[PATCH RFC] net: dsa: remove unnecessary phy.h include

[PATCH RFC] net: dsa: remove unnecessary phy.h include

[Russell King - ARM Linux]

Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel.  There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.

Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.

This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
I noticed when I touched linux/phy.h that a lot of the kernel ended up
being unexpectedly rebuilt, as linux/netdevice.h includes net/dsa.h,
which then then includes linux/phy.h.  I've tested this change on both
ARM and ARM64, but I'd suggest letting the 0-day builder have a bite
at this, and then only taking it if everyone is confident that there's
a slim chance of any problems.  Also, it may need some rework to apply
to davem's tree.  All of the above makes this RFC only.

 drivers/net/dsa/mv88e6xxx/mv88e6xxx.h | 1 +
 include/net/dsa.h                     | 6 ++++--
 2 files changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h b/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
index a319c06d82e3..d247b0639ed4 100644
--- a/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
+++ b/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
@@ -15,6 +15,7 @@
 #include <linux/if_vlan.h>
 #include <linux/irq.h>
 #include <linux/gpio/consumer.h>
+#include <linux/phy.h>
 
 #ifndef UINT64_MAX
 #define UINT64_MAX		(u64)(~((u64)0))
diff --git a/include/net/dsa.h b/include/net/dsa.h
index b122196d5a1f..887b2f98f9ea 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -11,15 +11,17 @@
 #ifndef __LINUX_NET_DSA_H
 #define __LINUX_NET_DSA_H
 
+#include <linux/if.h>
 #include <linux/if_ether.h>
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/workqueue.h>
 #include <linux/of.h>
-#include <linux/phy.h>
-#include <linux/phy_fixed.h>
 #include <linux/ethtool.h>
 
+struct phy_device;
+struct fixed_phy_status;
+
 enum dsa_tag_protocol {
 	DSA_TAG_PROTO_NONE = 0,
 	DSA_TAG_PROTO_DSA,

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH RFC] net: dsa: remove unnecessary phy.h include

[Vivien Didelot]

Hi Russell,

Russell King - ARM Linux <linux@armlinux.org.uk> writes:

> Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
> unnecessary dependency for quite a large amount of the kernel.  There's
> very little which actually requires definitions from phy.h in net/dsa.h
> - the include itself only wants the declaration of a couple of
> structures and IFNAMSIZ.
>
> Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
> mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
> and phy_fixed.h from net/dsa.h.
>
> This patch reduces from around 800 files rebuilt to around 40 - even
> with ccache, the time difference is noticable.
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

This patch applies cleanly on net-next and builds correctly after
touching include/linux/phy.h. My boards work fine with it.

Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>

Thanks,

        Vivien

Re: [PATCH RFC] net: dsa: remove unnecessary phy.h include

[Florian Fainelli]

On 01/17/2017 04:14 PM, Russell King - ARM Linux wrote:
> Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
> unnecessary dependency for quite a large amount of the kernel.  There's
> very little which actually requires definitions from phy.h in net/dsa.h
> - the include itself only wants the declaration of a couple of
> structures and IFNAMSIZ.
> 
> Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
> mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
> and phy_fixed.h from net/dsa.h.
> 
> This patch reduces from around 800 files rebuilt to around 40 - even
> with ccache, the time difference is noticable.
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>

> ---
> I noticed when I touched linux/phy.h that a lot of the kernel ended up
> being unexpectedly rebuilt, as linux/netdevice.h includes net/dsa.h,
> which then then includes linux/phy.h.  I've tested this change on both
> ARM and ARM64, but I'd suggest letting the 0-day builder have a bite
> at this, and then only taking it if everyone is confident that there's
> a slim chance of any problems.  Also, it may need some rework to apply
> to davem's tree.  All of the above makes this RFC only.
> 
>  drivers/net/dsa/mv88e6xxx/mv88e6xxx.h | 1 +
>  include/net/dsa.h                     | 6 ++++--
>  2 files changed, 5 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h b/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
> index a319c06d82e3..d247b0639ed4 100644
> --- a/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
> +++ b/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
> @@ -15,6 +15,7 @@
>  #include <linux/if_vlan.h>
>  #include <linux/irq.h>
>  #include <linux/gpio/consumer.h>
> +#include <linux/phy.h>
>  
>  #ifndef UINT64_MAX
>  #define UINT64_MAX		(u64)(~((u64)0))
> diff --git a/include/net/dsa.h b/include/net/dsa.h
> index b122196d5a1f..887b2f98f9ea 100644
> --- a/include/net/dsa.h
> +++ b/include/net/dsa.h
> @@ -11,15 +11,17 @@
>  #ifndef __LINUX_NET_DSA_H
>  #define __LINUX_NET_DSA_H
>  
> +#include <linux/if.h>
>  #include <linux/if_ether.h>
>  #include <linux/list.h>
>  #include <linux/timer.h>
>  #include <linux/workqueue.h>
>  #include <linux/of.h>
> -#include <linux/phy.h>
> -#include <linux/phy_fixed.h>
>  #include <linux/ethtool.h>
>  
> +struct phy_device;
> +struct fixed_phy_status;
> +
>  enum dsa_tag_protocol {
>  	DSA_TAG_PROTO_NONE = 0,
>  	DSA_TAG_PROTO_DSA,
> 


-- 
Florian

Re: [PATCH RFC] net: dsa: remove unnecessary phy.h include

[David Miller]

From: Russell King - ARM Linux <linux@armlinux.org.uk>
Date: Wed, 18 Jan 2017 00:14:03 +0000

> Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
> unnecessary dependency for quite a large amount of the kernel.  There's
> very little which actually requires definitions from phy.h in net/dsa.h
> - the include itself only wants the declaration of a couple of
> structures and IFNAMSIZ.
> 
> Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
> mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
> and phy_fixed.h from net/dsa.h.
> 
> This patch reduces from around 800 files rebuilt to around 40 - even
> with ccache, the time difference is noticable.
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Applied, thanks.

Re: [PATCH RFC] net: dsa: remove unnecessary phy.h include

[Russell King - ARM Linux]

On Wed, Jan 18, 2017 at 04:37:14PM -0500, David Miller wrote:
> From: Russell King - ARM Linux <linux@armlinux.org.uk>
> Date: Wed, 18 Jan 2017 00:14:03 +0000
> 
> > Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
> > unnecessary dependency for quite a large amount of the kernel.  There's
> > very little which actually requires definitions from phy.h in net/dsa.h
> > - the include itself only wants the declaration of a couple of
> > structures and IFNAMSIZ.
> > 
> > Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
> > mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
> > and phy_fixed.h from net/dsa.h.
> > 
> > This patch reduces from around 800 files rebuilt to around 40 - even
> > with ccache, the time difference is noticable.
> > 
> > Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> 
> Applied, thanks.

Hmm, now that's _really_ interesting.

I think you've said to others to send patches with RFC in them when they
aren't to be applied.  I sent this with RFC in, and it still got applied.

This is _really_ unfortunate, as the 0-day builder has been sending me a
stream of build errors over it, and I now have a branch with 9 patches
plus this one in fixing those errors...

And I did say in the comments below the --- that it should be left a few
days for the 0-day builder to run through it and find those errors.

Ho hum.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

Re: [PATCH RFC] net: dsa: remove unnecessary phy.h include

[David Miller]

From: Russell King - ARM Linux <linux@armlinux.org.uk>
Date: Wed, 18 Jan 2017 21:46:28 +0000

> On Wed, Jan 18, 2017 at 04:37:14PM -0500, David Miller wrote:
>> From: Russell King - ARM Linux <linux@armlinux.org.uk>
>> Date: Wed, 18 Jan 2017 00:14:03 +0000
>> 
>> > Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
>> > unnecessary dependency for quite a large amount of the kernel.  There's
>> > very little which actually requires definitions from phy.h in net/dsa.h
>> > - the include itself only wants the declaration of a couple of
>> > structures and IFNAMSIZ.
>> > 
>> > Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
>> > mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
>> > and phy_fixed.h from net/dsa.h.
>> > 
>> > This patch reduces from around 800 files rebuilt to around 40 - even
>> > with ccache, the time difference is noticable.
>> > 
>> > Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
>> 
>> Applied, thanks.
> 
> Hmm, now that's _really_ interesting.

It got reviewed-by and seemed reasonable.

I am always allowed to use my judgment to turn an RFC into a patch
I actually apply, especially when other developers review the change.

If you read your email now you'll see that I reverted it before
pushing it out, because of the fallout you mention.

Re: [PATCH RFC] net: dsa: remove unnecessary phy.h include

[David Miller]

From: David Miller <davem@davemloft.net>
Date: Wed, 18 Jan 2017 16:37:14 -0500 (EST)

> From: Russell King - ARM Linux <linux@armlinux.org.uk>
> Date: Wed, 18 Jan 2017 00:14:03 +0000
> 
>> Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
>> unnecessary dependency for quite a large amount of the kernel.  There's
>> very little which actually requires definitions from phy.h in net/dsa.h
>> - the include itself only wants the declaration of a couple of
>> structures and IFNAMSIZ.
>> 
>> Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
>> mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
>> and phy_fixed.h from net/dsa.h.
>> 
>> This patch reduces from around 800 files rebuilt to around 40 - even
>> with ccache, the time difference is noticable.
>> 
>> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> 
> Applied, thanks.

Acutallly, I'm reverting this, it breaks the build all over the place.

The problem is that it seems that somehow we are getting an implicit
module.h include via phy.h and this propagates all over the tree.  So
I get failures like:

net/core/netprio_cgroup.c:303:16: error: expected declaration specifiers or ‘...’ before string constant
 MODULE_LICENSE("GPL v2");
 ...
net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function ‘xprt_rdma_bc_put’:
net/sunrpc/xprtrdma/svc_rdma_backchannel.c:277:2: error: implicit declaration of function ‘module_put’ [-Werror=implicit-function-declaration]
  module_put(THIS_MODULE);
  ^
net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function ‘xprt_setup_rdma_bc’:
net/sunrpc/xprtrdma/svc_rdma_backchannel.c:348:7: error: implicit declaration of function ‘try_module_get’ [-Werror=implicit-function-declaration]
  if (!try_module_get(THIS_MODULE))

Please resubmit this after you can successfully complete an allmodconfig build.

Thanks.

[PATCH 4.10-rc3 00/13] net: dsa: remove unnecessary phy.h include

[Russell King - ARM Linux]

Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel.  There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.

Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.

This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.

In order to make this change, several drivers need to be updated to
include necessary headers that they were picking up through this
include.  This has resulted in a much larger patch series.

I'm assuming the 0-day builder has had 24 hours with this series, and
hasn't reported any further issues with it - the last issue was two
weeks ago (before I became ill) which I fixed over the last weekend.

I'm hoping this doesn't conflict with what's already in net-next...

 arch/mips/cavium-octeon/octeon-platform.c             | 4 ----
 drivers/net/dsa/mv88e6xxx/mv88e6xxx.h                 | 1 +
 drivers/net/ethernet/broadcom/bgmac.c                 | 2 ++
 drivers/net/ethernet/cadence/macb.h                   | 2 ++
 drivers/net/ethernet/cavium/liquidio/lio_main.c       | 1 +
 drivers/net/ethernet/cavium/liquidio/lio_vf_main.c    | 1 +
 drivers/net/ethernet/cavium/liquidio/octeon_console.c | 1 +
 drivers/net/ethernet/freescale/fman/fman_memac.c      | 1 +
 drivers/net/ethernet/marvell/mvneta.c                 | 1 +
 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c       | 1 +
 drivers/net/usb/lan78xx.c                             | 1 +
 drivers/net/wireless/ath/ath5k/ahb.c                  | 2 +-
 drivers/target/iscsi/iscsi_target_login.c             | 1 +
 include/net/dsa.h                                     | 6 ++++--
 net/core/netprio_cgroup.c                             | 1 +
 net/sunrpc/xprtrdma/svc_rdma_backchannel.c            | 1 +
 16 files changed, 20 insertions(+), 7 deletions(-)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH 4.10-rc3 00/13] net: dsa: remove unnecessary phy.h include

[Russell King - ARM Linux]

Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel.  There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.

Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.

This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.

In order to make this change, several drivers need to be updated to
include necessary headers that they were picking up through this
include.  This has resulted in a much larger patch series.

I'm assuming the 0-day builder has had 24 hours with this series, and
hasn't reported any further issues with it - the last issue was two
weeks ago (before I became ill) which I fixed over the last weekend.

I'm hoping this doesn't conflict with what's already in net-next...

 arch/mips/cavium-octeon/octeon-platform.c             | 4 ----
 drivers/net/dsa/mv88e6xxx/mv88e6xxx.h                 | 1 +
 drivers/net/ethernet/broadcom/bgmac.c                 | 2 ++
 drivers/net/ethernet/cadence/macb.h                   | 2 ++
 drivers/net/ethernet/cavium/liquidio/lio_main.c       | 1 +
 drivers/net/ethernet/cavium/liquidio/lio_vf_main.c    | 1 +
 drivers/net/ethernet/cavium/liquidio/octeon_console.c | 1 +
 drivers/net/ethernet/freescale/fman/fman_memac.c      | 1 +
 drivers/net/ethernet/marvell/mvneta.c                 | 1 +
 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c       | 1 +
 drivers/net/usb/lan78xx.c                             | 1 +
 drivers/net/wireless/ath/ath5k/ahb.c                  | 2 +-
 drivers/target/iscsi/iscsi_target_login.c             | 1 +
 include/net/dsa.h                                     | 6 ++++--
 net/core/netprio_cgroup.c                             | 1 +
 net/sunrpc/xprtrdma/svc_rdma_backchannel.c            | 1 +
 16 files changed, 20 insertions(+), 7 deletions(-)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH 4.10-rc3 00/13] net: dsa: remove unnecessary phy.h include

[Russell King - ARM Linux]

Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel.  There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.

Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.

This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.

In order to make this change, several drivers need to be updated to
include necessary headers that they were picking up through this
include.  This has resulted in a much larger patch series.

I'm assuming the 0-day builder has had 24 hours with this series, and
hasn't reported any further issues with it - the last issue was two
weeks ago (before I became ill) which I fixed over the last weekend.

I'm hoping this doesn't conflict with what's already in net-next...

 arch/mips/cavium-octeon/octeon-platform.c             | 4 ----
 drivers/net/dsa/mv88e6xxx/mv88e6xxx.h                 | 1 +
 drivers/net/ethernet/broadcom/bgmac.c                 | 2 ++
 drivers/net/ethernet/cadence/macb.h                   | 2 ++
 drivers/net/ethernet/cavium/liquidio/lio_main.c       | 1 +
 drivers/net/ethernet/cavium/liquidio/lio_vf_main.c    | 1 +
 drivers/net/ethernet/cavium/liquidio/octeon_console.c | 1 +
 drivers/net/ethernet/freescale/fman/fman_memac.c      | 1 +
 drivers/net/ethernet/marvell/mvneta.c                 | 1 +
 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c       | 1 +
 drivers/net/usb/lan78xx.c                             | 1 +
 drivers/net/wireless/ath/ath5k/ahb.c                  | 2 +-
 drivers/target/iscsi/iscsi_target_login.c             | 1 +
 include/net/dsa.h                                     | 6 ++++--
 net/core/netprio_cgroup.c                             | 1 +
 net/sunrpc/xprtrdma/svc_rdma_backchannel.c            | 1 +
 16 files changed, 20 insertions(+), 7 deletions(-)

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.

[PATCH 4.10-rc3 01/13] net: sunrpc: fix build errors when linux/phy*.h is removed from net/dsa.h

[Russell King]

Removing linux/phy.h from net/dsa.h reveals a build error in the sunrpc
code:

net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_rdma_bc_put':
net/sunrpc/xprtrdma/svc_rdma_backchannel.c:277:2: error: implicit declaration of function 'module_put' [-Werror=implicit-function-declaration]
net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_setup_rdma_bc':
net/sunrpc/xprtrdma/svc_rdma_backchannel.c:348:7: error: implicit declaration of function 'try_module_get' [-Werror=implicit-function-declaration]

Fix this by adding linux/module.h to svc_rdma_backchannel.c

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 net/sunrpc/xprtrdma/svc_rdma_backchannel.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
index 288e35c2d8f4..cb1e48e54eb1 100644
--- a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
+++ b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
@@ -4,6 +4,7 @@
  * Support for backward direction RPCs on RPC/RDMA (server-side).
  */
 
+#include <linux/module.h>
 #include <linux/sunrpc/svc_rdma.h>
 #include "xprt_rdma.h"
 
-- 
2.7.4

Re: [PATCH 4.10-rc3 01/13] net: sunrpc: fix build errors when linux/phy*.h is removed from net/dsa.h

[Anna Schumaker]

Hi Russell,

On 01/31/2017 02:18 PM, Russell King wrote:
> Removing linux/phy.h from net/dsa.h reveals a build error in the sunrpc
> code:
> 
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_rdma_bc_put':
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c:277:2: error: implicit declaration of function 'module_put' [-Werror=implicit-function-declaration]
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_setup_rdma_bc':
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c:348:7: error: implicit declaration of function 'try_module_get' [-Werror=implicit-function-declaration]
> 
> Fix this by adding linux/module.h to svc_rdma_backchannel.c
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

This patch looks okay to me:

Acked-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

> ---
>  net/sunrpc/xprtrdma/svc_rdma_backchannel.c | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> index 288e35c2d8f4..cb1e48e54eb1 100644
> --- a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> +++ b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> @@ -4,6 +4,7 @@
>   * Support for backward direction RPCs on RPC/RDMA (server-side).
>   */
>  
> +#include <linux/module.h>
>  #include <linux/sunrpc/svc_rdma.h>
>  #include "xprt_rdma.h"
>  
> 

Re: [PATCH 4.10-rc3 01/13] net: sunrpc: fix build errors when linux/phy*.h is removed from net/dsa.h

[Anna Schumaker]

Hi Russell,

On 01/31/2017 02:18 PM, Russell King wrote:
> Removing linux/phy.h from net/dsa.h reveals a build error in the sunrpc
> code:
> 
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_rdma_bc_put':
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c:277:2: error: implicit declaration of function 'module_put' [-Werror=implicit-function-declaration]
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_setup_rdma_bc':
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c:348:7: error: implicit declaration of function 'try_module_get' [-Werror=implicit-function-declaration]
> 
> Fix this by adding linux/module.h to svc_rdma_backchannel.c
> 
> Signed-off-by: Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org>

This patch looks okay to me:

Acked-by: Anna Schumaker <Anna.Schumaker-ZwjVKphTwtPQT0dZR+AlfA@public.gmane.org>

> ---
>  net/sunrpc/xprtrdma/svc_rdma_backchannel.c | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> index 288e35c2d8f4..cb1e48e54eb1 100644
> --- a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> +++ b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> @@ -4,6 +4,7 @@
>   * Support for backward direction RPCs on RPC/RDMA (server-side).
>   */
>  
> +#include <linux/module.h>
>  #include <linux/sunrpc/svc_rdma.h>
>  #include "xprt_rdma.h"
>  
> 

Re: [PATCH 4.10-rc3 01/13] net: sunrpc: fix build errors when linux/phy*.h is removed from net/dsa.h

[Anna Schumaker]

Hi Russell,

On 01/31/2017 02:18 PM, Russell King wrote:
> Removing linux/phy.h from net/dsa.h reveals a build error in the sunrpc
> code:
> 
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_rdma_bc_put':
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c:277:2: error: implicit declaration of function 'module_put' [-Werror=implicit-function-declaration]
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_setup_rdma_bc':
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c:348:7: error: implicit declaration of function 'try_module_get' [-Werror=implicit-function-declaration]
> 
> Fix this by adding linux/module.h to svc_rdma_backchannel.c
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

This patch looks okay to me:

Acked-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

> ---
>  net/sunrpc/xprtrdma/svc_rdma_backchannel.c | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> index 288e35c2d8f4..cb1e48e54eb1 100644
> --- a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> +++ b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> @@ -4,6 +4,7 @@
>   * Support for backward direction RPCs on RPC/RDMA (server-side).
>   */
>  
> +#include <linux/module.h>
>  #include <linux/sunrpc/svc_rdma.h>
>  #include "xprt_rdma.h"
>  
> 

Re: [PATCH 4.10-rc3 01/13] net: sunrpc: fix build errors when linux/phy*.h is removed from net/dsa.h

[Anna Schumaker]

Hi Russell,

On 01/31/2017 02:18 PM, Russell King wrote:
> Removing linux/phy.h from net/dsa.h reveals a build error in the sunrpc
> code:
> 
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_rdma_bc_put':
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c:277:2: error: implicit declaration of function 'module_put' [-Werror=implicit-function-declaration]
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_setup_rdma_bc':
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c:348:7: error: implicit declaration of function 'try_module_get' [-Werror=implicit-function-declaration]
> 
> Fix this by adding linux/module.h to svc_rdma_backchannel.c
> 
> Signed-off-by: Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org>

This patch looks okay to me:

Acked-by: Anna Schumaker <Anna.Schumaker-ZwjVKphTwtPQT0dZR+AlfA@public.gmane.org>

> ---
>  net/sunrpc/xprtrdma/svc_rdma_backchannel.c | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> index 288e35c2d8f4..cb1e48e54eb1 100644
> --- a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> +++ b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> @@ -4,6 +4,7 @@
>   * Support for backward direction RPCs on RPC/RDMA (server-side).
>   */
>  
> +#include <linux/module.h>
>  #include <linux/sunrpc/svc_rdma.h>
>  #include "xprt_rdma.h"
>  
> 

[PATCH 4.10-rc3 02/13] net: cgroups: fix build errors when linux/phy*.h is removed from net/dsa.h

[Russell King]

net/core/netprio_cgroup.c:303:16: error: expected declaration specifiers or '...' before string constant
    MODULE_LICENSE("GPL v2");
                   ^~~~~~~~

Add linux/module.h to fix this.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 net/core/netprio_cgroup.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/core/netprio_cgroup.c b/net/core/netprio_cgroup.c
index 2ec86fc552df..756637dc7a57 100644
--- a/net/core/netprio_cgroup.c
+++ b/net/core/netprio_cgroup.c
@@ -13,6 +13,7 @@
 
 #include <linux/slab.h>
 #include <linux/types.h>
+#include <linux/module.h>
 #include <linux/string.h>
 #include <linux/errno.h>
 #include <linux/skbuff.h>
-- 
2.7.4

[PATCH 4.10-rc3 03/13] net: macb: fix build errors when linux/phy*.h is removed from net/dsa.h

[Russell King]

drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
     phy_interface_t  phy_interface;
     ^~~~~~~~~~~~~~~

