linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v2 0/2] am335x: set pinmux registers from pins debug file
@ 2021-05-17 20:00 Dario Binacchi
  2021-05-17 20:00 ` [PATCH v2 2/2] pinctrl: single: set pinmux " Dario Binacchi
  2021-05-19 11:31 ` [PATCH v2 0/2] am335x: set pinmux registers " Andy Shevchenko
  0 siblings, 2 replies; 6+ messages in thread
From: Dario Binacchi @ 2021-05-17 20:00 UTC (permalink / raw)
  To: linux-kernel
  Cc: Dario Binacchi, Haojian Zhuang, Linus Walleij, Tony Lindgren,
	linux-arm-kernel, linux-gpio, linux-omap


The patch was born from the need to change the slew rate of the LCD pins
of a custom AM335x board during EMC tests. The AM335x, as described in a
note in section 9.1 of its reference manual [1], is unable to write
pinmux registers from user space. The series now makes it possible to
write these registers from the pins debug file.

[1] https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf


Changes in v2:
- Remove CONFIG_SOC_AM33XX dependency.

Dario Binacchi (2):
  pinctrl: core: configure pinmux from pins debug file
  pinctrl: single: set pinmux from pins debug file

 drivers/pinctrl/core.c           | 56 ++++++++++++++++++++++++++++++--
 drivers/pinctrl/pinctrl-single.c | 20 ++++++++++++
 include/linux/pinctrl/pinctrl.h  |  2 ++
 3 files changed, 76 insertions(+), 2 deletions(-)

-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH v2 2/2] pinctrl: single: set pinmux from pins debug file
  2021-05-17 20:00 [PATCH v2 0/2] am335x: set pinmux registers from pins debug file Dario Binacchi
@ 2021-05-17 20:00 ` Dario Binacchi
  2021-05-18  6:05   ` Tony Lindgren
  2021-05-19 11:31 ` [PATCH v2 0/2] am335x: set pinmux registers " Andy Shevchenko
  1 sibling, 1 reply; 6+ messages in thread
From: Dario Binacchi @ 2021-05-17 20:00 UTC (permalink / raw)
  To: linux-kernel
  Cc: Dario Binacchi, Haojian Zhuang, Linus Walleij, Tony Lindgren,
	linux-arm-kernel, linux-gpio, linux-omap

As described in section 9.1 of the TI reference manual for AM335x [1],
"For writing to the control module registers, the MPU will need to be in
privileged mode of operation and writes will not work from user mode".
By adding the pin_dbg_set helper to pcs_pinctrl_ops it will be possible
to write these registers from the pins debug:

cd /sys/kernel/debug/pinctrl/44e10800.pinmux-pinctrl-single/
echo <pin-number> <reg-value> >pins

[1] https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf

Signed-off-by: Dario Binacchi <dariobin@libero.it>

---

Changes in v2:
- Remove CONFIG_SOC_AM33XX dependency.

 drivers/pinctrl/pinctrl-single.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/drivers/pinctrl/pinctrl-single.c b/drivers/pinctrl/pinctrl-single.c
index 2c9c9835f375..8497414e3384 100644
--- a/drivers/pinctrl/pinctrl-single.c
+++ b/drivers/pinctrl/pinctrl-single.c
@@ -313,6 +313,23 @@ static void pcs_pin_dbg_show(struct pinctrl_dev *pctldev,
 	seq_printf(s, "%zx %08x %s ", pa, val, DRIVER_NAME);
 }
 
