[PATCH 00/13] Nokia RX-51: Fix USB TTY console and enable it

[Lokesh Vutla <lokeshvutla@ti.com>]

Hi Lukasz,

On 29/11/20 10:16 pm, Pali Roh?r wrote:
> This patch series fix usbtty code (serial console via USB peripheral
> mode), fix underlying musb peripheral code, fix compilation of
> CONFIG_USB_DEVICE (used by usbtty), remove unused Nokia RX-51 code to
> decrease size of U-Boot binary and finally enable usbtty serial console
> for Nokia RX-51.
> 
> With this patch series debugging of Nokia RX-51 can be done also via USB
> serial console.
> 
> On computer this serial console is accessible via /dev/ttyACM0 device.
> 
> With current implementation there is an issue in musb driver that it
> loose receiving bytes from USB bus when too many a characters are send
> over USB tty from computer. Typing on keyboard to kermit terminal
> connected to /dev/ttyACM0 is working fine. But pasting more more bytes
> to terminal cause data lost on receiving side. I do not know where is
> the issue or how to fix it (it looks like that data are lost at low
> level when reading them from msub FIFO hardware) but typing on keyboard
> is working fine. This is rather issue for sending files via x/y/z-modem
> or kermit protocol. Currently U-Boot is not able to receive any file
> via usbtty with musb driver due to this issue.

Can you take a look at usb related patches and merge them if you are okay with it?

Thanks and regards,
Lokesh

> 
> Pali Roh?r (13):
>   serial: usbtty: Fix puts function
>   usb: musb: Fix compilation of gadget code
>   usb: musb: Always clear the data toggle bit when configuring ep
>   usb: musb: Fix configuring FIFO for endpoints
>   usb: musb: Read value of PERI_RXCSR to 16bit variable
>   usb: musb: Fix transmission of bigger buffers
>   usb: gadget: Do not export usbd_device_* arrays
>   usb: gadget: Use dbg_ep0() macro instead of serial_printf()
>   arm: omap3: Compile lowlevel_init() function only when it is used
>   arm: omap3: Compile s_init() function only when it is used
>   Nokia RX-51: Remove function set_muxconf_regs()
>   Nokia RX-51: Move content of rx51.h to rx51.c
>   Nokia RX-51: Enable usbtty serial console by default
> 
>  Makefile                                  |   1 +
>  arch/arm/mach-omap2/omap3/board.c         |   3 +
>  arch/arm/mach-omap2/omap3/lowlevel_init.S |   6 +-
>  board/nokia/rx51/rx51.c                   |  28 +-
>  board/nokia/rx51/rx51.h                   | 377 ----------------------
>  configs/nokia_rx51_defconfig              |   6 +-
>  doc/README.nokia_rx51                     |  15 +-
>  drivers/serial/usbtty.c                   |   4 +-
>  drivers/usb/gadget/core.c                 |  38 +--
>  drivers/usb/gadget/ep0.c                  |  47 ++-
>  drivers/usb/musb/musb_core.c              |  10 +-
>  drivers/usb/musb/musb_udc.c               |  19 +-
>  include/configs/nokia_rx51.h              |  16 +-
>  include/usbdevice.h                       |  15 -
>  14 files changed, 92 insertions(+), 493 deletions(-)
>  delete mode 100644 board/nokia/rx51/rx51.h
>