From: Matt Roper <matthew.d.roper@intel.com>
To: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Subject: Re: [Intel-gfx] [PATCH v5 07/22] drm/i915/dg1: Add and setup DPLLs for DG1
Date: Tue, 28 Jul 2020 15:14:46 -0700 [thread overview]
Message-ID: <20200728221446.GG35208@mdroper-desk1.amr.corp.intel.com> (raw)
In-Reply-To: <20200724213918.27424-8-lucas.demarchi@intel.com>
On Fri, Jul 24, 2020 at 02:39:03PM -0700, Lucas De Marchi wrote:
> From: Aditya Swarup <aditya.swarup@intel.com>
>
> Add entries for dg1 plls and setup dg1_pll_mgr to reuse icl callbacks.
> Initial setup for shared dplls DPLL0/1 for DDIA/B and DPLL2/3 for
> DDIC/D. Configure dpll cfgcrx registers to drive the plls on DG1.
As on the previous patch, let's use the DG1 "DDI-TC1" and "DDI-TC2"
terminology to avoid confusion (especially since the C/D here aren't
even the same as the PORT_D/PORT_E that they index as in the driver).
>
> Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
> ---
> drivers/gpu/drm/i915/display/intel_dpll_mgr.c | 41 +++++++++++++++++--
> 1 file changed, 37 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_dpll_mgr.c b/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
> index 81ab975fe4f0..39a53aa0b233 100644
> --- a/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
> +++ b/drivers/gpu/drm/i915/display/intel_dpll_mgr.c
> @@ -3512,7 +3512,17 @@ static bool icl_get_combo_phy_dpll(struct intel_atomic_state *state,
>
> icl_calc_dpll_state(dev_priv, &pll_params, &port_dpll->hw_state);
>
> - if (IS_ROCKETLAKE(dev_priv)) {
> + if (IS_DG1(dev_priv)) {
> + if (port == PORT_D || port == PORT_E) {
> + dpll_mask =
> + BIT(DPLL_ID_DG1_DPLL2) |
> + BIT(DPLL_ID_DG1_DPLL3);
> + } else {
> + dpll_mask =
> + BIT(DPLL_ID_DG1_DPLL0) |
> + BIT(DPLL_ID_DG1_DPLL1);
> + }
> + } else if (IS_ROCKETLAKE(dev_priv)) {
> dpll_mask =
> BIT(DPLL_ID_EHL_DPLL4) |
> BIT(DPLL_ID_ICL_DPLL1) |
> @@ -3808,7 +3818,10 @@ static bool icl_pll_get_hw_state(struct drm_i915_private *dev_priv,
> if (!(val & PLL_ENABLE))
> goto out;
>
> - if (IS_ROCKETLAKE(dev_priv)) {
> + if (IS_DG1(dev_priv)) {
> + hw_state->cfgcr0 = intel_de_read(dev_priv, DG1_DPLL_CFGCR0(id));
> + hw_state->cfgcr1 = intel_de_read(dev_priv, DG1_DPLL_CFGCR1(id));
> + } else if (IS_ROCKETLAKE(dev_priv)) {
> hw_state->cfgcr0 = intel_de_read(dev_priv,
> RKL_DPLL_CFGCR0(id));
> hw_state->cfgcr1 = intel_de_read(dev_priv,
> @@ -3866,7 +3879,10 @@ static void icl_dpll_write(struct drm_i915_private *dev_priv,
> const enum intel_dpll_id id = pll->info->id;
> i915_reg_t cfgcr0_reg, cfgcr1_reg;
>
> - if (IS_ROCKETLAKE(dev_priv)) {
> + if (IS_DG1(dev_priv)) {
> + cfgcr0_reg = DG1_DPLL_CFGCR0(id);
> + cfgcr1_reg = DG1_DPLL_CFGCR1(id);
> + } else if (IS_ROCKETLAKE(dev_priv)) {
> cfgcr0_reg = RKL_DPLL_CFGCR0(id);
> cfgcr1_reg = RKL_DPLL_CFGCR1(id);
> } else if (INTEL_GEN(dev_priv) >= 12) {
> @@ -4316,6 +4332,21 @@ static const struct intel_dpll_mgr rkl_pll_mgr = {
> .dump_hw_state = icl_dump_hw_state,
> };
>
> +static const struct dpll_info dg1_plls[] = {
> + { "DPLL 0", &combo_pll_funcs, DPLL_ID_DG1_DPLL0, 0 },
> + { "DPLL 1", &combo_pll_funcs, DPLL_ID_DG1_DPLL1, 0 },
> + { "DPLL 2", &combo_pll_funcs, DPLL_ID_DG1_DPLL2, 0 },
> + { "DPLL 3", &combo_pll_funcs, DPLL_ID_DG1_DPLL3, 0 },
> + { },
> +};
> +
> +static const struct intel_dpll_mgr dg1_pll_mgr = {
> + .dpll_info = dg1_plls,
> + .get_dplls = icl_get_dplls,
> + .put_dplls = icl_put_dplls,
> + .dump_hw_state = icl_dump_hw_state,
Do we also need a
.update_ref_clks = icl_update_dpll_ref_clks,
here? That's a new hook as of ccc495fd7ac3 ("drm/i915: Unify the DPLL
ref clock frequency tracking").
