[PATCH v13 0/6] mt8183 dpi supports dual edge and pin mode swap

[PATCH v13 0/6] mt8183 dpi supports dual edge and pin mode swap

[Jitao Shi]

Changes since v12:
 - fix mediatek,dpi.yaml make_dt_binding_check errors.

Change since v11:
 - fine tune mediatek,dpi.yaml.
 - add Acked-by: Rob Herring <robh@kernel.org>.

Change since v10:
 - convert the Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
   to yaml format.
 - read the pclk-sample in endpoint.

Changes since v9:
 - rename pinctrl-names = "gpiomode", "dpimode" to "active", "idle".
 - fix some typo.

Changes since v8:
 - drop pclk-sample redefine in mediatek,dpi.txt
 - only get the gpiomode and dpimode when dpi->pinctrl is successful.

Changes since v7:
 - separate dt-bindings to independent patches.
 - move dpi dual edge to one patch.

Changes since v6:
 - change dual_edge to pclk-sample
 - remove dpi_pin_mode_swap and

Changes since v5:
 - fine tune the dt-bindings commit message.

Changes since v4:
 - move pin mode control and dual edge control to deveice tree.
 - update dt-bindings document for pin mode swap and dual edge control.

Changes since v3:
 - add dpi pin mode control when dpi on or off.
 - update dpi dual edge comment.

Changes since v2:
 - update dt-bindings document for mt8183 dpi.
 - separate dual edge modfication as independent patch.

Jitao Shi (6):
  dt-bindings: media: add pclk-sample dual edge property
  dt-bindings: display: mediatek: control dpi pins mode to avoid leakage
  dt-bindings: display: mediatek: dpi sample data in dual edge support
  dt-bindings: display: mediatek: convert the document format from txt
    to yaml
  drm/mediatek: dpi sample mode support
  drm/mediatek: set dpi pin mode to gpio low to avoid leakage current

 .../display/mediatek/mediatek,dpi.txt         |  36 ------
 .../display/mediatek/mediatek,dpi.yaml        | 103 ++++++++++++++++++
 .../bindings/media/video-interfaces.txt       |   4 +-
 drivers/gpu/drm/mediatek/mtk_dpi.c            |  58 +++++++++-
 4 files changed, 161 insertions(+), 40 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
 create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml

-- 
2.21.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v13 1/6] dt-bindings: media: add pclk-sample dual edge property

[Jitao Shi]

Some chips's sample mode are rising, falling and dual edge (both
falling and rising edge).
Extern the pclk-sample property to support dual edge.

Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 Documentation/devicetree/bindings/media/video-interfaces.txt | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt
index f884ada0bffc..da9ad24935db 100644
--- a/Documentation/devicetree/bindings/media/video-interfaces.txt
+++ b/Documentation/devicetree/bindings/media/video-interfaces.txt
@@ -118,8 +118,8 @@ Optional endpoint properties
 - data-enable-active: similar to HSYNC and VSYNC, specifies the data enable
   signal polarity.
 - field-even-active: field signal level during the even field data transmission.
-- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
-  signal.
+- pclk-sample: sample data on rising (1), falling (0) or both rising and
+  falling (2) edge of the pixel clock signal.
 - sync-on-green-active: active state of Sync-on-green (SoG) signal, 0/1 for
   LOW/HIGH respectively.
 - data-lanes: an array of physical data lane indexes. Position of an entry
-- 
2.21.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v13 1/6] dt-bindings: media: add pclk-sample dual edge property

[Neil Armstrong]

Hi,

On 11/03/2020 08:18, Jitao Shi wrote:
> Some chips's sample mode are rising, falling and dual edge (both
> falling and rising edge).
> Extern the pclk-sample property to support dual edge.
> 
> Acked-by: Rob Herring <robh@kernel.org>
> Reviewed-by: CK Hu <ck.hu@mediatek.com>
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  Documentation/devicetree/bindings/media/video-interfaces.txt | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt
> index f884ada0bffc..da9ad24935db 100644
> --- a/Documentation/devicetree/bindings/media/video-interfaces.txt
> +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt
> @@ -118,8 +118,8 @@ Optional endpoint properties
>  - data-enable-active: similar to HSYNC and VSYNC, specifies the data enable
>    signal polarity.
>  - field-even-active: field signal level during the even field data transmission.
> -- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
> -  signal.
> +- pclk-sample: sample data on rising (1), falling (0) or both rising and
> +  falling (2) edge of the pixel clock signal.
>  - sync-on-green-active: active state of Sync-on-green (SoG) signal, 0/1 for
>    LOW/HIGH respectively.
>  - data-lanes: an array of physical data lane indexes. Position of an entry
> 

This changes the bus format, but we recently introduced a bus format negociation
between bridges to avoid adding such properties into DT, and make bus format setup
dynamic between an encoder and a bridge.

