From: Maxime Ripard <maxime.ripard@bootlin.com> To: Hans Verkuil <hans.verkuil@cisco.com>, Sakari Ailus <sakari.ailus@linux.intel.com>, Mauro Carvalho Chehab <mchehab@kernel.org> Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>, Laurent Pinchart <laurent.pinchart@ideasonboard.com>, linux-media@vger.kernel.org, Andrzej Hajda <a.hajda@samsung.com>, Chen-Yu Tsai <wens@csie.org>, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org, Mark Rutland <mark.rutland@arm.com>, Rob Herring <robh+dt@kernel.org>, Frank Rowand <frowand.list@gmail.com>, Maxime Ripard <maxime.ripard@bootlin.com> Subject: [PATCH v2 5/5] DO NOT MERGE: ARM: dts: bananapi: Add Camera support Date: Mon, 28 Jan 2019 15:52:36 +0100 [thread overview] Message-ID: <b1279df2faefbb50120270417c3f5d66bb52df18.1548687041.git-series.maxime.ripard@bootlin.com> (raw) In-Reply-To: <cover.ba7411f0c7155d0292b38d3dec698e26b5cc813b.1548687041.git-series.maxime.ripard@bootlin.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> --- arch/arm/boot/dts/sun7i-a20-bananapi.dts | 94 +++++++++++++++++++++++++- 1 file changed, 94 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/sun7i-a20-bananapi.dts index 556b1b591c5d..f5fee1f95900 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapi.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapi.dts @@ -54,6 +54,9 @@ compatible = "lemaker,bananapi", "allwinner,sun7i-a20"; aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; serial0 = &uart0; serial1 = &uart3; serial2 = &uart7; @@ -63,6 +66,41 @@ stdout-path = "serial0:115200n8"; }; + reg_cam: cam { + compatible = "regulator-fixed"; + regulator-name = "cam"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <®_vcc5v0>; + gpio = <&pio 7 16 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_cam_avdd: cam-avdd { + compatible = "regulator-fixed"; + regulator-name = "cam500b-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_cam>; + }; + + reg_cam_dovdd: cam-dovdd { + compatible = "regulator-fixed"; + regulator-name = "cam500b-dovdd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <®_cam>; + }; + + reg_cam_dvdd: cam-dvdd { + compatible = "regulator-fixed"; + regulator-name = "cam500b-dvdd"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + vin-supply = <®_cam>; + }; + hdmi-connector { compatible = "hdmi-connector"; type = "a"; @@ -116,6 +154,26 @@ >; }; +&csi0 { + pinctrl-names = "default"; + pinctrl-0 = <&csi0_pins_a>; + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + csi_from_ov5640: endpoint { + remote-endpoint = <&ov5640_to_csi>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; +}; + &de { status = "okay"; }; @@ -161,6 +219,36 @@ }; }; +&i2c1 { + status = "okay"; + + camera: camera@21 { + compatible = "ovti,ov5640"; + reg = <0x21>; + clocks = <&ccu CLK_CSI0>; + clock-names = "xclk"; + assigned-clocks = <&ccu CLK_CSI0>; + assigned-clock-rates = <24000000>; + + reset-gpios = <&pio 7 14 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; + AVDD-supply = <®_cam_avdd>; + DOVDD-supply = <®_cam_dovdd>; + DVDD-supply = <®_cam_dvdd>; + + port { + ov5640_to_csi: endpoint { + remote-endpoint = <&csi_from_ov5640>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; +}; + &i2c2 { status = "okay"; }; @@ -242,6 +330,12 @@ "IO-6", "IO-3", "IO-2", "IO-0", "", "", "", "", "", "", "", "", "", "", "", ""; + csi0_pins_a: csi_pins_a@0 { + pins = "PE0", "PE1", "PE2", "PE3", "PE4", "PE5", + "PE6", "PE7", "PE8", "PE9", "PE10", "PE11"; + function = "csi0"; + }; + usb0_id_detect_pin: usb0-id-detect-pin { pins = "PH4"; function = "gpio_in"; -- git-series 0.9.1
WARNING: multiple messages have this Message-ID (diff)
From: Maxime Ripard <maxime.ripard@bootlin.com> To: Hans Verkuil <hans.verkuil@cisco.com>, Sakari Ailus <sakari.ailus@linux.intel.com>, Mauro Carvalho Chehab <mchehab@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com>, devicetree@vger.kernel.org, Maxime Ripard <maxime.ripard@bootlin.com>, linux-kernel@vger.kernel.org, Andrzej Hajda <a.hajda@samsung.com>, Chen-Yu Tsai <wens@csie.org>, Rob Herring <robh+dt@kernel.org>, Laurent Pinchart <laurent.pinchart@ideasonboard.com>, Thomas Petazzoni <thomas.petazzoni@bootlin.com>, Frank Rowand <frowand.list@gmail.com>, linux-arm-kernel@lists.infradead.org, linux-media@vger.kernel.org Subject: [PATCH v2 5/5] DO NOT MERGE: ARM: dts: bananapi: Add Camera support Date: Mon, 28 Jan 2019 15:52:36 +0100 [thread overview] Message-ID: <b1279df2faefbb50120270417c3f5d66bb52df18.1548687041.git-series.maxime.ripard@bootlin.com> (raw) In-Reply-To: <cover.ba7411f0c7155d0292b38d3dec698e26b5cc813b.1548687041.git-series.maxime.ripard@bootlin.