Rob Herring Cc: Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth Hi Rob, On Wed, Apr 12, 2023 at 5:36 AM Rob Herring <robh@kernel.org> wrote: > > > On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: > > Add device tree binding for Marvell Armada 38x. > > > > Signed-off-by: Tony Dinh <mibodhi@gmail.com> > > --- > > > > Changes in v2: > > - Add marvell,38x.yaml. For now, add this binding to the Marvell > > directory to keep it consistent with other Marvell yaml files. > > At a later date and a separate patch, consolidate the Marvell > > yaml files into marvell.yaml. > > > > .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ > > 1 file changed, 27 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml > > > > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > yamllint warnings/errors: > > dtschema/dtc warnings/errors: > ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename > expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# > > doc reference errors (make refcheckdocs): > > See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com > > The base for the series is generally the latest rc1. A different dependency > should be noted in *this* patch. > > If you already ran 'make dt_binding_check' and didn't see the above > error(s), then make sure 'yamllint' is installed and dt-schema is up to > date: > > pip3 install dtschema --upgrade > > Please check and re-submit after running the above command yourself. Note > that DT_SCHEMA_FILES can be set to your schema file to speed up checking > your schema. However, it must be unset to test all examples with your schema. > Would dt-schema in Debian 12 work? or must it be the latest dtschema installed by pip3 or from GitHub? Thanks, Tony _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x 2023-05-01 22:46 ` Tony Dinh @ 2023-05-02 6:54 ` Krzysztof Kozlowski -1 siblings, 0 replies; 24+ messages in thread From: Krzysztof Kozlowski @ 2023-05-02 6:54 UTC (permalink / raw) To: Tony Dinh, Rob Herring Cc: Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth On 02/05/2023 00:46, Tony Dinh wrote: > Hi Rob, > > On Wed, Apr 12, 2023 at 5:36 AM Rob Herring <robh@kernel.org> wrote: >> >> >> On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: >>> Add device tree binding for Marvell Armada 38x. >>> >>> Signed-off-by: Tony Dinh <mibodhi@gmail.com> >>> --- >>> >>> Changes in v2: >>> - Add marvell,38x.yaml. For now, add this binding to the Marvell >>> directory to keep it consistent with other Marvell yaml files. >>> At a later date and a separate patch, consolidate the Marvell >>> yaml files into marvell.yaml. >>> >>> .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ >>> 1 file changed, 27 insertions(+) >>> create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml >>> >> >> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' >> on your patch (DT_CHECKER_FLAGS is new in v5.13): >> >> yamllint warnings/errors: >> >> dtschema/dtc warnings/errors: >> ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename >> expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# >> >> doc reference errors (make refcheckdocs): >> >> See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com >> >> The base for the series is generally the latest rc1. A different dependency >> should be noted in *this* patch. >> >> If you already ran 'make dt_binding_check' and didn't see the above >> error(s), then make sure 'yamllint' is installed and dt-schema is up to >> date: >> >> pip3 install dtschema --upgrade >> >> Please check and re-submit after running the above command yourself. Note >> that DT_SCHEMA_FILES can be set to your schema file to speed up checking >> your schema. However, it must be unset to test all examples with your schema. >> > > Would dt-schema in Debian 12 work? or must it be the latest dtschema > installed by pip3 or from GitHub? If Debian 12 has latest schema, it would work. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x @ 2023-05-02 6:54 ` Krzysztof Kozlowski 0 siblings, 0 replies; 24+ messages in thread From: Krzysztof Kozlowski @ 2023-05-02 6:54 UTC (permalink / raw) To: Tony Dinh, Rob Herring Cc: Gregory Clement, Rob Herring, linux-arm-kernel, linux-kernel, Krzysztof Kozlowski, devicetree, Andrew Lunn, Sebastian Hesselbarth On 02/05/2023 00:46, Tony Dinh wrote: > Hi Rob, > > On Wed, Apr 12, 2023 at 5:36 AM Rob Herring <robh@kernel.org> wrote: >> >> >> On Tue, 11 Apr 2023 19:57:35 -0700, Tony Dinh wrote: >>> Add device tree binding for Marvell Armada 38x. >>> >>> Signed-off-by: Tony Dinh <mibodhi@gmail.com> >>> --- >>> >>> Changes in v2: >>> - Add marvell,38x.yaml. For now, add this binding to the Marvell >>> directory to keep it consistent with other Marvell yaml files. >>> At a later date and a separate patch, consolidate the Marvell >>> yaml files into marvell.yaml. >>> >>> .../bindings/arm/marvell/armada-38x.yaml | 27 +++++++++++++++++++ >>> 1 file changed, 27 insertions(+) >>> create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml >>> >> >> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' >> on your patch (DT_CHECKER_FLAGS is new in v5.13): >> >> yamllint warnings/errors: >> >> dtschema/dtc warnings/errors: >> ./Documentation/devicetree/bindings/arm/marvell/armada-38x.yaml: $id: relative path/filename doesn't match actual path or filename >> expected: http://devicetree.org/schemas/arm/marvell/armada-38x.yaml# >> >> doc reference errors (make refcheckdocs): >> >> See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230412025737.20280-2-mibodhi@gmail.com >> >> The base for the series is generally the latest rc1. A different dependency >> should be noted in *this* patch. >> >> If you already ran 'make dt_binding_check' and didn't see the above >> error(s), then make sure 'yamllint' is installed and dt-schema is up to >> date: >> >> pip3 install dtschema --upgrade >> >> Please check and re-submit after running the above command yourself. Note >> that DT_SCHEMA_FILES can be set to your schema file to speed up checking >> your schema. However, it must be unset to test all examples with your schema. >> > > Would dt-schema in Debian 12 work? or must it be the latest dtschema > installed by pip3 or from GitHub? If Debian 12 has latest schema, it would work. Best regards, Krzysztof _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v2 2/2] ARM: dts: mvebu: add Thecus N2350 board DTS 2023-04-12 2:57 ` Tony Dinh @ 2023-04-12 2:57 ` Tony Dinh -1 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-12 2:57 UTC (permalink / raw) To: Andrew Lunn, Gregory Clement, devicetree, linux-arm-kernel Cc: Tony Dinh, Arnd Bergmann, Krzysztof Kozlowski, Olof Johansson, Rob Herring, Sebastian Hesselbarth, linux-kernel, soc Add Thecus N2350 board DTS and Makefile. Signed-off-by: Tony Dinh <mibodhi@gmail.com> --- Changes in v2: - Fix various DT bindings conformance (too numerous to list) - Vendor prefix is not necessary, so remove it. arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/armada-385-thecus-n2350.dts | 432 ++++++++++++++++++ 2 files changed, 433 insertions(+) create mode 100644 arch/arm/boot/dts/armada-385-thecus-n2350.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index efe4152e5846..cc856a57e58d 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1535,6 +1535,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \ armada-385-linksys-rango.dtb \ armada-385-linksys-shelby.dtb \ armada-385-synology-ds116.dtb \ + armada-385-thecus-n2350.dtb \ armada-385-turris-omnia.dtb \ armada-388-clearfog.dtb \ armada-388-clearfog-base.dtb \ diff --git a/arch/arm/boot/dts/armada-385-thecus-n2350.dts b/arch/arm/boot/dts/armada-385-thecus-n2350.dts new file mode 100644 index 000000000000..54f1eab770a4 --- /dev/null +++ b/arch/arm/boot/dts/armada-385-thecus-n2350.dts @@ -0,0 +1,432 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Device Tree file for Thecus N2350 board + * + * Copyright (C) 