It would be great to use that instead.

Neil
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v13 1/6] dt-bindings: media: add pclk-sample dual edge property

[Chun-Kuang Hu]

Hi, Jitao:

I agree with Neil, so please base on Boris' effort to negotiate with bridge.

Regards,
Chun-Kuang Hu

Neil Armstrong <narmstrong@baylibre.com> 於 2020年3月11日 週三 下午9:53寫道：

>
> Hi,
>
> On 11/03/2020 08:18, Jitao Shi wrote:
> > Some chips's sample mode are rising, falling and dual edge (both
> > falling and rising edge).
> > Extern the pclk-sample property to support dual edge.
> >
> > Acked-by: Rob Herring <robh@kernel.org>
> > Reviewed-by: CK Hu <ck.hu@mediatek.com>
> > Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> > ---
> >  Documentation/devicetree/bindings/media/video-interfaces.txt | 4 ++--
> >  1 file changed, 2 insertions(+), 2 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt
> > index f884ada0bffc..da9ad24935db 100644
> > --- a/Documentation/devicetree/bindings/media/video-interfaces.txt
> > +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt
> > @@ -118,8 +118,8 @@ Optional endpoint properties
> >  - data-enable-active: similar to HSYNC and VSYNC, specifies the data enable
> >    signal polarity.
> >  - field-even-active: field signal level during the even field data transmission.
> > -- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
> > -  signal.
> > +- pclk-sample: sample data on rising (1), falling (0) or both rising and
> > +  falling (2) edge of the pixel clock signal.
> >  - sync-on-green-active: active state of Sync-on-green (SoG) signal, 0/1 for
> >    LOW/HIGH respectively.
> >  - data-lanes: an array of physical data lane indexes. Position of an entry
> >
>
> This changes the bus format, but we recently introduced a bus format negociation
> between bridges to avoid adding such properties into DT, and make bus format setup
> dynamic between an encoder and a bridge.
>
> It would be great to use that instead.
>
> Neil
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v13 2/6] dt-bindings: display: mediatek: control dpi pins mode to avoid leakage

[Jitao Shi]

Add property "pinctrl-names" to swap pin mode between gpio and dpi mode. Set
the dpi pins to gpio mode and output-low to avoid leakage current when dpi
disabled.

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 .../devicetree/bindings/display/mediatek/mediatek,dpi.txt  | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
index 58914cf681b8..260ae75ac640 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
@@ -17,6 +17,10 @@ Required properties:
   Documentation/devicetree/bindings/graph.txt. This port should be connected
   to the input port of an attached HDMI or LVDS encoder chip.
 
+Optional properties:
+- pinctrl-names: Contain "default" and "sleep".
+  pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
+
 Example:
 
 dpi0: dpi@1401d000 {
@@ -27,6 +31,9 @@ dpi0: dpi@1401d000 {
 		 <&mmsys CLK_MM_DPI_ENGINE>,
 		 <&apmixedsys CLK_APMIXED_TVDPLL>;
 	clock-names = "pixel", "engine", "pll";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dpi_pin_func>;
+	pinctrl-1 = <&dpi_pin_idle>;
 
 	port {
 		dpi0_out: endpoint {
-- 
2.21.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v13 2/6] dt-bindings: display: mediatek: control dpi pins mode to avoid leakage

[Chun-Kuang Hu]

[-- Attachment #1.1: Type: text/plain, Size: 1839 bytes --]

Jitao Shi <jitao.shi@mediatek.com> 於 2020年3月11日 週三 下午3:18寫道：

> Add property "pinctrl-names" to swap pin mode between gpio and dpi mode.
> Set
> the dpi pins to gpio mode and output-low to avoid leakage current when dpi
> disabled.
>

Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>


>
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  .../devicetree/bindings/display/mediatek/mediatek,dpi.txt  | 7 +++++++
>  1 file changed, 7 insertions(+)
>
> diff --git
> a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> index 58914cf681b8..260ae75ac640 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> @@ -17,6 +17,10 @@ Required properties:
>    Documentation/devicetree/bindings/graph.txt. This port should be
> connected
>    to the input port of an attached HDMI or LVDS encoder chip.
>
> +Optional properties:
> +- pinctrl-names: Contain "default" and "sleep".
> +  pinctrl-names see
> Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
> +
>  Example:
>
>  dpi0: dpi@1401d000 {
> @@ -27,6 +31,9 @@ dpi0: dpi@1401d000 {
>                  <&mmsys CLK_MM_DPI_ENGINE>,
>                  <&apmixedsys CLK_APMIXED_TVDPLL>;
>         clock-names = "pixel", "engine", "pll";
> +       pinctrl-names = "default", "sleep";
> +       pinctrl-0 = <&dpi_pin_func>;
> +       pinctrl-1 = <&dpi_pin_idle>;
>
>         port {
>                 dpi0_out: endpoint {
> --
> 2.21.0
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
>