+static int pcs_pin_dbg_set(struct pinctrl_dev *pctldev, unsigned int pin,
+			   char *buf)
+{
+	struct pcs_device *pcs;
+	unsigned int val, mux_bytes;
+
+	buf = skip_spaces(buf);
+	if (kstrtouint(buf, 0, &val))
+		return -EINVAL;
+
+	pcs = pinctrl_dev_get_drvdata(pctldev);
+
+	mux_bytes = pcs->width / BITS_PER_BYTE;
+	pcs->write(val, pcs->base + pin * mux_bytes);
+	return 0;
+}
+
 static void pcs_dt_free_map(struct pinctrl_dev *pctldev,
 				struct pinctrl_map *map, unsigned num_maps)
 {
@@ -331,6 +348,9 @@ static const struct pinctrl_ops pcs_pinctrl_ops = {
 	.get_group_name = pinctrl_generic_get_group_name,
 	.get_group_pins = pinctrl_generic_get_group_pins,
 	.pin_dbg_show = pcs_pin_dbg_show,
+#if IS_ENABLED(CONFIG_DEVMEM)
+	.pin_dbg_set = pcs_pin_dbg_set,
+#endif
 	.dt_node_to_map = pcs_dt_node_to_map,
 	.dt_free_map = pcs_dt_free_map,
 };
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v2 2/2] pinctrl: single: set pinmux from pins debug file
  2021-05-17 20:00 ` [PATCH v2 2/2] pinctrl: single: set pinmux " Dario Binacchi
@ 2021-05-18  6:05   ` Tony Lindgren
  2021-05-18  8:57     ` Dario Binacchi
  0 siblings, 1 reply; 6+ messages in thread
From: Tony Lindgren @ 2021-05-18  6:05 UTC (permalink / raw)
  To: Dario Binacchi
  Cc: linux-kernel, Haojian Zhuang, Linus Walleij, linux-arm-kernel,
	linux-gpio, linux-omap

Hi,

I noticed few more things I started to wonder about after
looking at this again.

* Dario Binacchi <dariobin@libero.it> [210517 20:00]:
> +static int pcs_pin_dbg_set(struct pinctrl_dev *pctldev, unsigned int pin,
> +			   char *buf)
> +{
> +	struct pcs_device *pcs;
> +	unsigned int val, mux_bytes;
> +
> +	buf = skip_spaces(buf);
> +	if (kstrtouint(buf, 0, &val))
> +		return -EINVAL;
> +
> +	pcs = pinctrl_dev_get_drvdata(pctldev);
> +
> +	mux_bytes = pcs->width / BITS_PER_BYTE;
> +	pcs->write(val, pcs->base + pin * mux_bytes);
> +	return 0;
> +}

Since you're adding a new interface, how about pass unsigned
int val instead of char *buf?

>  static void pcs_dt_free_map(struct pinctrl_dev *pctldev,
>  				struct pinctrl_map *map, unsigned num_maps)
>  {
> @@ -331,6 +348,9 @@ static const struct pinctrl_ops pcs_pinctrl_ops = {
>  	.get_group_name = pinctrl_generic_get_group_name,
>  	.get_group_pins = pinctrl_generic_get_group_pins,
>  	.pin_dbg_show = pcs_pin_dbg_show,
> +#if IS_ENABLED(CONFIG_DEVMEM)
> +	.pin_dbg_set = pcs_pin_dbg_set,
> +#endif
>  	.dt_node_to_map = pcs_dt_node_to_map,
>  	.dt_free_map = pcs_dt_free_map,
>  };

It might be better to always have the .pin_dbg_set around to
avoid the IS_ENABLED(CONFIG_DEVMEM).

Does the new interface need something under Documentation too?

Regards,

Tony

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v2 2/2] pinctrl: single: set pinmux from pins debug file
  2021-05-18  6:05   ` Tony Lindgren
@ 2021-05-18  8:57     ` Dario Binacchi
  2021-05-21  9:25       ` Tony Lindgren
  0 siblings, 1 reply; 6+ messages in thread
From: Dario Binacchi @ 2021-05-18  8:57 UTC (permalink / raw)
  To: Tony Lindgren
  Cc: linux-kernel, Haojian Zhuang, Linus Walleij, linux-arm-kernel,
	linux-gpio, linux-omap

Hi Tony,

> Il 18/05/2021 08:05 Tony Lindgren <tony@atomide.com> ha scritto:
> 
>  
> Hi,
> 
> I noticed few more things I started to wonder about after
> looking at this again.
> 
> * Dario Binacchi <dariobin@libero.it> [210517 20:00]:
> > +static int pcs_pin_dbg_set(struct pinctrl_dev *pctldev, unsigned int pin,
> > +			   char *buf)
> > +{
> > +	struct pcs_device *pcs;
> > +	unsigned int val, mux_bytes;
> > +
> > +	buf = skip_spaces(buf);
> > +	if (kstrtouint(buf, 0, &val))
> > +		return -EINVAL;
> > +
> > +	pcs = pinctrl_dev_get_drvdata(pctldev);
> > +
> > +	mux_bytes = pcs->width / BITS_PER_BYTE;
> > +	pcs->write(val, pcs->base + pin * mux_bytes);
> > +	return 0;
> > +}
> 
> Since you're adding a new interface, how about pass unsigned
> int val instead of char *buf?