Matt
> +};
> +
> /**
> * intel_shared_dpll_init - Initialize shared DPLLs
> * @dev: drm device
> @@ -4329,7 +4360,9 @@ void intel_shared_dpll_init(struct drm_device *dev)
> const struct dpll_info *dpll_info;
> int i;
>
> - if (IS_ROCKETLAKE(dev_priv))
> + if (IS_DG1(dev_priv))
> + dpll_mgr = &dg1_pll_mgr;
> + else if (IS_ROCKETLAKE(dev_priv))
> dpll_mgr = &rkl_pll_mgr;
> else if (INTEL_GEN(dev_priv) >= 12)
> dpll_mgr = &tgl_pll_mgr;
> --
> 2.26.2
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Matt Roper
Graphics Software Engineer
VTT-OSGC Platform Enablement
Intel Corporation
(916) 356-2795
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2020-07-28 22:14 UTC|newest]
Thread overview: 46+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-24 21:38 [Intel-gfx] [PATCH v5 00/22] Introduce DG1 Lucas De Marchi
2020-07-24 21:38 ` [Intel-gfx] [PATCH v5 01/22] drm/i915/dg1: Initialize RAWCLK properly Lucas De Marchi
2020-07-28 16:35 ` Souza, Jose
2020-07-24 21:38 ` [Intel-gfx] [PATCH v5 02/22] drm/i915/dg1: Define MOCS table for DG1 Lucas De Marchi
2020-07-28 19:38 ` Matt Roper
2020-07-24 21:38 ` [Intel-gfx] [PATCH v5 03/22] drm/i915/dg1: Add DG1 power wells Lucas De Marchi
2020-07-28 20:51 ` Matt Roper
2020-08-13 7:59 ` Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 04/22] drm/i915/dg1: Increase mmio size to 4MB Lucas De Marchi
2020-07-28 21:48 ` Matt Roper
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 05/22] drm/i915/dg1: Wait for pcode/uncore handshake at startup Lucas De Marchi
2020-08-03 23:24 ` Souza, Jose
2020-08-24 19:24 ` Lucas De Marchi
2020-08-24 19:29 ` Souza, Jose
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 06/22] drm/i915/dg1: Add DPLL macros for DG1 Lucas De Marchi
2020-07-28 21:54 ` Matt Roper
2020-08-13 8:07 ` Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 07/22] drm/i915/dg1: Add and setup DPLLs " Lucas De Marchi
2020-07-28 22:14 ` Matt Roper [this message]
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 08/22] drm/i915/dg1: Enable DPLL " Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 09/22] drm/i915/dg1: add hpd interrupt handling Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 10/22] drm/i915/dg1: invert HPD pins Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 11/22] drm/i915/dg1: gmbus pin mapping Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 12/22] drm/i915/dg1: Enable first 2 ports for DG1 Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 13/22] drm/i915/dg1: Don't program PHY_MISC for PHY-C and PHY-D Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 14/22] drm/i915/dg1: Update comp master/slave relationships for PHYs Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 15/22] drm/i915/dg1: Update voltage swing tables for DP Lucas De Marchi
2020-08-03 23:48 ` Souza, Jose
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 16/22] drm/i915/dg1: provide port/phy mapping for vbt Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 17/22] drm/i915/dg1: map/unmap pll clocks Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 18/22] drm/i915/dg1: enable PORT C/D aka D/E Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 19/22] drm/i915/dg1: Load DMC Lucas De Marchi
2020-08-03 23:27 ` Souza, Jose
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 20/22] drm/i915/dg1: Add initial DG1 workarounds Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 21/22] drm/i915/dg1: DG1 does not support DC6 Lucas De Marchi
2020-08-03 23:33 ` Souza, Jose
2020-08-24 21:26 ` Lucas De Marchi
2020-07-24 21:39 ` [Intel-gfx] [PATCH v5 22/22] drm/i915/dg1: Change DMC_DEBUG{1, 2} registers Lucas De Marchi
2020-08-03 23:31 ` Souza, Jose
2020-08-07 13:14 ` Anshuman Gupta
2020-08-07 17:26 ` Souza, Jose
2020-08-10 5:48 ` Anshuman Gupta
2020-08-13 7:56 ` Lucas De Marchi
2020-07-24 21:45 ` [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Introduce DG1 Patchwork
2020-07-24 21:46 ` [Intel-gfx] ✗ Fi.CI.SPARSE: " Patchwork
2020-07-24 22:08 ` [Intel-gfx] ✗ Fi.CI.BAT: failure " Patchwork
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200728221446.GG35208@mdroper-desk1.amr.corp.intel.com \
--to=matthew.d.roper@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=lucas.demarchi@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).