[-- Attachment #1.2: Type: text/html, Size: 3989 bytes --]

[-- Attachment #2: Type: text/plain, Size: 160 bytes --]

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v13 2/6] dt-bindings: display: mediatek: control dpi pins mode to avoid leakage

[Rob Herring]

On Wed, Mar 11, 2020 at 03:18:19PM +0800, Jitao Shi wrote:
> Add property "pinctrl-names" to swap pin mode between gpio and dpi mode. Set
> the dpi pins to gpio mode and output-low to avoid leakage current when dpi
> disabled.
> 
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  .../devicetree/bindings/display/mediatek/mediatek,dpi.txt  | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> index 58914cf681b8..260ae75ac640 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> @@ -17,6 +17,10 @@ Required properties:
>    Documentation/devicetree/bindings/graph.txt. This port should be connected
>    to the input port of an attached HDMI or LVDS encoder chip.
>  
> +Optional properties:
> +- pinctrl-names: Contain "default" and "sleep".

> +  pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt

Drop this line.

> +
>  Example:
>  
>  dpi0: dpi@1401d000 {
> @@ -27,6 +31,9 @@ dpi0: dpi@1401d000 {
>  		 <&mmsys CLK_MM_DPI_ENGINE>,
>  		 <&apmixedsys CLK_APMIXED_TVDPLL>;
>  	clock-names = "pixel", "engine", "pll";
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&dpi_pin_func>;
> +	pinctrl-1 = <&dpi_pin_idle>;
>  
>  	port {
>  		dpi0_out: endpoint {
> -- 
> 2.21.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v13 3/6] dt-bindings: display: mediatek: dpi sample data in dual edge support

[Jitao Shi]

Add property "pclk-sample" to config the dpi sample on falling (0),
rising (1), both falling and rising (2).

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 .../devicetree/bindings/display/mediatek/mediatek,dpi.txt       | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
index 260ae75ac640..2dfb50a7321e 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
@@ -20,6 +20,7 @@ Required properties:
 Optional properties:
 - pinctrl-names: Contain "default" and "sleep".
   pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
+- pclk-sample: refer Documentation/devicetree/bindings/media/video-interfaces.txt.
 
 Example:
 
@@ -37,6 +38,7 @@ dpi0: dpi@1401d000 {
 
 	port {
 		dpi0_out: endpoint {
+			pclk-sample = <0>;
 			remote-endpoint = <&hdmi0_in>;
 		};
 	};
-- 
2.21.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v13 4/6] dt-bindings: display: mediatek: convert the document format from txt to yaml

[Jitao Shi]

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 .../display/mediatek/mediatek,dpi.txt         |  45 --------
 .../display/mediatek/mediatek,dpi.yaml        | 103 ++++++++++++++++++
 2 files changed, 103 insertions(+), 45 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
 create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml

diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
deleted file mode 100644
index 2dfb50a7321e..000000000000
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
+++ /dev/null
@@ -1,45 +0,0 @@
-Mediatek DPI Device
-===================
-
-The Mediatek DPI function block is a sink of the display subsystem and
-provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
-output bus.
-
-Required properties:
-- compatible: "mediatek,<chip>-dpi"
-  the supported chips are mt2701 , mt8173 and mt8183.
-- reg: Physical base address and length of the controller's registers
-- interrupts: The interrupt signal from the function block.
-- clocks: device clocks
-  See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
-- clock-names: must contain "pixel", "engine", and "pll"
-- port: Output port node with endpoint definitions as described in
-  Documentation/devicetree/bindings/graph.txt. This port should be connected
-  to the input port of an attached HDMI or LVDS encoder chip.
-
-Optional properties:
-- pinctrl-names: Contain "default" and "sleep".
-  pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
-- pclk-sample: refer Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Example:
-
-dpi0: dpi@1401d000 {
-	compatible = "mediatek,mt8173-dpi";
-	reg = <0 0x1401d000 0 0x1000>;
-	interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&mmsys CLK_MM_DPI_PIXEL>,
-		 <&mmsys CLK_MM_DPI_ENGINE>,
-		 <&apmixedsys CLK_APMIXED_TVDPLL>;
-	clock-names = "pixel", "engine", "pll";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&dpi_pin_func>;
-	pinctrl-1 = <&dpi_pin_idle>;
-
-	port {
-		dpi0_out: endpoint {
-			pclk-sample = <0>;
-			remote-endpoint = <&hdmi0_in>;
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
new file mode 100644
index 000000000000..d65543e3bf8c
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
@@ -0,0 +1,103 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/mediatek/mediatek,dpi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: mediatek DPI Controller Device Tree Bindings
+
+maintainers:
+  - CK Hu <ck.hu@mediatek.com>
+  - Jitao shi <jitao.shi@mediatek.com>
+
+description: |
+  The Mediatek DPI function block is a sink of the display subsystem and
+  provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
+  output bus.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-dpi
+      - mediatek,mt8173-dpi
+      - mediatek,mt8183-dpi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Pixel Clock
+      - description: Engine Clock
+      - description: DPI PLL
+
+  clock-names:
+    items:
+      - const: pixel
+      - const: engine
+      - const: pll
+
+  pinctrl-0: true
+  pinctrl-1: true
+
+  pinctrl-names:
+    items:
+      - const: default
+      - const: sleep
+
+  port@0:
+    type: object
+    description:
+      Output port node with endpoint definitions as described in
+      Documentation/devicetree/bindings/graph.txt. This port should be connected
+      to the input port of an attached HDMI or LVDS encoder chip.
+
+    properties:
+      endpoint:
+        type: object
+
+        properties:
+          pclk-sample:
+            items:
+            - description: refer Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - port@0
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/mt8173-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    dpi0: dpi@1401d000 {
+        compatible = "mediatek,mt8173-dpi";
+        reg = <0 0x1401d000 0 0x1000>;
+        interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
+        clocks = <&mmsys CLK_MM_DPI_PIXEL>,
+             <&mmsys CLK_MM_DPI_ENGINE>,
+             <&apmixedsys CLK_APMIXED_TVDPLL>;
+        clock-names = "pixel", "engine", "pll";
+        pinctrl-names = "default", "sleep";
+        pinctrl-0 = <&dpi_pin_func>;
+        pinctrl-1 = <&dpi_pin_idle>;
+
+        port@0 {
+            dpi0_out: endpoint {
+                pclk-sample = <0>;
+                remote-endpoint = <&hdmi0_in>;
+            };
+        };
+    };
+
+...
-- 
2.21.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v13 4/6] dt-bindings: display: mediatek: convert the document format from txt to yaml

[Rob Herring]

On Wed, Mar 11, 2020 at 03:18:21PM +0800, Jitao Shi wrote:
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  .../display/mediatek/mediatek,dpi.txt         |  45 --------
>  .../display/mediatek/mediatek,dpi.yaml        | 103 ++++++++++++++++++
>  2 files changed, 103 insertions(+), 45 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
>  create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
> 
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> deleted file mode 100644
> index 2dfb50a7321e..000000000000
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ /dev/null
> @@ -1,45 +0,0 @@
> -Mediatek DPI Device
> -===================
> -
> -The Mediatek DPI function block is a sink of the display subsystem and
> -provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
> -output bus.
> -
> -Required properties:
> -- compatible: "mediatek,<chip>-dpi"
> -  the supported chips are mt2701 , mt8173 and mt8183.
> -- reg: Physical base address and length of the controller's registers
> -- interrupts: The interrupt signal from the function block.
> -- clocks: device clocks
> -  See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
> -- clock-names: must contain "pixel", "engine", and "pll"
> -- port: Output port node with endpoint definitions as described in
> -  Documentation/devicetree/bindings/graph.txt. This port should be connected
> -  to the input port of an attached HDMI or LVDS encoder chip.
> -
> -Optional properties:
> -- pinctrl-names: Contain "default" and "sleep".
> -  pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
> -- pclk-sample: refer Documentation/devicetree/bindings/media/video-interfaces.txt.
> -
> -Example:
> -
> -dpi0: dpi@1401d000 {
> -	compatible = "mediatek,mt8173-dpi";
> -	reg = <0 0x1401d000 0 0x1000>;
> -	interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
> -	clocks = <&mmsys CLK_MM_DPI_PIXEL>,
> -		 <&mmsys CLK_MM_DPI_ENGINE>,
> -		 <&apmixedsys CLK_APMIXED_TVDPLL>;
> -	clock-names = "pixel", "engine", "pll";
> -	pinctrl-names = "default", "sleep";
> -	pinctrl-0 = <&dpi_pin_func>;
> -	pinctrl-1 = <&dpi_pin_idle>;
> -
> -	port {
> -		dpi0_out: endpoint {
> -			pclk-sample = <0>;
> -			remote-endpoint = <&hdmi0_in>;
> -		};
> -	};
> -};
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
> new file mode 100644
> index 000000000000..d65543e3bf8c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
> @@ -0,0 +1,103 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/mediatek/mediatek,dpi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: mediatek DPI Controller Device Tree Bindings
> +
> +maintainers:
> +  - CK Hu <ck.hu@mediatek.com>
> +  - Jitao shi <jitao.shi@mediatek.com>
> +
> +description: |
> +  The Mediatek DPI function block is a sink of the display subsystem and
> +  provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
> +  output bus.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - mediatek,mt2701-dpi
> +      - mediatek,mt8173-dpi
> +      - mediatek,mt8183-dpi
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    items:
> +      - description: Pixel Clock
> +      - description: Engine Clock
> +      - description: DPI PLL
> +
> +  clock-names:
> +    items:
> +      - const: pixel
> +      - const: engine
> +      - const: pll
> +
> +  pinctrl-0: true
> +  pinctrl-1: true
> +
> +  pinctrl-names:
> +    items:
> +      - const: default
> +      - const: sleep
> +
> +  port@0:
> +    type: object
> +    description:
> +      Output port node with endpoint definitions as described in
> +      Documentation/devicetree/bindings/graph.txt. This port should be connected
> +      to the input port of an attached HDMI or LVDS encoder chip.
> +
> +    properties:
> +      endpoint:
> +        type: object
> +
> +        properties:
> +          pclk-sample:
> +            items:
> +            - description: refer Documentation/devicetree/bindings/media/video-interfaces.txt.