I thought about passing char *buf because it seemed more generic 
to me. As the output of pin_dbg_show() depends on the platform 
driver, perhaps pin_dbg_set() may need driver-dependent data.
Is it possible that only the value to be set in the register 
(unsigned int) is required?

> 
> >  static void pcs_dt_free_map(struct pinctrl_dev *pctldev,
> >  				struct pinctrl_map *map, unsigned num_maps)
> >  {
> > @@ -331,6 +348,9 @@ static const struct pinctrl_ops pcs_pinctrl_ops = {
> >  	.get_group_name = pinctrl_generic_get_group_name,
> >  	.get_group_pins = pinctrl_generic_get_group_pins,
> >  	.pin_dbg_show = pcs_pin_dbg_show,
> > +#if IS_ENABLED(CONFIG_DEVMEM)
> > +	.pin_dbg_set = pcs_pin_dbg_set,
> > +#endif
> >  	.dt_node_to_map = pcs_dt_node_to_map,
> >  	.dt_free_map = pcs_dt_free_map,
> >  };
> 
> It might be better to always have the .pin_dbg_set around to
> avoid the IS_ENABLED(CONFIG_DEVMEM).

Ok, I'll remove the CONFIG_DEVMEM dependency

> 
> Does the new interface need something under Documentation too?

Yes, the description of `pins` in Documentation/driver-api/pin-control.rst 
needs to be updated. I'll add another patch to the series.

Thanks and regards,
Dario

> 
> Regards,
> 
> Tony

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v2 0/2] am335x: set pinmux registers from pins debug file
  2021-05-17 20:00 [PATCH v2 0/2] am335x: set pinmux registers from pins debug file Dario Binacchi
  2021-05-17 20:00 ` [PATCH v2 2/2] pinctrl: single: set pinmux " Dario Binacchi
@ 2021-05-19 11:31 ` Andy Shevchenko
  1 sibling, 0 replies; 6+ messages in thread
From: Andy Shevchenko @ 2021-05-19 11:31 UTC (permalink / raw)
  To: Dario Binacchi
  Cc: Linux Kernel Mailing List, Haojian Zhuang, Linus Walleij,
	Tony Lindgren, linux-arm Mailing List, open list:GPIO SUBSYSTEM,
	Linux OMAP Mailing List

On Wed, May 19, 2021 at 3:58 AM Dario Binacchi <dariobin@libero.it> wrote:
>
>
> The patch was born from the need to change the slew rate of the LCD pins
> of a custom AM335x board during EMC tests. The AM335x, as described in a
> note in section 9.1 of its reference manual [1], is unable to write
> pinmux registers from user space. The series now makes it possible to
> write these registers from the pins debug file.

Even for debugfs it would be nice to have a piece of documentation.
Because pin control is a quite sensitive area and if something goes
wrong, it may damage the hardware.

> [1] https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf


-- 
With Best Regards,
Andy Shevchenko

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v2 2/2] pinctrl: single: set pinmux from pins debug file
  2021-05-18  8:57     ` Dario Binacchi
@ 2021-05-21  9:25       ` Tony Lindgren
  0 siblings, 0 replies; 6+ messages in thread
From: Tony Lindgren @ 2021-05-21  9:25 UTC (permalink / raw)
  To: Dario Binacchi
  Cc: linux-kernel, Haojian Zhuang, Linus Walleij, linux-arm-kernel,
	linux-gpio, linux-omap

* Dario Binacchi <dariobin@libero.it> [210518 08:57]:
> I thought about passing char *buf because it seemed more generic 
> to me. As the output of pin_dbg_show() depends on the platform 
> driver, perhaps pin_dbg_set() may need driver-dependent data.
> Is it possible that only the value to be set in the register 
> (unsigned int) is required?

Maybe Linus W can answer this one.

Regards,

Tony

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, other threads:[~2021-05-21  9:27 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-05-17 20:00 [PATCH v2 0/2] am335x: set pinmux registers from pins debug file Dario Binacchi
2021-05-17 20:00 ` [PATCH v2 2/2] pinctrl: single: set pinmux " Dario Binacchi
2021-05-18  6:05   ` Tony Lindgren
2021-05-18  8:57     ` Dario Binacchi
2021-05-21  9:25       ` Tony Lindgren
2021-05-19 11:31 ` [PATCH v2 0/2] am335x: set pinmux registers " Andy Shevchenko

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).