Add linux/phy.h to macb.h

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/net/ethernet/cadence/macb.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index d67adad67be1..383da8cf5f6d 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h
@@ -10,6 +10,8 @@
 #ifndef _MACB_H
 #define _MACB_H
 
+#include <linux/phy.h>
+
 #define MACB_GREGS_NBR 16
 #define MACB_GREGS_VERSION 2
 #define MACB_MAX_QUEUES 8
-- 
2.7.4

Re: [PATCH 4.10-rc3 03/13] net: macb: fix build errors when linux/phy*.h is removed from net/dsa.h

[Nicolas Ferre]

Le 31/01/2017 à 20:18, Russell King a écrit :
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
> drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
> drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
> In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
> drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
>      phy_interface_t  phy_interface;
>      ^~~~~~~~~~~~~~~
> 
> Add linux/phy.h to macb.h
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

> ---
>  drivers/net/ethernet/cadence/macb.h | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
> index d67adad67be1..383da8cf5f6d 100644
> --- a/drivers/net/ethernet/cadence/macb.h
> +++ b/drivers/net/ethernet/cadence/macb.h
> @@ -10,6 +10,8 @@
>  #ifndef _MACB_H
>  #define _MACB_H
>  
> +#include <linux/phy.h>
> +
>  #define MACB_GREGS_NBR 16
>  #define MACB_GREGS_VERSION 2
>  #define MACB_MAX_QUEUES 8
> 


-- 
Nicolas Ferre

Re: [PATCH 4.10-rc3 03/13] net: macb: fix build errors when linux/phy*.h is removed from net/dsa.h

[Nicolas Ferre]

Le 31/01/2017 à 20:18, Russell King a écrit :
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
> drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
> drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
> In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
> drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
>      phy_interface_t  phy_interface;
>      ^~~~~~~~~~~~~~~
> 
> Add linux/phy.h to macb.h
> 
> Signed-off-by: Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org>

Acked-by: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>

> ---
>  drivers/net/ethernet/cadence/macb.h | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
> index d67adad67be1..383da8cf5f6d 100644
> --- a/drivers/net/ethernet/cadence/macb.h
> +++ b/drivers/net/ethernet/cadence/macb.h
> @@ -10,6 +10,8 @@
>  #ifndef _MACB_H
>  #define _MACB_H
>  
> +#include <linux/phy.h>
> +
>  #define MACB_GREGS_NBR 16
>  #define MACB_GREGS_VERSION 2
>  #define MACB_MAX_QUEUES 8
> 


-- 
Nicolas Ferre
--
To unsubscribe from this list: send the line "unsubscribe linux-nfs" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 4.10-rc3 03/13] net: macb: fix build errors when linux/phy*.h is removed from net/dsa.h

[Nicolas Ferre]

Le 31/01/2017 à 20:18, Russell King a écrit :
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
> drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
> drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
> In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
> drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
>      phy_interface_t  phy_interface;
>      ^~~~~~~~~~~~~~~
> 
> Add linux/phy.h to macb.h
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

> ---
>  drivers/net/ethernet/cadence/macb.h | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
> index d67adad67be1..383da8cf5f6d 100644
> --- a/drivers/net/ethernet/cadence/macb.h
> +++ b/drivers/net/ethernet/cadence/macb.h
> @@ -10,6 +10,8 @@
>  #ifndef _MACB_H
>  #define _MACB_H
>  
> +#include <linux/phy.h>
> +
>  #define MACB_GREGS_NBR 16
>  #define MACB_GREGS_VERSION 2
>  #define MACB_MAX_QUEUES 8
> 


-- 
Nicolas Ferre

Re: [PATCH 4.10-rc3 03/13] net: macb: fix build errors when linux/phy*.h is removed from net/dsa.h

[Nicolas Ferre]

Le 31/01/2017 à 20:18, Russell King a écrit :
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
> drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
> drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
> drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
> In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
> drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
>      phy_interface_t  phy_interface;
>      ^~~~~~~~~~~~~~~
> 
> Add linux/phy.h to macb.h
> 
> Signed-off-by: Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org>

Acked-by: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>

> ---
>  drivers/net/ethernet/cadence/macb.h | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
> index d67adad67be1..383da8cf5f6d 100644
> --- a/drivers/net/ethernet/cadence/macb.h
> +++ b/drivers/net/ethernet/cadence/macb.h
> @@ -10,6 +10,8 @@
>  #ifndef _MACB_H
>  #define _MACB_H
>  
> +#include <linux/phy.h>
> +
>  #define MACB_GREGS_NBR 16
>  #define MACB_GREGS_VERSION 2
>  #define MACB_MAX_QUEUES 8
> 


-- 
Nicolas Ferre
--
To unsubscribe from this list: send the line "unsubscribe linux-nfs" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 4.10-rc3 04/13] net: lan78xx: fix build errors when linux/phy*.h is removed from net/dsa.h

[Russell King]

drivers/net/usb/lan78xx.c:394:33: sparse: expected ; at end of declaration
drivers/net/usb/lan78xx.c:394:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/usb/lan78xx.c:394:33: sparse: got interface
drivers/net/usb/lan78xx.c:403:1: sparse: Expected ; at the end of type declaration
drivers/net/usb/lan78xx.c:403:1: sparse: got }

Add linux/phy.h to lan78xx.c

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/net/usb/lan78xx.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c
index 08f8703e4d54..9889a70ff4f6 100644
--- a/drivers/net/usb/lan78xx.c
+++ b/drivers/net/usb/lan78xx.c
@@ -35,6 +35,7 @@
 #include <linux/irq.h>
 #include <linux/irqchip/chained_irq.h>
 #include <linux/microchipphy.h>
+#include <linux/phy.h>
 #include "lan78xx.h"
 
 #define DRIVER_AUTHOR	"WOOJUNG HUH <woojung.huh@microchip.com>"
-- 
2.7.4

[PATCH 4.10-rc3 05/13] net: bgmac: fix build errors when linux/phy*.h is removed from net/dsa.h

[Russell King]

drivers/net/ethernet/broadcom/bgmac.c:1015:17: error: dereferencing pointer to incomplete type 'struct mii_bus'
drivers/net/ethernet/broadcom/bgmac.c:1185:2: error: implicit declaration of function 'phy_start' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1198:2: error: implicit declaration of function 'phy_stop' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1239:9: error: implicit declaration of function 'phy_mii_ioctl' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1389:28: error: 'phy_ethtool_get_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1390:28: error: 'phy_ethtool_set_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1403:13: error: dereferencing pointer to incomplete type 'struct phy_device'
drivers/net/ethernet/broadcom/bgmac.c:1417:3: error: implicit declaration of function 'phy_print_status' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1424:26: error: storage size of 'fphy_status' isn't known
drivers/net/ethernet/broadcom/bgmac.c:1424:9: error: variable 'fphy_status' has initializer but incomplete type
drivers/net/ethernet/broadcom/bgmac.c:1425:11: warning: excess elements in struct initializer
drivers/net/ethernet/broadcom/bgmac.c:1425:3: error: unknown field 'link' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1426:12: note: in expansion of macro 'SPEED_1000'
drivers/net/ethernet/broadcom/bgmac.c:1426:3: error: unknown field 'speed' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1427:13: note: in expansion of macro 'DUPLEX_FULL'
drivers/net/ethernet/broadcom/bgmac.c:1427:3: error: unknown field 'duplex' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1432:12: error: implicit declaration of function 'fixed_phy_register' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1432:31: error: 'PHY_POLL' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1438:8: error: implicit declaration of function 'phy_connect_direct' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1439:6: error: 'PHY_INTERFACE_MODE_MII' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1521:2: error: implicit declaration of function 'phy_disconnect' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1541:15: error: expected declaration specifiers or '...' before string constant

Add linux/phy.h to bgmac.c

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/net/ethernet/broadcom/bgmac.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
index 0e066dc6b8cc..58a2bd3c0458 100644
--- a/drivers/net/ethernet/broadcom/bgmac.c
+++ b/drivers/net/ethernet/broadcom/bgmac.c
@@ -12,6 +12,8 @@
 #include <linux/bcma/bcma.h>
 #include <linux/etherdevice.h>
 #include <linux/bcm47xx_nvram.h>
+#include <linux/phy.h>
+#include <linux/phy_fixed.h>
 #include "bgmac.h"
 
 static bool bgmac_wait_value(struct bgmac *bgmac, u16 reg, u32 mask,
-- 
2.7.4

Re: [PATCH 4.10-rc3 05/13] net: bgmac: fix build errors when linux/phy*.h is removed from net/dsa.h

[Rafał Miłecki]

On 01/31/2017 08:18 PM, Russell King wrote:
> drivers/net/ethernet/broadcom/bgmac.c:1015:17: error: dereferencing pointer to incomplete type 'struct mii_bus'
> drivers/net/ethernet/broadcom/bgmac.c:1185:2: error: implicit declaration of function 'phy_start' [-Werror=implicit-function-declaration]
> drivers/net/ethernet/broadcom/bgmac.c:1198:2: error: implicit declaration of function 'phy_stop' [-Werror=implicit-function-declaration]
> drivers/net/ethernet/broadcom/bgmac.c:1239:9: error: implicit declaration of function 'phy_mii_ioctl' [-Werror=implicit-function-declaration]
> drivers/net/ethernet/broadcom/bgmac.c:1389:28: error: 'phy_ethtool_get_link_ksettings' undeclared here (not in a function)
> drivers/net/ethernet/broadcom/bgmac.c:1390:28: error: 'phy_ethtool_set_link_ksettings' undeclared here (not in a function)
> drivers/net/ethernet/broadcom/bgmac.c:1403:13: error: dereferencing pointer to incomplete type 'struct phy_device'
> drivers/net/ethernet/broadcom/bgmac.c:1417:3: error: implicit declaration of function 'phy_print_status' [-Werror=implicit-function-declaration]
> drivers/net/ethernet/broadcom/bgmac.c:1424:26: error: storage size of 'fphy_status' isn't known
> drivers/net/ethernet/broadcom/bgmac.c:1424:9: error: variable 'fphy_status' has initializer but incomplete type
> drivers/net/ethernet/broadcom/bgmac.c:1425:11: warning: excess elements in struct initializer
> drivers/net/ethernet/broadcom/bgmac.c:1425:3: error: unknown field 'link' specified in initializer
> drivers/net/ethernet/broadcom/bgmac.c:1426:12: note: in expansion of macro 'SPEED_1000'
> drivers/net/ethernet/broadcom/bgmac.c:1426:3: error: unknown field 'speed' specified in initializer
> drivers/net/ethernet/broadcom/bgmac.c:1427:13: note: in expansion of macro 'DUPLEX_FULL'
> drivers/net/ethernet/broadcom/bgmac.c:1427:3: error: unknown field 'duplex' specified in initializer
> drivers/net/ethernet/broadcom/bgmac.c:1432:12: error: implicit declaration of function 'fixed_phy_register' [-Werror=implicit-function-declaration]
> drivers/net/ethernet/broadcom/bgmac.c:1432:31: error: 'PHY_POLL' undeclared (first use in this function)
> drivers/net/ethernet/broadcom/bgmac.c:1438:8: error: implicit declaration of function 'phy_connect_direct' [-Werror=implicit-function-declaration]
> drivers/net/ethernet/broadcom/bgmac.c:1439:6: error: 'PHY_INTERFACE_MODE_MII' undeclared (first use in this function)
> drivers/net/ethernet/broadcom/bgmac.c:1521:2: error: implicit declaration of function 'phy_disconnect' [-Werror=implicit-function-declaration]
> drivers/net/ethernet/broadcom/bgmac.c:1541:15: error: expected declaration specifiers or '...' before string constant
>
> Add linux/phy.h to bgmac.c
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Acked-by: Rafał Miłecki <rafal@milecki.pl>