2018-2023 Tony Dinh <mibodhi@gmail.com> + * Copyright (C) 2018 Manuel Jung <manuel.jung@hotmail.com> + */ + +/dts-v1/; +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include "armada-385.dtsi" + +/ { + model = "Thecus N2350"; + compatible = "marvell,armada385"; + + aliases { + ethernet0 = ð0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x40000000>; /* 1GB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000 + MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000 + MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>; + + }; + + usb3_0_phy: usb-phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <&usb3_0_power>; + #phy-cells = <0>; + }; + + usb3_1_phy: usb-phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <&usb3_1_power>; + #phy-cells = <0>; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&pmx_power_button &pmx_copy_button &pmx_reset_button>; + pinctrl-names = "default"; + + button-1 { + label = "Power Button"; + linux,code = <KEY_POWER>; + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + }; + + button-2 { + label = "Copy Button"; + linux,code = <KEY_COPY>; + gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>; + }; + + button-3 { + label = "Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_sata1_white_led + &pmx_sata1_red_led + &pmx_sata2_white_led + &pmx_sata2_red_led + &pmx_sys_white_led + &pmx_sys_red_led + &pmx_pwr_blue_led + &pmx_pwr_red_led + &pmx_usb_white_led + &pmx_usb_red_led>; + + pinctrl-names = "default"; + + led-1 { + label = "n2350:white:sata1"; + gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>; + }; + + led-2 { + label = "n2350:red:sata1"; + gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>; + }; + + led-3 { + label = "n2350:white:sata2"; + gpios = <&gpio0 19 GPIO_ACTIVE_HIGH>; + }; + + led-4 { + label = "n2350:red:sata2"; + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + }; + + led-5 { + label = "n2350:white:sys"; + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + + led-6 { + label = "n2350:red:sys"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + + led-7 { + label = "n2350:blue:pwr"; + gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; + }; + + led-8 { + label = "n2350:red:pwr"; + gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; + }; + + led-9 { + label = "n2350:white:usb"; + gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + }; + + led-10 { + label = "n2350:red:usb"; + gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>; + }; + }; + + usb3_0_power: v5-vbus0 { + compatible = "regulator-fixed"; + regulator-name = "USB3_0_Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>; + }; + + usb3_1_power: v5-vbus1 { + compatible = "regulator-fixed"; + regulator-name = "USB3_1_Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>; + }; + + reg_sata0: pwr-sata0 { + compatible = "regulator-fixed"; + regulator-name = "pwr_en_sata0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + + reg_5v_sata0: v5-sata0 { + compatible = "regulator-fixed"; + regulator-name = "v5.0-sata0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <®_sata0>; + }; + + reg_12v_sata0: v12-sata0 { + compatible = "regulator-fixed"; + regulator-name = "v12.0-sata0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + vin-supply = <®_sata0>; + }; + + reg_sata1: pwr-sata0 { + regulator-name = "pwr_en_sata1"; + compatible = "regulator-fixed"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + + reg_5v_sata1: v5-sata1 { + compatible = "regulator-fixed"; + regulator-name = "v5.0-sata1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <®_sata1>; + }; + + reg_12v_sata1: v12-sata1 { + compatible = "regulator-fixed"; + regulator-name = "v12.0-sata1"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + vin-supply = <®_sata1>; + }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + pinctrl-0 = <&pmx_pwr_off>; + pinctrl-names = "default"; + gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; + }; + +}; + +&ahci0 { + status = "okay"; +}; + +&bm { + status = "okay"; +}; + +&bm_bppi { + status = "okay"; +}; + +ð0 { + status = "okay"; + phy = <&phy0>; + phy-mode = "sgmii"; + buffer-manager = <&bm>; + bm,pool-long = <0>; + bm,pool-short = <1>; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <100000>; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <100000>; +}; + +&mdio { + phy0: ethernet-phy@0 { + reg = <1>; + }; +}; + +&nand_controller { + status = "okay"; + + nand@0 { + status = "okay"; + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "rootfs"; + reg = <0x00000000 0x20000000>; + }; + + }; + }; +}; + +&pciec { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; + +&pinctrl { + pinctrl-names = "default"; + + pmx_power_button: pmx-power-button { + marvell,pins = "mpp49"; + marvell,function = "gpio"; + }; + + pmx_copy_button: pmx-copy-button { + marvell,pins = "mpp52"; + marvell,function = "gpio"; + }; + + pmx_reset_button: pmx-reset-button { + marvell,pins = "mpp50"; + marvell,function = "gpio"; + }; + + pmx_sata1_white_led: pmx-sata1-white-led { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + + pmx_sata1_red_led: pmx-sata1-red-led { + marvell,pins = "mpp46"; + marvell,function = "gpio"; + }; + + pmx_sata2_white_led: pmx-sata2-white-led { + marvell,pins = "mpp19"; + marvell,function = "gpio"; + }; + + pmx_sata2_red_led: pmx-sata2-red-led { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + + pmx_sys_white_led: pmx-sys-white-led { + marvell,pins = "mpp14"; + marvell,function = "gpio"; + }; + + pmx_sys_red_led: pmx-sys-red-led { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_buzzer: pmx-buzzer { + marvell,pins = "mpp51"; + marvell,function = "gpio"; + }; + + pmx_pwr_off: pmx-pwr-off { + marvell,pins = "mpp54"; + marvell,function = "gpio"; + }; + + pmx_pwr_blue_led: pmx-pwr-blue-led { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + + pmx_pwr_red_led: pmx-pwr-red-led { + marvell,pins = "mpp18"; + marvell,function = "gpio"; + }; + + pmx_usb_white_led: pmx-usb-white-led { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_usb_red_led: pmx-usb-red-led { + marvell,pins = "mpp17"; + marvell,function = "gpio"; + }; +}; + +&sdhci { + broken-cd; + wp-inverted; + bus-width = <8>; + status = "okay"; + no-1-8-v; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins>; + status = "okay"; + + /* spi: 4M Flash Macronix MX25L3205D */ + flash@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "jedec,spi-nor"; + reg = <0>; + + spi-max-frequency = <108000000>; + spi-cpha; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x00100000>; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x00100000 0x00010000>; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; -- 2.30.2 ^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 2/2] ARM: dts: mvebu: add Thecus N2350 board DTS @ 2023-04-12 2:57 ` Tony Dinh 0 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-12 2:57 UTC (permalink / raw) To: Andrew Lunn, Gregory Clement, devicetree, linux-arm-kernel Cc: Tony Dinh, Arnd Bergmann, Krzysztof Kozlowski, Olof Johansson, Rob Herring, Sebastian Hesselbarth, linux-kernel, soc Add Thecus N2350 board DTS and Makefile. Signed-off-by: Tony Dinh <mibodhi@gmail.com> --- Changes in v2: - Fix various DT bindings conformance (too numerous to list) - Vendor prefix is not necessary, so remove it. arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/armada-385-thecus-n2350.dts | 432 ++++++++++++++++++ 2 files changed, 433 insertions(+) create mode 100644 arch/arm/boot/dts/armada-385-thecus-n2350.