[U-Boot] [PATCH v1 1/4] arm: socfpga: imply SPL config instead of select

[Marek Vasut <marex@denx.de>]

On 1/14/19 7:58 PM, Simon Goldschmidt wrote:
> Am 14.01.2019 um 19:31 schrieb Marek Vasut:
>> On 1/14/19 5:05 PM, Simon Goldschmidt wrote:
>>> Hi Dinh,
>>
>> Hi,
>>
>>> Am 14.01.2019 um 16:58 schrieb Dinh Nguyen:
>>>> Hi Simon,
>>>>
>>>> On 1/14/19 9:50 AM, Simon Goldschmidt wrote:
>>>>> Am 11.01.2019 um 23:02 schrieb Marek Vasut:
>>>>>> On 1/11/19 9:39 PM, Simon Goldschmidt wrote:
>>>>>>> Am 07.01.2019 um 23:53 schrieb Marek Vasut:
>>>>>>>> On 1/7/19 10:14 PM, Simon Goldschmidt wrote:
>>>>>>>>> In order to build a smaller SPL, let's imply SPL_DM_RESET and
>>>>>>>>> SPL_WATCHDOG_SUPPORT instead of selecting them, so they can be
>>>>>>>>> disabled
>>>>>>>>> via defconfig.
>>>>>>>>>
>>>>>>>>> This also seems to be required to use OF_PLATDATA, as the reset
>>>>>>>>> drivers
>>>>>>>>> don't seem to work with it.
>>>>>>>>
>>>>>>>> How do you un-reset IP blocks if you disable the reset controller ?
>>>>>>>
>>>>>>> I found that out just now: there's the function
>>>>>>> 'reset_deassert_peripherals_handoff()' in spl_gen5.c that should
>>>>>>> "De-assert reset for peripherals and bridges based on handoff".
>>>>>>> However,
>>>>>>> at least for Gen5, it just writes a 0 to rstmgr->permodrst. By doing
>>>>>>> that, it enables *ALL* peripherals on the SoC (except for some DMA
>>>>>>> channels that aren't really used) :-)
>>>>>>>
>>>>>>> I guess that needs some cleaning up as well ;-)
>>>>>>
>>>>>> Yes
>>>>>>
>>>>>>> I think the proper thing to do here would be to remove this
>>>>>>> function and
>>>>>>> convert all drivers to provide appropriate 'resets' properties in
>>>>>>> the
>>>>>>> dts?
>>>>>>
>>>>>> Indeed
>>>>>
>>>>> So I just did that and it works nice for SPL and U-Boot: By adding
>>>>> some
>>>>> "resets" properties the the main dtsi and adding reset bulk code to
>>>>> the
>>>>> cadence_qspi, denali_dt nand and drivers, I can nearly remove the
>>>>> reset
>>>>> code from arch/mach_socfpga.
>>>>>
>>>>> The problem would be that now Linux cannot use peripherals that aren't
>>>>> enabled by U-Boot because it relies on them being enabled. How are
>>>>> such
>>>>> dependencies solved? Because even if I would add reset support in the
>>>>> corresponding Linux drivers, we probably could not bootolder Kernels
>>>>> (e.g. the Debian 9 kernel - v4.9.x) with a new U-Boot...
>>>>>
>>>>
>>>> I added an early reset driver for SoCFPGA that should take care of
>>>> this.
>>>> The patch is in v5.0-rc2[1].
>>>
>>> OK, it's good to know that this work is already done, I haven't
>>> monitored this close enough.
>>
>> We had the same problem with A10, indeed.
>>
>>> But am I correct that my above problem remains even in v5.0 as not all
>>> peripherals in socfpga.dtsi have a "resets" property set (e.g. mmc and
>>> qspi) and would thuse not be taken out of reset by Linux?
>>>
>>> Plus: should U-Boot work with older Linux kernels? Because if so, we
>>> need fallback code in U-Boot to unreset peripherals when running with an
>>> older kernel...
>>
>> Yes, it'd break old broken kernels . The real question is, do we care ?
> 
> Ok, so that at leat shows me I'm going into the right direction :-)
> 
> There are some problems though:
> - I do care (we're running 4.9 currently) *g*
> - people running an RT kernel will care for a while (until the next
> stable RT after fixing this will be released)
> - we would currently be breaking *all* kernels, since no kernel should
> yet be able to deassert reset for mmc and qspi (unless this is already
> done by U-Boot)...
> 
> So would it be OK to add a Kconfig option to U-Boot to keep the current
> behaviour (for old broken kernels like you said) until that code is
> spread widely enough? Or is that a no-go?

Would be nice to be able to tweak the reset driver behavior at runtime,
to unreset things before booting the kernel if the user desires so.

-- 
Best regards,
Marek Vasut