[PATCH 4.10-rc3 06/13] net: fman: fix build errors when linux/phy*.h is removed from net/dsa.h

[Russell King]

drivers/net/ethernet/freescale/fman/fman_memac.c:519:21: error: dereferencing pointer to incomplete type 'struct fixed_phy_status'

Add linux/phy_fixed.h to fman_memac.c

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/net/ethernet/freescale/fman/fman_memac.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/freescale/fman/fman_memac.c b/drivers/net/ethernet/freescale/fman/fman_memac.c
index 71a5ded9d1de..cd6a53eaf161 100644
--- a/drivers/net/ethernet/freescale/fman/fman_memac.c
+++ b/drivers/net/ethernet/freescale/fman/fman_memac.c
@@ -38,6 +38,7 @@
 #include <linux/slab.h>
 #include <linux/io.h>
 #include <linux/phy.h>
+#include <linux/phy_fixed.h>
 #include <linux/of_mdio.h>
 
 /* PCS registers */
-- 
2.7.4

[PATCH 4.10-rc3 07/13] net: mvneta: fix build errors when linux/phy*.h is removed from net/dsa.h

[Russell King]

drivers/net/ethernet/marvell/mvneta.c:2694:26: error: storage size of 'status' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:26: error: storage size of 'changed' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:9: error: variable 'changed' has initializer but incomplete type
drivers/net/ethernet/marvell/mvneta.c:2709:2: error: implicit declaration of function 'fixed_phy_update_state' [-Werror=implicit-function-declaration]

Add linux/phy_fixed.h to mvneta.c

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/net/ethernet/marvell/mvneta.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index e05e22705cf7..eb0eb3e62ca0 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -28,6 +28,7 @@
 #include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include <linux/phy.h>
+#include <linux/phy_fixed.h>
 #include <linux/platform_device.h>
 #include <linux/skbuff.h>
 #include <net/hwbm.h>
-- 
2.7.4

Re: [PATCH 4.10-rc3 07/13] net: mvneta: fix build errors when linux/phy*.h is removed from net/dsa.h

[Thomas Petazzoni]

Hello,

On Tue, 31 Jan 2017 19:18:59 +0000, Russell King wrote:
> drivers/net/ethernet/marvell/mvneta.c:2694:26: error: storage size of 'status' isn't known
> drivers/net/ethernet/marvell/mvneta.c:2695:26: error: storage size of 'changed' isn't known
> drivers/net/ethernet/marvell/mvneta.c:2695:9: error: variable 'changed' has initializer but incomplete type
> drivers/net/ethernet/marvell/mvneta.c:2709:2: error: implicit declaration of function 'fixed_phy_update_state' [-Werror=implicit-function-declaration]
> 
> Add linux/phy_fixed.h to mvneta.c
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Re: [PATCH 4.10-rc3 07/13] net: mvneta: fix build errors when linux/phy*.h is removed from net/dsa.h

[Thomas Petazzoni]

Hello,

On Tue, 31 Jan 2017 19:18:59 +0000, Russell King wrote:
> drivers/net/ethernet/marvell/mvneta.c:2694:26: error: storage size of 'status' isn't known
> drivers/net/ethernet/marvell/mvneta.c:2695:26: error: storage size of 'changed' isn't known
> drivers/net/ethernet/marvell/mvneta.c:2695:9: error: variable 'changed' has initializer but incomplete type
> drivers/net/ethernet/marvell/mvneta.c:2709:2: error: implicit declaration of function 'fixed_phy_update_state' [-Werror=implicit-function-declaration]
> 
> Add linux/phy_fixed.h to mvneta.c
> 
> Signed-off-by: Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org>

Acked-by: Thomas Petazzoni <thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
-- 
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe linux-nfs" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 4.10-rc3 08/13] net: emac: fix build errors when linux/phy*.h is removed from net/dsa.h

[Russell King]

drivers/net/ethernet/qualcomm/emac/emac-sgmii.c:58:12: error: dereferencing pointer to incomplete type 'struct phy_device'

Add linux/phy.h to emac-sgmii.c

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
index bf722a9bb09d..5e31fb7e4ab8 100644
--- a/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
+++ b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
@@ -16,6 +16,7 @@
 #include <linux/iopoll.h>
 #include <linux/acpi.h>
 #include <linux/of_device.h>
+#include <linux/phy.h>
 #include "emac.h"
 #include "emac-mac.h"
 #include "emac-sgmii.h"
-- 
2.7.4

Re: [PATCH 4.10-rc3 08/13] net: emac: fix build errors when linux/phy*.h is removed from net/dsa.h

[Timur Tabi]

On 01/31/2017 01:19 PM, Russell King wrote:
> drivers/net/ethernet/qualcomm/emac/emac-sgmii.c:58:12: error: dereferencing pointer to incomplete type 'struct phy_device'
>
> Add linux/phy.h to emac-sgmii.c
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>  drivers/net/ethernet/qualcomm/emac/emac-sgmii.c | 1 +

The version of emac-sgmii.c on net-next does not need this fixed.  I already 
removed all references to phy_device in commit "net: qcom/emac: always use 
autonegotiation to configure the SGMII link".

-- 
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc.  Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.

Re: [PATCH 4.10-rc3 08/13] net: emac: fix build errors when linux/phy*.h is removed from net/dsa.h

[Timur Tabi]

On 01/31/2017 01:19 PM, Russell King wrote:
> drivers/net/ethernet/qualcomm/emac/emac-sgmii.c:58:12: error: dereferencing pointer to incomplete type 'struct phy_device'
>
> Add linux/phy.h to emac-sgmii.c
>
> Signed-off-by: Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org>
> ---
>  drivers/net/ethernet/qualcomm/emac/emac-sgmii.c | 1 +

The version of emac-sgmii.c on net-next does not need this fixed.  I already 
removed all references to phy_device in commit "net: qcom/emac: always use 
autonegotiation to configure the SGMII link".

-- 
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm
Technologies, Inc.  Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 4.10-rc3 09/13] iscsi: fix build errors when linux/phy*.h is removed from net/dsa.h

[Russell King]

drivers/target/iscsi/iscsi_target_login.c:1135:7: error: implicit declaration of function 'try_module_get' [-Werror=implicit-function-declaration]

Add linux/module.h to iscsi_target_login.c.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/target/iscsi/iscsi_target_login.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/target/iscsi/iscsi_target_login.c b/drivers/target/iscsi/iscsi_target_login.c
index 450f51deb2a2..eab274d17b5c 100644
--- a/drivers/target/iscsi/iscsi_target_login.c
+++ b/drivers/target/iscsi/iscsi_target_login.c
@@ -17,6 +17,7 @@
  ******************************************************************************/
 
 #include <crypto/hash.h>
+#include <linux/module.h>
 #include <linux/string.h>
 #include <linux/kthread.h>
 #include <linux/idr.h>
-- 
2.7.4

Re: [PATCH 4.10-rc3 09/13] iscsi: fix build errors when linux/phy*.h is removed from net/dsa.h

[Bart Van Assche]

On Tue, 2017-01-31 at 19:19 +0000, Russell King wrote:
> drivers/target/iscsi/iscsi_target_login.c:1135:7: error: implicit declara=
tion of function 'try_module_get' [-Werror=3Dimplicit-function-declaration]
>=20
> Add linux/module.h to iscsi_target_login.c.
>=20
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>  drivers/target/iscsi/iscsi_target_login.c | 1 +
>  1 file changed, 1 insertion(+)
>=20
> diff --git a/drivers/target/iscsi/iscsi_target_login.c b/drivers/target/i=
scsi/iscsi_target_login.c
> index 450f51deb2a2..eab274d17b5c 100644
> --- a/drivers/target/iscsi/iscsi_target_login.c
> +++ b/drivers/target/iscsi/iscsi_target_login.c
> @@ -17,6 +17,7 @@
>   ***********************************************************************=
*******/
> =20
>  #include <crypto/hash.h>
> +#include <linux/module.h>
>  #include <linux/string.h>
>  #include <linux/kthread.h>
>  #include <linux/idr.h>

Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>=

Re: [PATCH 4.10-rc3 09/13] iscsi: fix build errors when linux/phy*.h is removed from net/dsa.h

[Bart Van Assche]

On Tue, 2017-01-31 at 19:19 +0000, Russell King wrote:
> drivers/target/iscsi/iscsi_target_login.c:1135:7: error: implicit declaration of function 'try_module_get' [-Werror=implicit-function-declaration]
> 
> Add linux/module.h to iscsi_target_login.c.
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>  drivers/target/iscsi/iscsi_target_login.c | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/drivers/target/iscsi/iscsi_target_login.c b/drivers/target/iscsi/iscsi_target_login.c
> index 450f51deb2a2..eab274d17b5c 100644
> --- a/drivers/target/iscsi/iscsi_target_login.c
> +++ b/drivers/target/iscsi/iscsi_target_login.c
> @@ -17,6 +17,7 @@
>   ******************************************************************************/
>  
>  #include <crypto/hash.h>
> +#include <linux/module.h>
>  #include <linux/string.h>
>  #include <linux/kthread.h>
>  #include <linux/idr.h>

Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>

Re: [PATCH 4.10-rc3 09/13] iscsi: fix build errors when linux/phy*.h is removed from net/dsa.h

[Bart Van Assche]

On Tue, 2017-01-31 at 19:19 +0000, Russell King wrote:
> drivers/target/iscsi/iscsi_target_login.c:1135:7: error: implicit declaration of function 'try_module_get' [-Werror=implicit-function-declaration]
> 
> Add linux/module.h to iscsi_target_login.c.
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
>  drivers/target/iscsi/iscsi_target_login.c | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/drivers/target/iscsi/iscsi_target_login.c b/drivers/target/iscsi/iscsi_target_login.c
> index 450f51deb2a2..eab274d17b5c 100644
> --- a/drivers/target/iscsi/iscsi_target_login.c
> +++ b/drivers/target/iscsi/iscsi_target_login.c
> @@ -17,6 +17,7 @@
>   ******************************************************************************/
>  
>  #include <crypto/hash.h>
> +#include <linux/module.h>
>  #include <linux/string.h>
>  #include <linux/kthread.h>
>  #include <linux/idr.h>

Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
From Anna.Schumaker@netapp.com Tue Jan 31 20:49:19 2017
Received: with ECARTIS (v1.0.0; list linux-mips); Tue, 31 Jan 2017 20:49:27 +0100 (CET)
Received: from mx144.netapp.com ([216.240.21.25]:30617 "EHLO mx144.netapp.com"
        rhost-flags-OK-OK-OK-OK) by eddie.linux-mips.org with ESMTP
        id S23993899AbdAaTtTu5Hxi (ORCPT <rfc822;linux-mips@linux-mips.org>);
        Tue, 31 Jan 2017 20:49:19 +0100
X-IronPort-AV: E=Sophos;i="5.33,315,1477983600"; 
   d="scan'208";a="174051109"
Received: from vmwexchts01-prd.hq.netapp.com ([10.122.105.12])
  by mx144-out.netapp.com with ESMTP; 31 Jan 2017 11:40:54 -0800
Received: from VMWEXCCAS03-PRD.hq.netapp.com (10.122.105.19) by
 VMWEXCHTS01-PRD.hq.netapp.com (10.122.105.12) with Microsoft SMTP Server
 (TLS) id 15.0.1210.3; Tue, 31 Jan 2017 11:48:12 -0800
Received: from NAM02-CY1-obe.outbound.protection.outlook.com (10.120.60.153)
 by VMWEXCCAS03-PRD.hq.netapp.com (10.122.105.19) with Microsoft SMTP Server
 (TLS) id 15.0.1210.3 via Frontend Transport; Tue, 31 Jan 2017 11:48:12 -0800
DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed;
 d=netapp.onmicrosoft.com; s=selector1-netapp-com;
 h=From:Date:Subject:Message-ID:Content-Type:MIME-Version;
 bh=uOWCiHoJOkeJ03T4mq0DkYm1YX/LM+dO6vMB4b4yogo=;
 b=ol0wo4fSJiK9ThT5aRZzpKEfdIMlk3oOq2hVjsGGH5cB8RvD0evUS3Rd+bd6P79YOdedQzTjOZbnvMA6Vkp1Cuz32mD4CUgmpIldMDVS9cbU1T3iav5x4hBPocr9jbxDnHDHYgCAkphs+kXVAQ723EPvkCqNQHvhqCzrKJJQUKQ=
Authentication-Results: spf=none (sender IP is )
 smtp.mailfrom=Anna.Schumaker@netapp.com; 
Received: from gouda.nowheycreamery.com (68.40.188.1) by
 BLUPR0601MB1635.namprd06.prod.outlook.com (10.163.212.141) with Microsoft
 SMTP Server (version=TLS1_2,
 cipher=TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA384_P384) id 15.1.874.12; Tue, 31
 Jan 2017 19:48:07 +0000
Subject: Re: [PATCH 4.10-rc3 01/13] net: sunrpc: fix build errors when
 linux/phy*.h is removed from net/dsa.h
To:     Russell King <rmk+kernel@armlinux.org.uk>,
        <linux-mips@linux-mips.org>, <linux-nfs@vger.kernel.org>,
        <linux-scsi@vger.kernel.org>, <linux-usb@vger.kernel.org>,
        <linux-wireless@vger.kernel.org>, <netdev@vger.kernel.org>,
        <target-devel@vger.kernel.org>
References: <20170131191704.GA8281@n2100.armlinux.org.uk>
 <E1cYdwi-0000Vs-97@rmk-PC.armlinux.org.uk>
CC:     "David S. Miller" <davem@davemloft.net>,
        Florian Fainelli <f.fainelli@gmail.com>,
        "J. Bruce Fields" <bfields@fieldses.org>,
        Jeff Layton <jlayton@poochiereds.net>,
        Trond Myklebust <trond.myklebust@primarydata.com>
From:   Anna Schumaker <Anna.Schumaker@Netapp.com>
Message-ID: <52ceb082-1e0a-7210-833a-f4ac22df4b8c@Netapp.com>
Date:   Tue, 31 Jan 2017 14:48:02 -0500
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:45.0) Gecko/20100101
 Thunderbird/45.6.0
MIME-Version: 1.0
In-Reply-To: <E1cYdwi-0000Vs-97@rmk-PC.armlinux.org.uk>
Content-Type: text/plain; charset="utf-8"
Content-Transfer-Encoding: 7bit
X-Originating-IP: [68.40.188.1]
X-ClientProxiedBy: MWHPR14CA0052.namprd14.prod.outlook.com (10.173.97.142) To
 BLUPR0601MB1635.namprd06.prod.outlook.com (10.163.212.141)
X-MS-Office365-Filtering-Correlation-Id: 0b097ef3-bc3b-4f54-2fb0-08d44a12156a
X-Microsoft-Antispam: UriScan:;BCL:0;PCL:0;RULEID:(22001);SRVR:BLUPR0601MB1635;
X-Microsoft-Exchange-Diagnostics: 1;BLUPR0601MB1635;3:pqQdKQnggVpXZO9kxDGGHXk3jnYxph8zNcHgN123tPYZ6V21FkmUKK0KLfpFZbd+MDx48Y0ZQpEnYayQEqbYLIkxb7/pSsJp3oY5Bhd+WbIJ0q3evXFvZdFo3FjGg4WAq5/JqKpcF7V0bqktVaq//9kN78GINRzSysWksyulT3TfakRpmVsM36PjLeZSP/4cLUUi5Kzzn1skeyeYJWvtzZp73Nx/AOAljKKRPlEiRUDnt1dHDecckXOis6u0phWDVu08AwmgkFAdIiINYOrkZw==;25:H7evsomXQrGUJrzkwAjsHBn39ESJypT6h+oQ+JNNzHEslcZvDqHRnC2tk9i4xWdrrvNG9wh4wcGOHqNqCnHeP6e9gYLkkjj9bTIbJAUmcpcL09H1OH7UdlAdr6wrUdcgT7dSyk5LMslrROICSbXM4dDjzhX1+yPj8s9lB0B3jvFNH0l5bWGFlpnl3NrBNHq19gOTlqnWTSHtQ4apE15BGNQEFZNDWMMlRYMuZic6gea+oTDiqzO2Quc74TdaA8Xt9RrzZjdWkWU4IRD+XpE144MAyHFxSkXClXdfQdrM/F4mixCqJVwGPwIJX3VfsUyMBQEUClXefVyqxw7Xi6B72Luc5Nj0i8zqy4h0uHjhwrbIgUMbMUt+KfY4YtK7l3gbXLhWN/7+XQJIYnDyk3jxrslCa0L+d1zQY2pCDLuRshKuyQeZgbzQ90iwKYcsrPt1zu7bN7c3J3a0pPBVUehDzQ==
X-Microsoft-Exchange-Diagnostics: 1;BLUPR0601MB1635;31:FPynjvJrN9BMI8B3BNKoHQkq1MZPPqM9Mif8RRC77N4dy/1NVfuzSCbBPJYGZxYQfB35q8mJQr8+wQMIURjD8hck35fQcmnHgXOtwuiI90Bv8C2Wc5N1G6505tSQ5ZxLCA2DeFILxXP1EzReathqsjxXM9411zYE/+hRo/96CobErHkKQAaOQ4U98daErgLDyxfkzOgDJcagj6ez8EggXhEXWq5iTp9xPdyuORAKOIjADnlwM+sMXNr+CNw/OueblnlA2UPQprhodUnwmwBwFw==;20: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
X-Microsoft-Antispam-PRVS: <BLUPR0601MB1635ECE13E0623F977ABE259F84A0@BLUPR0601MB1635.namprd06.prod.outlook.com>
X-Exchange-Antispam-Report-Test: UriScan:;
X-Exchange-Antispam-Report-CFA-Test: BCL:0;PCL:0;RULEID:(6040375)(601004)(2401047)(5005006)(8121501046)(10201501046)(3002001)(6055026)(6041248)(20161123562025)(20161123555025)(20161123564025)(20161123560025)(6072148);SRVR:BLUPR0601MB1635;BCL:0;PCL:0;RULEID:;SRVR:BLUPR0601MB1635;
X-Microsoft-Exchange-Diagnostics: 1;BLUPR0601MB1635;4: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
X-Forefront-PRVS: 0204F0BDE2
X-Forefront-Antispam-Report: SFV:NSPM;SFS:(10009020)(4630300001)(6009001)(7916002)(39450400003)(377454003)(24454002)(189002)(199003)(6506006)(39060400001)(97736004)(42186005)(229853002)(38730400001)(4001350100001)(31686004)(54906002)(6512007)(92566002)(83506001)(36756003)(3846002)(6486002)(53936002)(69596002)(101416001)(189998001)(81166006)(76176999)(54356999)(64126003)(8676002)(50986999)(50466002)(81156014)(25786008)(47776003)(4326007)(2906002)(6666003)(106356001)(68736007)(5001770100001)(6116002)(53416004)(105586002)(66066001)(305945005)(33646002)(7736002)(5660300001)(31696002)(23676002)(86362001)(65826007)(2201001)(2950100002)(7416002)(65956001)(230700001)(65806001)(2101003);DIR:OUT;SFP:1101;SCL:1;SRVR:BLUPR0601MB1635;H:gouda.nowheycreamery.com;FPR:;SPF:None;PTR:InfoNoRecords;MX:1;A:1;LANG:en;
Received-SPF: None (protection.outlook.com: netapp.com does not designate
 permitted sender hosts)
X-Microsoft-Exchange-Diagnostics: =?utf-8?B?MTtCTFVQUjA2MDFNQjE2MzU7MjM6S1UrUys0dElrLzNLSC90RWxFUjJvNy83?=
 =?utf-8?B?WDhHRHcxaDBSVDV2STBKWGg3LzFMOWdHOGwzc3E3WWVlakpnRkV1STFmWmcw?=
 =?utf-8?B?dmdyZFhrczZGRGRuM0pQQzU2bCs3L2E3M0IzV09HWkFmK1JWenVHQ3FiRzJH?=
 =?utf-8?B?UlVQVGFNdW1vT1VVZWJxWWRZYUJhakhlVDd3NTRnU09wU3FFdXdROWkwWHhV?=
 =?utf-8?B?QTYwazdpU1NhdTlZcDErZCtDVVRNblYwY1dOUU1HY0dPcTd3U3BpNW5XdlI4?=
 =?utf-8?B?eHJlRGN3RGFiRHNEblQzcXhTc0FyZm5kdGxpUW0xbWlIeDRtSkpJWmI5MXlm?=
 =?utf-8?B?QU0ycFJuOHg4bTc4dTAyTmUxOXlKYzRFeEdrdktoQjhOUzJ4SmE1NTRiUnFY?=
 =?utf-8?B?QjMwMTRzZjBsWFd2ZDFmSFZlby81OVdQc0tPQUsyait4ZXl6cWNtdEk2OU5B?=
 =?utf-8?B?VVVubElKOGtCU1d5R3FJa3hNR2toajlKRTNKZGhsVm9haHYrdzFYMUgyUDJw?=
 =?utf-8?B?UGVidjAvNDNveklLUHg4enJJY21DbzRubWZLVnNDWWQ5bTFFQ0NoQ1VTdm8y?=
 =?utf-8?B?blRLK3dsWUZlVGtvSmZwZnJmeWpEVXFVZEViRm9ma0psb0RnKzYrQ0d0dTFz?=
 =?utf-8?B?MVFxS3lFbG9ZL0U4OE9tZVNhZkVSZThkRWptWi9lMDJKYTlvbUYyQkhKRWx4?=
 =?utf-8?B?YXlBK0ZDNkowLzZBN1RiMW5SSU9MbG5XWFd2ZXhVaG9xZG9ob2JXcUl5UDl3?=
 =?utf-8?B?SldUR25EendDamQ4U3B4L0pGWlhoYm9HVEpIUEVxSVJwYkFxbE8xcWprTllS?=
 =?utf-8?B?ajV4cW9qbnR2VXBaQ01MK3RMODNlWitvb0VuZ3B6bTRKSFdKTmsvZ1pOTisz?=
 =?utf-8?B?Sy9zZVFYYTgxTWhrT0Y2Z1lRc1d3SWV1cFJNZm1MTU5DMEpLZkpLekUyM2FX?=
 =?utf-8?B?L3dVa3FoVlNIdllOZFhmK3JkS3JOZEswdXV1RU5sVTZaR1NqM3AwSlg0NHpx?=
 =?utf-8?B?amF2bkFXSzVIVi9HSFl6RkUzRGpHK1U3UzVsNjd6bi92ZUNFc2NsV29WVzdY?=
 =?utf-8?B?RU4yV3BYZ1RQcEg0V3duMFpaeXlZODRmZnlQdEVPOXVLYklQSHY5U0lOaGRY?=
 =?utf-8?B?Y1ErdlZ4TFlLeERzMm5SOTkwMmYxL2ZNWVNxRk1UYjVRZGkvNHp4d2FvUmlv?=
 =?utf-8?B?bDZBTWpXdHpIaWdxVHp2UThoRG1KQzdVbG9sRkRnSWExYzd1L1JyUUYzVW83?=
 =?utf-8?B?aStWbW9lZjNqWThkSGxUZmllaGgvOXRzS0Zka2g3N08yT2NmQzZpWExiS1BN?=
 =?utf-8?B?SU9mWlp1eWlJRmc0dURuU2Y2WmhvSmNCcVFXV1BWUDdtekozaDRlNHRrWVVu?=
 =?utf-8?B?SSszeVllb2dISVJEUUF0Q0RqeWpieDR0M0oyYUk0cXJVL05BR2V3Z05tU0pp?=
 =?utf-8?B?SXVsZzNkUEVjVmZ4eDE2SlpudjlVVGx4NWQzSDRXbWVwNTIrVHhQbXlrQnZY?=
 =?utf-8?B?cDNnL0E0dmpxSHVra3NRS3UwSy85R3hZYklMaFNCV01FRzNFQlZzL05zM0Q4?=
 =?utf-8?B?Ulc2UXRhVmhzd0VhQ2VLZWN1NzNYWjVNL1pPMFZFSmsrU3RQaWZXYi90YlN4?=
 =?utf-8?B?dHFCQnhxTnEzeVBaZkJHSnp2bFM2djhXaDBiWE96Z1FabXZUMVR4SkFsNXpZ?=
 =?utf-8?B?WUJUZGlickl5VWNjREYwQ3ByVUd2NW9GYVhzTjllQy8vaVZhSTh5MUhJUkIw?=
 =?utf-8?B?RGFXWE1VV1hWU2tUMXpoUFpCS3ozbDFJcnpGbzVuelRHR2FWS0RmdUNCZ3gw?=
 =?utf-8?B?d214L0FQZDg5SzVMeFRFVUN1MWlSM1BmNjRVUFJBZERCUWora2lYWE1iV3FJ?=
 =?utf-8?B?ZEZ6UFh1blF1WlUzY0ZLcHV5Q1NKQy9sNWNJbGVEYmNwejl6bXhMdTNkalBo?=
 =?utf-8?B?dUNsdVQxWFQ3ODgyQk81UHhOWlJCNy80S2dXN2hZWS84ZFU0T0VXdFdGcHA4?=
 =?utf-8?B?cEJYMmdodnp2M0ExL0VwVVEvWDg0SXQvbDNRNkdBPT0=?=
X-Microsoft-Exchange-Diagnostics: 1;BLUPR0601MB1635;6:WBLtr3MXXwoiHkSwhKjB673n8OX329kgpwwMBXNqeCS/EQFBbUGHSsuqSk92sCCl2+JLRhBvCPJVKpDnluqxe7eIitEzjXfXh4mOW8U01bMeJovtsel8plK7iNeiw0+bRIpoLZi47r5AGXsxs/dmZXNRupF5ZK9F6suMm7OGKTbpHX0HyNZFESYLtBYP9agxizQkubL6c4gIh1/Yybom+vTlYV8SI+MHj7iJFYOmb+3QmtMvgf31vNll54wNpfyJgFbTnC0EhJy8byMN46lvfYLIsAILmr6trcwWxClGPxfS6clss2KZK/r3q0xkpzWNAH8m7ZBT0c65+enFhrJh7tbEXGvyS+J9jtmjqahPAkhzQXi3UqL76Q8ZbAcMJ09611t3mR1YC7rEpRQbEegkaxSnijiJ0u9NGm5cp2yUEII=;5:pzqEmbfXD1634cfC2rXSM9Esk+gpX9gLy0mBHGt1rCJgtjKgIhLKsHMeJhV9OVJsBhGKMweyrCiL4SHbK5CNwaSvWJU/ar1zjwYSoQaTjvAfMYHQ8beQC5FlSPXKD3WxSb0U5mjnfxF9q9bnzSLMfAf6WgiTrGChx9K9Y18SrBs=;24:FjvrVeHw1jlBi2zVZGiMJxIh0Rd1Giet37EvGDiMeDJJTHTGj8yitNhlxclTSa41EVFMsgjneP81dvWtuaN5qocnwo5FOjPscWHu4c6oj0k=
SpamDiagnosticOutput: 1:99
SpamDiagnosticMetadata: NSPM
X-Microsoft-Exchange-Diagnostics: 1;BLUPR0601MB1635;7: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
X-MS-Exchange-CrossTenant-OriginalArrivalTime: 31 Jan 2017 19:48:07.4192 (UTC)
X-MS-Exchange-CrossTenant-FromEntityHeader: Hosted
X-MS-Exchange-Transport-CrossTenantHeadersStamped: BLUPR0601MB1635
X-OriginatorOrg: netapp.com
Return-Path: <Anna.Schumaker@netapp.com>
X-Envelope-To: <"|/home/ecartis/ecartis -s linux-mips"> (uid 0)
X-Orcpt: rfc822;linux-mips@linux-mips.org
Original-Recipient: rfc822;linux-mips@linux-mips.org
X-archive-position: 56566
X-ecartis-version: Ecartis v1.0.0
Sender: linux-mips-bounce@linux-mips.org
Errors-to: linux-mips-bounce@linux-mips.org
X-original-sender: Anna.Schumaker@Netapp.com
Precedence: bulk
List-help: <mailto:ecartis@linux-mips.org?Subject=help>
List-unsubscribe: <mailto:ecartis@linux-mips.org?subject=unsubscribe%20linux-mips>
List-software: Ecartis version 1.0.0
List-Id: linux-mips <linux-mips.eddie.linux-mips.org>
X-List-ID: linux-mips <linux-mips.eddie.linux-mips.org>
List-subscribe: <mailto:ecartis@linux-mips.org?subject=subscribe%20linux-mips>
List-owner: <mailto:ralf@linux-mips.org>
List-post: <mailto:linux-mips@linux-mips.org>
List-archive: <http://www.linux-mips.org/archives/linux-mips/>
X-list: linux-mips
Content-Length: 1346
Lines: 36

Hi Russell,

On 01/31/2017 02:18 PM, Russell King wrote:
> Removing linux/phy.h from net/dsa.h reveals a build error in the sunrpc
> code:
> 
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_rdma_bc_put':
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c:277:2: error: implicit declaration of function 'module_put' [-Werror=implicit-function-declaration]
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function 'xprt_setup_rdma_bc':
> net/sunrpc/xprtrdma/svc_rdma_backchannel.c:348:7: error: implicit declaration of function 'try_module_get' [-Werror=implicit-function-declaration]
> 
> Fix this by adding linux/module.h to svc_rdma_backchannel.c
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

This patch looks okay to me:

Acked-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

> ---
>  net/sunrpc/xprtrdma/svc_rdma_backchannel.c | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> index 288e35c2d8f4..cb1e48e54eb1 100644
> --- a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> +++ b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
> @@ -4,6 +4,7 @@
>   * Support for backward direction RPCs on RPC/RDMA (server-side).
>   */
>  
> +#include <linux/module.h>
>  #include <linux/sunrpc/svc_rdma.h>
>  #include "xprt_rdma.h"
>  
> 

Re: [PATCH 4.10-rc3 09/13] iscsi: fix build errors when linux/phy*.h is removed from net/dsa.h

[Bart Van Assche]

On Tue, 2017-01-31 at 19:19 +0000, Russell King wrote:
> drivers/target/iscsi/iscsi_target_login.c:1135:7: error: implicit declaration of function 'try_module_get' [-Werror=implicit-function-declaration]
> 
> Add linux/module.h to iscsi_target_login.c.
> 
> Signed-off-by: Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org>
> ---
>  drivers/target/iscsi/iscsi_target_login.c | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/drivers/target/iscsi/iscsi_target_login.c b/drivers/target/iscsi/iscsi_target_login.c
> index 450f51deb2a2..eab274d17b5c 100644
> --- a/drivers/target/iscsi/iscsi_target_login.c
> +++ b/drivers/target/iscsi/iscsi_target_login.c
> @@ -17,6 +17,7 @@
>   ******************************************************************************/
>  
>  #include <crypto/hash.h>
> +#include <linux/module.h>
>  #include <linux/string.h>
>  #include <linux/kthread.h>
>  #include <linux/idr.h>

Reviewed-by: Bart Van Assche <bart.vanassche-XdAiOPVOjttBDgjK7y7TUQ@public.gmane.org>--
To unsubscribe from this list: send the line "unsubscribe linux-nfs" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 4.10-rc3 10/13] MIPS: Octeon: Remove unnecessary MODULE_*()

[Russell King]

octeon-platform.c can not be built as a module for two reasons:

(a) the Makefile doesn't allow it:
    obj-y := cpu.o setup.o octeon-platform.o octeon-irq.o csrc-octeon.o

(b) the multiple *_initcall() statements, each of which are translated
    to a module_init() call when attempting a module build, become
    aliases to init_module().  Having more than one alias will cause a
    build error.

Hence, rather than adding a linux/module.h include, remove the redundant
MODULE_*() from this file.

Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 arch/mips/cavium-octeon/octeon-platform.c | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/mips/cavium-octeon/octeon-platform.c b/arch/mips/cavium-octeon/octeon-platform.c
index 37a932d9148c..8297ce714c5e 100644
--- a/arch/mips/cavium-octeon/octeon-platform.c
+++ b/arch/mips/cavium-octeon/octeon-platform.c
@@ -1060,7 +1060,3 @@ static int __init octeon_publish_devices(void)
 	return of_platform_bus_probe(NULL, octeon_ids, NULL);
 }
 arch_initcall(octeon_publish_devices);
-
-MODULE_AUTHOR("David Daney <ddaney@caviumnetworks.com>");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Platform driver for Octeon SOC");
-- 
2.7.4

[PATCH 4.10-rc3 11/13] net: liquidio: fix build errors when linux/phy*.h is removed from net/dsa.h

[Russell King]

drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:36: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:37: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:46: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:48: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:53: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:54: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:57: error: expected ')' before 'sizeof'
drivers/net/ethernet/cavium/liquidio/lio_main.c:58: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: data definitionhas no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_recv_vf_drv_notice':
drivers/net/ethernet/cavium/liquidio/lio_main.c:4393: error: implicit declaration of function 'try_module_get'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4400: error: implicit declaration of function 'module_put'
drivers/net/ethernet/cavium/liquidio/lio_main.c: At top level:
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: parameter names (without types) in function declaration

Add linux/module.h to both these files.

drivers/net/ethernet/cavium/liquidio/octeon_console.c:40:31: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/octeon_console.c:42:4: error: expected ')' before string constant