This is not an array.

Just 'pclk-sample: true' if both values are allowed or 'const: 0|1' if 
only one value is allowed.

> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks
> +  - clock-names
> +  - port@0
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/clock/mt8173-clk.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    dpi0: dpi@1401d000 {
> +        compatible = "mediatek,mt8173-dpi";
> +        reg = <0 0x1401d000 0 0x1000>;
> +        interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
> +        clocks = <&mmsys CLK_MM_DPI_PIXEL>,
> +             <&mmsys CLK_MM_DPI_ENGINE>,
> +             <&apmixedsys CLK_APMIXED_TVDPLL>;
> +        clock-names = "pixel", "engine", "pll";
> +        pinctrl-names = "default", "sleep";
> +        pinctrl-0 = <&dpi_pin_func>;
> +        pinctrl-1 = <&dpi_pin_idle>;
> +
> +        port@0 {
> +            dpi0_out: endpoint {
> +                pclk-sample = <0>;
> +                remote-endpoint = <&hdmi0_in>;
> +            };
> +        };
> +    };
> +
> +...
> -- 
> 2.21.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v13 5/6] drm/mediatek: dpi sample mode support

[Jitao Shi]

DPI can sample on falling, rising or both edge.
When DPI sample the data both rising and falling edge.
It can reduce half data io pins.

Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c | 27 +++++++++++++++++++++++++--
 1 file changed, 25 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index 087f5ce732e1..2871e68e7767 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -75,6 +75,7 @@ struct mtk_dpi {
 	enum mtk_dpi_out_bit_num bit_num;
 	enum mtk_dpi_out_channel_swap channel_swap;
 	int refcount;
+	u32 pclk_sample;
 };
 
 static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
@@ -348,6 +349,13 @@ static void mtk_dpi_config_disable_edge(struct mtk_dpi *dpi)
 		mtk_dpi_mask(dpi, dpi->conf->reg_h_fre_con, 0, EDGE_SEL_EN);
 }
 
+static void mtk_dpi_enable_pclk_sample_dual_edge(struct mtk_dpi *dpi)
+{
+	mtk_dpi_mask(dpi, DPI_DDR_SETTING, DDR_EN | DDR_4PHASE,
+		     DDR_EN | DDR_4PHASE);
+	mtk_dpi_mask(dpi, DPI_OUTPUT_SETTING, EDGE_SEL, EDGE_SEL);
+}
+
 static void mtk_dpi_config_color_format(struct mtk_dpi *dpi,
 					enum mtk_dpi_out_color_format format)
 {
@@ -439,7 +447,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	pll_rate = clk_get_rate(dpi->tvd_clk);
 
 	vm.pixelclock = pll_rate / factor;
-	clk_set_rate(dpi->pixel_clk, vm.pixelclock);
+	clk_set_rate(dpi->pixel_clk,
+		     vm.pixelclock * (dpi->pclk_sample > 1 ? 2 : 1));
 	vm.pixelclock = clk_get_rate(dpi->pixel_clk);
 