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index efe4152e5846..cc856a57e58d 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1535,6 +1535,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \ armada-385-linksys-rango.dtb \ armada-385-linksys-shelby.dtb \ armada-385-synology-ds116.dtb \ + armada-385-thecus-n2350.dtb \ armada-385-turris-omnia.dtb \ armada-388-clearfog.dtb \ armada-388-clearfog-base.dtb \ diff --git a/arch/arm/boot/dts/armada-385-thecus-n2350.dts b/arch/arm/boot/dts/armada-385-thecus-n2350.dts new file mode 100644 index 000000000000..54f1eab770a4 --- /dev/null +++ b/arch/arm/boot/dts/armada-385-thecus-n2350.dts @@ -0,0 +1,432 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Device Tree file for Thecus N2350 board + * + * Copyright (C) 2018-2023 Tony Dinh <mibodhi@gmail.com> + * Copyright (C) 2018 Manuel Jung <manuel.jung@hotmail.com> + */ + +/dts-v1/; +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include "armada-385.dtsi" + +/ { + model = "Thecus N2350"; + compatible = "marvell,armada385"; + + aliases { + ethernet0 = ð0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x40000000>; /* 1GB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000 + MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000 + MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>; + + }; + + usb3_0_phy: usb-phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <&usb3_0_power>; + #phy-cells = <0>; + }; + + usb3_1_phy: usb-phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <&usb3_1_power>; + #phy-cells = <0>; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&pmx_power_button &pmx_copy_button &pmx_reset_button>; + pinctrl-names = "default"; + + button-1 { + label = "Power Button"; + linux,code = <KEY_POWER>; + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + }; + + button-2 { + label = "Copy Button"; + linux,code = <KEY_COPY>; + gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>; + }; + + button-3 { + label = "Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_sata1_white_led + &pmx_sata1_red_led + &pmx_sata2_white_led + &pmx_sata2_red_led + &pmx_sys_white_led + &pmx_sys_red_led + &pmx_pwr_blue_led + &pmx_pwr_red_led + &pmx_usb_white_led + &pmx_usb_red_led>; + + pinctrl-names = "default"; + + led-1 { + label = "n2350:white:sata1"; + gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>; + }; + + led-2 { + label = "n2350:red:sata1"; + gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>; + }; + + led-3 { + label = "n2350:white:sata2"; + gpios = <&gpio0 19 GPIO_ACTIVE_HIGH>; + }; + + led-4 { + label = "n2350:red:sata2"; + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + }; + + led-5 { + label = "n2350:white:sys"; + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + + led-6 { + label = "n2350:red:sys"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + + led-7 { + label = "n2350:blue:pwr"; + gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; + }; + + led-8 { + label = "n2350:red:pwr"; + gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; + }; + + led-9 { + label = "n2350:white:usb"; + gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + }; + + led-10 { + label = "n2350:red:usb"; + gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>; + }; + }; + + usb3_0_power: v5-vbus0 { + compatible = "regulator-fixed"; + regulator-name = "USB3_0_Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>; + }; + + usb3_1_power: v5-vbus1 { + compatible = "regulator-fixed"; + regulator-name = "USB3_1_Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>; + }; + + reg_sata0: pwr-sata0 { + compatible = "regulator-fixed"; + regulator-name = "pwr_en_sata0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + + reg_5v_sata0: v5-sata0 { + compatible = "regulator-fixed"; + regulator-name = "v5.0-sata0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <®_sata0>; + }; + + reg_12v_sata0: v12-sata0 { + compatible = "regulator-fixed"; + regulator-name = "v12.0-sata0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + vin-supply = <®_sata0>; + }; + + reg_sata1: pwr-sata0 { + regulator-name = "pwr_en_sata1"; + compatible = "regulator-fixed"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + + reg_5v_sata1: v5-sata1 { + compatible = "regulator-fixed"; + regulator-name = "v5.0-sata1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <®_sata1>; + }; + + reg_12v_sata1: v12-sata1 { + compatible = "regulator-fixed"; + regulator-name = "v12.0-sata1"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + vin-supply = <®_sata1>; + }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + pinctrl-0 = <&pmx_pwr_off>; + pinctrl-names = "default"; + gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; + }; + +}; + +&ahci0 { + status = "okay"; +}; + +&bm { + status = "okay"; +}; + +&bm_bppi { + status = "okay"; +}; + +ð0 { + status = "okay"; + phy = <&phy0>; + phy-mode = "sgmii"; + buffer-manager = <&bm>; + bm,pool-long = <0>; + bm,pool-short = <1>; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <100000>; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <100000>; +}; + +&mdio { + phy0: ethernet-phy@0 { + reg = <1>; + }; +}; + +&nand_controller { + status = "okay"; + + nand@0 { + status = "okay"; + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "rootfs"; + reg = <0x00000000 0x20000000>; + }; + + }; + }; +}; + +&pciec { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; + +&pinctrl { + pinctrl-names = "default"; + + pmx_power_button: pmx-power-button { + marvell,pins = "mpp49"; + marvell,function = "gpio"; + }; + + pmx_copy_button: pmx-copy-button { + marvell,pins = "mpp52"; + marvell,function = "gpio"; + }; + + pmx_reset_button: pmx-reset-button { + marvell,pins = "mpp50"; + marvell,function = "gpio"; + }; + + pmx_sata1_white_led: pmx-sata1-white-led { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + + pmx_sata1_red_led: pmx-sata1-red-led { + marvell,pins = "mpp46"; + marvell,function = "gpio"; + }; + + pmx_sata2_white_led: pmx-sata2-white-led { + marvell,pins = "mpp19"; + marvell,function = "gpio"; + }; + + pmx_sata2_red_led: pmx-sata2-red-led { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + + pmx_sys_white_led: pmx-sys-white-led { + marvell,pins = "mpp14"; + marvell,function = "gpio"; + }; + + pmx_sys_red_led: pmx-sys-red-led { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_buzzer: pmx-buzzer { + marvell,pins = "mpp51"; + marvell,function = "gpio"; + }; + + pmx_pwr_off: pmx-pwr-off { + marvell,pins = "mpp54"; + marvell,function = "gpio"; + }; + + pmx_pwr_blue_led: pmx-pwr-blue-led { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + + pmx_pwr_red_led: pmx-pwr-red-led { + marvell,pins = "mpp18"; + marvell,function = "gpio"; + }; + + pmx_usb_white_led: pmx-usb-white-led { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_usb_red_led: pmx-usb-red-led { + marvell,pins = "mpp17"; + marvell,function = "gpio"; + }; +}; + +&sdhci { + broken-cd; + wp-inverted; + bus-width = <8>; + status = "okay"; + no-1-8-v; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins>; + status = "okay"; + + /* spi: 4M Flash Macronix MX25L3205D */ + flash@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "jedec,spi-nor"; + reg = <0>; + + spi-max-frequency = <108000000>; + spi-cpha; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x00100000>; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x00100000 0x00010000>; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; -- 2.30.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 24+ messages in thread
* Re: [PATCH v2 2/2] ARM: dts: mvebu: add Thecus N2350 board DTS 2023-04-12 2:57 ` Tony Dinh @ 2023-04-12 12:24 ` Andrew Lunn -1 siblings, 0 replies; 24+ messages in thread From: Andrew Lunn @ 2023-04-12 12:24 UTC (permalink / raw) To: Tony Dinh Cc: Gregory Clement, devicetree, linux-arm-kernel, Arnd Bergmann, Krzysztof Kozlowski, Olof Johansson, Rob Herring, Sebastian Hesselbarth, linux-kernel, soc > + > +/ { > + model = "Thecus N2350"; > + compatible = "marvell,armada385"; If you look at all the other armarda-385 .dts files, they all have a board compatible. It might not be needed now, but it could be useful in the future and allow backwards compatibility. > +&mdio { > + phy0: ethernet-phy@0 { > + reg = <1>; > + }; > +}; Since you have ref = <1>, this should be ethernet-phy@1. ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 2/2] ARM: dts: mvebu: add Thecus N2350 board DTS @ 2023-04-12 12:24 ` Andrew Lunn 0 siblings, 0 replies; 24+ messages in thread From: Andrew Lunn @ 2023-04-12 12:24 UTC (permalink / raw) To: Tony Dinh Cc: Gregory Clement, devicetree, linux-arm-kernel, Arnd Bergmann, Krzysztof Kozlowski, Olof Johansson, Rob Herring, Sebastian Hesselbarth, linux-kernel, soc > + > +/ { > + model = "Thecus N2350"; > + compatible = "marvell,armada385"; If you look at all the other armarda-385 .dts files, they all have a board compatible. It might not be needed now, but it could be useful in the future and allow backwards compatibility. > +&mdio { > + phy0: ethernet-phy@0 { > + reg = <1>; > + }; > +}; Since you have ref = <1>, this should be ethernet-phy@1. _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 2/2] ARM: dts: mvebu: add Thecus N2350 board DTS 2023-04-12 12:24 ` Andrew Lunn @ 2023-04-12 18:50 ` Tony Dinh -1 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-12 18:50 UTC (permalink / raw) To: Andrew Lunn Cc: Gregory Clement, devicetree, linux-arm-kernel, Arnd Bergmann, Krzysztof Kozlowski, Olof Johansson, Rob Herring, Sebastian Hesselbarth, linux-kernel, soc Hi Andrew, On Wed, Apr 12, 2023 at 5:24 AM Andrew Lunn <andrew@lunn.ch> wrote: > > > + > > +/ { > > + model = "Thecus N2350"; > > + compatible = "marvell,armada385"; > > If you look at all the other armarda-385 .dts files, they all have a > board compatible. It might not be needed now, but it could be useful > in the future and allow backwards compatibility. > > > +&mdio { > > + phy0: ethernet-phy@0 { > > + reg = <1>; > > + }; > > +}; > > Since you have ref = <1>, this should be ethernet-phy@1. > Thanks! somehow I kept missing that change. All the best, Tony ^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 2/2] ARM: dts: mvebu: add Thecus N2350 board DTS @ 2023-04-12 18:50 ` Tony Dinh 0 siblings, 0 replies; 24+ messages in thread From: Tony Dinh @ 2023-04-12 18:50 UTC (permalink / raw) To: Andrew Lunn Cc: Gregory Clement, devicetree, linux-arm-kernel, Arnd Bergmann, Krzysztof Kozlowski, Olof Johansson, Rob Herring, Sebastian Hesselbarth, linux-kernel, soc Hi Andrew, On Wed, Apr 12, 2023 at 5:24 AM Andrew Lunn <andrew@lunn.ch> wrote: > > > + > > +/ { > > + model = "Thecus N2350"; > > + compatible = "marvell,armada385"; > > If you look at all the other armarda-385 .dts files, they all have a > board compatible. It might not be needed now, but it could be useful > in the future and allow backwards compatibility. > > > +&mdio { > > + phy0: ethernet-phy@0 { > > + reg = <1>; > > + }; > > +}; > > Since you have ref = <1>, this should be ethernet-phy@1. > Thanks! somehow I kept missing that change. All the best, Tony _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 24+ messages in thread
end of thread, other threads:[~2023-05-02 6:55 UTC | newest] Thread overview: 24+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2023-04-12 2:57 [PATCH v2 0/2] Add support for Thecus N2350 board Tony Dinh 2023-04-12 2:57 ` Tony Dinh 2023-04-12 2:57 ` [PATCH v2 1/2] ARM: dts: mvebu: Add device tree binding for Marvell Armada 38x Tony Dinh 2023-04-12 2:57 ` Tony Dinh 2023-04-12 7:13 ` Krzysztof Kozlowski 2023-04-12 7:13 ` Krzysztof Kozlowski 2023-04-12 12:36 ` Rob Herring 2023-04-12 12:36 ` Rob Herring 2023-04-12 19:05 ` Tony Dinh 2023-04-12 19:05 ` Tony Dinh 2023-04-13 7:51 ` Krzysztof Kozlowski 2023-04-13 7:51 ` Krzysztof Kozlowski 2023-04-13 19:12 ` Tony Dinh 2023-04-13 19:12 ` Tony Dinh 2023-05-01 22:46 ` Tony Dinh 2023-05-01 22:46 ` Tony Dinh 2023-05-02 6:54 ` Krzysztof Kozlowski 2023-05-02 6:54 ` Krzysztof Kozlowski 2023-04-12 2:57 ` [PATCH v2 2/2] ARM: dts: mvebu: add Thecus N2350 board DTS Tony Dinh 2023-04-12 2:57 ` Tony Dinh 2023-04-12 12:24 ` Andrew Lunn 2023-04-12 12:24 ` Andrew Lunn 2023-04-12 18:50 ` Tony Dinh 2023-04-12 18:50 ` Tony Dinh
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.