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> --- arch/arm/boot/dts/sun7i-a20-bananapi.dts | 94 +++++++++++++++++++++++++- 1 file changed, 94 insertions(+) diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/sun7i-a20-bananapi.dts index 556b1b591c5d..f5fee1f95900 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapi.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapi.dts @@ -54,6 +54,9 @@ compatible = "lemaker,bananapi", "allwinner,sun7i-a20"; aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; serial0 = &uart0; serial1 = &uart3; serial2 = &uart7; @@ -63,6 +66,41 @@ stdout-path = "serial0:115200n8"; }; + reg_cam: cam { + compatible = "regulator-fixed"; + regulator-name = "cam"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <®_vcc5v0>; + gpio = <&pio 7 16 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_cam_avdd: cam-avdd { + compatible = "regulator-fixed"; + regulator-name = "cam500b-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_cam>; + }; + + reg_cam_dovdd: cam-dovdd { + compatible = "regulator-fixed"; + regulator-name = "cam500b-dovdd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <®_cam>; + }; + + reg_cam_dvdd: cam-dvdd { + compatible = "regulator-fixed"; + regulator-name = "cam500b-dvdd"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + vin-supply = <®_cam>; + }; + hdmi-connector { compatible = "hdmi-connector"; type = "a"; @@ -116,6 +154,26 @@ >; }; +&csi0 { + pinctrl-names = "default"; + pinctrl-0 = <&csi0_pins_a>; + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + csi_from_ov5640: endpoint { + remote-endpoint = <&ov5640_to_csi>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; +}; + &de { status = "okay"; }; @@ -161,6 +219,36 @@ }; }; +&i2c1 { + status = "okay"; + + camera: camera@21 { + compatible = "ovti,ov5640"; + reg = <0x21>; + clocks = <&ccu CLK_CSI0>; + clock-names = "xclk"; + assigned-clocks = <&ccu CLK_CSI0>; + assigned-clock-rates = <24000000>; + + reset-gpios = <&pio 7 14 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; + AVDD-supply = <®_cam_avdd>; + DOVDD-supply = <®_cam_dovdd>; + DVDD-supply = <®_cam_dvdd>; + + port { + ov5640_to_csi: endpoint { + remote-endpoint = <&csi_from_ov5640>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; +}; + &i2c2 { status = "okay"; }; @@ -242,6 +330,12 @@ "IO-6", "IO-3", "IO-2", "IO-0", "", "", "", "", "", "", "", "", "", "", "", ""; + csi0_pins_a: csi_pins_a@0 { + pins = "PE0", "PE1", "PE2", "PE3", "PE4", "PE5", + "PE6", "PE7", "PE8", "PE9", "PE10", "PE11"; + function = "csi0"; + }; + usb0_id_detect_pin: usb0-id-detect-pin { pins = "PH4"; function = "gpio_in"; -- git-series 0.9.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-01-28 14:53 UTC|newest] Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-01-28 14:52 [PATCH v2 0/5] media: Allwinner A10 CSI support Maxime Ripard 2019-01-28 14:52 ` Maxime Ripard 2019-01-28 14:52 ` [PATCH v2 1/5] dt-bindings: media: Add Allwinner A10 CSI binding Maxime Ripard 2019-01-28 14:52 ` Maxime Ripard 2019-01-28 16:17 ` Rob Herring 2019-01-28 16:17 ` Rob Herring 2019-01-28 16:17 ` Rob Herring 2019-01-29 11:52 ` Sakari Ailus 2019-01-29 11:52 ` Sakari Ailus 2019-01-29 11:52 ` Sakari Ailus 2019-01-28 14:52 ` [PATCH v2 2/5] media: sunxi: Refactor the Makefile and Kconfig Maxime Ripard 2019-01-28 14:52 ` Maxime Ripard 2019-01-28 14:52 ` Maxime Ripard 2019-01-28 14:52 ` [PATCH v2 3/5] media: sunxi: Add A10 CSI driver Maxime Ripard 2019-01-28 14:52 ` Maxime Ripard 2019-01-29 12:39 ` Sakari Ailus 2019-01-29 12:39 ` Sakari Ailus 2019-02-06 21:16 ` Maxime Ripard 2019-02-06 21:16 ` Maxime Ripard 2019-02-08 23:17 ` Sakari Ailus 2019-02-08 23:17 ` Sakari Ailus 2019-02-06 22:59 ` Ezequiel Garcia 2019-02-06 22:59 ` Ezequiel Garcia 2019-02-08 20:19 ` Maxime Ripard 2019-02-08 20:19 ` Maxime Ripard 2019-01-28 14:52 ` [PATCH v2 4/5] ARM: dts: sun7i: Add CSI0 controller Maxime Ripard 2019-01-28 14:52 ` Maxime Ripard 2019-01-28 14:52 ` Maxime Ripard [this message] 2019-01-28 14:52 ` [PATCH v2 5/5] DO NOT MERGE: ARM: dts: bananapi: Add Camera support Maxime Ripard
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=b1279df2faefbb50120270417c3f5d66bb52df18.1548687041.git-series.maxime.ripard@bootlin.com \ --to=maxime.ripard@bootlin.com \ --cc=a.hajda@samsung.com \ --cc=devicetree@vger.kernel.org \ --cc=frowand.list@gmail.com \ --cc=hans.verkuil@cisco.com \ --cc=laurent.pinchart@ideasonboard.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-media@vger.kernel.org \ --cc=mark.rutland@arm.com \ --cc=mchehab@kernel.org \ --cc=robh+dt@kernel.org \ --cc=sakari.ailus@linux.intel.com \ --cc=thomas.petazzoni@bootlin.com \ --cc=wens@csie.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.