 	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
@@ -450,7 +459,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	limit.y_bottom = 0x0010;
 	limit.y_top = 0x0FE0;
 
-	dpi_pol.ck_pol = MTK_DPI_POLARITY_FALLING;
+	dpi_pol.ck_pol = dpi->pclk_sample == 1 ?
+			 MTK_DPI_POLARITY_RISING : MTK_DPI_POLARITY_FALLING;
 	dpi_pol.de_pol = MTK_DPI_POLARITY_RISING;
 	dpi_pol.hsync_pol = vm.flags & DISPLAY_FLAGS_HSYNC_HIGH ?
 			    MTK_DPI_POLARITY_FALLING : MTK_DPI_POLARITY_RISING;
@@ -504,6 +514,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	mtk_dpi_config_color_format(dpi, dpi->color_format);
 	mtk_dpi_config_2n_h_fre(dpi);
 	mtk_dpi_config_disable_edge(dpi);
+	if (dpi->pclk_sample > 1)
+		mtk_dpi_enable_pclk_sample_dual_edge(dpi);
 	mtk_dpi_sw_reset(dpi, false);
 
 	return 0;
@@ -693,6 +705,7 @@ static const struct mtk_dpi_conf mt8183_conf = {
 static int mtk_dpi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
+	struct device_node *ep;
 	struct mtk_dpi *dpi;
 	struct resource *mem;
 	int comp_id;
@@ -705,6 +718,16 @@ static int mtk_dpi_probe(struct platform_device *pdev)
 	dpi->dev = dev;
 	dpi->conf = (struct mtk_dpi_conf *)of_device_get_match_data(dev);
 
+	ep = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0);
+	if (!ep) {
+		dev_err(dev, "Failed get the endpoint port\n");
+		return -EINVAL;
+	}
+
+	/* Get the sampling edge from the endpoint. */
+	of_property_read_u32(ep, "pclk-sample", &dpi->pclk_sample);
+	of_node_put(ep);
+
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dpi->regs = devm_ioremap_resource(dev, mem);
 	if (IS_ERR(dpi->regs)) {
-- 
2.21.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v13 5/6] drm/mediatek: dpi sample mode support

[Neil Armstrong]

On 11/03/2020 08:18, Jitao Shi wrote:
> DPI can sample on falling, rising or both edge.
> When DPI sample the data both rising and falling edge.
> It can reduce half data io pins.
> 
> Reviewed-by: CK Hu <ck.hu@mediatek.com>
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c | 27 +++++++++++++++++++++++++--
>  1 file changed, 25 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index 087f5ce732e1..2871e68e7767 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -75,6 +75,7 @@ struct mtk_dpi {
>  	enum mtk_dpi_out_bit_num bit_num;
>  	enum mtk_dpi_out_channel_swap channel_swap;
>  	int refcount;
> +	u32 pclk_sample;
>  };
>  
>  static inline struct mtk_dpi *mtk_dpi_from_encoder(struct drm_encoder *e)
> @@ -348,6 +349,13 @@ static void mtk_dpi_config_disable_edge(struct mtk_dpi *dpi)
>  		mtk_dpi_mask(dpi, dpi->conf->reg_h_fre_con, 0, EDGE_SEL_EN);
>  }
>  
> +static void mtk_dpi_enable_pclk_sample_dual_edge(struct mtk_dpi *dpi)
> +{
> +	mtk_dpi_mask(dpi, DPI_DDR_SETTING, DDR_EN | DDR_4PHASE,
> +		     DDR_EN | DDR_4PHASE);
> +	mtk_dpi_mask(dpi, DPI_OUTPUT_SETTING, EDGE_SEL, EDGE_SEL);
> +}
> +
>  static void mtk_dpi_config_color_format(struct mtk_dpi *dpi,
>  					enum mtk_dpi_out_color_format format)
>  {
> @@ -439,7 +447,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
>  	pll_rate = clk_get_rate(dpi->tvd_clk);
>  
>  	vm.pixelclock = pll_rate / factor;
> -	clk_set_rate(dpi->pixel_clk, vm.pixelclock);
> +	clk_set_rate(dpi->pixel_clk,
> +		     vm.pixelclock * (dpi->pclk_sample > 1 ? 2 : 1));
>  	vm.pixelclock = clk_get_rate(dpi->pixel_clk);
>  
>  	dev_dbg(dpi->dev, "Got  PLL %lu Hz, pixel clock %lu Hz\n",
> @@ -450,7 +459,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
>  	limit.y_bottom = 0x0010;
>  	limit.y_top = 0x0FE0;
>  
> -	dpi_pol.ck_pol = MTK_DPI_POLARITY_FALLING;
> +	dpi_pol.ck_pol = dpi->pclk_sample == 1 ?
> +			 MTK_DPI_POLARITY_RISING : MTK_DPI_POLARITY_FALLING;
>  	dpi_pol.de_pol = MTK_DPI_POLARITY_RISING;
>  	dpi_pol.hsync_pol = vm.flags & DISPLAY_FLAGS_HSYNC_HIGH ?
>  			    MTK_DPI_POLARITY_FALLING : MTK_DPI_POLARITY_RISING;
> @@ -504,6 +514,8 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
>  	mtk_dpi_config_color_format(dpi, dpi->color_format);
>  	mtk_dpi_config_2n_h_fre(dpi);
>  	mtk_dpi_config_disable_edge(dpi);
> +	if (dpi->pclk_sample > 1)
> +		mtk_dpi_enable_pclk_sample_dual_edge(dpi);
>  	mtk_dpi_sw_reset(dpi, false);
>  
>  	return 0;
> @@ -693,6 +705,7 @@ static const struct mtk_dpi_conf mt8183_conf = {
>  static int mtk_dpi_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
> +	struct device_node *ep;
>  	struct mtk_dpi *dpi;
>  	struct resource *mem;
>  	int comp_id;
> @@ -705,6 +718,16 @@ static int mtk_dpi_probe(struct platform_device *pdev)
>  	dpi->dev = dev;
>  	dpi->conf = (struct mtk_dpi_conf *)of_device_get_match_data(dev);
>  
> +	ep = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0);
> +	if (!ep) {
> +		dev_err(dev, "Failed get the endpoint port\n");
> +		return -EINVAL;
> +	}
> +
> +	/* Get the sampling edge from the endpoint. */
> +	of_property_read_u32(ep, "pclk-sample", &dpi->pclk_sample);
> +	of_node_put(ep);