Add linux/moduleparam.h to this file.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/net/ethernet/cavium/liquidio/lio_main.c       | 1 +
 drivers/net/ethernet/cavium/liquidio/lio_vf_main.c    | 1 +
 drivers/net/ethernet/cavium/liquidio/octeon_console.c | 1 +
 3 files changed, 3 insertions(+)

diff --git a/drivers/net/ethernet/cavium/liquidio/lio_main.c b/drivers/net/ethernet/cavium/liquidio/lio_main.c
index 39a9665c9d00..e4dd39440687 100644
--- a/drivers/net/ethernet/cavium/liquidio/lio_main.c
+++ b/drivers/net/ethernet/cavium/liquidio/lio_main.c
@@ -15,6 +15,7 @@
  * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
  * NONINFRINGEMENT.  See the GNU General Public License for more details.
  ***********************************************************************/
+#include <linux/module.h>
 #include <linux/pci.h>
 #include <linux/firmware.h>
 #include <net/vxlan.h>
diff --git a/drivers/net/ethernet/cavium/liquidio/lio_vf_main.c b/drivers/net/ethernet/cavium/liquidio/lio_vf_main.c
index 70d96c10c673..b98d29827a0d 100644
--- a/drivers/net/ethernet/cavium/liquidio/lio_vf_main.c
+++ b/drivers/net/ethernet/cavium/liquidio/lio_vf_main.c
@@ -15,6 +15,7 @@
  * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
  * NONINFRINGEMENT.  See the GNU General Public License for more details.
  ***********************************************************************/
+#include <linux/module.h>
 #include <linux/pci.h>
 #include <net/vxlan.h>
 #include "liquidio_common.h"
diff --git a/drivers/net/ethernet/cavium/liquidio/octeon_console.c b/drivers/net/ethernet/cavium/liquidio/octeon_console.c
index 3265e0b7923e..964058c55d47 100644
--- a/drivers/net/ethernet/cavium/liquidio/octeon_console.c
+++ b/drivers/net/ethernet/cavium/liquidio/octeon_console.c
@@ -18,6 +18,7 @@
 /**
  * @file octeon_console.c
  */
+#include <linux/moduleparam.h>
 #include <linux/pci.h>
 #include <linux/netdevice.h>
 #include <linux/crc32.h>
-- 
2.7.4

Re: [PATCH 4.10-rc3 11/13] net: liquidio: fix build errors when linux/phy*.h is removed from net/dsa.h

[Felix Manlunas]

Russell King <rmk+kernel@armlinux.org.uk> wrote on Tue [2017-Jan-31 19:19:19 +0000]:
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:36: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:37: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: error: type defaults to 'int' in declaration of 'module_init'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: error: type defaults to 'int' in declaration of 'module_exit'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:46: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:48: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:53: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:54: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:57: error: expected ')' before 'sizeof'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:58: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: data definitionhas no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_recv_vf_drv_notice':
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4393: error: implicit declaration of function 'try_module_get'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4400: error: implicit declaration of function 'module_put'
> drivers/net/ethernet/cavium/liquidio/lio_main.c: At top level:
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: error: type defaults to 'int' in declaration of 'module_init'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: error: type defaults to 'int' in declaration of 'module_exit'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: parameter names (without types) in function declaration
> 
> Add linux/module.h to both these files.
> 
> drivers/net/ethernet/cavium/liquidio/octeon_console.c:40:31: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/octeon_console.c:42:4: error: expected ')' before string constant
> 
> Add linux/moduleparam.h to this file.
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Acked-by: Felix Manlunas <felix.manlunas@cavium.com>

Thank you.

Re: [PATCH 4.10-rc3 11/13] net: liquidio: fix build errors when linux/phy*.h is removed from net/dsa.h

[Felix Manlunas]

Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org> wrote on Tue [2017-Jan-31 19:19:19 +0000]:
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:36: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:37: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: error: type defaults to 'int' in declaration of 'module_init'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: error: type defaults to 'int' in declaration of 'module_exit'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:46: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:48: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:53: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:54: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:57: error: expected ')' before 'sizeof'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:58: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: data definitionhas no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_recv_vf_drv_notice':
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4393: error: implicit declaration of function 'try_module_get'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4400: error: implicit declaration of function 'module_put'
> drivers/net/ethernet/cavium/liquidio/lio_main.c: At top level:
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: error: type defaults to 'int' in declaration of 'module_init'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: error: type defaults to 'int' in declaration of 'module_exit'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: parameter names (without types) in function declaration
> 
> Add linux/module.h to both these files.
> 
> drivers/net/ethernet/cavium/liquidio/octeon_console.c:40:31: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/octeon_console.c:42:4: error: expected ')' before string constant
> 
> Add linux/moduleparam.h to this file.
> 
> Signed-off-by: Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org>

Acked-by: Felix Manlunas <felix.manlunas-YGCgFSpz5w/QT0dZR+AlfA@public.gmane.org>

Thank you.

Re: [PATCH 4.10-rc3 11/13] net: liquidio: fix build errors when linux/phy*.h is removed from net/dsa.h

[Felix Manlunas]

Russell King <rmk+kernel@armlinux.org.uk> wrote on Tue [2017-Jan-31 19:19:19 +0000]:
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:36: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:37: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: error: type defaults to 'int' in declaration of 'module_init'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: error: type defaults to 'int' in declaration of 'module_exit'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:46: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:48: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:53: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:54: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:57: error: expected ')' before 'sizeof'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:58: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: data definitionhas no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_recv_vf_drv_notice':
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4393: error: implicit declaration of function 'try_module_get'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4400: error: implicit declaration of function 'module_put'
> drivers/net/ethernet/cavium/liquidio/lio_main.c: At top level:
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: error: type defaults to 'int' in declaration of 'module_init'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: error: type defaults to 'int' in declaration of 'module_exit'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: parameter names (without types) in function declaration
> 
> Add linux/module.h to both these files.
> 
> drivers/net/ethernet/cavium/liquidio/octeon_console.c:40:31: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/octeon_console.c:42:4: error: expected ')' before string constant
> 
> Add linux/moduleparam.h to this file.
> 
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Acked-by: Felix Manlunas <felix.manlunas@cavium.com>

Thank you.

Re: [PATCH 4.10-rc3 11/13] net: liquidio: fix build errors when linux/phy*.h is removed from net/dsa.h

[Felix Manlunas]

Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org> wrote on Tue [2017-Jan-31 19:19:19 +0000]:
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:36: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:37: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: error: type defaults to 'int' in declaration of 'module_init'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: error: type defaults to 'int' in declaration of 'module_exit'
> drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: expected declaration specifiers or '...' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: function declaration isn't a prototype
> drivers/net/ethernet/cavium/liquidio/lio_main.c:46: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:48: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:53: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:54: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:57: error: expected ')' before 'sizeof'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:58: error: expected ')' before string constant
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: data definitionhas no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_recv_vf_drv_notice':
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4393: error: implicit declaration of function 'try_module_get'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4400: error: implicit declaration of function 'module_put'
> drivers/net/ethernet/cavium/liquidio/lio_main.c: At top level:
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: error: type defaults to 'int' in declaration of 'module_init'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: parameter names (without types) in function declaration
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: data definition has no type or storage class
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: error: type defaults to 'int' in declaration of 'module_exit'
> drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: parameter names (without types) in function declaration
> 
> Add linux/module.h to both these files.
> 
> drivers/net/ethernet/cavium/liquidio/octeon_console.c:40:31: error: expected ')' before 'int'
> drivers/net/ethernet/cavium/liquidio/octeon_console.c:42:4: error: expected ')' before string constant
> 
> Add linux/moduleparam.h to this file.
> 
> Signed-off-by: Russell King <rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org>

Acked-by: Felix Manlunas <felix.manlunas-YGCgFSpz5w/QT0dZR+AlfA@public.gmane.org>

Thank you.

[PATCH 4.10-rc3 12/13] net: ath5k: fix build errors when linux/phy*.h is removed from net/dsa.h

[Russell King]

Fix these errors reported by the 0-day builder by replacing the
linux/export.h include with linux/module.h.

In file included from include/linux/platform_device.h:14:0,
                 from drivers/net/wireless/ath/ath5k/ahb.c:20:
include/linux/device.h:1463:1: warning: data definition has no type or storage class
 module_init(__driver##_init); \
 ^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
  module_driver(__platform_driver, platform_driver_register, \
  ^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
 module_platform_driver(ath_ahb_driver);
 ^~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:1463:1: error: type defaults to 'int' in declaration of 'module_init' [-Werror=implicit-int]
 module_init(__driver##_init); \
 ^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
  module_driver(__platform_driver, platform_driver_register, \
  ^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
 module_platform_driver(ath_ahb_driver);
 ^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
In file included from include/linux/platform_device.h:14:0,
                 from drivers/net/wireless/ath/ath5k/ahb.c:20:
include/linux/device.h:1468:1: warning: data definition has no type or storage class
 module_exit(__driver##_exit);
 ^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
  module_driver(__platform_driver, platform_driver_register, \
  ^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
 module_platform_driver(ath_ahb_driver);
 ^~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:1468:1: error: type defaults to 'int' in declaration of 'module_exit' [-Werror=implicit-int]
 module_exit(__driver##_exit);
 ^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
  module_driver(__platform_driver, platform_driver_register, \
  ^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
 module_platform_driver(ath_ahb_driver);
 ^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
In file included from include/linux/platform_device.h:14:0,
                 from drivers/net/wireless/ath/ath5k/ahb.c:20:
drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_exit' defined but not used [-Wunused-function]
 module_platform_driver(ath_ahb_driver);
                        ^
include/linux/device.h:1464:20: note: in definition of macro 'module_driver'
 static void __exit __driver##_exit(void) \
                    ^~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
 module_platform_driver(ath_ahb_driver);
 ^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_init' defined but not used [-Wunused-function]
 module_platform_driver(ath_ahb_driver);
                        ^
include/linux/device.h:1459:19: note: in definition of macro 'module_driver'
 static int __init __driver##_init(void) \
                   ^~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
 module_platform_driver(ath_ahb_driver);
 ^~~~~~~~~~~~~~~~~~~~~~

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/net/wireless/ath/ath5k/ahb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath5k/ahb.c b/drivers/net/wireless/ath/ath5k/ahb.c
index 2ca88b593e4c..c0794f5988b3 100644
--- a/drivers/net/wireless/ath/ath5k/ahb.c
+++ b/drivers/net/wireless/ath/ath5k/ahb.c
@@ -16,10 +16,10 @@
  * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
  */
 
+#include <linux/module.h>
 #include <linux/nl80211.h>
 #include <linux/platform_device.h>
 #include <linux/etherdevice.h>
-#include <linux/export.h>
 #include <ath25_platform.h>
 #include "ath5k.h"
 #include "debug.h"
-- 
2.7.4

Re: [PATCH 4.10-rc3 12/13] net: ath5k: fix build errors when linux/phy*.h is removed from net/dsa.h

[Kalle Valo]

Russell King <rmk+kernel@armlinux.org.uk> writes:

