[PATCH v2 4/6] arm64: dts: ipq6018: Add pcie support

[Baruch Siach <baruch@tkos.co.il>]

From: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>

ipq6018 has 1 pcie gen3 port. This patch adds the support for the same.

The GICv2m reg property value is a guess based on similar SoCs
description in downstream Codeaurora kernel. It appears to work.

Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
[baruch: adjust #address-cells/#size-cells; drop unsupported property;
 increase parf registers size]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
---
v2: remove 'msi-parent'; doesn't really work
---
 arch/arm64/boot/dts/qcom/ipq6018.dtsi | 99 +++++++++++++++++++++++++++
 1 file changed, 99 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index 9fa5b028e4f3..a06d10f2d73a 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -384,6 +384,105 @@ intc: interrupt-controller@b000000 {
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		pcie_phy: phy@84000 {
+			compatible = "qcom,ipq6018-qmp-pcie-phy";
+			reg = <0x0 0x84000 0x0 0x1bc>; /* Serdes PLL */
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_PCIE0_AUX_CLK>,
+				<&gcc GCC_PCIE0_AHB_CLK>;
+			clock-names = "aux", "cfg_ahb";
+
+			resets = <&gcc GCC_PCIE0_PHY_BCR>,
+				<&gcc GCC_PCIE0PHY_PHY_BCR>;
+			reset-names = "phy",
+				      "common";
+
+			pcie_phy0: lane@84200 {
+				reg = <0x0 0x84200 0x0 0x16c>, /* Serdes Tx */
+				      <0x0 0x84400 0x0 0x200>, /* Serdes Rx */
+				      <0x0 0x84800 0x0 0x4f4>; /* PCS: Lane0, COM, PCIE */
+				#phy-cells = <0>;
+
+				clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "gcc_pcie0_pipe_clk_src";
+				#clock-cells = <0>;
+			};
+		};
+
+		pcie0: pci@20000000 {
+			compatible = "qcom,pcie-ipq6018";
+			reg = <0x0 0x20000000 0x0 0xf1d>,
+			      <0x0 0x20000f20 0x0 0xa8>,
+			      <0x0 0x20001000 0x0 0x1000>,
+			      <0x0 0x80000 0x0 0x4000>,
+			      <0x0 0x20100000 0x0 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			phys = <&pcie_phy0>;
+			phy-names = "pciephy";
+
+			ranges = <0x81000000 0 0x20200000 0 0x20200000
+				  0 0x10000>, /* downstream I/O */
+				 <0x82000000 0 0x20220000 0 0x20220000
+				  0 0xfde0000>; /* non-prefetchable memory */
+
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 75
+					 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 78
+					 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 79
+					 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 83
+					 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
+				 <&gcc GCC_PCIE0_AXI_M_CLK>,
+				 <&gcc GCC_PCIE0_AXI_S_CLK>,
+				 <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
+				 <&gcc PCIE0_RCHNG_CLK>;
+			clock-names = "iface",
+				      "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng";
+
+			resets = <&gcc GCC_PCIE0_PIPE_ARES>,
+				 <&gcc GCC_PCIE0_SLEEP_ARES>,
+				 <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
+				 <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
+				 <&gcc GCC_PCIE0_AHB_ARES>,
+				 <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>;
+			reset-names = "pipe",
+				      "sleep",
+				      "sticky",
+				      "axi_m",
+				      "axi_s",
+				      "ahb",
+				      "axi_m_sticky",
+				      "axi_s_sticky";
+
+			status = "disabled";
+		};
+
 		watchdog@b017000 {
 			compatible = "qcom,kpss-wdt";
 			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
-- 
2.30.2