Instead of having hard-coded value in DT, you should switch to bridge bus
format negotiation instead.

Boris pushed support a few weeks ago and the dw-hdmi bridge has been updated
to work with it and negotiate the format between the encoder and the bridge.

Phong is pushing the it66121 bridge driver which is used on a MT8183 board, and
should make use of that to handle the dual edge support between the 8183 dpi and
the it66121 bridge.

Neil

> +
>  	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>  	dpi->regs = devm_ioremap_resource(dev, mem);
>  	if (IS_ERR(dpi->regs)) {
> 

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v13 6/6] drm/mediatek: set dpi pin mode to gpio low to avoid leakage current

[Jitao Shi]

Config dpi pins mode to output and pull low when dpi is disabled.
Aovid leakage current from some dpi pins (Hsync Vsync DE ... ).

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c | 31 ++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index 2871e68e7767..b6359e979588 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -10,7 +10,9 @@
 #include <linux/kernel.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_gpio.h>
 #include <linux/of_graph.h>
+#include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/types.h>
 
@@ -74,6 +76,9 @@ struct mtk_dpi {
 	enum mtk_dpi_out_yc_map yc_map;
 	enum mtk_dpi_out_bit_num bit_num;
 	enum mtk_dpi_out_channel_swap channel_swap;
+	struct pinctrl *pinctrl;
+	struct pinctrl_state *pins_gpio;
+	struct pinctrl_state *pins_dpi;
 	int refcount;
 	u32 pclk_sample;
 };
@@ -387,6 +392,9 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi)
 	if (--dpi->refcount != 0)
 		return;
 
+	if (dpi->pinctrl && dpi->pins_gpio)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
+
 	mtk_dpi_disable(dpi);
 	clk_disable_unprepare(dpi->pixel_clk);
 	clk_disable_unprepare(dpi->engine_clk);
@@ -411,6 +419,9 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi)
 		goto err_pixel;
 	}
 
+	if (dpi->pinctrl && dpi->pins_dpi)
+		pinctrl_select_state(dpi->pinctrl, dpi->pins_dpi);
+
 	mtk_dpi_enable(dpi);
 	return 0;
 
@@ -728,6 +739,26 @@ static int mtk_dpi_probe(struct platform_device *pdev)
 	of_property_read_u32(ep, "pclk-sample", &dpi->pclk_sample);
 	of_node_put(ep);
 