> Fix these errors reported by the 0-day builder by replacing the
> linux/export.h include with linux/module.h.
>
> In file included from include/linux/platform_device.h:14:0,
>                  from drivers/net/wireless/ath/ath5k/ahb.c:20:
> include/linux/device.h:1463:1: warning: data definition has no type or storage class
>  module_init(__driver##_init); \
>  ^
> include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
>   module_driver(__platform_driver, platform_driver_register, \
>   ^~~~~~~~~~~~~
> drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
>  module_platform_driver(ath_ahb_driver);
>  ^~~~~~~~~~~~~~~~~~~~~~
> include/linux/device.h:1463:1: error: type defaults to 'int' in declaration of 'module_init' [-Werror=implicit-int]
>  module_init(__driver##_init); \
>  ^
> include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
>   module_driver(__platform_driver, platform_driver_register, \
>   ^~~~~~~~~~~~~
> drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
>  module_platform_driver(ath_ahb_driver);
>  ^~~~~~~~~~~~~~~~~~~~~~
> drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
> In file included from include/linux/platform_device.h:14:0,
>                  from drivers/net/wireless/ath/ath5k/ahb.c:20:
> include/linux/device.h:1468:1: warning: data definition has no type or storage class
>  module_exit(__driver##_exit);
>  ^
> include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
>   module_driver(__platform_driver, platform_driver_register, \
>   ^~~~~~~~~~~~~
> drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
>  module_platform_driver(ath_ahb_driver);
>  ^~~~~~~~~~~~~~~~~~~~~~
> include/linux/device.h:1468:1: error: type defaults to 'int' in declaration of 'module_exit' [-Werror=implicit-int]
>  module_exit(__driver##_exit);
>  ^
> include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
>   module_driver(__platform_driver, platform_driver_register, \
>   ^~~~~~~~~~~~~
> drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
>  module_platform_driver(ath_ahb_driver);
>  ^~~~~~~~~~~~~~~~~~~~~~
> drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
> In file included from include/linux/platform_device.h:14:0,
>                  from drivers/net/wireless/ath/ath5k/ahb.c:20:
> drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_exit' defined but not used [-Wunused-function]
>  module_platform_driver(ath_ahb_driver);
>                         ^
> include/linux/device.h:1464:20: note: in definition of macro 'module_driver'
>  static void __exit __driver##_exit(void) \
>                     ^~~~~~~~
> drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
>  module_platform_driver(ath_ahb_driver);
>  ^~~~~~~~~~~~~~~~~~~~~~
> drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_init' defined but not used [-Wunused-function]
>  module_platform_driver(ath_ahb_driver);
>                         ^
> include/linux/device.h:1459:19: note: in definition of macro 'module_driver'
>  static int __init __driver##_init(void) \
>                    ^~~~~~~~
> drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
>  module_platform_driver(ath_ahb_driver);
>  ^~~~~~~~~~~~~~~~~~~~~~
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Looks good to me:

Acked-by: Kalle Valo <kvalo@codeaurora.org>

I assume Dave will take this so I'll drop the patch from my queue.

-- 
Kalle Valo

[PATCH 4.10-rc3 13/13] net: dsa: remove unnecessary phy*.h includes

[Russell King]

Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel.  There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.

Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.

This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.

Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/net/dsa/mv88e6xxx/mv88e6xxx.h | 1 +
 include/net/dsa.h                     | 6 ++++--
 2 files changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h b/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
index af54baea47cf..3a949095068a 100644
--- a/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
+++ b/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
@@ -15,6 +15,7 @@
 #include <linux/if_vlan.h>
 #include <linux/irq.h>
 #include <linux/gpio/consumer.h>
+#include <linux/phy.h>
 
 #ifndef UINT64_MAX
 #define UINT64_MAX		(u64)(~((u64)0))
diff --git a/include/net/dsa.h b/include/net/dsa.h
index b122196d5a1f..887b2f98f9ea 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -11,15 +11,17 @@
 #ifndef __LINUX_NET_DSA_H
 #define __LINUX_NET_DSA_H
 
+#include <linux/if.h>
 #include <linux/if_ether.h>
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/workqueue.h>
 #include <linux/of.h>
-#include <linux/phy.h>
-#include <linux/phy_fixed.h>
 #include <linux/ethtool.h>
 
+struct phy_device;
+struct fixed_phy_status;
+
 enum dsa_tag_protocol {
 	DSA_TAG_PROTO_NONE = 0,
 	DSA_TAG_PROTO_DSA,
-- 
2.7.4

Re: [PATCH 4.10-rc3 00/13] net: dsa: remove unnecessary phy.h include

[Florian Fainelli]

On 01/31/2017 11:17 AM, Russell King - ARM Linux wrote:
> Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
> unnecessary dependency for quite a large amount of the kernel.  There's
> very little which actually requires definitions from phy.h in net/dsa.h
> - the include itself only wants the declaration of a couple of
> structures and IFNAMSIZ.
> 
> Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
> mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
> and phy_fixed.h from net/dsa.h.
> 
> This patch reduces from around 800 files rebuilt to around 40 - even
> with ccache, the time difference is noticable.
> 
> In order to make this change, several drivers need to be updated to
> include necessary headers that they were picking up through this
> include.  This has resulted in a much larger patch series.
> 
> I'm assuming the 0-day builder has had 24 hours with this series, and
> hasn't reported any further issues with it - the last issue was two
> weeks ago (before I became ill) which I fixed over the last weekend.
> 
> I'm hoping this doesn't conflict with what's already in net-next...

For the entire series:

Acked-by: Florian Fainelli <f.fainelli@gmail.com>

Thanks a lot for doing that.

> 
>  arch/mips/cavium-octeon/octeon-platform.c             | 4 ----
>  drivers/net/dsa/mv88e6xxx/mv88e6xxx.h                 | 1 +
>  drivers/net/ethernet/broadcom/bgmac.c                 | 2 ++
>  drivers/net/ethernet/cadence/macb.h                   | 2 ++
>  drivers/net/ethernet/cavium/liquidio/lio_main.c       | 1 +
>  drivers/net/ethernet/cavium/liquidio/lio_vf_main.c    | 1 +
>  drivers/net/ethernet/cavium/liquidio/octeon_console.c | 1 +
>  drivers/net/ethernet/freescale/fman/fman_memac.c      | 1 +
>  drivers/net/ethernet/marvell/mvneta.c                 | 1 +
>  drivers/net/ethernet/qualcomm/emac/emac-sgmii.c       | 1 +
>  drivers/net/usb/lan78xx.c                             | 1 +
>  drivers/net/wireless/ath/ath5k/ahb.c                  | 2 +-
>  drivers/target/iscsi/iscsi_target_login.c             | 1 +
>  include/net/dsa.h                                     | 6 ++++--
>  net/core/netprio_cgroup.c                             | 1 +
>  net/sunrpc/xprtrdma/svc_rdma_backchannel.c            | 1 +
>  16 files changed, 20 insertions(+), 7 deletions(-)
> 


-- 
Florian

Re: [PATCH 4.10-rc3 00/13] net: dsa: remove unnecessary phy.h include

[Florian Fainelli]

On 01/31/2017 11:17 AM, Russell King - ARM Linux wrote:
> Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
> unnecessary dependency for quite a large amount of the kernel.  There's
> very little which actually requires definitions from phy.h in net/dsa.h
> - the include itself only wants the declaration of a couple of
> structures and IFNAMSIZ.
> 
> Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
> mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
> and phy_fixed.h from net/dsa.h.
> 
> This patch reduces from around 800 files rebuilt to around 40 - even
> with ccache, the time difference is noticable.
> 
> In order to make this change, several drivers need to be updated to
> include necessary headers that they were picking up through this
> include.  This has resulted in a much larger patch series.
> 
> I'm assuming the 0-day builder has had 24 hours with this series, and
> hasn't reported any further issues with it - the last issue was two
> weeks ago (before I became ill) which I fixed over the last weekend.
> 
> I'm hoping this doesn't conflict with what's already in net-next...

For the entire series:

Acked-by: Florian Fainelli <f.fainelli@gmail.com>

Thanks a lot for doing that.

> 
>  arch/mips/cavium-octeon/octeon-platform.c             | 4 ----
>  drivers/net/dsa/mv88e6xxx/mv88e6xxx.h                 | 1 +
>  drivers/net/ethernet/broadcom/bgmac.c                 | 2 ++
>  drivers/net/ethernet/cadence/macb.h                   | 2 ++
>  drivers/net/ethernet/cavium/liquidio/lio_main.c       | 1 +
>  drivers/net/ethernet/cavium/liquidio/lio_vf_main.c    | 1 +
>  drivers/net/ethernet/cavium/liquidio/octeon_console.c | 1 +
>  drivers/net/ethernet/freescale/fman/fman_memac.c      | 1 +
>  drivers/net/ethernet/marvell/mvneta.c                 | 1 +
>  drivers/net/ethernet/qualcomm/emac/emac-sgmii.c       | 1 +
>  drivers/net/usb/lan78xx.c                             | 1 +
>  drivers/net/wireless/ath/ath5k/ahb.c                  | 2 +-
>  drivers/target/iscsi/iscsi_target_login.c             | 1 +
>  include/net/dsa.h                                     | 6 ++++--
>  net/core/netprio_cgroup.c                             | 1 +
>  net/sunrpc/xprtrdma/svc_rdma_backchannel.c            | 1 +
>  16 files changed, 20 insertions(+), 7 deletions(-)
> 


-- 
Florian

Re: [PATCH 4.10-rc3 00/13] net: dsa: remove unnecessary phy.h include

[Florian Fainelli]

On 01/31/2017 11:17 AM, Russell King - ARM Linux wrote:
> Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
> unnecessary dependency for quite a large amount of the kernel.  There's
> very little which actually requires definitions from phy.h in net/dsa.h
> - the include itself only wants the declaration of a couple of
> structures and IFNAMSIZ.
> 
> Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
> mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
> and phy_fixed.h from net/dsa.h.
> 
> This patch reduces from around 800 files rebuilt to around 40 - even
> with ccache, the time difference is noticable.
> 
> In order to make this change, several drivers need to be updated to
> include necessary headers that they were picking up through this
> include.  This has resulted in a much larger patch series.
> 
> I'm assuming the 0-day builder has had 24 hours with this series, and
> hasn't reported any further issues with it - the last issue was two
> weeks ago (before I became ill) which I fixed over the last weekend.
> 
> I'm hoping this doesn't conflict with what's already in net-next...

For the entire series:

Acked-by: Florian Fainelli <f.fainelli@gmail.com>

Thanks a lot for doing that.

> 
>  arch/mips/cavium-octeon/octeon-platform.c             | 4 ----
>  drivers/net/dsa/mv88e6xxx/mv88e6xxx.h                 | 1 +
>  drivers/net/ethernet/broadcom/bgmac.c                 | 2 ++
>  drivers/net/ethernet/cadence/macb.h                   | 2 ++
>  drivers/net/ethernet/cavium/liquidio/lio_main.c       | 1 +
>  drivers/net/ethernet/cavium/liquidio/lio_vf_main.c    | 1 +
>  drivers/net/ethernet/cavium/liquidio/octeon_console.c | 1 +
>  drivers/net/ethernet/freescale/fman/fman_memac.c      | 1 +
>  drivers/net/ethernet/marvell/mvneta.c                 | 1 +
>  drivers/net/ethernet/qualcomm/emac/emac-sgmii.c       | 1 +
>  drivers/net/usb/lan78xx.c                             | 1 +
>  drivers/net/wireless/ath/ath5k/ahb.c                  | 2 +-
>  drivers/target/iscsi/iscsi_target_login.c             | 1 +
>  include/net/dsa.h                                     | 6 ++++--
>  net/core/netprio_cgroup.c                             | 1 +
>  net/sunrpc/xprtrdma/svc_rdma_backchannel.c            | 1 +
>  16 files changed, 20 insertions(+), 7 deletions(-)
> 


-- 
Florian