+	dpi->pinctrl = devm_pinctrl_get(&pdev->dev);
+	if (IS_ERR(dpi->pinctrl)) {
+		dpi->pinctrl = NULL;
+		dev_dbg(&pdev->dev, "Cannot find pinctrl!\n");
+	}
+	if (dpi->pinctrl) {
+		dpi->pins_gpio = pinctrl_lookup_state(dpi->pinctrl, "sleep");
+		if (IS_ERR(dpi->pins_gpio)) {
+			dpi->pins_gpio = NULL;
+			dev_dbg(&pdev->dev, "Cannot find pinctrl idle!\n");
+		}
+		if (dpi->pins_gpio)
+			pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
+
+		dpi->pins_dpi = pinctrl_lookup_state(dpi->pinctrl, "default");
+		if (IS_ERR(dpi->pins_dpi)) {
+			dpi->pins_dpi = NULL;
+			dev_dbg(&pdev->dev, "Cannot find pinctrl active!\n");
+		}
+	}
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dpi->regs = devm_ioremap_resource(dev, mem);
 	if (IS_ERR(dpi->regs)) {
-- 
2.21.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v13 6/6] drm/mediatek: set dpi pin mode to gpio low to avoid leakage current

[Chun-Kuang Hu]

[-- Attachment #1.1: Type: text/plain, Size: 3509 bytes --]

Jitao Shi <jitao.shi@mediatek.com> 於 2020年3月11日 週三 下午3:19寫道：

> Config dpi pins mode to output and pull low when dpi is disabled.
> Aovid leakage current from some dpi pins (Hsync Vsync DE ... ).
>
>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>


> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c | 31 ++++++++++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
>
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c
> b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index 2871e68e7767..b6359e979588 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -10,7 +10,9 @@
>  #include <linux/kernel.h>
>  #include <linux/of.h>
>  #include <linux/of_device.h>
> +#include <linux/of_gpio.h>
>  #include <linux/of_graph.h>
> +#include <linux/pinctrl/consumer.h>
>  #include <linux/platform_device.h>
>  #include <linux/types.h>
>
> @@ -74,6 +76,9 @@ struct mtk_dpi {
>         enum mtk_dpi_out_yc_map yc_map;
>         enum mtk_dpi_out_bit_num bit_num;
>         enum mtk_dpi_out_channel_swap channel_swap;
> +       struct pinctrl *pinctrl;
> +       struct pinctrl_state *pins_gpio;
> +       struct pinctrl_state *pins_dpi;
>         int refcount;
>         u32 pclk_sample;
>  };
> @@ -387,6 +392,9 @@ static void mtk_dpi_power_off(struct mtk_dpi *dpi)
>         if (--dpi->refcount != 0)
>                 return;
>
> +       if (dpi->pinctrl && dpi->pins_gpio)
> +               pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
> +
>         mtk_dpi_disable(dpi);
>         clk_disable_unprepare(dpi->pixel_clk);
>         clk_disable_unprepare(dpi->engine_clk);
> @@ -411,6 +419,9 @@ static int mtk_dpi_power_on(struct mtk_dpi *dpi)
>                 goto err_pixel;
>         }
>
> +       if (dpi->pinctrl && dpi->pins_dpi)
> +               pinctrl_select_state(dpi->pinctrl, dpi->pins_dpi);
> +
>         mtk_dpi_enable(dpi);
>         return 0;
>
> @@ -728,6 +739,26 @@ static int mtk_dpi_probe(struct platform_device *pdev)
>         of_property_read_u32(ep, "pclk-sample", &dpi->pclk_sample);
>         of_node_put(ep);
>
> +       dpi->pinctrl = devm_pinctrl_get(&pdev->dev);
> +       if (IS_ERR(dpi->pinctrl)) {
> +               dpi->pinctrl = NULL;
> +               dev_dbg(&pdev->dev, "Cannot find pinctrl!\n");
> +       }
> +       if (dpi->pinctrl) {
> +               dpi->pins_gpio = pinctrl_lookup_state(dpi->pinctrl,
> "sleep");
> +               if (IS_ERR(dpi->pins_gpio)) {
> +                       dpi->pins_gpio = NULL;
> +                       dev_dbg(&pdev->dev, "Cannot find pinctrl idle!\n");
> +               }
> +               if (dpi->pins_gpio)
> +                       pinctrl_select_state(dpi->pinctrl, dpi->pins_gpio);
> +
> +               dpi->pins_dpi = pinctrl_lookup_state(dpi->pinctrl,
> "default");
> +               if (IS_ERR(dpi->pins_dpi)) {
> +                       dpi->pins_dpi = NULL;
> +                       dev_dbg(&pdev->dev, "Cannot find pinctrl
> active!\n");
> +               }
> +       }
>         mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>         dpi->regs = devm_ioremap_resource(dev, mem);
>         if (IS_ERR(dpi->regs)) {
> --
> 2.21.0
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
>

[-- Attachment #1.2: Type: text/html, Size: 6104 bytes --]

[-- Attachment #2: Type: text/plain, Size: 160 bytes --]

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel